| /* |
| * sata_dwc.c |
| * |
| * Synopsys DesignWare Cores (DWC) SATA host driver |
| * |
| * Author: Mark Miesfeld <mmiesfeld@amcc.com> |
| * |
| * Ported from 2.6.19.2 to 2.6.25/26 by Stefan Roese <sr@denx.de> |
| * Copyright 2008 DENX Software Engineering |
| * |
| * Based on versions provided by AMCC and Synopsys which are: |
| * Copyright 2006 Applied Micro Circuits Corporation |
| * COPYRIGHT (C) 2005 SYNOPSYS, INC. ALL RIGHTS RESERVED |
| * |
| * This program is free software; you can redistribute |
| * it and/or modify it under the terms of the GNU |
| * General Public License as published by the |
| * Free Software Foundation; either version 2 of the License, |
| * or (at your option) any later version. |
| * |
| */ |
| /* |
| * SATA support based on the chip canyonlands. |
| * |
| * 04-17-2009 |
| * The local version of this driver for the canyonlands board |
| * does not use interrupts but polls the chip instead. |
| */ |
| |
| #include <common.h> |
| #include <command.h> |
| #include <pci.h> |
| #include <asm/processor.h> |
| #include <asm/errno.h> |
| #include <asm/io.h> |
| #include <malloc.h> |
| #include <ata.h> |
| #include <linux/ctype.h> |
| |
| #include "sata_dwc.h" |
| |
| #define DMA_NUM_CHANS 1 |
| #define DMA_NUM_CHAN_REGS 8 |
| |
| #define AHB_DMA_BRST_DFLT 16 |
| |
| struct dmareg { |
| u32 low; |
| u32 high; |
| }; |
| |
| struct dma_chan_regs { |
| struct dmareg sar; |
| struct dmareg dar; |
| struct dmareg llp; |
| struct dmareg ctl; |
| struct dmareg sstat; |
| struct dmareg dstat; |
| struct dmareg sstatar; |
| struct dmareg dstatar; |
| struct dmareg cfg; |
| struct dmareg sgr; |
| struct dmareg dsr; |
| }; |
| |
| struct dma_interrupt_regs { |
| struct dmareg tfr; |
| struct dmareg block; |
| struct dmareg srctran; |
| struct dmareg dsttran; |
| struct dmareg error; |
| }; |
| |
| struct ahb_dma_regs { |
| struct dma_chan_regs chan_regs[DMA_NUM_CHAN_REGS]; |
| struct dma_interrupt_regs interrupt_raw; |
| struct dma_interrupt_regs interrupt_status; |
| struct dma_interrupt_regs interrupt_mask; |
| struct dma_interrupt_regs interrupt_clear; |
| struct dmareg statusInt; |
| struct dmareg rq_srcreg; |
| struct dmareg rq_dstreg; |
| struct dmareg rq_sgl_srcreg; |
| struct dmareg rq_sgl_dstreg; |
| struct dmareg rq_lst_srcreg; |
| struct dmareg rq_lst_dstreg; |
| struct dmareg dma_cfg; |
| struct dmareg dma_chan_en; |
| struct dmareg dma_id; |
| struct dmareg dma_test; |
| struct dmareg res1; |
| struct dmareg res2; |
| /* DMA Comp Params |
| * Param 6 = dma_param[0], Param 5 = dma_param[1], |
| * Param 4 = dma_param[2] ... |
| */ |
| struct dmareg dma_params[6]; |
| }; |
| |
| #define DMA_EN 0x00000001 |
| #define DMA_DI 0x00000000 |
| #define DMA_CHANNEL(ch) (0x00000001 << (ch)) |
| #define DMA_ENABLE_CHAN(ch) ((0x00000001 << (ch)) | \ |
| ((0x000000001 << (ch)) << 8)) |
| #define DMA_DISABLE_CHAN(ch) (0x00000000 | \ |
| ((0x000000001 << (ch)) << 8)) |
| |
| #define SATA_DWC_MAX_PORTS 1 |
| #define SATA_DWC_SCR_OFFSET 0x24 |
| #define SATA_DWC_REG_OFFSET 0x64 |
| |
| struct sata_dwc_regs { |
| u32 fptagr; |
| u32 fpbor; |
| u32 fptcr; |
| u32 dmacr; |
| u32 dbtsr; |
| u32 intpr; |
| u32 intmr; |
| u32 errmr; |
| u32 llcr; |
| u32 phycr; |
| u32 physr; |
| u32 rxbistpd; |
| u32 rxbistpd1; |
| u32 rxbistpd2; |
| u32 txbistpd; |
| u32 txbistpd1; |
| u32 txbistpd2; |
| u32 bistcr; |
| u32 bistfctr; |
| u32 bistsr; |
| u32 bistdecr; |
| u32 res[15]; |
| u32 testr; |
| u32 versionr; |
| u32 idr; |
| u32 unimpl[192]; |
| u32 dmadr[256]; |
| }; |
| |
| #define SATA_DWC_TXFIFO_DEPTH 0x01FF |
| #define SATA_DWC_RXFIFO_DEPTH 0x01FF |
| |
| #define SATA_DWC_DBTSR_MWR(size) ((size / 4) & SATA_DWC_TXFIFO_DEPTH) |
| #define SATA_DWC_DBTSR_MRD(size) (((size / 4) & \ |
| SATA_DWC_RXFIFO_DEPTH) << 16) |
| #define SATA_DWC_INTPR_DMAT 0x00000001 |
| #define SATA_DWC_INTPR_NEWFP 0x00000002 |
| #define SATA_DWC_INTPR_PMABRT 0x00000004 |
| #define SATA_DWC_INTPR_ERR 0x00000008 |
| #define SATA_DWC_INTPR_NEWBIST 0x00000010 |
| #define SATA_DWC_INTPR_IPF 0x10000000 |
| #define SATA_DWC_INTMR_DMATM 0x00000001 |
| #define SATA_DWC_INTMR_NEWFPM 0x00000002 |
| #define SATA_DWC_INTMR_PMABRTM 0x00000004 |
| #define SATA_DWC_INTMR_ERRM 0x00000008 |
| #define SATA_DWC_INTMR_NEWBISTM 0x00000010 |
| |
| #define SATA_DWC_DMACR_TMOD_TXCHEN 0x00000004 |
| #define SATA_DWC_DMACR_TXRXCH_CLEAR SATA_DWC_DMACR_TMOD_TXCHEN |
| |
| #define SATA_DWC_QCMD_MAX 32 |
| |
| #define SATA_DWC_SERROR_ERR_BITS 0x0FFF0F03 |
| |
| #define HSDEVP_FROM_AP(ap) (struct sata_dwc_device_port*) \ |
| (ap)->private_data |
| |
| struct sata_dwc_device { |
| struct device *dev; |
| struct ata_probe_ent *pe; |
| struct ata_host *host; |
| u8 *reg_base; |
| struct sata_dwc_regs *sata_dwc_regs; |
| int irq_dma; |
| }; |
| |
| struct sata_dwc_device_port { |
| struct sata_dwc_device *hsdev; |
| int cmd_issued[SATA_DWC_QCMD_MAX]; |
| u32 dma_chan[SATA_DWC_QCMD_MAX]; |
| int dma_pending[SATA_DWC_QCMD_MAX]; |
| }; |
| |
| enum { |
| SATA_DWC_CMD_ISSUED_NOT = 0, |
| SATA_DWC_CMD_ISSUED_PEND = 1, |
| SATA_DWC_CMD_ISSUED_EXEC = 2, |
| SATA_DWC_CMD_ISSUED_NODATA = 3, |
| |
| SATA_DWC_DMA_PENDING_NONE = 0, |
| SATA_DWC_DMA_PENDING_TX = 1, |
| SATA_DWC_DMA_PENDING_RX = 2, |
| }; |
| |
| #define msleep(a) udelay(a * 1000) |
| #define ssleep(a) msleep(a * 1000) |
| |
| static int ata_probe_timeout = (ATA_TMOUT_INTERNAL / 100); |
| |
| enum sata_dev_state { |
| SATA_INIT = 0, |
| SATA_READY = 1, |
| SATA_NODEVICE = 2, |
| SATA_ERROR = 3, |
| }; |
| enum sata_dev_state dev_state = SATA_INIT; |
| |
| static struct ahb_dma_regs *sata_dma_regs = 0; |
| static struct ata_host *phost; |
| static struct ata_port ap; |
| static struct ata_port *pap = ≈ |
| static struct ata_device ata_device; |
| static struct sata_dwc_device_port dwc_devp; |
| |
| static void *scr_addr_sstatus; |
| static u32 temp_n_block = 0; |
| |
| static unsigned ata_exec_internal(struct ata_device *dev, |
| struct ata_taskfile *tf, const u8 *cdb, |
| int dma_dir, unsigned int buflen, |
| unsigned long timeout); |
| static unsigned int ata_dev_set_feature(struct ata_device *dev, |
| u8 enable,u8 feature); |
| static unsigned int ata_dev_init_params(struct ata_device *dev, |
| u16 heads, u16 sectors); |
| static u8 ata_irq_on(struct ata_port *ap); |
| static struct ata_queued_cmd *__ata_qc_from_tag(struct ata_port *ap, |
| unsigned int tag); |
| static int ata_hsm_move(struct ata_port *ap, struct ata_queued_cmd *qc, |
| u8 status, int in_wq); |
| static void ata_tf_to_host(struct ata_port *ap, |
| const struct ata_taskfile *tf); |
