blob: c104024b1007b1cc7dc307842d014ce6a4d231f1 [file] [log] [blame]
/*
* (C) Copyright 2010
* Texas Instruments Incorporated, <www.ti.com>
* Steve Sakoman <steve@sakoman.com>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <asm/arch/sys_proto.h>
#include <asm/arch/mmc_host_def.h>
#include <asm/arch/clock.h>
#include <asm/arch/gpio.h>
#include <asm/gpio.h>
#include "panda_mux_data.h"
#ifdef CONFIG_USB_EHCI
#include <usb.h>
#include <asm/arch/ehci.h>
#include <asm/ehci-omap.h>
#endif
#define PANDA_ULPI_PHY_TYPE_GPIO 182
#define PANDA_BOARD_ID_1_GPIO 101
#define PANDA_ES_BOARD_ID_1_GPIO 48
#define PANDA_BOARD_ID_2_GPIO 171
#define PANDA_ES_BOARD_ID_3_GPIO 3
#define PANDA_ES_BOARD_ID_4_GPIO 2
DECLARE_GLOBAL_DATA_PTR;
const struct omap_sysinfo sysinfo = {
"Board: OMAP4 Panda\n"
};
struct omap4_scrm_regs *const scrm = (struct omap4_scrm_regs *)0x4a30a000;
/**
* @brief board_init
*
* @return 0
*/
int board_init(void)
{
gpmc_init();
gd->bd->bi_arch_number = MACH_TYPE_OMAP4_PANDA;
gd->bd->bi_boot_params = (0x80000000 + 0x100); /* boot param addr */
return 0;
}
int board_eth_init(bd_t *bis)
{
return 0;
}
/*
* Routine: get_board_revision
* Description: Detect if we are running on a panda revision A1-A6,
* or an ES panda board. This can be done by reading
* the level of GPIOs and checking the processor revisions.
* This should result in:
* Panda 4430:
* GPIO171, GPIO101, GPIO182: 0 1 1 => A1-A5
* GPIO171, GPIO101, GPIO182: 1 0 1 => A6
* Panda ES:
* GPIO2, GPIO3, GPIO171, GPIO48, GPIO182: 0 0 0 1 1 => B1/B2
* GPIO2, GPIO3, GPIO171, GPIO48, GPIO182: 0 0 1 1 1 => B3
*/
int get_board_revision(void)
{
int board_id0, board_id1, board_id2;
int board_id3, board_id4;
int board_id;
int processor_rev = omap_revision();
/* Setup the mux for the common board ID pins (gpio 171 and 182) */
writew((IEN | M3), (*ctrl)->control_padconf_core_base + UNIPRO_TX0);
writew((IEN | M3), (*ctrl)->control_padconf_core_base + FREF_CLK2_OUT);
board_id0 = gpio_get_value(PANDA_ULPI_PHY_TYPE_GPIO);
board_id2 = gpio_get_value(PANDA_BOARD_ID_2_GPIO);
if ((processor_rev >= OMAP4460_ES1_0 &&
processor_rev <= OMAP4460_ES1_1)) {
/*
* Setup the mux for the ES specific board ID pins (gpio 101,
* 2 and 3.
*/
writew((IEN | M3), (*ctrl)->control_padconf_core_base +
GPMC_A24);
writew((IEN | M3), (*ctrl)->control_padconf_core_base +
UNIPRO_RY0);
writew((IEN | M3), (*ctrl)->control_padconf_core_base +
UNIPRO_RX1);
board_id1 = gpio_get_value(PANDA_ES_BOARD_ID_1_GPIO);
board_id3 = gpio_get_value(PANDA_ES_BOARD_ID_3_GPIO);
board_id4 = gpio_get_value(PANDA_ES_BOARD_ID_4_GPIO);
#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
setenv("board_name", strcat(CONFIG_SYS_BOARD, "-es"));
#endif
board_id = ((board_id4 << 4) | (board_id3 << 3) |
(board_id2 << 2) | (board_id1 << 1) | (board_id0));
} else {
/* Setup the mux for the Ax specific board ID pins (gpio 101) */
writew((IEN | M3), (*ctrl)->control_padconf_core_base +
FREF_CLK2_OUT);
board_id1 = gpio_get_value(PANDA_BOARD_ID_1_GPIO);
board_id = ((board_id2 << 2) | (board_id1 << 1) | (board_id0));
#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
if ((board_id >= 0x3) && (processor_rev == OMAP4430_ES2_3))
setenv("board_name", strcat(CONFIG_SYS_BOARD, "-a4"));
#endif
}
return board_id;
}
/**
* @brief misc_init_r - Configure Panda board specific configurations
* such as power configurations, ethernet initialization as phase2 of
* boot sequence
*
* @return 0
*/
int misc_init_r(void)
{
int phy_type;
u32 auxclk, altclksrc;
uint8_t device_mac[6];
/* EHCI is not supported on ES1.0 */
if (omap_revision() == OMAP4430_ES1_0)
return 0;
get_board_revision();
gpio_direction_input(PANDA_ULPI_PHY_TYPE_GPIO);
phy_type = gpio_get_value(PANDA_ULPI_PHY_TYPE_GPIO);
if (phy_type == 1) {
/* ULPI PHY supplied by auxclk3 derived from sys_clk */
debug("ULPI PHY supplied by auxclk3\n");
auxclk = readl(&scrm->auxclk3);
/* Select sys_clk */
auxclk &= ~AUXCLK_SRCSELECT_MASK;
