board/czechlight/clearfog/patches/linux.patch

diff --git a/Documentation/devicetree/bindings/mtd/fsl-quadspi.txt b/Documentation/devicetree/bindings/mtd/fsl-quadspi.txt
deleted file mode 100644
index 483e9cfac1b1..000000000000
--- a/Documentation/devicetree/bindings/mtd/fsl-quadspi.txt
+++ /dev/null
@@ -1,65 +0,0 @@
-* Freescale Quad Serial Peripheral Interface(QuadSPI)
-
-Required properties:
-  - compatible : Should be "fsl,vf610-qspi", "fsl,imx6sx-qspi",
-		 "fsl,imx7d-qspi", "fsl,imx6ul-qspi",
-		 "fsl,ls1021a-qspi"
-		 or
-		 "fsl,ls2080a-qspi" followed by "fsl,ls1021a-qspi",
-		 "fsl,ls1043a-qspi" followed by "fsl,ls1021a-qspi"
-  - reg : the first contains the register location and length,
-          the second contains the memory mapping address and length
-  - reg-names: Should contain the reg names "QuadSPI" and "QuadSPI-memory"
-  - interrupts : Should contain the interrupt for the device
-  - clocks : The clocks needed by the QuadSPI controller
-  - clock-names : Should contain the name of the clocks: "qspi_en" and "qspi".
-
-Optional properties:
-  - fsl,qspi-has-second-chip: The controller has two buses, bus A and bus B.
-                              Each bus can be connected with two NOR flashes.
-			      Most of the time, each bus only has one NOR flash
-			      connected, this is the default case.
-			      But if there are two NOR flashes connected to the
-			      bus, you should enable this property.
-			      (Please check the board's schematic.)
-  - big-endian : That means the IP register is big endian
-
-Example:
-
-qspi0: quadspi@40044000 {
-	compatible = "fsl,vf610-qspi";
-	reg = <0x40044000 0x1000>, <0x20000000 0x10000000>;
-	reg-names = "QuadSPI", "QuadSPI-memory";
-	interrupts = <0 24 IRQ_TYPE_LEVEL_HIGH>;
-	clocks = <&clks VF610_CLK_QSPI0_EN>,
-		<&clks VF610_CLK_QSPI0>;
-	clock-names = "qspi_en", "qspi";
-
-	flash0: s25fl128s@0 {
-		....
-	};
-};
-
-Example showing the usage of two SPI NOR devices:
-
-&qspi2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_qspi2>;
-	status = "okay";
-
-	flash0: n25q256a@0 {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		compatible = "micron,n25q256a", "jedec,spi-nor";
-		spi-max-frequency = <29000000>;
-		reg = <0>;
-	};
-
-	flash1: n25q256a@1 {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		compatible = "micron,n25q256a", "jedec,spi-nor";
-		spi-max-frequency = <29000000>;
-		reg = <1>;
-	};
-};
diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-mcp23s08.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-mcp23s08.txt
index 625a22e2f211..a0b1eb9aedad 100644
--- a/Documentation/devicetree/bindings/pinctrl/pinctrl-mcp23s08.txt
+++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-mcp23s08.txt
@@ -144,3 +144,38 @@ gpio21: gpio@21 {
 		bias-pull-up;
 	};
 };
+
+Line naming
+===========
+
+Because several gpio_chip instances are hidden below a single device tree
+node, it is necessary to split the names into several child nodes. Ensure
+that the configured addresses match those in the microchip,spi-present-mask:
+
+gpio@0 {
+	compatible = "microchip,mcp23s17";
+	gpio-controller;
+	#gpio-cells = <2>;
+	/* this bitmask has bits #0 (0x01) and #2 (0x04) set */
+	spi-present-mask = <0x05>;
+	reg = <0>;
+	spi-max-frequency = <1000000>;
+
+	gpio-bank@1 {
+		address = <0>;
+		gpio-line-names =
+			"GPA0",
+			"GPA1",
+			...
+			"GPA7",
+			"GPB0",
+			"GPB1",
+			...
+			"GPB7";
+	};
+
+	gpio-bank@2 {
+		address = <2>;
+		gpio-line-names = ...
+	};
+};
diff --git a/Documentation/devicetree/bindings/spi/atmel-quadspi.txt b/Documentation/devicetree/bindings/spi/atmel-quadspi.txt
index b93c1e2f25dd..7c40ea694352 100644
--- a/Documentation/devicetree/bindings/spi/atmel-quadspi.txt
+++ b/Documentation/devicetree/bindings/spi/atmel-quadspi.txt
@@ -1,14 +1,19 @@
 * Atmel Quad Serial Peripheral Interface (QSPI)
 
 Required properties:
-- compatible:     Should be "atmel,sama5d2-qspi".
+- compatible:     Should be one of the following:
+		  - "atmel,sama5d2-qspi"
+		  - "microchip,sam9x60-qspi"
 - reg:            Should contain the locations and lengths of the base registers
                   and the mapped memory.
 - reg-names:      Should contain the resource reg names:
                   - qspi_base: configuration register address space
                   - qspi_mmap: memory mapped address space
 - interrupts:     Should contain the interrupt for the device.
-- clocks:         The phandle of the clock needed by the QSPI controller.
+- clocks:         Should reference the peripheral clock and the QSPI system
+                  clock if available.
+- clock-names:    Should contain "pclk" for the peripheral clock and "qspick"
+                  for the system clock when available.
 - #address-cells: Should be <1>.
 - #size-cells:    Should be <0>.
 
@@ -19,7 +24,8 @@ spi@f0020000 {
 	reg = <0xf0020000 0x100>, <0xd0000000 0x8000000>;
 	reg-names = "qspi_base", "qspi_mmap";
 	interrupts = <52 IRQ_TYPE_LEVEL_HIGH 7>;
-	clocks = <&spi0_clk>;
+	clocks = <&pmc PMC_TYPE_PERIPHERAL 52>;
+	clock-names = "pclk";
 	#address-cells = <1>;
 	#size-cells = <0>;
 	pinctrl-names = "default";
diff --git a/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt b/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt
index e3c48b20b1a6..2d3264140cc5 100644
--- a/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt
+++ b/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt
@@ -10,6 +10,7 @@ Required properties:
   - "fsl,imx35-cspi" for SPI compatible with the one integrated on i.MX35
   - "fsl,imx51-ecspi" for SPI compatible with the one integrated on i.MX51
   - "fsl,imx53-ecspi" for SPI compatible with the one integrated on i.MX53 and later Soc
+  - "fsl,imx8mq-ecspi" for SPI compatible with the one integrated on i.MX8M
 - reg : Offset and length of the register set for the device
 - interrupts : Should contain CSPI/eCSPI interrupt
 - clocks : Clock specifiers for both ipg and per clocks.
diff --git a/Documentation/devicetree/bindings/spi/spi-fsl-qspi.txt b/Documentation/devicetree/bindings/spi/spi-fsl-qspi.txt
new file mode 100644
index 000000000000..e8f1d627d288
--- /dev/null
+++ b/Documentation/devicetree/bindings/spi/spi-fsl-qspi.txt
@@ -0,0 +1,63 @@
+* Freescale Quad Serial Peripheral Interface(QuadSPI)
+
+Required properties:
+  - compatible : Should be "fsl,vf610-qspi", "fsl,imx6sx-qspi",
+		 "fsl,imx7d-qspi", "fsl,imx6ul-qspi",
+		 "fsl,ls1021a-qspi"
+		 or
+		 "fsl,ls2080a-qspi" followed by "fsl,ls1021a-qspi",
+		 "fsl,ls1043a-qspi" followed by "fsl,ls1021a-qspi"
+  - reg : the first contains the register location and length,
+          the second contains the memory mapping address and length
+  - reg-names: Should contain the reg names "QuadSPI" and "QuadSPI-memory"
+  - interrupts : Should contain the interrupt for the device
+  - clocks : The clocks needed by the QuadSPI controller
+  - clock-names : Should contain the name of the clocks: "qspi_en" and "qspi".
+
+Required SPI slave node properties:
+  - reg: There are two buses (A and B) with two chip selects each.
+	 This encodes to which bus and CS the flash is connected:
+		<0>: Bus A, CS 0
+		<1>: Bus A, CS 1
+		<2>: Bus B, CS 0
+		<3>: Bus B, CS 1
+
+Example:
+
+qspi0: quadspi@40044000 {
+	compatible = "fsl,vf610-qspi";
+	reg = <0x40044000 0x1000>, <0x20000000 0x10000000>;
+	reg-names = "QuadSPI", "QuadSPI-memory";
+	interrupts = <0 24 IRQ_TYPE_LEVEL_HIGH>;
+	clocks = <&clks VF610_CLK_QSPI0_EN>,
+		<&clks VF610_CLK_QSPI0>;
+	clock-names = "qspi_en", "qspi";
+
+	flash0: s25fl128s@0 {
+		....
+	};
+};
+
+Example showing the usage of two SPI NOR devices on bus A:
+
+&qspi2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_qspi2>;
+	status = "okay";
+
+	flash0: n25q256a@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "micron,n25q256a", "jedec,spi-nor";
+		spi-max-frequency = <29000000>;
+		reg = <0>;
+	};
+
+	flash1: n25q256a@1 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "micron,n25q256a", "jedec,spi-nor";
+		spi-max-frequency = <29000000>;
+		reg = <1>;
+	};
+};
diff --git a/Documentation/devicetree/bindings/spi/spi-nxp-fspi.txt b/Documentation/devicetree/bindings/spi/spi-nxp-fspi.txt
new file mode 100644
index 000000000000..2cd67eb727d4
--- /dev/null
+++ b/Documentation/devicetree/bindings/spi/spi-nxp-fspi.txt
@@ -0,0 +1,39 @@
+* NXP Flex Serial Peripheral Interface (FSPI)
+
+Required properties:
+  - compatible : Should be "nxp,lx2160a-fspi"
+  - reg :        First contains the register location and length,
+                 Second contains the memory mapping address and length
+  - reg-names :  Should contain the resource reg names:
+	         - fspi_base: configuration register address space
+                 - fspi_mmap: memory mapped address space
+  - interrupts : Should contain the interrupt for the device
+
+Required SPI slave node properties:
+  - reg :        There are two buses (A and B) with two chip selects each.
+                 This encodes to which bus and CS the flash is connected:
+                 - <0>: Bus A, CS 0
+                 - <1>: Bus A, CS 1
+                 - <2>: Bus B, CS 0
+                 - <3>: Bus B, CS 1
+
+Example showing the usage of two SPI NOR slave devices on bus A:
+
+fspi0: spi@20c0000 {
+	compatible = "nxp,lx2160a-fspi";
+	reg = <0x0 0x20c0000 0x0 0x10000>, <0x0 0x20000000 0x0 0x10000000>;
+	reg-names = "fspi_base", "fspi_mmap";
+	interrupts = <0 25 0x4>; /* Level high type */
+	clocks = <&clockgen 4 3>, <&clockgen 4 3>;
+	clock-names = "fspi_en", "fspi";
+
+	mt35xu512aba0: flash@0 {
+		reg = <0>;
+		....
+	};
+
+	mt35xu512aba1: flash@1 {
+		reg = <1>;
+		....
+	};
+};
diff --git a/Documentation/devicetree/bindings/spi/spi-sifive.txt b/Documentation/devicetree/bindings/spi/spi-sifive.txt
new file mode 100644
index 000000000000..3f5c6e438972
--- /dev/null
+++ b/Documentation/devicetree/bindings/spi/spi-sifive.txt
@@ -0,0 +1,37 @@
+SiFive SPI controller Device Tree Bindings
+------------------------------------------
+
+Required properties:
+- compatible		: Should be "sifive,<chip>-spi" and "sifive,spi<version>".
+			  Supported compatible strings are:
+			  "sifive,fu540-c000-spi" for the SiFive SPI v0 as integrated
+			  onto the SiFive FU540 chip, and "sifive,spi0" for the SiFive
+			  SPI v0 IP block with no chip integration tweaks.
+			  Please refer to sifive-blocks-ip-versioning.txt for details
+- reg			: Physical base address and size of SPI registers map
+			  A second (optional) range can indicate memory mapped flash
+- interrupts		: Must contain one entry
+- interrupt-parent	: Must be core interrupt controller
+- clocks		: Must reference the frequency given to the controller
+- #address-cells	: Must be '1', indicating which CS to use
+- #size-cells		: Must be '0'
+
+Optional properties:
+- sifive,fifo-depth		: Depth of hardware queues; defaults to 8
+- sifive,max-bits-per-word	: Maximum bits per word; defaults to 8
+
+SPI RTL that corresponds to the IP block version numbers can be found here:
+https://github.com/sifive/sifive-blocks/tree/master/src/main/scala/devices/spi
+
+Example:
+	spi: spi@10040000 {
+		compatible = "sifive,fu540-c000-spi", "sifive,spi0";
+		reg = <0x0 0x10040000 0x0 0x1000 0x0 0x20000000 0x0 0x10000000>;
+		interrupt-parent = <&plic>;
+		interrupts = <51>;
+		clocks = <&tlclk>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		sifive,fifo-depth = <8>;
+		sifive,max-bits-per-word = <8>;
+	};
diff --git a/Documentation/devicetree/bindings/spi/spi-sprd.txt b/Documentation/devicetree/bindings/spi/spi-sprd.txt
index bad211a19da4..3c7eacce0ee3 100644
--- a/Documentation/devicetree/bindings/spi/spi-sprd.txt
+++ b/Documentation/devicetree/bindings/spi/spi-sprd.txt
@@ -14,6 +14,11 @@ Required properties:
 	address on the SPI bus. Should be set to 1.
 - #size-cells: Should be set to 0.
 
+Optional properties:
+dma-names: Should contain names of the SPI used DMA channel.
+dmas: Should contain DMA channels and DMA slave ids which the SPI used
+	sorted in the same order as the dma-names property.
+
 Example:
 spi0: spi@70a00000{
 	compatible = "sprd,sc9860-spi";
@@ -21,6 +26,8 @@ spi0: spi@70a00000{
 	interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
 	clock-names = "spi", "source","enable";
 	clocks = <&clk_spi0>, <&ext_26m>, <&clk_ap_apb_gates 5>;
+	dma-names = "rx_chn", "tx_chn";
+	dmas = <&apdma 11 11>, <&apdma 12 12>;
 	#address-cells = <1>;
 	#size-cells = <0>;
 };
diff --git a/Documentation/devicetree/bindings/spi/spi-stm32.txt b/Documentation/devicetree/bindings/spi/spi-stm32.txt
index 1b3fa2c119d5..d82755c63eaf 100644
--- a/Documentation/devicetree/bindings/spi/spi-stm32.txt
+++ b/Documentation/devicetree/bindings/spi/spi-stm32.txt
@@ -7,7 +7,9 @@ from 4 to 32-bit data size. Although it can be configured as master or slave,
 only master is supported by the driver.
 
 Required properties:
-- compatible: Must be "st,stm32h7-spi".
+- compatible: Should be one of:
+  "st,stm32h7-spi"
+  "st,stm32f4-spi"
 - reg: Offset and length of the device's register set.
 - interrupts: Must contain the interrupt id.
 - clocks: Must contain an entry for spiclk (which feeds the internal clock
@@ -30,8 +32,9 @@ Child nodes represent devices on the SPI bus
   See ../spi/spi-bus.txt
 
 Optional properties:
-- st,spi-midi-ns: (Master Inter-Data Idleness) minimum time delay in
-		  nanoseconds inserted between two consecutive data frames.
+- st,spi-midi-ns: Only for STM32H7, (Master Inter-Data Idleness) minimum time
+		  delay in nanoseconds inserted between two consecutive data
+		  frames.
 
 
 Example:
diff --git a/Documentation/spi/pxa2xx b/Documentation/spi/pxa2xx
index 13a0b7fb192f..551325b66b23 100644
--- a/Documentation/spi/pxa2xx
+++ b/Documentation/spi/pxa2xx
@@ -21,15 +21,15 @@ Typically a SPI master is defined in the arch/.../mach-*/board-*.c as a
 "platform device".  The master configuration is passed to the driver via a table
 found in include/linux/spi/pxa2xx_spi.h:
 
-struct pxa2xx_spi_master {
+struct pxa2xx_spi_controller {
 	u16 num_chipselect;
 	u8 enable_dma;
 };
 
-The "pxa2xx_spi_master.num_chipselect" field is used to determine the number of
+The "pxa2xx_spi_controller.num_chipselect" field is used to determine the number of
 slave device (chips) attached to this SPI master.
 
-The "pxa2xx_spi_master.enable_dma" field informs the driver that SSP DMA should
+The "pxa2xx_spi_controller.enable_dma" field informs the driver that SSP DMA should
 be used.  This caused the driver to acquire two DMA channels: rx_channel and
 tx_channel.  The rx_channel has a higher DMA service priority the tx_channel.
 See the "PXA2xx Developer Manual" section "DMA Controller".
@@ -51,7 +51,7 @@ static struct resource pxa_spi_nssp_resources[] = {
 	},
 };
 
-static struct pxa2xx_spi_master pxa_nssp_master_info = {
+static struct pxa2xx_spi_controller pxa_nssp_master_info = {
 	.num_chipselect = 1, /* Matches the number of chips attached to NSSP */
 	.enable_dma = 1, /* Enables NSSP DMA */
 };
@@ -206,7 +206,7 @@ DMA and PIO I/O Support
 -----------------------
 The pxa2xx_spi driver supports both DMA and interrupt driven PIO message
 transfers.  The driver defaults to PIO mode and DMA transfers must be enabled
-by setting the "enable_dma" flag in the "pxa2xx_spi_master" structure.  The DMA
+by setting the "enable_dma" flag in the "pxa2xx_spi_controller" structure.  The DMA
 mode supports both coherent and stream based DMA mappings.
 
 The following logic is used to determine the type of I/O to be used on
diff --git a/MAINTAINERS b/MAINTAINERS
index dce5c099f43c..ecb33bcc0ce4 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -6105,9 +6105,9 @@ F:	Documentation/devicetree/bindings/ptp/ptp-qoriq.txt
 
 FREESCALE QUAD SPI DRIVER
 M:	Han Xu <han.xu@nxp.com>
-L:	linux-mtd@lists.infradead.org
+L:	linux-spi@vger.kernel.org
 S:	Maintained
-F:	drivers/mtd/spi-nor/fsl-quadspi.c
+F:	drivers/spi/spi-fsl-qspi.c
 
 FREESCALE QUICC ENGINE LIBRARY
 M:	Qiang Zhao <qiang.zhao@nxp.com>
@@ -10944,6 +10944,14 @@ F:	lib/objagg.c
 F:	lib/test_objagg.c
 F:	include/linux/objagg.h
 
+NXP FSPI DRIVER
+R:	Yogesh Gaur <yogeshgaur.83@gmail.com>
+M:	Ashish Kumar <ashish.kumar@nxp.com>
+L:	linux-spi@vger.kernel.org
+S:	Maintained
+F:	drivers/spi/spi-nxp-fspi.c
+F:	Documentation/devicetree/bindings/spi/spi-nxp-fspi.txt
+
 OBJTOOL
 M:	Josh Poimboeuf <jpoimboe@redhat.com>
 M:	Peter Zijlstra <peterz@infradead.org>
diff --git a/arch/arm/mach-pxa/cm-x255.c b/arch/arm/mach-pxa/cm-x255.c
index fa8e7dd4d898..4401dfcd7e68 100644
--- a/arch/arm/mach-pxa/cm-x255.c
+++ b/arch/arm/mach-pxa/cm-x255.c
@@ -98,7 +98,7 @@ static unsigned long cmx255_pin_config[] = {
 };
 
 #if defined(CONFIG_SPI_PXA2XX)
-static struct pxa2xx_spi_master pxa_ssp_master_info = {
+static struct pxa2xx_spi_controller pxa_ssp_master_info = {
 	.num_chipselect	= 1,
 };
 
diff --git a/arch/arm/mach-pxa/cm-x270.c b/arch/arm/mach-pxa/cm-x270.c
index f7081a50dc67..279eeca7add0 100644
--- a/arch/arm/mach-pxa/cm-x270.c
+++ b/arch/arm/mach-pxa/cm-x270.c
@@ -313,7 +313,7 @@ static inline void cmx270_init_mmc(void) {}
 #endif
 
 #if defined(CONFIG_SPI_PXA2XX) || defined(CONFIG_SPI_PXA2XX_MODULE)
-static struct pxa2xx_spi_master cm_x270_spi_info = {
+static struct pxa2xx_spi_controller cm_x270_spi_info = {
 	.num_chipselect	= 1,
 	.enable_dma	= 1,
 };
diff --git a/arch/arm/mach-pxa/corgi.c b/arch/arm/mach-pxa/corgi.c
index c9732cace5e3..7ecf559bd71c 100644
--- a/arch/arm/mach-pxa/corgi.c
+++ b/arch/arm/mach-pxa/corgi.c
@@ -530,7 +530,7 @@ static struct pxa2xx_udc_mach_info udc_info __initdata = {
 };
 
 #if IS_ENABLED(CONFIG_SPI_PXA2XX)
-static struct pxa2xx_spi_master corgi_spi_info = {
+static struct pxa2xx_spi_controller corgi_spi_info = {
 	.num_chipselect	= 3,
 };
 
diff --git a/arch/arm/mach-pxa/devices.c b/arch/arm/mach-pxa/devices.c
index a24783a03827..524d6093e0c7 100644
--- a/arch/arm/mach-pxa/devices.c
+++ b/arch/arm/mach-pxa/devices.c
@@ -1065,7 +1065,7 @@ struct platform_device pxa93x_device_gpio = {
 
 /* pxa2xx-spi platform-device ID equals respective SSP platform-device ID + 1.
  * See comment in arch/arm/mach-pxa/ssp.c::ssp_probe() */
-void __init pxa2xx_set_spi_info(unsigned id, struct pxa2xx_spi_master *info)
+void __init pxa2xx_set_spi_info(unsigned id, struct pxa2xx_spi_controller *info)
 {
 	struct platform_device *pd;
 
diff --git a/arch/arm/mach-pxa/em-x270.c b/arch/arm/mach-pxa/em-x270.c
index 32c1edeb3f14..5e372760f16e 100644
--- a/arch/arm/mach-pxa/em-x270.c
+++ b/arch/arm/mach-pxa/em-x270.c
@@ -689,7 +689,7 @@ static inline void em_x270_init_lcd(void) {}
 #endif
 
 #if defined(CONFIG_SPI_PXA2XX) || defined(CONFIG_SPI_PXA2XX_MODULE)
-static struct pxa2xx_spi_master em_x270_spi_info = {
+static struct pxa2xx_spi_controller em_x270_spi_info = {
 	.num_chipselect	= 1,
 };
 
@@ -703,7 +703,7 @@ static struct tdo24m_platform_data em_x270_tdo24m_pdata = {
 	.model = TDO35S,
 };
 
-static struct pxa2xx_spi_master em_x270_spi_2_info = {
+static struct pxa2xx_spi_controller em_x270_spi_2_info = {
 	.num_chipselect	= 1,
 	.enable_dma	= 1,
 };
diff --git a/arch/arm/mach-pxa/hx4700.c b/arch/arm/mach-pxa/hx4700.c
index b79b757fdd41..c3b47557b3f2 100644
--- a/arch/arm/mach-pxa/hx4700.c
+++ b/arch/arm/mach-pxa/hx4700.c
@@ -629,7 +629,7 @@ static struct spi_board_info tsc2046_board_info[] __initdata = {
 	},
 };
 
-static struct pxa2xx_spi_master pxa_ssp2_master_info = {
+static struct pxa2xx_spi_controller pxa_ssp2_master_info = {
 	.num_chipselect = 1,
 	.enable_dma     = 1,
 };
diff --git a/arch/arm/mach-pxa/icontrol.c b/arch/arm/mach-pxa/icontrol.c
index cbaf4f6edcda..7e30452e3840 100644
--- a/arch/arm/mach-pxa/icontrol.c
+++ b/arch/arm/mach-pxa/icontrol.c
@@ -115,12 +115,12 @@ static struct spi_board_info mcp251x_board_info[] = {
 	}
 };
 
-static struct pxa2xx_spi_master pxa_ssp3_spi_master_info = {
+static struct pxa2xx_spi_controller pxa_ssp3_spi_master_info = {
 	.num_chipselect = 2,
 	.enable_dma     = 1
 };
 
-static struct pxa2xx_spi_master pxa_ssp4_spi_master_info = {
+static struct pxa2xx_spi_controller pxa_ssp4_spi_master_info = {
 	.num_chipselect = 2,
 	.enable_dma     = 1
 };
diff --git a/arch/arm/mach-pxa/littleton.c b/arch/arm/mach-pxa/littleton.c
index 39db4898dc4a..464b8bd2bcb9 100644
--- a/arch/arm/mach-pxa/littleton.c
+++ b/arch/arm/mach-pxa/littleton.c
@@ -191,7 +191,7 @@ static inline void littleton_init_lcd(void) {};
 #endif /* CONFIG_FB_PXA || CONFIG_FB_PXA_MODULE */
 
 #if defined(CONFIG_SPI_PXA2XX) || defined(CONFIG_SPI_PXA2XX_MODULE)
-static struct pxa2xx_spi_master littleton_spi_info = {
+static struct pxa2xx_spi_controller littleton_spi_info = {
 	.num_chipselect		= 1,
 };
 
diff --git a/arch/arm/mach-pxa/lubbock.c b/arch/arm/mach-pxa/lubbock.c
index a1391e113ef4..c1bd0d544981 100644
--- a/arch/arm/mach-pxa/lubbock.c
+++ b/arch/arm/mach-pxa/lubbock.c
@@ -197,7 +197,7 @@ static struct platform_device sa1111_device = {
  * (to J5) and poking board registers (as done below).  Else it's only useful
  * for the temperature sensors.
  */
-static struct pxa2xx_spi_master pxa_ssp_master_info = {
+static struct pxa2xx_spi_controller pxa_ssp_master_info = {
 	.num_chipselect	= 1,
 };
 
diff --git a/arch/arm/mach-pxa/magician.c b/arch/arm/mach-pxa/magician.c
index 08b079653c3f..618bcff4cdc9 100644
--- a/arch/arm/mach-pxa/magician.c
+++ b/arch/arm/mach-pxa/magician.c
@@ -932,7 +932,7 @@ struct pxa2xx_spi_chip tsc2046_chip_info = {
 	.gpio_cs	= GPIO14_MAGICIAN_TSC2046_CS,
 };
 
-static struct pxa2xx_spi_master magician_spi_info = {
+static struct pxa2xx_spi_controller magician_spi_info = {
 	.num_chipselect	= 1,
 	.enable_dma	= 1,
 };
diff --git a/arch/arm/mach-pxa/pcm027.c b/arch/arm/mach-pxa/pcm027.c
index ccca9f7575c3..e2e613449660 100644
--- a/arch/arm/mach-pxa/pcm027.c
+++ b/arch/arm/mach-pxa/pcm027.c
@@ -132,7 +132,7 @@ static struct platform_device smc91x_device = {
 /*
  * SPI host and devices
  */
-static struct pxa2xx_spi_master pxa_ssp_master_info = {
+static struct pxa2xx_spi_controller pxa_ssp_master_info = {
 	.num_chipselect	= 1,
 };
 
diff --git a/arch/arm/mach-pxa/poodle.c b/arch/arm/mach-pxa/poodle.c
index c2a43d4cfd3e..9450a523cd0b 100644
--- a/arch/arm/mach-pxa/poodle.c
+++ b/arch/arm/mach-pxa/poodle.c
@@ -196,7 +196,7 @@ struct platform_device poodle_locomo_device = {
 EXPORT_SYMBOL(poodle_locomo_device);
 
 #if defined(CONFIG_SPI_PXA2XX) || defined(CONFIG_SPI_PXA2XX_MODULE)
-static struct pxa2xx_spi_master poodle_spi_info = {
+static struct pxa2xx_spi_controller poodle_spi_info = {
 	.num_chipselect	= 1,
 };
 
diff --git a/arch/arm/mach-pxa/spitz.c b/arch/arm/mach-pxa/spitz.c
index 306818e2cf54..8dac824a85df 100644
--- a/arch/arm/mach-pxa/spitz.c
+++ b/arch/arm/mach-pxa/spitz.c
@@ -572,7 +572,7 @@ static struct spi_board_info spitz_spi_devices[] = {
 	},
 };
 
-static struct pxa2xx_spi_master spitz_spi_info = {
+static struct pxa2xx_spi_controller spitz_spi_info = {
 	.num_chipselect	= 3,
 };
 
diff --git a/arch/arm/mach-pxa/stargate2.c b/arch/arm/mach-pxa/stargate2.c
index e0d6c872270a..c28d19b126a7 100644
--- a/arch/arm/mach-pxa/stargate2.c
+++ b/arch/arm/mach-pxa/stargate2.c
@@ -337,15 +337,15 @@ static struct platform_device stargate2_flash_device = {
 	.num_resources = 1,
 };
 
-static struct pxa2xx_spi_master pxa_ssp_master_0_info = {
+static struct pxa2xx_spi_controller pxa_ssp_master_0_info = {
 	.num_chipselect = 1,
 };
 
-static struct pxa2xx_spi_master pxa_ssp_master_1_info = {
+static struct pxa2xx_spi_controller pxa_ssp_master_1_info = {
 	.num_chipselect = 1,
 };
 
-static struct pxa2xx_spi_master pxa_ssp_master_2_info = {
+static struct pxa2xx_spi_controller pxa_ssp_master_2_info = {
 	.num_chipselect = 1,
 };
 
diff --git a/arch/arm/mach-pxa/tosa.c b/arch/arm/mach-pxa/tosa.c
index e8a93c088c35..7439798d58e4 100644
--- a/arch/arm/mach-pxa/tosa.c
+++ b/arch/arm/mach-pxa/tosa.c
@@ -813,7 +813,7 @@ static struct platform_device tosa_bt_device = {
 	.dev.platform_data = &tosa_bt_data,
 };
 
-static struct pxa2xx_spi_master pxa_ssp_master_info = {
+static struct pxa2xx_spi_controller pxa_ssp_master_info = {
 	.num_chipselect	= 1,
 };
 
diff --git a/arch/arm/mach-pxa/z2.c b/arch/arm/mach-pxa/z2.c
index e2353e75bb28..ad082e11e2a4 100644
--- a/arch/arm/mach-pxa/z2.c
+++ b/arch/arm/mach-pxa/z2.c
@@ -607,12 +607,12 @@ static struct spi_board_info spi_board_info[] __initdata = {
 },
 };
 
-static struct pxa2xx_spi_master pxa_ssp1_master_info = {
+static struct pxa2xx_spi_controller pxa_ssp1_master_info = {
 	.num_chipselect	= 1,
 	.enable_dma	= 1,
 };
 
-static struct pxa2xx_spi_master pxa_ssp2_master_info = {
+static struct pxa2xx_spi_controller pxa_ssp2_master_info = {
 	.num_chipselect	= 1,
 };
 
diff --git a/arch/arm/mach-pxa/zeus.c b/arch/arm/mach-pxa/zeus.c
index c411f79d4cb5..bdbcf46595f9 100644
--- a/arch/arm/mach-pxa/zeus.c
+++ b/arch/arm/mach-pxa/zeus.c
@@ -391,7 +391,7 @@ static struct platform_device zeus_sram_device = {
 };
 
 /* SPI interface on SSP3 */
-static struct pxa2xx_spi_master pxa2xx_spi_ssp3_master_info = {
+static struct pxa2xx_spi_controller pxa2xx_spi_ssp3_master_info = {
 	.num_chipselect = 1,
 	.enable_dma     = 1,
 };
diff --git a/arch/mips/ath79/dev-spi.h b/arch/mips/ath79/dev-spi.h
index d732565ca736..6e15bc8651be 100644
--- a/arch/mips/ath79/dev-spi.h
+++ b/arch/mips/ath79/dev-spi.h
@@ -13,7 +13,7 @@
 #define _ATH79_DEV_SPI_H
 
 #include <linux/spi/spi.h>
-#include <asm/mach-ath79/ath79_spi_platform.h>
+#include <linux/platform_data/spi-ath79.h>
 
 void ath79_register_spi(struct ath79_spi_platform_data *pdata,
 			 struct spi_board_info const *info,
diff --git a/arch/mips/include/asm/mach-ath79/ath79_spi_platform.h b/arch/mips/include/asm/mach-ath79/ath79_spi_platform.h
deleted file mode 100644
index aa71216edf99..000000000000
--- a/arch/mips/include/asm/mach-ath79/ath79_spi_platform.h
+++ /dev/null
@@ -1,19 +0,0 @@
-/*
- *  Platform data definition for Atheros AR71XX/AR724X/AR913X SPI controller
- *
- *  Copyright (C) 2008-2010 Gabor Juhos <juhosg@openwrt.org>
- *
- *  This program is free software; you can redistribute it and/or modify it
- *  under the terms of the GNU General Public License version 2 as published
- *  by the Free Software Foundation.
- */
-
-#ifndef _ATH79_SPI_PLATFORM_H
-#define _ATH79_SPI_PLATFORM_H
-
-struct ath79_spi_platform_data {
-	unsigned	bus_num;
-	unsigned	num_chipselect;
-};
-
-#endif /* _ATH79_SPI_PLATFORM_H */
diff --git a/drivers/gpio/gpiolib-devprop.c b/drivers/gpio/gpiolib-devprop.c
index dd517098ab95..0c6f97c09bd9 100644
--- a/drivers/gpio/gpiolib-devprop.c
+++ b/drivers/gpio/gpiolib-devprop.c
@@ -56,3 +56,5 @@ void devprop_gpiochip_set_names(struct gpio_chip *chip,
 
 	kfree(names);
 }
+
+EXPORT_SYMBOL_GPL(devprop_gpiochip_set_names)
diff --git a/drivers/gpio/gpiolib-of.c b/drivers/gpio/gpiolib-of.c
index a6e1891217e2..c34eb9d9c59a 100644
--- a/drivers/gpio/gpiolib-of.c
+++ b/drivers/gpio/gpiolib-of.c
@@ -125,7 +125,7 @@ static void of_gpio_flags_quirks(struct device_node *np,
 
 		for_each_child_of_node(np, child) {
 			ret = of_property_read_u32(child, "reg", &cs);
-			if (!ret)
+			if (ret)
 				continue;
 			if (cs == index) {
 				/*
diff --git a/drivers/gpio/gpiolib.h b/drivers/gpio/gpiolib.h
index bc57f0dc5953..0c512900752d 100644
--- a/drivers/gpio/gpiolib.h
+++ b/drivers/gpio/gpiolib.h
@@ -241,9 +241,6 @@ static inline int gpio_chip_hwgpio(const struct gpio_desc *desc)
 	return desc - &desc->gdev->descs[0];
 }
 
-void devprop_gpiochip_set_names(struct gpio_chip *chip,
-				const struct fwnode_handle *fwnode);
-
 /* With descriptor prefix */
 
 #define gpiod_emerg(desc, fmt, ...)					       \
diff --git a/drivers/i2c/busses/i2c-mv64xxx.c b/drivers/i2c/busses/i2c-mv64xxx.c
index a5a95ea5b81a..469374ded7ae 100644
--- a/drivers/i2c/busses/i2c-mv64xxx.c
+++ b/drivers/i2c/busses/i2c-mv64xxx.c
@@ -317,6 +317,14 @@ mv64xxx_i2c_fsm(struct mv64xxx_i2c_data *drv_data, u32 status)
 		drv_data->rc = -ENXIO;
 		break;
 
+	case MV64XXX_I2C_STATUS_BUS_ERR: /* 0x00 */
+		dev_warn(&drv_data->adapter.dev,
+			 "bus error: slave has driven SDA/SCL unexpectedly\n");
+		drv_data->action = MV64XXX_I2C_ACTION_SEND_STOP;
+		mv64xxx_i2c_hw_init(drv_data);
+		drv_data->rc = -EIO;
+		break;
+
 	default:
 		dev_err(&drv_data->adapter.dev,
 			"mv64xxx_i2c_fsm: Ctlr Error -- state: 0x%x, "
diff --git a/drivers/leds/leds-tlc591xx.c b/drivers/leds/leds-tlc591xx.c
index f5357f6d9e58..efbe9c83c514 100644
--- a/drivers/leds/leds-tlc591xx.c
+++ b/drivers/leds/leds-tlc591xx.c
@@ -42,6 +42,9 @@
 
 #define ldev_to_led(c)		container_of(c, struct tlc591xx_led, ldev)
 
+#define TLC591XX_RESET_BYTE_0	0xa5
+#define TLC591XX_RESET_BYTE_1	0x5a
+
 struct tlc591xx_led {
 	bool active;
 	unsigned int led_no;
@@ -53,21 +56,25 @@ struct tlc591xx_priv {
 	struct tlc591xx_led leds[TLC591XX_MAX_LEDS];
 	struct regmap *regmap;
 	unsigned int reg_ledout_offset;
+	struct i2c_client *swrst_client;
 };
 
 struct tlc591xx {
 	unsigned int max_leds;
 	unsigned int reg_ledout_offset;
+	u8 swrst_addr;
 };
 
 static const struct tlc591xx tlc59116 = {
 	.max_leds = 16,
 	.reg_ledout_offset = 0x14,
+	.swrst_addr = 0x6b,
 };
 
 static const struct tlc591xx tlc59108 = {
 	.max_leds = 8,
 	.reg_ledout_offset = 0x0c,
+	.swrst_addr = 0x4b,
 };
 
 static int
@@ -140,6 +147,8 @@ tlc591xx_destroy_devices(struct tlc591xx_priv *priv, unsigned int j)
 		if (priv->leds[i].active)
 			led_classdev_unregister(&priv->leds[i].ldev);
 	}
+
+	i2c_unregister_device(priv->swrst_client);
 }
 
 static int
@@ -245,6 +254,19 @@ tlc591xx_probe(struct i2c_client *client,
 		priv->leds[reg].ldev.default_trigger =
 			of_get_property(child, "linux,default-trigger", NULL);
 	}
+
+	priv->swrst_client = i2c_new_dummy(client->adapter, tlc591xx->swrst_addr);
+	if (priv->swrst_client) {
+		err = i2c_smbus_write_byte_data(priv->swrst_client,
+				TLC591XX_RESET_BYTE_0, TLC591XX_RESET_BYTE_1);
+		if (err) {
+			dev_warn(dev, "SW reset failed\n");
+		}
+	} else {
+		dev_info(dev, "Skipping reset: address %02x already used\n",
+				tlc591xx->swrst_addr);
+	}
+
 	return tlc591xx_configure(dev, priv, tlc591xx);
 }
 
diff --git a/drivers/mtd/spi-nor/Kconfig b/drivers/mtd/spi-nor/Kconfig
index 44fe8018733c..b433e5f91069 100644
--- a/drivers/mtd/spi-nor/Kconfig
+++ b/drivers/mtd/spi-nor/Kconfig
@@ -50,15 +50,6 @@ config SPI_CADENCE_QUADSPI
 	  device with a Cadence QSPI controller and want to access the
 	  Flash as an MTD device.
 