| static void ata_exec_command(struct ata_port *ap, |
| const struct ata_taskfile *tf); |
| static unsigned int ata_qc_issue_prot(struct ata_queued_cmd *qc); |
| static u8 ata_check_altstatus(struct ata_port *ap); |
| static u8 ata_check_status(struct ata_port *ap); |
| static void ata_dev_select(struct ata_port *ap, unsigned int device, |
| unsigned int wait, unsigned int can_sleep); |
| static void ata_qc_issue(struct ata_queued_cmd *qc); |
| static void ata_tf_load(struct ata_port *ap, |
| const struct ata_taskfile *tf); |
| static int ata_dev_read_sectors(unsigned char* pdata, |
| unsigned long datalen, u32 block, u32 n_block); |
| static int ata_dev_write_sectors(unsigned char* pdata, |
| unsigned long datalen , u32 block, u32 n_block); |
| static void ata_std_dev_select(struct ata_port *ap, unsigned int device); |
| static void ata_qc_complete(struct ata_queued_cmd *qc); |
| static void __ata_qc_complete(struct ata_queued_cmd *qc); |
| static void fill_result_tf(struct ata_queued_cmd *qc); |
| static void ata_tf_read(struct ata_port *ap, struct ata_taskfile *tf); |
| static void ata_mmio_data_xfer(struct ata_device *dev, |
| unsigned char *buf, |
| unsigned int buflen,int do_write); |
| static void ata_pio_task(struct ata_port *arg_ap); |
| static void __ata_port_freeze(struct ata_port *ap); |
| static int ata_port_freeze(struct ata_port *ap); |
| static void ata_qc_free(struct ata_queued_cmd *qc); |
| static void ata_pio_sectors(struct ata_queued_cmd *qc); |
| static void ata_pio_sector(struct ata_queued_cmd *qc); |
| static void ata_pio_queue_task(struct ata_port *ap, |
| void *data,unsigned long delay); |
| static void ata_hsm_qc_complete(struct ata_queued_cmd *qc, int in_wq); |
| static int sata_dwc_softreset(struct ata_port *ap); |
| static int ata_dev_read_id(struct ata_device *dev, unsigned int *p_class, |
| unsigned int flags, u16 *id); |
| static int check_sata_dev_state(void); |
| |
| extern block_dev_desc_t sata_dev_desc[CONFIG_SYS_SATA_MAX_DEVICE]; |
| |
| static const struct ata_port_info sata_dwc_port_info[] = { |
| { |
| .flags = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY | |
| ATA_FLAG_MMIO | ATA_FLAG_PIO_POLLING | |
| ATA_FLAG_SRST | ATA_FLAG_NCQ, |
| .pio_mask = 0x1f, |
| .mwdma_mask = 0x07, |
| .udma_mask = 0x7f, |
| }, |
| }; |
| |
| int init_sata(int dev) |
| { |
| struct sata_dwc_device hsdev; |
| struct ata_host host; |
| struct ata_port_info pi = sata_dwc_port_info[0]; |
| struct ata_link *link; |
| struct sata_dwc_device_port hsdevp = dwc_devp; |
| u8 *base = 0; |
| u8 *sata_dma_regs_addr = 0; |
| u8 status; |
| unsigned long base_addr = 0; |
| int chan = 0; |
| int rc; |
| int i; |
| |
| phost = &host; |
| |
| base = (u8*)SATA_BASE_ADDR; |
| |
| hsdev.sata_dwc_regs = (void *__iomem)(base + SATA_DWC_REG_OFFSET); |
| |
| host.n_ports = SATA_DWC_MAX_PORTS; |
| |
| for (i = 0; i < SATA_DWC_MAX_PORTS; i++) { |
| ap.pflags |= ATA_PFLAG_INITIALIZING; |
| ap.flags = ATA_FLAG_DISABLED; |
| ap.print_id = -1; |
| ap.ctl = ATA_DEVCTL_OBS; |
| ap.host = &host; |
| ap.last_ctl = 0xFF; |
| |
| link = &ap.link; |
| link->ap = ≈ |
| link->pmp = 0; |
| link->active_tag = ATA_TAG_POISON; |
| link->hw_sata_spd_limit = 0; |
| |
| ap.port_no = i; |
| host.ports[i] = ≈ |
| } |
| |
| ap.pio_mask = pi.pio_mask; |
| ap.mwdma_mask = pi.mwdma_mask; |
| ap.udma_mask = pi.udma_mask; |
| ap.flags |= pi.flags; |
| ap.link.flags |= pi.link_flags; |
| |
| host.ports[0]->ioaddr.cmd_addr = base; |
| host.ports[0]->ioaddr.scr_addr = base + SATA_DWC_SCR_OFFSET; |
| scr_addr_sstatus = base + SATA_DWC_SCR_OFFSET; |
| |
| base_addr = (unsigned long)base; |
| |
| host.ports[0]->ioaddr.cmd_addr = (void *)base_addr + 0x00; |
| host.ports[0]->ioaddr.data_addr = (void *)base_addr + 0x00; |
| |
| host.ports[0]->ioaddr.error_addr = (void *)base_addr + 0x04; |
| host.ports[0]->ioaddr.feature_addr = (void *)base_addr + 0x04; |
| |
| host.ports[0]->ioaddr.nsect_addr = (void *)base_addr + 0x08; |
| |
| host.ports[0]->ioaddr.lbal_addr = (void *)base_addr + 0x0c; |
| host.ports[0]->ioaddr.lbam_addr = (void *)base_addr + 0x10; |
| host.ports[0]->ioaddr.lbah_addr = (void *)base_addr + 0x14; |
| |
| host.ports[0]->ioaddr.device_addr = (void *)base_addr + 0x18; |
| host.ports[0]->ioaddr.command_addr = (void *)base_addr + 0x1c; |
| host.ports[0]->ioaddr.status_addr = (void *)base_addr + 0x1c; |
| |
| host.ports[0]->ioaddr.altstatus_addr = (void *)base_addr + 0x20; |
| host.ports[0]->ioaddr.ctl_addr = (void *)base_addr + 0x20; |
| |
| sata_dma_regs_addr = (u8*)SATA_DMA_REG_ADDR; |
| sata_dma_regs = (void *__iomem)sata_dma_regs_addr; |
| |
| status = ata_check_altstatus(&ap); |
| |
| if (status == 0x7f) { |
| printf("Hard Disk not found.\n"); |
| dev_state = SATA_NODEVICE; |
| rc = FALSE; |
| return rc; |
| } |
| |
| printf("Waiting for device..."); |
| i = 0; |
| while (1) { |
| udelay(10000); |
| |
| status = ata_check_altstatus(&ap); |
| |
| if ((status & ATA_BUSY) == 0) { |
| printf("\n"); |
| break; |
| } |
| |
| i++; |
| if (i > (ATA_RESET_TIME * 100)) { |
| printf("** TimeOUT **\n"); |
| |
| dev_state = SATA_NODEVICE; |
| rc = FALSE; |
| return rc; |
| } |
| if ((i >= 100) && ((i % 100) == 0)) |
| printf("."); |
| } |
| |
| rc = sata_dwc_softreset(&ap); |
| |
| if (rc) { |
| printf("sata_dwc : error. soft reset failed\n"); |
| return rc; |
| } |
| |
| for (chan = 0; chan < DMA_NUM_CHANS; chan++) { |
| out_le32(&(sata_dma_regs->interrupt_mask.error.low), |
| DMA_DISABLE_CHAN(chan)); |
| |
| out_le32(&(sata_dma_regs->interrupt_mask.tfr.low), |
| DMA_DISABLE_CHAN(chan)); |
| } |
| |
| out_le32(&(sata_dma_regs->dma_cfg.low), DMA_DI); |
| |
| out_le32(&hsdev.sata_dwc_regs->intmr, |
| SATA_DWC_INTMR_ERRM | |
| SATA_DWC_INTMR_PMABRTM); |
| |
| /* Unmask the error bits that should trigger |
| * an error interrupt by setting the error mask register. |
| */ |
| out_le32(&hsdev.sata_dwc_regs->errmr, SATA_DWC_SERROR_ERR_BITS); |
| |
| hsdev.host = ap.host; |
| memset(&hsdevp, 0, sizeof(hsdevp)); |
| hsdevp.hsdev = &hsdev; |
| |
| for (i = 0; i < SATA_DWC_QCMD_MAX; i++) |
| hsdevp.cmd_issued[i] = SATA_DWC_CMD_ISSUED_NOT; |
| |
| out_le32((void __iomem *)scr_addr_sstatus + 4, |
| in_le32((void __iomem *)scr_addr_sstatus + 4)); |
| |
| rc = 0; |
| return rc; |
| } |
| |
| static u8 ata_check_altstatus(struct ata_port *ap) |
| { |
| u8 val = 0; |
| val = readb(ap->ioaddr.altstatus_addr); |
| return val; |
| } |
| |
| static int sata_dwc_softreset(struct ata_port *ap) |
| { |
| u8 nsect,lbal = 0; |
| u8 tmp = 0; |
| struct ata_ioports *ioaddr = &ap->ioaddr; |
| |
| in_le32((void *)ap->ioaddr.scr_addr + (SCR_ERROR * 4)); |
