| /* |
| * Configuration settings for the SAMA5D4EK board. |
| * |
| * Copyright (C) 2014 Atmel |
| * Bo Shen <voice.shen@atmel.com> |
| * |
| * SPDX-License-Identifier: GPL-2.0+ |
| */ |
| |
| #ifndef __CONFIG_H |
| #define __CONFIG_H |
| |
| #include <asm/hardware.h> |
| |
| #define CONFIG_SYS_TEXT_BASE 0x26f00000 |
| |
| /* ARM asynchronous clock */ |
| #define CONFIG_SYS_AT91_SLOW_CLOCK 32768 |
| #define CONFIG_SYS_AT91_MAIN_CLOCK 12000000 /* from 12 MHz crystal */ |
| |
| #define CONFIG_ARCH_CPU_INIT |
| |
| #define CONFIG_SKIP_LOWLEVEL_INIT |
| #define CONFIG_BOARD_EARLY_INIT_F |
| #define CONFIG_DISPLAY_CPUINFO |
| |
| #define CONFIG_CMD_BOOTZ |
| #define CONFIG_OF_LIBFDT /* Device Tree support */ |
| |
| #define CONFIG_SYS_GENERIC_BOARD |
| |
| /* general purpose I/O */ |
| #define CONFIG_AT91_GPIO |
| |
| /* serial console */ |
| #define CONFIG_ATMEL_USART |
| #define CONFIG_USART_BASE ATMEL_BASE_USART3 |
| #define CONFIG_USART_ID ATMEL_ID_USART3 |
| |
| #define CONFIG_BOOTDELAY 3 |
| |
| /* |
| * BOOTP options |
| */ |
| #define CONFIG_BOOTP_BOOTFILESIZE |
| #define CONFIG_BOOTP_BOOTPATH |
| #define CONFIG_BOOTP_GATEWAY |
| #define CONFIG_BOOTP_HOSTNAME |
| |
| /* No NOR flash */ |
| #define CONFIG_SYS_NO_FLASH |
| |
| /* |
| * Command line configuration. |
| */ |
| #include <config_cmd_default.h> |
| #undef CONFIG_CMD_FPGA |
| #undef CONFIG_CMD_IMI |
| #undef CONFIG_CMD_LOADS |
| #define CONFIG_CMD_PING |
| #define CONFIG_CMD_DHCP |
| #define CONFIG_CMD_SETEXPR |
| |
| /* SDRAM */ |
| #define CONFIG_NR_DRAM_BANKS 1 |
| #define CONFIG_SYS_SDRAM_BASE ATMEL_BASE_DDRCS |
| #define CONFIG_SYS_SDRAM_SIZE 0x20000000 |
| |
| #define CONFIG_SYS_INIT_SP_ADDR \ |
| (CONFIG_SYS_SDRAM_BASE + 4 * 1024 - GENERATED_GBL_DATA_SIZE) |
| |
| #define CONFIG_SYS_LOAD_ADDR 0x22000000 /* load address */ |
| |
| /* SerialFlash */ |
| #define CONFIG_CMD_SF |
| |
| #ifdef CONFIG_CMD_SF |
| #define CONFIG_ATMEL_SPI |
| #define CONFIG_ATMEL_SPI0 |
| #define CONFIG_SPI_FLASH |
| #define CONFIG_SPI_FLASH_ATMEL |
| #define CONFIG_SF_DEFAULT_BUS 0 |
| #define CONFIG_SF_DEFAULT_CS 0 |
| #define CONFIG_SF_DEFAULT_SPEED 30000000 |
| #endif |
| |
| /* NAND flash */ |
| #define CONFIG_CMD_NAND |
| |
| #ifdef CONFIG_CMD_NAND |
| #define CONFIG_NAND_ATMEL |
| #define CONFIG_SYS_MAX_NAND_DEVICE 1 |
| #define CONFIG_SYS_NAND_BASE ATMEL_BASE_CS3 |
| /* our ALE is AD21 */ |
| #define CONFIG_SYS_NAND_MASK_ALE (1 << 21) |
| /* our CLE is AD22 */ |
| #define CONFIG_SYS_NAND_MASK_CLE (1 << 22) |
| #define CONFIG_SYS_NAND_ONFI_DETECTION |
| /* PMECC & PMERRLOC */ |
| #define CONFIG_ATMEL_NAND_HWECC |
| #define CONFIG_ATMEL_NAND_HW_PMECC |
| #endif |
| |
| /* MMC */ |
| #define CONFIG_CMD_MMC |
| |
| #ifdef CONFIG_CMD_MMC |
| #define CONFIG_MMC |
| #define CONFIG_GENERIC_MMC |
| #define CONFIG_GENERIC_ATMEL_MCI |
| #define ATMEL_BASE_MMCI ATMEL_BASE_MCI1 |
| #endif |
| |
| /* USB */ |
| #define CONFIG_CMD_USB |
| |
| #ifdef CONFIG_CMD_USB |
| #define CONFIG_USB_EHCI |
| #define CONFIG_USB_EHCI_ATMEL |
| #define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3 |
| #define CONFIG_USB_STORAGE |
| #endif |
| |