-config SPI_FSL_QUADSPI
-	tristate "Freescale Quad SPI controller"
-	depends on ARCH_MXC || SOC_LS1021A || ARCH_LAYERSCAPE || COMPILE_TEST
-	depends on HAS_IOMEM
-	help
-	  This enables support for the Quad SPI controller in master mode.
-	  This controller does not support generic SPI. It only supports
-	  SPI NOR.
-
 config SPI_HISI_SFC
 	tristate "Hisilicon SPI-NOR Flash Controller(SFC)"
 	depends on ARCH_HISI || COMPILE_TEST
diff --git a/drivers/mtd/spi-nor/Makefile b/drivers/mtd/spi-nor/Makefile
index a552efd22958..2adedbe07662 100644
--- a/drivers/mtd/spi-nor/Makefile
+++ b/drivers/mtd/spi-nor/Makefile
@@ -2,7 +2,6 @@
 obj-$(CONFIG_MTD_SPI_NOR)	+= spi-nor.o
 obj-$(CONFIG_SPI_ASPEED_SMC)	+= aspeed-smc.o
 obj-$(CONFIG_SPI_CADENCE_QUADSPI)	+= cadence-quadspi.o
-obj-$(CONFIG_SPI_FSL_QUADSPI)	+= fsl-quadspi.o
 obj-$(CONFIG_SPI_HISI_SFC)	+= hisi-sfc.o
 obj-$(CONFIG_MTD_MT81xx_NOR)    += mtk-quadspi.o
 obj-$(CONFIG_SPI_NXP_SPIFI)	+= nxp-spifi.o
diff --git a/drivers/mtd/spi-nor/fsl-quadspi.c b/drivers/mtd/spi-nor/fsl-quadspi.c
deleted file mode 100644
index 1ff3430f82c8..000000000000
--- a/drivers/mtd/spi-nor/fsl-quadspi.c
+++ /dev/null
@@ -1,1224 +0,0 @@
-/*
- * Freescale QuadSPI driver.
- *
- * Copyright (C) 2013 Freescale Semiconductor, Inc.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- */
-#include <linux/kernel.h>
-#include <linux/module.h>
-#include <linux/interrupt.h>
-#include <linux/errno.h>
-#include <linux/platform_device.h>
-#include <linux/sched.h>
-#include <linux/delay.h>
-#include <linux/io.h>
-#include <linux/clk.h>
-#include <linux/err.h>
-#include <linux/of.h>
-#include <linux/of_device.h>
-#include <linux/timer.h>
-#include <linux/jiffies.h>
-#include <linux/completion.h>
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/partitions.h>
-#include <linux/mtd/spi-nor.h>
-#include <linux/mutex.h>
-#include <linux/pm_qos.h>
-#include <linux/sizes.h>
-
-/* Controller needs driver to swap endian */
-#define QUADSPI_QUIRK_SWAP_ENDIAN	(1 << 0)
-/* Controller needs 4x internal clock */
-#define QUADSPI_QUIRK_4X_INT_CLK	(1 << 1)
-/*
- * TKT253890, Controller needs driver to fill txfifo till 16 byte to
- * trigger data transfer even though extern data will not transferred.
- */
-#define QUADSPI_QUIRK_TKT253890		(1 << 2)
-/* Controller cannot wake up from wait mode, TKT245618 */
-#define QUADSPI_QUIRK_TKT245618         (1 << 3)
-
-/* The registers */
-#define QUADSPI_MCR			0x00
-#define QUADSPI_MCR_RESERVED_SHIFT	16
-#define QUADSPI_MCR_RESERVED_MASK	(0xF << QUADSPI_MCR_RESERVED_SHIFT)
-#define QUADSPI_MCR_MDIS_SHIFT		14
-#define QUADSPI_MCR_MDIS_MASK		(1 << QUADSPI_MCR_MDIS_SHIFT)
-#define QUADSPI_MCR_CLR_TXF_SHIFT	11
-#define QUADSPI_MCR_CLR_TXF_MASK	(1 << QUADSPI_MCR_CLR_TXF_SHIFT)
-#define QUADSPI_MCR_CLR_RXF_SHIFT	10
-#define QUADSPI_MCR_CLR_RXF_MASK	(1 << QUADSPI_MCR_CLR_RXF_SHIFT)
-#define QUADSPI_MCR_DDR_EN_SHIFT	7
-#define QUADSPI_MCR_DDR_EN_MASK		(1 << QUADSPI_MCR_DDR_EN_SHIFT)
-#define QUADSPI_MCR_END_CFG_SHIFT	2
-#define QUADSPI_MCR_END_CFG_MASK	(3 << QUADSPI_MCR_END_CFG_SHIFT)
-#define QUADSPI_MCR_SWRSTHD_SHIFT	1
-#define QUADSPI_MCR_SWRSTHD_MASK	(1 << QUADSPI_MCR_SWRSTHD_SHIFT)
-#define QUADSPI_MCR_SWRSTSD_SHIFT	0
-#define QUADSPI_MCR_SWRSTSD_MASK	(1 << QUADSPI_MCR_SWRSTSD_SHIFT)
-
-#define QUADSPI_IPCR			0x08
-#define QUADSPI_IPCR_SEQID_SHIFT	24
-#define QUADSPI_IPCR_SEQID_MASK		(0xF << QUADSPI_IPCR_SEQID_SHIFT)
-
-#define QUADSPI_BUF0CR			0x10
-#define QUADSPI_BUF1CR			0x14
-#define QUADSPI_BUF2CR			0x18
-#define QUADSPI_BUFXCR_INVALID_MSTRID	0xe
-
-#define QUADSPI_BUF3CR			0x1c
-#define QUADSPI_BUF3CR_ALLMST_SHIFT	31
-#define QUADSPI_BUF3CR_ALLMST_MASK	(1 << QUADSPI_BUF3CR_ALLMST_SHIFT)
-#define QUADSPI_BUF3CR_ADATSZ_SHIFT		8
-#define QUADSPI_BUF3CR_ADATSZ_MASK	(0xFF << QUADSPI_BUF3CR_ADATSZ_SHIFT)
-
-#define QUADSPI_BFGENCR			0x20
-#define QUADSPI_BFGENCR_PAR_EN_SHIFT	16
-#define QUADSPI_BFGENCR_PAR_EN_MASK	(1 << (QUADSPI_BFGENCR_PAR_EN_SHIFT))
-#define QUADSPI_BFGENCR_SEQID_SHIFT	12
-#define QUADSPI_BFGENCR_SEQID_MASK	(0xF << QUADSPI_BFGENCR_SEQID_SHIFT)
-
-#define QUADSPI_BUF0IND			0x30
-#define QUADSPI_BUF1IND			0x34
-#define QUADSPI_BUF2IND			0x38
-#define QUADSPI_SFAR			0x100
-
-#define QUADSPI_SMPR			0x108
-#define QUADSPI_SMPR_DDRSMP_SHIFT	16
-#define QUADSPI_SMPR_DDRSMP_MASK	(7 << QUADSPI_SMPR_DDRSMP_SHIFT)
-#define QUADSPI_SMPR_FSDLY_SHIFT	6
-#define QUADSPI_SMPR_FSDLY_MASK		(1 << QUADSPI_SMPR_FSDLY_SHIFT)
-#define QUADSPI_SMPR_FSPHS_SHIFT	5
-#define QUADSPI_SMPR_FSPHS_MASK		(1 << QUADSPI_SMPR_FSPHS_SHIFT)
-#define QUADSPI_SMPR_HSENA_SHIFT	0
-#define QUADSPI_SMPR_HSENA_MASK		(1 << QUADSPI_SMPR_HSENA_SHIFT)
-
-#define QUADSPI_RBSR			0x10c
-#define QUADSPI_RBSR_RDBFL_SHIFT	8
-#define QUADSPI_RBSR_RDBFL_MASK		(0x3F << QUADSPI_RBSR_RDBFL_SHIFT)
-
-#define QUADSPI_RBCT			0x110
-#define QUADSPI_RBCT_WMRK_MASK		0x1F
-#define QUADSPI_RBCT_RXBRD_SHIFT	8
-#define QUADSPI_RBCT_RXBRD_USEIPS	(0x1 << QUADSPI_RBCT_RXBRD_SHIFT)
-
-#define QUADSPI_TBSR			0x150
-#define QUADSPI_TBDR			0x154
-#define QUADSPI_SR			0x15c
-#define QUADSPI_SR_IP_ACC_SHIFT		1
-#define QUADSPI_SR_IP_ACC_MASK		(0x1 << QUADSPI_SR_IP_ACC_SHIFT)
-#define QUADSPI_SR_AHB_ACC_SHIFT	2
-#define QUADSPI_SR_AHB_ACC_MASK		(0x1 << QUADSPI_SR_AHB_ACC_SHIFT)
-
-#define QUADSPI_FR			0x160
-#define QUADSPI_FR_TFF_MASK		0x1
-
-#define QUADSPI_SFA1AD			0x180
-#define QUADSPI_SFA2AD			0x184
-#define QUADSPI_SFB1AD			0x188
-#define QUADSPI_SFB2AD			0x18c
-#define QUADSPI_RBDR			0x200
-
-#define QUADSPI_LUTKEY			0x300
-#define QUADSPI_LUTKEY_VALUE		0x5AF05AF0
-
-#define QUADSPI_LCKCR			0x304
-#define QUADSPI_LCKER_LOCK		0x1
-#define QUADSPI_LCKER_UNLOCK		0x2
-
-#define QUADSPI_RSER			0x164
-#define QUADSPI_RSER_TFIE		(0x1 << 0)
-
-#define QUADSPI_LUT_BASE		0x310
-
-/*
- * The definition of the LUT register shows below:
- *
- *  ---------------------------------------------------
- *  | INSTR1 | PAD1 | OPRND1 | INSTR0 | PAD0 | OPRND0 |
- *  ---------------------------------------------------
- */
-#define OPRND0_SHIFT		0
-#define PAD0_SHIFT		8
-#define INSTR0_SHIFT		10
-#define OPRND1_SHIFT		16
-
-/* Instruction set for the LUT register. */
-#define LUT_STOP		0
-#define LUT_CMD			1
-#define LUT_ADDR		2
-#define LUT_DUMMY		3
-#define LUT_MODE		4
-#define LUT_MODE2		5
-#define LUT_MODE4		6
-#define LUT_FSL_READ		7
-#define LUT_FSL_WRITE		8
-#define LUT_JMP_ON_CS		9
-#define LUT_ADDR_DDR		10
-#define LUT_MODE_DDR		11
-#define LUT_MODE2_DDR		12
-#define LUT_MODE4_DDR		13
-#define LUT_FSL_READ_DDR		14
-#define LUT_FSL_WRITE_DDR		15
-#define LUT_DATA_LEARN		16
-
-/*
- * The PAD definitions for LUT register.
- *
- * The pad stands for the lines number of IO[0:3].
- * For example, the Quad read need four IO lines, so you should
- * set LUT_PAD4 which means we use four IO lines.
- */
-#define LUT_PAD1		0
-#define LUT_PAD2		1
-#define LUT_PAD4		2
-
-/* Oprands for the LUT register. */
-#define ADDR24BIT		0x18
-#define ADDR32BIT		0x20
-
-/* Macros for constructing the LUT register. */
-#define LUT0(ins, pad, opr)						\
-		(((opr) << OPRND0_SHIFT) | ((LUT_##pad) << PAD0_SHIFT) | \
-		((LUT_##ins) << INSTR0_SHIFT))
-
-#define LUT1(ins, pad, opr)	(LUT0(ins, pad, opr) << OPRND1_SHIFT)
-
-/* other macros for LUT register. */
-#define QUADSPI_LUT(x)          (QUADSPI_LUT_BASE + (x) * 4)
-#define QUADSPI_LUT_NUM		64
-
-/* SEQID -- we can have 16 seqids at most. */
-#define SEQID_READ		0
-#define SEQID_WREN		1
-#define SEQID_WRDI		2
-#define SEQID_RDSR		3
-#define SEQID_SE		4
-#define SEQID_CHIP_ERASE	5
-#define SEQID_PP		6
-#define SEQID_RDID		7
-#define SEQID_WRSR		8
-#define SEQID_RDCR		9
-#define SEQID_EN4B		10
-#define SEQID_BRWR		11
-
-#define QUADSPI_MIN_IOMAP SZ_4M
-
-enum fsl_qspi_devtype {
-	FSL_QUADSPI_VYBRID,
-	FSL_QUADSPI_IMX6SX,
-	FSL_QUADSPI_IMX7D,
-	FSL_QUADSPI_IMX6UL,
-	FSL_QUADSPI_LS1021A,
-	FSL_QUADSPI_LS2080A,
-};
-
-struct fsl_qspi_devtype_data {
-	enum fsl_qspi_devtype devtype;
-	int rxfifo;
-	int txfifo;
-	int ahb_buf_size;
-	int driver_data;
-};
-
-static const struct fsl_qspi_devtype_data vybrid_data = {
-	.devtype = FSL_QUADSPI_VYBRID,
-	.rxfifo = 128,
-	.txfifo = 64,
-	.ahb_buf_size = 1024,
-	.driver_data = QUADSPI_QUIRK_SWAP_ENDIAN,
-};
-
-static const struct fsl_qspi_devtype_data imx6sx_data = {
-	.devtype = FSL_QUADSPI_IMX6SX,
-	.rxfifo = 128,
-	.txfifo = 512,
-	.ahb_buf_size = 1024,
-	.driver_data = QUADSPI_QUIRK_4X_INT_CLK
-		       | QUADSPI_QUIRK_TKT245618,
-};
-
-static const struct fsl_qspi_devtype_data imx7d_data = {
-	.devtype = FSL_QUADSPI_IMX7D,
-	.rxfifo = 512,
-	.txfifo = 512,
-	.ahb_buf_size = 1024,
-	.driver_data = QUADSPI_QUIRK_TKT253890
-		       | QUADSPI_QUIRK_4X_INT_CLK,
-};
-
-static const struct fsl_qspi_devtype_data imx6ul_data = {
-	.devtype = FSL_QUADSPI_IMX6UL,
-	.rxfifo = 128,
-	.txfifo = 512,
-	.ahb_buf_size = 1024,
-	.driver_data = QUADSPI_QUIRK_TKT253890
-		       | QUADSPI_QUIRK_4X_INT_CLK,
-};
-
-static struct fsl_qspi_devtype_data ls1021a_data = {
-	.devtype = FSL_QUADSPI_LS1021A,
-	.rxfifo = 128,
-	.txfifo = 64,
-	.ahb_buf_size = 1024,
-	.driver_data = 0,
-};
-
-static const struct fsl_qspi_devtype_data ls2080a_data = {
-	.devtype = FSL_QUADSPI_LS2080A,
-	.rxfifo = 128,
-	.txfifo = 64,
-	.ahb_buf_size = 1024,
-	.driver_data = QUADSPI_QUIRK_TKT253890,
-};
-
-
-#define FSL_QSPI_MAX_CHIP	4
-struct fsl_qspi {
-	struct spi_nor nor[FSL_QSPI_MAX_CHIP];
-	void __iomem *iobase;
-	void __iomem *ahb_addr;
-	u32 memmap_phy;
-	u32 memmap_offs;
-	u32 memmap_len;
-	struct clk *clk, *clk_en;
-	struct device *dev;
-	struct completion c;
-	const struct fsl_qspi_devtype_data *devtype_data;
-	u32 nor_size;
-	u32 nor_num;
-	u32 clk_rate;
-	unsigned int chip_base_addr; /* We may support two chips. */
-	bool has_second_chip;
-	bool big_endian;
-	struct mutex lock;
-	struct pm_qos_request pm_qos_req;
-};
-
-static inline int needs_swap_endian(struct fsl_qspi *q)
-{
-	return q->devtype_data->driver_data & QUADSPI_QUIRK_SWAP_ENDIAN;
-}
-
-static inline int needs_4x_clock(struct fsl_qspi *q)
-{
-	return q->devtype_data->driver_data & QUADSPI_QUIRK_4X_INT_CLK;
-}
-
-static inline int needs_fill_txfifo(struct fsl_qspi *q)
-{
-	return q->devtype_data->driver_data & QUADSPI_QUIRK_TKT253890;
-}
-
-static inline int needs_wakeup_wait_mode(struct fsl_qspi *q)
-{
-	return q->devtype_data->driver_data & QUADSPI_QUIRK_TKT245618;
-}
-
-/*
- * R/W functions for big- or little-endian registers:
- * The qSPI controller's endian is independent of the CPU core's endian.
- * So far, although the CPU core is little-endian but the qSPI have two
- * versions for big-endian and little-endian.
- */
-static void qspi_writel(struct fsl_qspi *q, u32 val, void __iomem *addr)
-{
-	if (q->big_endian)
-		iowrite32be(val, addr);
-	else
-		iowrite32(val, addr);
-}
-
-static u32 qspi_readl(struct fsl_qspi *q, void __iomem *addr)
-{
-	if (q->big_endian)
-		return ioread32be(addr);
-	else
-		return ioread32(addr);
-}
-
-/*
- * An IC bug makes us to re-arrange the 32-bit data.
- * The following chips, such as IMX6SLX, have fixed this bug.
- */
-static inline u32 fsl_qspi_endian_xchg(struct fsl_qspi *q, u32 a)
-{
-	return needs_swap_endian(q) ? __swab32(a) : a;
-}
-
-static inline void fsl_qspi_unlock_lut(struct fsl_qspi *q)
-{
-	qspi_writel(q, QUADSPI_LUTKEY_VALUE, q->iobase + QUADSPI_LUTKEY);
-	qspi_writel(q, QUADSPI_LCKER_UNLOCK, q->iobase + QUADSPI_LCKCR);
-}
-
-static inline void fsl_qspi_lock_lut(struct fsl_qspi *q)
-{
-	qspi_writel(q, QUADSPI_LUTKEY_VALUE, q->iobase + QUADSPI_LUTKEY);
-	qspi_writel(q, QUADSPI_LCKER_LOCK, q->iobase + QUADSPI_LCKCR);
-}
-
-static irqreturn_t fsl_qspi_irq_handler(int irq, void *dev_id)
-{
-	struct fsl_qspi *q = dev_id;
-	u32 reg;
-
-	/* clear interrupt */
-	reg = qspi_readl(q, q->iobase + QUADSPI_FR);
-	qspi_writel(q, reg, q->iobase + QUADSPI_FR);
-
-	if (reg & QUADSPI_FR_TFF_MASK)
-		complete(&q->c);
-
-	dev_dbg(q->dev, "QUADSPI_FR : 0x%.8x:0x%.8x\n", q->chip_base_addr, reg);
-	return IRQ_HANDLED;
-}
-
-static void fsl_qspi_init_lut(struct fsl_qspi *q)
-{
-	void __iomem *base = q->iobase;
-	int rxfifo = q->devtype_data->rxfifo;
-	u32 lut_base;
-	int i;
-
-	struct spi_nor *nor = &q->nor[0];
-	u8 addrlen = (nor->addr_width == 3) ? ADDR24BIT : ADDR32BIT;
-	u8 read_op = nor->read_opcode;
-	u8 read_dm = nor->read_dummy;
-
-	fsl_qspi_unlock_lut(q);
-
-	/* Clear all the LUT table */
-	for (i = 0; i < QUADSPI_LUT_NUM; i++)
-		qspi_writel(q, 0, base + QUADSPI_LUT_BASE + i * 4);
-
-	/* Read */
-	lut_base = SEQID_READ * 4;
-
-	qspi_writel(q, LUT0(CMD, PAD1, read_op) | LUT1(ADDR, PAD1, addrlen),
-			base + QUADSPI_LUT(lut_base));
-	qspi_writel(q, LUT0(DUMMY, PAD1, read_dm) |
-		    LUT1(FSL_READ, PAD4, rxfifo),
-			base + QUADSPI_LUT(lut_base + 1));
-
-	/* Write enable */
-	lut_base = SEQID_WREN * 4;
-	qspi_writel(q, LUT0(CMD, PAD1, SPINOR_OP_WREN),
-			base + QUADSPI_LUT(lut_base));
-
-	/* Page Program */
-	lut_base = SEQID_PP * 4;
-
-	qspi_writel(q, LUT0(CMD, PAD1, nor->program_opcode) |
-		    LUT1(ADDR, PAD1, addrlen),
-			base + QUADSPI_LUT(lut_base));
-	qspi_writel(q, LUT0(FSL_WRITE, PAD1, 0),
-			base + QUADSPI_LUT(lut_base + 1));
-
-	/* Read Status */
-	lut_base = SEQID_RDSR * 4;
-	qspi_writel(q, LUT0(CMD, PAD1, SPINOR_OP_RDSR) |
-			LUT1(FSL_READ, PAD1, 0x1),
-			base + QUADSPI_LUT(lut_base));
-
-	/* Erase a sector */
-	lut_base = SEQID_SE * 4;
-
-	qspi_writel(q, LUT0(CMD, PAD1, nor->erase_opcode) |
-		    LUT1(ADDR, PAD1, addrlen),
-			base + QUADSPI_LUT(lut_base));
-
-	/* Erase the whole chip */
-	lut_base = SEQID_CHIP_ERASE * 4;
-	qspi_writel(q, LUT0(CMD, PAD1, SPINOR_OP_CHIP_ERASE),
-			base + QUADSPI_LUT(lut_base));
-
-	/* READ ID */
-	lut_base = SEQID_RDID * 4;
-	qspi_writel(q, LUT0(CMD, PAD1, SPINOR_OP_RDID) |
-			LUT1(FSL_READ, PAD1, 0x8),
-			base + QUADSPI_LUT(lut_base));
-
-	/* Write Register */
-	lut_base = SEQID_WRSR * 4;
-	qspi_writel(q, LUT0(CMD, PAD1, SPINOR_OP_WRSR) |
-			LUT1(FSL_WRITE, PAD1, 0x2),
-			base + QUADSPI_LUT(lut_base));
-
-	/* Read Configuration Register */
-	lut_base = SEQID_RDCR * 4;
-	qspi_writel(q, LUT0(CMD, PAD1, SPINOR_OP_RDCR) |
-			LUT1(FSL_READ, PAD1, 0x1),
-			base + QUADSPI_LUT(lut_base));
-
-	/* Write disable */
-	lut_base = SEQID_WRDI * 4;
-	qspi_writel(q, LUT0(CMD, PAD1, SPINOR_OP_WRDI),
-			base + QUADSPI_LUT(lut_base));
-
-	/* Enter 4 Byte Mode (Micron) */
-	lut_base = SEQID_EN4B * 4;
-	qspi_writel(q, LUT0(CMD, PAD1, SPINOR_OP_EN4B),
-			base + QUADSPI_LUT(lut_base));
-
-	/* Enter 4 Byte Mode (Spansion) */
-	lut_base = SEQID_BRWR * 4;
-	qspi_writel(q, LUT0(CMD, PAD1, SPINOR_OP_BRWR),
-			base + QUADSPI_LUT(lut_base));
-
-	fsl_qspi_lock_lut(q);
-}
-
-/* Get the SEQID for the command */
-static int fsl_qspi_get_seqid(struct fsl_qspi *q, u8 cmd)
-{
-	switch (cmd) {
-	case SPINOR_OP_READ_1_1_4:
-	case SPINOR_OP_READ_1_1_4_4B:
-		return SEQID_READ;
-	case SPINOR_OP_WREN:
-		return SEQID_WREN;
-	case SPINOR_OP_WRDI:
-		return SEQID_WRDI;
-	case SPINOR_OP_RDSR:
-		return SEQID_RDSR;
-	case SPINOR_OP_SE:
-		return SEQID_SE;
-	case SPINOR_OP_CHIP_ERASE:
-		return SEQID_CHIP_ERASE;
-	case SPINOR_OP_PP:
-		return SEQID_PP;
-	case SPINOR_OP_RDID:
-		return SEQID_RDID;
-	case SPINOR_OP_WRSR:
-		return SEQID_WRSR;
-	case SPINOR_OP_RDCR:
-		return SEQID_RDCR;
-	case SPINOR_OP_EN4B:
-		return SEQID_EN4B;
-	case SPINOR_OP_BRWR:
-		return SEQID_BRWR;
-	default:
-		if (cmd == q->nor[0].erase_opcode)
-			return SEQID_SE;
-		dev_err(q->dev, "Unsupported cmd 0x%.2x\n", cmd);
-		break;
-	}
-	return -EINVAL;
-}
-
-static int
-fsl_qspi_runcmd(struct fsl_qspi *q, u8 cmd, unsigned int addr, int len)
-{
-	void __iomem *base = q->iobase;
-	int seqid;
-	u32 reg, reg2;
-	int err;
-
-	init_completion(&q->c);
-	dev_dbg(q->dev, "to 0x%.8x:0x%.8x, len:%d, cmd:%.2x\n",
-			q->chip_base_addr, addr, len, cmd);
-
-	/* save the reg */
-	reg = qspi_readl(q, base + QUADSPI_MCR);
-
-	qspi_writel(q, q->memmap_phy + q->chip_base_addr + addr,
-			base + QUADSPI_SFAR);
-	qspi_writel(q, QUADSPI_RBCT_WMRK_MASK | QUADSPI_RBCT_RXBRD_USEIPS,
-			base + QUADSPI_RBCT);
-	qspi_writel(q, reg | QUADSPI_MCR_CLR_RXF_MASK, base + QUADSPI_MCR);
-
-	do {
-		reg2 = qspi_readl(q, base + QUADSPI_SR);
-		if (reg2 & (QUADSPI_SR_IP_ACC_MASK | QUADSPI_SR_AHB_ACC_MASK)) {
-			udelay(1);
-			dev_dbg(q->dev, "The controller is busy, 0x%x\n", reg2);
-			continue;
-		}
-		break;
-	} while (1);
-
-	/* trigger the LUT now */
-	seqid = fsl_qspi_get_seqid(q, cmd);
-	if (seqid < 0)
-		return seqid;
-
-	qspi_writel(q, (seqid << QUADSPI_IPCR_SEQID_SHIFT) | len,
-			base + QUADSPI_IPCR);
-
-	/* Wait for the interrupt. */
-	if (!wait_for_completion_timeout(&q->c, msecs_to_jiffies(1000))) {
-		dev_err(q->dev,
-			"cmd 0x%.2x timeout, addr@%.8x, FR:0x%.8x, SR:0x%.8x\n",
-			cmd, addr, qspi_readl(q, base + QUADSPI_FR),
-			qspi_readl(q, base + QUADSPI_SR));
-		err = -ETIMEDOUT;
-	} else {
-		err = 0;
-	}
-
-	/* restore the MCR */
-	qspi_writel(q, reg, base + QUADSPI_MCR);
-
-	return err;
-}
-
-/* Read out the data from the QUADSPI_RBDR buffer registers. */
-static void fsl_qspi_read_data(struct fsl_qspi *q, int len, u8 *rxbuf)
-{
-	u32 tmp;
-	int i = 0;
-
-	while (len > 0) {
-		tmp = qspi_readl(q, q->iobase + QUADSPI_RBDR + i * 4);
-		tmp = fsl_qspi_endian_xchg(q, tmp);
-		dev_dbg(q->dev, "chip addr:0x%.8x, rcv:0x%.8x\n",
-				q->chip_base_addr, tmp);
-
-		if (len >= 4) {
-			*((u32 *)rxbuf) = tmp;
-			rxbuf += 4;
-		} else {
-			memcpy(rxbuf, &tmp, len);
-			break;
-		}
-
-		len -= 4;
-		i++;
-	}
-}
-
-/*
- * If we have changed the content of the flash by writing or erasing,
- * we need to invalidate the AHB buffer. If we do not do so, we may read out
- * the wrong data. The spec tells us reset the AHB domain and Serial Flash
- * domain at the same time.
- */
-static inline void fsl_qspi_invalid(struct fsl_qspi *q)
-{
-	u32 reg;
-
-	reg = qspi_readl(q, q->iobase + QUADSPI_MCR);
-	reg |= QUADSPI_MCR_SWRSTHD_MASK | QUADSPI_MCR_SWRSTSD_MASK;
-	qspi_writel(q, reg, q->iobase + QUADSPI_MCR);
-
-	/*
-	 * The minimum delay : 1 AHB + 2 SFCK clocks.
-	 * Delay 1 us is enough.
-	 */
-	udelay(1);
-
-	reg &= ~(QUADSPI_MCR_SWRSTHD_MASK | QUADSPI_MCR_SWRSTSD_MASK);
-	qspi_writel(q, reg, q->iobase + QUADSPI_MCR);
-}
-
-static ssize_t fsl_qspi_nor_write(struct fsl_qspi *q, struct spi_nor *nor,
-				u8 opcode, unsigned int to, u32 *txbuf,
-				unsigned count)
-{
-	int ret, i, j;
-	u32 tmp;
-
-	dev_dbg(q->dev, "to 0x%.8x:0x%.8x, len : %d\n",
-		q->chip_base_addr, to, count);
-
-	/* clear the TX FIFO. */
-	tmp = qspi_readl(q, q->iobase + QUADSPI_MCR);
-	qspi_writel(q, tmp | QUADSPI_MCR_CLR_TXF_MASK, q->iobase + QUADSPI_MCR);
-
-	/* fill the TX data to the FIFO */
-	for (j = 0, i = ((count + 3) / 4); j < i; j++) {
-		tmp = fsl_qspi_endian_xchg(q, *txbuf);
-		qspi_writel(q, tmp, q->iobase + QUADSPI_TBDR);
-		txbuf++;
-	}
-
-	/* fill the TXFIFO upto 16 bytes for i.MX7d */
-	if (needs_fill_txfifo(q))
-		for (; i < 4; i++)
-			qspi_writel(q, tmp, q->iobase + QUADSPI_TBDR);
-
-	/* Trigger it */
-	ret = fsl_qspi_runcmd(q, opcode, to, count);
-
-	if (ret == 0)
-		return count;
-
-	return ret;
-}
-
-static void fsl_qspi_set_map_addr(struct fsl_qspi *q)
-{
-	int nor_size = q->nor_size;
-	void __iomem *base = q->iobase;
-
-	qspi_writel(q, nor_size + q->memmap_phy, base + QUADSPI_SFA1AD);
-	qspi_writel(q, nor_size * 2 + q->memmap_phy, base + QUADSPI_SFA2AD);
-	qspi_writel(q, nor_size * 3 + q->memmap_phy, base + QUADSPI_SFB1AD);
-	qspi_writel(q, nor_size * 4 + q->memmap_phy, base + QUADSPI_SFB2AD);
-}
-
-/*
- * There are two different ways to read out the data from the flash:
- *  the "IP Command Read" and the "AHB Command Read".
- *
- * The IC guy suggests we use the "AHB Command Read" which is faster
- * then the "IP Command Read". (What's more is that there is a bug in
- * the "IP Command Read" in the Vybrid.)
- *
- * After we set up the registers for the "AHB Command Read", we can use
- * the memcpy to read the data directly. A "missed" access to the buffer
- * causes the controller to clear the buffer, and use the sequence pointed
- * by the QUADSPI_BFGENCR[SEQID] to initiate a read from the flash.
- */
-static int fsl_qspi_init_ahb_read(struct fsl_qspi *q)
-{
-	void __iomem *base = q->iobase;
-	int seqid;
-
-	/* AHB configuration for access buffer 0/1/2 .*/
-	qspi_writel(q, QUADSPI_BUFXCR_INVALID_MSTRID, base + QUADSPI_BUF0CR);
-	qspi_writel(q, QUADSPI_BUFXCR_INVALID_MSTRID, base + QUADSPI_BUF1CR);
-	qspi_writel(q, QUADSPI_BUFXCR_INVALID_MSTRID, base + QUADSPI_BUF2CR);
-	/*
-	 * Set ADATSZ with the maximum AHB buffer size to improve the
-	 * read performance.
-	 */
-	qspi_writel(q, QUADSPI_BUF3CR_ALLMST_MASK |
-			((q->devtype_data->ahb_buf_size / 8)
-			<< QUADSPI_BUF3CR_ADATSZ_SHIFT),
-			base + QUADSPI_BUF3CR);
-
-	/* We only use the buffer3 */
-	qspi_writel(q, 0, base + QUADSPI_BUF0IND);
-	qspi_writel(q, 0, base + QUADSPI_BUF1IND);
-	qspi_writel(q, 0, base + QUADSPI_BUF2IND);
-
-	/* Set the default lut sequence for AHB Read. */
-	seqid = fsl_qspi_get_seqid(q, q->nor[0].read_opcode);
-	if (seqid < 0)
-		return seqid;
-
-	qspi_writel(q, seqid << QUADSPI_BFGENCR_SEQID_SHIFT,
-		q->iobase + QUADSPI_BFGENCR);
-
-	return 0;
-}
-
-/* This function was used to prepare and enable QSPI clock */
-static int fsl_qspi_clk_prep_enable(struct fsl_qspi *q)
-{
-	int ret;
-
-	ret = clk_prepare_enable(q->clk_en);
-	if (ret)
-		return ret;
-
-	ret = clk_prepare_enable(q->clk);
-	if (ret) {
-		clk_disable_unprepare(q->clk_en);
-		return ret;
-	}
-
-	if (needs_wakeup_wait_mode(q))
-		pm_qos_add_request(&q->pm_qos_req, PM_QOS_CPU_DMA_LATENCY, 0);
-
-	return 0;
-}
-
-/* This function was used to disable and unprepare QSPI clock */
-static void fsl_qspi_clk_disable_unprep(struct fsl_qspi *q)
-{
-	if (needs_wakeup_wait_mode(q))
-		pm_qos_remove_request(&q->pm_qos_req);
-
-	clk_disable_unprepare(q->clk);
-	clk_disable_unprepare(q->clk_en);
-
-}
-
-/* We use this function to do some basic init for spi_nor_scan(). */
-static int fsl_qspi_nor_setup(struct fsl_qspi *q)
-{
-	void __iomem *base = q->iobase;
-	u32 reg;
-	int ret;
-
-	/* disable and unprepare clock to avoid glitch pass to controller */
-	fsl_qspi_clk_disable_unprep(q);
-
-	/* the default frequency, we will change it in the future. */
-	ret = clk_set_rate(q->clk, 66000000);
-	if (ret)
-		return ret;
-
-	ret = fsl_qspi_clk_prep_enable(q);
-	if (ret)
-		return ret;
-
-	/* Reset the module */
-	qspi_writel(q, QUADSPI_MCR_SWRSTSD_MASK | QUADSPI_MCR_SWRSTHD_MASK,
-		base + QUADSPI_MCR);
-	udelay(1);
-
-	/* Init the LUT table. */
-	fsl_qspi_init_lut(q);
-
-	/* Disable the module */
-	qspi_writel(q, QUADSPI_MCR_MDIS_MASK | QUADSPI_MCR_RESERVED_MASK,
-			base + QUADSPI_MCR);
-
-	reg = qspi_readl(q, base + QUADSPI_SMPR);
-	qspi_writel(q, reg & ~(QUADSPI_SMPR_FSDLY_MASK
-			| QUADSPI_SMPR_FSPHS_MASK
-			| QUADSPI_SMPR_HSENA_MASK
-			| QUADSPI_SMPR_DDRSMP_MASK), base + QUADSPI_SMPR);
-
-	/* Enable the module */
-	qspi_writel(q, QUADSPI_MCR_RESERVED_MASK | QUADSPI_MCR_END_CFG_MASK,
-			base + QUADSPI_MCR);
-
-	/* clear all interrupt status */
-	qspi_writel(q, 0xffffffff, q->iobase + QUADSPI_FR);
-
-	/* enable the interrupt */
-	qspi_writel(q, QUADSPI_RSER_TFIE, q->iobase + QUADSPI_RSER);
-
-	return 0;
-}
-
-static int fsl_qspi_nor_setup_last(struct fsl_qspi *q)
-{
-	unsigned long rate = q->clk_rate;
-	int ret;
-
-	if (needs_4x_clock(q))
-		rate *= 4;
-
-	/* disable and unprepare clock to avoid glitch pass to controller */
-	fsl_qspi_clk_disable_unprep(q);
-
-	ret = clk_set_rate(q->clk, rate);
-	if (ret)
-		return ret;
-
-	ret = fsl_qspi_clk_prep_enable(q);
-	if (ret)
-		return ret;
-
-	/* Init the LUT table again. */
-	fsl_qspi_init_lut(q);
-
-	/* Init for AHB read */
-	return fsl_qspi_init_ahb_read(q);
-}
-
-static const struct of_device_id fsl_qspi_dt_ids[] = {
-	{ .compatible = "fsl,vf610-qspi", .data = &vybrid_data, },
-	{ .compatible = "fsl,imx6sx-qspi", .data = &imx6sx_data, },
-	{ .compatible = "fsl,imx7d-qspi", .data = &imx7d_data, },
-	{ .compatible = "fsl,imx6ul-qspi", .data = &imx6ul_data, },
-	{ .compatible = "fsl,ls1021a-qspi", .data = (void *)&ls1021a_data, },
-	{ .compatible = "fsl,ls2080a-qspi", .data = &ls2080a_data, },
-	{ /* sentinel */ }
-};
-MODULE_DEVICE_TABLE(of, fsl_qspi_dt_ids);
-
-static void fsl_qspi_set_base_addr(struct fsl_qspi *q, struct spi_nor *nor)
-{
-	q->chip_base_addr = q->nor_size * (nor - q->nor);
-}
-
-static int fsl_qspi_read_reg(struct spi_nor *nor, u8 opcode, u8 *buf, int len)
-{
-	int ret;
-	struct fsl_qspi *q = nor->priv;
-
-	ret = fsl_qspi_runcmd(q, opcode, 0, len);
-	if (ret)
-		return ret;
-
-	fsl_qspi_read_data(q, len, buf);
-	return 0;
-}
-
-static int fsl_qspi_write_reg(struct spi_nor *nor, u8 opcode, u8 *buf, int len)
-{
-	struct fsl_qspi *q = nor->priv;
-	int ret;
-
-	if (!buf) {
-		ret = fsl_qspi_runcmd(q, opcode, 0, 1);
-		if (ret)
-			return ret;
-
-		if (opcode == SPINOR_OP_CHIP_ERASE)
-			fsl_qspi_invalid(q);
-
-	} else if (len > 0) {
-		ret = fsl_qspi_nor_write(q, nor, opcode, 0,
-					(u32 *)buf, len);
-		if (ret > 0)
-			return 0;
-	} else {
-		dev_err(q->dev, "invalid cmd %d\n", opcode);
-		ret = -EINVAL;
-	}
-
-	return ret;
-}
-
-static ssize_t fsl_qspi_write(struct spi_nor *nor, loff_t to,
-			      size_t len, const u_char *buf)
-{
-	struct fsl_qspi *q = nor->priv;
-	ssize_t ret = fsl_qspi_nor_write(q, nor, nor->program_opcode, to,
-					 (u32 *)buf, len);
-
-	/* invalid the data in the AHB buffer. */
-	fsl_qspi_invalid(q);
-	return ret;
-}
-
-static ssize_t fsl_qspi_read(struct spi_nor *nor, loff_t from,
-			     size_t len, u_char *buf)
-{
-	struct fsl_qspi *q = nor->priv;
-	u8 cmd = nor->read_opcode;
-
-	/* if necessary,ioremap buffer before AHB read, */
-	if (!q->ahb_addr) {
-		q->memmap_offs = q->chip_base_addr + from;
-		q->memmap_len = len > QUADSPI_MIN_IOMAP ? len : QUADSPI_MIN_IOMAP;
-
-		q->ahb_addr = ioremap_nocache(
-				q->memmap_phy + q->memmap_offs,
-				q->memmap_len);
-		if (!q->ahb_addr) {
-			dev_err(q->dev, "ioremap failed\n");
-			return -ENOMEM;
-		}
-	/* ioremap if the data requested is out of range */
-	} else if (q->chip_base_addr + from < q->memmap_offs
-			|| q->chip_base_addr + from + len >
-			q->memmap_offs + q->memmap_len) {
-		iounmap(q->ahb_addr);
-
-		q->memmap_offs = q->chip_base_addr + from;
-		q->memmap_len = len > QUADSPI_MIN_IOMAP ? len : QUADSPI_MIN_IOMAP;
-		q->ahb_addr = ioremap_nocache(
-				q->memmap_phy + q->memmap_offs,
-				q->memmap_len);
-		if (!q->ahb_addr) {
-			dev_err(q->dev, "ioremap failed\n");
-			return -ENOMEM;
-		}
-	}
-
-	dev_dbg(q->dev, "cmd [%x],read from %p, len:%zd\n",
-		cmd, q->ahb_addr + q->chip_base_addr + from - q->memmap_offs,
-		len);
-
-	/* Read out the data directly from the AHB buffer.*/
-	memcpy(buf, q->ahb_addr + q->chip_base_addr + from - q->memmap_offs,
-		len);
-
-	return len;
-}
-
-static int fsl_qspi_erase(struct spi_nor *nor, loff_t offs)
-{
-	struct fsl_qspi *q = nor->priv;
-	int ret;
-
-	dev_dbg(nor->dev, "%dKiB at 0x%08x:0x%08x\n",
-		nor->mtd.erasesize / 1024, q->chip_base_addr, (u32)offs);
-
-	ret = fsl_qspi_runcmd(q, nor->erase_opcode, offs, 0);
-	if (ret)
-		return ret;
-
-	fsl_qspi_invalid(q);
-	return 0;
-}
-
-static int fsl_qspi_prep(struct spi_nor *nor, enum spi_nor_ops ops)
-{
-	struct fsl_qspi *q = nor->priv;
-	int ret;
-
-	mutex_lock(&q->lock);
-
-	ret = fsl_qspi_clk_prep_enable(q);
-	if (ret)
-		goto err_mutex;
-
-	fsl_qspi_set_base_addr(q, nor);
-	return 0;
-
-err_mutex:
-	mutex_unlock(&q->lock);
-	return ret;
-}
-
-static void fsl_qspi_unprep(struct spi_nor *nor, enum spi_nor_ops ops)
-{
-	struct fsl_qspi *q = nor->priv;
-
-	fsl_qspi_clk_disable_unprep(q);
-	mutex_unlock(&q->lock);
-}
-
-static int fsl_qspi_probe(struct platform_device *pdev)
-{
-	const struct spi_nor_hwcaps hwcaps = {
-		.mask = SNOR_HWCAPS_READ_1_1_4 |
-			SNOR_HWCAPS_PP,
-	};
-	struct device_node *np = pdev->dev.of_node;
-	struct device *dev = &pdev->dev;
-	struct fsl_qspi *q;
-	struct resource *res;
-	struct spi_nor *nor;
-	struct mtd_info *mtd;
-	int ret, i = 0;
-
-	q = devm_kzalloc(dev, sizeof(*q), GFP_KERNEL);
-	if (!q)
-		return -ENOMEM;
-
-	q->nor_num = of_get_child_count(dev->of_node);
-	if (!q->nor_num || q->nor_num > FSL_QSPI_MAX_CHIP)
-		return -ENODEV;
-
-	q->dev = dev;
-	q->devtype_data = of_device_get_match_data(dev);
-	if (!q->devtype_data)
-		return -ENODEV;
-	platform_set_drvdata(pdev, q);
-
-	/* find the resources */
-	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "QuadSPI");
-	q->iobase = devm_ioremap_resource(dev, res);
-	if (IS_ERR(q->iobase))
-		return PTR_ERR(q->iobase);
-
-	q->big_endian = of_property_read_bool(np, "big-endian");
-	res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
-					"QuadSPI-memory");
-	if (!devm_request_mem_region(dev, res->start, resource_size(res),
-				     res->name)) {
-		dev_err(dev, "can't request region for resource %pR\n", res);
-		return -EBUSY;
-	}
-
-	q->memmap_phy = res->start;
-
-	/* find the clocks */
-	q->clk_en = devm_clk_get(dev, "qspi_en");
-	if (IS_ERR(q->clk_en))
-		return PTR_ERR(q->clk_en);
-
-	q->clk = devm_clk_get(dev, "qspi");
-	if (IS_ERR(q->clk))
-		return PTR_ERR(q->clk);
-
-	ret = fsl_qspi_clk_prep_enable(q);
-	if (ret) {
-		dev_err(dev, "can not enable the clock\n");
-		goto clk_failed;
-	}
-
-	/* find the irq */
-	ret = platform_get_irq(pdev, 0);
-	if (ret < 0) {
-		dev_err(dev, "failed to get the irq: %d\n", ret);
-		goto irq_failed;
-	}
-
-	ret = devm_request_irq(dev, ret,
-			fsl_qspi_irq_handler, 0, pdev->name, q);
-	if (ret) {
-		dev_err(dev, "failed to request irq: %d\n", ret);
-		goto irq_failed;
-	}
-
-	ret = fsl_qspi_nor_setup(q);
-	if (ret)
-		goto irq_failed;
-
-	if (of_get_property(np, "fsl,qspi-has-second-chip", NULL))
-		q->has_second_chip = true;
-
-	mutex_init(&q->lock);
-
-	/* iterate the subnodes. */
-	for_each_available_child_of_node(dev->of_node, np) {
-		/* skip the holes */
-		if (!q->has_second_chip)
-			i *= 2;
-
-		nor = &q->nor[i];
-		mtd = &nor->mtd;
-
-		nor->dev = dev;
-		spi_nor_set_flash_node(nor, np);
-		nor->priv = q;
-
-		if (q->nor_num > 1 && !mtd->name) {
-			int spiflash_idx;
-
-			ret = of_property_read_u32(np, "reg", &spiflash_idx);
-			if (!ret) {
-				mtd->name = devm_kasprintf(dev, GFP_KERNEL,
-							   "%s-%d",
-							   dev_name(dev),
-							   spiflash_idx);
-				if (!mtd->name) {
-					ret = -ENOMEM;
-					goto mutex_failed;
-				}
-			} else {
-				dev_warn(dev, "reg property is missing\n");
-			}
-		}
-
-		/* fill the hooks */
-		nor->read_reg = fsl_qspi_read_reg;
-		nor->write_reg = fsl_qspi_write_reg;
-		nor->read = fsl_qspi_read;
-		nor->write = fsl_qspi_write;
-		nor->erase = fsl_qspi_erase;
-
-		nor->prepare = fsl_qspi_prep;
-		nor->unprepare = fsl_qspi_unprep;
-
-		ret = of_property_read_u32(np, "spi-max-frequency",
-				&q->clk_rate);
-		if (ret < 0)
-			goto mutex_failed;
-
-		/* set the chip address for READID */
-		fsl_qspi_set_base_addr(q, nor);
-
-		ret = spi_nor_scan(nor, NULL, &hwcaps);
-		if (ret)
-			goto mutex_failed;
-
-		ret = mtd_device_register(mtd, NULL, 0);
-		if (ret)
-			goto mutex_failed;
-
-		/* Set the correct NOR size now. */
-		if (q->nor_size == 0) {
-			q->nor_size = mtd->size;
-
-			/* Map the SPI NOR to accessiable address */
-			fsl_qspi_set_map_addr(q);
-		}
-
-		/*
-		 * The TX FIFO is 64 bytes in the Vybrid, but the Page Program
-		 * may writes 265 bytes per time. The write is working in the
-		 * unit of the TX FIFO, not in the unit of the SPI NOR's page
-		 * size.
-		 *
-		 * So shrink the spi_nor->page_size if it is larger then the
-		 * TX FIFO.
-		 */
-		if (nor->page_size > q->devtype_data->txfifo)
-			nor->page_size = q->devtype_data->txfifo;
-
-		i++;
-	}
-
-	/* finish the rest init. */
-	ret = fsl_qspi_nor_setup_last(q);
-	if (ret)
-		goto last_init_failed;
-
-	fsl_qspi_clk_disable_unprep(q);
-	return 0;
-
-last_init_failed:
-	for (i = 0; i < q->nor_num; i++) {
-		/* skip the holes */
-		if (!q->has_second_chip)
-			i *= 2;
-		mtd_device_unregister(&q->nor[i].mtd);
-	}
-mutex_failed:
-	mutex_destroy(&q->lock);
-irq_failed:
-	fsl_qspi_clk_disable_unprep(q);
-clk_failed:
-	dev_err(dev, "Freescale QuadSPI probe failed\n");
-	return ret;
-}
-
-static int fsl_qspi_remove(struct platform_device *pdev)
-{
-	struct fsl_qspi *q = platform_get_drvdata(pdev);
-	int i;
-
-	for (i = 0; i < q->nor_num; i++) {
-		/* skip the holes */
-		if (!q->has_second_chip)
-			i *= 2;
-		mtd_device_unregister(&q->nor[i].mtd);
-	}
-
-	/* disable the hardware */
-	qspi_writel(q, QUADSPI_MCR_MDIS_MASK, q->iobase + QUADSPI_MCR);
-	qspi_writel(q, 0x0, q->iobase + QUADSPI_RSER);
-
-	mutex_destroy(&q->lock);
-
-	if (q->ahb_addr)
-		iounmap(q->ahb_addr);
-
-	return 0;
-}
-
-static int fsl_qspi_suspend(struct platform_device *pdev, pm_message_t state)
-{
-	return 0;
-}
-
-static int fsl_qspi_resume(struct platform_device *pdev)
-{
-	int ret;
-	struct fsl_qspi *q = platform_get_drvdata(pdev);
-
-	ret = fsl_qspi_clk_prep_enable(q);
-	if (ret)
-		return ret;
-
-	fsl_qspi_nor_setup(q);
-	fsl_qspi_set_map_addr(q);
-	fsl_qspi_nor_setup_last(q);
-
-	fsl_qspi_clk_disable_unprep(q);
-
-	return 0;
-}
-
-static struct platform_driver fsl_qspi_driver = {
-	.driver = {
-		.name	= "fsl-quadspi",
-		.of_match_table = fsl_qspi_dt_ids,
-	},
-	.probe          = fsl_qspi_probe,
-	.remove		= fsl_qspi_remove,
-	.suspend	= fsl_qspi_suspend,
-	.resume		= fsl_qspi_resume,
-};
-module_platform_driver(fsl_qspi_driver);
-
-MODULE_DESCRIPTION("Freescale QuadSPI Controller Driver");
-MODULE_AUTHOR("Freescale Semiconductor Inc.");
-MODULE_LICENSE("GPL v2");
diff --git a/drivers/pinctrl/pinctrl-mcp23s08.c b/drivers/pinctrl/pinctrl-mcp23s08.c
index 98905d4a79ca..dac31601fc53 100644
--- a/drivers/pinctrl/pinctrl-mcp23s08.c
+++ b/drivers/pinctrl/pinctrl-mcp23s08.c
@@ -68,6 +68,7 @@ struct mcp23s08 {
 	struct mutex		lock;
 
 	struct gpio_chip	chip;
+	struct irq_chip		irq_chip;
 
 	struct regmap		*regmap;
 	struct device		*dev;
@@ -265,7 +266,6 @@ static int mcp_pinconf_get(struct pinctrl_dev *pctldev, unsigned int pin,
 		status = (data & BIT(pin)) ? 1 : 0;
 		break;
 	default:
-		dev_err(mcp->dev, "Invalid config param %04x\n", param);
 		return -ENOTSUPP;
 	}
 
@@ -292,7 +292,7 @@ static int mcp_pinconf_set(struct pinctrl_dev *pctldev, unsigned int pin,
 			ret = mcp_set_bit(mcp, MCP_GPPU, pin, arg);
 			break;
 		default:
-			dev_err(mcp->dev, "Invalid config param %04x\n", param);
+			dev_dbg(mcp->dev, "Invalid config param %04x\n", param);
 			return -ENOTSUPP;
 		}
 	}
@@ -607,15 +607,6 @@ static void mcp23s08_irq_bus_unlock(struct irq_data *data)
 	mutex_unlock(&mcp->lock);
 }
 
-static struct irq_chip mcp23s08_irq_chip = {
-	.name = "gpio-mcp23xxx",
-	.irq_mask = mcp23s08_irq_mask,
-	.irq_unmask = mcp23s08_irq_unmask,
-	.irq_set_type = mcp23s08_irq_set_type,
-	.irq_bus_lock = mcp23s08_irq_bus_lock,
-	.irq_bus_sync_unlock = mcp23s08_irq_bus_unlock,
-};
-
 static int mcp23s08_irq_setup(struct mcp23s08 *mcp)
 {
 	struct gpio_chip *chip = &mcp->chip;
@@ -645,7 +636,7 @@ static int mcp23s08_irqchip_setup(struct mcp23s08 *mcp)
 	int err;
 
 	err =  gpiochip_irqchip_add_nested(chip,
-					   &mcp23s08_irq_chip,
+					   &mcp->irq_chip,
 					   0,
 					   handle_simple_irq,
 					   IRQ_TYPE_NONE);
@@ -656,7 +647,7 @@ static int mcp23s08_irqchip_setup(struct mcp23s08 *mcp)
 	}
 
 	gpiochip_set_nested_irqchip(chip,
-				    &mcp23s08_irq_chip,
+				    &mcp->irq_chip,
 				    mcp->irq);
 
 	return 0;
@@ -664,115 +655,6 @@ static int mcp23s08_irqchip_setup(struct mcp23s08 *mcp)
 
 /*----------------------------------------------------------------------*/
 
-#ifdef CONFIG_DEBUG_FS
-
-#include <linux/seq_file.h>
-
-/*
- * This compares the chip's registers with the register
- * cache and corrects any incorrectly set register. This
- * can be used to fix state for MCP23xxx, that temporary
- * lost its power supply.
- */
-#define MCP23S08_CONFIG_REGS 7
-static int __check_mcp23s08_reg_cache(struct mcp23s08 *mcp)
-{
-	int cached[MCP23S08_CONFIG_REGS];
-	int err = 0, i;
-
-	/* read cached config registers */
-	for (i = 0; i < MCP23S08_CONFIG_REGS; i++) {
-		err = mcp_read(mcp, i, &cached[i]);
-		if (err)
-			goto out;
-	}
-
-	regcache_cache_bypass(mcp->regmap, true);
-
-	for (i = 0; i < MCP23S08_CONFIG_REGS; i++) {
-		int uncached;
-		err = mcp_read(mcp, i, &uncached);
-		if (err)
-			goto out;
-
-		if (uncached != cached[i]) {
-			dev_err(mcp->dev, "restoring reg 0x%02x from 0x%04x to 0x%04x (power-loss?)\n",
-				i, uncached, cached[i]);
-			mcp_write(mcp, i, cached[i]);
-		}
-	}
-
-out:
-	if (err)
-		dev_err(mcp->dev, "read error: reg=%02x, err=%d", i, err);
-	regcache_cache_bypass(mcp->regmap, false);
-	return err;
-}
-
-/*
- * This shows more info than the generic gpio dump code:
- * pullups, deglitching, open drain drive.
- */
-static void mcp23s08_dbg_show(struct seq_file *s, struct gpio_chip *chip)
-{
-	struct mcp23s08	*mcp;
-	char		bank;
-	int		t;
-	unsigned	mask;
-	int iodir, gpio, gppu;
-
-	mcp = gpiochip_get_data(chip);
-
-	/* NOTE: we only handle one bank for now ... */
-	bank = '0' + ((mcp->addr >> 1) & 0x7);
-
-	mutex_lock(&mcp->lock);
-
-	t = __check_mcp23s08_reg_cache(mcp);
-	if (t) {
-		seq_printf(s, " I/O Error\n");
-		goto done;
-	}
-	t = mcp_read(mcp, MCP_IODIR, &iodir);
-	if (t) {
-		seq_printf(s, " I/O Error\n");
-		goto done;
-	}
-	t = mcp_read(mcp, MCP_GPIO, &gpio);
-	if (t) {
-		seq_printf(s, " I/O Error\n");
-		goto done;
-	}
-	t = mcp_read(mcp, MCP_GPPU, &gppu);
-	if (t) {
-		seq_printf(s, " I/O Error\n");
-		goto done;
-	}
-
-	for (t = 0, mask = BIT(0); t < chip->ngpio; t++, mask <<= 1) {
-		const char *label;
-
-		label = gpiochip_is_requested(chip, t);
-		if (!label)
-			continue;
-
-		seq_printf(s, " gpio-%-3d P%c.%d (%-12s) %s %s %s\n",
-			   chip->base + t, bank, t, label,
-			   (iodir & mask) ? "in " : "out",
-			   (gpio & mask) ? "hi" : "lo",
-			   (gppu & mask) ? "up" : "  ");
-		/* NOTE:  ignoring the irq-related registers */
-	}
-done:
-	mutex_unlock(&mcp->lock);
-}
-
-#else
-#define mcp23s08_dbg_show	NULL
-#endif
-
-/*----------------------------------------------------------------------*/
-
 static int mcp23s08_probe_one(struct mcp23s08 *mcp, struct device *dev,
 			      void *data, unsigned addr, unsigned type,
 			      unsigned int base, int cs)
@@ -793,7 +675,6 @@ static int mcp23s08_probe_one(struct mcp23s08 *mcp, struct device *dev,
 	mcp->chip.get = mcp23s08_get;
 	mcp->chip.direction_output = mcp23s08_direction_output;
 	mcp->chip.set = mcp23s08_set;
-	mcp->chip.dbg_show = mcp23s08_dbg_show;
 #ifdef CONFIG_OF_GPIO
 	mcp->chip.of_gpio_n_cells = 2;
 	mcp->chip.of_node = dev->of_node;
@@ -1047,6 +928,13 @@ static int mcp230xx_probe(struct i2c_client *client,
 		return -ENOMEM;
 
 	mcp->irq = client->irq;
+	mcp->irq_chip.name = dev_name(&client->dev);
+	mcp->irq_chip.irq_mask = mcp23s08_irq_mask;
+	mcp->irq_chip.irq_unmask = mcp23s08_irq_unmask;
+	mcp->irq_chip.irq_set_type = mcp23s08_irq_set_type;
+	mcp->irq_chip.irq_bus_lock = mcp23s08_irq_bus_lock;
+	mcp->irq_chip.irq_bus_sync_unlock = mcp23s08_irq_bus_unlock;
+
 	status = mcp23s08_probe_one(mcp, &client->dev, client, client->addr,
 				    id->driver_data, pdata->base, 0);
 	if (status)
@@ -1104,6 +992,7 @@ static int mcp23s08_probe(struct spi_device *spi)
 	int				status, type;
 	unsigned			ngpio = 0;
 	const struct			of_device_id *match;
+	struct device_node		*np;
 
 	match = of_match_device(of_match_ptr(mcp23s08_spi_of_match), &spi->dev);
 	if (match)
@@ -1144,8 +1033,7 @@ static int mcp23s08_probe(struct spi_device *spi)
 		return -ENODEV;
 
 	data = devm_kzalloc(&spi->dev,
-			    sizeof(*data) + chips * sizeof(struct mcp23s08),
-			    GFP_KERNEL);
+			    struct_size(data, chip, chips), GFP_KERNEL);
 	if (!data)
 		return -ENOMEM;
 
@@ -1157,6 +1045,13 @@ static int mcp23s08_probe(struct spi_device *spi)
 		chips--;
 		data->mcp[addr] = &data->chip[chips];
 		data->mcp[addr]->irq = spi->irq;
+		data->mcp[addr]->irq_chip.name = dev_name(&spi->dev);
+		data->mcp[addr]->irq_chip.irq_mask = mcp23s08_irq_mask;
+		data->mcp[addr]->irq_chip.irq_unmask = mcp23s08_irq_unmask;
+		data->mcp[addr]->irq_chip.irq_set_type = mcp23s08_irq_set_type;
+		data->mcp[addr]->irq_chip.irq_bus_lock = mcp23s08_irq_bus_lock;
+		data->mcp[addr]->irq_chip.irq_bus_sync_unlock =
+			mcp23s08_irq_bus_unlock;
 		status = mcp23s08_probe_one(data->mcp[addr], &spi->dev, spi,
 					    0x40 | (addr << 1), type,
 					    pdata->base, addr);
@@ -1166,6 +1061,16 @@ static int mcp23s08_probe(struct spi_device *spi)
 		if (pdata->base != -1)
 			pdata->base += data->mcp[addr]->chip.ngpio;
 		ngpio += data->mcp[addr]->chip.ngpio;
+
+		for_each_available_child_of_node(spi->dev.of_node, np) {
+			u32 chip_addr;
+			status = of_property_read_u32(np, "address", &chip_addr);
+			if (status)
+				continue;
+			if (chip_addr != addr)
+				continue;
+			devprop_gpiochip_set_names(&data->mcp[addr]->chip, of_fwnode_handle(np));
+		}
 	}
 	data->ngpio = ngpio;
 
diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
index 9f89cb134549..f761655e2a36 100644
--- a/drivers/spi/Kconfig
+++ b/drivers/spi/Kconfig
@@ -63,7 +63,7 @@ config SPI_ALTERA
 
 config SPI_ATH79
 	tristate "Atheros AR71XX/AR724X/AR913X SPI controller driver"
-	depends on ATH79 && GPIOLIB
+	depends on ATH79 || COMPILE_TEST
 	select SPI_BITBANG
 	help
 	  This enables support for the SPI controller present on the
@@ -268,6 +268,27 @@ config SPI_FSL_LPSPI
 	help
 	  This enables Freescale i.MX LPSPI controllers in master mode.
 