| |
| writeb(0x55, ioaddr->nsect_addr); |
| writeb(0xaa, ioaddr->lbal_addr); |
| writeb(0xaa, ioaddr->nsect_addr); |
| writeb(0x55, ioaddr->lbal_addr); |
| writeb(0x55, ioaddr->nsect_addr); |
| writeb(0xaa, ioaddr->lbal_addr); |
| |
| nsect = readb(ioaddr->nsect_addr); |
| lbal = readb(ioaddr->lbal_addr); |
| |
| if ((nsect == 0x55) && (lbal == 0xaa)) { |
| printf("Device found\n"); |
| } else { |
| printf("No device found\n"); |
| dev_state = SATA_NODEVICE; |
| return FALSE; |
| } |
| |
| tmp = ATA_DEVICE_OBS; |
| writeb(tmp, ioaddr->device_addr); |
| writeb(ap->ctl, ioaddr->ctl_addr); |
| |
| udelay(200); |
| |
| writeb(ap->ctl | ATA_SRST, ioaddr->ctl_addr); |
| |
| udelay(200); |
| writeb(ap->ctl, ioaddr->ctl_addr); |
| |
| msleep(150); |
| ata_check_status(ap); |
| |
| msleep(50); |
| ata_check_status(ap); |
| |
| while (1) { |
| u8 status = ata_check_status(ap); |
| |
| if (!(status & ATA_BUSY)) |
| break; |
| |
| printf("Hard Disk status is BUSY.\n"); |
| msleep(50); |
| } |
| |
| tmp = ATA_DEVICE_OBS; |
| writeb(tmp, ioaddr->device_addr); |
| |
| nsect = readb(ioaddr->nsect_addr); |
| lbal = readb(ioaddr->lbal_addr); |
| |
| return 0; |
| } |
| |
| static u8 ata_check_status(struct ata_port *ap) |
| { |
| u8 val = 0; |
| val = readb(ap->ioaddr.status_addr); |
| return val; |
| } |
| |
| static int ata_id_has_hipm(const u16 *id) |
| { |
| u16 val = id[76]; |
| |
| if (val == 0 || val == 0xffff) |
| return -1; |
| |
| return val & (1 << 9); |
| } |
| |
| static int ata_id_has_dipm(const u16 *id) |
| { |
| u16 val = id[78]; |
| |
| if (val == 0 || val == 0xffff) |
| return -1; |
| |
| return val & (1 << 3); |
| } |
| |
| int scan_sata(int dev) |
| { |
| int i; |
| int rc; |
| u8 status; |
| const u16 *id; |
| struct ata_device *ata_dev = &ata_device; |
| unsigned long pio_mask, mwdma_mask; |
| char revbuf[7]; |
| u16 iobuf[ATA_SECTOR_WORDS]; |
| |
| memset(iobuf, 0, sizeof(iobuf)); |
| |
| if (dev_state == SATA_NODEVICE) |
| return 1; |
| |
| printf("Waiting for device..."); |
| i = 0; |
| while (1) { |
| udelay(10000); |
| |
| status = ata_check_altstatus(&ap); |
| |
| if ((status & ATA_BUSY) == 0) { |
| printf("\n"); |
| break; |
| } |
| |
| i++; |
| if (i > (ATA_RESET_TIME * 100)) { |
| printf("** TimeOUT **\n"); |
| |
| dev_state = SATA_NODEVICE; |
| return 1; |
| } |
| if ((i >= 100) && ((i % 100) == 0)) |
| printf("."); |
| } |
| |
| udelay(1000); |
| |
| rc = ata_dev_read_id(ata_dev, &ata_dev->class, |
| ATA_READID_POSTRESET,ata_dev->id); |
| if (rc) { |
| printf("sata_dwc : error. failed sata scan\n"); |
| return 1; |
| } |
| |
| /* SATA drives indicate we have a bridge. We don't know which |
| * end of the link the bridge is which is a problem |
| */ |
| if (ata_id_is_sata(ata_dev->id)) |
| ap.cbl = ATA_CBL_SATA; |
| |
| id = ata_dev->id; |
| |
| ata_dev->flags &= ~ATA_DFLAG_CFG_MASK; |
| ata_dev->max_sectors = 0; |
| ata_dev->cdb_len = 0; |
| ata_dev->n_sectors = 0; |
| ata_dev->cylinders = 0; |
| ata_dev->heads = 0; |
| ata_dev->sectors = 0; |
| |
| if (id[ATA_ID_FIELD_VALID] & (1 << 1)) { |
| pio_mask = id[ATA_ID_PIO_MODES] & 0x03; |
| pio_mask <<= 3; |
| pio_mask |= 0x7; |
| } else { |
| /* If word 64 isn't valid then Word 51 high byte holds |
| * the PIO timing number for the maximum. Turn it into |
| * a mask. |
| */ |
| u8 mode = (id[ATA_ID_OLD_PIO_MODES] >> 8) & 0xFF; |
| if (mode < 5) { |
| pio_mask = (2 << mode) - 1; |
| } else { |
| pio_mask = 1; |
| } |
| } |
| |
| mwdma_mask = id[ATA_ID_MWDMA_MODES] & 0x07; |
| |
| if (ata_id_is_cfa(id)) { |
| int pio = id[163] & 0x7; |
| int dma = (id[163] >> 3) & 7; |
| |
| if (pio) |
| pio_mask |= (1 << 5); |
| if (pio > 1) |
| pio_mask |= (1 << 6); |
| if (dma) |
| mwdma_mask |= (1 << 3); |
| if (dma > 1) |
| mwdma_mask |= (1 << 4); |
| } |
| |
| if (ata_dev->class == ATA_DEV_ATA) { |
| if (ata_id_is_cfa(id)) { |
| if (id[162] & 1) |
| printf("supports DRM functions and may " |
| "not be fully accessable.\n"); |
| sprintf(revbuf, "%s", "CFA"); |
| } else { |
| if (ata_id_has_tpm(id)) |
| printf("supports DRM functions and may " |
| "not be fully accessable.\n"); |
| } |
| |
| ata_dev->n_sectors = ata_id_n_sectors((u16*)id); |
| |
| if (ata_dev->id[59] & 0x100) |
| ata_dev->multi_count = ata_dev->id[59] & 0xff; |
| |
| if (ata_id_has_lba(id)) { |
| char ncq_desc[20]; |
| |
| ata_dev->flags |= ATA_DFLAG_LBA; |
| if (ata_id_has_lba48(id)) { |
| ata_dev->flags |= ATA_DFLAG_LBA48; |
| |
| if (ata_dev->n_sectors >= (1UL << 28) && |
| ata_id_has_flush_ext(id)) |
| ata_dev->flags |= ATA_DFLAG_FLUSH_EXT; |
| } |
| if (!ata_id_has_ncq(ata_dev->id)) |
| ncq_desc[0] = '\0'; |
| |
| if (ata_dev->horkage & ATA_HORKAGE_NONCQ) |
| sprintf(ncq_desc, "%s", "NCQ (not used)"); |
| |
| if (ap.flags & ATA_FLAG_NCQ) |
| ata_dev->flags |= ATA_DFLAG_NCQ; |
| } |
| ata_dev->cdb_len = 16; |
| } |
| ata_dev->max_sectors = ATA_MAX_SECTORS; |
| if (ata_dev->flags & ATA_DFLAG_LBA48) |
| ata_dev->max_sectors = ATA_MAX_SECTORS_LBA48; |
| |
| if (!(ata_dev->horkage & ATA_HORKAGE_IPM)) { |
| if (ata_id_has_hipm(ata_dev->id)) |
| ata_dev->flags |= ATA_DFLAG_HIPM; |
| if (ata_id_has_dipm(ata_dev->id)) |
| ata_dev->flags |= ATA_DFLAG_DIPM; |
| } |
| |
| if ((ap.cbl == ATA_CBL_SATA) && (!ata_id_is_sata(ata_dev->id))) { |
| ata_dev->udma_mask &= ATA_UDMA5; |
| ata_dev->max_sectors = ATA_MAX_SECTORS; |
| } |
| |
| if (ata_dev->horkage & ATA_HORKAGE_DIAGNOSTIC) { |
| printf("Drive reports diagnostics failure." |
| "This may indicate a drive\n"); |
| printf("fault or invalid emulation." |
| "Contact drive vendor for information.\n"); |
| } |
| |
| rc = check_sata_dev_state(); |
| |
| ata_id_c_string(ata_dev->id, |
| (unsigned char *)sata_dev_desc[dev].revision, |
| ATA_ID_FW_REV, sizeof(sata_dev_desc[dev].revision)); |
| ata_id_c_string(ata_dev->id, |
| (unsigned char *)sata_dev_desc[dev].vendor, |
| ATA_ID_PROD, sizeof(sata_dev_desc[dev].vendor)); |
| ata_id_c_string(ata_dev->id, |
| (unsigned char *)sata_dev_desc[dev].product, |
| ATA_ID_SERNO, sizeof(sata_dev_desc[dev].product)); |
| |
| sata_dev_desc[dev].lba = (u32) ata_dev->n_sectors; |
| |
| #ifdef CONFIG_LBA48 |
| if (ata_dev->id[83] & (1 << 10)) { |
| sata_dev_desc[dev].lba48 = 1; |
| } else { |
| sata_dev_desc[dev].lba48 = 0; |
| } |
| #endif |
| |
| return 0; |
| } |
| |
| static u8 ata_busy_wait(struct ata_port *ap, |
| unsigned int bits,unsigned int max) |
| { |
| u8 status; |
| |
| do { |
| udelay(10); |
| status = ata_check_status(ap); |
| max--; |
| } while (status != 0xff && (status & bits) && (max > 0)); |
| |
| return status; |
| } |
| |
