blob: 0966e257464a26cd273fe75893eb83f99b2ca393 [file] [log] [blame]
// SPDX-License-Identifier: GPL-2.0+
/*
* board/hoperun/hihope-rzg2/hihope-rzg2.c
* This file is HiHope RZ/G2[HMN] board support.
*
* Copyright (C) 2021 Renesas Electronics Corporation
*/
#include <asm/global_data.h>
#include <asm/io.h>
#include <asm/processor.h>
#include <asm/arch/renesas.h>
#include <asm/arch/rcar-mstp.h>
#include <linux/bitops.h>
#include <linux/delay.h>
#include <linux/libfdt.h>
#define RST_BASE 0xE6160000
#define RST_CA57RESCNT (RST_BASE + 0x40)
#define RST_CA53RESCNT (RST_BASE + 0x44)
#define RST_CA57_CODE 0xA5A5000F
#define RST_CA53_CODE 0x5A5A000F
DECLARE_GLOBAL_DATA_PTR;
#define HSUSB_MSTP704 BIT(4) /* HSUSB */
/* HSUSB block registers */
#define HSUSB_REG_LPSTS 0xE6590102
#define HSUSB_REG_LPSTS_SUSPM_NORMAL BIT(14)
#define HSUSB_REG_UGCTRL2 0xE6590184
#define HSUSB_REG_UGCTRL2_USB0SEL_EHCI 0x10
#define HSUSB_REG_UGCTRL2_RESERVED_3 0x1 /* bit[3:0] should be B'0001 */
#define PRR_REGISTER (0xFFF00044)
int board_init(void)
{
u32 i;
/* address of boot parameters */
gd->bd->bi_boot_params = CONFIG_TEXT_BASE + 0x50000;
/* Configure the HSUSB block */
mstp_clrbits_le32(SMSTPCR7, SMSTPCR7, HSUSB_MSTP704);
/*
* We need to add a barrier instruction after HSUSB module stop release.
* This barrier instruction can be either reading back the same MSTP
* register or any other register in the same IP block. So like linux
* adding check for MSTPSR register, which indicates the clock has been
* started.
*/
for (i = 1000; i > 0; --i) {
if (!(readl(MSTPSR7) & HSUSB_MSTP704))
break;
cpu_relax();
}
/* Select EHCI/OHCI host module for USB2.0 ch0 */
writel(HSUSB_REG_UGCTRL2_USB0SEL_EHCI | HSUSB_REG_UGCTRL2_RESERVED_3,
HSUSB_REG_UGCTRL2);
/* low power status */
setbits_le16(HSUSB_REG_LPSTS, HSUSB_REG_LPSTS_SUSPM_NORMAL);
return 0;
}
void reset_cpu(void)
{
unsigned long midr, cputype;
asm volatile("mrs %0, midr_el1" : "=r" (midr));
cputype = (midr >> 4) & 0xfff;
if (cputype == 0xd03)
writel(RST_CA53_CODE, RST_CA53RESCNT);
else
writel(RST_CA57_CODE, RST_CA57RESCNT);
}
#if defined(CONFIG_MULTI_DTB_FIT)
/* If the firmware passed a device tree, use it for board identification. */
extern u64 rcar_atf_boot_args[];
static bool is_hoperun_hihope_rzg2_board(const char *board_name)
{
void *atf_fdt_blob = (void *)(rcar_atf_boot_args[1]);
bool ret = false;
if ((fdt_magic(atf_fdt_blob) == FDT_MAGIC) &&
(fdt_node_check_compatible(atf_fdt_blob, 0, board_name) == 0))
ret = true;
return ret;
}
int board_fit_config_name_match(const char *name)
{
if (is_hoperun_hihope_rzg2_board("hoperun,hihope-rzg2m") &&
!strcmp(name, "r8a774a1-hihope-rzg2m-u-boot"))
return 0;
if (is_hoperun_hihope_rzg2_board("hoperun,hihope-rzg2n") &&
!strcmp(name, "r8a774b1-hihope-rzg2n-u-boot"))
return 0;
if (is_hoperun_hihope_rzg2_board("hoperun,hihope-rzg2h") &&
!strcmp(name, "r8a774e1-hihope-rzg2h-u-boot"))
return 0;
return -1;
}
#endif