+config SPI_FSL_QUADSPI
+	tristate "Freescale QSPI controller"
+	depends on ARCH_MXC || SOC_LS1021A || ARCH_LAYERSCAPE || COMPILE_TEST
+	depends on HAS_IOMEM
+	help
+	  This enables support for the Quad SPI controller in master mode.
+	  Up to four flash chips can be connected on two buses with two
+	  chipselects each.
+	  This controller does not support generic SPI messages. It only
+	  supports the high-level SPI memory interface.
+
+config SPI_NXP_FLEXSPI
+	tristate "NXP Flex SPI controller"
+	depends on ARCH_LAYERSCAPE || HAS_IOMEM
+	help
+	  This enables support for the Flex SPI controller in master mode.
+	  Up to four slave devices can be connected on two buses with two
+	  chipselects each.
+	  This controller does not support generic SPI messages and only
+	  supports the high-level SPI memory interface.
+
 config SPI_GPIO
 	tristate "GPIO-based bitbanging SPI Master"
 	depends on GPIOLIB || COMPILE_TEST
@@ -296,8 +317,7 @@ config SPI_IMX
 	depends on ARCH_MXC || COMPILE_TEST
 	select SPI_BITBANG
 	help
-	  This enables using the Freescale i.MX SPI controllers in master
-	  mode.
+	  This enables support for the Freescale i.MX SPI controllers.
 
 config SPI_JCORE
 	tristate "J-Core SPI Master"
@@ -372,7 +392,7 @@ config SPI_FSL_DSPI
 	depends on SOC_VF610 || SOC_LS1021A || ARCH_LAYERSCAPE || M5441x || COMPILE_TEST
 	help
 	  This enables support for the Freescale DSPI controller in master
-	  mode. VF610 platform uses the controller.
+	  mode. VF610, LS1021A and ColdFire platforms uses the controller.
 
 config SPI_FSL_ESPI
 	tristate "Freescale eSPI controller"
@@ -631,6 +651,12 @@ config SPI_SH_HSPI
 	help
 	  SPI driver for SuperH HSPI blocks.
 
+config SPI_SIFIVE
+	tristate "SiFive SPI controller"
+	depends on HAS_IOMEM
+	help
+	  This exposes the SPI controller IP from SiFive.
+
 config SPI_SIRF
 	tristate "CSR SiRFprimaII SPI controller"
 	depends on SIRF_DMA
@@ -665,7 +691,7 @@ config SPI_STM32
 	tristate "STMicroelectronics STM32 SPI controller"
 	depends on ARCH_STM32 || COMPILE_TEST
 	help
-	  SPI driver for STMicroelectonics STM32 SoCs.
+	  SPI driver for STMicroelectronics STM32 SoCs.
 
 	  STM32 SPI controller supports DMA and PIO modes. When DMA
 	  is not available, the driver automatically falls back to
diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile
index f29627040dfb..d8fc03c9faa2 100644
--- a/drivers/spi/Makefile
+++ b/drivers/spi/Makefile
@@ -45,6 +45,7 @@ obj-$(CONFIG_SPI_FSL_DSPI)		+= spi-fsl-dspi.o
 obj-$(CONFIG_SPI_FSL_LIB)		+= spi-fsl-lib.o
 obj-$(CONFIG_SPI_FSL_ESPI)		+= spi-fsl-espi.o
 obj-$(CONFIG_SPI_FSL_LPSPI)		+= spi-fsl-lpspi.o
+obj-$(CONFIG_SPI_FSL_QUADSPI)		+= spi-fsl-qspi.o
 obj-$(CONFIG_SPI_FSL_SPI)		+= spi-fsl-spi.o
 obj-$(CONFIG_SPI_GPIO)			+= spi-gpio.o
 obj-$(CONFIG_SPI_IMG_SPFI)		+= spi-img-spfi.o
@@ -63,6 +64,7 @@ obj-$(CONFIG_SPI_MXIC)			+= spi-mxic.o
 obj-$(CONFIG_SPI_MXS)			+= spi-mxs.o
 obj-$(CONFIG_SPI_NPCM_PSPI)		+= spi-npcm-pspi.o
 obj-$(CONFIG_SPI_NUC900)		+= spi-nuc900.o
+obj-$(CONFIG_SPI_NXP_FLEXSPI)		+= spi-nxp-fspi.o
 obj-$(CONFIG_SPI_OC_TINY)		+= spi-oc-tiny.o
 spi-octeon-objs				:= spi-cavium.o spi-cavium-octeon.o
 obj-$(CONFIG_SPI_OCTEON)		+= spi-octeon.o
@@ -93,6 +95,7 @@ obj-$(CONFIG_SPI_SH)			+= spi-sh.o
 obj-$(CONFIG_SPI_SH_HSPI)		+= spi-sh-hspi.o
 obj-$(CONFIG_SPI_SH_MSIOF)		+= spi-sh-msiof.o
 obj-$(CONFIG_SPI_SH_SCI)		+= spi-sh-sci.o
+obj-$(CONFIG_SPI_SIFIVE)		+= spi-sifive.o
 obj-$(CONFIG_SPI_SIRF)		+= spi-sirf.o
 obj-$(CONFIG_SPI_SLAVE_MT27XX)          += spi-slave-mt27xx.o
 obj-$(CONFIG_SPI_SPRD)			+= spi-sprd.o
diff --git a/drivers/spi/atmel-quadspi.c b/drivers/spi/atmel-quadspi.c
index ddc712410812..fffc21cd5f79 100644
--- a/drivers/spi/atmel-quadspi.c
+++ b/drivers/spi/atmel-quadspi.c
@@ -1,3 +1,4 @@
+// SPDX-License-Identifier: GPL-2.0
 /*
  * Driver for Atmel QSPI Controller
  *
@@ -7,31 +8,19 @@
  * Author: Cyrille Pitchen <cyrille.pitchen@atmel.com>
  * Author: Piotr Bugalski <bugalski.piotr@gmail.com>
  *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- * This program is distributed in the hope that it will be useful, but WITHOUT
- * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
- * more details.
- *
- * You should have received a copy of the GNU General Public License along with
- * this program.  If not, see <http://www.gnu.org/licenses/>.
- *
  * This driver is based on drivers/mtd/spi-nor/fsl-quadspi.c from Freescale.
  */
 
-#include <linux/kernel.h>
 #include <linux/clk.h>
-#include <linux/module.h>
-#include <linux/platform_device.h>
 #include <linux/delay.h>
 #include <linux/err.h>
 #include <linux/interrupt.h>
-#include <linux/of.h>
-
 #include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_platform.h>
+#include <linux/platform_device.h>
 #include <linux/spi/spi-mem.h>
 
 /* QSPI register offsets */
@@ -47,7 +36,9 @@
 
 #define QSPI_IAR     0x0030  /* Instruction Address Register */
 #define QSPI_ICR     0x0034  /* Instruction Code Register */
+#define QSPI_WICR    0x0034  /* Write Instruction Code Register */
 #define QSPI_IFR     0x0038  /* Instruction Frame Register */
+#define QSPI_RICR    0x003C  /* Read Instruction Code Register */
 
 #define QSPI_SMR     0x0040  /* Scrambling Mode Register */
 #define QSPI_SKR     0x0044  /* Scrambling Key Register */
@@ -100,7 +91,7 @@
 #define QSPI_SCR_DLYBS_MASK             GENMASK(23, 16)
 #define QSPI_SCR_DLYBS(n)               (((n) << 16) & QSPI_SCR_DLYBS_MASK)
 
-/* Bitfields in QSPI_ICR (Instruction Code Register) */
+/* Bitfields in QSPI_ICR (Read/Write Instruction Code Register) */
 #define QSPI_ICR_INST_MASK              GENMASK(7, 0)
 #define QSPI_ICR_INST(inst)             (((inst) << 0) & QSPI_ICR_INST_MASK)
 #define QSPI_ICR_OPT_MASK               GENMASK(23, 16)
@@ -125,14 +116,12 @@
 #define QSPI_IFR_OPTL_4BIT              (2 << 8)
 #define QSPI_IFR_OPTL_8BIT              (3 << 8)
 #define QSPI_IFR_ADDRL                  BIT(10)
-#define QSPI_IFR_TFRTYP_MASK            GENMASK(13, 12)
-#define QSPI_IFR_TFRTYP_TRSFR_READ      (0 << 12)
-#define QSPI_IFR_TFRTYP_TRSFR_READ_MEM  (1 << 12)
-#define QSPI_IFR_TFRTYP_TRSFR_WRITE     (2 << 12)
-#define QSPI_IFR_TFRTYP_TRSFR_WRITE_MEM (3 << 13)
+#define QSPI_IFR_TFRTYP_MEM		BIT(12)
+#define QSPI_IFR_SAMA5D2_WRITE_TRSFR	BIT(13)
 #define QSPI_IFR_CRM                    BIT(14)
 #define QSPI_IFR_NBDUM_MASK             GENMASK(20, 16)
 #define QSPI_IFR_NBDUM(n)               (((n) << 16) & QSPI_IFR_NBDUM_MASK)
+#define QSPI_IFR_APBTFRTYP_READ		BIT(24)	/* Defined in SAM9X60 */
 
 /* Bitfields in QSPI_SMR (Scrambling Mode Register) */
 #define QSPI_SMR_SCREN                  BIT(0)
@@ -148,24 +137,31 @@
 #define QSPI_WPSR_WPVSRC_MASK           GENMASK(15, 8)
 #define QSPI_WPSR_WPVSRC(src)           (((src) << 8) & QSPI_WPSR_WPVSRC)
 
+struct atmel_qspi_caps {
+	bool has_qspick;
+	bool has_ricr;
+};
 
 struct atmel_qspi {
 	void __iomem		*regs;
 	void __iomem		*mem;
-	struct clk		*clk;
+	struct clk		*pclk;
+	struct clk		*qspick;
 	struct platform_device	*pdev;
+	const struct atmel_qspi_caps *caps;
 	u32			pending;
+	u32			mr;
 	struct completion	cmd_completion;
 };
 
-struct qspi_mode {
+struct atmel_qspi_mode {
 	u8 cmd_buswidth;
 	u8 addr_buswidth;
 	u8 data_buswidth;
 	u32 config;
 };
 
-static const struct qspi_mode sama5d2_qspi_modes[] = {
+static const struct atmel_qspi_mode atmel_qspi_modes[] = {
 	{ 1, 1, 1, QSPI_IFR_WIDTH_SINGLE_BIT_SPI },
 	{ 1, 1, 2, QSPI_IFR_WIDTH_DUAL_OUTPUT },
 	{ 1, 1, 4, QSPI_IFR_WIDTH_QUAD_OUTPUT },
@@ -175,19 +171,8 @@ static const struct qspi_mode sama5d2_qspi_modes[] = {
 	{ 4, 4, 4, QSPI_IFR_WIDTH_QUAD_CMD },
 };
 
-/* Register access functions */
-static inline u32 qspi_readl(struct atmel_qspi *aq, u32 reg)
-{
-	return readl_relaxed(aq->regs + reg);
-}
-
-static inline void qspi_writel(struct atmel_qspi *aq, u32 reg, u32 value)
-{
-	writel_relaxed(value, aq->regs + reg);
-}
-
-static inline bool is_compatible(const struct spi_mem_op *op,
-				 const struct qspi_mode *mode)
+static inline bool atmel_qspi_is_compatible(const struct spi_mem_op *op,
+					    const struct atmel_qspi_mode *mode)
 {
 	if (op->cmd.buswidth != mode->cmd_buswidth)
 		return false;
@@ -201,21 +186,21 @@ static inline bool is_compatible(const struct spi_mem_op *op,
 	return true;
 }
 
-static int find_mode(const struct spi_mem_op *op)
+static int atmel_qspi_find_mode(const struct spi_mem_op *op)
 {
 	u32 i;
 
-	for (i = 0; i < ARRAY_SIZE(sama5d2_qspi_modes); i++)
-		if (is_compatible(op, &sama5d2_qspi_modes[i]))
+	for (i = 0; i < ARRAY_SIZE(atmel_qspi_modes); i++)
+		if (atmel_qspi_is_compatible(op, &atmel_qspi_modes[i]))
 			return i;
 
-	return -1;
+	return -ENOTSUPP;
 }
 
 static bool atmel_qspi_supports_op(struct spi_mem *mem,
 				   const struct spi_mem_op *op)
 {
-	if (find_mode(op) < 0)
+	if (atmel_qspi_find_mode(op) < 0)
 		return false;
 
 	/* special case not supported by hardware */
@@ -226,29 +211,37 @@ static bool atmel_qspi_supports_op(struct spi_mem *mem,
 	return true;
 }
 
-static int atmel_qspi_exec_op(struct spi_mem *mem, const struct spi_mem_op *op)
+static int atmel_qspi_set_cfg(struct atmel_qspi *aq,
+			      const struct spi_mem_op *op, u32 *offset)
 {
-	struct atmel_qspi *aq = spi_controller_get_devdata(mem->spi->master);
-	int mode;
+	u32 iar, icr, ifr;
 	u32 dummy_cycles = 0;
-	u32 iar, icr, ifr, sr;
-	int err = 0;
+	int mode;
 
 	iar = 0;
 	icr = QSPI_ICR_INST(op->cmd.opcode);
 	ifr = QSPI_IFR_INSTEN;
 
-	qspi_writel(aq, QSPI_MR, QSPI_MR_SMM);
-
-	mode = find_mode(op);
+	mode = atmel_qspi_find_mode(op);
 	if (mode < 0)
-		return -ENOTSUPP;
-
-	ifr |= sama5d2_qspi_modes[mode].config;
+		return mode;
+	ifr |= atmel_qspi_modes[mode].config;
 
 	if (op->dummy.buswidth && op->dummy.nbytes)
 		dummy_cycles = op->dummy.nbytes * 8 / op->dummy.buswidth;
 
+	/*
+	 * The controller allows 24 and 32-bit addressing while NAND-flash
+	 * requires 16-bit long. Handling 8-bit long addresses is done using
+	 * the option field. For the 16-bit addresses, the workaround depends
+	 * of the number of requested dummy bits. If there are 8 or more dummy
+	 * cycles, the address is shifted and sent with the first dummy byte.
+	 * Otherwise opcode is disabled and the first byte of the address
+	 * contains the command opcode (works only if the opcode and address
+	 * use the same buswidth). The limitation is when the 16-bit address is
+	 * used without enough dummy cycles and the opcode is using a different
+	 * buswidth than the address.
+	 */
 	if (op->addr.buswidth) {
 		switch (op->addr.nbytes) {
 		case 0:
@@ -282,6 +275,9 @@ static int atmel_qspi_exec_op(struct spi_mem *mem, const struct spi_mem_op *op)
 		}
 	}
 
+	/* offset of the data access in the QSPI memory space */
+	*offset = iar;
+
 	/* Set number of dummy cycles */
 	if (dummy_cycles)
 		ifr |= QSPI_IFR_NBDUM(dummy_cycles);
@@ -290,49 +286,82 @@ static int atmel_qspi_exec_op(struct spi_mem *mem, const struct spi_mem_op *op)
 	if (op->data.nbytes)
 		ifr |= QSPI_IFR_DATAEN;
 
-	if (op->data.dir == SPI_MEM_DATA_IN && op->data.nbytes)
-		ifr |= QSPI_IFR_TFRTYP_TRSFR_READ;
-	else
-		ifr |= QSPI_IFR_TFRTYP_TRSFR_WRITE;
+	/*
+	 * If the QSPI controller is set in regular SPI mode, set it in
+	 * Serial Memory Mode (SMM).
+	 */
+	if (aq->mr != QSPI_MR_SMM) {
+		writel_relaxed(QSPI_MR_SMM, aq->regs + QSPI_MR);
+		aq->mr = QSPI_MR_SMM;
+	}
 
 	/* Clear pending interrupts */
-	(void)qspi_readl(aq, QSPI_SR);
+	(void)readl_relaxed(aq->regs + QSPI_SR);
+
+	if (aq->caps->has_ricr) {
+		if (!op->addr.nbytes && op->data.dir == SPI_MEM_DATA_IN)
+			ifr |= QSPI_IFR_APBTFRTYP_READ;
 
-	/* Set QSPI Instruction Frame registers */
-	qspi_writel(aq, QSPI_IAR, iar);
-	qspi_writel(aq, QSPI_ICR, icr);
-	qspi_writel(aq, QSPI_IFR, ifr);
+		/* Set QSPI Instruction Frame registers */
+		writel_relaxed(iar, aq->regs + QSPI_IAR);
+		if (op->data.dir == SPI_MEM_DATA_IN)
+			writel_relaxed(icr, aq->regs + QSPI_RICR);
+		else
+			writel_relaxed(icr, aq->regs + QSPI_WICR);
+		writel_relaxed(ifr, aq->regs + QSPI_IFR);
+	} else {
+		if (op->data.dir == SPI_MEM_DATA_OUT)
+			ifr |= QSPI_IFR_SAMA5D2_WRITE_TRSFR;
+
+		/* Set QSPI Instruction Frame registers */
+		writel_relaxed(iar, aq->regs + QSPI_IAR);
+		writel_relaxed(icr, aq->regs + QSPI_ICR);
+		writel_relaxed(ifr, aq->regs + QSPI_IFR);
+	}
+
+	return 0;
+}
+
+static int atmel_qspi_exec_op(struct spi_mem *mem, const struct spi_mem_op *op)
+{
+	struct atmel_qspi *aq = spi_controller_get_devdata(mem->spi->master);
+	u32 sr, offset;
+	int err;
+
+	err = atmel_qspi_set_cfg(aq, op, &offset);
+	if (err)
+		return err;
 
 	/* Skip to the final steps if there is no data */
 	if (op->data.nbytes) {
 		/* Dummy read of QSPI_IFR to synchronize APB and AHB accesses */
-		(void)qspi_readl(aq, QSPI_IFR);
+		(void)readl_relaxed(aq->regs + QSPI_IFR);
 
 		/* Send/Receive data */
 		if (op->data.dir == SPI_MEM_DATA_IN)
-			_memcpy_fromio(op->data.buf.in,
-				aq->mem + iar, op->data.nbytes);
+			_memcpy_fromio(op->data.buf.in, aq->mem + offset,
+				       op->data.nbytes);
 		else
-			_memcpy_toio(aq->mem + iar,
-				op->data.buf.out, op->data.nbytes);
+			_memcpy_toio(aq->mem + offset, op->data.buf.out,
+				     op->data.nbytes);
 
 		/* Release the chip-select */
-		qspi_writel(aq, QSPI_CR, QSPI_CR_LASTXFER);
+		writel_relaxed(QSPI_CR_LASTXFER, aq->regs + QSPI_CR);
 	}
 
 	/* Poll INSTRuction End status */
-	sr = qspi_readl(aq, QSPI_SR);
+	sr = readl_relaxed(aq->regs + QSPI_SR);
 	if ((sr & QSPI_SR_CMD_COMPLETED) == QSPI_SR_CMD_COMPLETED)
 		return err;
 
 	/* Wait for INSTRuction End interrupt */
 	reinit_completion(&aq->cmd_completion);
 	aq->pending = sr & QSPI_SR_CMD_COMPLETED;
-	qspi_writel(aq, QSPI_IER, QSPI_SR_CMD_COMPLETED);
+	writel_relaxed(QSPI_SR_CMD_COMPLETED, aq->regs + QSPI_IER);
 	if (!wait_for_completion_timeout(&aq->cmd_completion,
 					 msecs_to_jiffies(1000)))
 		err = -ETIMEDOUT;
-	qspi_writel(aq, QSPI_IDR, QSPI_SR_CMD_COMPLETED);
+	writel_relaxed(QSPI_SR_CMD_COMPLETED, aq->regs + QSPI_IDR);
 
 	return err;
 }
@@ -361,7 +390,7 @@ static int atmel_qspi_setup(struct spi_device *spi)
 	if (!spi->max_speed_hz)
 		return -EINVAL;
 
-	src_rate = clk_get_rate(aq->clk);
+	src_rate = clk_get_rate(aq->pclk);
 	if (!src_rate)
 		return -EINVAL;
 
@@ -371,7 +400,7 @@ static int atmel_qspi_setup(struct spi_device *spi)
 		scbr--;
 
 	scr = QSPI_SCR_SCBR(scbr);
-	qspi_writel(aq, QSPI_SCR, scr);
+	writel_relaxed(scr, aq->regs + QSPI_SCR);
 
 	return 0;
 }
@@ -379,21 +408,25 @@ static int atmel_qspi_setup(struct spi_device *spi)
 static int atmel_qspi_init(struct atmel_qspi *aq)
 {
 	/* Reset the QSPI controller */
-	qspi_writel(aq, QSPI_CR, QSPI_CR_SWRST);
+	writel_relaxed(QSPI_CR_SWRST, aq->regs + QSPI_CR);
+
+	/* Set the QSPI controller by default in Serial Memory Mode */
+	writel_relaxed(QSPI_MR_SMM, aq->regs + QSPI_MR);
+	aq->mr = QSPI_MR_SMM;
 
 	/* Enable the QSPI controller */
-	qspi_writel(aq, QSPI_CR, QSPI_CR_QSPIEN);
+	writel_relaxed(QSPI_CR_QSPIEN, aq->regs + QSPI_CR);
 
 	return 0;
 }
 
 static irqreturn_t atmel_qspi_interrupt(int irq, void *dev_id)
 {
-	struct atmel_qspi *aq = (struct atmel_qspi *)dev_id;
+	struct atmel_qspi *aq = dev_id;
 	u32 status, mask, pending;
 
-	status = qspi_readl(aq, QSPI_SR);
-	mask = qspi_readl(aq, QSPI_IMR);
+	status = readl_relaxed(aq->regs + QSPI_SR);
+	mask = readl_relaxed(aq->regs + QSPI_IMR);
 	pending = status & mask;
 
 	if (!pending)
@@ -449,44 +482,74 @@ static int atmel_qspi_probe(struct platform_device *pdev)
 	}
 
 	/* Get the peripheral clock */
-	aq->clk = devm_clk_get(&pdev->dev, NULL);
-	if (IS_ERR(aq->clk)) {
+	aq->pclk = devm_clk_get(&pdev->dev, "pclk");
+	if (IS_ERR(aq->pclk))
+		aq->pclk = devm_clk_get(&pdev->dev, NULL);
+
+	if (IS_ERR(aq->pclk)) {
 		dev_err(&pdev->dev, "missing peripheral clock\n");
-		err = PTR_ERR(aq->clk);
+		err = PTR_ERR(aq->pclk);
 		goto exit;
 	}
 
 	/* Enable the peripheral clock */
-	err = clk_prepare_enable(aq->clk);
+	err = clk_prepare_enable(aq->pclk);
 	if (err) {
 		dev_err(&pdev->dev, "failed to enable the peripheral clock\n");
 		goto exit;
 	}
 
+	aq->caps = of_device_get_match_data(&pdev->dev);
+	if (!aq->caps) {
+		dev_err(&pdev->dev, "Could not retrieve QSPI caps\n");
+		err = -EINVAL;
+		goto exit;
+	}
+
+	if (aq->caps->has_qspick) {
+		/* Get the QSPI system clock */
+		aq->qspick = devm_clk_get(&pdev->dev, "qspick");
+		if (IS_ERR(aq->qspick)) {
+			dev_err(&pdev->dev, "missing system clock\n");
+			err = PTR_ERR(aq->qspick);
+			goto disable_pclk;
+		}
+
+		/* Enable the QSPI system clock */
+		err = clk_prepare_enable(aq->qspick);
+		if (err) {
+			dev_err(&pdev->dev,
+				"failed to enable the QSPI system clock\n");
+			goto disable_pclk;
+		}
+	}
+
 	/* Request the IRQ */
 	irq = platform_get_irq(pdev, 0);
 	if (irq < 0) {
 		dev_err(&pdev->dev, "missing IRQ\n");
 		err = irq;
-		goto disable_clk;
+		goto disable_qspick;
 	}
 	err = devm_request_irq(&pdev->dev, irq, atmel_qspi_interrupt,
 			       0, dev_name(&pdev->dev), aq);
 	if (err)
-		goto disable_clk;
+		goto disable_qspick;
 
 	err = atmel_qspi_init(aq);
 	if (err)
-		goto disable_clk;
+		goto disable_qspick;
 
 	err = spi_register_controller(ctrl);
 	if (err)
-		goto disable_clk;
+		goto disable_qspick;
 
 	return 0;
 
-disable_clk:
-	clk_disable_unprepare(aq->clk);
+disable_qspick:
+	clk_disable_unprepare(aq->qspick);
+disable_pclk:
+	clk_disable_unprepare(aq->pclk);
 exit:
 	spi_controller_put(ctrl);
 
@@ -499,8 +562,9 @@ static int atmel_qspi_remove(struct platform_device *pdev)
 	struct atmel_qspi *aq = spi_controller_get_devdata(ctrl);
 
 	spi_unregister_controller(ctrl);
-	qspi_writel(aq, QSPI_CR, QSPI_CR_QSPIDIS);
-	clk_disable_unprepare(aq->clk);
+	writel_relaxed(QSPI_CR_QSPIDIS, aq->regs + QSPI_CR);
+	clk_disable_unprepare(aq->qspick);
+	clk_disable_unprepare(aq->pclk);
 	return 0;
 }
 
@@ -508,7 +572,8 @@ static int __maybe_unused atmel_qspi_suspend(struct device *dev)
 {
 	struct atmel_qspi *aq = dev_get_drvdata(dev);
 
-	clk_disable_unprepare(aq->clk);
+	clk_disable_unprepare(aq->qspick);
+	clk_disable_unprepare(aq->pclk);
 
 	return 0;
 }
@@ -517,7 +582,8 @@ static int __maybe_unused atmel_qspi_resume(struct device *dev)
 {
 	struct atmel_qspi *aq = dev_get_drvdata(dev);
 
-	clk_prepare_enable(aq->clk);
+	clk_prepare_enable(aq->pclk);
+	clk_prepare_enable(aq->qspick);
 
 	return atmel_qspi_init(aq);
 }
@@ -525,8 +591,22 @@ static int __maybe_unused atmel_qspi_resume(struct device *dev)
 static SIMPLE_DEV_PM_OPS(atmel_qspi_pm_ops, atmel_qspi_suspend,
 			 atmel_qspi_resume);
 
+static const struct atmel_qspi_caps atmel_sama5d2_qspi_caps = {};
+
+static const struct atmel_qspi_caps atmel_sam9x60_qspi_caps = {
+	.has_qspick = true,
+	.has_ricr = true,
+};
+
 static const struct of_device_id atmel_qspi_dt_ids[] = {
-	{ .compatible = "atmel,sama5d2-qspi" },
+	{
+		.compatible = "atmel,sama5d2-qspi",
+		.data = &atmel_sama5d2_qspi_caps,
+	},
+	{
+		.compatible = "microchip,sam9x60-qspi",
+		.data = &atmel_sam9x60_qspi_caps,
+	},
 	{ /* sentinel */ }
 };
 
diff --git a/drivers/spi/spi-ath79.c b/drivers/spi/spi-ath79.c
index 3f6b657394de..847f354ebef1 100644
--- a/drivers/spi/spi-ath79.c
+++ b/drivers/spi/spi-ath79.c
@@ -21,18 +21,26 @@
 #include <linux/spi/spi.h>
 #include <linux/spi/spi_bitbang.h>
 #include <linux/bitops.h>
-#include <linux/gpio.h>
 #include <linux/clk.h>
 #include <linux/err.h>
-
-#include <asm/mach-ath79/ar71xx_regs.h>
-#include <asm/mach-ath79/ath79_spi_platform.h>
+#include <linux/platform_data/spi-ath79.h>
 
 #define DRV_NAME	"ath79-spi"
 
 #define ATH79_SPI_RRW_DELAY_FACTOR	12000
 #define MHZ				(1000 * 1000)
 
+#define AR71XX_SPI_REG_FS		0x00	/* Function Select */
+#define AR71XX_SPI_REG_CTRL		0x04	/* SPI Control */
+#define AR71XX_SPI_REG_IOC		0x08	/* SPI I/O Control */
+#define AR71XX_SPI_REG_RDS		0x0c	/* Read Data Shift */
+
+#define AR71XX_SPI_FS_GPIO		BIT(0)	/* Enable GPIO mode */
+
+#define AR71XX_SPI_IOC_DO		BIT(0)	/* Data Out pin */
+#define AR71XX_SPI_IOC_CLK		BIT(8)	/* CLK pin */
+#define AR71XX_SPI_IOC_CS(n)		BIT(16 + (n))
+
 struct ath79_spi {
 	struct spi_bitbang	bitbang;
 	u32			ioc_base;
@@ -67,31 +75,14 @@ static void ath79_spi_chipselect(struct spi_device *spi, int is_active)
 {
 	struct ath79_spi *sp = ath79_spidev_to_sp(spi);
 	int cs_high = (spi->mode & SPI_CS_HIGH) ? is_active : !is_active;
+	u32 cs_bit = AR71XX_SPI_IOC_CS(spi->chip_select);
 
-	if (is_active) {
-		/* set initial clock polarity */
-		if (spi->mode & SPI_CPOL)
-			sp->ioc_base |= AR71XX_SPI_IOC_CLK;
-		else
-			sp->ioc_base &= ~AR71XX_SPI_IOC_CLK;
-
-		ath79_spi_wr(sp, AR71XX_SPI_REG_IOC, sp->ioc_base);
-	}
-
-	if (gpio_is_valid(spi->cs_gpio)) {
-		/* SPI is normally active-low */
-		gpio_set_value_cansleep(spi->cs_gpio, cs_high);
-	} else {
-		u32 cs_bit = AR71XX_SPI_IOC_CS(spi->chip_select);
-
-		if (cs_high)
-			sp->ioc_base |= cs_bit;
-		else
-			sp->ioc_base &= ~cs_bit;
-
-		ath79_spi_wr(sp, AR71XX_SPI_REG_IOC, sp->ioc_base);
-	}
+	if (cs_high)
+		sp->ioc_base |= cs_bit;
+	else
+		sp->ioc_base &= ~cs_bit;
 
+	ath79_spi_wr(sp, AR71XX_SPI_REG_IOC, sp->ioc_base);
 }
 
 static void ath79_spi_enable(struct ath79_spi *sp)
@@ -103,6 +94,9 @@ static void ath79_spi_enable(struct ath79_spi *sp)
 	sp->reg_ctrl = ath79_spi_rr(sp, AR71XX_SPI_REG_CTRL);
 	sp->ioc_base = ath79_spi_rr(sp, AR71XX_SPI_REG_IOC);
 
+	/* clear clk and mosi in the base state */
+	sp->ioc_base &= ~(AR71XX_SPI_IOC_DO | AR71XX_SPI_IOC_CLK);
+
 	/* TODO: setup speed? */
 	ath79_spi_wr(sp, AR71XX_SPI_REG_CTRL, 0x43);
 }
@@ -115,66 +109,6 @@ static void ath79_spi_disable(struct ath79_spi *sp)
 	ath79_spi_wr(sp, AR71XX_SPI_REG_FS, 0);
 }
 
-static int ath79_spi_setup_cs(struct spi_device *spi)
-{
-	struct ath79_spi *sp = ath79_spidev_to_sp(spi);
-	int status;
-
-	status = 0;
-	if (gpio_is_valid(spi->cs_gpio)) {
-		unsigned long flags;
-
-		flags = GPIOF_DIR_OUT;
-		if (spi->mode & SPI_CS_HIGH)
-			flags |= GPIOF_INIT_LOW;
-		else
-			flags |= GPIOF_INIT_HIGH;
-
-		status = gpio_request_one(spi->cs_gpio, flags,
-					  dev_name(&spi->dev));
-	} else {
-		u32 cs_bit = AR71XX_SPI_IOC_CS(spi->chip_select);
-
-		if (spi->mode & SPI_CS_HIGH)
-			sp->ioc_base &= ~cs_bit;
-		else
-			sp->ioc_base |= cs_bit;
-
-		ath79_spi_wr(sp, AR71XX_SPI_REG_IOC, sp->ioc_base);
-	}
-
-	return status;
-}
-
-static void ath79_spi_cleanup_cs(struct spi_device *spi)
-{
-	if (gpio_is_valid(spi->cs_gpio))
-		gpio_free(spi->cs_gpio);
-}
-
-static int ath79_spi_setup(struct spi_device *spi)
-{
-	int status = 0;
-
-	if (!spi->controller_state) {
-		status = ath79_spi_setup_cs(spi);
-		if (status)
-			return status;
-	}
-
-	status = spi_bitbang_setup(spi);
-	if (status && !spi->controller_state)
-		ath79_spi_cleanup_cs(spi);
-
-	return status;
-}
-
-static void ath79_spi_cleanup(struct spi_device *spi)
-{
-	ath79_spi_cleanup_cs(spi);
-	spi_bitbang_cleanup(spi);
-}
-
 static u32 ath79_spi_txrx_mode0(struct spi_device *spi, unsigned int nsecs,
 			       u32 word, u8 bits, unsigned flags)
 {
@@ -225,9 +159,10 @@ static int ath79_spi_probe(struct platform_device *pdev)
 
 	pdata = dev_get_platdata(&pdev->dev);
 
+	master->use_gpio_descriptors = true;
 	master->bits_per_word_mask = SPI_BPW_RANGE_MASK(1, 32);
-	master->setup = ath79_spi_setup;
-	master->cleanup = ath79_spi_cleanup;
+	master->setup = spi_bitbang_setup;
+	master->cleanup = spi_bitbang_cleanup;
 	if (pdata) {
 		master->bus_num = pdata->bus_num;
 		master->num_chipselect = pdata->num_chipselect;
@@ -236,7 +171,6 @@ static int ath79_spi_probe(struct platform_device *pdev)
 	sp->bitbang.master = master;
 	sp->bitbang.chipselect = ath79_spi_chipselect;
 	sp->bitbang.txrx_word[SPI_MODE_0] = ath79_spi_txrx_mode0;
-	sp->bitbang.setup_transfer = spi_bitbang_setup_transfer;
 	sp->bitbang.flags = SPI_CS_HIGH;
 
 	r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
diff --git a/drivers/spi/spi-atmel.c b/drivers/spi/spi-atmel.c
index 74fddcd3282b..4954f0ab1606 100644
--- a/drivers/spi/spi-atmel.c
+++ b/drivers/spi/spi-atmel.c
@@ -23,8 +23,7 @@
 #include <linux/of.h>
 
 #include <linux/io.h>
-#include <linux/gpio.h>
-#include <linux/of_gpio.h>
+#include <linux/gpio/consumer.h>
 #include <linux/pinctrl/consumer.h>
 #include <linux/pm_runtime.h>
 
@@ -312,7 +311,7 @@ struct atmel_spi {
 
 /* Controller-specific per-slave state */
 struct atmel_spi_device {
-	unsigned int		npcs_pin;
+	struct gpio_desc	*npcs_pin;
 	u32			csr;
 };
 
@@ -355,7 +354,6 @@ static bool atmel_spi_is_v2(struct atmel_spi *as)
 static void cs_activate(struct atmel_spi *as, struct spi_device *spi)
 {
 	struct atmel_spi_device *asd = spi->controller_state;
-	unsigned active = spi->mode & SPI_CS_HIGH;
 	u32 mr;
 
 	if (atmel_spi_is_v2(as)) {
@@ -379,7 +377,7 @@ static void cs_activate(struct atmel_spi *as, struct spi_device *spi)
 
 		mr = spi_readl(as, MR);
 		if (as->use_cs_gpios)
-			gpio_set_value(asd->npcs_pin, active);
+			gpiod_set_value(asd->npcs_pin, 1);
 	} else {
 		u32 cpol = (spi->mode & SPI_CPOL) ? SPI_BIT(CPOL) : 0;
 		int i;
@@ -396,19 +394,16 @@ static void cs_activate(struct atmel_spi *as, struct spi_device *spi)
 		mr = spi_readl(as, MR);
 		mr = SPI_BFINS(PCS, ~(1 << spi->chip_select), mr);
 		if (as->use_cs_gpios && spi->chip_select != 0)
-			gpio_set_value(asd->npcs_pin, active);
+			gpiod_set_value(asd->npcs_pin, 1);
 		spi_writel(as, MR, mr);
 	}
 
-	dev_dbg(&spi->dev, "activate %u%s, mr %08x\n",
-			asd->npcs_pin, active ? " (high)" : "",
-			mr);
+	dev_dbg(&spi->dev, "activate NPCS, mr %08x\n", mr);
 }
 
 static void cs_deactivate(struct atmel_spi *as, struct spi_device *spi)
 {
 	struct atmel_spi_device *asd = spi->controller_state;
-	unsigned active = spi->mode & SPI_CS_HIGH;
 	u32 mr;
 
 	/* only deactivate *this* device; sometimes transfers to
@@ -420,14 +415,12 @@ static void cs_deactivate(struct atmel_spi *as, struct spi_device *spi)
 		spi_writel(as, MR, mr);
 	}
 
-	dev_dbg(&spi->dev, "DEactivate %u%s, mr %08x\n",
-			asd->npcs_pin, active ? " (low)" : "",
-			mr);
+	dev_dbg(&spi->dev, "DEactivate NPCS, mr %08x\n", mr);
 
 	if (!as->use_cs_gpios)
 		spi_writel(as, CR, SPI_BIT(LASTXFER));
 	else if (atmel_spi_is_v2(as) || spi->chip_select != 0)
-		gpio_set_value(asd->npcs_pin, !active);
+		gpiod_set_value(asd->npcs_pin, 0);
 }
 
 static void atmel_spi_lock(struct atmel_spi *as) __acquires(&as->lock)
@@ -1188,7 +1181,6 @@ static int atmel_spi_setup(struct spi_device *spi)
 	struct atmel_spi_device	*asd;
 	u32			csr;
 	unsigned int		bits = spi->bits_per_word;
-	unsigned int		npcs_pin;
 
 	as = spi_master_get_devdata(spi->master);
 
@@ -1209,21 +1201,14 @@ static int atmel_spi_setup(struct spi_device *spi)
 		csr |= SPI_BIT(CSAAT);
 
 	/* DLYBS is mostly irrelevant since we manage chipselect using GPIOs.
-	 *
-	 * DLYBCT would add delays between words, slowing down transfers.
-	 * It could potentially be useful to cope with DMA bottlenecks, but
-	 * in those cases it's probably best to just use a lower bitrate.
 	 */
 	csr |= SPI_BF(DLYBS, 0);
-	csr |= SPI_BF(DLYBCT, 0);
-
-	/* chipselect must have been muxed as GPIO (e.g. in board setup) */
-	npcs_pin = (unsigned long)spi->controller_data;
 
-	if (!as->use_cs_gpios)
-		npcs_pin = spi->chip_select;
-	else if (gpio_is_valid(spi->cs_gpio))
-		npcs_pin = spi->cs_gpio;
+	/* DLYBCT adds delays between words.  This is useful for slow devices
+	 * that need a bit of time to setup the next transfer.
+	 */
+	csr |= SPI_BF(DLYBCT,
+			(as->spi_clk / 1000000 * spi->word_delay_usecs) >> 5);
 
 	asd = spi->controller_state;
 	if (!asd) {
@@ -1231,11 +1216,21 @@ static int atmel_spi_setup(struct spi_device *spi)
 		if (!asd)
 			return -ENOMEM;
 
-		if (as->use_cs_gpios)
-			gpio_direction_output(npcs_pin,
-					      !(spi->mode & SPI_CS_HIGH));
+		/*
+		 * If use_cs_gpios is true this means that we have "cs-gpios"
+		 * defined in the device tree node so we should have
+		 * gotten the GPIO lines from the device tree inside the
+		 * SPI core. Warn if this is not the case but continue since
+		 * CS GPIOs are after all optional.
+		 */
+		if (as->use_cs_gpios) {
+			if (!spi->cs_gpiod) {
+				dev_err(&spi->dev,
+					"host claims to use CS GPIOs but no CS found in DT by the SPI core\n");
+			}
+			asd->npcs_pin = spi->cs_gpiod;
+		}
 
-		asd->npcs_pin = npcs_pin;
 		spi->controller_state = asd;
 	}
 
@@ -1473,41 +1468,6 @@ static void atmel_get_caps(struct atmel_spi *as)
 	as->caps.has_pdc_support = version < 0x212;
 }
 
-/*-------------------------------------------------------------------------*/
-static int atmel_spi_gpio_cs(struct platform_device *pdev)
-{
-	struct spi_master	*master = platform_get_drvdata(pdev);
-	struct atmel_spi	*as = spi_master_get_devdata(master);
-	struct device_node	*np = master->dev.of_node;
-	int			i;
-	int			ret = 0;
-	int			nb = 0;
-
-	if (!as->use_cs_gpios)
-		return 0;
-
-	if (!np)
-		return 0;
-
-	nb = of_gpio_named_count(np, "cs-gpios");
-	for (i = 0; i < nb; i++) {
-		int cs_gpio = of_get_named_gpio(pdev->dev.of_node,
-						"cs-gpios", i);
-
-		if (cs_gpio == -EPROBE_DEFER)
-			return cs_gpio;
-
-		if (gpio_is_valid(cs_gpio)) {
-			ret = devm_gpio_request(&pdev->dev, cs_gpio,
-						dev_name(&pdev->dev));
-			if (ret)
-				return ret;
-		}
-	}
-
-	return 0;
-}
-
 static void atmel_spi_init(struct atmel_spi *as)
 {
 	spi_writel(as, CR, SPI_BIT(SWRST));
@@ -1560,6 +1520,7 @@ static int atmel_spi_probe(struct platform_device *pdev)
 		goto out_free;
 
 	/* the spi->mode bits understood by this driver: */
+	master->use_gpio_descriptors = true;
 	master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH;
 	master->bits_per_word_mask = SPI_BPW_RANGE_MASK(8, 16);
 	master->dev.of_node = pdev->dev.of_node;
@@ -1592,6 +1553,11 @@ static int atmel_spi_probe(struct platform_device *pdev)
 
 	atmel_get_caps(as);
 
+	/*
+	 * If there are chip selects in the device tree, those will be
+	 * discovered by the SPI core when registering the SPI master
+	 * and assigned to each SPI device.
+	 */
 	as->use_cs_gpios = true;
 	if (atmel_spi_is_v2(as) &&
 	    pdev->dev.of_node &&
@@ -1600,10 +1566,6 @@ static int atmel_spi_probe(struct platform_device *pdev)
 		master->num_chipselect = 4;
 	}
 