| #if defined(CONFIG_CMD_USB) || defined(CONFIG_CMD_MMC) |
| #define CONFIG_CMD_FAT |
| #define CONFIG_DOS_PARTITION |
| #endif |
| |
| /* Ethernet Hardware */ |
| #define CONFIG_MACB |
| #define CONFIG_RMII |
| #define CONFIG_NET_RETRY_COUNT 20 |
| #define CONFIG_MACB_SEARCH_PHY |
| |
| /* LCD */ |
| #define CONFIG_LCD |
| #define LCD_BPP LCD_COLOR16 |
| #define LCD_OUTPUT_BPP 18 |
| #define CONFIG_LCD_LOGO |
| #define CONFIG_LCD_INFO |
| #define CONFIG_LCD_INFO_BELOW_LOGO |
| #define CONFIG_SYS_WHITE_ON_BLACK |
| #define CONFIG_ATMEL_HLCD |
| #define CONFIG_ATMEL_LCD_RGB565 |
| #define CONFIG_SYS_CONSOLE_IS_IN_ENV |
| |
| #ifdef CONFIG_SYS_USE_SERIALFLASH |
| /* bootstrap + u-boot + env + linux in serial flash */ |
| #define CONFIG_ENV_IS_IN_SPI_FLASH |
| #define CONFIG_ENV_SPI_BUS CONFIG_SF_DEFAULT_BUS |
| #define CONFIG_ENV_SPI_CS CONFIG_SF_DEFAULT_CS |
| #define CONFIG_ENV_OFFSET 0x10000 |
| #define CONFIG_ENV_SIZE 0x10000 |
| #define CONFIG_ENV_SECT_SIZE 0x1000 |
| #define CONFIG_BOOTCOMMAND "sf probe 0; " \ |
| "sf read 0x21000000 0xa0000 0x60000; " \ |
| "sf read 0x22000000 0x100000 0x300000; " \ |
| "bootz 0x22000000 - 0x21000000" |
| #elif CONFIG_SYS_USE_NANDFLASH |
| /* bootstrap + u-boot + env in nandflash */ |
| #define CONFIG_ENV_IS_IN_NAND |
| #define CONFIG_ENV_OFFSET 0xc0000 |
| #define CONFIG_ENV_OFFSET_REDUND 0x100000 |
| #define CONFIG_ENV_SIZE 0x20000 |
| #define CONFIG_BOOTCOMMAND "nand read 0x21000000 0x180000 0x80000;" \ |
| "nand read 0x22000000 0x200000 0x600000;" \ |
| "bootz 0x22000000 - 0x21000000" |
| #elif CONFIG_SYS_USE_MMC |
| /* bootstrap + u-boot + env in sd card */ |
| #define CONFIG_ENV_IS_IN_FAT |
| #define CONFIG_FAT_WRITE |
| #define FAT_ENV_INTERFACE "mmc" |
| /* |
| * We don't specify the part number, if device 0 has partition table, it means |
| * the first partition; it no partition table, then take whole device as a |
| * FAT file system. |
| */ |
| #define FAT_ENV_DEVICE_AND_PART "0" |
| #define FAT_ENV_FILE "uboot.env" |
| #define CONFIG_ENV_SIZE 0x4000 |
| #define CONFIG_BOOTCOMMAND "fatload mmc 0:1 0x21000000 sama5d4ek.dtb; " \ |
| "fatload mmc 0:1 0x22000000 zImage; " \ |
| "bootz 0x22000000 - 0x21000000" |
| #endif |
| |
| #ifdef CONFIG_SYS_USE_MMC |
| #define CONFIG_BOOTARGS \ |
| "console=ttyS0,115200 earlyprintk " \ |
| "root=/dev/mmcblk0p2 rw rootwait" |
| #else |
| #define CONFIG_BOOTARGS \ |
| "console=ttyS0,115200 earlyprintk " \ |
| "mtdparts=atmel_nand:256k(bootstrap)ro,512k(uboot)ro," \ |
| "256K(env),256k(evn_redundent),256k(spare)," \ |
| "512k(dtb),6M(kernel)ro,-(rootfs) " \ |
| "rootfstype=ubifs ubi.mtd=7 root=ubi0:rootfs" |
| #endif |
| |
| #define CONFIG_BAUDRATE 115200 |
| |
| #define CONFIG_SYS_PROMPT "U-Boot> " |
| #define CONFIG_SYS_CBSIZE 256 |
| #define CONFIG_SYS_MAXARGS 16 |
| #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ |
| sizeof(CONFIG_SYS_PROMPT) + 16) |
| #define CONFIG_SYS_LONGHELP |
| #define CONFIG_CMDLINE_EDITING |
| #define CONFIG_AUTO_COMPLETE |
| #define CONFIG_SYS_HUSH_PARSER |
| |
| /* Size of malloc() pool */ |
| #define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024) |
| |
| #endif |