| static int ata_dev_read_id(struct ata_device *dev, unsigned int *p_class, |
| unsigned int flags, u16 *id) |
| { |
| struct ata_port *ap = pap; |
| unsigned int class = *p_class; |
| struct ata_taskfile tf; |
| unsigned int err_mask = 0; |
| const char *reason; |
| int may_fallback = 1, tried_spinup = 0; |
| u8 status; |
| int rc; |
| |
| status = ata_busy_wait(ap, ATA_BUSY, 30000); |
| if (status & ATA_BUSY) { |
| printf("BSY = 0 check. timeout.\n"); |
| rc = FALSE; |
| return rc; |
| } |
| |
| ata_dev_select(ap, dev->devno, 1, 1); |
| |
| retry: |
| memset(&tf, 0, sizeof(tf)); |
| ap->print_id = 1; |
| ap->flags &= ~ATA_FLAG_DISABLED; |
| tf.ctl = ap->ctl; |
| tf.device = ATA_DEVICE_OBS; |
| tf.command = ATA_CMD_ID_ATA; |
| tf.protocol = ATA_PROT_PIO; |
| |
| /* Some devices choke if TF registers contain garbage. Make |
| * sure those are properly initialized. |
| */ |
| tf.flags |= ATA_TFLAG_ISADDR | ATA_TFLAG_DEVICE; |
| |
| /* Device presence detection is unreliable on some |
| * controllers. Always poll IDENTIFY if available. |
| */ |
| tf.flags |= ATA_TFLAG_POLLING; |
| |
| temp_n_block = 1; |
| |
| err_mask = ata_exec_internal(dev, &tf, NULL, DMA_FROM_DEVICE, |
| sizeof(id[0]) * ATA_ID_WORDS, 0); |
| |
| if (err_mask) { |
| if (err_mask & AC_ERR_NODEV_HINT) { |
| printf("NODEV after polling detection\n"); |
| return -ENOENT; |
| } |
| |
| if ((err_mask == AC_ERR_DEV) && (tf.feature & ATA_ABORTED)) { |
| /* Device or controller might have reported |
| * the wrong device class. Give a shot at the |
| * other IDENTIFY if the current one is |
| * aborted by the device. |
| */ |
| if (may_fallback) { |
| may_fallback = 0; |
| |
| if (class == ATA_DEV_ATA) { |
| class = ATA_DEV_ATAPI; |
| } else { |
| class = ATA_DEV_ATA; |
| } |
| goto retry; |
| } |
| /* Control reaches here iff the device aborted |
| * both flavors of IDENTIFYs which happens |
| * sometimes with phantom devices. |
| */ |
| printf("both IDENTIFYs aborted, assuming NODEV\n"); |
| return -ENOENT; |
| } |
| rc = -EIO; |
| reason = "I/O error"; |
| goto err_out; |
| } |
| |
| /* Falling back doesn't make sense if ID data was read |
| * successfully at least once. |
| */ |
| may_fallback = 0; |
| |
| unsigned int id_cnt; |
| |
| for (id_cnt = 0; id_cnt < ATA_ID_WORDS; id_cnt++) |
| id[id_cnt] = le16_to_cpu(id[id_cnt]); |
| |
| |
| rc = -EINVAL; |
| reason = "device reports invalid type"; |
| |
| if (class == ATA_DEV_ATA) { |
| if (!ata_id_is_ata(id) && !ata_id_is_cfa(id)) |
| goto err_out; |
| } else { |
| if (ata_id_is_ata(id)) |
| goto err_out; |
| } |
| if (!tried_spinup && (id[2] == 0x37c8 || id[2] == 0x738c)) { |
| tried_spinup = 1; |
| /* |
| * Drive powered-up in standby mode, and requires a specific |
| * SET_FEATURES spin-up subcommand before it will accept |
| * anything other than the original IDENTIFY command. |
| */ |
| err_mask = ata_dev_set_feature(dev, SETFEATURES_SPINUP, 0); |
| if (err_mask && id[2] != 0x738c) { |
| rc = -EIO; |
| reason = "SPINUP failed"; |
| goto err_out; |
| } |
| /* |
| * If the drive initially returned incomplete IDENTIFY info, |
| * we now must reissue the IDENTIFY command. |
| */ |
| if (id[2] == 0x37c8) |
| goto retry; |
| } |
| |
| if ((flags & ATA_READID_POSTRESET) && class == ATA_DEV_ATA) { |
| /* |
| * The exact sequence expected by certain pre-ATA4 drives is: |
| * SRST RESET |
| * IDENTIFY (optional in early ATA) |
| * INITIALIZE DEVICE PARAMETERS (later IDE and ATA) |
| * anything else.. |
| * Some drives were very specific about that exact sequence. |
| * |
| * Note that ATA4 says lba is mandatory so the second check |
| * shoud never trigger. |
| */ |
| if (ata_id_major_version(id) < 4 || !ata_id_has_lba(id)) { |
| err_mask = ata_dev_init_params(dev, id[3], id[6]); |
| if (err_mask) { |
| rc = -EIO; |
| reason = "INIT_DEV_PARAMS failed"; |
| goto err_out; |
| } |
| |
| /* current CHS translation info (id[53-58]) might be |
| * changed. reread the identify device info. |
| */ |
| flags &= ~ATA_READID_POSTRESET; |
| goto retry; |
| } |
| } |
| |
| *p_class = class; |
| return 0; |
| |
| err_out: |
| printf("failed to READ ID (%s, err_mask=0x%x)\n", reason, err_mask); |
| return rc; |
| } |
| |
| static u8 ata_wait_idle(struct ata_port *ap) |
| { |
| u8 status = ata_busy_wait(ap, ATA_BUSY | ATA_DRQ, 1000); |
| return status; |
| } |
| |
| static void ata_dev_select(struct ata_port *ap, unsigned int device, |
| unsigned int wait, unsigned int can_sleep) |
| { |
| if (wait) |
| ata_wait_idle(ap); |
| |
| ata_std_dev_select(ap, device); |
| |
| if (wait) |
| ata_wait_idle(ap); |
| } |
| |
| static void ata_std_dev_select(struct ata_port *ap, unsigned int device) |
| { |
| u8 tmp; |
| |
| if (device == 0) { |
| tmp = ATA_DEVICE_OBS; |
| } else { |
| tmp = ATA_DEVICE_OBS | ATA_DEV1; |
| } |
| |
| writeb(tmp, ap->ioaddr.device_addr); |
| |
| readb(ap->ioaddr.altstatus_addr); |
| |
| udelay(1); |
| } |
| |
| static int waiting_for_reg_state(volatile u8 *offset, |
| int timeout_msec, |
| u32 sign) |
| { |
| int i; |
| u32 status; |
| |
| for (i = 0; i < timeout_msec; i++) { |
| status = readl(offset); |
| if ((status & sign) != 0) |
| break; |
| msleep(1); |
| } |
| |
| return (i < timeout_msec) ? 0 : -1; |
| } |
| |
| static void ata_qc_reinit(struct ata_queued_cmd *qc) |
| { |
| qc->dma_dir = DMA_NONE; |
| qc->flags = 0; |
| qc->nbytes = qc->extrabytes = qc->curbytes = 0; |
| qc->n_elem = 0; |
| qc->err_mask = 0; |
| qc->sect_size = ATA_SECT_SIZE; |
| qc->nbytes = ATA_SECT_SIZE * temp_n_block; |
| |
| memset(&qc->tf, 0, sizeof(qc->tf)); |
| qc->tf.ctl = 0; |
| qc->tf.device = ATA_DEVICE_OBS; |
| |
| qc->result_tf.command = ATA_DRDY; |
| qc->result_tf.feature = 0; |
| } |
| |
| struct ata_queued_cmd *__ata_qc_from_tag(struct ata_port *ap, |
| unsigned int tag) |
| { |
| if (tag < ATA_MAX_QUEUE) |
| return &ap->qcmd[tag]; |
| return NULL; |
| } |
| |
| static void __ata_port_freeze(struct ata_port *ap) |
| { |
| printf("set port freeze.\n"); |
| ap->pflags |= ATA_PFLAG_FROZEN; |
| } |
| |
| static int ata_port_freeze(struct ata_port *ap) |
| { |
| __ata_port_freeze(ap); |
| return 0; |
| } |
| |
| unsigned ata_exec_internal(struct ata_device *dev, |
| struct ata_taskfile *tf, const u8 *cdb, |
| int dma_dir, unsigned int buflen, |
| unsigned long timeout) |
| { |
| struct ata_link *link = dev->link; |
| struct ata_port *ap = pap; |
| struct ata_queued_cmd *qc; |
| unsigned int tag, preempted_tag; |
| u32 preempted_sactive, preempted_qc_active; |
| int preempted_nr_active_links; |
| unsigned int err_mask; |
| int rc = 0; |
| u8 status; |
| |