-	ret = atmel_spi_gpio_cs(pdev);
-	if (ret)
-		goto out_unmap_regs;
-
 	as->use_dma = false;
 	as->use_pdc = false;
 	if (as->caps.has_dma_support) {
diff --git a/drivers/spi/spi-bcm2835aux.c b/drivers/spi/spi-bcm2835aux.c
index 671e374e1b01..f7e054848ca5 100644
--- a/drivers/spi/spi-bcm2835aux.c
+++ b/drivers/spi/spi-bcm2835aux.c
@@ -456,7 +456,7 @@ static int bcm2835aux_spi_probe(struct platform_device *pdev)
 	}
 
 	bs->clk = devm_clk_get(&pdev->dev, NULL);
-	if ((!bs->clk) || (IS_ERR(bs->clk))) {
+	if (IS_ERR(bs->clk)) {
 		err = PTR_ERR(bs->clk);
 		dev_err(&pdev->dev, "could not get clk: %d\n", err);
 		goto out_master_put;
diff --git a/drivers/spi/spi-bitbang.c b/drivers/spi/spi-bitbang.c
index f29176000b8d..dd9a8c54a693 100644
--- a/drivers/spi/spi-bitbang.c
+++ b/drivers/spi/spi-bitbang.c
@@ -213,19 +213,6 @@ int spi_bitbang_setup(struct spi_device *spi)
 
 	dev_dbg(&spi->dev, "%s, %u nsec/bit\n", __func__, 2 * cs->nsecs);
 
-	/* NOTE we _need_ to call chipselect() early, ideally with adapter
-	 * setup, unless the hardware defaults cooperate to avoid confusion
-	 * between normal (active low) and inverted chipselects.
-	 */
-
-	/* deselect chip (low or high) */
-	mutex_lock(&bitbang->lock);
-	if (!bitbang->busy) {
-		bitbang->chipselect(spi, BITBANG_CS_INACTIVE);
-		ndelay(cs->nsecs);
-	}
-	mutex_unlock(&bitbang->lock);
-
 	return 0;
 }
 EXPORT_SYMBOL_GPL(spi_bitbang_setup);
diff --git a/drivers/spi/spi-cadence.c b/drivers/spi/spi-cadence.c
index 7c88f74f7f47..43d0e79842ac 100644
--- a/drivers/spi/spi-cadence.c
+++ b/drivers/spi/spi-cadence.c
@@ -13,7 +13,7 @@
 
 #include <linux/clk.h>
 #include <linux/delay.h>
-#include <linux/gpio.h>
+#include <linux/gpio/consumer.h>
 #include <linux/interrupt.h>
 #include <linux/io.h>
 #include <linux/module.h>
@@ -128,10 +128,6 @@ struct cdns_spi {
 	u32 is_decoded_cs;
 };
 
-struct cdns_spi_device_data {
-	bool gpio_requested;
-};
-
 /* Macros for the SPI controller read/write */
 static inline u32 cdns_spi_read(struct cdns_spi *xspi, u32 offset)
 {
@@ -176,16 +172,16 @@ static void cdns_spi_init_hw(struct cdns_spi *xspi)
 /**
  * cdns_spi_chipselect - Select or deselect the chip select line
  * @spi:	Pointer to the spi_device structure
- * @is_high:	Select(0) or deselect (1) the chip select line
+ * @enable:	Select (1) or deselect (0) the chip select line
  */
-static void cdns_spi_chipselect(struct spi_device *spi, bool is_high)
+static void cdns_spi_chipselect(struct spi_device *spi, bool enable)
 {
 	struct cdns_spi *xspi = spi_master_get_devdata(spi->master);
 	u32 ctrl_reg;
 
 	ctrl_reg = cdns_spi_read(xspi, CDNS_SPI_CR);
 
-	if (is_high) {
+	if (!enable) {
 		/* Deselect the slave */
 		ctrl_reg |= CDNS_SPI_CR_SSCTRL;
 	} else {
@@ -469,64 +465,6 @@ static int cdns_unprepare_transfer_hardware(struct spi_master *master)
 	return 0;
 }
 
-static int cdns_spi_setup(struct spi_device *spi)
-{
-
-	int ret = -EINVAL;
-	struct cdns_spi_device_data *cdns_spi_data = spi_get_ctldata(spi);
-
-	/* this is a pin managed by the controller, leave it alone */
-	if (spi->cs_gpio == -ENOENT)
-		return 0;
-
-	/* this seems to be the first time we're here */
-	if (!cdns_spi_data) {
-		cdns_spi_data = kzalloc(sizeof(*cdns_spi_data), GFP_KERNEL);
-		if (!cdns_spi_data)
-			return -ENOMEM;
-		cdns_spi_data->gpio_requested = false;
-		spi_set_ctldata(spi, cdns_spi_data);
-	}
-
-	/* if we haven't done so, grab the gpio */
-	if (!cdns_spi_data->gpio_requested && gpio_is_valid(spi->cs_gpio)) {
-		ret = gpio_request_one(spi->cs_gpio,
-				       (spi->mode & SPI_CS_HIGH) ?
-				       GPIOF_OUT_INIT_LOW : GPIOF_OUT_INIT_HIGH,
-				       dev_name(&spi->dev));
-		if (ret)
-			dev_err(&spi->dev, "can't request chipselect gpio %d\n",
-				spi->cs_gpio);
-		else
-			cdns_spi_data->gpio_requested = true;
-	} else {
-		if (gpio_is_valid(spi->cs_gpio)) {
-			int mode = ((spi->mode & SPI_CS_HIGH) ?
-				    GPIOF_OUT_INIT_LOW : GPIOF_OUT_INIT_HIGH);
-
-			ret = gpio_direction_output(spi->cs_gpio, mode);
-			if (ret)
-				dev_err(&spi->dev, "chipselect gpio %d setup failed (%d)\n",
-					spi->cs_gpio, ret);
-		}
-	}
-
-	return ret;
-}
-
-static void cdns_spi_cleanup(struct spi_device *spi)
-{
-	struct cdns_spi_device_data *cdns_spi_data = spi_get_ctldata(spi);
-
-	if (cdns_spi_data) {
-		if (cdns_spi_data->gpio_requested)
-			gpio_free(spi->cs_gpio);
-		kfree(cdns_spi_data);
-		spi_set_ctldata(spi, NULL);
-	}
-
-}
-
 /**
  * cdns_spi_probe - Probe method for the SPI driver
  * @pdev:	Pointer to the platform_device structure
@@ -584,11 +522,6 @@ static int cdns_spi_probe(struct platform_device *pdev)
 		goto clk_dis_apb;
 	}
 
-	pm_runtime_use_autosuspend(&pdev->dev);
-	pm_runtime_set_autosuspend_delay(&pdev->dev, SPI_AUTOSUSPEND_TIMEOUT);
-	pm_runtime_set_active(&pdev->dev);
-	pm_runtime_enable(&pdev->dev);
-
 	ret = of_property_read_u32(pdev->dev.of_node, "num-cs", &num_cs);
 	if (ret < 0)
 		master->num_chipselect = CDNS_SPI_DEFAULT_NUM_CS;
@@ -603,8 +536,10 @@ static int cdns_spi_probe(struct platform_device *pdev)
 	/* SPI controller initializations */
 	cdns_spi_init_hw(xspi);
 
-	pm_runtime_mark_last_busy(&pdev->dev);
-	pm_runtime_put_autosuspend(&pdev->dev);
+	pm_runtime_set_active(&pdev->dev);
+	pm_runtime_enable(&pdev->dev);
+	pm_runtime_use_autosuspend(&pdev->dev);
+	pm_runtime_set_autosuspend_delay(&pdev->dev, SPI_AUTOSUSPEND_TIMEOUT);
 
 	irq = platform_get_irq(pdev, 0);
 	if (irq <= 0) {
@@ -621,13 +556,12 @@ static int cdns_spi_probe(struct platform_device *pdev)
 		goto clk_dis_all;
 	}
 
+	master->use_gpio_descriptors = true;
 	master->prepare_transfer_hardware = cdns_prepare_transfer_hardware;
 	master->prepare_message = cdns_prepare_message;
 	master->transfer_one = cdns_transfer_one;
 	master->unprepare_transfer_hardware = cdns_unprepare_transfer_hardware;
 	master->set_cs = cdns_spi_chipselect;
-	master->setup = cdns_spi_setup;
-	master->cleanup = cdns_spi_cleanup;
 	master->auto_runtime_pm = true;
 	master->mode_bits = SPI_CPOL | SPI_CPHA;
 
diff --git a/drivers/spi/spi-clps711x.c b/drivers/spi/spi-clps711x.c
index 18193df2eba8..8c03c409fc07 100644
--- a/drivers/spi/spi-clps711x.c
+++ b/drivers/spi/spi-clps711x.c
@@ -11,7 +11,7 @@
 
 #include <linux/io.h>
 #include <linux/clk.h>
-#include <linux/gpio.h>
+#include <linux/gpio/consumer.h>
 #include <linux/module.h>
 #include <linux/interrupt.h>
 #include <linux/platform_device.h>
@@ -36,25 +36,6 @@ struct spi_clps711x_data {
 	int			len;
 };
 
-static int spi_clps711x_setup(struct spi_device *spi)
-{
-	if (!spi->controller_state) {
-		int ret;
-
-		ret = devm_gpio_request(&spi->master->dev, spi->cs_gpio,
-					dev_name(&spi->master->dev));
-		if (ret)
-			return ret;
-
-		spi->controller_state = spi;
-	}
-
-	/* We are expect that SPI-device is not selected */
-	gpio_direction_output(spi->cs_gpio, !(spi->mode & SPI_CS_HIGH));
-
-	return 0;
-}
-
 static int spi_clps711x_prepare_message(struct spi_master *master,
 					struct spi_message *msg)
 {
@@ -125,11 +106,11 @@ static int spi_clps711x_probe(struct platform_device *pdev)
 	if (!master)
 		return -ENOMEM;
 
+	master->use_gpio_descriptors = true;
 	master->bus_num = -1;
 	master->mode_bits = SPI_CPHA | SPI_CS_HIGH;
 	master->bits_per_word_mask =  SPI_BPW_RANGE_MASK(1, 8);
 	master->dev.of_node = pdev->dev.of_node;
-	master->setup = spi_clps711x_setup;
 	master->prepare_message = spi_clps711x_prepare_message;
 	master->transfer_one = spi_clps711x_transfer_one;
 
diff --git a/drivers/spi/spi-davinci.c b/drivers/spi/spi-davinci.c
index 56adec83f8fc..eb246ebcfa3a 100644
--- a/drivers/spi/spi-davinci.c
+++ b/drivers/spi/spi-davinci.c
@@ -15,7 +15,7 @@
 
 #include <linux/interrupt.h>
 #include <linux/io.h>
-#include <linux/gpio.h>
+#include <linux/gpio/consumer.h>
 #include <linux/module.h>
 #include <linux/delay.h>
 #include <linux/platform_device.h>
@@ -25,7 +25,6 @@
 #include <linux/dma-mapping.h>
 #include <linux/of.h>
 #include <linux/of_device.h>
-#include <linux/of_gpio.h>
 #include <linux/spi/spi.h>
 #include <linux/spi/spi_bitbang.h>
 #include <linux/slab.h>
@@ -222,12 +221,17 @@ static void davinci_spi_chipselect(struct spi_device *spi, int value)
 	 * Board specific chip select logic decides the polarity and cs
 	 * line for the controller
 	 */
-	if (spi->cs_gpio >= 0) {
+	if (spi->cs_gpiod) {
+		/*
+		 * FIXME: is this code ever executed? This host does not
+		 * set SPI_MASTER_GPIO_SS so this chipselect callback should
+		 * not get called from the SPI core when we are using
+		 * GPIOs for chip select.
+		 */
 		if (value == BITBANG_CS_ACTIVE)
-			gpio_set_value(spi->cs_gpio, spi->mode & SPI_CS_HIGH);
+			gpiod_set_value(spi->cs_gpiod, 1);
 		else
-			gpio_set_value(spi->cs_gpio,
-				!(spi->mode & SPI_CS_HIGH));
+			gpiod_set_value(spi->cs_gpiod, 0);
 	} else {
 		if (value == BITBANG_CS_ACTIVE) {
 			if (!(spi->mode & SPI_CS_WORD))
@@ -418,30 +422,18 @@ static int davinci_spi_of_setup(struct spi_device *spi)
  */
 static int davinci_spi_setup(struct spi_device *spi)
 {
-	int retval = 0;
 	struct davinci_spi *dspi;
-	struct spi_master *master = spi->master;
 	struct device_node *np = spi->dev.of_node;
 	bool internal_cs = true;
 
 	dspi = spi_master_get_devdata(spi->master);
 
 	if (!(spi->mode & SPI_NO_CS)) {
-		if (np && (master->cs_gpios != NULL) && (spi->cs_gpio >= 0)) {
-			retval = gpio_direction_output(
-				      spi->cs_gpio, !(spi->mode & SPI_CS_HIGH));
+		if (np && spi->cs_gpiod)
 			internal_cs = false;
-		}
-
-		if (retval) {
-			dev_err(&spi->dev, "GPIO %d setup failed (%d)\n",
-				spi->cs_gpio, retval);
-			return retval;
-		}
 
-		if (internal_cs) {
+		if (internal_cs)
 			set_io_bits(dspi->base + SPIPC0, 1 << spi->chip_select);
-		}
 	}
 
 	if (spi->mode & SPI_READY)
@@ -962,6 +954,7 @@ static int davinci_spi_probe(struct platform_device *pdev)
 	if (ret)
 		goto free_master;
 
+	master->use_gpio_descriptors = true;
 	master->dev.of_node = pdev->dev.of_node;
 	master->bus_num = pdev->id;
 	master->num_chipselect = pdata->num_chipselect;
@@ -980,27 +973,6 @@ static int davinci_spi_probe(struct platform_device *pdev)
 	if (dspi->version == SPI_VERSION_2)
 		dspi->bitbang.flags |= SPI_READY;
 
-	if (pdev->dev.of_node) {
-		int i;
-
-		for (i = 0; i < pdata->num_chipselect; i++) {
-			int cs_gpio = of_get_named_gpio(pdev->dev.of_node,
-							"cs-gpios", i);
-
-			if (cs_gpio == -EPROBE_DEFER) {
-				ret = cs_gpio;
-				goto free_clk;
-			}
-
-			if (gpio_is_valid(cs_gpio)) {
-				ret = devm_gpio_request(&pdev->dev, cs_gpio,
-							dev_name(&pdev->dev));
-				if (ret)
-					goto free_clk;
-			}
-		}
-	}
-
 	dspi->bitbang.txrx_bufs = davinci_spi_bufs;
 
 	ret = davinci_spi_request_dma(dspi);
diff --git a/drivers/spi/spi-dw-mmio.c b/drivers/spi/spi-dw-mmio.c
index d0dd7814e997..4bd59a93d988 100644
--- a/drivers/spi/spi-dw-mmio.c
+++ b/drivers/spi/spi-dw-mmio.c
@@ -18,7 +18,6 @@
 #include <linux/mfd/syscon.h>
 #include <linux/module.h>
 #include <linux/of.h>
-#include <linux/of_gpio.h>
 #include <linux/of_platform.h>
 #include <linux/acpi.h>
 #include <linux/property.h>
@@ -185,27 +184,6 @@ static int dw_spi_mmio_probe(struct platform_device *pdev)
 
 	dws->num_cs = num_cs;
 
-	if (pdev->dev.of_node) {
-		int i;
-
-		for (i = 0; i < dws->num_cs; i++) {
-			int cs_gpio = of_get_named_gpio(pdev->dev.of_node,
-					"cs-gpios", i);
-
-			if (cs_gpio == -EPROBE_DEFER) {
-				ret = cs_gpio;
-				goto out;
-			}
-
-			if (gpio_is_valid(cs_gpio)) {
-				ret = devm_gpio_request(&pdev->dev, cs_gpio,
-						dev_name(&pdev->dev));
-				if (ret)
-					goto out;
-			}
-		}
-	}
-
 	init_func = device_get_match_data(&pdev->dev);
 	if (init_func) {
 		ret = init_func(pdev, dwsmmio);
diff --git a/drivers/spi/spi-dw.c b/drivers/spi/spi-dw.c
index 2e822a56576a..ac81025f86ab 100644
--- a/drivers/spi/spi-dw.c
+++ b/drivers/spi/spi-dw.c
@@ -20,7 +20,6 @@
 #include <linux/delay.h>
 #include <linux/slab.h>
 #include <linux/spi/spi.h>
-#include <linux/gpio.h>
 
 #include "spi-dw.h"
 
@@ -54,41 +53,41 @@ static ssize_t dw_spi_show_regs(struct file *file, char __user *user_buf,
 	if (!buf)
 		return 0;
 
-	len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
+	len += scnprintf(buf + len, SPI_REGS_BUFSIZE - len,
 			"%s registers:\n", dev_name(&dws->master->dev));
-	len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
+	len += scnprintf(buf + len, SPI_REGS_BUFSIZE - len,
 			"=================================\n");
-	len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
+	len += scnprintf(buf + len, SPI_REGS_BUFSIZE - len,
 			"CTRL0: \t\t0x%08x\n", dw_readl(dws, DW_SPI_CTRL0));
-	len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
+	len += scnprintf(buf + len, SPI_REGS_BUFSIZE - len,
 			"CTRL1: \t\t0x%08x\n", dw_readl(dws, DW_SPI_CTRL1));
-	len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
+	len += scnprintf(buf + len, SPI_REGS_BUFSIZE - len,
 			"SSIENR: \t0x%08x\n", dw_readl(dws, DW_SPI_SSIENR));
-	len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
+	len += scnprintf(buf + len, SPI_REGS_BUFSIZE - len,
 			"SER: \t\t0x%08x\n", dw_readl(dws, DW_SPI_SER));
-	len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
+	len += scnprintf(buf + len, SPI_REGS_BUFSIZE - len,
 			"BAUDR: \t\t0x%08x\n", dw_readl(dws, DW_SPI_BAUDR));
-	len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
+	len += scnprintf(buf + len, SPI_REGS_BUFSIZE - len,
 			"TXFTLR: \t0x%08x\n", dw_readl(dws, DW_SPI_TXFLTR));
-	len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
+	len += scnprintf(buf + len, SPI_REGS_BUFSIZE - len,
 			"RXFTLR: \t0x%08x\n", dw_readl(dws, DW_SPI_RXFLTR));
-	len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
+	len += scnprintf(buf + len, SPI_REGS_BUFSIZE - len,
 			"TXFLR: \t\t0x%08x\n", dw_readl(dws, DW_SPI_TXFLR));
-	len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
+	len += scnprintf(buf + len, SPI_REGS_BUFSIZE - len,
 			"RXFLR: \t\t0x%08x\n", dw_readl(dws, DW_SPI_RXFLR));
-	len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
+	len += scnprintf(buf + len, SPI_REGS_BUFSIZE - len,
 			"SR: \t\t0x%08x\n", dw_readl(dws, DW_SPI_SR));
-	len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
+	len += scnprintf(buf + len, SPI_REGS_BUFSIZE - len,
 			"IMR: \t\t0x%08x\n", dw_readl(dws, DW_SPI_IMR));
-	len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
+	len += scnprintf(buf + len, SPI_REGS_BUFSIZE - len,
 			"ISR: \t\t0x%08x\n", dw_readl(dws, DW_SPI_ISR));
-	len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
+	len += scnprintf(buf + len, SPI_REGS_BUFSIZE - len,
 			"DMACR: \t\t0x%08x\n", dw_readl(dws, DW_SPI_DMACR));
-	len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
+	len += scnprintf(buf + len, SPI_REGS_BUFSIZE - len,
 			"DMATDLR: \t0x%08x\n", dw_readl(dws, DW_SPI_DMATDLR));
-	len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
+	len += scnprintf(buf + len, SPI_REGS_BUFSIZE - len,
 			"DMARDLR: \t0x%08x\n", dw_readl(dws, DW_SPI_DMARDLR));
-	len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
+	len += scnprintf(buf + len, SPI_REGS_BUFSIZE - len,
 			"=================================\n");
 
 	ret = simple_read_from_buffer(user_buf, count, ppos, buf, len);
@@ -138,11 +137,10 @@ void dw_spi_set_cs(struct spi_device *spi, bool enable)
 	struct dw_spi *dws = spi_controller_get_devdata(spi->controller);
 	struct chip_data *chip = spi_get_ctldata(spi);
 
-	/* Chip select logic is inverted from spi_set_cs() */
 	if (chip && chip->cs_control)
-		chip->cs_control(!enable);
+		chip->cs_control(enable);
 
-	if (!enable)
+	if (enable)
 		dw_writel(dws, DW_SPI_SER, BIT(spi->chip_select));
 	else if (dws->cs_override)
 		dw_writel(dws, DW_SPI_SER, 0);
@@ -317,7 +315,8 @@ static int dw_spi_transfer_one(struct spi_controller *master,
 	/* Default SPI mode is SCPOL = 0, SCPH = 0 */
 	cr0 = (transfer->bits_per_word - 1)
 		| (chip->type << SPI_FRF_OFFSET)
-		| (spi->mode << SPI_MODE_OFFSET)
+		| ((((spi->mode & SPI_CPOL) ? 1 : 0) << SPI_SCOL_OFFSET) |
+			(((spi->mode & SPI_CPHA) ? 1 : 0) << SPI_SCPH_OFFSET))
 		| (chip->tmode << SPI_TMOD_OFFSET);
 
 	/*
@@ -397,7 +396,6 @@ static int dw_spi_setup(struct spi_device *spi)
 {
 	struct dw_spi_chip *chip_info = NULL;
 	struct chip_data *chip;
-	int ret;
 
 	/* Only alloc on first setup */
 	chip = spi_get_ctldata(spi);
@@ -425,13 +423,6 @@ static int dw_spi_setup(struct spi_device *spi)
 
 	chip->tmode = SPI_TMOD_TR;
 
-	if (gpio_is_valid(spi->cs_gpio)) {
-		ret = gpio_direction_output(spi->cs_gpio,
-				!(spi->mode & SPI_CS_HIGH));
-		if (ret)
-			return ret;
-	}
-
 	return 0;
 }
 
@@ -496,6 +487,7 @@ int dw_spi_add_host(struct device *dev, struct dw_spi *dws)
 		goto err_free_master;
 	}
 
+	master->use_gpio_descriptors = true;
 	master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_LOOP;
 	master->bits_per_word_mask =  SPI_BPW_RANGE_MASK(4, 16);
 	master->bus_num = dws->bus_num;
diff --git a/drivers/spi/spi-fsl-dspi.c b/drivers/spi/spi-fsl-dspi.c
index 5e10dc5c93a5..53335ccc98f6 100644
--- a/drivers/spi/spi-fsl-dspi.c
+++ b/drivers/spi/spi-fsl-dspi.c
@@ -67,7 +67,7 @@
 #define SPI_SR			0x2c
 #define SPI_SR_EOQF		0x10000000
 #define SPI_SR_TCFQF		0x80000000
-#define SPI_SR_CLEAR		0xdaad0000
+#define SPI_SR_CLEAR		0x9aaf0000
 
 #define SPI_RSER_TFFFE		BIT(25)
 #define SPI_RSER_TFFFD		BIT(24)
@@ -233,6 +233,9 @@ static u32 dspi_pop_tx_pushr(struct fsl_dspi *dspi)
 {
 	u16 cmd = dspi->tx_cmd, data = dspi_pop_tx(dspi);
 
+	if (spi_controller_is_slave(dspi->master))
+		return data;
+
 	if (dspi->len > 0)
 		cmd |= SPI_PUSHR_CMD_CONT;
 	return cmd << 16 | data;
@@ -329,6 +332,11 @@ static int dspi_next_xfer_dma_submit(struct fsl_dspi *dspi)
 	dma_async_issue_pending(dma->chan_rx);
 	dma_async_issue_pending(dma->chan_tx);
 
+	if (spi_controller_is_slave(dspi->master)) {
+		wait_for_completion_interruptible(&dspi->dma->cmd_rx_complete);
+		return 0;
+	}
+
 	time_left = wait_for_completion_timeout(&dspi->dma->cmd_tx_complete,
 					DMA_COMPLETION_TIMEOUT);
 	if (time_left == 0) {
@@ -798,14 +806,18 @@ static int dspi_setup(struct spi_device *spi)
 	ns_delay_scale(&pasc, &asc, sck_cs_delay, clkrate);
 
 	chip->ctar_val = SPI_CTAR_CPOL(spi->mode & SPI_CPOL ? 1 : 0)
-		| SPI_CTAR_CPHA(spi->mode & SPI_CPHA ? 1 : 0)
-		| SPI_CTAR_LSBFE(spi->mode & SPI_LSB_FIRST ? 1 : 0)
-		| SPI_CTAR_PCSSCK(pcssck)
-		| SPI_CTAR_CSSCK(cssck)
-		| SPI_CTAR_PASC(pasc)
-		| SPI_CTAR_ASC(asc)
-		| SPI_CTAR_PBR(pbr)
-		| SPI_CTAR_BR(br);
+		| SPI_CTAR_CPHA(spi->mode & SPI_CPHA ? 1 : 0);
+
+	if (!spi_controller_is_slave(dspi->master)) {
+		chip->ctar_val |= SPI_CTAR_LSBFE(spi->mode &
+						 SPI_LSB_FIRST ? 1 : 0)
+			| SPI_CTAR_PCSSCK(pcssck)
+			| SPI_CTAR_CSSCK(cssck)
+			| SPI_CTAR_PASC(pasc)
+			| SPI_CTAR_ASC(asc)
+			| SPI_CTAR_PBR(pbr)
+			| SPI_CTAR_BR(br);
+	}
 
 	spi_set_ctldata(spi, chip);
 
@@ -970,8 +982,13 @@ static const struct regmap_config dspi_xspi_regmap_config[] = {
 
 static void dspi_init(struct fsl_dspi *dspi)
 {
-	regmap_write(dspi->regmap, SPI_MCR, SPI_MCR_MASTER | SPI_MCR_PCSIS |
-		     (dspi->devtype_data->xspi_mode ? SPI_MCR_XSPI : 0));
+	unsigned int mcr = SPI_MCR_PCSIS |
+		(dspi->devtype_data->xspi_mode ? SPI_MCR_XSPI : 0);
+
+	if (!spi_controller_is_slave(dspi->master))
+		mcr |= SPI_MCR_MASTER;
+
+	regmap_write(dspi->regmap, SPI_MCR, mcr);
 	regmap_write(dspi->regmap, SPI_SR, SPI_SR_CLEAR);
 	if (dspi->devtype_data->xspi_mode)
 		regmap_write(dspi->regmap, SPI_CTARE(0),
@@ -1027,6 +1044,9 @@ static int dspi_probe(struct platform_device *pdev)
 		}
 		master->bus_num = bus_num;
 
+		if (of_property_read_bool(np, "spi-slave"))
+			master->slave = true;
+
 		dspi->devtype_data = of_device_get_match_data(&pdev->dev);
 		if (!dspi->devtype_data) {
 			dev_err(&pdev->dev, "can't get devtype_data\n");
diff --git a/drivers/spi/spi-fsl-lpspi.c b/drivers/spi/spi-fsl-lpspi.c
index 08dcc3c22e88..391863914043 100644
--- a/drivers/spi/spi-fsl-lpspi.c
+++ b/drivers/spi/spi-fsl-lpspi.c
@@ -48,10 +48,13 @@
 #define CR_RTF		BIT(8)
 #define CR_RST		BIT(1)
 #define CR_MEN		BIT(0)
+#define SR_MBF		BIT(24)
 #define SR_TCF		BIT(10)
+#define SR_FCF		BIT(9)
 #define SR_RDF		BIT(1)
 #define SR_TDF		BIT(0)
 #define IER_TCIE	BIT(10)
+#define IER_FCIE	BIT(9)
 #define IER_RDIE	BIT(1)
 #define IER_TDIE	BIT(0)
 #define CFGR1_PCSCFG	BIT(27)
@@ -59,6 +62,7 @@
 #define CFGR1_PCSPOL	BIT(8)
 #define CFGR1_NOSTALL	BIT(3)
 #define CFGR1_MASTER	BIT(0)
+#define FSR_RXCOUNT	(BIT(16)|BIT(17)|BIT(18))
 #define RSR_RXEMPTY	BIT(1)
 #define TCR_CPOL	BIT(31)
 #define TCR_CPHA	BIT(30)
@@ -161,28 +165,10 @@ static int lpspi_unprepare_xfer_hardware(struct spi_controller *controller)
 	return 0;
 }
 
-static int fsl_lpspi_txfifo_empty(struct fsl_lpspi_data *fsl_lpspi)
-{
-	u32 txcnt;
-	unsigned long orig_jiffies = jiffies;
-
-	do {
-		txcnt = readl(fsl_lpspi->base + IMX7ULP_FSR) & 0xff;
-
-		if (time_after(jiffies, orig_jiffies + msecs_to_jiffies(500))) {
-			dev_dbg(fsl_lpspi->dev, "txfifo empty timeout\n");
-			return -ETIMEDOUT;
-		}
-		cond_resched();
-
-	} while (txcnt);
-
-	return 0;
-}
-
 static void fsl_lpspi_write_tx_fifo(struct fsl_lpspi_data *fsl_lpspi)
 {
 	u8 txfifo_cnt;
+	u32 temp;
 
 	txfifo_cnt = readl(fsl_lpspi->base + IMX7ULP_FSR) & 0xff;
 
@@ -193,9 +179,15 @@ static void fsl_lpspi_write_tx_fifo(struct fsl_lpspi_data *fsl_lpspi)
 		txfifo_cnt++;
 	}
 
-	if (!fsl_lpspi->remain && (txfifo_cnt < fsl_lpspi->txfifosize))
-		writel(0, fsl_lpspi->base + IMX7ULP_TDR);
-	else
+	if (txfifo_cnt < fsl_lpspi->txfifosize) {
+		if (!fsl_lpspi->is_slave) {
+			temp = readl(fsl_lpspi->base + IMX7ULP_TCR);
+			temp &= ~TCR_CONTC;
+			writel(temp, fsl_lpspi->base + IMX7ULP_TCR);
+		}
+
+		fsl_lpspi_intctrl(fsl_lpspi, IER_FCIE);
+	} else
 		fsl_lpspi_intctrl(fsl_lpspi, IER_TDIE);
 }
 
@@ -276,10 +268,6 @@ static int fsl_lpspi_config(struct fsl_lpspi_data *fsl_lpspi)
 	u32 temp;
 	int ret;
 
-	temp = CR_RST;
-	writel(temp, fsl_lpspi->base + IMX7ULP_CR);
-	writel(0, fsl_lpspi->base + IMX7ULP_CR);
-
 	if (!fsl_lpspi->is_slave) {
 		ret = fsl_lpspi_set_bitrate(fsl_lpspi);
 		if (ret)
@@ -370,6 +358,24 @@ static int fsl_lpspi_wait_for_completion(struct spi_controller *controller)
 	return 0;
 }
 
+static int fsl_lpspi_reset(struct fsl_lpspi_data *fsl_lpspi)
+{
+	u32 temp;
+
+	/* Disable all interrupt */
+	fsl_lpspi_intctrl(fsl_lpspi, 0);
+
+	/* W1C for all flags in SR */
+	temp = 0x3F << 8;
+	writel(temp, fsl_lpspi->base + IMX7ULP_SR);
+
+	/* Clear FIFO and disable module */
+	temp = CR_RRF | CR_RTF;
+	writel(temp, fsl_lpspi->base + IMX7ULP_CR);
+
+	return 0;
+}
+
 static int fsl_lpspi_transfer_one(struct spi_controller *controller,
 				  struct spi_device *spi,
 				  struct spi_transfer *t)
@@ -391,11 +397,7 @@ static int fsl_lpspi_transfer_one(struct spi_controller *controller,
 	if (ret)
 		return ret;
 
-	ret = fsl_lpspi_txfifo_empty(fsl_lpspi);
-	if (ret)
-		return ret;
-
-	fsl_lpspi_read_rx_fifo(fsl_lpspi);
+	fsl_lpspi_reset(fsl_lpspi);
 
 	return 0;
 }
@@ -408,7 +410,6 @@ static int fsl_lpspi_transfer_one_msg(struct spi_controller *controller,
 	struct spi_device *spi = msg->spi;
 	struct spi_transfer *xfer;
 	bool is_first_xfer = true;
-	u32 temp;
 	int ret = 0;
 
 	msg->status = 0;
@@ -428,13 +429,6 @@ static int fsl_lpspi_transfer_one_msg(struct spi_controller *controller,
 	}
 
 complete:
-	if (!fsl_lpspi->is_slave) {
-		/* de-assert SS, then finalize current message */
-		temp = readl(fsl_lpspi->base + IMX7ULP_TCR);
-		temp &= ~TCR_CONTC;
-		writel(temp, fsl_lpspi->base + IMX7ULP_TCR);
-	}
-
 	msg->status = ret;
 	spi_finalize_current_message(controller);
 
@@ -443,20 +437,30 @@ static int fsl_lpspi_transfer_one_msg(struct spi_controller *controller,
 
 static irqreturn_t fsl_lpspi_isr(int irq, void *dev_id)
 {
+	u32 temp_SR, temp_IER;
 	struct fsl_lpspi_data *fsl_lpspi = dev_id;
-	u32 temp;
 
+	temp_IER = readl(fsl_lpspi->base + IMX7ULP_IER);
 	fsl_lpspi_intctrl(fsl_lpspi, 0);
-	temp = readl(fsl_lpspi->base + IMX7ULP_SR);
+	temp_SR = readl(fsl_lpspi->base + IMX7ULP_SR);
 
 	fsl_lpspi_read_rx_fifo(fsl_lpspi);
 
-	if (temp & SR_TDF) {
+	if ((temp_SR & SR_TDF) && (temp_IER & IER_TDIE)) {
 		fsl_lpspi_write_tx_fifo(fsl_lpspi);
+		return IRQ_HANDLED;
+	}
 
-		if (!fsl_lpspi->remain)
-			complete(&fsl_lpspi->xfer_done);
+	if (temp_SR & SR_MBF ||
+	    readl(fsl_lpspi->base + IMX7ULP_FSR) & FSR_RXCOUNT) {
+		writel(SR_FCF, fsl_lpspi->base + IMX7ULP_SR);
+		fsl_lpspi_intctrl(fsl_lpspi, IER_FCIE);
+		return IRQ_HANDLED;
+	}
 
+	if (temp_SR & SR_FCF && (temp_IER & IER_FCIE)) {
+		writel(SR_FCF, fsl_lpspi->base + IMX7ULP_SR);
+			complete(&fsl_lpspi->xfer_done);
 		return IRQ_HANDLED;
 	}
 