auxclk |= AUXCLK_SRCSELECT_SYS_CLK << AUXCLK_SRCSELECT_SHIFT;
/* Set the divisor to 2 */
auxclk &= ~AUXCLK_CLKDIV_MASK;
auxclk |= AUXCLK_CLKDIV_2 << AUXCLK_CLKDIV_SHIFT;
/* Request auxilary clock #3 */
auxclk |= AUXCLK_ENABLE_MASK;
writel(auxclk, &scrm->auxclk3);
} else {
/* ULPI PHY supplied by auxclk1 derived from PER dpll */
debug("ULPI PHY supplied by auxclk1\n");
auxclk = readl(&scrm->auxclk1);
/* Select per DPLL */
auxclk &= ~AUXCLK_SRCSELECT_MASK;
auxclk |= AUXCLK_SRCSELECT_PER_DPLL << AUXCLK_SRCSELECT_SHIFT;
/* Set the divisor to 16 */
auxclk &= ~AUXCLK_CLKDIV_MASK;
auxclk |= AUXCLK_CLKDIV_16 << AUXCLK_CLKDIV_SHIFT;
/* Request auxilary clock #3 */
auxclk |= AUXCLK_ENABLE_MASK;
writel(auxclk, &scrm->auxclk1);
}
altclksrc = readl(&scrm->altclksrc);
/* Activate alternate system clock supplier */
altclksrc &= ~ALTCLKSRC_MODE_MASK;
altclksrc |= ALTCLKSRC_MODE_ACTIVE;
/* enable clocks */
altclksrc |= ALTCLKSRC_ENABLE_INT_MASK | ALTCLKSRC_ENABLE_EXT_MASK;
writel(altclksrc, &scrm->altclksrc);
if (!getenv("usbethaddr")) {
/*
* create a fake MAC address from the processor ID code.
* first byte is 0x02 to signify locally administered.
*/
device_mac[0] = 0x02;
device_mac[1] = readl(STD_FUSE_DIE_ID_3) & 0xff;
device_mac[2] = readl(STD_FUSE_DIE_ID_2) & 0xff;
device_mac[3] = readl(STD_FUSE_DIE_ID_1) & 0xff;
device_mac[4] = readl(STD_FUSE_DIE_ID_0) & 0xff;
device_mac[5] = (readl(STD_FUSE_DIE_ID_0) >> 8) & 0xff;
eth_setenv_enetaddr("usbethaddr", device_mac);
}
return 0;
}
void set_muxconf_regs_essential(void)
{
do_set_mux((*ctrl)->control_padconf_core_base,
core_padconf_array_essential,
sizeof(core_padconf_array_essential) /
sizeof(struct pad_conf_entry));
do_set_mux((*ctrl)->control_padconf_wkup_base,
wkup_padconf_array_essential,
sizeof(wkup_padconf_array_essential) /
sizeof(struct pad_conf_entry));
if (omap_revision() >= OMAP4460_ES1_0)
do_set_mux((*ctrl)->control_padconf_wkup_base,
wkup_padconf_array_essential_4460,
sizeof(wkup_padconf_array_essential_4460) /
sizeof(struct pad_conf_entry));
}
void set_muxconf_regs_non_essential(void)
{
do_set_mux((*ctrl)->control_padconf_core_base,
core_padconf_array_non_essential,
sizeof(core_padconf_array_non_essential) /
sizeof(struct pad_conf_entry));
if (omap_revision() < OMAP4460_ES1_0)
do_set_mux((*ctrl)->control_padconf_core_base,
core_padconf_array_non_essential_4430,
sizeof(core_padconf_array_non_essential_4430) /
sizeof(struct pad_conf_entry));
else
do_set_mux((*ctrl)->control_padconf_core_base,
core_padconf_array_non_essential_4460,
sizeof(core_padconf_array_non_essential_4460) /
sizeof(struct pad_conf_entry));
do_set_mux((*ctrl)->control_padconf_wkup_base,
wkup_padconf_array_non_essential,
sizeof(wkup_padconf_array_non_essential) /
sizeof(struct pad_conf_entry));
if (omap_revision() < OMAP4460_ES1_0)
do_set_mux((*ctrl)->control_padconf_wkup_base,
wkup_padconf_array_non_essential_4430,
sizeof(wkup_padconf_array_non_essential_4430) /
sizeof(struct pad_conf_entry));
}
#if !defined(CONFIG_SPL_BUILD) && defined(CONFIG_GENERIC_MMC)
int board_mmc_init(bd_t *bis)
{
return omap_mmc_init(0, 0, 0, -1, -1);
}
#endif
#ifdef CONFIG_USB_EHCI
static struct omap_usbhs_board_data usbhs_bdata = {
.port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
.port_mode[1] = OMAP_USBHS_PORT_MODE_UNUSED,
.port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
};
int ehci_hcd_init(int index, enum usb_init_type init,
struct ehci_hccr **hccr, struct ehci_hcor **hcor)
{
int ret;
unsigned int utmi_clk;
/* Now we can enable our port clocks */
utmi_clk = readl((void *)CM_L3INIT_HSUSBHOST_CLKCTRL);
utmi_clk |= HSUSBHOST_CLKCTRL_CLKSEL_UTMI_P1_MASK;
sr32((void *)CM_L3INIT_HSUSBHOST_CLKCTRL, 0, 32, utmi_clk);
ret = omap_ehci_hcd_init(index, &usbhs_bdata, hccr, hcor);
if (ret < 0)
return ret;
return 0;
}
int ehci_hcd_stop(int index)
{
return omap_ehci_hcd_stop();
}
#endif
/*
* get_board_rev() - get board revision
*/
u32 get_board_rev(void)
{
return 0x20;
}