| status = ata_busy_wait(ap, ATA_BUSY, 300000); |
| if (status & ATA_BUSY) { |
| printf("BSY = 0 check. timeout.\n"); |
| rc = FALSE; |
| return rc; |
| } |
| |
| if (ap->pflags & ATA_PFLAG_FROZEN) |
| return AC_ERR_SYSTEM; |
| |
| tag = ATA_TAG_INTERNAL; |
| |
| if (test_and_set_bit(tag, &ap->qc_allocated)) { |
| rc = FALSE; |
| return rc; |
| } |
| |
| qc = __ata_qc_from_tag(ap, tag); |
| qc->tag = tag; |
| qc->ap = ap; |
| qc->dev = dev; |
| |
| ata_qc_reinit(qc); |
| |
| preempted_tag = link->active_tag; |
| preempted_sactive = link->sactive; |
| preempted_qc_active = ap->qc_active; |
| preempted_nr_active_links = ap->nr_active_links; |
| link->active_tag = ATA_TAG_POISON; |
| link->sactive = 0; |
| ap->qc_active = 0; |
| ap->nr_active_links = 0; |
| |
| qc->tf = *tf; |
| if (cdb) |
| memcpy(qc->cdb, cdb, ATAPI_CDB_LEN); |
| qc->flags |= ATA_QCFLAG_RESULT_TF; |
| qc->dma_dir = dma_dir; |
| qc->private_data = 0; |
| |
| ata_qc_issue(qc); |
| |
| if (!timeout) |
| timeout = ata_probe_timeout * 1000 / HZ; |
| |
| status = ata_busy_wait(ap, ATA_BUSY, 30000); |
| if (status & ATA_BUSY) { |
| printf("BSY = 0 check. timeout.\n"); |
| printf("altstatus = 0x%x.\n", status); |
| qc->err_mask |= AC_ERR_OTHER; |
| return qc->err_mask; |
| } |
| |
| if (waiting_for_reg_state(ap->ioaddr.altstatus_addr, 1000, 0x8)) { |
| u8 status = 0; |
| u8 errorStatus = 0; |
| |
| status = readb(ap->ioaddr.altstatus_addr); |
| if ((status & 0x01) != 0) { |
| errorStatus = readb(ap->ioaddr.feature_addr); |
| if (errorStatus == 0x04 && |
| qc->tf.command == ATA_CMD_PIO_READ_EXT){ |
| printf("Hard Disk doesn't support LBA48\n"); |
| dev_state = SATA_ERROR; |
| qc->err_mask |= AC_ERR_OTHER; |
| return qc->err_mask; |
| } |
| } |
| qc->err_mask |= AC_ERR_OTHER; |
| return qc->err_mask; |
| } |
| |
| status = ata_busy_wait(ap, ATA_BUSY, 10); |
| if (status & ATA_BUSY) { |
| printf("BSY = 0 check. timeout.\n"); |
| qc->err_mask |= AC_ERR_OTHER; |
| return qc->err_mask; |
| } |
| |
| ata_pio_task(ap); |
| |
| if (!rc) { |
| if (qc->flags & ATA_QCFLAG_ACTIVE) { |
| qc->err_mask |= AC_ERR_TIMEOUT; |
| ata_port_freeze(ap); |
| } |
| } |
| |
| if (qc->flags & ATA_QCFLAG_FAILED) { |
| if (qc->result_tf.command & (ATA_ERR | ATA_DF)) |
| qc->err_mask |= AC_ERR_DEV; |
| |
| if (!qc->err_mask) |
| qc->err_mask |= AC_ERR_OTHER; |
| |
| if (qc->err_mask & ~AC_ERR_OTHER) |
| qc->err_mask &= ~AC_ERR_OTHER; |
| } |
| |
| *tf = qc->result_tf; |
| err_mask = qc->err_mask; |
| ata_qc_free(qc); |
| link->active_tag = preempted_tag; |
| link->sactive = preempted_sactive; |
| ap->qc_active = preempted_qc_active; |
| ap->nr_active_links = preempted_nr_active_links; |
| |
| if (ap->flags & ATA_FLAG_DISABLED) { |
| err_mask |= AC_ERR_SYSTEM; |
| ap->flags &= ~ATA_FLAG_DISABLED; |
| } |
| |
| return err_mask; |
| } |
| |
| static void ata_qc_issue(struct ata_queued_cmd *qc) |
| { |
| struct ata_port *ap = qc->ap; |
| struct ata_link *link = qc->dev->link; |
| u8 prot = qc->tf.protocol; |
| |
| if (ata_is_ncq(prot)) { |
| if (!link->sactive) |
| ap->nr_active_links++; |
| link->sactive |= 1 << qc->tag; |
| } else { |
| ap->nr_active_links++; |
| link->active_tag = qc->tag; |
| } |
| |
| qc->flags |= ATA_QCFLAG_ACTIVE; |
| ap->qc_active |= 1 << qc->tag; |
| |
| if (qc->dev->flags & ATA_DFLAG_SLEEPING) { |
| msleep(1); |
| return; |
| } |
| |
| qc->err_mask |= ata_qc_issue_prot(qc); |
| if (qc->err_mask) |
| goto err; |
| |
| return; |
| err: |
| ata_qc_complete(qc); |
| } |
| |
| static unsigned int ata_qc_issue_prot(struct ata_queued_cmd *qc) |
| { |
| struct ata_port *ap = qc->ap; |
| |
| if (ap->flags & ATA_FLAG_PIO_POLLING) { |
| switch (qc->tf.protocol) { |
| case ATA_PROT_PIO: |
| case ATA_PROT_NODATA: |
| case ATAPI_PROT_PIO: |
| case ATAPI_PROT_NODATA: |
| qc->tf.flags |= ATA_TFLAG_POLLING; |
| break; |
| default: |
| break; |
| } |
| } |
| |
| ata_dev_select(ap, qc->dev->devno, 1, 0); |
| |
| switch (qc->tf.protocol) { |
| case ATA_PROT_PIO: |
| if (qc->tf.flags & ATA_TFLAG_POLLING) |
| qc->tf.ctl |= ATA_NIEN; |
| |
| ata_tf_to_host(ap, &qc->tf); |
| |
| ap->hsm_task_state = HSM_ST; |
| |
| if (qc->tf.flags & ATA_TFLAG_POLLING) |
| ata_pio_queue_task(ap, qc, 0); |
| |
| break; |
| |
| default: |
| return AC_ERR_SYSTEM; |
| } |
| |
| return 0; |
| } |
| |
| static void ata_tf_to_host(struct ata_port *ap, |
| const struct ata_taskfile *tf) |
| { |
| ata_tf_load(ap, tf); |
| ata_exec_command(ap, tf); |
| } |
| |
| static void ata_tf_load(struct ata_port *ap, |
| const struct ata_taskfile *tf) |
| { |
| struct ata_ioports *ioaddr = &ap->ioaddr; |
| unsigned int is_addr = tf->flags & ATA_TFLAG_ISADDR; |
| |
| if (tf->ctl != ap->last_ctl) { |
| if (ioaddr->ctl_addr) |
| writeb(tf->ctl, ioaddr->ctl_addr); |
| ap->last_ctl = tf->ctl; |
| ata_wait_idle(ap); |
| } |
| |
| if (is_addr && (tf->flags & ATA_TFLAG_LBA48)) { |
| writeb(tf->hob_feature, ioaddr->feature_addr); |
| writeb(tf->hob_nsect, ioaddr->nsect_addr); |
| writeb(tf->hob_lbal, ioaddr->lbal_addr); |
| writeb(tf->hob_lbam, ioaddr->lbam_addr); |
| writeb(tf->hob_lbah, ioaddr->lbah_addr); |
| } |
| |
| if (is_addr) { |
| writeb(tf->feature, ioaddr->feature_addr); |
| writeb(tf->nsect, ioaddr->nsect_addr); |
| writeb(tf->lbal, ioaddr->lbal_addr); |
| writeb(tf->lbam, ioaddr->lbam_addr); |
| writeb(tf->lbah, ioaddr->lbah_addr); |
| } |
| |
| if (tf->flags & ATA_TFLAG_DEVICE) |
| writeb(tf->device, ioaddr->device_addr); |
| |
| ata_wait_idle(ap); |
| } |
| |
| static void ata_exec_command(struct ata_port *ap, |
| const struct ata_taskfile *tf) |
| { |
| writeb(tf->command, ap->ioaddr.command_addr); |
| |
| readb(ap->ioaddr.altstatus_addr); |
| |
| udelay(1); |
| } |
| |
| static void ata_pio_queue_task(struct ata_port *ap, |
| void *data,unsigned long delay) |
| { |
| ap->port_task_data = data; |
| } |
| |
| static unsigned int ac_err_mask(u8 status) |
| { |
| if (status & (ATA_BUSY | ATA_DRQ)) |
| return AC_ERR_HSM; |
| if (status & (ATA_ERR | ATA_DF)) |
| return AC_ERR_DEV; |
| return 0; |
| } |
| |
| static unsigned int __ac_err_mask(u8 status) |
| { |
| unsigned int mask = ac_err_mask(status); |
| if (mask == 0) |
| return AC_ERR_OTHER; |
| return mask; |
| } |
| |
| static void ata_pio_task(struct ata_port *arg_ap) |
| { |
| struct ata_port *ap = arg_ap; |
| struct ata_queued_cmd *qc = ap->port_task_data; |
| u8 status; |
| int poll_next; |
| |
| fsm_start: |
| /* |
| * This is purely heuristic. This is a fast path. |
| * Sometimes when we enter, BSY will be cleared in |
| * a chk-status or two. If not, the drive is probably seeking |
| * or something. Snooze for a couple msecs, then |