diff --git a/drivers/spi/spi-fsl-qspi.c b/drivers/spi/spi-fsl-qspi.c
new file mode 100644
index 000000000000..6a713f78a62e
--- /dev/null
+++ b/drivers/spi/spi-fsl-qspi.c
@@ -0,0 +1,966 @@
+// SPDX-License-Identifier: GPL-2.0+
+
+/*
+ * Freescale QuadSPI driver.
+ *
+ * Copyright (C) 2013 Freescale Semiconductor, Inc.
+ * Copyright (C) 2018 Bootlin
+ * Copyright (C) 2018 exceet electronics GmbH
+ * Copyright (C) 2018 Kontron Electronics GmbH
+ *
+ * Transition to SPI MEM interface:
+ * Authors:
+ *     Boris Brezillon <bbrezillon@kernel.org>
+ *     Frieder Schrempf <frieder.schrempf@kontron.de>
+ *     Yogesh Gaur <yogeshnarayan.gaur@nxp.com>
+ *     Suresh Gupta <suresh.gupta@nxp.com>
+ *
+ * Based on the original fsl-quadspi.c spi-nor driver:
+ * Author: Freescale Semiconductor, Inc.
+ *
+ */
+
+#include <linux/bitops.h>
+#include <linux/clk.h>
+#include <linux/completion.h>
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/errno.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/iopoll.h>
+#include <linux/jiffies.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <linux/pm_qos.h>
+#include <linux/sizes.h>
+
+#include <linux/spi/spi.h>
+#include <linux/spi/spi-mem.h>
+
+/*
+ * The driver only uses one single LUT entry, that is updated on
+ * each call of exec_op(). Index 0 is preset at boot with a basic
+ * read operation, so let's use the last entry (15).
+ */
+#define	SEQID_LUT			15
+
+/* Registers used by the driver */
+#define QUADSPI_MCR			0x00
+#define QUADSPI_MCR_RESERVED_MASK	GENMASK(19, 16)
+#define QUADSPI_MCR_MDIS_MASK		BIT(14)
+#define QUADSPI_MCR_CLR_TXF_MASK	BIT(11)
+#define QUADSPI_MCR_CLR_RXF_MASK	BIT(10)
+#define QUADSPI_MCR_DDR_EN_MASK		BIT(7)
+#define QUADSPI_MCR_END_CFG_MASK	GENMASK(3, 2)
+#define QUADSPI_MCR_SWRSTHD_MASK	BIT(1)
+#define QUADSPI_MCR_SWRSTSD_MASK	BIT(0)
+
+#define QUADSPI_IPCR			0x08
+#define QUADSPI_IPCR_SEQID(x)		((x) << 24)
+
+#define QUADSPI_BUF3CR			0x1c
+#define QUADSPI_BUF3CR_ALLMST_MASK	BIT(31)
+#define QUADSPI_BUF3CR_ADATSZ(x)	((x) << 8)
+#define QUADSPI_BUF3CR_ADATSZ_MASK	GENMASK(15, 8)
+
+#define QUADSPI_BFGENCR			0x20
+#define QUADSPI_BFGENCR_SEQID(x)	((x) << 12)
+
+#define QUADSPI_BUF0IND			0x30
+#define QUADSPI_BUF1IND			0x34
+#define QUADSPI_BUF2IND			0x38
+#define QUADSPI_SFAR			0x100
+
+#define QUADSPI_SMPR			0x108
+#define QUADSPI_SMPR_DDRSMP_MASK	GENMASK(18, 16)
+#define QUADSPI_SMPR_FSDLY_MASK		BIT(6)
+#define QUADSPI_SMPR_FSPHS_MASK		BIT(5)
+#define QUADSPI_SMPR_HSENA_MASK		BIT(0)
+
+#define QUADSPI_RBCT			0x110
+#define QUADSPI_RBCT_WMRK_MASK		GENMASK(4, 0)
+#define QUADSPI_RBCT_RXBRD_USEIPS	BIT(8)
+
+#define QUADSPI_TBDR			0x154
+
+#define QUADSPI_SR			0x15c
+#define QUADSPI_SR_IP_ACC_MASK		BIT(1)
+#define QUADSPI_SR_AHB_ACC_MASK		BIT(2)
+
+#define QUADSPI_FR			0x160
+#define QUADSPI_FR_TFF_MASK		BIT(0)
+
+#define QUADSPI_SPTRCLR			0x16c
+#define QUADSPI_SPTRCLR_IPPTRC		BIT(8)
+#define QUADSPI_SPTRCLR_BFPTRC		BIT(0)
+
+#define QUADSPI_SFA1AD			0x180
+#define QUADSPI_SFA2AD			0x184
+#define QUADSPI_SFB1AD			0x188
+#define QUADSPI_SFB2AD			0x18c
+#define QUADSPI_RBDR(x)			(0x200 + ((x) * 4))
+
+#define QUADSPI_LUTKEY			0x300
+#define QUADSPI_LUTKEY_VALUE		0x5AF05AF0
+
+#define QUADSPI_LCKCR			0x304
+#define QUADSPI_LCKER_LOCK		BIT(0)
+#define QUADSPI_LCKER_UNLOCK		BIT(1)
+
+#define QUADSPI_RSER			0x164
+#define QUADSPI_RSER_TFIE		BIT(0)
+
+#define QUADSPI_LUT_BASE		0x310
+#define QUADSPI_LUT_OFFSET		(SEQID_LUT * 4 * 4)
+#define QUADSPI_LUT_REG(idx) \
+	(QUADSPI_LUT_BASE + QUADSPI_LUT_OFFSET + (idx) * 4)
+
+/* Instruction set for the LUT register */
+#define LUT_STOP		0
+#define LUT_CMD			1
+#define LUT_ADDR		2
+#define LUT_DUMMY		3
+#define LUT_MODE		4
+#define LUT_MODE2		5
+#define LUT_MODE4		6
+#define LUT_FSL_READ		7
+#define LUT_FSL_WRITE		8
+#define LUT_JMP_ON_CS		9
+#define LUT_ADDR_DDR		10
+#define LUT_MODE_DDR		11
+#define LUT_MODE2_DDR		12
+#define LUT_MODE4_DDR		13
+#define LUT_FSL_READ_DDR	14
+#define LUT_FSL_WRITE_DDR	15
+#define LUT_DATA_LEARN		16
+
+/*
+ * The PAD definitions for LUT register.
+ *
+ * The pad stands for the number of IO lines [0:3].
+ * For example, the quad read needs four IO lines,
+ * so you should use LUT_PAD(4).
+ */
+#define LUT_PAD(x) (fls(x) - 1)
+
+/*
+ * Macro for constructing the LUT entries with the following
+ * register layout:
+ *
+ *  ---------------------------------------------------
+ *  | INSTR1 | PAD1 | OPRND1 | INSTR0 | PAD0 | OPRND0 |
+ *  ---------------------------------------------------
+ */
+#define LUT_DEF(idx, ins, pad, opr)					\
+	((((ins) << 10) | ((pad) << 8) | (opr)) << (((idx) % 2) * 16))
+
+/* Controller needs driver to swap endianness */
+#define QUADSPI_QUIRK_SWAP_ENDIAN	BIT(0)
+
+/* Controller needs 4x internal clock */
+#define QUADSPI_QUIRK_4X_INT_CLK	BIT(1)
+
+/*
+ * TKT253890, the controller needs the driver to fill the txfifo with
+ * 16 bytes at least to trigger a data transfer, even though the extra
+ * data won't be transferred.
+ */
+#define QUADSPI_QUIRK_TKT253890		BIT(2)
+
+/* TKT245618, the controller cannot wake up from wait mode */
+#define QUADSPI_QUIRK_TKT245618		BIT(3)
+
+/*
+ * Controller adds QSPI_AMBA_BASE (base address of the mapped memory)
+ * internally. No need to add it when setting SFXXAD and SFAR registers
+ */
+#define QUADSPI_QUIRK_BASE_INTERNAL	BIT(4)
+
+struct fsl_qspi_devtype_data {
+	unsigned int rxfifo;
+	unsigned int txfifo;
+	unsigned int ahb_buf_size;
+	unsigned int quirks;
+	bool little_endian;
+};
+
+static const struct fsl_qspi_devtype_data vybrid_data = {
+	.rxfifo = SZ_128,
+	.txfifo = SZ_64,
+	.ahb_buf_size = SZ_1K,
+	.quirks = QUADSPI_QUIRK_SWAP_ENDIAN,
+	.little_endian = true,
+};
+
+static const struct fsl_qspi_devtype_data imx6sx_data = {
+	.rxfifo = SZ_128,
+	.txfifo = SZ_512,
+	.ahb_buf_size = SZ_1K,
+	.quirks = QUADSPI_QUIRK_4X_INT_CLK | QUADSPI_QUIRK_TKT245618,
+	.little_endian = true,
+};
+
+static const struct fsl_qspi_devtype_data imx7d_data = {
+	.rxfifo = SZ_512,
+	.txfifo = SZ_512,
+	.ahb_buf_size = SZ_1K,
+	.quirks = QUADSPI_QUIRK_TKT253890 | QUADSPI_QUIRK_4X_INT_CLK,
+	.little_endian = true,
+};
+
+static const struct fsl_qspi_devtype_data imx6ul_data = {
+	.rxfifo = SZ_128,
+	.txfifo = SZ_512,
+	.ahb_buf_size = SZ_1K,
+	.quirks = QUADSPI_QUIRK_TKT253890 | QUADSPI_QUIRK_4X_INT_CLK,
+	.little_endian = true,
+};
+
+static const struct fsl_qspi_devtype_data ls1021a_data = {
+	.rxfifo = SZ_128,
+	.txfifo = SZ_64,
+	.ahb_buf_size = SZ_1K,
+	.quirks = 0,
+	.little_endian = false,
+};
+
+static const struct fsl_qspi_devtype_data ls2080a_data = {
+	.rxfifo = SZ_128,
+	.txfifo = SZ_64,
+	.ahb_buf_size = SZ_1K,
+	.quirks = QUADSPI_QUIRK_TKT253890 | QUADSPI_QUIRK_BASE_INTERNAL,
+	.little_endian = true,
+};
+
+struct fsl_qspi {
+	void __iomem *iobase;
+	void __iomem *ahb_addr;
+	u32 memmap_phy;
+	struct clk *clk, *clk_en;
+	struct device *dev;
+	struct completion c;
+	const struct fsl_qspi_devtype_data *devtype_data;
+	struct mutex lock;
+	struct pm_qos_request pm_qos_req;
+	int selected;
+};
+
+static inline int needs_swap_endian(struct fsl_qspi *q)
+{
+	return q->devtype_data->quirks & QUADSPI_QUIRK_SWAP_ENDIAN;
+}
+
+static inline int needs_4x_clock(struct fsl_qspi *q)
+{
+	return q->devtype_data->quirks & QUADSPI_QUIRK_4X_INT_CLK;
+}
+
+static inline int needs_fill_txfifo(struct fsl_qspi *q)
+{
+	return q->devtype_data->quirks & QUADSPI_QUIRK_TKT253890;
+}
+
+static inline int needs_wakeup_wait_mode(struct fsl_qspi *q)
+{
+	return q->devtype_data->quirks & QUADSPI_QUIRK_TKT245618;
+}
+
+static inline int needs_amba_base_offset(struct fsl_qspi *q)
+{
+	return !(q->devtype_data->quirks & QUADSPI_QUIRK_BASE_INTERNAL);
+}
+
+/*
+ * An IC bug makes it necessary to rearrange the 32-bit data.
+ * Later chips, such as IMX6SLX, have fixed this bug.
+ */
+static inline u32 fsl_qspi_endian_xchg(struct fsl_qspi *q, u32 a)
+{
+	return needs_swap_endian(q) ? __swab32(a) : a;
+}
+
+/*
+ * R/W functions for big- or little-endian registers:
+ * The QSPI controller's endianness is independent of
+ * the CPU core's endianness. So far, although the CPU
+ * core is little-endian the QSPI controller can use
+ * big-endian or little-endian.
+ */
+static void qspi_writel(struct fsl_qspi *q, u32 val, void __iomem *addr)
+{
+	if (q->devtype_data->little_endian)
+		iowrite32(val, addr);
+	else
+		iowrite32be(val, addr);
+}
+
+static u32 qspi_readl(struct fsl_qspi *q, void __iomem *addr)
+{
+	if (q->devtype_data->little_endian)
+		return ioread32(addr);
+
+	return ioread32be(addr);
+}
+
+static irqreturn_t fsl_qspi_irq_handler(int irq, void *dev_id)
+{
+	struct fsl_qspi *q = dev_id;
+	u32 reg;
+
+	/* clear interrupt */
+	reg = qspi_readl(q, q->iobase + QUADSPI_FR);
+	qspi_writel(q, reg, q->iobase + QUADSPI_FR);
+
+	if (reg & QUADSPI_FR_TFF_MASK)
+		complete(&q->c);
+
+	dev_dbg(q->dev, "QUADSPI_FR : 0x%.8x:0x%.8x\n", 0, reg);
+	return IRQ_HANDLED;
+}
+
+static int fsl_qspi_check_buswidth(struct fsl_qspi *q, u8 width)
+{
+	switch (width) {
+	case 1:
+	case 2:
+	case 4:
+		return 0;
+	}
+
+	return -ENOTSUPP;
+}
+
+static bool fsl_qspi_supports_op(struct spi_mem *mem,
+				 const struct spi_mem_op *op)
+{
+	struct fsl_qspi *q = spi_controller_get_devdata(mem->spi->master);
+	int ret;
+
+	ret = fsl_qspi_check_buswidth(q, op->cmd.buswidth);
+
+	if (op->addr.nbytes)
+		ret |= fsl_qspi_check_buswidth(q, op->addr.buswidth);
+
+	if (op->dummy.nbytes)
+		ret |= fsl_qspi_check_buswidth(q, op->dummy.buswidth);
+
+	if (op->data.nbytes)
+		ret |= fsl_qspi_check_buswidth(q, op->data.buswidth);
+
+	if (ret)
+		return false;
+
+	/*
+	 * The number of instructions needed for the op, needs
+	 * to fit into a single LUT entry.
+	 */
+	if (op->addr.nbytes +
+	   (op->dummy.nbytes ? 1:0) +
+	   (op->data.nbytes ? 1:0) > 6)
+		return false;
+
+	/* Max 64 dummy clock cycles supported */
+	if (op->dummy.nbytes &&
+	    (op->dummy.nbytes * 8 / op->dummy.buswidth > 64))
+		return false;
+
+	/* Max data length, check controller limits and alignment */
+	if (op->data.dir == SPI_MEM_DATA_IN &&
+	    (op->data.nbytes > q->devtype_data->ahb_buf_size ||
+	     (op->data.nbytes > q->devtype_data->rxfifo - 4 &&
+	      !IS_ALIGNED(op->data.nbytes, 8))))
+		return false;
+
+	if (op->data.dir == SPI_MEM_DATA_OUT &&
+	    op->data.nbytes > q->devtype_data->txfifo)
+		return false;
+
+	return true;
+}
+
+static void fsl_qspi_prepare_lut(struct fsl_qspi *q,
+				 const struct spi_mem_op *op)
+{
+	void __iomem *base = q->iobase;
+	u32 lutval[4] = {};
+	int lutidx = 1, i;
+
+	lutval[0] |= LUT_DEF(0, LUT_CMD, LUT_PAD(op->cmd.buswidth),
+			     op->cmd.opcode);
+
+	/*
+	 * For some unknown reason, using LUT_ADDR doesn't work in some
+	 * cases (at least with only one byte long addresses), so
+	 * let's use LUT_MODE to write the address bytes one by one
+	 */
+	for (i = 0; i < op->addr.nbytes; i++) {
+		u8 addrbyte = op->addr.val >> (8 * (op->addr.nbytes - i - 1));
+
+		lutval[lutidx / 2] |= LUT_DEF(lutidx, LUT_MODE,
+					      LUT_PAD(op->addr.buswidth),
+					      addrbyte);
+		lutidx++;
+	}
+
+	if (op->dummy.nbytes) {
+		lutval[lutidx / 2] |= LUT_DEF(lutidx, LUT_DUMMY,
+					      LUT_PAD(op->dummy.buswidth),
+					      op->dummy.nbytes * 8 /
+					      op->dummy.buswidth);
+		lutidx++;
+	}
+
+	if (op->data.nbytes) {
+		lutval[lutidx / 2] |= LUT_DEF(lutidx,
+					      op->data.dir == SPI_MEM_DATA_IN ?
+					      LUT_FSL_READ : LUT_FSL_WRITE,
+					      LUT_PAD(op->data.buswidth),
+					      0);
+		lutidx++;
+	}
+
+	lutval[lutidx / 2] |= LUT_DEF(lutidx, LUT_STOP, 0, 0);
+
+	/* unlock LUT */
+	qspi_writel(q, QUADSPI_LUTKEY_VALUE, q->iobase + QUADSPI_LUTKEY);
+	qspi_writel(q, QUADSPI_LCKER_UNLOCK, q->iobase + QUADSPI_LCKCR);
+
+	/* fill LUT */
+	for (i = 0; i < ARRAY_SIZE(lutval); i++)
+		qspi_writel(q, lutval[i], base + QUADSPI_LUT_REG(i));
+
+	/* lock LUT */
+	qspi_writel(q, QUADSPI_LUTKEY_VALUE, q->iobase + QUADSPI_LUTKEY);
+	qspi_writel(q, QUADSPI_LCKER_LOCK, q->iobase + QUADSPI_LCKCR);
+}
+
+static int fsl_qspi_clk_prep_enable(struct fsl_qspi *q)
+{
+	int ret;
+
+	ret = clk_prepare_enable(q->clk_en);
+	if (ret)
+		return ret;
+
+	ret = clk_prepare_enable(q->clk);
+	if (ret) {
+		clk_disable_unprepare(q->clk_en);
+		return ret;
+	}
+
+	if (needs_wakeup_wait_mode(q))
+		pm_qos_add_request(&q->pm_qos_req, PM_QOS_CPU_DMA_LATENCY, 0);
+
+	return 0;
+}
+
+static void fsl_qspi_clk_disable_unprep(struct fsl_qspi *q)
+{
+	if (needs_wakeup_wait_mode(q))
+		pm_qos_remove_request(&q->pm_qos_req);
+
+	clk_disable_unprepare(q->clk);
+	clk_disable_unprepare(q->clk_en);
+}
+
+/*
+ * If we have changed the content of the flash by writing or erasing, or if we
+ * read from flash with a different offset into the page buffer, we need to
+ * invalidate the AHB buffer. If we do not do so, we may read out the wrong
+ * data. The spec tells us reset the AHB domain and Serial Flash domain at
+ * the same time.
+ */
+static void fsl_qspi_invalidate(struct fsl_qspi *q)
+{
+	u32 reg;
+
+	reg = qspi_readl(q, q->iobase + QUADSPI_MCR);
+	reg |= QUADSPI_MCR_SWRSTHD_MASK | QUADSPI_MCR_SWRSTSD_MASK;
+	qspi_writel(q, reg, q->iobase + QUADSPI_MCR);
+
+	/*
+	 * The minimum delay : 1 AHB + 2 SFCK clocks.
+	 * Delay 1 us is enough.
+	 */
+	udelay(1);
+
+	reg &= ~(QUADSPI_MCR_SWRSTHD_MASK | QUADSPI_MCR_SWRSTSD_MASK);
+	qspi_writel(q, reg, q->iobase + QUADSPI_MCR);
+}
+
+static void fsl_qspi_select_mem(struct fsl_qspi *q, struct spi_device *spi)
+{
+	unsigned long rate = spi->max_speed_hz;
+	int ret;
+
+	if (q->selected == spi->chip_select)
+		return;
+
+	if (needs_4x_clock(q))
+		rate *= 4;
+
+	fsl_qspi_clk_disable_unprep(q);
+
+	ret = clk_set_rate(q->clk, rate);
+	if (ret)
+		return;
+
+	ret = fsl_qspi_clk_prep_enable(q);
+	if (ret)
+		return;
+
+	q->selected = spi->chip_select;
+
+	fsl_qspi_invalidate(q);
+}
+
+static void fsl_qspi_read_ahb(struct fsl_qspi *q, const struct spi_mem_op *op)
+{
+	memcpy_fromio(op->data.buf.in,
+		      q->ahb_addr + q->selected * q->devtype_data->ahb_buf_size,
+		      op->data.nbytes);
+}
+
+static void fsl_qspi_fill_txfifo(struct fsl_qspi *q,
+				 const struct spi_mem_op *op)
+{
+	void __iomem *base = q->iobase;
+	int i;
+	u32 val;
+
+	for (i = 0; i < ALIGN_DOWN(op->data.nbytes, 4); i += 4) {
+		memcpy(&val, op->data.buf.out + i, 4);
+		val = fsl_qspi_endian_xchg(q, val);
+		qspi_writel(q, val, base + QUADSPI_TBDR);
+	}
+
+	if (i < op->data.nbytes) {
+		memcpy(&val, op->data.buf.out + i, op->data.nbytes - i);
+		val = fsl_qspi_endian_xchg(q, val);
+		qspi_writel(q, val, base + QUADSPI_TBDR);
+	}
+
+	if (needs_fill_txfifo(q)) {
+		for (i = op->data.nbytes; i < 16; i += 4)
+			qspi_writel(q, 0, base + QUADSPI_TBDR);
+	}
+}
+
+static void fsl_qspi_read_rxfifo(struct fsl_qspi *q,
+			  const struct spi_mem_op *op)
+{
+	void __iomem *base = q->iobase;
+	int i;
+	u8 *buf = op->data.buf.in;
+	u32 val;
+
+	for (i = 0; i < ALIGN_DOWN(op->data.nbytes, 4); i += 4) {
+		val = qspi_readl(q, base + QUADSPI_RBDR(i / 4));
+		val = fsl_qspi_endian_xchg(q, val);
+		memcpy(buf + i, &val, 4);
+	}
+
+	if (i < op->data.nbytes) {
+		val = qspi_readl(q, base + QUADSPI_RBDR(i / 4));
+		val = fsl_qspi_endian_xchg(q, val);
+		memcpy(buf + i, &val, op->data.nbytes - i);
+	}
+}
+
+static int fsl_qspi_do_op(struct fsl_qspi *q, const struct spi_mem_op *op)
+{
+	void __iomem *base = q->iobase;
+	int err = 0;
+
+	init_completion(&q->c);
+
+	/*
+	 * Always start the sequence at the same index since we update
+	 * the LUT at each exec_op() call. And also specify the DATA
+	 * length, since it's has not been specified in the LUT.
+	 */
+	qspi_writel(q, op->data.nbytes | QUADSPI_IPCR_SEQID(SEQID_LUT),
+		    base + QUADSPI_IPCR);
+
+	/* Wait for the interrupt. */
+	if (!wait_for_completion_timeout(&q->c, msecs_to_jiffies(1000)))
+		err = -ETIMEDOUT;
+
+	if (!err && op->data.nbytes && op->data.dir == SPI_MEM_DATA_IN)
+		fsl_qspi_read_rxfifo(q, op);
+
+	return err;
+}
+
+static int fsl_qspi_readl_poll_tout(struct fsl_qspi *q, void __iomem *base,
+				    u32 mask, u32 delay_us, u32 timeout_us)
+{
+	u32 reg;
+
+	if (!q->devtype_data->little_endian)
+		mask = (u32)cpu_to_be32(mask);
+
+	return readl_poll_timeout(base, reg, !(reg & mask), delay_us,
+				  timeout_us);
+}
+
+static int fsl_qspi_exec_op(struct spi_mem *mem, const struct spi_mem_op *op)
+{
+	struct fsl_qspi *q = spi_controller_get_devdata(mem->spi->master);
+	void __iomem *base = q->iobase;
+	u32 addr_offset = 0;
+	int err = 0;
+
+	mutex_lock(&q->lock);
+
+	/* wait for the controller being ready */
+	fsl_qspi_readl_poll_tout(q, base + QUADSPI_SR, (QUADSPI_SR_IP_ACC_MASK |
+				 QUADSPI_SR_AHB_ACC_MASK), 10, 1000);
+
+	fsl_qspi_select_mem(q, mem->spi);
+
+	if (needs_amba_base_offset(q))
+		addr_offset = q->memmap_phy;
+
+	qspi_writel(q,
+		    q->selected * q->devtype_data->ahb_buf_size + addr_offset,
+		    base + QUADSPI_SFAR);
+
+	qspi_writel(q, qspi_readl(q, base + QUADSPI_MCR) |
+		    QUADSPI_MCR_CLR_RXF_MASK | QUADSPI_MCR_CLR_TXF_MASK,
+		    base + QUADSPI_MCR);
+
+	qspi_writel(q, QUADSPI_SPTRCLR_BFPTRC | QUADSPI_SPTRCLR_IPPTRC,
+		    base + QUADSPI_SPTRCLR);
+
+	fsl_qspi_prepare_lut(q, op);
+
+	/*
+	 * If we have large chunks of data, we read them through the AHB bus
+	 * by accessing the mapped memory. In all other cases we use
+	 * IP commands to access the flash.
+	 */
+	if (op->data.nbytes > (q->devtype_data->rxfifo - 4) &&
+	    op->data.dir == SPI_MEM_DATA_IN) {
+		fsl_qspi_read_ahb(q, op);
+	} else {
+		qspi_writel(q, QUADSPI_RBCT_WMRK_MASK |
+			    QUADSPI_RBCT_RXBRD_USEIPS, base + QUADSPI_RBCT);
+
+		if (op->data.nbytes && op->data.dir == SPI_MEM_DATA_OUT)
+			fsl_qspi_fill_txfifo(q, op);
+
+		err = fsl_qspi_do_op(q, op);
+	}
+
+	/* Invalidate the data in the AHB buffer. */
+	fsl_qspi_invalidate(q);
+
+	mutex_unlock(&q->lock);
+
+	return err;
+}
+
+static int fsl_qspi_adjust_op_size(struct spi_mem *mem, struct spi_mem_op *op)
+{
+	struct fsl_qspi *q = spi_controller_get_devdata(mem->spi->master);
+
+	if (op->data.dir == SPI_MEM_DATA_OUT) {
+		if (op->data.nbytes > q->devtype_data->txfifo)
+			op->data.nbytes = q->devtype_data->txfifo;
+	} else {
+		if (op->data.nbytes > q->devtype_data->ahb_buf_size)
+			op->data.nbytes = q->devtype_data->ahb_buf_size;
+		else if (op->data.nbytes > (q->devtype_data->rxfifo - 4))
+			op->data.nbytes = ALIGN_DOWN(op->data.nbytes, 8);
+	}
+
+	return 0;
+}
+
+static int fsl_qspi_default_setup(struct fsl_qspi *q)
+{
+	void __iomem *base = q->iobase;
+	u32 reg, addr_offset = 0;
+	int ret;
+
+	/* disable and unprepare clock to avoid glitch pass to controller */
+	fsl_qspi_clk_disable_unprep(q);
+
+	/* the default frequency, we will change it later if necessary. */
+	ret = clk_set_rate(q->clk, 66000000);
+	if (ret)
+		return ret;
+
+	ret = fsl_qspi_clk_prep_enable(q);
+	if (ret)
+		return ret;
+
+	/* Reset the module */
+	qspi_writel(q, QUADSPI_MCR_SWRSTSD_MASK | QUADSPI_MCR_SWRSTHD_MASK,
+		    base + QUADSPI_MCR);
+	udelay(1);
+
+	/* Disable the module */
+	qspi_writel(q, QUADSPI_MCR_MDIS_MASK | QUADSPI_MCR_RESERVED_MASK,
+		    base + QUADSPI_MCR);
+
+	reg = qspi_readl(q, base + QUADSPI_SMPR);
+	qspi_writel(q, reg & ~(QUADSPI_SMPR_FSDLY_MASK
+			| QUADSPI_SMPR_FSPHS_MASK
+			| QUADSPI_SMPR_HSENA_MASK
+			| QUADSPI_SMPR_DDRSMP_MASK), base + QUADSPI_SMPR);
+
+	/* We only use the buffer3 for AHB read */
+	qspi_writel(q, 0, base + QUADSPI_BUF0IND);
+	qspi_writel(q, 0, base + QUADSPI_BUF1IND);
+	qspi_writel(q, 0, base + QUADSPI_BUF2IND);
+
+	qspi_writel(q, QUADSPI_BFGENCR_SEQID(SEQID_LUT),
+		    q->iobase + QUADSPI_BFGENCR);
+	qspi_writel(q, QUADSPI_RBCT_WMRK_MASK, base + QUADSPI_RBCT);
+	qspi_writel(q, QUADSPI_BUF3CR_ALLMST_MASK |
+		    QUADSPI_BUF3CR_ADATSZ(q->devtype_data->ahb_buf_size / 8),
+		    base + QUADSPI_BUF3CR);
+
+	if (needs_amba_base_offset(q))
+		addr_offset = q->memmap_phy;
+
+	/*
+	 * In HW there can be a maximum of four chips on two buses with
+	 * two chip selects on each bus. We use four chip selects in SW
+	 * to differentiate between the four chips.
+	 * We use ahb_buf_size for each chip and set SFA1AD, SFA2AD, SFB1AD,
+	 * SFB2AD accordingly.
+	 */
+	qspi_writel(q, q->devtype_data->ahb_buf_size + addr_offset,
+		    base + QUADSPI_SFA1AD);
+	qspi_writel(q, q->devtype_data->ahb_buf_size * 2 + addr_offset,
+		    base + QUADSPI_SFA2AD);
+	qspi_writel(q, q->devtype_data->ahb_buf_size * 3 + addr_offset,
+		    base + QUADSPI_SFB1AD);
+	qspi_writel(q, q->devtype_data->ahb_buf_size * 4 + addr_offset,
+		    base + QUADSPI_SFB2AD);
+
+	q->selected = -1;
+
+	/* Enable the module */
+	qspi_writel(q, QUADSPI_MCR_RESERVED_MASK | QUADSPI_MCR_END_CFG_MASK,
+		    base + QUADSPI_MCR);
+
+	/* clear all interrupt status */
+	qspi_writel(q, 0xffffffff, q->iobase + QUADSPI_FR);
+
+	/* enable the interrupt */
+	qspi_writel(q, QUADSPI_RSER_TFIE, q->iobase + QUADSPI_RSER);
+
+	return 0;
+}
+
+static const char *fsl_qspi_get_name(struct spi_mem *mem)
+{
+	struct fsl_qspi *q = spi_controller_get_devdata(mem->spi->master);
+	struct device *dev = &mem->spi->dev;
+	const char *name;
+
+	/*
+	 * In order to keep mtdparts compatible with the old MTD driver at
+	 * mtd/spi-nor/fsl-quadspi.c, we set a custom name derived from the
+	 * platform_device of the controller.
+	 */
+	if (of_get_available_child_count(q->dev->of_node) == 1)
+		return dev_name(q->dev);
+
+	name = devm_kasprintf(dev, GFP_KERNEL,
+			      "%s-%d", dev_name(q->dev),
+			      mem->spi->chip_select);
+
+	if (!name) {
+		dev_err(dev, "failed to get memory for custom flash name\n");
+		return ERR_PTR(-ENOMEM);
+	}
+
+	return name;
+}
+
+static const struct spi_controller_mem_ops fsl_qspi_mem_ops = {
+	.adjust_op_size = fsl_qspi_adjust_op_size,
+	.supports_op = fsl_qspi_supports_op,
+	.exec_op = fsl_qspi_exec_op,
+	.get_name = fsl_qspi_get_name,
+};
+
+static int fsl_qspi_probe(struct platform_device *pdev)
+{
+	struct spi_controller *ctlr;
+	struct device *dev = &pdev->dev;
+	struct device_node *np = dev->of_node;
+	struct resource *res;
+	struct fsl_qspi *q;
+	int ret;
+
+	ctlr = spi_alloc_master(&pdev->dev, sizeof(*q));
+	if (!ctlr)
+		return -ENOMEM;
+
+	ctlr->mode_bits = SPI_RX_DUAL | SPI_RX_QUAD |
+			  SPI_TX_DUAL | SPI_TX_QUAD;
+
+	q = spi_controller_get_devdata(ctlr);
+	q->dev = dev;
+	q->devtype_data = of_device_get_match_data(dev);
+	if (!q->devtype_data) {
+		ret = -ENODEV;
+		goto err_put_ctrl;
+	}
+
+	platform_set_drvdata(pdev, q);
+
+	/* find the resources */
+	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "QuadSPI");
+	q->iobase = devm_ioremap_resource(dev, res);
+	if (IS_ERR(q->iobase)) {
+		ret = PTR_ERR(q->iobase);
+		goto err_put_ctrl;
+	}
+
+	res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
+					"QuadSPI-memory");
+	q->ahb_addr = devm_ioremap_resource(dev, res);
+	if (IS_ERR(q->ahb_addr)) {
+		ret = PTR_ERR(q->ahb_addr);
+		goto err_put_ctrl;
+	}
+
+	q->memmap_phy = res->start;
+
+	/* find the clocks */
+	q->clk_en = devm_clk_get(dev, "qspi_en");
+	if (IS_ERR(q->clk_en)) {
+		ret = PTR_ERR(q->clk_en);
+		goto err_put_ctrl;
+	}
+
+	q->clk = devm_clk_get(dev, "qspi");
+	if (IS_ERR(q->clk)) {
+		ret = PTR_ERR(q->clk);
+		goto err_put_ctrl;
+	}
+
+	ret = fsl_qspi_clk_prep_enable(q);
+	if (ret) {
+		dev_err(dev, "can not enable the clock\n");
+		goto err_put_ctrl;
+	}
+
+	/* find the irq */
+	ret = platform_get_irq(pdev, 0);
+	if (ret < 0) {
+		dev_err(dev, "failed to get the irq: %d\n", ret);
+		goto err_disable_clk;
+	}
+
+	ret = devm_request_irq(dev, ret,
+			fsl_qspi_irq_handler, 0, pdev->name, q);
+	if (ret) {
+		dev_err(dev, "failed to request irq: %d\n", ret);
+		goto err_disable_clk;
+	}
+
+	mutex_init(&q->lock);
+
+	ctlr->bus_num = -1;
+	ctlr->num_chipselect = 4;
+	ctlr->mem_ops = &fsl_qspi_mem_ops;
+
+	fsl_qspi_default_setup(q);
+
+	ctlr->dev.of_node = np;
+
+	ret = spi_register_controller(ctlr);
+	if (ret)
+		goto err_destroy_mutex;
+
+	return 0;
+
+err_destroy_mutex:
+	mutex_destroy(&q->lock);
+
+err_disable_clk:
+	fsl_qspi_clk_disable_unprep(q);
+
+err_put_ctrl:
+	spi_controller_put(ctlr);
+
+	dev_err(dev, "Freescale QuadSPI probe failed\n");
+	return ret;
+}
+
+static int fsl_qspi_remove(struct platform_device *pdev)
+{
+	struct fsl_qspi *q = platform_get_drvdata(pdev);
+
+	/* disable the hardware */
+	qspi_writel(q, QUADSPI_MCR_MDIS_MASK, q->iobase + QUADSPI_MCR);
+	qspi_writel(q, 0x0, q->iobase + QUADSPI_RSER);
+
+	fsl_qspi_clk_disable_unprep(q);
+
+	mutex_destroy(&q->lock);
+
+	return 0;
+}
+
+static int fsl_qspi_suspend(struct device *dev)
+{
+	return 0;
+}
+
+static int fsl_qspi_resume(struct device *dev)
+{
+	struct fsl_qspi *q = dev_get_drvdata(dev);
+
+	fsl_qspi_default_setup(q);
+
+	return 0;
+}
+
+static const struct of_device_id fsl_qspi_dt_ids[] = {
+	{ .compatible = "fsl,vf610-qspi", .data = &vybrid_data, },
+	{ .compatible = "fsl,imx6sx-qspi", .data = &imx6sx_data, },
+	{ .compatible = "fsl,imx7d-qspi", .data = &imx7d_data, },
+	{ .compatible = "fsl,imx6ul-qspi", .data = &imx6ul_data, },
+	{ .compatible = "fsl,ls1021a-qspi", .data = &ls1021a_data, },
+	{ .compatible = "fsl,ls2080a-qspi", .data = &ls2080a_data, },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, fsl_qspi_dt_ids);
+
+static const struct dev_pm_ops fsl_qspi_pm_ops = {
+	.suspend	= fsl_qspi_suspend,
+	.resume		= fsl_qspi_resume,
+};
+
+static struct platform_driver fsl_qspi_driver = {
+	.driver = {
+		.name	= "fsl-quadspi",
+		.of_match_table = fsl_qspi_dt_ids,
+		.pm =   &fsl_qspi_pm_ops,
+	},
+	.probe          = fsl_qspi_probe,
+	.remove		= fsl_qspi_remove,
+};
+module_platform_driver(fsl_qspi_driver);
+
+MODULE_DESCRIPTION("Freescale QuadSPI Controller Driver");
+MODULE_AUTHOR("Freescale Semiconductor Inc.");
+MODULE_AUTHOR("Boris Brezillon <bbrezillon@kernel.org>");
+MODULE_AUTHOR("Frieder Schrempf <frieder.schrempf@kontron.de>");
+MODULE_AUTHOR("Yogesh Gaur <yogeshnarayan.gaur@nxp.com>");
+MODULE_AUTHOR("Suresh Gupta <suresh.gupta@nxp.com>");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/spi/spi-geni-qcom.c b/drivers/spi/spi-geni-qcom.c
index fdb7cb88fb56..5f0b0d5bfef4 100644
--- a/drivers/spi/spi-geni-qcom.c
+++ b/drivers/spi/spi-geni-qcom.c
@@ -89,9 +89,6 @@ struct spi_geni_master {
 	int irq;
 };
 
-static void handle_fifo_timeout(struct spi_master *spi,
-				struct spi_message *msg);
-
 static int get_spi_clk_cfg(unsigned int speed_hz,
 			struct spi_geni_master *mas,
 			unsigned int *clk_idx,
@@ -122,6 +119,32 @@ static int get_spi_clk_cfg(unsigned int speed_hz,
 	return ret;
 }
 
+static void handle_fifo_timeout(struct spi_master *spi,
+				struct spi_message *msg)
+{
+	struct spi_geni_master *mas = spi_master_get_devdata(spi);
+	unsigned long time_left, flags;
+	struct geni_se *se = &mas->se;
+
+	spin_lock_irqsave(&mas->lock, flags);
+	reinit_completion(&mas->xfer_done);
+	mas->cur_mcmd = CMD_CANCEL;
+	geni_se_cancel_m_cmd(se);
+	writel(0, se->base + SE_GENI_TX_WATERMARK_REG);
+	spin_unlock_irqrestore(&mas->lock, flags);
+	time_left = wait_for_completion_timeout(&mas->xfer_done, HZ);
+	if (time_left)
+		return;
+
+	spin_lock_irqsave(&mas->lock, flags);
+	reinit_completion(&mas->xfer_done);
+	geni_se_abort_m_cmd(se);
+	spin_unlock_irqrestore(&mas->lock, flags);
+	time_left = wait_for_completion_timeout(&mas->xfer_done, HZ);
+	if (!time_left)
+		dev_err(mas->dev, "Failed to cancel/abort m_cmd\n");
+}
+
 static void spi_geni_set_cs(struct spi_device *slv, bool set_flag)
 {
 	struct spi_geni_master *mas = spi_master_get_devdata(slv->master);
@@ -233,7 +256,6 @@ static int spi_geni_prepare_message(struct spi_master *spi,
 	struct geni_se *se = &mas->se;
 
 	geni_se_select_mode(se, GENI_SE_FIFO);
-	reinit_completion(&mas->xfer_done);
 	ret = setup_fifo_params(spi_msg->spi, spi);
 	if (ret)
 		dev_err(mas->dev, "Couldn't select mode %d\n", ret);
@@ -357,32 +379,6 @@ static void setup_fifo_xfer(struct spi_transfer *xfer,
 		writel(mas->tx_wm, se->base + SE_GENI_TX_WATERMARK_REG);
 }
 
-static void handle_fifo_timeout(struct spi_master *spi,
-				struct spi_message *msg)
-{
-	struct spi_geni_master *mas = spi_master_get_devdata(spi);
-	unsigned long time_left, flags;
-	struct geni_se *se = &mas->se;
-
-	spin_lock_irqsave(&mas->lock, flags);
-	reinit_completion(&mas->xfer_done);
-	mas->cur_mcmd = CMD_CANCEL;
-	geni_se_cancel_m_cmd(se);
-	writel(0, se->base + SE_GENI_TX_WATERMARK_REG);
-	spin_unlock_irqrestore(&mas->lock, flags);
-	time_left = wait_for_completion_timeout(&mas->xfer_done, HZ);
-	if (time_left)
-		return;
-
-	spin_lock_irqsave(&mas->lock, flags);
-	reinit_completion(&mas->xfer_done);
-	geni_se_abort_m_cmd(se);
-	spin_unlock_irqrestore(&mas->lock, flags);
-	time_left = wait_for_completion_timeout(&mas->xfer_done, HZ);
-	if (!time_left)
-		dev_err(mas->dev, "Failed to cancel/abort m_cmd\n");
-}
-
 static int spi_geni_transfer_one(struct spi_master *spi,
 				struct spi_device *slv,
 				struct spi_transfer *xfer)
diff --git a/drivers/spi/spi-gpio.c b/drivers/spi/spi-gpio.c
index a4aee26028cd..3e98c1a0ba6d 100644
--- a/drivers/spi/spi-gpio.c
+++ b/drivers/spi/spi-gpio.c
@@ -428,7 +428,8 @@ static int spi_gpio_probe(struct platform_device *pdev)
 		return status;
 
 	master->bits_per_word_mask = SPI_BPW_RANGE_MASK(1, 32);
-	master->mode_bits = SPI_3WIRE | SPI_3WIRE_HIZ | SPI_CPHA | SPI_CPOL;
+	master->mode_bits = SPI_3WIRE | SPI_3WIRE_HIZ | SPI_CPHA | SPI_CPOL |
+			    SPI_CS_HIGH;
 	master->flags = master_flags;
 	master->bus_num = pdev->id;
 	/* The master needs to think there is a chipselect even if not connected */
diff --git a/drivers/spi/spi-mem.c b/drivers/spi/spi-mem.c
index 5217a5628be2..a4d8d19ecff9 100644
--- a/drivers/spi/spi-mem.c
+++ b/drivers/spi/spi-mem.c
@@ -537,7 +537,6 @@ EXPORT_SYMBOL_GPL(spi_mem_dirmap_create);
 /**
  * spi_mem_dirmap_destroy() - Destroy a direct mapping descriptor
  * @desc: the direct mapping descriptor to destroy
- * @info: direct mapping information
  *
  * This function destroys a direct mapping descriptor previously created by
  * spi_mem_dirmap_create().
@@ -548,9 +547,80 @@ void spi_mem_dirmap_destroy(struct spi_mem_dirmap_desc *desc)
 
 	if (!desc->nodirmap && ctlr->mem_ops && ctlr->mem_ops->dirmap_destroy)
 		ctlr->mem_ops->dirmap_destroy(desc);
+
+	kfree(desc);
 }
 EXPORT_SYMBOL_GPL(spi_mem_dirmap_destroy);
 
+static void devm_spi_mem_dirmap_release(struct device *dev, void *res)
+{
+	struct spi_mem_dirmap_desc *desc = *(struct spi_mem_dirmap_desc **)res;
+
+	spi_mem_dirmap_destroy(desc);
+}
+
+/**
+ * devm_spi_mem_dirmap_create() - Create a direct mapping descriptor and attach
+ *				  it to a device
+ * @dev: device the dirmap desc will be attached to
+ * @mem: SPI mem device this direct mapping should be created for
+ * @info: direct mapping information
+ *
+ * devm_ variant of the spi_mem_dirmap_create() function. See
+ * spi_mem_dirmap_create() for more details.
+ *
+ * Return: a valid pointer in case of success, and ERR_PTR() otherwise.
+ */
+struct spi_mem_dirmap_desc *
+devm_spi_mem_dirmap_create(struct device *dev, struct spi_mem *mem,
+			   const struct spi_mem_dirmap_info *info)
+{
+	struct spi_mem_dirmap_desc **ptr, *desc;
+
+	ptr = devres_alloc(devm_spi_mem_dirmap_release, sizeof(*ptr),
+			   GFP_KERNEL);
+	if (!ptr)
+		return ERR_PTR(-ENOMEM);
+
+	desc = spi_mem_dirmap_create(mem, info);
+	if (IS_ERR(desc)) {
+		devres_free(ptr);
+	} else {
+		*ptr = desc;
+		devres_add(dev, ptr);
+	}
+
+	return desc;
+}
+EXPORT_SYMBOL_GPL(devm_spi_mem_dirmap_create);
+
+static int devm_spi_mem_dirmap_match(struct device *dev, void *res, void *data)
+{
+        struct spi_mem_dirmap_desc **ptr = res;
+
+        if (WARN_ON(!ptr || !*ptr))
+                return 0;
+
+	return *ptr == data;
+}
+
+/**
+ * devm_spi_mem_dirmap_destroy() - Destroy a direct mapping descriptor attached
+ *				   to a device
+ * @dev: device the dirmap desc is attached to
+ * @desc: the direct mapping descriptor to destroy
+ *
+ * devm_ variant of the spi_mem_dirmap_destroy() function. See
+ * spi_mem_dirmap_destroy() for more details.
+ */
+void devm_spi_mem_dirmap_destroy(struct device *dev,
+				 struct spi_mem_dirmap_desc *desc)
+{
+	devres_release(dev, devm_spi_mem_dirmap_release,
+		       devm_spi_mem_dirmap_match, desc);
+}
+EXPORT_SYMBOL_GPL(devm_spi_mem_dirmap_destroy);
+
 /**
  * spi_mem_dirmap_dirmap_read() - Read data through a direct mapping
  * @desc: direct mapping descriptor
diff --git a/drivers/spi/spi-mxs.c b/drivers/spi/spi-mxs.c
index 6ac95a2a21ce..7bf53cfc25d6 100644
--- a/drivers/spi/spi-mxs.c
+++ b/drivers/spi/spi-mxs.c
@@ -39,6 +39,7 @@
 #include <linux/stmp_device.h>
 #include <linux/spi/spi.h>
 #include <linux/spi/mxs-spi.h>
+#include <trace/events/spi.h>
 
 #define DRIVER_NAME		"mxs-spi"
 
@@ -374,6 +375,8 @@ static int mxs_spi_transfer_one(struct spi_master *master,
 
 	list_for_each_entry(t, &m->transfers, transfer_list) {
 
+		trace_spi_transfer_start(m, t);
+
 		status = mxs_spi_setup_transfer(m->spi, t);
 		if (status)
 			break;
@@ -419,6 +422,8 @@ static int mxs_spi_transfer_one(struct spi_master *master,
 						flag);
 		}
 
+		trace_spi_transfer_stop(m, t);
+
 		if (status) {
 			stmp_reset_block(ssp->base);
 			break;
diff --git a/drivers/spi/spi-npcm-pspi.c b/drivers/spi/spi-npcm-pspi.c
index e1dca79b9090..734a2b956959 100644
--- a/drivers/spi/spi-npcm-pspi.c
+++ b/drivers/spi/spi-npcm-pspi.c
@@ -465,7 +465,8 @@ static int npcm_pspi_probe(struct platform_device *pdev)
 
 static int npcm_pspi_remove(struct platform_device *pdev)
 {
-	struct npcm_pspi *priv = platform_get_drvdata(pdev);
+	struct spi_master *master = platform_get_drvdata(pdev);
+	struct npcm_pspi *priv = spi_master_get_devdata(master);
 
 	npcm_pspi_reset_hw(priv);
 	clk_disable_unprepare(priv->clk);
diff --git a/drivers/spi/spi-nxp-fspi.c b/drivers/spi/spi-nxp-fspi.c
new file mode 100644
index 000000000000..8894f98cc99c
--- /dev/null
+++ b/drivers/spi/spi-nxp-fspi.c
@@ -0,0 +1,1106 @@
+// SPDX-License-Identifier: GPL-2.0+
+
+/*
+ * NXP FlexSPI(FSPI) controller driver.
+ *
+ * Copyright 2019 NXP.
+ *
+ * FlexSPI is a flexsible SPI host controller which supports two SPI
+ * channels and up to 4 external devices. Each channel supports
+ * Single/Dual/Quad/Octal mode data transfer (1/2/4/8 bidirectional
+ * data lines).
+ *
+ * FlexSPI controller is driven by the LUT(Look-up Table) registers
+ * LUT registers are a look-up-table for sequences of instructions.
+ * A valid sequence consists of four LUT registers.
+ * Maximum 32 LUT sequences can be programmed simultaneously.
+ *
+ * LUTs are being created at run-time based on the commands passed
+ * from the spi-mem framework, thus using single LUT index.
+ *
+ * Software triggered Flash read/write access by IP Bus.
+ *
+ * Memory mapped read access by AHB Bus.
+ *
+ * Based on SPI MEM interface and spi-fsl-qspi.c driver.
+ *
+ * Author:
+ *     Yogesh Narayan Gaur <yogeshnarayan.gaur@nxp.com>
+ *     Boris Brezillon <bbrezillon@kernel.org>
+ *     Frieder Schrempf <frieder.schrempf@kontron.de>
+ */
+
+#include <linux/bitops.h>
+#include <linux/clk.h>
+#include <linux/completion.h>
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/errno.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/iopoll.h>
+#include <linux/jiffies.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <linux/pm_qos.h>
+#include <linux/sizes.h>
+
+#include <linux/spi/spi.h>
+#include <linux/spi/spi-mem.h>
+
+/*
+ * The driver only uses one single LUT entry, that is updated on
+ * each call of exec_op(). Index 0 is preset at boot with a basic
+ * read operation, so let's use the last entry (31).
+ */
+#define	SEQID_LUT			31
+
+/* Registers used by the driver */
+#define FSPI_MCR0			0x00
+#define FSPI_MCR0_AHB_TIMEOUT(x)	((x) << 24)
+#define FSPI_MCR0_IP_TIMEOUT(x)		((x) << 16)
+#define FSPI_MCR0_LEARN_EN		BIT(15)
+#define FSPI_MCR0_SCRFRUN_EN		BIT(14)
+#define FSPI_MCR0_OCTCOMB_EN		BIT(13)
+#define FSPI_MCR0_DOZE_EN		BIT(12)
+#define FSPI_MCR0_HSEN			BIT(11)
+#define FSPI_MCR0_SERCLKDIV		BIT(8)
+#define FSPI_MCR0_ATDF_EN		BIT(7)
+#define FSPI_MCR0_ARDF_EN		BIT(6)
+#define FSPI_MCR0_RXCLKSRC(x)		((x) << 4)
+#define FSPI_MCR0_END_CFG(x)		((x) << 2)
+#define FSPI_MCR0_MDIS			BIT(1)
+#define FSPI_MCR0_SWRST			BIT(0)
+
+#define FSPI_MCR1			0x04
+#define FSPI_MCR1_SEQ_TIMEOUT(x)	((x) << 16)
+#define FSPI_MCR1_AHB_TIMEOUT(x)	(x)
+
+#define FSPI_MCR2			0x08
+#define FSPI_MCR2_IDLE_WAIT(x)		((x) << 24)
+#define FSPI_MCR2_SAMEDEVICEEN		BIT(15)
+#define FSPI_MCR2_CLRLRPHS		BIT(14)
+#define FSPI_MCR2_ABRDATSZ		BIT(8)
+#define FSPI_MCR2_ABRLEARN		BIT(7)
+#define FSPI_MCR2_ABR_READ		BIT(6)
+#define FSPI_MCR2_ABRWRITE		BIT(5)
+#define FSPI_MCR2_ABRDUMMY		BIT(4)
+#define FSPI_MCR2_ABR_MODE		BIT(3)
+#define FSPI_MCR2_ABRCADDR		BIT(2)
+#define FSPI_MCR2_ABRRADDR		BIT(1)
+#define FSPI_MCR2_ABR_CMD		BIT(0)
+
+#define FSPI_AHBCR			0x0c
+#define FSPI_AHBCR_RDADDROPT		BIT(6)
+#define FSPI_AHBCR_PREF_EN		BIT(5)
+#define FSPI_AHBCR_BUFF_EN		BIT(4)
+#define FSPI_AHBCR_CACH_EN		BIT(3)
+#define FSPI_AHBCR_CLRTXBUF		BIT(2)
+#define FSPI_AHBCR_CLRRXBUF		BIT(1)
+#define FSPI_AHBCR_PAR_EN		BIT(0)
+
+#define FSPI_INTEN			0x10
+#define FSPI_INTEN_SCLKSBWR		BIT(9)
+#define FSPI_INTEN_SCLKSBRD		BIT(8)
+#define FSPI_INTEN_DATALRNFL		BIT(7)
+#define FSPI_INTEN_IPTXWE		BIT(6)
+#define FSPI_INTEN_IPRXWA		BIT(5)
+#define FSPI_INTEN_AHBCMDERR		BIT(4)
+#define FSPI_INTEN_IPCMDERR		BIT(3)
+#define FSPI_INTEN_AHBCMDGE		BIT(2)
+#define FSPI_INTEN_IPCMDGE		BIT(1)
+#define FSPI_INTEN_IPCMDDONE		BIT(0)
+
+#define FSPI_INTR			0x14
+#define FSPI_INTR_SCLKSBWR		BIT(9)
+#define FSPI_INTR_SCLKSBRD		BIT(8)
+#define FSPI_INTR_DATALRNFL		BIT(7)
+#define FSPI_INTR_IPTXWE		BIT(6)
+#define FSPI_INTR_IPRXWA		BIT(5)
+#define FSPI_INTR_AHBCMDERR		BIT(4)
+#define FSPI_INTR_IPCMDERR		BIT(3)
+#define FSPI_INTR_AHBCMDGE		BIT(2)
+#define FSPI_INTR_IPCMDGE		BIT(1)
+#define FSPI_INTR_IPCMDDONE		BIT(0)
+
+#define FSPI_LUTKEY			0x18
+#define FSPI_LUTKEY_VALUE		0x5AF05AF0
+
+#define FSPI_LCKCR			0x1C
+
+#define FSPI_LCKER_LOCK			0x1
+#define FSPI_LCKER_UNLOCK		0x2
+
+#define FSPI_BUFXCR_INVALID_MSTRID	0xE
+#define FSPI_AHBRX_BUF0CR0		0x20
+#define FSPI_AHBRX_BUF1CR0		0x24
+#define FSPI_AHBRX_BUF2CR0		0x28
+#define FSPI_AHBRX_BUF3CR0		0x2C
+#define FSPI_AHBRX_BUF4CR0		0x30
+#define FSPI_AHBRX_BUF5CR0		0x34
+#define FSPI_AHBRX_BUF6CR0		0x38
+#define FSPI_AHBRX_BUF7CR0		0x3C
+#define FSPI_AHBRXBUF0CR7_PREF		BIT(31)
+
+#define FSPI_AHBRX_BUF0CR1		0x40
+#define FSPI_AHBRX_BUF1CR1		0x44
+#define FSPI_AHBRX_BUF2CR1		0x48
+#define FSPI_AHBRX_BUF3CR1		0x4C
+#define FSPI_AHBRX_BUF4CR1		0x50
+#define FSPI_AHBRX_BUF5CR1		0x54
+#define FSPI_AHBRX_BUF6CR1		0x58
+#define FSPI_AHBRX_BUF7CR1		0x5C
+
+#define FSPI_FLSHA1CR0			0x60
+#define FSPI_FLSHA2CR0			0x64
+#define FSPI_FLSHB1CR0			0x68
+#define FSPI_FLSHB2CR0			0x6C
+#define FSPI_FLSHXCR0_SZ_KB		10
+#define FSPI_FLSHXCR0_SZ(x)		((x) >> FSPI_FLSHXCR0_SZ_KB)
+
+#define FSPI_FLSHA1CR1			0x70
+#define FSPI_FLSHA2CR1			0x74
+#define FSPI_FLSHB1CR1			0x78
+#define FSPI_FLSHB2CR1			0x7C
+#define FSPI_FLSHXCR1_CSINTR(x)		((x) << 16)
+#define FSPI_FLSHXCR1_CAS(x)		((x) << 11)
+#define FSPI_FLSHXCR1_WA		BIT(10)
+#define FSPI_FLSHXCR1_TCSH(x)		((x) << 5)
+#define FSPI_FLSHXCR1_TCSS(x)		(x)
+
+#define FSPI_FLSHA1CR2			0x80
+#define FSPI_FLSHA2CR2			0x84
+#define FSPI_FLSHB1CR2			0x88
+#define FSPI_FLSHB2CR2			0x8C
+#define FSPI_FLSHXCR2_CLRINSP		BIT(24)
+#define FSPI_FLSHXCR2_AWRWAIT		BIT(16)
+#define FSPI_FLSHXCR2_AWRSEQN_SHIFT	13
+#define FSPI_FLSHXCR2_AWRSEQI_SHIFT	8
+#define FSPI_FLSHXCR2_ARDSEQN_SHIFT	5
+#define FSPI_FLSHXCR2_ARDSEQI_SHIFT	0
+
+#define FSPI_IPCR0			0xA0
+
+#define FSPI_IPCR1			0xA4
+#define FSPI_IPCR1_IPAREN		BIT(31)
+#define FSPI_IPCR1_SEQNUM_SHIFT		24
+#define FSPI_IPCR1_SEQID_SHIFT		16
+#define FSPI_IPCR1_IDATSZ(x)		(x)
+
+#define FSPI_IPCMD			0xB0
+#define FSPI_IPCMD_TRG			BIT(0)
+
+#define FSPI_DLPR			0xB4
+
+#define FSPI_IPRXFCR			0xB8
+#define FSPI_IPRXFCR_CLR		BIT(0)
+#define FSPI_IPRXFCR_DMA_EN		BIT(1)
+#define FSPI_IPRXFCR_WMRK(x)		((x) << 2)
+
+#define FSPI_IPTXFCR			0xBC
+#define FSPI_IPTXFCR_CLR		BIT(0)
+#define FSPI_IPTXFCR_DMA_EN		BIT(1)
+#define FSPI_IPTXFCR_WMRK(x)		((x) << 2)
+
+#define FSPI_DLLACR			0xC0
+#define FSPI_DLLACR_OVRDEN		BIT(8)
+
+#define FSPI_DLLBCR			0xC4
+#define FSPI_DLLBCR_OVRDEN		BIT(8)
+
+#define FSPI_STS0			0xE0
+#define FSPI_STS0_DLPHB(x)		((x) << 8)
+#define FSPI_STS0_DLPHA(x)		((x) << 4)
+#define FSPI_STS0_CMD_SRC(x)		((x) << 2)
+#define FSPI_STS0_ARB_IDLE		BIT(1)
+#define FSPI_STS0_SEQ_IDLE		BIT(0)
+
+#define FSPI_STS1			0xE4
+#define FSPI_STS1_IP_ERRCD(x)		((x) << 24)
+#define FSPI_STS1_IP_ERRID(x)		((x) << 16)
+#define FSPI_STS1_AHB_ERRCD(x)		((x) << 8)
+#define FSPI_STS1_AHB_ERRID(x)		(x)
+
+#define FSPI_AHBSPNST			0xEC
+#define FSPI_AHBSPNST_DATLFT(x)		((x) << 16)
+#define FSPI_AHBSPNST_BUFID(x)		((x) << 1)
+#define FSPI_AHBSPNST_ACTIVE		BIT(0)
+
+#define FSPI_IPRXFSTS			0xF0
+#define FSPI_IPRXFSTS_RDCNTR(x)		((x) << 16)
+#define FSPI_IPRXFSTS_FILL(x)		(x)
+
+#define FSPI_IPTXFSTS			0xF4
+#define FSPI_IPTXFSTS_WRCNTR(x)		((x) << 16)
+#define FSPI_IPTXFSTS_FILL(x)		(x)
+
+#define FSPI_RFDR			0x100
+#define FSPI_TFDR			0x180
+
+#define FSPI_LUT_BASE			0x200
+#define FSPI_LUT_OFFSET			(SEQID_LUT * 4 * 4)
+#define FSPI_LUT_REG(idx) \
+	(FSPI_LUT_BASE + FSPI_LUT_OFFSET + (idx) * 4)
+
+/* register map end */
+
+/* Instruction set for the LUT register. */
+#define LUT_STOP			0x00
+#define LUT_CMD				0x01
+#define LUT_ADDR			0x02
+#define LUT_CADDR_SDR			0x03
+#define LUT_MODE			0x04
+#define LUT_MODE2			0x05
+#define LUT_MODE4			0x06
+#define LUT_MODE8			0x07
+#define LUT_NXP_WRITE			0x08
+#define LUT_NXP_READ			0x09
+#define LUT_LEARN_SDR			0x0A
+#define LUT_DATSZ_SDR			0x0B
+#define LUT_DUMMY			0x0C
+#define LUT_DUMMY_RWDS_SDR		0x0D
+#define LUT_JMP_ON_CS			0x1F
+#define LUT_CMD_DDR			0x21
+#define LUT_ADDR_DDR			0x22
+#define LUT_CADDR_DDR			0x23
+#define LUT_MODE_DDR			0x24
+#define LUT_MODE2_DDR			0x25
+#define LUT_MODE4_DDR			0x26
+#define LUT_MODE8_DDR			0x27
+#define LUT_WRITE_DDR			0x28
+#define LUT_READ_DDR			0x29
+#define LUT_LEARN_DDR			0x2A
+#define LUT_DATSZ_DDR			0x2B
+#define LUT_DUMMY_DDR			0x2C
+#define LUT_DUMMY_RWDS_DDR		0x2D
+
+/*
+ * Calculate number of required PAD bits for LUT register.
+ *
+ * The pad stands for the number of IO lines [0:7].
+ * For example, the octal read needs eight IO lines,
+ * so you should use LUT_PAD(8). This macro
+ * returns 3 i.e. use eight (2^3) IP lines for read.
+ */
+#define LUT_PAD(x) (fls(x) - 1)
+
+/*
+ * Macro for constructing the LUT entries with the following
+ * register layout:
+ *
+ *  ---------------------------------------------------
+ *  | INSTR1 | PAD1 | OPRND1 | INSTR0 | PAD0 | OPRND0 |
+ *  ---------------------------------------------------
+ */
+#define PAD_SHIFT		8
+#define INSTR_SHIFT		10
+#define OPRND_SHIFT		16
+
+/* Macros for constructing the LUT register. */
+#define LUT_DEF(idx, ins, pad, opr)			  \
+	((((ins) << INSTR_SHIFT) | ((pad) << PAD_SHIFT) | \
+	(opr)) << (((idx) % 2) * OPRND_SHIFT))
+
+#define POLL_TOUT		5000
+#define NXP_FSPI_MAX_CHIPSELECT		4
+
+struct nxp_fspi_devtype_data {
+	unsigned int rxfifo;
+	unsigned int txfifo;
+	unsigned int ahb_buf_size;
+	unsigned int quirks;
+	bool little_endian;
+};
+
+static const struct nxp_fspi_devtype_data lx2160a_data = {
+	.rxfifo = SZ_512,       /* (64  * 64 bits)  */
+	.txfifo = SZ_1K,        /* (128 * 64 bits)  */
+	.ahb_buf_size = SZ_2K,  /* (256 * 64 bits)  */
+	.quirks = 0,
+	.little_endian = true,  /* little-endian    */
+};
+
+struct nxp_fspi {
+	void __iomem *iobase;
+	void __iomem *ahb_addr;
+	u32 memmap_phy;
+	u32 memmap_phy_size;
+	struct clk *clk, *clk_en;
+	struct device *dev;
+	struct completion c;
+	const struct nxp_fspi_devtype_data *devtype_data;
+	struct mutex lock;
+	struct pm_qos_request pm_qos_req;
+	int selected;
+};
+
+/*
+ * R/W functions for big- or little-endian registers:
+ * The FSPI controller's endianness is independent of
+ * the CPU core's endianness. So far, although the CPU
+ * core is little-endian the FSPI controller can use
+ * big-endian or little-endian.
+ */
+static void fspi_writel(struct nxp_fspi *f, u32 val, void __iomem *addr)
+{
+	if (f->devtype_data->little_endian)
+		iowrite32(val, addr);
+	else
+		iowrite32be(val, addr);
+}
+
+static u32 fspi_readl(struct nxp_fspi *f, void __iomem *addr)
+{
+	if (f->devtype_data->little_endian)
+		return ioread32(addr);
+	else
+		return ioread32be(addr);
+}
+
+static irqreturn_t nxp_fspi_irq_handler(int irq, void *dev_id)
+{
+	struct nxp_fspi *f = dev_id;
+	u32 reg;
+
+	/* clear interrupt */
+	reg = fspi_readl(f, f->iobase + FSPI_INTR);
+	fspi_writel(f, FSPI_INTR_IPCMDDONE, f->iobase + FSPI_INTR);
+
+	if (reg & FSPI_INTR_IPCMDDONE)
+		complete(&f->c);
+
+	return IRQ_HANDLED;
+}
+
+static int nxp_fspi_check_buswidth(struct nxp_fspi *f, u8 width)
+{
+	switch (width) {
+	case 1:
+	case 2:
+	case 4:
+	case 8:
+		return 0;
+	}
+
+	return -ENOTSUPP;
+}
+
+static bool nxp_fspi_supports_op(struct spi_mem *mem,
+				 const struct spi_mem_op *op)
+{
+	struct nxp_fspi *f = spi_controller_get_devdata(mem->spi->master);
+	int ret;
+
+	ret = nxp_fspi_check_buswidth(f, op->cmd.buswidth);
+
+	if (op->addr.nbytes)
+		ret |= nxp_fspi_check_buswidth(f, op->addr.buswidth);
+
+	if (op->dummy.nbytes)
+		ret |= nxp_fspi_check_buswidth(f, op->dummy.buswidth);
+
+	if (op->data.nbytes)
+		ret |= nxp_fspi_check_buswidth(f, op->data.buswidth);
+
+	if (ret)
+		return false;
+
+	/*
+	 * The number of address bytes should be equal to or less than 4 bytes.
+	 */
+	if (op->addr.nbytes > 4)
+		return false;
+
+	/*
+	 * If requested address value is greater than controller assigned
+	 * memory mapped space, return error as it didn't fit in the range
+	 * of assigned address space.
+	 */
+	if (op->addr.val >= f->memmap_phy_size)
+		return false;
+
+	/* Max 64 dummy clock cycles supported */
+	if (op->dummy.buswidth &&
+	    (op->dummy.nbytes * 8 / op->dummy.buswidth > 64))
+		return false;
+
+	/* Max data length, check controller limits and alignment */
+	if (op->data.dir == SPI_MEM_DATA_IN &&
+	    (op->data.nbytes > f->devtype_data->ahb_buf_size ||
+	     (op->data.nbytes > f->devtype_data->rxfifo - 4 &&
+	      !IS_ALIGNED(op->data.nbytes, 8))))
+		return false;
+
+	if (op->data.dir == SPI_MEM_DATA_OUT &&
+	    op->data.nbytes > f->devtype_data->txfifo)
+		return false;
+
+	return true;
+}
+
+/* Instead of busy looping invoke readl_poll_timeout functionality. */
+static int fspi_readl_poll_tout(struct nxp_fspi *f, void __iomem *base,
+				u32 mask, u32 delay_us,
+				u32 timeout_us, bool c)
+{
+	u32 reg;
+
+	if (!f->devtype_data->little_endian)
+		mask = (u32)cpu_to_be32(mask);
+
+	if (c)
+		return readl_poll_timeout(base, reg, (reg & mask),
+					  delay_us, timeout_us);
+	else
+		return readl_poll_timeout(base, reg, !(reg & mask),
+					  delay_us, timeout_us);
+}
+
+/*
+ * If the slave device content being changed by Write/Erase, need to
+ * invalidate the AHB buffer. This can be achieved by doing the reset
+ * of controller after setting MCR0[SWRESET] bit.
+ */
+static inline void nxp_fspi_invalid(struct nxp_fspi *f)
+{
+	u32 reg;
+	int ret;
+
+	reg = fspi_readl(f, f->iobase + FSPI_MCR0);
+	fspi_writel(f, reg | FSPI_MCR0_SWRST, f->iobase + FSPI_MCR0);
+
+	/* w1c register, wait unit clear */
+	ret = fspi_readl_poll_tout(f, f->iobase + FSPI_MCR0,
+				   FSPI_MCR0_SWRST, 0, POLL_TOUT, false);
+	WARN_ON(ret);
+}
+
+static void nxp_fspi_prepare_lut(struct nxp_fspi *f,
+				 const struct spi_mem_op *op)
+{
+	void __iomem *base = f->iobase;
+	u32 lutval[4] = {};
+	int lutidx = 1, i;
+
+	/* cmd */
+	lutval[0] |= LUT_DEF(0, LUT_CMD, LUT_PAD(op->cmd.buswidth),
+			     op->cmd.opcode);
+
+	/* addr bytes */
+	if (op->addr.nbytes) {
+		lutval[lutidx / 2] |= LUT_DEF(lutidx, LUT_ADDR,
+					      LUT_PAD(op->addr.buswidth),
+					      op->addr.nbytes * 8);
+		lutidx++;
+	}
+
+	/* dummy bytes, if needed */
+	if (op->dummy.nbytes) {
+		lutval[lutidx / 2] |= LUT_DEF(lutidx, LUT_DUMMY,
+		/*
+		 * Due to FlexSPI controller limitation number of PAD for dummy
+		 * buswidth needs to be programmed as equal to data buswidth.
+		 */
+					      LUT_PAD(op->data.buswidth),
+					      op->dummy.nbytes * 8 /
+					      op->dummy.buswidth);
+		lutidx++;
+	}
+
+	/* read/write data bytes */
+	if (op->data.nbytes) {
+		lutval[lutidx / 2] |= LUT_DEF(lutidx,
+					      op->data.dir == SPI_MEM_DATA_IN ?
+					      LUT_NXP_READ : LUT_NXP_WRITE,
+					      LUT_PAD(op->data.buswidth),
+					      0);
+		lutidx++;
+	}
+
+	/* stop condition. */
+	lutval[lutidx / 2] |= LUT_DEF(lutidx, LUT_STOP, 0, 0);
+
+	/* unlock LUT */
+	fspi_writel(f, FSPI_LUTKEY_VALUE, f->iobase + FSPI_LUTKEY);
+	fspi_writel(f, FSPI_LCKER_UNLOCK, f->iobase + FSPI_LCKCR);
+
+	/* fill LUT */
+	for (i = 0; i < ARRAY_SIZE(lutval); i++)
+		fspi_writel(f, lutval[i], base + FSPI_LUT_REG(i));
+
+	dev_dbg(f->dev, "CMD[%x] lutval[0:%x \t 1:%x \t 2:%x \t 3:%x]\n",
+		op->cmd.opcode, lutval[0], lutval[1], lutval[2], lutval[3]);
+
+	/* lock LUT */
+	fspi_writel(f, FSPI_LUTKEY_VALUE, f->iobase + FSPI_LUTKEY);
+	fspi_writel(f, FSPI_LCKER_LOCK, f->iobase + FSPI_LCKCR);
+}
+
+static int nxp_fspi_clk_prep_enable(struct nxp_fspi *f)
+{
+	int ret;
+
+	ret = clk_prepare_enable(f->clk_en);
+	if (ret)
+		return ret;
+
+	ret = clk_prepare_enable(f->clk);
+	if (ret) {
+		clk_disable_unprepare(f->clk_en);
+		return ret;
+	}
+
+	return 0;
+}
+
+static void nxp_fspi_clk_disable_unprep(struct nxp_fspi *f)
+{
+	clk_disable_unprepare(f->clk);
+	clk_disable_unprepare(f->clk_en);
+}
+
+/*
+ * In FlexSPI controller, flash access is based on value of FSPI_FLSHXXCR0
+ * register and start base address of the slave device.
+ *
+ *							    (Higher address)
+ *				--------    <-- FLSHB2CR0
+ *				|  B2  |
+ *				|      |
+ *	B2 start address -->	--------    <-- FLSHB1CR0
+ *				|  B1  |
+ *				|      |
+ *	B1 start address -->	--------    <-- FLSHA2CR0
+ *				|  A2  |
+ *				|      |
+ *	A2 start address -->	--------    <-- FLSHA1CR0
+ *				|  A1  |
+ *				|      |
+ *	A1 start address -->	--------		    (Lower address)
+ *
+ *
+ * Start base address defines the starting address range for given CS and
+ * FSPI_FLSHXXCR0 defines the size of the slave device connected at given CS.
+ *
+ * But, different targets are having different combinations of number of CS,
+ * some targets only have single CS or two CS covering controller's full
+ * memory mapped space area.
+ * Thus, implementation is being done as independent of the size and number
+ * of the connected slave device.
+ * Assign controller memory mapped space size as the size to the connected
+ * slave device.
+ * Mark FLSHxxCR0 as zero initially and then assign value only to the selected
+ * chip-select Flash configuration register.
+ *
+ * For e.g. to access CS2 (B1), FLSHB1CR0 register would be equal to the
+ * memory mapped size of the controller.
+ * Value for rest of the CS FLSHxxCR0 register would be zero.
+ *
+ */
+static void nxp_fspi_select_mem(struct nxp_fspi *f, struct spi_device *spi)
+{
+	unsigned long rate = spi->max_speed_hz;
+	int ret;
+	uint64_t size_kb;
+
+	/*
+	 * Return, if previously selected slave device is same as current
+	 * requested slave device.
+	 */
+	if (f->selected == spi->chip_select)
+		return;
+
+	/* Reset FLSHxxCR0 registers */
+	fspi_writel(f, 0, f->iobase + FSPI_FLSHA1CR0);
+	fspi_writel(f, 0, f->iobase + FSPI_FLSHA2CR0);
+	fspi_writel(f, 0, f->iobase + FSPI_FLSHB1CR0);
+	fspi_writel(f, 0, f->iobase + FSPI_FLSHB2CR0);
+
+	/* Assign controller memory mapped space as size, KBytes, of flash. */
+	size_kb = FSPI_FLSHXCR0_SZ(f->memmap_phy_size);
+
+	fspi_writel(f, size_kb, f->iobase + FSPI_FLSHA1CR0 +
+		    4 * spi->chip_select);
+
+	dev_dbg(f->dev, "Slave device [CS:%x] selected\n", spi->chip_select);
+
+	nxp_fspi_clk_disable_unprep(f);
+
+	ret = clk_set_rate(f->clk, rate);
+	if (ret)
+		return;
+
+	ret = nxp_fspi_clk_prep_enable(f);
+	if (ret)
+		return;
+
+	f->selected = spi->chip_select;
+}
+
+static void nxp_fspi_read_ahb(struct nxp_fspi *f, const struct spi_mem_op *op)
+{
+	u32 len = op->data.nbytes;
+
+	/* Read out the data directly from the AHB buffer. */
+	memcpy_fromio(op->data.buf.in, (f->ahb_addr + op->addr.val), len);
+}
+
+static void nxp_fspi_fill_txfifo(struct nxp_fspi *f,
+				 const struct spi_mem_op *op)
+{
+	void __iomem *base = f->iobase;
+	int i, ret;
+	u8 *buf = (u8 *) op->data.buf.out;
+
+	/* clear the TX FIFO. */
+	fspi_writel(f, FSPI_IPTXFCR_CLR, base + FSPI_IPTXFCR);
+
+	/*
+	 * Default value of water mark level is 8 bytes, hence in single
+	 * write request controller can write max 8 bytes of data.
+	 */
+
+	for (i = 0; i < ALIGN_DOWN(op->data.nbytes, 8); i += 8) {
+		/* Wait for TXFIFO empty */
+		ret = fspi_readl_poll_tout(f, f->iobase + FSPI_INTR,
+					   FSPI_INTR_IPTXWE, 0,
+					   POLL_TOUT, true);
+		WARN_ON(ret);
+
+		fspi_writel(f, *(u32 *) (buf + i), base + FSPI_TFDR);
+		fspi_writel(f, *(u32 *) (buf + i + 4), base + FSPI_TFDR + 4);
+		fspi_writel(f, FSPI_INTR_IPTXWE, base + FSPI_INTR);
+	}
+
+	if (i < op->data.nbytes) {
+		u32 data = 0;
+		int j;
+		/* Wait for TXFIFO empty */
+		ret = fspi_readl_poll_tout(f, f->iobase + FSPI_INTR,
+					   FSPI_INTR_IPTXWE, 0,
+					   POLL_TOUT, true);
+		WARN_ON(ret);
+
+		for (j = 0; j < ALIGN(op->data.nbytes - i, 4); j += 4) {
+			memcpy(&data, buf + i + j, 4);
+			fspi_writel(f, data, base + FSPI_TFDR + j);
+		}
+		fspi_writel(f, FSPI_INTR_IPTXWE, base + FSPI_INTR);
+	}
+}
+
+static void nxp_fspi_read_rxfifo(struct nxp_fspi *f,
+			  const struct spi_mem_op *op)
+{
+	void __iomem *base = f->iobase;
+	int i, ret;
+	int len = op->data.nbytes;
+	u8 *buf = (u8 *) op->data.buf.in;
+
+	/*
+	 * Default value of water mark level is 8 bytes, hence in single
+	 * read request controller can read max 8 bytes of data.
+	 */
+	for (i = 0; i < ALIGN_DOWN(len, 8); i += 8) {
+		/* Wait for RXFIFO available */
+		ret = fspi_readl_poll_tout(f, f->iobase + FSPI_INTR,
+					   FSPI_INTR_IPRXWA, 0,
+					   POLL_TOUT, true);
+		WARN_ON(ret);
+
+		*(u32 *)(buf + i) = fspi_readl(f, base + FSPI_RFDR);
+		*(u32 *)(buf + i + 4) = fspi_readl(f, base + FSPI_RFDR + 4);
+		/* move the FIFO pointer */
+		fspi_writel(f, FSPI_INTR_IPRXWA, base + FSPI_INTR);
+	}
+
+	if (i < len) {
+		u32 tmp;
+		int size, j;
+
+		buf = op->data.buf.in + i;
+		/* Wait for RXFIFO available */
+		ret = fspi_readl_poll_tout(f, f->iobase + FSPI_INTR,
+					   FSPI_INTR_IPRXWA, 0,
+					   POLL_TOUT, true);
+		WARN_ON(ret);
+
+		len = op->data.nbytes - i;
+		for (j = 0; j < op->data.nbytes - i; j += 4) {
+			tmp = fspi_readl(f, base + FSPI_RFDR + j);
+			size = min(len, 4);
+			memcpy(buf + j, &tmp, size);
+			len -= size;
+		}
+	}
+
+	/* invalid the RXFIFO */
+	fspi_writel(f, FSPI_IPRXFCR_CLR, base + FSPI_IPRXFCR);
+	/* move the FIFO pointer */
+	fspi_writel(f, FSPI_INTR_IPRXWA, base + FSPI_INTR);
+}
+
+static int nxp_fspi_do_op(struct nxp_fspi *f, const struct spi_mem_op *op)
+{
+	void __iomem *base = f->iobase;
+	int seqnum = 0;
+	int err = 0;
+	u32 reg;
+
+	reg = fspi_readl(f, base + FSPI_IPRXFCR);
+	/* invalid RXFIFO first */
+	reg &= ~FSPI_IPRXFCR_DMA_EN;
+	reg = reg | FSPI_IPRXFCR_CLR;
+	fspi_writel(f, reg, base + FSPI_IPRXFCR);
+
+	init_completion(&f->c);
+
+	fspi_writel(f, op->addr.val, base + FSPI_IPCR0);
+	/*
+	 * Always start the sequence at the same index since we update
+	 * the LUT at each exec_op() call. And also specify the DATA
+	 * length, since it's has not been specified in the LUT.
+	 */
+	fspi_writel(f, op->data.nbytes |
+		 (SEQID_LUT << FSPI_IPCR1_SEQID_SHIFT) |
+		 (seqnum << FSPI_IPCR1_SEQNUM_SHIFT),
+		 base + FSPI_IPCR1);
+
+	/* Trigger the LUT now. */
+	fspi_writel(f, FSPI_IPCMD_TRG, base + FSPI_IPCMD);
+
+	/* Wait for the interrupt. */
+	if (!wait_for_completion_timeout(&f->c, msecs_to_jiffies(1000)))
+		err = -ETIMEDOUT;
+
+	/* Invoke IP data read, if request is of data read. */
+	if (!err && op->data.nbytes && op->data.dir == SPI_MEM_DATA_IN)
+		nxp_fspi_read_rxfifo(f, op);
+
+	return err;
+}
+
+static int nxp_fspi_exec_op(struct spi_mem *mem, const struct spi_mem_op *op)
+{
+	struct nxp_fspi *f = spi_controller_get_devdata(mem->spi->master);
+	int err = 0;
+
+	mutex_lock(&f->lock);
+
+	/* Wait for controller being ready. */
+	err = fspi_readl_poll_tout(f, f->iobase + FSPI_STS0,
+				   FSPI_STS0_ARB_IDLE, 1, POLL_TOUT, true);
+	WARN_ON(err);
+
+	nxp_fspi_select_mem(f, mem->spi);
+
+	nxp_fspi_prepare_lut(f, op);
+	/*
+	 * If we have large chunks of data, we read them through the AHB bus
+	 * by accessing the mapped memory. In all other cases we use
+	 * IP commands to access the flash.
+	 */
+	if (op->data.nbytes > (f->devtype_data->rxfifo - 4) &&
+	    op->data.dir == SPI_MEM_DATA_IN) {
+		nxp_fspi_read_ahb(f, op);
+	} else {
+		if (op->data.nbytes && op->data.dir == SPI_MEM_DATA_OUT)
+			nxp_fspi_fill_txfifo(f, op);
+
+		err = nxp_fspi_do_op(f, op);
+	}
+
+	/* Invalidate the data in the AHB buffer. */
+	nxp_fspi_invalid(f);
+
+	mutex_unlock(&f->lock);
+
+	return err;
+}
+
+static int nxp_fspi_adjust_op_size(struct spi_mem *mem, struct spi_mem_op *op)
+{
+	struct nxp_fspi *f = spi_controller_get_devdata(mem->spi->master);
+
+	if (op->data.dir == SPI_MEM_DATA_OUT) {
+		if (op->data.nbytes > f->devtype_data->txfifo)
+			op->data.nbytes = f->devtype_data->txfifo;
+	} else {
+		if (op->data.nbytes > f->devtype_data->ahb_buf_size)
+			op->data.nbytes = f->devtype_data->ahb_buf_size;
+		else if (op->data.nbytes > (f->devtype_data->rxfifo - 4))
+			op->data.nbytes = ALIGN_DOWN(op->data.nbytes, 8);
+	}
+
+	return 0;
+}
+
+static int nxp_fspi_default_setup(struct nxp_fspi *f)
+{
+	void __iomem *base = f->iobase;
+	int ret, i;
+	u32 reg;
+
+	/* disable and unprepare clock to avoid glitch pass to controller */
+	nxp_fspi_clk_disable_unprep(f);
+
+	/* the default frequency, we will change it later if necessary. */
+	ret = clk_set_rate(f->clk, 20000000);
+	if (ret)
+		return ret;
+
+	ret = nxp_fspi_clk_prep_enable(f);
+	if (ret)
+		return ret;
+
+	/* Reset the module */
+	/* w1c register, wait unit clear */
+	ret = fspi_readl_poll_tout(f, f->iobase + FSPI_MCR0,
+				   FSPI_MCR0_SWRST, 0, POLL_TOUT, false);
+	WARN_ON(ret);
+
+	/* Disable the module */
+	fspi_writel(f, FSPI_MCR0_MDIS, base + FSPI_MCR0);
+
+	/* Reset the DLL register to default value */
+	fspi_writel(f, FSPI_DLLACR_OVRDEN, base + FSPI_DLLACR);
+	fspi_writel(f, FSPI_DLLBCR_OVRDEN, base + FSPI_DLLBCR);
+
+	/* enable module */
+	fspi_writel(f, FSPI_MCR0_AHB_TIMEOUT(0xFF) | FSPI_MCR0_IP_TIMEOUT(0xFF),
+		 base + FSPI_MCR0);
+
+	/*
+	 * Disable same device enable bit and configure all slave devices
+	 * independently.
+	 */
+	reg = fspi_readl(f, f->iobase + FSPI_MCR2);
+	reg = reg & ~(FSPI_MCR2_SAMEDEVICEEN);
+	fspi_writel(f, reg, base + FSPI_MCR2);
+
+	/* AHB configuration for access buffer 0~7. */
+	for (i = 0; i < 7; i++)
+		fspi_writel(f, 0, base + FSPI_AHBRX_BUF0CR0 + 4 * i);
+
+	/*
+	 * Set ADATSZ with the maximum AHB buffer size to improve the read
+	 * performance.
+	 */
+	fspi_writel(f, (f->devtype_data->ahb_buf_size / 8 |
+		  FSPI_AHBRXBUF0CR7_PREF), base + FSPI_AHBRX_BUF7CR0);
+
+	/* prefetch and no start address alignment limitation */
+	fspi_writel(f, FSPI_AHBCR_PREF_EN | FSPI_AHBCR_RDADDROPT,
+		 base + FSPI_AHBCR);
+
+	/* AHB Read - Set lut sequence ID for all CS. */
+	fspi_writel(f, SEQID_LUT, base + FSPI_FLSHA1CR2);
+	fspi_writel(f, SEQID_LUT, base + FSPI_FLSHA2CR2);
+	fspi_writel(f, SEQID_LUT, base + FSPI_FLSHB1CR2);
+	fspi_writel(f, SEQID_LUT, base + FSPI_FLSHB2CR2);
+
+	f->selected = -1;
+
+	/* enable the interrupt */
+	fspi_writel(f, FSPI_INTEN_IPCMDDONE, base + FSPI_INTEN);
+
+	return 0;
+}
+
+static const char *nxp_fspi_get_name(struct spi_mem *mem)
+{
+	struct nxp_fspi *f = spi_controller_get_devdata(mem->spi->master);
+	struct device *dev = &mem->spi->dev;
+	const char *name;
+
+	// Set custom name derived from the platform_device of the controller.
+	if (of_get_available_child_count(f->dev->of_node) == 1)
+		return dev_name(f->dev);
+
+	name = devm_kasprintf(dev, GFP_KERNEL,
+			      "%s-%d", dev_name(f->dev),
+			      mem->spi->chip_select);
+
+	if (!name) {
+		dev_err(dev, "failed to get memory for custom flash name\n");
+		return ERR_PTR(-ENOMEM);
+	}
+
+	return name;
+}
+
+static const struct spi_controller_mem_ops nxp_fspi_mem_ops = {
+	.adjust_op_size = nxp_fspi_adjust_op_size,
+	.supports_op = nxp_fspi_supports_op,
+	.exec_op = nxp_fspi_exec_op,
+	.get_name = nxp_fspi_get_name,
+};
+
+static int nxp_fspi_probe(struct platform_device *pdev)
+{
+	struct spi_controller *ctlr;
+	struct device *dev = &pdev->dev;
+	struct device_node *np = dev->of_node;
+	struct resource *res;
+	struct nxp_fspi *f;
+	int ret;
+
+	ctlr = spi_alloc_master(&pdev->dev, sizeof(*f));
+	if (!ctlr)
+		return -ENOMEM;
+
+	ctlr->mode_bits = SPI_RX_DUAL | SPI_RX_QUAD | SPI_RX_OCTAL |
+			  SPI_TX_DUAL | SPI_TX_QUAD | SPI_TX_OCTAL;
+
+	f = spi_controller_get_devdata(ctlr);
+	f->dev = dev;
+	f->devtype_data = of_device_get_match_data(dev);
+	if (!f->devtype_data) {
+		ret = -ENODEV;
+		goto err_put_ctrl;
+	}
+
+	platform_set_drvdata(pdev, f);
+
+	/* find the resources - configuration register address space */
+	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "fspi_base");
+	f->iobase = devm_ioremap_resource(dev, res);
+	if (IS_ERR(f->iobase)) {
+		ret = PTR_ERR(f->iobase);
+		goto err_put_ctrl;
+	}
+
+	/* find the resources - controller memory mapped space */
+	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "fspi_mmap");
+	f->ahb_addr = devm_ioremap_resource(dev, res);
+	if (IS_ERR(f->ahb_addr)) {
+		ret = PTR_ERR(f->ahb_addr);
+		goto err_put_ctrl;
+	}
+
+	/* assign memory mapped starting address and mapped size. */
+	f->memmap_phy = res->start;
+	f->memmap_phy_size = resource_size(res);
+
+	/* find the clocks */
+	f->clk_en = devm_clk_get(dev, "fspi_en");
+	if (IS_ERR(f->clk_en)) {
+		ret = PTR_ERR(f->clk_en);
+		goto err_put_ctrl;
+	}
+
+	f->clk = devm_clk_get(dev, "fspi");
+	if (IS_ERR(f->clk)) {
+		ret = PTR_ERR(f->clk);
+		goto err_put_ctrl;
+	}
+
+	ret = nxp_fspi_clk_prep_enable(f);
+	if (ret) {
+		dev_err(dev, "can not enable the clock\n");
+		goto err_put_ctrl;
+	}
+
+	/* find the irq */
+	ret = platform_get_irq(pdev, 0);
+	if (ret < 0) {
+		dev_err(dev, "failed to get the irq: %d\n", ret);
+		goto err_disable_clk;
+	}
+
+	ret = devm_request_irq(dev, ret,
+			nxp_fspi_irq_handler, 0, pdev->name, f);
+	if (ret) {
+		dev_err(dev, "failed to request irq: %d\n", ret);
+		goto err_disable_clk;
+	}
+
+	mutex_init(&f->lock);
+
+	ctlr->bus_num = -1;
+	ctlr->num_chipselect = NXP_FSPI_MAX_CHIPSELECT;
+	ctlr->mem_ops = &nxp_fspi_mem_ops;
+
+	nxp_fspi_default_setup(f);
+
+	ctlr->dev.of_node = np;
+
+	ret = spi_register_controller(ctlr);
+	if (ret)
+		goto err_destroy_mutex;
+
+	return 0;
+
+err_destroy_mutex:
+	mutex_destroy(&f->lock);
+
+err_disable_clk:
+	nxp_fspi_clk_disable_unprep(f);
+
+err_put_ctrl:
+	spi_controller_put(ctlr);
+
+	dev_err(dev, "NXP FSPI probe failed\n");
+	return ret;
+}
+
+static int nxp_fspi_remove(struct platform_device *pdev)
+{
+	struct nxp_fspi *f = platform_get_drvdata(pdev);
+
+	/* disable the hardware */
+	fspi_writel(f, FSPI_MCR0_MDIS, f->iobase + FSPI_MCR0);
+
+	nxp_fspi_clk_disable_unprep(f);
+
+	mutex_destroy(&f->lock);
+
+	return 0;
+}
+
+static int nxp_fspi_suspend(struct device *dev)
+{
+	return 0;
+}
+
+static int nxp_fspi_resume(struct device *dev)
+{
+	struct nxp_fspi *f = dev_get_drvdata(dev);
+
+	nxp_fspi_default_setup(f);
+
+	return 0;
+}
+
+static const struct of_device_id nxp_fspi_dt_ids[] = {
+	{ .compatible = "nxp,lx2160a-fspi", .data = (void *)&lx2160a_data, },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, nxp_fspi_dt_ids);
+
+static const struct dev_pm_ops nxp_fspi_pm_ops = {
+	.suspend	= nxp_fspi_suspend,
+	.resume		= nxp_fspi_resume,
+};
+
+static struct platform_driver nxp_fspi_driver = {
+	.driver = {
+		.name	= "nxp-fspi",
+		.of_match_table = nxp_fspi_dt_ids,
+		.pm =   &nxp_fspi_pm_ops,
+	},
+	.probe          = nxp_fspi_probe,
+	.remove		= nxp_fspi_remove,
+};
+module_platform_driver(nxp_fspi_driver);
+
+MODULE_DESCRIPTION("NXP FSPI Controller Driver");
+MODULE_AUTHOR("NXP Semiconductor");
+MODULE_AUTHOR("Yogesh Narayan Gaur <yogeshnarayan.gaur@nxp.com>");
+MODULE_AUTHOR("Boris Brezillon <bbrezillon@kernel.org>");
+MODULE_AUTHOR("Frieder Schrempf <frieder.schrempf@kontron.de>");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/spi/spi-omap2-mcspi.c b/drivers/spi/spi-omap2-mcspi.c
index 2fd8881fcd65..8be304379628 100644
--- a/drivers/spi/spi-omap2-mcspi.c
+++ b/drivers/spi/spi-omap2-mcspi.c
@@ -623,8 +623,8 @@ omap2_mcspi_txrx_dma(struct spi_device *spi, struct spi_transfer *xfer)
 	cfg.dst_addr = cs->phys + OMAP2_MCSPI_TX0;
 	cfg.src_addr_width = width;
 	cfg.dst_addr_width = width;
-	cfg.src_maxburst = es;
-	cfg.dst_maxburst = es;
+	cfg.src_maxburst = 1;
+	cfg.dst_maxburst = 1;
 
 	rx = xfer->rx_buf;
 	tx = xfer->tx_buf;
diff --git a/drivers/spi/spi-orion.c b/drivers/spi/spi-orion.c
index 7f280567093e..7d2e9bcc8b30 100644
--- a/drivers/spi/spi-orion.c
+++ b/drivers/spi/spi-orion.c
@@ -91,10 +91,6 @@ struct orion_direct_acc {
 	u32			size;
 };
 
-struct orion_child_options {
-	struct orion_direct_acc direct_access;
-};
-
 struct orion_spi {
 	struct spi_master	*master;
 	void __iomem		*base;
@@ -103,7 +99,7 @@ struct orion_spi {
 	const struct orion_spi_dev *devdata;
 	int			unused_hw_gpio;
 
-	struct orion_child_options	child[ORION_NUM_CHIPSELECTS];
+	struct orion_direct_acc	direct_access[ORION_NUM_CHIPSELECTS];
 };
 
 static inline void __iomem *spi_reg(struct orion_spi *orion_spi, u32 reg)
@@ -433,7 +429,7 @@ orion_spi_write_read(struct spi_device *spi, struct spi_transfer *xfer)
 	int cs = spi->chip_select;
 	void __iomem *vaddr;
 
-	word_len = spi->bits_per_word;
+	word_len = xfer->bits_per_word;
 	count = xfer->len;
 
 	orion_spi = spi_master_get_devdata(spi->master);
@@ -442,7 +438,7 @@ orion_spi_write_read(struct spi_device *spi, struct spi_transfer *xfer)
 	 * Use SPI direct write mode if base address is available. Otherwise
 	 * fall back to PIO mode for this transfer.
 	 */
-	vaddr = orion_spi->child[cs].direct_access.vaddr;
+	vaddr = orion_spi->direct_access[cs].vaddr;
 
 	if (vaddr && xfer->tx_buf && word_len == 8) {
 		unsigned int cnt = count / 4;
@@ -470,6 +466,8 @@ orion_spi_write_read(struct spi_device *spi, struct spi_transfer *xfer)
 			if (orion_spi_write_read_8bit(spi, &tx, &rx) < 0)
 				goto out;
 			count--;
+			if (xfer->word_delay_usecs)
+				udelay(xfer->word_delay_usecs);
 		} while (count);
 	} else if (word_len == 16) {
 		const u16 *tx = xfer->tx_buf;
@@ -479,6 +477,8 @@ orion_spi_write_read(struct spi_device *spi, struct spi_transfer *xfer)
 			if (orion_spi_write_read_16bit(spi, &tx, &rx) < 0)
 				goto out;
 			count -= 2;
+			if (xfer->word_delay_usecs)
+				udelay(xfer->word_delay_usecs);
 		} while (count);
 	}
 
@@ -683,7 +683,6 @@ static int orion_spi_probe(struct platform_device *pdev)
 	}
 
 	for_each_available_child_of_node(pdev->dev.of_node, np) {
-		struct orion_direct_acc *dir_acc;
 		u32 cs;
 		int cs_gpio;
 
@@ -751,13 +750,14 @@ static int orion_spi_probe(struct platform_device *pdev)
 		 * This needs to get extended for the direct SPI-NOR / SPI-NAND
 		 * support, once this gets implemented.
 		 */
-		dir_acc = &spi->child[cs].direct_access;
-		dir_acc->vaddr = devm_ioremap(&pdev->dev, r->start, PAGE_SIZE);
-		if (!dir_acc->vaddr) {
+		spi->direct_access[cs].vaddr = devm_ioremap(&pdev->dev,
+							    r->start,
+							    PAGE_SIZE);
+		if (!spi->direct_access[cs].vaddr) {
 			status = -ENOMEM;
 			goto out_rel_axi_clk;
 		}
-		dir_acc->size = PAGE_SIZE;
+		spi->direct_access[cs].size = PAGE_SIZE;
 
 		dev_info(&pdev->dev, "CS%d configured for direct access\n", cs);
 	}
diff --git a/drivers/spi/spi-pl022.c b/drivers/spi/spi-pl022.c
index 0c793e31d60f..26684178786f 100644
--- a/drivers/spi/spi-pl022.c
+++ b/drivers/spi/spi-pl022.c
@@ -253,6 +253,7 @@
 #define STATE_RUNNING			((void *) 1)
 #define STATE_DONE			((void *) 2)
 #define STATE_ERROR			((void *) -1)
+#define STATE_TIMEOUT			((void *) -2)
 
 /*
  * SSP State - Whether Enabled or Disabled
@@ -1484,6 +1485,30 @@ static void do_interrupt_dma_transfer(struct pl022 *pl022)
 	writew(irqflags, SSP_IMSC(pl022->virtbase));
 }
 
+static void print_current_status(struct pl022 *pl022)
+{
+	u32 read_cr0;
+	u16 read_cr1, read_dmacr, read_sr;
+
+	if (pl022->vendor->extended_cr)
+		read_cr0 = readl(SSP_CR0(pl022->virtbase));
+	else
+		read_cr0 = readw(SSP_CR0(pl022->virtbase));
+	read_cr1 = readw(SSP_CR1(pl022->virtbase));
+	read_dmacr = readw(SSP_DMACR(pl022->virtbase));
+	read_sr = readw(SSP_SR(pl022->virtbase));
+
+	dev_warn(&pl022->adev->dev, "spi-pl022 CR0: %x\n", read_cr0);
+	dev_warn(&pl022->adev->dev, "spi-pl022 CR1: %x\n", read_cr1);
+	dev_warn(&pl022->adev->dev, "spi-pl022 DMACR: %x\n", read_dmacr);
+	dev_warn(&pl022->adev->dev, "spi-pl022 SR: %x\n", read_sr);
+	dev_warn(&pl022->adev->dev,
+			"spi-pl022 exp_fifo_level/fifodepth: %u/%d\n",
+			pl022->exp_fifo_level,
+			pl022->vendor->fifodepth);
+
+}
+
 static void do_polling_transfer(struct pl022 *pl022)
 {
 	struct spi_message *message = NULL;
@@ -1535,7 +1560,8 @@ static void do_polling_transfer(struct pl022 *pl022)
 			if (time_after(time, timeout)) {
 				dev_warn(&pl022->adev->dev,
 				"%s: timeout!\n", __func__);
-				message->state = STATE_ERROR;
+				message->state = STATE_TIMEOUT;
+				print_current_status(pl022);
 				goto out;
 			}
 			cpu_relax();
@@ -1553,6 +1579,8 @@ static void do_polling_transfer(struct pl022 *pl022)
 	/* Handle end of message */
 	if (message->state == STATE_DONE)
 		message->status = 0;
+	else if (message->state == STATE_TIMEOUT)
+		message->status = -EAGAIN;
 	else
 		message->status = -EIO;
 
diff --git a/drivers/spi/spi-pxa2xx-dma.c b/drivers/spi/spi-pxa2xx-dma.c
index 2fa7f4b43492..15592598273e 100644
--- a/drivers/spi/spi-pxa2xx-dma.c
+++ b/drivers/spi/spi-pxa2xx-dma.c
@@ -23,7 +23,7 @@
 static void pxa2xx_spi_dma_transfer_complete(struct driver_data *drv_data,
 					     bool error)
 {
-	struct spi_message *msg = drv_data->master->cur_msg;
+	struct spi_message *msg = drv_data->controller->cur_msg;
 
 	/*
 	 * It is possible that one CPU is handling ROR interrupt and other
@@ -59,7 +59,7 @@ static void pxa2xx_spi_dma_transfer_complete(struct driver_data *drv_data,
 			msg->status = -EIO;
 		}
 
-		spi_finalize_current_transfer(drv_data->master);
+		spi_finalize_current_transfer(drv_data->controller);
 	}
 }
 
@@ -74,7 +74,7 @@ pxa2xx_spi_dma_prepare_one(struct driver_data *drv_data,
 			   struct spi_transfer *xfer)
 {
 	struct chip_data *chip =
-		spi_get_ctldata(drv_data->master->cur_msg->spi);
+		spi_get_ctldata(drv_data->controller->cur_msg->spi);
 	enum dma_slave_buswidth width;
 	struct dma_slave_config cfg;
 	struct dma_chan *chan;
@@ -102,14 +102,14 @@ pxa2xx_spi_dma_prepare_one(struct driver_data *drv_data,
 		cfg.dst_maxburst = chip->dma_burst_size;
 
 		sgt = &xfer->tx_sg;
-		chan = drv_data->master->dma_tx;
+		chan = drv_data->controller->dma_tx;
 	} else {
 		cfg.src_addr = drv_data->ssdr_physical;
 		cfg.src_addr_width = width;
 		cfg.src_maxburst = chip->dma_burst_size;
 
 		sgt = &xfer->rx_sg;
-		chan = drv_data->master->dma_rx;
+		chan = drv_data->controller->dma_rx;
 	}
 
 	ret = dmaengine_slave_config(chan, &cfg);
@@ -130,8 +130,8 @@ irqreturn_t pxa2xx_spi_dma_transfer(struct driver_data *drv_data)
 	if (status & SSSR_ROR) {
 		dev_err(&drv_data->pdev->dev, "FIFO overrun\n");
 
-		dmaengine_terminate_async(drv_data->master->dma_rx);
-		dmaengine_terminate_async(drv_data->master->dma_tx);
+		dmaengine_terminate_async(drv_data->controller->dma_rx);
+		dmaengine_terminate_async(drv_data->controller->dma_tx);
 
 		pxa2xx_spi_dma_transfer_complete(drv_data, true);
 		return IRQ_HANDLED;
@@ -171,15 +171,15 @@ int pxa2xx_spi_dma_prepare(struct driver_data *drv_data,
 	return 0;
 
 err_rx:
-	dmaengine_terminate_async(drv_data->master->dma_tx);
+	dmaengine_terminate_async(drv_data->controller->dma_tx);
 err_tx:
 	return err;
 }
 
 void pxa2xx_spi_dma_start(struct driver_data *drv_data)
 {
-	dma_async_issue_pending(drv_data->master->dma_rx);
-	dma_async_issue_pending(drv_data->master->dma_tx);
+	dma_async_issue_pending(drv_data->controller->dma_rx);
+	dma_async_issue_pending(drv_data->controller->dma_tx);
 
 	atomic_set(&drv_data->dma_running, 1);
 }
@@ -187,30 +187,30 @@ void pxa2xx_spi_dma_start(struct driver_data *drv_data)
 void pxa2xx_spi_dma_stop(struct driver_data *drv_data)
 {
 	atomic_set(&drv_data->dma_running, 0);
-	dmaengine_terminate_sync(drv_data->master->dma_rx);
-	dmaengine_terminate_sync(drv_data->master->dma_tx);
+	dmaengine_terminate_sync(drv_data->controller->dma_rx);
+	dmaengine_terminate_sync(drv_data->controller->dma_tx);
 }
 
 int pxa2xx_spi_dma_setup(struct driver_data *drv_data)
 {
-	struct pxa2xx_spi_master *pdata = drv_data->master_info;
+	struct pxa2xx_spi_controller *pdata = drv_data->controller_info;
 	struct device *dev = &drv_data->pdev->dev;
-	struct spi_controller *master = drv_data->master;
+	struct spi_controller *controller = drv_data->controller;
 	dma_cap_mask_t mask;
 
 	dma_cap_zero(mask);
 	dma_cap_set(DMA_SLAVE, mask);
 
-	master->dma_tx = dma_request_slave_channel_compat(mask,
+	controller->dma_tx = dma_request_slave_channel_compat(mask,
 				pdata->dma_filter, pdata->tx_param, dev, "tx");
-	if (!master->dma_tx)
+	if (!controller->dma_tx)
 		return -ENODEV;
 
-	master->dma_rx = dma_request_slave_channel_compat(mask,
+	controller->dma_rx = dma_request_slave_channel_compat(mask,
 				pdata->dma_filter, pdata->rx_param, dev, "rx");
-	if (!master->dma_rx) {
-		dma_release_channel(master->dma_tx);
-		master->dma_tx = NULL;
+	if (!controller->dma_rx) {
+		dma_release_channel(controller->dma_tx);
+		controller->dma_tx = NULL;
 		return -ENODEV;
 	}
 
@@ -219,17 +219,17 @@ int pxa2xx_spi_dma_setup(struct driver_data *drv_data)
 
 void pxa2xx_spi_dma_release(struct driver_data *drv_data)
 {
-	struct spi_controller *master = drv_data->master;
+	struct spi_controller *controller = drv_data->controller;
 
-	if (master->dma_rx) {
-		dmaengine_terminate_sync(master->dma_rx);
-		dma_release_channel(master->dma_rx);
-		master->dma_rx = NULL;
+	if (controller->dma_rx) {
+		dmaengine_terminate_sync(controller->dma_rx);
+		dma_release_channel(controller->dma_rx);
+		controller->dma_rx = NULL;
 	}
-	if (master->dma_tx) {
-		dmaengine_terminate_sync(master->dma_tx);
-		dma_release_channel(master->dma_tx);
-		master->dma_tx = NULL;
+	if (controller->dma_tx) {
+		dmaengine_terminate_sync(controller->dma_tx);
+		dma_release_channel(controller->dma_tx);
+		controller->dma_tx = NULL;
 	}
 }
 
diff --git a/drivers/spi/spi-pxa2xx-pci.c b/drivers/spi/spi-pxa2xx-pci.c
index 869f188b02eb..1727fdfbac28 100644
--- a/drivers/spi/spi-pxa2xx-pci.c
+++ b/drivers/spi/spi-pxa2xx-pci.c
@@ -197,7 +197,7 @@ static int pxa2xx_spi_pci_probe(struct pci_dev *dev,
 	struct platform_device_info pi;
 	int ret;
 	struct platform_device *pdev;
-	struct pxa2xx_spi_master spi_pdata;
+	struct pxa2xx_spi_controller spi_pdata;
 	struct ssp_device *ssp;
 	struct pxa_spi_info *c;
 	char buf[40];
@@ -265,7 +265,7 @@ static int pxa2xx_spi_pci_probe(struct pci_dev *dev,
 static void pxa2xx_spi_pci_remove(struct pci_dev *dev)
 {
 	struct platform_device *pdev = pci_get_drvdata(dev);
-	struct pxa2xx_spi_master *spi_pdata;
+	struct pxa2xx_spi_controller *spi_pdata;
 
 	spi_pdata = dev_get_platdata(&pdev->dev);
 
diff --git a/drivers/spi/spi-pxa2xx.c b/drivers/spi/spi-pxa2xx.c
index d84b893a64d7..b6ddba833d02 100644
--- a/drivers/spi/spi-pxa2xx.c
+++ b/drivers/spi/spi-pxa2xx.c
@@ -328,7 +328,7 @@ static void lpss_ssp_setup(struct driver_data *drv_data)
 	__lpss_ssp_write_priv(drv_data, config->reg_cs_ctrl, value);
 
 	/* Enable multiblock DMA transfers */
-	if (drv_data->master_info->enable_dma) {
+	if (drv_data->controller_info->enable_dma) {
 		__lpss_ssp_write_priv(drv_data, config->reg_ssp, 1);
 
 		if (config->reg_general >= 0) {
@@ -368,7 +368,7 @@ static void lpss_ssp_select_cs(struct spi_device *spi,
 		__lpss_ssp_write_priv(drv_data,
 				      config->reg_cs_ctrl, value);
 		ndelay(1000000000 /
-		       (drv_data->master->max_speed_hz / 2));
+		       (drv_data->controller->max_speed_hz / 2));
 	}
 }
 
@@ -567,7 +567,7 @@ static int u32_reader(struct driver_data *drv_data)
 static void reset_sccr1(struct driver_data *drv_data)
 {
 	struct chip_data *chip =
-		spi_get_ctldata(drv_data->master->cur_msg->spi);
+		spi_get_ctldata(drv_data->controller->cur_msg->spi);
 	u32 sccr1_reg;
 
 	sccr1_reg = pxa2xx_spi_read(drv_data, SSCR1) & ~drv_data->int_cr1;
@@ -599,8 +599,8 @@ static void int_error_stop(struct driver_data *drv_data, const char* msg)
 
 	dev_err(&drv_data->pdev->dev, "%s\n", msg);
 