| * chk-status again. If still busy, queue delayed work. |
| */ |
| status = ata_busy_wait(ap, ATA_BUSY, 5); |
| if (status & ATA_BUSY) { |
| msleep(2); |
| status = ata_busy_wait(ap, ATA_BUSY, 10); |
| if (status & ATA_BUSY) { |
| ata_pio_queue_task(ap, qc, ATA_SHORT_PAUSE); |
| return; |
| } |
| } |
| |
| poll_next = ata_hsm_move(ap, qc, status, 1); |
| |
| /* another command or interrupt handler |
| * may be running at this point. |
| */ |
| if (poll_next) |
| goto fsm_start; |
| } |
| |
| static int ata_hsm_move(struct ata_port *ap, struct ata_queued_cmd *qc, |
| u8 status, int in_wq) |
| { |
| int poll_next; |
| |
| fsm_start: |
| switch (ap->hsm_task_state) { |
| case HSM_ST_FIRST: |
| poll_next = (qc->tf.flags & ATA_TFLAG_POLLING); |
| |
| if ((status & ATA_DRQ) == 0) { |
| if (status & (ATA_ERR | ATA_DF)) { |
| qc->err_mask |= AC_ERR_DEV; |
| } else { |
| qc->err_mask |= AC_ERR_HSM; |
| } |
| ap->hsm_task_state = HSM_ST_ERR; |
| goto fsm_start; |
| } |
| |
| /* Device should not ask for data transfer (DRQ=1) |
| * when it finds something wrong. |
| * We ignore DRQ here and stop the HSM by |
| * changing hsm_task_state to HSM_ST_ERR and |
| * let the EH abort the command or reset the device. |
| */ |
| if (status & (ATA_ERR | ATA_DF)) { |
| if (!(qc->dev->horkage & ATA_HORKAGE_STUCK_ERR)) { |
| printf("DRQ=1 with device error, " |
| "dev_stat 0x%X\n", status); |
| qc->err_mask |= AC_ERR_HSM; |
| ap->hsm_task_state = HSM_ST_ERR; |
| goto fsm_start; |
| } |
| } |
| |
| if (qc->tf.protocol == ATA_PROT_PIO) { |
| /* PIO data out protocol. |
| * send first data block. |
| */ |
| /* ata_pio_sectors() might change the state |
| * to HSM_ST_LAST. so, the state is changed here |
| * before ata_pio_sectors(). |
| */ |
| ap->hsm_task_state = HSM_ST; |
| ata_pio_sectors(qc); |
| } else { |
| printf("protocol is not ATA_PROT_PIO \n"); |
| } |
| break; |
| |
| case HSM_ST: |
| if ((status & ATA_DRQ) == 0) { |
| if (status & (ATA_ERR | ATA_DF)) { |
| qc->err_mask |= AC_ERR_DEV; |
| } else { |
| /* HSM violation. Let EH handle this. |
| * Phantom devices also trigger this |
| * condition. Mark hint. |
| */ |
| qc->err_mask |= AC_ERR_HSM | AC_ERR_NODEV_HINT; |
| } |
| |
| ap->hsm_task_state = HSM_ST_ERR; |
| goto fsm_start; |
| } |
| /* For PIO reads, some devices may ask for |
| * data transfer (DRQ=1) alone with ERR=1. |
| * We respect DRQ here and transfer one |
| * block of junk data before changing the |
| * hsm_task_state to HSM_ST_ERR. |
| * |
| * For PIO writes, ERR=1 DRQ=1 doesn't make |
| * sense since the data block has been |
| * transferred to the device. |
| */ |
| if (status & (ATA_ERR | ATA_DF)) { |
| qc->err_mask |= AC_ERR_DEV; |
| |
| if (!(qc->tf.flags & ATA_TFLAG_WRITE)) { |
| ata_pio_sectors(qc); |
| status = ata_wait_idle(ap); |
| } |
| |
| if (status & (ATA_BUSY | ATA_DRQ)) |
| qc->err_mask |= AC_ERR_HSM; |
| |
| /* ata_pio_sectors() might change the |
| * state to HSM_ST_LAST. so, the state |
| * is changed after ata_pio_sectors(). |
| */ |
| ap->hsm_task_state = HSM_ST_ERR; |
| goto fsm_start; |
| } |
| |
| ata_pio_sectors(qc); |
| if (ap->hsm_task_state == HSM_ST_LAST && |
| (!(qc->tf.flags & ATA_TFLAG_WRITE))) { |
| status = ata_wait_idle(ap); |
| goto fsm_start; |
| } |
| |
| poll_next = 1; |
| break; |
| |
| case HSM_ST_LAST: |
| if (!ata_ok(status)) { |
| qc->err_mask |= __ac_err_mask(status); |
| ap->hsm_task_state = HSM_ST_ERR; |
| goto fsm_start; |
| } |
| |
| ap->hsm_task_state = HSM_ST_IDLE; |
| |
| ata_hsm_qc_complete(qc, in_wq); |
| |
| poll_next = 0; |
| break; |
| |
| case HSM_ST_ERR: |
| /* make sure qc->err_mask is available to |
| * know what's wrong and recover |
| */ |
| ap->hsm_task_state = HSM_ST_IDLE; |
| |
| ata_hsm_qc_complete(qc, in_wq); |
| |
| poll_next = 0; |
| break; |
| default: |
| poll_next = 0; |
| } |
| |
| return poll_next; |
| } |
| |
| static void ata_pio_sectors(struct ata_queued_cmd *qc) |
| { |
| struct ata_port *ap; |
| ap = pap; |
| qc->pdata = ap->pdata; |
| |
| ata_pio_sector(qc); |
| |
| readb(qc->ap->ioaddr.altstatus_addr); |
| udelay(1); |
| } |
| |
| static void ata_pio_sector(struct ata_queued_cmd *qc) |
| { |
| int do_write = (qc->tf.flags & ATA_TFLAG_WRITE); |
| struct ata_port *ap = qc->ap; |
| unsigned int offset; |
| unsigned char *buf; |
| char temp_data_buf[512]; |
| |
| if (qc->curbytes == qc->nbytes - qc->sect_size) |
| ap->hsm_task_state = HSM_ST_LAST; |
| |
| offset = qc->curbytes; |
| |
| switch (qc->tf.command) { |
| case ATA_CMD_ID_ATA: |
| buf = (unsigned char *)&ata_device.id[0]; |
| break; |
| case ATA_CMD_PIO_READ_EXT: |
| case ATA_CMD_PIO_READ: |
| case ATA_CMD_PIO_WRITE_EXT: |
| case ATA_CMD_PIO_WRITE: |
| buf = qc->pdata + offset; |
| break; |
| default: |
| buf = (unsigned char *)&temp_data_buf[0]; |
| } |
| |
| ata_mmio_data_xfer(qc->dev, buf, qc->sect_size, do_write); |
| |
| qc->curbytes += qc->sect_size; |
| |
| } |
| |
| static void ata_mmio_data_xfer(struct ata_device *dev, unsigned char *buf, |
| unsigned int buflen, int do_write) |
| { |
| struct ata_port *ap = pap; |
| void __iomem *data_addr = ap->ioaddr.data_addr; |
| unsigned int words = buflen >> 1; |
| u16 *buf16 = (u16 *)buf; |
| unsigned int i = 0; |
| |
| udelay(100); |
| if (do_write) { |
| for (i = 0; i < words; i++) |
| writew(le16_to_cpu(buf16[i]), data_addr); |
| } else { |
| for (i = 0; i < words; i++) |
| buf16[i] = cpu_to_le16(readw(data_addr)); |
| } |
| |
| if (buflen & 0x01) { |
| __le16 align_buf[1] = { 0 }; |
| unsigned char *trailing_buf = buf + buflen - 1; |
| |
| if (do_write) { |
| memcpy(align_buf, trailing_buf, 1); |
| writew(le16_to_cpu(align_buf[0]), data_addr); |
| } else { |
| align_buf[0] = cpu_to_le16(readw(data_addr)); |
| memcpy(trailing_buf, align_buf, 1); |
| } |
| } |
| } |
| |
| static void ata_hsm_qc_complete(struct ata_queued_cmd *qc, int in_wq) |
| { |
| struct ata_port *ap = qc->ap; |
| |
| if (in_wq) { |
| /* EH might have kicked in while host lock is |
| * released. |
| */ |
| qc = &ap->qcmd[qc->tag]; |
| if (qc) { |
| if (!(qc->err_mask & AC_ERR_HSM)) { |
| ata_irq_on(ap); |
| ata_qc_complete(qc); |
| } else { |
| ata_port_freeze(ap); |
| } |
| } |
| } else { |
| if (!(qc->err_mask & AC_ERR_HSM)) { |
| ata_qc_complete(qc); |
| } else { |
| ata_port_freeze(ap); |
| } |
| } |
| } |
| |
| static u8 ata_irq_on(struct ata_port *ap) |
| { |
| struct ata_ioports *ioaddr = &ap->ioaddr; |
| u8 tmp; |
| |
| ap->ctl &= ~ATA_NIEN; |
| ap->last_ctl = ap->ctl; |
| |
| if (ioaddr->ctl_addr) |
| writeb(ap->ctl, ioaddr->ctl_addr); |
| |
| tmp = ata_wait_idle(ap); |
| |