-	drv_data->master->cur_msg->status = -EIO;
-	spi_finalize_current_transfer(drv_data->master);
+	drv_data->controller->cur_msg->status = -EIO;
+	spi_finalize_current_transfer(drv_data->controller);
 }
 
 static void int_transfer_complete(struct driver_data *drv_data)
@@ -611,7 +611,7 @@ static void int_transfer_complete(struct driver_data *drv_data)
 	if (!pxa25x_ssp_comp(drv_data))
 		pxa2xx_spi_write(drv_data, SSTO, 0);
 
-	spi_finalize_current_transfer(drv_data->master);
+	spi_finalize_current_transfer(drv_data->controller);
 }
 
 static irqreturn_t interrupt_transfer(struct driver_data *drv_data)
@@ -747,7 +747,7 @@ static irqreturn_t ssp_int(int irq, void *dev_id)
 	pxa2xx_spi_write(drv_data, SSCR1, sccr1_reg & ~drv_data->int_cr1);
 	pxa2xx_spi_write(drv_data, SSCR1, sccr1_reg);
 
-	if (!drv_data->master->cur_msg) {
+	if (!drv_data->controller->cur_msg) {
 		handle_bad_msg(drv_data);
 		/* Never fail */
 		return IRQ_HANDLED;
@@ -879,7 +879,7 @@ static unsigned int quark_x1000_get_clk_div(int rate, u32 *dds)
 
 static unsigned int ssp_get_clk_div(struct driver_data *drv_data, int rate)
 {
-	unsigned long ssp_clk = drv_data->master->max_speed_hz;
+	unsigned long ssp_clk = drv_data->controller->max_speed_hz;
 	const struct ssp_device *ssp = drv_data->ssp;
 
 	rate = min_t(int, ssp_clk, rate);
@@ -894,7 +894,7 @@ static unsigned int pxa2xx_ssp_get_clk_div(struct driver_data *drv_data,
 					   int rate)
 {
 	struct chip_data *chip =
-		spi_get_ctldata(drv_data->master->cur_msg->spi);
+		spi_get_ctldata(drv_data->controller->cur_msg->spi);
 	unsigned int clk_div;
 
 	switch (drv_data->ssp_type) {
@@ -908,7 +908,7 @@ static unsigned int pxa2xx_ssp_get_clk_div(struct driver_data *drv_data,
 	return clk_div << 8;
 }
 
-static bool pxa2xx_spi_can_dma(struct spi_controller *master,
+static bool pxa2xx_spi_can_dma(struct spi_controller *controller,
 			       struct spi_device *spi,
 			       struct spi_transfer *xfer)
 {
@@ -919,12 +919,12 @@ static bool pxa2xx_spi_can_dma(struct spi_controller *master,
 	       xfer->len >= chip->dma_burst_size;
 }
 
-static int pxa2xx_spi_transfer_one(struct spi_controller *master,
+static int pxa2xx_spi_transfer_one(struct spi_controller *controller,
 				   struct spi_device *spi,
 				   struct spi_transfer *transfer)
 {
-	struct driver_data *drv_data = spi_controller_get_devdata(master);
-	struct spi_message *message = master->cur_msg;
+	struct driver_data *drv_data = spi_controller_get_devdata(controller);
+	struct spi_message *message = controller->cur_msg;
 	struct chip_data *chip = spi_get_ctldata(message->spi);
 	u32 dma_thresh = chip->dma_threshold;
 	u32 dma_burst = chip->dma_burst_size;
@@ -1006,9 +1006,9 @@ static int pxa2xx_spi_transfer_one(struct spi_controller *master,
 					     "DMA burst size reduced to match bits_per_word\n");
 	}
 
-	dma_mapped = master->can_dma &&
-		     master->can_dma(master, message->spi, transfer) &&
-		     master->cur_msg_mapped;
+	dma_mapped = controller->can_dma &&
+		     controller->can_dma(controller, message->spi, transfer) &&
+		     controller->cur_msg_mapped;
 	if (dma_mapped) {
 
 		/* Ensure we have the correct interrupt handler */
@@ -1036,12 +1036,12 @@ static int pxa2xx_spi_transfer_one(struct spi_controller *master,
 	cr0 = pxa2xx_configure_sscr0(drv_data, clk_div, bits);
 	if (!pxa25x_ssp_comp(drv_data))
 		dev_dbg(&message->spi->dev, "%u Hz actual, %s\n",
-			master->max_speed_hz
+			controller->max_speed_hz
 				/ (1 + ((cr0 & SSCR0_SCR(0xfff)) >> 8)),
 			dma_mapped ? "DMA" : "PIO");
 	else
 		dev_dbg(&message->spi->dev, "%u Hz actual, %s\n",
-			master->max_speed_hz / 2
+			controller->max_speed_hz / 2
 				/ (1 + ((cr0 & SSCR0_SCR(0x0ff)) >> 8)),
 			dma_mapped ? "DMA" : "PIO");
 
@@ -1092,7 +1092,7 @@ static int pxa2xx_spi_transfer_one(struct spi_controller *master,
 		}
 	}
 
-	if (spi_controller_is_slave(master)) {
+	if (spi_controller_is_slave(controller)) {
 		while (drv_data->write(drv_data))
 			;
 		if (drv_data->gpiod_ready) {
@@ -1111,9 +1111,9 @@ static int pxa2xx_spi_transfer_one(struct spi_controller *master,
 	return 1;
 }
 
-static int pxa2xx_spi_slave_abort(struct spi_master *master)
+static int pxa2xx_spi_slave_abort(struct spi_controller *controller)
 {
-	struct driver_data *drv_data = spi_controller_get_devdata(master);
+	struct driver_data *drv_data = spi_controller_get_devdata(controller);
 
 	/* Stop and reset SSP */
 	write_SSSR_CS(drv_data, drv_data->clear_sr);
@@ -1126,16 +1126,16 @@ static int pxa2xx_spi_slave_abort(struct spi_master *master)
 
 	dev_dbg(&drv_data->pdev->dev, "transfer aborted\n");
 
-	drv_data->master->cur_msg->status = -EINTR;
-	spi_finalize_current_transfer(drv_data->master);
+	drv_data->controller->cur_msg->status = -EINTR;
+	spi_finalize_current_transfer(drv_data->controller);
 
 	return 0;
 }
 
-static void pxa2xx_spi_handle_err(struct spi_controller *master,
+static void pxa2xx_spi_handle_err(struct spi_controller *controller,
 				 struct spi_message *msg)
 {
-	struct driver_data *drv_data = spi_controller_get_devdata(master);
+	struct driver_data *drv_data = spi_controller_get_devdata(controller);
 
 	/* Disable the SSP */
 	pxa2xx_spi_write(drv_data, SSCR0,
@@ -1159,9 +1159,9 @@ static void pxa2xx_spi_handle_err(struct spi_controller *master,
 		pxa2xx_spi_dma_stop(drv_data);
 }
 
-static int pxa2xx_spi_unprepare_transfer(struct spi_controller *master)
+static int pxa2xx_spi_unprepare_transfer(struct spi_controller *controller)
 {
-	struct driver_data *drv_data = spi_controller_get_devdata(master);
+	struct driver_data *drv_data = spi_controller_get_devdata(controller);
 
 	/* Disable the SSP now */
 	pxa2xx_spi_write(drv_data, SSCR0,
@@ -1260,7 +1260,7 @@ static int setup(struct spi_device *spi)
 		break;
 	default:
 		tx_hi_thres = 0;
-		if (spi_controller_is_slave(drv_data->master)) {
+		if (spi_controller_is_slave(drv_data->controller)) {
 			tx_thres = 1;
 			rx_thres = 2;
 		} else {
@@ -1287,7 +1287,7 @@ static int setup(struct spi_device *spi)
 
 			chip->frm = spi->chip_select;
 		}
-		chip->enable_dma = drv_data->master_info->enable_dma;
+		chip->enable_dma = drv_data->controller_info->enable_dma;
 		chip->timeout = TIMOUT_DFLT;
 	}
 
@@ -1310,7 +1310,7 @@ static int setup(struct spi_device *spi)
 		if (chip_info->enable_loopback)
 			chip->cr1 = SSCR1_LBM;
 	}
-	if (spi_controller_is_slave(drv_data->master)) {
+	if (spi_controller_is_slave(drv_data->controller)) {
 		chip->cr1 |= SSCR1_SCFR;
 		chip->cr1 |= SSCR1_SCLKDIR;
 		chip->cr1 |= SSCR1_SFRMDIR;
@@ -1497,10 +1497,10 @@ static bool pxa2xx_spi_idma_filter(struct dma_chan *chan, void *param)
 
 #endif /* CONFIG_PCI */
 
-static struct pxa2xx_spi_master *
+static struct pxa2xx_spi_controller *
 pxa2xx_spi_init_pdata(struct platform_device *pdev)
 {
-	struct pxa2xx_spi_master *pdata;
+	struct pxa2xx_spi_controller *pdata;
 	struct acpi_device *adev;
 	struct ssp_device *ssp;
 	struct resource *res;
@@ -1568,10 +1568,10 @@ pxa2xx_spi_init_pdata(struct platform_device *pdev)
 	return pdata;
 }
 
-static int pxa2xx_spi_fw_translate_cs(struct spi_controller *master,
+static int pxa2xx_spi_fw_translate_cs(struct spi_controller *controller,
 				      unsigned int cs)
 {
-	struct driver_data *drv_data = spi_controller_get_devdata(master);
+	struct driver_data *drv_data = spi_controller_get_devdata(controller);
 
 	if (has_acpi_companion(&drv_data->pdev->dev)) {
 		switch (drv_data->ssp_type) {
@@ -1595,8 +1595,8 @@ static int pxa2xx_spi_fw_translate_cs(struct spi_controller *master,
 static int pxa2xx_spi_probe(struct platform_device *pdev)
 {
 	struct device *dev = &pdev->dev;
-	struct pxa2xx_spi_master *platform_info;
-	struct spi_controller *master;
+	struct pxa2xx_spi_controller *platform_info;
+	struct spi_controller *controller;
 	struct driver_data *drv_data;
 	struct ssp_device *ssp;
 	const struct lpss_config *config;
@@ -1622,37 +1622,37 @@ static int pxa2xx_spi_probe(struct platform_device *pdev)
 	}
 
 	if (platform_info->is_slave)
-		master = spi_alloc_slave(dev, sizeof(struct driver_data));
+		controller = spi_alloc_slave(dev, sizeof(struct driver_data));
 	else
-		master = spi_alloc_master(dev, sizeof(struct driver_data));
+		controller = spi_alloc_master(dev, sizeof(struct driver_data));
 
-	if (!master) {
-		dev_err(&pdev->dev, "cannot alloc spi_master\n");
+	if (!controller) {
+		dev_err(&pdev->dev, "cannot alloc spi_controller\n");
 		pxa_ssp_free(ssp);
 		return -ENOMEM;
 	}
-	drv_data = spi_controller_get_devdata(master);
-	drv_data->master = master;
-	drv_data->master_info = platform_info;
+	drv_data = spi_controller_get_devdata(controller);
+	drv_data->controller = controller;
+	drv_data->controller_info = platform_info;
 	drv_data->pdev = pdev;
 	drv_data->ssp = ssp;
 
-	master->dev.of_node = pdev->dev.of_node;
+	controller->dev.of_node = pdev->dev.of_node;
 	/* the spi->mode bits understood by this driver: */
-	master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH | SPI_LOOP;
-
-	master->bus_num = ssp->port_id;
-	master->dma_alignment = DMA_ALIGNMENT;
-	master->cleanup = cleanup;
-	master->setup = setup;
-	master->set_cs = pxa2xx_spi_set_cs;
-	master->transfer_one = pxa2xx_spi_transfer_one;
-	master->slave_abort = pxa2xx_spi_slave_abort;
-	master->handle_err = pxa2xx_spi_handle_err;
-	master->unprepare_transfer_hardware = pxa2xx_spi_unprepare_transfer;
-	master->fw_translate_cs = pxa2xx_spi_fw_translate_cs;
-	master->auto_runtime_pm = true;
-	master->flags = SPI_CONTROLLER_MUST_RX | SPI_CONTROLLER_MUST_TX;
+	controller->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH | SPI_LOOP;
+
+	controller->bus_num = ssp->port_id;
+	controller->dma_alignment = DMA_ALIGNMENT;
+	controller->cleanup = cleanup;
+	controller->setup = setup;
+	controller->set_cs = pxa2xx_spi_set_cs;
+	controller->transfer_one = pxa2xx_spi_transfer_one;
+	controller->slave_abort = pxa2xx_spi_slave_abort;
+	controller->handle_err = pxa2xx_spi_handle_err;
+	controller->unprepare_transfer_hardware = pxa2xx_spi_unprepare_transfer;
+	controller->fw_translate_cs = pxa2xx_spi_fw_translate_cs;
+	controller->auto_runtime_pm = true;
+	controller->flags = SPI_CONTROLLER_MUST_RX | SPI_CONTROLLER_MUST_TX;
 
 	drv_data->ssp_type = ssp->type;
 
@@ -1661,10 +1661,10 @@ static int pxa2xx_spi_probe(struct platform_device *pdev)
 	if (pxa25x_ssp_comp(drv_data)) {
 		switch (drv_data->ssp_type) {
 		case QUARK_X1000_SSP:
-			master->bits_per_word_mask = SPI_BPW_RANGE_MASK(4, 32);
+			controller->bits_per_word_mask = SPI_BPW_RANGE_MASK(4, 32);
 			break;
 		default:
-			master->bits_per_word_mask = SPI_BPW_RANGE_MASK(4, 16);
+			controller->bits_per_word_mask = SPI_BPW_RANGE_MASK(4, 16);
 			break;
 		}
 
@@ -1673,7 +1673,7 @@ static int pxa2xx_spi_probe(struct platform_device *pdev)
 		drv_data->clear_sr = SSSR_ROR;
 		drv_data->mask_sr = SSSR_RFS | SSSR_TFS | SSSR_ROR;
 	} else {
-		master->bits_per_word_mask = SPI_BPW_RANGE_MASK(4, 32);
+		controller->bits_per_word_mask = SPI_BPW_RANGE_MASK(4, 32);
 		drv_data->int_cr1 = SSCR1_TIE | SSCR1_RIE | SSCR1_TINTE;
 		drv_data->dma_cr1 = DEFAULT_DMA_CR1;
 		drv_data->clear_sr = SSSR_ROR | SSSR_TINT;
@@ -1685,7 +1685,7 @@ static int pxa2xx_spi_probe(struct platform_device *pdev)
 			drv_data);
 	if (status < 0) {
 		dev_err(&pdev->dev, "cannot get IRQ %d\n", ssp->irq);
-		goto out_error_master_alloc;
+		goto out_error_controller_alloc;
 	}
 
 	/* Setup DMA if requested */
@@ -1695,7 +1695,8 @@ static int pxa2xx_spi_probe(struct platform_device *pdev)
 			dev_dbg(dev, "no DMA channels available, using PIO\n");
 			platform_info->enable_dma = false;
 		} else {
-			master->can_dma = pxa2xx_spi_can_dma;
+			controller->can_dma = pxa2xx_spi_can_dma;
+			controller->max_dma_len = MAX_DMA_LEN;
 		}
 	}
 
@@ -1704,7 +1705,7 @@ static int pxa2xx_spi_probe(struct platform_device *pdev)
 	if (status)
 		goto out_error_dma_irq_alloc;
 
-	master->max_speed_hz = clk_get_rate(ssp->clk);
+	controller->max_speed_hz = clk_get_rate(ssp->clk);
 
 	/* Load default SSP configuration */
 	pxa2xx_spi_write(drv_data, SSCR0, 0);
@@ -1727,7 +1728,7 @@ static int pxa2xx_spi_probe(struct platform_device *pdev)
 		break;
 	default:
 
-		if (spi_controller_is_slave(master)) {
+		if (spi_controller_is_slave(controller)) {
 			tmp = SSCR1_SCFR |
 			      SSCR1_SCLKDIR |
 			      SSCR1_SFRMDIR |
@@ -1740,7 +1741,7 @@ static int pxa2xx_spi_probe(struct platform_device *pdev)
 		}
 		pxa2xx_spi_write(drv_data, SSCR1, tmp);
 		tmp = SSCR0_Motorola | SSCR0_DataSize(8);
-		if (!spi_controller_is_slave(master))
+		if (!spi_controller_is_slave(controller))
 			tmp |= SSCR0_SCR(2);
 		pxa2xx_spi_write(drv_data, SSCR0, tmp);
 		break;
@@ -1765,24 +1766,24 @@ static int pxa2xx_spi_probe(struct platform_device *pdev)
 			platform_info->num_chipselect = config->cs_num;
 		}
 	}
-	master->num_chipselect = platform_info->num_chipselect;
+	controller->num_chipselect = platform_info->num_chipselect;
 
 	count = gpiod_count(&pdev->dev, "cs");
 	if (count > 0) {
 		int i;
 
-		master->num_chipselect = max_t(int, count,
-			master->num_chipselect);
+		controller->num_chipselect = max_t(int, count,
+			controller->num_chipselect);
 
 		drv_data->cs_gpiods = devm_kcalloc(&pdev->dev,
-			master->num_chipselect, sizeof(struct gpio_desc *),
+			controller->num_chipselect, sizeof(struct gpio_desc *),
 			GFP_KERNEL);
 		if (!drv_data->cs_gpiods) {
 			status = -ENOMEM;
 			goto out_error_clock_enabled;
 		}
 
-		for (i = 0; i < master->num_chipselect; i++) {
+		for (i = 0; i < controller->num_chipselect; i++) {
 			struct gpio_desc *gpiod;
 
 			gpiod = devm_gpiod_get_index(dev, "cs", i, GPIOD_ASIS);
@@ -1815,9 +1816,9 @@ static int pxa2xx_spi_probe(struct platform_device *pdev)
 
 	/* Register with the SPI framework */
 	platform_set_drvdata(pdev, drv_data);
-	status = devm_spi_register_controller(&pdev->dev, master);
+	status = devm_spi_register_controller(&pdev->dev, controller);
 	if (status != 0) {
-		dev_err(&pdev->dev, "problem registering spi master\n");
+		dev_err(&pdev->dev, "problem registering spi controller\n");
 		goto out_error_clock_enabled;
 	}
 
@@ -1832,8 +1833,8 @@ static int pxa2xx_spi_probe(struct platform_device *pdev)
 	pxa2xx_spi_dma_release(drv_data);
 	free_irq(ssp->irq, drv_data);
 
-out_error_master_alloc:
-	spi_controller_put(master);
+out_error_controller_alloc:
+	spi_controller_put(controller);
 	pxa_ssp_free(ssp);
 	return status;
 }
@@ -1854,7 +1855,7 @@ static int pxa2xx_spi_remove(struct platform_device *pdev)
 	clk_disable_unprepare(ssp->clk);
 
 	/* Release DMA */
-	if (drv_data->master_info->enable_dma)
+	if (drv_data->controller_info->enable_dma)
 		pxa2xx_spi_dma_release(drv_data);
 
 	pm_runtime_put_noidle(&pdev->dev);
@@ -1876,7 +1877,7 @@ static int pxa2xx_spi_suspend(struct device *dev)
 	struct ssp_device *ssp = drv_data->ssp;
 	int status;
 
-	status = spi_controller_suspend(drv_data->master);
+	status = spi_controller_suspend(drv_data->controller);
 	if (status != 0)
 		return status;
 	pxa2xx_spi_write(drv_data, SSCR0, 0);
@@ -1901,7 +1902,7 @@ static int pxa2xx_spi_resume(struct device *dev)
 	}
 
 	/* Start the queue running */
-	return spi_controller_resume(drv_data->master);
+	return spi_controller_resume(drv_data->controller);
 }
 #endif
 
diff --git a/drivers/spi/spi-pxa2xx.h b/drivers/spi/spi-pxa2xx.h
index 4e324da66ef7..aba777b4502d 100644
--- a/drivers/spi/spi-pxa2xx.h
+++ b/drivers/spi/spi-pxa2xx.h
@@ -31,10 +31,10 @@ struct driver_data {
 
 	/* SPI framework hookup */
 	enum pxa_ssp_type ssp_type;
-	struct spi_controller *master;
+	struct spi_controller *controller;
 
 	/* PXA hookup */
-	struct pxa2xx_spi_master *master_info;
+	struct pxa2xx_spi_controller *controller_info;
 
 	/* SSP register addresses */
 	void __iomem *ioaddr;
diff --git a/drivers/spi/spi-rspi.c b/drivers/spi/spi-rspi.c
index a4ef641b5227..556870dcdf79 100644
--- a/drivers/spi/spi-rspi.c
+++ b/drivers/spi/spi-rspi.c
@@ -180,7 +180,7 @@
 struct rspi_data {
 	void __iomem *addr;
 	u32 max_speed_hz;
-	struct spi_master *master;
+	struct spi_controller *ctlr;
 	wait_queue_head_t wait;
 	struct clk *clk;
 	u16 spcmd;
@@ -237,8 +237,8 @@ static u16 rspi_read_data(const struct rspi_data *rspi)
 /* optional functions */
 struct spi_ops {
 	int (*set_config_register)(struct rspi_data *rspi, int access_size);
-	int (*transfer_one)(struct spi_master *master, struct spi_device *spi,
-			    struct spi_transfer *xfer);
+	int (*transfer_one)(struct spi_controller *ctlr,
+			    struct spi_device *spi, struct spi_transfer *xfer);
 	u16 mode_bits;
 	u16 flags;
 	u16 fifo_size;
@@ -466,7 +466,7 @@ static int rspi_data_out(struct rspi_data *rspi, u8 data)
 {
 	int error = rspi_wait_for_tx_empty(rspi);
 	if (error < 0) {
-		dev_err(&rspi->master->dev, "transmit timeout\n");
+		dev_err(&rspi->ctlr->dev, "transmit timeout\n");
 		return error;
 	}
 	rspi_write_data(rspi, data);
@@ -480,7 +480,7 @@ static int rspi_data_in(struct rspi_data *rspi)
 
 	error = rspi_wait_for_rx_full(rspi);
 	if (error < 0) {
-		dev_err(&rspi->master->dev, "receive timeout\n");
+		dev_err(&rspi->ctlr->dev, "receive timeout\n");
 		return error;
 	}
 	data = rspi_read_data(rspi);
@@ -526,8 +526,8 @@ static int rspi_dma_transfer(struct rspi_data *rspi, struct sg_table *tx,
 
 	/* First prepare and submit the DMA request(s), as this may fail */
 	if (rx) {
-		desc_rx = dmaengine_prep_slave_sg(rspi->master->dma_rx,
-					rx->sgl, rx->nents, DMA_DEV_TO_MEM,
+		desc_rx = dmaengine_prep_slave_sg(rspi->ctlr->dma_rx, rx->sgl,
+					rx->nents, DMA_DEV_TO_MEM,
 					DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
 		if (!desc_rx) {
 			ret = -EAGAIN;
@@ -546,8 +546,8 @@ static int rspi_dma_transfer(struct rspi_data *rspi, struct sg_table *tx,
 	}
 
 	if (tx) {
-		desc_tx = dmaengine_prep_slave_sg(rspi->master->dma_tx,
-					tx->sgl, tx->nents, DMA_MEM_TO_DEV,
+		desc_tx = dmaengine_prep_slave_sg(rspi->ctlr->dma_tx, tx->sgl,
+					tx->nents, DMA_MEM_TO_DEV,
 					DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
 		if (!desc_tx) {
 			ret = -EAGAIN;
@@ -584,9 +584,9 @@ static int rspi_dma_transfer(struct rspi_data *rspi, struct sg_table *tx,
 
 	/* Now start DMA */
 	if (rx)
-		dma_async_issue_pending(rspi->master->dma_rx);
+		dma_async_issue_pending(rspi->ctlr->dma_rx);
 	if (tx)
-		dma_async_issue_pending(rspi->master->dma_tx);
+		dma_async_issue_pending(rspi->ctlr->dma_tx);
 
 	ret = wait_event_interruptible_timeout(rspi->wait,
 					       rspi->dma_callbacked, HZ);
@@ -594,13 +594,13 @@ static int rspi_dma_transfer(struct rspi_data *rspi, struct sg_table *tx,
 		ret = 0;
 	} else {
 		if (!ret) {
-			dev_err(&rspi->master->dev, "DMA timeout\n");
+			dev_err(&rspi->ctlr->dev, "DMA timeout\n");
 			ret = -ETIMEDOUT;
 		}
 		if (tx)
-			dmaengine_terminate_all(rspi->master->dma_tx);
+			dmaengine_terminate_all(rspi->ctlr->dma_tx);
 		if (rx)
-			dmaengine_terminate_all(rspi->master->dma_rx);
+			dmaengine_terminate_all(rspi->ctlr->dma_rx);
 	}
 
 	rspi_disable_irq(rspi, irq_mask);
@@ -614,12 +614,12 @@ static int rspi_dma_transfer(struct rspi_data *rspi, struct sg_table *tx,
 
 no_dma_tx:
 	if (rx)
-		dmaengine_terminate_all(rspi->master->dma_rx);
+		dmaengine_terminate_all(rspi->ctlr->dma_rx);
 no_dma_rx:
 	if (ret == -EAGAIN) {
 		pr_warn_once("%s %s: DMA not available, falling back to PIO\n",
-			     dev_driver_string(&rspi->master->dev),
-			     dev_name(&rspi->master->dev));
+			     dev_driver_string(&rspi->ctlr->dev),
+			     dev_name(&rspi->ctlr->dev));
 	}
 	return ret;
 }
@@ -660,10 +660,10 @@ static bool __rspi_can_dma(const struct rspi_data *rspi,
 	return xfer->len > rspi->ops->fifo_size;
 }
 
-static bool rspi_can_dma(struct spi_master *master, struct spi_device *spi,
+static bool rspi_can_dma(struct spi_controller *ctlr, struct spi_device *spi,
 			 struct spi_transfer *xfer)
 {
-	struct rspi_data *rspi = spi_master_get_devdata(master);
+	struct rspi_data *rspi = spi_controller_get_devdata(ctlr);
 
 	return __rspi_can_dma(rspi, xfer);
 }
@@ -671,7 +671,7 @@ static bool rspi_can_dma(struct spi_master *master, struct spi_device *spi,
 static int rspi_dma_check_then_transfer(struct rspi_data *rspi,
 					 struct spi_transfer *xfer)
 {
-	if (!rspi->master->can_dma || !__rspi_can_dma(rspi, xfer))
+	if (!rspi->ctlr->can_dma || !__rspi_can_dma(rspi, xfer))
 		return -EAGAIN;
 
 	/* rx_buf can be NULL on RSPI on SH in TX-only Mode */
@@ -698,10 +698,10 @@ static int rspi_common_transfer(struct rspi_data *rspi,
 	return 0;
 }
 
-static int rspi_transfer_one(struct spi_master *master, struct spi_device *spi,
-			     struct spi_transfer *xfer)
+static int rspi_transfer_one(struct spi_controller *ctlr,
+			     struct spi_device *spi, struct spi_transfer *xfer)
 {
-	struct rspi_data *rspi = spi_master_get_devdata(master);
+	struct rspi_data *rspi = spi_controller_get_devdata(ctlr);
 	u8 spcr;
 
 	spcr = rspi_read8(rspi, RSPI_SPCR);
@@ -716,11 +716,11 @@ static int rspi_transfer_one(struct spi_master *master, struct spi_device *spi,
 	return rspi_common_transfer(rspi, xfer);
 }
 
-static int rspi_rz_transfer_one(struct spi_master *master,
+static int rspi_rz_transfer_one(struct spi_controller *ctlr,
 				struct spi_device *spi,
 				struct spi_transfer *xfer)
 {
-	struct rspi_data *rspi = spi_master_get_devdata(master);
+	struct rspi_data *rspi = spi_controller_get_devdata(ctlr);
 
 	rspi_rz_receive_init(rspi);
 
@@ -739,7 +739,7 @@ static int qspi_trigger_transfer_out_in(struct rspi_data *rspi, const u8 *tx,
 		if (n == QSPI_BUFFER_SIZE) {
 			ret = rspi_wait_for_tx_empty(rspi);
 			if (ret < 0) {
-				dev_err(&rspi->master->dev, "transmit timeout\n");
+				dev_err(&rspi->ctlr->dev, "transmit timeout\n");
 				return ret;
 			}
 			for (i = 0; i < n; i++)
@@ -747,7 +747,7 @@ static int qspi_trigger_transfer_out_in(struct rspi_data *rspi, const u8 *tx,
 
 			ret = rspi_wait_for_rx_full(rspi);
 			if (ret < 0) {
-				dev_err(&rspi->master->dev, "receive timeout\n");
+				dev_err(&rspi->ctlr->dev, "receive timeout\n");
 				return ret;
 			}
 			for (i = 0; i < n; i++)
@@ -785,7 +785,7 @@ static int qspi_transfer_out(struct rspi_data *rspi, struct spi_transfer *xfer)
 	unsigned int i, len;
 	int ret;
 
-	if (rspi->master->can_dma && __rspi_can_dma(rspi, xfer)) {
+	if (rspi->ctlr->can_dma && __rspi_can_dma(rspi, xfer)) {
 		ret = rspi_dma_transfer(rspi, &xfer->tx_sg, NULL);
 		if (ret != -EAGAIN)
 			return ret;
@@ -796,7 +796,7 @@ static int qspi_transfer_out(struct rspi_data *rspi, struct spi_transfer *xfer)
 		if (len == QSPI_BUFFER_SIZE) {
 			ret = rspi_wait_for_tx_empty(rspi);
 			if (ret < 0) {
-				dev_err(&rspi->master->dev, "transmit timeout\n");
+				dev_err(&rspi->ctlr->dev, "transmit timeout\n");
 				return ret;
 			}
 			for (i = 0; i < len; i++)
@@ -822,7 +822,7 @@ static int qspi_transfer_in(struct rspi_data *rspi, struct spi_transfer *xfer)
 	unsigned int i, len;
 	int ret;
 
-	if (rspi->master->can_dma && __rspi_can_dma(rspi, xfer)) {
+	if (rspi->ctlr->can_dma && __rspi_can_dma(rspi, xfer)) {
 		int ret = rspi_dma_transfer(rspi, NULL, &xfer->rx_sg);
 		if (ret != -EAGAIN)
 			return ret;
@@ -833,7 +833,7 @@ static int qspi_transfer_in(struct rspi_data *rspi, struct spi_transfer *xfer)
 		if (len == QSPI_BUFFER_SIZE) {
 			ret = rspi_wait_for_rx_full(rspi);
 			if (ret < 0) {
-				dev_err(&rspi->master->dev, "receive timeout\n");
+				dev_err(&rspi->ctlr->dev, "receive timeout\n");
 				return ret;
 			}
 			for (i = 0; i < len; i++)
@@ -849,10 +849,10 @@ static int qspi_transfer_in(struct rspi_data *rspi, struct spi_transfer *xfer)
 	return 0;
 }
 
-static int qspi_transfer_one(struct spi_master *master, struct spi_device *spi,
-			     struct spi_transfer *xfer)
+static int qspi_transfer_one(struct spi_controller *ctlr,
+			     struct spi_device *spi, struct spi_transfer *xfer)
 {
-	struct rspi_data *rspi = spi_master_get_devdata(master);
+	struct rspi_data *rspi = spi_controller_get_devdata(ctlr);
 
 	if (spi->mode & SPI_LOOP) {
 		return qspi_transfer_out_in(rspi, xfer);
@@ -870,7 +870,7 @@ static int qspi_transfer_one(struct spi_master *master, struct spi_device *spi,
 
 static int rspi_setup(struct spi_device *spi)
 {
-	struct rspi_data *rspi = spi_master_get_devdata(spi->master);
+	struct rspi_data *rspi = spi_controller_get_devdata(spi->controller);
 
 	rspi->max_speed_hz = spi->max_speed_hz;
 
@@ -955,10 +955,10 @@ static int qspi_setup_sequencer(struct rspi_data *rspi,
 	return 0;
 }
 
-static int rspi_prepare_message(struct spi_master *master,
+static int rspi_prepare_message(struct spi_controller *ctlr,
 				struct spi_message *msg)
 {
-	struct rspi_data *rspi = spi_master_get_devdata(master);
+	struct rspi_data *rspi = spi_controller_get_devdata(ctlr);
 	int ret;
 
 	if (msg->spi->mode &
@@ -974,10 +974,10 @@ static int rspi_prepare_message(struct spi_master *master,
 	return 0;
 }
 
-static int rspi_unprepare_message(struct spi_master *master,
+static int rspi_unprepare_message(struct spi_controller *ctlr,
 				  struct spi_message *msg)
 {
-	struct rspi_data *rspi = spi_master_get_devdata(master);
+	struct rspi_data *rspi = spi_controller_get_devdata(ctlr);
 
 	/* Disable SPI function */
 	rspi_write8(rspi, rspi_read8(rspi, RSPI_SPCR) & ~SPCR_SPE, RSPI_SPCR);
@@ -1081,7 +1081,7 @@ static struct dma_chan *rspi_request_dma_chan(struct device *dev,
 	return chan;
 }
 
-static int rspi_request_dma(struct device *dev, struct spi_master *master,
+static int rspi_request_dma(struct device *dev, struct spi_controller *ctlr,
 			    const struct resource *res)
 {
 	const struct rspi_plat_data *rspi_pd = dev_get_platdata(dev);
@@ -1099,37 +1099,37 @@ static int rspi_request_dma(struct device *dev, struct spi_master *master,
 		return 0;
 	}
 
-	master->dma_tx = rspi_request_dma_chan(dev, DMA_MEM_TO_DEV, dma_tx_id,
-					       res->start + RSPI_SPDR);
-	if (!master->dma_tx)
+	ctlr->dma_tx = rspi_request_dma_chan(dev, DMA_MEM_TO_DEV, dma_tx_id,
+					     res->start + RSPI_SPDR);
+	if (!ctlr->dma_tx)
 		return -ENODEV;
 
-	master->dma_rx = rspi_request_dma_chan(dev, DMA_DEV_TO_MEM, dma_rx_id,
-					       res->start + RSPI_SPDR);
-	if (!master->dma_rx) {
-		dma_release_channel(master->dma_tx);
-		master->dma_tx = NULL;
+	ctlr->dma_rx = rspi_request_dma_chan(dev, DMA_DEV_TO_MEM, dma_rx_id,
+					     res->start + RSPI_SPDR);
+	if (!ctlr->dma_rx) {
+		dma_release_channel(ctlr->dma_tx);
+		ctlr->dma_tx = NULL;
 		return -ENODEV;
 	}
 
-	master->can_dma = rspi_can_dma;
+	ctlr->can_dma = rspi_can_dma;
 	dev_info(dev, "DMA available");
 	return 0;
 }
 
-static void rspi_release_dma(struct spi_master *master)
+static void rspi_release_dma(struct spi_controller *ctlr)
 {
-	if (master->dma_tx)
-		dma_release_channel(master->dma_tx);
-	if (master->dma_rx)
-		dma_release_channel(master->dma_rx);
+	if (ctlr->dma_tx)
+		dma_release_channel(ctlr->dma_tx);
+	if (ctlr->dma_rx)
+		dma_release_channel(ctlr->dma_rx);
 }
 
 static int rspi_remove(struct platform_device *pdev)
 {
 	struct rspi_data *rspi = platform_get_drvdata(pdev);
 
-	rspi_release_dma(rspi->master);
+	rspi_release_dma(rspi->ctlr);
 	pm_runtime_disable(&pdev->dev);
 
 	return 0;
@@ -1139,7 +1139,7 @@ static const struct spi_ops rspi_ops = {
 	.set_config_register =	rspi_set_config_register,
 	.transfer_one =		rspi_transfer_one,
 	.mode_bits =		SPI_CPHA | SPI_CPOL | SPI_LOOP,
-	.flags =		SPI_MASTER_MUST_TX,
+	.flags =		SPI_CONTROLLER_MUST_TX,
 	.fifo_size =		8,
 };
 
@@ -1147,7 +1147,7 @@ static const struct spi_ops rspi_rz_ops = {
 	.set_config_register =	rspi_rz_set_config_register,
 	.transfer_one =		rspi_rz_transfer_one,
 	.mode_bits =		SPI_CPHA | SPI_CPOL | SPI_LOOP,
-	.flags =		SPI_MASTER_MUST_RX | SPI_MASTER_MUST_TX,
+	.flags =		SPI_CONTROLLER_MUST_RX | SPI_CONTROLLER_MUST_TX,
 	.fifo_size =		8,	/* 8 for TX, 32 for RX */
 };
 
@@ -1157,7 +1157,7 @@ static const struct spi_ops qspi_ops = {
 	.mode_bits =		SPI_CPHA | SPI_CPOL | SPI_LOOP |
 				SPI_TX_DUAL | SPI_TX_QUAD |
 				SPI_RX_DUAL | SPI_RX_QUAD,
-	.flags =		SPI_MASTER_MUST_RX | SPI_MASTER_MUST_TX,
+	.flags =		SPI_CONTROLLER_MUST_RX | SPI_CONTROLLER_MUST_TX,
 	.fifo_size =		32,
 };
 
@@ -1174,7 +1174,7 @@ static const struct of_device_id rspi_of_match[] = {
 
 MODULE_DEVICE_TABLE(of, rspi_of_match);
 
-static int rspi_parse_dt(struct device *dev, struct spi_master *master)
+static int rspi_parse_dt(struct device *dev, struct spi_controller *ctlr)
 {
 	u32 num_cs;
 	int error;
@@ -1186,12 +1186,12 @@ static int rspi_parse_dt(struct device *dev, struct spi_master *master)
 		return error;
 	}
 
-	master->num_chipselect = num_cs;
+	ctlr->num_chipselect = num_cs;
 	return 0;
 }
 #else
 #define rspi_of_match	NULL
-static inline int rspi_parse_dt(struct device *dev, struct spi_master *master)
+static inline int rspi_parse_dt(struct device *dev, struct spi_controller *ctlr)
 {
 	return -EINVAL;
 }
@@ -1212,28 +1212,28 @@ static int rspi_request_irq(struct device *dev, unsigned int irq,
 static int rspi_probe(struct platform_device *pdev)
 {
 	struct resource *res;
-	struct spi_master *master;
+	struct spi_controller *ctlr;
 	struct rspi_data *rspi;
 	int ret;
 	const struct rspi_plat_data *rspi_pd;
 	const struct spi_ops *ops;
 
-	master = spi_alloc_master(&pdev->dev, sizeof(struct rspi_data));
-	if (master == NULL)
+	ctlr = spi_alloc_master(&pdev->dev, sizeof(struct rspi_data));
+	if (ctlr == NULL)
 		return -ENOMEM;
 
 	ops = of_device_get_match_data(&pdev->dev);
 	if (ops) {
-		ret = rspi_parse_dt(&pdev->dev, master);
+		ret = rspi_parse_dt(&pdev->dev, ctlr);
 		if (ret)
 			goto error1;
 	} else {
 		ops = (struct spi_ops *)pdev->id_entry->driver_data;
 		rspi_pd = dev_get_platdata(&pdev->dev);
 		if (rspi_pd && rspi_pd->num_chipselect)
-			master->num_chipselect = rspi_pd->num_chipselect;
+			ctlr->num_chipselect = rspi_pd->num_chipselect;
 		else
-			master->num_chipselect = 2; /* default */
+			ctlr->num_chipselect = 2; /* default */
 	}
 
 	/* ops parameter check */
@@ -1243,10 +1243,10 @@ static int rspi_probe(struct platform_device *pdev)
 		goto error1;
 	}
 
-	rspi = spi_master_get_devdata(master);
+	rspi = spi_controller_get_devdata(ctlr);
 	platform_set_drvdata(pdev, rspi);
 	rspi->ops = ops;
-	rspi->master = master;
+	rspi->ctlr = ctlr;
 
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	rspi->addr = devm_ioremap_resource(&pdev->dev, res);
@@ -1266,15 +1266,15 @@ static int rspi_probe(struct platform_device *pdev)
 
 	init_waitqueue_head(&rspi->wait);
 
-	master->bus_num = pdev->id;
-	master->setup = rspi_setup;
-	master->auto_runtime_pm = true;
-	master->transfer_one = ops->transfer_one;
-	master->prepare_message = rspi_prepare_message;
-	master->unprepare_message = rspi_unprepare_message;
-	master->mode_bits = ops->mode_bits;
-	master->flags = ops->flags;
-	master->dev.of_node = pdev->dev.of_node;
+	ctlr->bus_num = pdev->id;
+	ctlr->setup = rspi_setup;
+	ctlr->auto_runtime_pm = true;
+	ctlr->transfer_one = ops->transfer_one;
+	ctlr->prepare_message = rspi_prepare_message;
+	ctlr->unprepare_message = rspi_unprepare_message;
+	ctlr->mode_bits = ops->mode_bits;
+	ctlr->flags = ops->flags;
+	ctlr->dev.of_node = pdev->dev.of_node;
 
 	ret = platform_get_irq_byname(pdev, "rx");
 	if (ret < 0) {
@@ -1311,13 +1311,13 @@ static int rspi_probe(struct platform_device *pdev)
 		goto error2;
 	}
 
-	ret = rspi_request_dma(&pdev->dev, master, res);
+	ret = rspi_request_dma(&pdev->dev, ctlr, res);
 	if (ret < 0)
 		dev_warn(&pdev->dev, "DMA not available, using PIO\n");
 
-	ret = devm_spi_register_master(&pdev->dev, master);
+	ret = devm_spi_register_controller(&pdev->dev, ctlr);
 	if (ret < 0) {
-		dev_err(&pdev->dev, "spi_register_master error.\n");
+		dev_err(&pdev->dev, "devm_spi_register_controller error.\n");
 		goto error3;
 	}
 
@@ -1326,11 +1326,11 @@ static int rspi_probe(struct platform_device *pdev)
 	return 0;
 
 error3:
-	rspi_release_dma(master);
+	rspi_release_dma(ctlr);
 error2:
 	pm_runtime_disable(&pdev->dev);
 error1:
-	spi_master_put(master);
+	spi_controller_put(ctlr);
 
 	return ret;
 }
@@ -1349,14 +1349,14 @@ static int rspi_suspend(struct device *dev)
 {
 	struct rspi_data *rspi = dev_get_drvdata(dev);
 
-	return spi_master_suspend(rspi->master);
+	return spi_controller_suspend(rspi->ctlr);
 }
 
 static int rspi_resume(struct device *dev)
 {
 	struct rspi_data *rspi = dev_get_drvdata(dev);
 
-	return spi_master_resume(rspi->master);
+	return spi_controller_resume(rspi->ctlr);
 }
 
 static SIMPLE_DEV_PM_OPS(rspi_pm_ops, rspi_suspend, rspi_resume);
diff --git a/drivers/spi/spi-sh-hspi.c b/drivers/spi/spi-sh-hspi.c
index dc0926e43665..7f73f91d412a 100644
--- a/drivers/spi/spi-sh-hspi.c
+++ b/drivers/spi/spi-sh-hspi.c
@@ -35,7 +35,7 @@
 
 struct hspi_priv {
 	void __iomem *addr;
-	struct spi_master *master;
+	struct spi_controller *ctlr;
 	struct device *dev;
 	struct clk *clk;
 };
@@ -140,10 +140,10 @@ static void hspi_hw_setup(struct hspi_priv *hspi,
 	hspi_write(hspi, SPSCR, 0x21);	/* master mode / CS control */
 }
 
-static int hspi_transfer_one_message(struct spi_master *master,
+static int hspi_transfer_one_message(struct spi_controller *ctlr,
 				     struct spi_message *msg)
 {
-	struct hspi_priv *hspi = spi_master_get_devdata(master);
+	struct hspi_priv *hspi = spi_controller_get_devdata(ctlr);
 	struct spi_transfer *t;
 	u32 tx;
 	u32 rx;
@@ -205,7 +205,7 @@ static int hspi_transfer_one_message(struct spi_master *master,
 		ndelay(nsecs);
 		hspi_hw_cs_disable(hspi);
 	}
-	spi_finalize_current_message(master);
+	spi_finalize_current_message(ctlr);
 
 	return ret;
 }
@@ -213,7 +213,7 @@ static int hspi_transfer_one_message(struct spi_master *master,
 static int hspi_probe(struct platform_device *pdev)
 {
 	struct resource *res;
-	struct spi_master *master;
+	struct spi_controller *ctlr;
 	struct hspi_priv *hspi;
 	struct clk *clk;
 	int ret;
@@ -225,11 +225,9 @@ static int hspi_probe(struct platform_device *pdev)
 		return -EINVAL;
 	}
 
-	master = spi_alloc_master(&pdev->dev, sizeof(*hspi));
-	if (!master) {
-		dev_err(&pdev->dev, "spi_alloc_master error.\n");
+	ctlr = spi_alloc_master(&pdev->dev, sizeof(*hspi));
+	if (!ctlr)
 		return -ENOMEM;
-	}
 
 	clk = clk_get(&pdev->dev, NULL);
 	if (IS_ERR(clk)) {
@@ -238,33 +236,32 @@ static int hspi_probe(struct platform_device *pdev)
 		goto error0;
 	}
 
-	hspi = spi_master_get_devdata(master);
+	hspi = spi_controller_get_devdata(ctlr);
 	platform_set_drvdata(pdev, hspi);
 
 	/* init hspi */
-	hspi->master	= master;
+	hspi->ctlr	= ctlr;
 	hspi->dev	= &pdev->dev;
 	hspi->clk	= clk;
 	hspi->addr	= devm_ioremap(hspi->dev,
 				       res->start, resource_size(res));
 	if (!hspi->addr) {
-		dev_err(&pdev->dev, "ioremap error.\n");
 		ret = -ENOMEM;
 		goto error1;
 	}
 
 	pm_runtime_enable(&pdev->dev);
 
-	master->bus_num		= pdev->id;
-	master->mode_bits	= SPI_CPOL | SPI_CPHA;
-	master->dev.of_node	= pdev->dev.of_node;
-	master->auto_runtime_pm = true;
-	master->transfer_one_message		= hspi_transfer_one_message;
-	master->bits_per_word_mask = SPI_BPW_MASK(8);
+	ctlr->bus_num = pdev->id;
+	ctlr->mode_bits	= SPI_CPOL | SPI_CPHA;
+	ctlr->dev.of_node = pdev->dev.of_node;
+	ctlr->auto_runtime_pm = true;
+	ctlr->transfer_one_message = hspi_transfer_one_message;
+	ctlr->bits_per_word_mask = SPI_BPW_MASK(8);
 
-	ret = devm_spi_register_master(&pdev->dev, master);
+	ret = devm_spi_register_controller(&pdev->dev, ctlr);
 	if (ret < 0) {
-		dev_err(&pdev->dev, "spi_register_master error.\n");
+		dev_err(&pdev->dev, "devm_spi_register_controller error.\n");
 		goto error2;
 	}
 