| return tmp; |
| } |
| |
| static unsigned int ata_tag_internal(unsigned int tag) |
| { |
| return tag == ATA_MAX_QUEUE - 1; |
| } |
| |
| static void ata_qc_complete(struct ata_queued_cmd *qc) |
| { |
| struct ata_device *dev = qc->dev; |
| if (qc->err_mask) |
| qc->flags |= ATA_QCFLAG_FAILED; |
| |
| if (qc->flags & ATA_QCFLAG_FAILED) { |
| if (!ata_tag_internal(qc->tag)) { |
| fill_result_tf(qc); |
| return; |
| } |
| } |
| if (qc->flags & ATA_QCFLAG_RESULT_TF) |
| fill_result_tf(qc); |
| |
| /* Some commands need post-processing after successful |
| * completion. |
| */ |
| switch (qc->tf.command) { |
| case ATA_CMD_SET_FEATURES: |
| if (qc->tf.feature != SETFEATURES_WC_ON && |
| qc->tf.feature != SETFEATURES_WC_OFF) |
| break; |
| case ATA_CMD_INIT_DEV_PARAMS: |
| case ATA_CMD_SET_MULTI: |
| break; |
| |
| case ATA_CMD_SLEEP: |
| dev->flags |= ATA_DFLAG_SLEEPING; |
| break; |
| } |
| |
| __ata_qc_complete(qc); |
| } |
| |
| static void fill_result_tf(struct ata_queued_cmd *qc) |
| { |
| struct ata_port *ap = qc->ap; |
| |
| qc->result_tf.flags = qc->tf.flags; |
| ata_tf_read(ap, &qc->result_tf); |
| } |
| |
| static void ata_tf_read(struct ata_port *ap, struct ata_taskfile *tf) |
| { |
| struct ata_ioports *ioaddr = &ap->ioaddr; |
| |
| tf->command = ata_check_status(ap); |
| tf->feature = readb(ioaddr->error_addr); |
| tf->nsect = readb(ioaddr->nsect_addr); |
| tf->lbal = readb(ioaddr->lbal_addr); |
| tf->lbam = readb(ioaddr->lbam_addr); |
| tf->lbah = readb(ioaddr->lbah_addr); |
| tf->device = readb(ioaddr->device_addr); |
| |
| if (tf->flags & ATA_TFLAG_LBA48) { |
| if (ioaddr->ctl_addr) { |
| writeb(tf->ctl | ATA_HOB, ioaddr->ctl_addr); |
| |
| tf->hob_feature = readb(ioaddr->error_addr); |
| tf->hob_nsect = readb(ioaddr->nsect_addr); |
| tf->hob_lbal = readb(ioaddr->lbal_addr); |
| tf->hob_lbam = readb(ioaddr->lbam_addr); |
| tf->hob_lbah = readb(ioaddr->lbah_addr); |
| |
| writeb(tf->ctl, ioaddr->ctl_addr); |
| ap->last_ctl = tf->ctl; |
| } else { |
| printf("sata_dwc warnning register read.\n"); |
| } |
| } |
| } |
| |
| static void __ata_qc_complete(struct ata_queued_cmd *qc) |
| { |
| struct ata_port *ap = qc->ap; |
| struct ata_link *link = qc->dev->link; |
| |
| link->active_tag = ATA_TAG_POISON; |
| ap->nr_active_links--; |
| |
| if (qc->flags & ATA_QCFLAG_CLEAR_EXCL && ap->excl_link == link) |
| ap->excl_link = NULL; |
| |
| qc->flags &= ~ATA_QCFLAG_ACTIVE; |
| ap->qc_active &= ~(1 << qc->tag); |
| } |
| |
| static void ata_qc_free(struct ata_queued_cmd *qc) |
| { |
| struct ata_port *ap = qc->ap; |
| unsigned int tag; |
| qc->flags = 0; |
| tag = qc->tag; |
| if (tag < ATA_MAX_QUEUE) { |
| qc->tag = ATA_TAG_POISON; |
| clear_bit(tag, &ap->qc_allocated); |
| } |
| } |
| |
| static int check_sata_dev_state(void) |
| { |
| unsigned long datalen; |
| unsigned char *pdata; |
| int ret = 0; |
| int i = 0; |
| char temp_data_buf[512]; |
| |
| while (1) { |
| udelay(10000); |
| |
| pdata = (unsigned char*)&temp_data_buf[0]; |
| datalen = 512; |
| |
| ret = ata_dev_read_sectors(pdata, datalen, 0, 1); |
| |
| if (ret == TRUE) |
| break; |
| |
| i++; |
| if (i > (ATA_RESET_TIME * 100)) { |
| printf("** TimeOUT **\n"); |
| dev_state = SATA_NODEVICE; |
| return FALSE; |
| } |
| |
| if ((i >= 100) && ((i % 100) == 0)) |
| printf("."); |
| } |
| |
| dev_state = SATA_READY; |
| |
| return TRUE; |
| } |
| |
| static unsigned int ata_dev_set_feature(struct ata_device *dev, |
| u8 enable, u8 feature) |
| { |
| struct ata_taskfile tf; |
| struct ata_port *ap; |
| ap = pap; |
| unsigned int err_mask; |
| |
| memset(&tf, 0, sizeof(tf)); |
| tf.ctl = ap->ctl; |
| |
| tf.device = ATA_DEVICE_OBS; |
| tf.command = ATA_CMD_SET_FEATURES; |
| tf.feature = enable; |
| tf.flags |= ATA_TFLAG_ISADDR | ATA_TFLAG_DEVICE; |
| tf.protocol = ATA_PROT_NODATA; |
| tf.nsect = feature; |
| |
| err_mask = ata_exec_internal(dev, &tf, NULL, DMA_NONE, 0, 0); |
| |
| return err_mask; |
| } |
| |
| static unsigned int ata_dev_init_params(struct ata_device *dev, |
| u16 heads, u16 sectors) |
| { |
| struct ata_taskfile tf; |
| struct ata_port *ap; |
| ap = pap; |
| unsigned int err_mask; |
| |
| if (sectors < 1 || sectors > 255 || heads < 1 || heads > 16) |
| return AC_ERR_INVALID; |
| |
| memset(&tf, 0, sizeof(tf)); |
| tf.ctl = ap->ctl; |
| tf.device = ATA_DEVICE_OBS; |
| tf.command = ATA_CMD_INIT_DEV_PARAMS; |
| tf.flags |= ATA_TFLAG_ISADDR | ATA_TFLAG_DEVICE; |
| tf.protocol = ATA_PROT_NODATA; |
| tf.nsect = sectors; |
| tf.device |= (heads - 1) & 0x0f; |
| |
| err_mask = ata_exec_internal(dev, &tf, NULL, DMA_NONE, 0, 0); |
| |
| if (err_mask == AC_ERR_DEV && (tf.feature & ATA_ABORTED)) |
| err_mask = 0; |
| |
| return err_mask; |
| } |
| |
| #if defined(CONFIG_SATA_DWC) && !defined(CONFIG_LBA48) |
| #define SATA_MAX_READ_BLK 0xFF |
| #else |
| #define SATA_MAX_READ_BLK 0xFFFF |
| #endif |
| |
| ulong sata_read(int device, ulong blknr, lbaint_t blkcnt, void *buffer) |
| { |
| ulong start,blks, buf_addr; |
| unsigned short smallblks; |
| unsigned long datalen; |
| unsigned char *pdata; |
| device &= 0xff; |
| |
| u32 block = 0; |
| u32 n_block = 0; |
| |
| if (dev_state != SATA_READY) |
| return 0; |
| |
| buf_addr = (unsigned long)buffer; |
| start = blknr; |
| blks = blkcnt; |
| do { |
| pdata = (unsigned char *)buf_addr; |
| if (blks > SATA_MAX_READ_BLK) { |
| datalen = sata_dev_desc[device].blksz * SATA_MAX_READ_BLK; |
| smallblks = SATA_MAX_READ_BLK; |
| |
| block = (u32)start; |
| n_block = (u32)smallblks; |
| |
| start += SATA_MAX_READ_BLK; |
| blks -= SATA_MAX_READ_BLK; |
| } else { |
| datalen = sata_dev_desc[device].blksz * SATA_MAX_READ_BLK; |
| datalen = sata_dev_desc[device].blksz * blks; |
| smallblks = (unsigned short)blks; |
| |
| block = (u32)start; |
| n_block = (u32)smallblks; |
| |
| start += blks; |
| blks = 0; |
| } |
| |
| if (ata_dev_read_sectors(pdata, datalen, block, n_block) != TRUE) { |
| printf("sata_dwc : Hard disk read error.\n"); |
| blkcnt -= blks; |
| break; |
| } |
| buf_addr += datalen; |
| } while (blks != 0); |
| |
| return (blkcnt); |
| } |
| |
| static int ata_dev_read_sectors(unsigned char *pdata, unsigned long datalen, |
| u32 block, u32 n_block) |
| { |
| struct ata_port *ap = pap; |
| struct ata_device *dev = &ata_device; |
| struct ata_taskfile tf; |
| unsigned int class = ATA_DEV_ATA; |
| unsigned int err_mask = 0; |
| const char *reason; |
| int may_fallback = 1; |
| |
| if (dev_state == SATA_ERROR) |
| return FALSE; |
| |
| ata_dev_select(ap, dev->devno, 1, 1); |
| |
| retry: |
| memset(&tf, 0, sizeof(tf)); |
| tf.ctl = ap->ctl; |
| ap->print_id = 1; |
| ap->flags &= ~ATA_FLAG_DISABLED; |
| |
| ap->pdata = pdata; |
| |
| tf.device = ATA_DEVICE_OBS; |
| |
| temp_n_block = n_block; |
| |
| #ifdef CONFIG_LBA48 |
| tf.command = ATA_CMD_PIO_READ_EXT; |
| tf.flags |= ATA_TFLAG_LBA | ATA_TFLAG_LBA48; |
| |
| tf.hob_feature = 31; |
| tf.feature = 31; |
| tf.hob_nsect = (n_block >> 8) & 0xff; |
| tf.nsect = n_block & 0xff; |
| |
| tf.hob_lbah = 0x0; |
| tf.hob_lbam = 0x0; |
| tf.hob_lbal = (block >> 24) & 0xff; |
| tf.lbah = (block >> 16) & 0xff; |
| tf.lbam = (block >> 8) & 0xff; |
| tf.lbal = block & 0xff; |
| |
| tf.device = 1 << 6; |
| if (tf.flags & ATA_TFLAG_FUA) |
| tf.device |= 1 << 7; |
| #else |
| tf.command = ATA_CMD_PIO_READ; |
| tf.flags |= ATA_TFLAG_LBA ; |
| |
| tf.feature = 31; |
| tf.nsect = n_block & 0xff; |
| |
| tf.lbah = (block >> 16) & 0xff; |
| tf.lbam = (block >> 8) & 0xff; |
| tf.lbal = block & 0xff; |
| |
| tf.device = (block >> 24) & 0xf; |
| |
| tf.device |= 1 << 6; |
| if (tf.flags & ATA_TFLAG_FUA) |
| tf.device |= 1 << 7; |
| |
| #endif |
| |
| tf.protocol = ATA_PROT_PIO; |
| |
| /* Some devices choke if TF registers contain garbage. Make |
| * sure those are properly initialized. |
| */ |
| tf.flags |= ATA_TFLAG_ISADDR | ATA_TFLAG_DEVICE; |
| tf.flags |= ATA_TFLAG_POLLING; |
| |
| err_mask = ata_exec_internal(dev, &tf, NULL, DMA_FROM_DEVICE, 0, 0); |
| |
| if (err_mask) { |
| if (err_mask & AC_ERR_NODEV_HINT) { |
| printf("READ_SECTORS NODEV after polling detection\n"); |
| return -ENOENT; |
| } |
| |
| if ((err_mask == AC_ERR_DEV) && (tf.feature & ATA_ABORTED)) { |
| /* Device or controller might have reported |
| * the wrong device class. Give a shot at the |
| * other IDENTIFY if the current one is |
| * aborted by the device. |
| */ |
| if (may_fallback) { |
| may_fallback = 0; |
| |
| if (class == ATA_DEV_ATA) { |
| class = ATA_DEV_ATAPI; |
| } else { |
| class = ATA_DEV_ATA; |
| } |
| goto retry; |
| } |
| /* Control reaches here iff the device aborted |
| * both flavors of IDENTIFYs which happens |
| * sometimes with phantom devices. |
| */ |
| printf("both IDENTIFYs aborted, assuming NODEV\n"); |
| return -ENOENT; |
| } |
| |
| reason = "I/O error"; |
| goto err_out; |
| } |
| |
| return TRUE; |
| |
| err_out: |
| printf("failed to READ SECTORS (%s, err_mask=0x%x)\n", reason, err_mask); |
| return FALSE; |
| } |
| |
| #if defined(CONFIG_SATA_DWC) && !defined(CONFIG_LBA48) |
| #define SATA_MAX_WRITE_BLK 0xFF |
| #else |
| #define SATA_MAX_WRITE_BLK 0xFFFF |
| #endif |
| |
| ulong sata_write(int device, ulong blknr, lbaint_t blkcnt, void *buffer) |
| { |
| ulong start,blks, buf_addr; |
| unsigned short smallblks; |
| unsigned long datalen; |
| unsigned char *pdata; |
| device &= 0xff; |
| |
| |
| u32 block = 0; |
| u32 n_block = 0; |
| |
| if (dev_state != SATA_READY) |
| return 0; |
| |
| buf_addr = (unsigned long)buffer; |
| start = blknr; |
| blks = blkcnt; |
| do { |
| pdata = (unsigned char *)buf_addr; |
| if (blks > SATA_MAX_WRITE_BLK) { |
| datalen = sata_dev_desc[device].blksz * SATA_MAX_WRITE_BLK; |
| smallblks = SATA_MAX_WRITE_BLK; |
| |
| block = (u32)start; |
| n_block = (u32)smallblks; |
| |
| start += SATA_MAX_WRITE_BLK; |
| blks -= SATA_MAX_WRITE_BLK; |
| } else { |
| datalen = sata_dev_desc[device].blksz * blks; |
| smallblks = (unsigned short)blks; |
| |
| block = (u32)start; |
| n_block = (u32)smallblks; |
| |
| start += blks; |
| blks = 0; |
| } |
| |
| if (ata_dev_write_sectors(pdata, datalen, block, n_block) != TRUE) { |
| printf("sata_dwc : Hard disk read error.\n"); |
| blkcnt -= blks; |
| break; |
| } |
| buf_addr += datalen; |
| } while (blks != 0); |
| |
| return (blkcnt); |
| } |
| |
| static int ata_dev_write_sectors(unsigned char* pdata, unsigned long datalen, |
| u32 block, u32 n_block) |
| { |
| struct ata_port *ap = pap; |
| struct ata_device *dev = &ata_device; |
| struct ata_taskfile tf; |
| unsigned int class = ATA_DEV_ATA; |
| unsigned int err_mask = 0; |
| const char *reason; |
| int may_fallback = 1; |
| |
| if (dev_state == SATA_ERROR) |
| return FALSE; |
| |
| ata_dev_select(ap, dev->devno, 1, 1); |
| |
| retry: |
| memset(&tf, 0, sizeof(tf)); |
| tf.ctl = ap->ctl; |
| ap->print_id = 1; |
| ap->flags &= ~ATA_FLAG_DISABLED; |
| |
| ap->pdata = pdata; |
| |
| tf.device = ATA_DEVICE_OBS; |
| |
| temp_n_block = n_block; |
| |
| |
| #ifdef CONFIG_LBA48 |
| tf.command = ATA_CMD_PIO_WRITE_EXT; |
| tf.flags |= ATA_TFLAG_LBA | ATA_TFLAG_LBA48 | ATA_TFLAG_WRITE; |
| |
| tf.hob_feature = 31; |
| tf.feature = 31; |
| tf.hob_nsect = (n_block >> 8) & 0xff; |
| tf.nsect = n_block & 0xff; |
| |
| tf.hob_lbah = 0x0; |
| tf.hob_lbam = 0x0; |
| tf.hob_lbal = (block >> 24) & 0xff; |
| tf.lbah = (block >> 16) & 0xff; |
| tf.lbam = (block >> 8) & 0xff; |
| tf.lbal = block & 0xff; |
| |
| tf.device = 1 << 6; |
| if (tf.flags & ATA_TFLAG_FUA) |
| tf.device |= 1 << 7; |
| #else |
| tf.command = ATA_CMD_PIO_WRITE; |
| tf.flags |= ATA_TFLAG_LBA | ATA_TFLAG_WRITE; |
| |
| tf.feature = 31; |
| tf.nsect = n_block & 0xff; |
| |
| tf.lbah = (block >> 16) & 0xff; |
| tf.lbam = (block >> 8) & 0xff; |
| tf.lbal = block & 0xff; |
| |
| tf.device = (block >> 24) & 0xf; |
| |
| tf.device |= 1 << 6; |
| if (tf.flags & ATA_TFLAG_FUA) |
| tf.device |= 1 << 7; |
| |
| #endif |
| |
| tf.protocol = ATA_PROT_PIO; |
| |
| /* Some devices choke if TF registers contain garbage. Make |
| * sure those are properly initialized. |
| */ |
| tf.flags |= ATA_TFLAG_ISADDR | ATA_TFLAG_DEVICE; |
| tf.flags |= ATA_TFLAG_POLLING; |
| |
| err_mask = ata_exec_internal(dev, &tf, NULL, DMA_FROM_DEVICE, 0, 0); |
| |
| if (err_mask) { |
| if (err_mask & AC_ERR_NODEV_HINT) { |
| printf("READ_SECTORS NODEV after polling detection\n"); |
| return -ENOENT; |
| } |
| |
| if ((err_mask == AC_ERR_DEV) && (tf.feature & ATA_ABORTED)) { |
| /* Device or controller might have reported |
| * the wrong device class. Give a shot at the |
| * other IDENTIFY if the current one is |
| * aborted by the device. |
| */ |
| if (may_fallback) { |
| may_fallback = 0; |
| |
| if (class == ATA_DEV_ATA) { |
| class = ATA_DEV_ATAPI; |
| } else { |
| class = ATA_DEV_ATA; |
| } |
| goto retry; |
| } |
| /* Control reaches here iff the device aborted |
| * both flavors of IDENTIFYs which happens |
| * sometimes with phantom devices. |
| */ |
| printf("both IDENTIFYs aborted, assuming NODEV\n"); |
| return -ENOENT; |
| } |
| |
| reason = "I/O error"; |
| goto err_out; |
| } |
| |
| return TRUE; |
| |
| err_out: |
| printf("failed to WRITE SECTORS (%s, err_mask=0x%x)\n", reason, err_mask); |
| return FALSE; |
| } |