@@ -275,7 +272,7 @@ static int hspi_probe(struct platform_device *pdev)
  error1:
 	clk_put(clk);
  error0:
-	spi_master_put(master);
+	spi_controller_put(ctlr);
 
 	return ret;
 }
diff --git a/drivers/spi/spi-sh-msiof.c b/drivers/spi/spi-sh-msiof.c
index d14b407cc800..e2eb466db10a 100644
--- a/drivers/spi/spi-sh-msiof.c
+++ b/drivers/spi/spi-sh-msiof.c
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0
 /*
- * SuperH MSIOF SPI Master Interface
+ * SuperH MSIOF SPI Controller Interface
  *
  * Copyright (c) 2009 Magnus Damm
  * Copyright (C) 2014 Renesas Electronics Corporation
@@ -32,14 +32,15 @@
 #include <asm/unaligned.h>
 
 struct sh_msiof_chipdata {
+	u32 bits_per_word_mask;
 	u16 tx_fifo_size;
 	u16 rx_fifo_size;
-	u16 master_flags;
+	u16 ctlr_flags;
 	u16 min_div_pow;
 };
 
 struct sh_msiof_spi_priv {
-	struct spi_master *master;
+	struct spi_controller *ctlr;
 	void __iomem *mapbase;
 	struct clk *clk;
 	struct platform_device *pdev;
@@ -287,7 +288,7 @@ static void sh_msiof_spi_set_clk_regs(struct sh_msiof_spi_priv *p,
 
 	scr = sh_msiof_spi_div_array[div_pow] | SCR_BRPS(brps);
 	sh_msiof_write(p, TSCR, scr);
-	if (!(p->master->flags & SPI_MASTER_MUST_TX))
+	if (!(p->ctlr->flags & SPI_CONTROLLER_MUST_TX))
 		sh_msiof_write(p, RSCR, scr);
 }
 
@@ -351,14 +352,14 @@ static void sh_msiof_spi_set_pin_regs(struct sh_msiof_spi_priv *p, u32 ss,
 	tmp |= !cs_high << MDR1_SYNCAC_SHIFT;
 	tmp |= lsb_first << MDR1_BITLSB_SHIFT;
 	tmp |= sh_msiof_spi_get_dtdl_and_syncdl(p);
-	if (spi_controller_is_slave(p->master)) {
+	if (spi_controller_is_slave(p->ctlr)) {
 		sh_msiof_write(p, TMDR1, tmp | TMDR1_PCON);
 	} else {
 		sh_msiof_write(p, TMDR1,
 			       tmp | MDR1_TRMD | TMDR1_PCON |
 			       (ss < MAX_SS ? ss : 0) << TMDR1_SYNCCH_SHIFT);
 	}
-	if (p->master->flags & SPI_MASTER_MUST_TX) {
+	if (p->ctlr->flags & SPI_CONTROLLER_MUST_TX) {
 		/* These bits are reserved if RX needs TX */
 		tmp &= ~0x0000ffff;
 	}
@@ -382,7 +383,7 @@ static void sh_msiof_spi_set_mode_regs(struct sh_msiof_spi_priv *p,
 {
 	u32 dr2 = MDR2_BITLEN1(bits) | MDR2_WDLEN1(words);
 
-	if (tx_buf || (p->master->flags & SPI_MASTER_MUST_TX))
+	if (tx_buf || (p->ctlr->flags & SPI_CONTROLLER_MUST_TX))
 		sh_msiof_write(p, TMDR2, dr2);
 	else
 		sh_msiof_write(p, TMDR2, dr2 | MDR2_GRPMASK1);
@@ -539,8 +540,9 @@ static void sh_msiof_spi_read_fifo_s32u(struct sh_msiof_spi_priv *p,
 
 static int sh_msiof_spi_setup(struct spi_device *spi)
 {
-	struct device_node	*np = spi->master->dev.of_node;
-	struct sh_msiof_spi_priv *p = spi_master_get_devdata(spi->master);
+	struct device_node *np = spi->controller->dev.of_node;
+	struct sh_msiof_spi_priv *p =
+		spi_controller_get_devdata(spi->controller);
 	u32 clr, set, tmp;
 
 	if (!np) {
@@ -556,7 +558,7 @@ static int sh_msiof_spi_setup(struct spi_device *spi)
 		return 0;
 	}
 
-	if (spi_controller_is_slave(p->master))
+	if (spi_controller_is_slave(p->ctlr))
 		return 0;
 
 	if (p->native_cs_inited &&
@@ -581,10 +583,10 @@ static int sh_msiof_spi_setup(struct spi_device *spi)
 	return 0;
 }
 
-static int sh_msiof_prepare_message(struct spi_master *master,
+static int sh_msiof_prepare_message(struct spi_controller *ctlr,
 				    struct spi_message *msg)
 {
-	struct sh_msiof_spi_priv *p = spi_master_get_devdata(master);
+	struct sh_msiof_spi_priv *p = spi_controller_get_devdata(ctlr);
 	const struct spi_device *spi = msg->spi;
 	u32 ss, cs_high;
 
@@ -605,7 +607,7 @@ static int sh_msiof_prepare_message(struct spi_master *master,
 
 static int sh_msiof_spi_start(struct sh_msiof_spi_priv *p, void *rx_buf)
 {
-	bool slave = spi_controller_is_slave(p->master);
+	bool slave = spi_controller_is_slave(p->ctlr);
 	int ret = 0;
 
 	/* setup clock and rx/tx signals */
@@ -625,7 +627,7 @@ static int sh_msiof_spi_start(struct sh_msiof_spi_priv *p, void *rx_buf)
 
 static int sh_msiof_spi_stop(struct sh_msiof_spi_priv *p, void *rx_buf)
 {
-	bool slave = spi_controller_is_slave(p->master);
+	bool slave = spi_controller_is_slave(p->ctlr);
 	int ret = 0;
 
 	/* shut down frame, rx/tx and clock signals */
@@ -641,9 +643,9 @@ static int sh_msiof_spi_stop(struct sh_msiof_spi_priv *p, void *rx_buf)
 	return ret;
 }
 
-static int sh_msiof_slave_abort(struct spi_master *master)
+static int sh_msiof_slave_abort(struct spi_controller *ctlr)
 {
-	struct sh_msiof_spi_priv *p = spi_master_get_devdata(master);
+	struct sh_msiof_spi_priv *p = spi_controller_get_devdata(ctlr);
 
 	p->slave_aborted = true;
 	complete(&p->done);
@@ -654,7 +656,7 @@ static int sh_msiof_slave_abort(struct spi_master *master)
 static int sh_msiof_wait_for_completion(struct sh_msiof_spi_priv *p,
 					struct completion *x)
 {
-	if (spi_controller_is_slave(p->master)) {
+	if (spi_controller_is_slave(p->ctlr)) {
 		if (wait_for_completion_interruptible(x) ||
 		    p->slave_aborted) {
 			dev_dbg(&p->pdev->dev, "interrupted\n");
@@ -754,7 +756,7 @@ static int sh_msiof_dma_once(struct sh_msiof_spi_priv *p, const void *tx,
 	/* First prepare and submit the DMA request(s), as this may fail */
 	if (rx) {
 		ier_bits |= IER_RDREQE | IER_RDMAE;
-		desc_rx = dmaengine_prep_slave_single(p->master->dma_rx,
+		desc_rx = dmaengine_prep_slave_single(p->ctlr->dma_rx,
 					p->rx_dma_addr, len, DMA_DEV_TO_MEM,
 					DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
 		if (!desc_rx)
@@ -769,9 +771,9 @@ static int sh_msiof_dma_once(struct sh_msiof_spi_priv *p, const void *tx,
 
 	if (tx) {
 		ier_bits |= IER_TDREQE | IER_TDMAE;
-		dma_sync_single_for_device(p->master->dma_tx->device->dev,
+		dma_sync_single_for_device(p->ctlr->dma_tx->device->dev,
 					   p->tx_dma_addr, len, DMA_TO_DEVICE);
-		desc_tx = dmaengine_prep_slave_single(p->master->dma_tx,
+		desc_tx = dmaengine_prep_slave_single(p->ctlr->dma_tx,
 					p->tx_dma_addr, len, DMA_MEM_TO_DEV,
 					DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
 		if (!desc_tx) {
@@ -803,9 +805,9 @@ static int sh_msiof_dma_once(struct sh_msiof_spi_priv *p, const void *tx,
 
 	/* Now start DMA */
 	if (rx)
-		dma_async_issue_pending(p->master->dma_rx);
+		dma_async_issue_pending(p->ctlr->dma_rx);
 	if (tx)
-		dma_async_issue_pending(p->master->dma_tx);
+		dma_async_issue_pending(p->ctlr->dma_tx);
 
 	ret = sh_msiof_spi_start(p, rx);
 	if (ret) {
@@ -845,9 +847,8 @@ static int sh_msiof_dma_once(struct sh_msiof_spi_priv *p, const void *tx,
 	}
 
 	if (rx)
-		dma_sync_single_for_cpu(p->master->dma_rx->device->dev,
-					p->rx_dma_addr, len,
-					DMA_FROM_DEVICE);
+		dma_sync_single_for_cpu(p->ctlr->dma_rx->device->dev,
+					p->rx_dma_addr, len, DMA_FROM_DEVICE);
 
 	return 0;
 
@@ -856,10 +857,10 @@ static int sh_msiof_dma_once(struct sh_msiof_spi_priv *p, const void *tx,
 	sh_msiof_spi_stop(p, rx);
 stop_dma:
 	if (tx)
-		dmaengine_terminate_all(p->master->dma_tx);
+		dmaengine_terminate_all(p->ctlr->dma_tx);
 no_dma_tx:
 	if (rx)
-		dmaengine_terminate_all(p->master->dma_rx);
+		dmaengine_terminate_all(p->ctlr->dma_rx);
 	sh_msiof_write(p, IER, 0);
 	return ret;
 }
@@ -907,11 +908,11 @@ static void copy_plain32(u32 *dst, const u32 *src, unsigned int words)
 	memcpy(dst, src, words * 4);
 }
 
-static int sh_msiof_transfer_one(struct spi_master *master,
+static int sh_msiof_transfer_one(struct spi_controller *ctlr,
 				 struct spi_device *spi,
 				 struct spi_transfer *t)
 {
-	struct sh_msiof_spi_priv *p = spi_master_get_devdata(master);
+	struct sh_msiof_spi_priv *p = spi_controller_get_devdata(ctlr);
 	void (*copy32)(u32 *, const u32 *, unsigned int);
 	void (*tx_fifo)(struct sh_msiof_spi_priv *, const void *, int, int);
 	void (*rx_fifo)(struct sh_msiof_spi_priv *, void *, int, int);
@@ -926,10 +927,10 @@ static int sh_msiof_transfer_one(struct spi_master *master,
 	int ret;
 
 	/* setup clocks (clock already enabled in chipselect()) */
-	if (!spi_controller_is_slave(p->master))
+	if (!spi_controller_is_slave(p->ctlr))
 		sh_msiof_spi_set_clk_regs(p, clk_get_rate(p->clk), t->speed_hz);
 
-	while (master->dma_tx && len > 15) {
+	while (ctlr->dma_tx && len > 15) {
 		/*
 		 *  DMA supports 32-bit words only, hence pack 8-bit and 16-bit
 		 *  words, with byte resp. word swapping.
@@ -937,17 +938,13 @@ static int sh_msiof_transfer_one(struct spi_master *master,
 		unsigned int l = 0;
 
 		if (tx_buf)
-			l = min(len, p->tx_fifo_size * 4);
+			l = min(round_down(len, 4), p->tx_fifo_size * 4);
 		if (rx_buf)
-			l = min(len, p->rx_fifo_size * 4);
+			l = min(round_down(len, 4), p->rx_fifo_size * 4);
 
 		if (bits <= 8) {
-			if (l & 3)
-				break;
 			copy32 = copy_bswap32;
 		} else if (bits <= 16) {
-			if (l & 3)
-				break;
 			copy32 = copy_wswap32;
 		} else {
 			copy32 = copy_plain32;
@@ -1052,23 +1049,28 @@ static int sh_msiof_transfer_one(struct spi_master *master,
 }
 
 static const struct sh_msiof_chipdata sh_data = {
+	.bits_per_word_mask = SPI_BPW_RANGE_MASK(8, 32),
 	.tx_fifo_size = 64,
 	.rx_fifo_size = 64,
-	.master_flags = 0,
+	.ctlr_flags = 0,
 	.min_div_pow = 0,
 };
 
 static const struct sh_msiof_chipdata rcar_gen2_data = {
+	.bits_per_word_mask = SPI_BPW_MASK(8) | SPI_BPW_MASK(16) |
+			      SPI_BPW_MASK(24) | SPI_BPW_MASK(32),
 	.tx_fifo_size = 64,
 	.rx_fifo_size = 64,
-	.master_flags = SPI_MASTER_MUST_TX,
+	.ctlr_flags = SPI_CONTROLLER_MUST_TX,
 	.min_div_pow = 0,
 };
 
 static const struct sh_msiof_chipdata rcar_gen3_data = {
+	.bits_per_word_mask = SPI_BPW_MASK(8) | SPI_BPW_MASK(16) |
+			      SPI_BPW_MASK(24) | SPI_BPW_MASK(32),
 	.tx_fifo_size = 64,
 	.rx_fifo_size = 64,
-	.master_flags = SPI_MASTER_MUST_TX,
+	.ctlr_flags = SPI_CONTROLLER_MUST_TX,
 	.min_div_pow = 1,
 };
 
@@ -1136,7 +1138,7 @@ static int sh_msiof_get_cs_gpios(struct sh_msiof_spi_priv *p)
 	if (ret <= 0)
 		return 0;
 
-	num_cs = max_t(unsigned int, ret, p->master->num_chipselect);
+	num_cs = max_t(unsigned int, ret, p->ctlr->num_chipselect);
 	for (i = 0; i < num_cs; i++) {
 		struct gpio_desc *gpiod;
 
@@ -1206,10 +1208,10 @@ static int sh_msiof_request_dma(struct sh_msiof_spi_priv *p)
 {
 	struct platform_device *pdev = p->pdev;
 	struct device *dev = &pdev->dev;
-	const struct sh_msiof_spi_info *info = dev_get_platdata(dev);
+	const struct sh_msiof_spi_info *info = p->info;
 	unsigned int dma_tx_id, dma_rx_id;
 	const struct resource *res;
-	struct spi_master *master;
+	struct spi_controller *ctlr;
 	struct device *tx_dev, *rx_dev;
 
 	if (dev->of_node) {
@@ -1229,17 +1231,15 @@ static int sh_msiof_request_dma(struct sh_msiof_spi_priv *p)
 	if (!res)
 		res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 
-	master = p->master;
-	master->dma_tx = sh_msiof_request_dma_chan(dev, DMA_MEM_TO_DEV,
-						   dma_tx_id,
-						   res->start + TFDR);
-	if (!master->dma_tx)
+	ctlr = p->ctlr;
+	ctlr->dma_tx = sh_msiof_request_dma_chan(dev, DMA_MEM_TO_DEV,
+						 dma_tx_id, res->start + TFDR);
+	if (!ctlr->dma_tx)
 		return -ENODEV;
 
-	master->dma_rx = sh_msiof_request_dma_chan(dev, DMA_DEV_TO_MEM,
-						   dma_rx_id,
-						   res->start + RFDR);
-	if (!master->dma_rx)
+	ctlr->dma_rx = sh_msiof_request_dma_chan(dev, DMA_DEV_TO_MEM,
+						 dma_rx_id, res->start + RFDR);
+	if (!ctlr->dma_rx)
 		goto free_tx_chan;
 
 	p->tx_dma_page = (void *)__get_free_page(GFP_KERNEL | GFP_DMA);
@@ -1250,13 +1250,13 @@ static int sh_msiof_request_dma(struct sh_msiof_spi_priv *p)
 	if (!p->rx_dma_page)
 		goto free_tx_page;
 
-	tx_dev = master->dma_tx->device->dev;
+	tx_dev = ctlr->dma_tx->device->dev;
 	p->tx_dma_addr = dma_map_single(tx_dev, p->tx_dma_page, PAGE_SIZE,
 					DMA_TO_DEVICE);
 	if (dma_mapping_error(tx_dev, p->tx_dma_addr))
 		goto free_rx_page;
 
-	rx_dev = master->dma_rx->device->dev;
+	rx_dev = ctlr->dma_rx->device->dev;
 	p->rx_dma_addr = dma_map_single(rx_dev, p->rx_dma_page, PAGE_SIZE,
 					DMA_FROM_DEVICE);
 	if (dma_mapping_error(rx_dev, p->rx_dma_addr))
@@ -1272,34 +1272,34 @@ static int sh_msiof_request_dma(struct sh_msiof_spi_priv *p)
 free_tx_page:
 	free_page((unsigned long)p->tx_dma_page);
 free_rx_chan:
-	dma_release_channel(master->dma_rx);
+	dma_release_channel(ctlr->dma_rx);
 free_tx_chan:
-	dma_release_channel(master->dma_tx);
-	master->dma_tx = NULL;
+	dma_release_channel(ctlr->dma_tx);
+	ctlr->dma_tx = NULL;
 	return -ENODEV;
 }
 
 static void sh_msiof_release_dma(struct sh_msiof_spi_priv *p)
 {
-	struct spi_master *master = p->master;
+	struct spi_controller *ctlr = p->ctlr;
 
-	if (!master->dma_tx)
+	if (!ctlr->dma_tx)
 		return;
 
-	dma_unmap_single(master->dma_rx->device->dev, p->rx_dma_addr,
-			 PAGE_SIZE, DMA_FROM_DEVICE);
-	dma_unmap_single(master->dma_tx->device->dev, p->tx_dma_addr,
-			 PAGE_SIZE, DMA_TO_DEVICE);
+	dma_unmap_single(ctlr->dma_rx->device->dev, p->rx_dma_addr, PAGE_SIZE,
+			 DMA_FROM_DEVICE);
+	dma_unmap_single(ctlr->dma_tx->device->dev, p->tx_dma_addr, PAGE_SIZE,
+			 DMA_TO_DEVICE);
 	free_page((unsigned long)p->rx_dma_page);
 	free_page((unsigned long)p->tx_dma_page);
-	dma_release_channel(master->dma_rx);
-	dma_release_channel(master->dma_tx);
+	dma_release_channel(ctlr->dma_rx);
+	dma_release_channel(ctlr->dma_tx);
 }
 
 static int sh_msiof_spi_probe(struct platform_device *pdev)
 {
 	struct resource	*r;
-	struct spi_master *master;
+	struct spi_controller *ctlr;
 	const struct sh_msiof_chipdata *chipdata;
 	struct sh_msiof_spi_info *info;
 	struct sh_msiof_spi_priv *p;
@@ -1320,18 +1320,18 @@ static int sh_msiof_spi_probe(struct platform_device *pdev)
 	}
 
 	if (info->mode == MSIOF_SPI_SLAVE)
-		master = spi_alloc_slave(&pdev->dev,
-					 sizeof(struct sh_msiof_spi_priv));
+		ctlr = spi_alloc_slave(&pdev->dev,
+				       sizeof(struct sh_msiof_spi_priv));
 	else
-		master = spi_alloc_master(&pdev->dev,
-					  sizeof(struct sh_msiof_spi_priv));
-	if (master == NULL)
+		ctlr = spi_alloc_master(&pdev->dev,
+					sizeof(struct sh_msiof_spi_priv));
+	if (ctlr == NULL)
 		return -ENOMEM;
 
-	p = spi_master_get_devdata(master);
+	p = spi_controller_get_devdata(ctlr);
 
 	platform_set_drvdata(pdev, p);
-	p->master = master;
+	p->ctlr = ctlr;
 	p->info = info;
 	p->min_div_pow = chipdata->min_div_pow;
 
@@ -1378,31 +1378,31 @@ static int sh_msiof_spi_probe(struct platform_device *pdev)
 		p->rx_fifo_size = p->info->rx_fifo_override;
 
 	/* Setup GPIO chip selects */
-	master->num_chipselect = p->info->num_chipselect;
+	ctlr->num_chipselect = p->info->num_chipselect;
 	ret = sh_msiof_get_cs_gpios(p);
 	if (ret)
 		goto err1;
 
-	/* init master code */
-	master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH;
-	master->mode_bits |= SPI_LSB_FIRST | SPI_3WIRE;
-	master->flags = chipdata->master_flags;
-	master->bus_num = pdev->id;
-	master->dev.of_node = pdev->dev.of_node;
-	master->setup = sh_msiof_spi_setup;
-	master->prepare_message = sh_msiof_prepare_message;
-	master->slave_abort = sh_msiof_slave_abort;
-	master->bits_per_word_mask = SPI_BPW_RANGE_MASK(8, 32);
-	master->auto_runtime_pm = true;
-	master->transfer_one = sh_msiof_transfer_one;
+	/* init controller code */
+	ctlr->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH;
+	ctlr->mode_bits |= SPI_LSB_FIRST | SPI_3WIRE;
+	ctlr->flags = chipdata->ctlr_flags;
+	ctlr->bus_num = pdev->id;
+	ctlr->dev.of_node = pdev->dev.of_node;
+	ctlr->setup = sh_msiof_spi_setup;
+	ctlr->prepare_message = sh_msiof_prepare_message;
+	ctlr->slave_abort = sh_msiof_slave_abort;
+	ctlr->bits_per_word_mask = chipdata->bits_per_word_mask;
+	ctlr->auto_runtime_pm = true;
+	ctlr->transfer_one = sh_msiof_transfer_one;
 
 	ret = sh_msiof_request_dma(p);
 	if (ret < 0)
 		dev_warn(&pdev->dev, "DMA not available, using PIO\n");
 
-	ret = devm_spi_register_master(&pdev->dev, master);
+	ret = devm_spi_register_controller(&pdev->dev, ctlr);
 	if (ret < 0) {
-		dev_err(&pdev->dev, "spi_register_master error.\n");
+		dev_err(&pdev->dev, "devm_spi_register_controller error.\n");
 		goto err2;
 	}
 
@@ -1412,7 +1412,7 @@ static int sh_msiof_spi_probe(struct platform_device *pdev)
 	sh_msiof_release_dma(p);
 	pm_runtime_disable(&pdev->dev);
  err1:
-	spi_master_put(master);
+	spi_controller_put(ctlr);
 	return ret;
 }
 
@@ -1436,14 +1436,14 @@ static int sh_msiof_spi_suspend(struct device *dev)
 {
 	struct sh_msiof_spi_priv *p = dev_get_drvdata(dev);
 
-	return spi_master_suspend(p->master);
+	return spi_controller_suspend(p->ctlr);
 }
 
 static int sh_msiof_spi_resume(struct device *dev)
 {
 	struct sh_msiof_spi_priv *p = dev_get_drvdata(dev);
 
-	return spi_master_resume(p->master);
+	return spi_controller_resume(p->ctlr);
 }
 
 static SIMPLE_DEV_PM_OPS(sh_msiof_spi_pm_ops, sh_msiof_spi_suspend,
@@ -1465,7 +1465,7 @@ static struct platform_driver sh_msiof_spi_drv = {
 };
 module_platform_driver(sh_msiof_spi_drv);
 
-MODULE_DESCRIPTION("SuperH MSIOF SPI Master Interface Driver");
+MODULE_DESCRIPTION("SuperH MSIOF SPI Controller Interface Driver");
 MODULE_AUTHOR("Magnus Damm");
 MODULE_LICENSE("GPL v2");
 MODULE_ALIAS("platform:spi_sh_msiof");
diff --git a/drivers/spi/spi-sifive.c b/drivers/spi/spi-sifive.c
new file mode 100644
index 000000000000..93ec2c6cdbfd
--- /dev/null
+++ b/drivers/spi/spi-sifive.c
@@ -0,0 +1,448 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// Copyright 2018 SiFive, Inc.
+//
+// SiFive SPI controller driver (master mode only)
+//
+// Author: SiFive, Inc.
+// sifive@sifive.com
+
+#include <linux/clk.h>
+#include <linux/module.h>
+#include <linux/interrupt.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/spi/spi.h>
+#include <linux/io.h>
+#include <linux/log2.h>
+
+#define SIFIVE_SPI_DRIVER_NAME           "sifive_spi"
+
+#define SIFIVE_SPI_MAX_CS                32
+#define SIFIVE_SPI_DEFAULT_DEPTH         8
+#define SIFIVE_SPI_DEFAULT_MAX_BITS      8
+
+/* register offsets */
+#define SIFIVE_SPI_REG_SCKDIV            0x00 /* Serial clock divisor */
+#define SIFIVE_SPI_REG_SCKMODE           0x04 /* Serial clock mode */
+#define SIFIVE_SPI_REG_CSID              0x10 /* Chip select ID */
+#define SIFIVE_SPI_REG_CSDEF             0x14 /* Chip select default */
+#define SIFIVE_SPI_REG_CSMODE            0x18 /* Chip select mode */
+#define SIFIVE_SPI_REG_DELAY0            0x28 /* Delay control 0 */
+#define SIFIVE_SPI_REG_DELAY1            0x2c /* Delay control 1 */
+#define SIFIVE_SPI_REG_FMT               0x40 /* Frame format */
+#define SIFIVE_SPI_REG_TXDATA            0x48 /* Tx FIFO data */
+#define SIFIVE_SPI_REG_RXDATA            0x4c /* Rx FIFO data */
+#define SIFIVE_SPI_REG_TXMARK            0x50 /* Tx FIFO watermark */
+#define SIFIVE_SPI_REG_RXMARK            0x54 /* Rx FIFO watermark */
+#define SIFIVE_SPI_REG_FCTRL             0x60 /* SPI flash interface control */
+#define SIFIVE_SPI_REG_FFMT              0x64 /* SPI flash instruction format */
+#define SIFIVE_SPI_REG_IE                0x70 /* Interrupt Enable Register */
+#define SIFIVE_SPI_REG_IP                0x74 /* Interrupt Pendings Register */
+
+/* sckdiv bits */
+#define SIFIVE_SPI_SCKDIV_DIV_MASK       0xfffU
+
+/* sckmode bits */
+#define SIFIVE_SPI_SCKMODE_PHA           BIT(0)
+#define SIFIVE_SPI_SCKMODE_POL           BIT(1)
+#define SIFIVE_SPI_SCKMODE_MODE_MASK     (SIFIVE_SPI_SCKMODE_PHA | \
+					  SIFIVE_SPI_SCKMODE_POL)
+
+/* csmode bits */
+#define SIFIVE_SPI_CSMODE_MODE_AUTO      0U
+#define SIFIVE_SPI_CSMODE_MODE_HOLD      2U
+#define SIFIVE_SPI_CSMODE_MODE_OFF       3U
+
+/* delay0 bits */
+#define SIFIVE_SPI_DELAY0_CSSCK(x)       ((u32)(x))
+#define SIFIVE_SPI_DELAY0_CSSCK_MASK     0xffU
+#define SIFIVE_SPI_DELAY0_SCKCS(x)       ((u32)(x) << 16)
+#define SIFIVE_SPI_DELAY0_SCKCS_MASK     (0xffU << 16)
+
+/* delay1 bits */
+#define SIFIVE_SPI_DELAY1_INTERCS(x)     ((u32)(x))
+#define SIFIVE_SPI_DELAY1_INTERCS_MASK   0xffU
+#define SIFIVE_SPI_DELAY1_INTERXFR(x)    ((u32)(x) << 16)
+#define SIFIVE_SPI_DELAY1_INTERXFR_MASK  (0xffU << 16)
+
+/* fmt bits */
+#define SIFIVE_SPI_FMT_PROTO_SINGLE      0U
+#define SIFIVE_SPI_FMT_PROTO_DUAL        1U
+#define SIFIVE_SPI_FMT_PROTO_QUAD        2U
+#define SIFIVE_SPI_FMT_PROTO_MASK        3U
+#define SIFIVE_SPI_FMT_ENDIAN            BIT(2)
+#define SIFIVE_SPI_FMT_DIR               BIT(3)
+#define SIFIVE_SPI_FMT_LEN(x)            ((u32)(x) << 16)
+#define SIFIVE_SPI_FMT_LEN_MASK          (0xfU << 16)
+
+/* txdata bits */
+#define SIFIVE_SPI_TXDATA_DATA_MASK      0xffU
+#define SIFIVE_SPI_TXDATA_FULL           BIT(31)
+
+/* rxdata bits */
+#define SIFIVE_SPI_RXDATA_DATA_MASK      0xffU
+#define SIFIVE_SPI_RXDATA_EMPTY          BIT(31)
+
+/* ie and ip bits */
+#define SIFIVE_SPI_IP_TXWM               BIT(0)
+#define SIFIVE_SPI_IP_RXWM               BIT(1)
+
+struct sifive_spi {
+	void __iomem      *regs;        /* virt. address of control registers */
+	struct clk        *clk;         /* bus clock */
+	unsigned int      fifo_depth;   /* fifo depth in words */
+	u32               cs_inactive;  /* level of the CS pins when inactive */
+	struct completion done;         /* wake-up from interrupt */
+};
+
+static void sifive_spi_write(struct sifive_spi *spi, int offset, u32 value)
+{
+	iowrite32(value, spi->regs + offset);
+}
+
+static u32 sifive_spi_read(struct sifive_spi *spi, int offset)
+{
+	return ioread32(spi->regs + offset);
+}
+
+static void sifive_spi_init(struct sifive_spi *spi)
+{
+	/* Watermark interrupts are disabled by default */
+	sifive_spi_write(spi, SIFIVE_SPI_REG_IE, 0);
+
+	/* Default watermark FIFO threshold values */
+	sifive_spi_write(spi, SIFIVE_SPI_REG_TXMARK, 1);
+	sifive_spi_write(spi, SIFIVE_SPI_REG_RXMARK, 0);
+
+	/* Set CS/SCK Delays and Inactive Time to defaults */
+	sifive_spi_write(spi, SIFIVE_SPI_REG_DELAY0,
+			 SIFIVE_SPI_DELAY0_CSSCK(1) |
+			 SIFIVE_SPI_DELAY0_SCKCS(1));
+	sifive_spi_write(spi, SIFIVE_SPI_REG_DELAY1,
+			 SIFIVE_SPI_DELAY1_INTERCS(1) |
+			 SIFIVE_SPI_DELAY1_INTERXFR(0));
+
+	/* Exit specialized memory-mapped SPI flash mode */
+	sifive_spi_write(spi, SIFIVE_SPI_REG_FCTRL, 0);
+}
+
+static int
+sifive_spi_prepare_message(struct spi_master *master, struct spi_message *msg)
+{
+	struct sifive_spi *spi = spi_master_get_devdata(master);
+	struct spi_device *device = msg->spi;
+
+	/* Update the chip select polarity */
+	if (device->mode & SPI_CS_HIGH)
+		spi->cs_inactive &= ~BIT(device->chip_select);
+	else
+		spi->cs_inactive |= BIT(device->chip_select);
+	sifive_spi_write(spi, SIFIVE_SPI_REG_CSDEF, spi->cs_inactive);
+
+	/* Select the correct device */
+	sifive_spi_write(spi, SIFIVE_SPI_REG_CSID, device->chip_select);
+
+	/* Set clock mode */
+	sifive_spi_write(spi, SIFIVE_SPI_REG_SCKMODE,
+			 device->mode & SIFIVE_SPI_SCKMODE_MODE_MASK);
+
+	return 0;
+}
+
+static void sifive_spi_set_cs(struct spi_device *device, bool is_high)
+{
+	struct sifive_spi *spi = spi_master_get_devdata(device->master);
+
+	/* Reverse polarity is handled by SCMR/CPOL. Not inverted CS. */
+	if (device->mode & SPI_CS_HIGH)
+		is_high = !is_high;
+
+	sifive_spi_write(spi, SIFIVE_SPI_REG_CSMODE, is_high ?
+			 SIFIVE_SPI_CSMODE_MODE_AUTO :
+			 SIFIVE_SPI_CSMODE_MODE_HOLD);
+}
+
+static int
+sifive_spi_prep_transfer(struct sifive_spi *spi, struct spi_device *device,
+			 struct spi_transfer *t)
+{
+	u32 cr;
+	unsigned int mode;
+
+	/* Calculate and program the clock rate */
+	cr = DIV_ROUND_UP(clk_get_rate(spi->clk) >> 1, t->speed_hz) - 1;
+	cr &= SIFIVE_SPI_SCKDIV_DIV_MASK;
+	sifive_spi_write(spi, SIFIVE_SPI_REG_SCKDIV, cr);
+
+	mode = max_t(unsigned int, t->rx_nbits, t->tx_nbits);
+
+	/* Set frame format */
+	cr = SIFIVE_SPI_FMT_LEN(t->bits_per_word);
+	switch (mode) {
+	case SPI_NBITS_QUAD:
+		cr |= SIFIVE_SPI_FMT_PROTO_QUAD;
+		break;
+	case SPI_NBITS_DUAL:
+		cr |= SIFIVE_SPI_FMT_PROTO_DUAL;
+		break;
+	default:
+		cr |= SIFIVE_SPI_FMT_PROTO_SINGLE;
+		break;
+	}
+	if (device->mode & SPI_LSB_FIRST)
+		cr |= SIFIVE_SPI_FMT_ENDIAN;
+	if (!t->rx_buf)
+		cr |= SIFIVE_SPI_FMT_DIR;
+	sifive_spi_write(spi, SIFIVE_SPI_REG_FMT, cr);
+
+	/* We will want to poll if the time we need to wait is
+	 * less than the context switching time.
+	 * Let's call that threshold 5us. The operation will take:
+	 *    (8/mode) * fifo_depth / hz <= 5 * 10^-6
+	 *    1600000 * fifo_depth <= hz * mode
+	 */
+	return 1600000 * spi->fifo_depth <= t->speed_hz * mode;
+}
+
+static irqreturn_t sifive_spi_irq(int irq, void *dev_id)
+{
+	struct sifive_spi *spi = dev_id;
+	u32 ip = sifive_spi_read(spi, SIFIVE_SPI_REG_IP);
+
+	if (ip & (SIFIVE_SPI_IP_TXWM | SIFIVE_SPI_IP_RXWM)) {
+		/* Disable interrupts until next transfer */
+		sifive_spi_write(spi, SIFIVE_SPI_REG_IE, 0);
+		complete(&spi->done);
+		return IRQ_HANDLED;
+	}
+
+	return IRQ_NONE;
+}
+
+static void sifive_spi_wait(struct sifive_spi *spi, u32 bit, int poll)
+{
+	if (poll) {
+		u32 cr;
+
+		do {
+			cr = sifive_spi_read(spi, SIFIVE_SPI_REG_IP);
+		} while (!(cr & bit));
+	} else {
+		reinit_completion(&spi->done);
+		sifive_spi_write(spi, SIFIVE_SPI_REG_IE, bit);
+		wait_for_completion(&spi->done);
+	}
+}
+
+static void sifive_spi_tx(struct sifive_spi *spi, const u8 *tx_ptr)
+{
+	WARN_ON_ONCE((sifive_spi_read(spi, SIFIVE_SPI_REG_TXDATA)
+				& SIFIVE_SPI_TXDATA_FULL) != 0);
+	sifive_spi_write(spi, SIFIVE_SPI_REG_TXDATA,
+			 *tx_ptr & SIFIVE_SPI_TXDATA_DATA_MASK);
+}
+
+static void sifive_spi_rx(struct sifive_spi *spi, u8 *rx_ptr)
+{
+	u32 data = sifive_spi_read(spi, SIFIVE_SPI_REG_RXDATA);
+
+	WARN_ON_ONCE((data & SIFIVE_SPI_RXDATA_EMPTY) != 0);
+	*rx_ptr = data & SIFIVE_SPI_RXDATA_DATA_MASK;
+}
+
+static int
+sifive_spi_transfer_one(struct spi_master *master, struct spi_device *device,
+			struct spi_transfer *t)
+{
+	struct sifive_spi *spi = spi_master_get_devdata(master);
+	int poll = sifive_spi_prep_transfer(spi, device, t);
+	const u8 *tx_ptr = t->tx_buf;
+	u8 *rx_ptr = t->rx_buf;
+	unsigned int remaining_words = t->len;
+
+	while (remaining_words) {
+		unsigned int n_words = min(remaining_words, spi->fifo_depth);
+		unsigned int i;
+
+		/* Enqueue n_words for transmission */
+		for (i = 0; i < n_words; i++)
+			sifive_spi_tx(spi, tx_ptr++);
+
+		if (rx_ptr) {
+			/* Wait for transmission + reception to complete */
+			sifive_spi_write(spi, SIFIVE_SPI_REG_RXMARK,
+					 n_words - 1);
+			sifive_spi_wait(spi, SIFIVE_SPI_IP_RXWM, poll);
+
+			/* Read out all the data from the RX FIFO */
+			for (i = 0; i < n_words; i++)
+				sifive_spi_rx(spi, rx_ptr++);
+		} else {
+			/* Wait for transmission to complete */
+			sifive_spi_wait(spi, SIFIVE_SPI_IP_TXWM, poll);
+		}
+
+		remaining_words -= n_words;
+	}
+
+	return 0;
+}
+
+static int sifive_spi_probe(struct platform_device *pdev)
+{
+	struct sifive_spi *spi;
+	struct resource *res;
+	int ret, irq, num_cs;
+	u32 cs_bits, max_bits_per_word;
+	struct spi_master *master;
+
+	master = spi_alloc_master(&pdev->dev, sizeof(struct sifive_spi));
+	if (!master) {
+		dev_err(&pdev->dev, "out of memory\n");
+		return -ENOMEM;
+	}
+
+	spi = spi_master_get_devdata(master);
+	init_completion(&spi->done);
+	platform_set_drvdata(pdev, master);
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	spi->regs = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(spi->regs)) {
+		ret = PTR_ERR(spi->regs);
+		goto put_master;
+	}
+
+	spi->clk = devm_clk_get(&pdev->dev, NULL);
+	if (IS_ERR(spi->clk)) {
+		dev_err(&pdev->dev, "Unable to find bus clock\n");
+		ret = PTR_ERR(spi->clk);
+		goto put_master;
+	}
+
+	irq = platform_get_irq(pdev, 0);
+	if (irq < 0) {
+		dev_err(&pdev->dev, "Unable to find interrupt\n");
+		ret = irq;
+		goto put_master;
+	}
+
+	/* Optional parameters */
+	ret =
+	  of_property_read_u32(pdev->dev.of_node, "sifive,fifo-depth",
+			       &spi->fifo_depth);
+	if (ret < 0)
+		spi->fifo_depth = SIFIVE_SPI_DEFAULT_DEPTH;
+
+	ret =
+	  of_property_read_u32(pdev->dev.of_node, "sifive,max-bits-per-word",
+			       &max_bits_per_word);
+
+	if (!ret && max_bits_per_word < 8) {
+		dev_err(&pdev->dev, "Only 8bit SPI words supported by the driver\n");
+		ret = -EINVAL;
+		goto put_master;
+	}
+
+	/* Spin up the bus clock before hitting registers */
+	ret = clk_prepare_enable(spi->clk);
+	if (ret) {
+		dev_err(&pdev->dev, "Unable to enable bus clock\n");
+		goto put_master;
+	}
+
+	/* probe the number of CS lines */
+	spi->cs_inactive = sifive_spi_read(spi, SIFIVE_SPI_REG_CSDEF);
+	sifive_spi_write(spi, SIFIVE_SPI_REG_CSDEF, 0xffffffffU);
+	cs_bits = sifive_spi_read(spi, SIFIVE_SPI_REG_CSDEF);
+	sifive_spi_write(spi, SIFIVE_SPI_REG_CSDEF, spi->cs_inactive);
+	if (!cs_bits) {
+		dev_err(&pdev->dev, "Could not auto probe CS lines\n");
+		ret = -EINVAL;
+		goto put_master;
+	}
+
+	num_cs = ilog2(cs_bits) + 1;
+	if (num_cs > SIFIVE_SPI_MAX_CS) {
+		dev_err(&pdev->dev, "Invalid number of spi slaves\n");
+		ret = -EINVAL;
+		goto put_master;
+	}
+
+	/* Define our master */
+	master->dev.of_node = pdev->dev.of_node;
+	master->bus_num = pdev->id;
+	master->num_chipselect = num_cs;
+	master->mode_bits = SPI_CPHA | SPI_CPOL
+			  | SPI_CS_HIGH | SPI_LSB_FIRST
+			  | SPI_TX_DUAL | SPI_TX_QUAD
+			  | SPI_RX_DUAL | SPI_RX_QUAD;
+	/* TODO: add driver support for bits_per_word < 8
+	 * we need to "left-align" the bits (unless SPI_LSB_FIRST)
+	 */
+	master->bits_per_word_mask = SPI_BPW_MASK(8);
+	master->flags = SPI_CONTROLLER_MUST_TX | SPI_MASTER_GPIO_SS;
+	master->prepare_message = sifive_spi_prepare_message;
+	master->set_cs = sifive_spi_set_cs;
+	master->transfer_one = sifive_spi_transfer_one;
+
+	pdev->dev.dma_mask = NULL;
+	/* Configure the SPI master hardware */
+	sifive_spi_init(spi);
+
+	/* Register for SPI Interrupt */
+	ret = devm_request_irq(&pdev->dev, irq, sifive_spi_irq, 0,
+			       dev_name(&pdev->dev), spi);
+	if (ret) {
+		dev_err(&pdev->dev, "Unable to bind to interrupt\n");
+		goto put_master;
+	}
+
+	dev_info(&pdev->dev, "mapped; irq=%d, cs=%d\n",
+		 irq, master->num_chipselect);
+
+	ret = devm_spi_register_master(&pdev->dev, master);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "spi_register_master failed\n");
+		goto put_master;
+	}
+
+	return 0;
+
+put_master:
+	spi_master_put(master);
+
+	return ret;
+}
+
+static int sifive_spi_remove(struct platform_device *pdev)
+{
+	struct spi_master *master = platform_get_drvdata(pdev);
+	struct sifive_spi *spi = spi_master_get_devdata(master);
+
+	/* Disable all the interrupts just in case */
+	sifive_spi_write(spi, SIFIVE_SPI_REG_IE, 0);
+
+	return 0;
+}
+
+static const struct of_device_id sifive_spi_of_match[] = {
+	{ .compatible = "sifive,spi0", },
+	{}
+};
+MODULE_DEVICE_TABLE(of, sifive_spi_of_match);
+
+static struct platform_driver sifive_spi_driver = {
+	.probe = sifive_spi_probe,
+	.remove = sifive_spi_remove,
+	.driver = {
+		.name = SIFIVE_SPI_DRIVER_NAME,
+		.of_match_table = sifive_spi_of_match,
+	},
+};
+module_platform_driver(sifive_spi_driver);
+
+MODULE_AUTHOR("SiFive, Inc. <sifive@sifive.com>");
+MODULE_DESCRIPTION("SiFive SPI driver");
+MODULE_LICENSE("GPL");
diff --git a/drivers/spi/spi-sprd.c b/drivers/spi/spi-sprd.c
index 8daa24eec624..1b7eebb72c07 100644
--- a/drivers/spi/spi-sprd.c
+++ b/drivers/spi/spi-sprd.c
@@ -2,6 +2,9 @@
 // Copyright (C) 2018 Spreadtrum Communications Inc.
 
 #include <linux/clk.h>
+#include <linux/dmaengine.h>
+#include <linux/dma-mapping.h>
+#include <linux/dma/sprd-dma.h>
 #include <linux/interrupt.h>
 #include <linux/io.h>
 #include <linux/iopoll.h>
@@ -9,6 +12,7 @@
 #include <linux/module.h>
 #include <linux/of.h>
 #include <linux/of_device.h>
+#include <linux/of_dma.h>
 #include <linux/platform_device.h>
 #include <linux/pm_runtime.h>
 #include <linux/spi/spi.h>
@@ -128,11 +132,28 @@
 #define SPRD_SPI_DEFAULT_SOURCE		26000000
 #define SPRD_SPI_MAX_SPEED_HZ		48000000
 #define SPRD_SPI_AUTOSUSPEND_DELAY	100
+#define SPRD_SPI_DMA_STEP		8
+
+enum sprd_spi_dma_channel {
+	SPRD_SPI_RX,
+	SPRD_SPI_TX,
+	SPRD_SPI_MAX,
+};
+
+struct sprd_spi_dma {
+	bool enable;
+	struct dma_chan *dma_chan[SPRD_SPI_MAX];
+	enum dma_slave_buswidth width;
+	u32 fragmens_len;
+	u32 rx_len;
+};
 
 struct sprd_spi {
 	void __iomem *base;
+	phys_addr_t phy_base;
 	struct device *dev;
 	struct clk *clk;
+	int irq;
 	u32 src_clk;
 	u32 hw_mode;
 	u32 trans_len;
@@ -141,6 +162,8 @@ struct sprd_spi {
 	u32 hw_speed_hz;
 	u32 len;
 	int status;
+	struct sprd_spi_dma dma;
+	struct completion xfer_completion;
 	const void *tx_buf;
 	void *rx_buf;
 	int (*read_bufs)(struct sprd_spi *ss, u32 len);
@@ -380,7 +403,7 @@ static int sprd_spi_txrx_bufs(struct spi_device *sdev, struct spi_transfer *t)
 {
 	struct sprd_spi *ss = spi_controller_get_devdata(sdev->controller);
 	u32 trans_len = ss->trans_len, len;
-	int ret, write_size = 0;
+	int ret, write_size = 0, read_size = 0;
 
 	while (trans_len) {
 		len = trans_len > SPRD_SPI_FIFO_SIZE ? SPRD_SPI_FIFO_SIZE :
@@ -416,19 +439,223 @@ static int sprd_spi_txrx_bufs(struct spi_device *sdev, struct spi_transfer *t)
 			goto complete;
 
 		if (ss->trans_mode & SPRD_SPI_RX_MODE)
-			ss->read_bufs(ss, len);
+			read_size += ss->read_bufs(ss, len);
 
 		trans_len -= len;
 	}
 
-	ret = write_size;
-
+	if (ss->trans_mode & SPRD_SPI_TX_MODE)
+		ret = write_size;
+	else
+		ret = read_size;
 complete:
 	sprd_spi_enter_idle(ss);
 
 	return ret;
 }
 
+static void sprd_spi_irq_enable(struct sprd_spi *ss)
+{
+	u32 val;
+
+	/* Clear interrupt status before enabling interrupt. */
+	writel_relaxed(SPRD_SPI_TX_END_CLR | SPRD_SPI_RX_END_CLR,
+		ss->base + SPRD_SPI_INT_CLR);
+	/* Enable SPI interrupt only in DMA mode. */
+	val = readl_relaxed(ss->base + SPRD_SPI_INT_EN);
+	writel_relaxed(val | SPRD_SPI_TX_END_INT_EN |
+		       SPRD_SPI_RX_END_INT_EN,
+		       ss->base + SPRD_SPI_INT_EN);
+}
+
+static void sprd_spi_irq_disable(struct sprd_spi *ss)
+{
+	writel_relaxed(0, ss->base + SPRD_SPI_INT_EN);
+}
+
+static void sprd_spi_dma_enable(struct sprd_spi *ss, bool enable)
+{
+	u32 val = readl_relaxed(ss->base + SPRD_SPI_CTL2);
+
+	if (enable)
+		val |= SPRD_SPI_DMA_EN;
+	else
+		val &= ~SPRD_SPI_DMA_EN;
+
+	writel_relaxed(val, ss->base + SPRD_SPI_CTL2);
+}
+
+static int sprd_spi_dma_submit(struct dma_chan *dma_chan,
+			       struct dma_slave_config *c,
+			       struct sg_table *sg,
+			       enum dma_transfer_direction dir)
+{
+	struct dma_async_tx_descriptor *desc;
+	dma_cookie_t cookie;
+	unsigned long flags;
+	int ret;
+
+	ret = dmaengine_slave_config(dma_chan, c);
+	if (ret < 0)
+		return ret;
+
+	flags = SPRD_DMA_FLAGS(SPRD_DMA_CHN_MODE_NONE, SPRD_DMA_NO_TRG,
+			       SPRD_DMA_FRAG_REQ, SPRD_DMA_TRANS_INT);
+	desc = dmaengine_prep_slave_sg(dma_chan, sg->sgl, sg->nents, dir, flags);
+	if (!desc)
+		return  -ENODEV;
+
+	cookie = dmaengine_submit(desc);
+	if (dma_submit_error(cookie))
+		return dma_submit_error(cookie);
+
+	dma_async_issue_pending(dma_chan);
+
+	return 0;
+}
+
+static int sprd_spi_dma_rx_config(struct sprd_spi *ss, struct spi_transfer *t)
+{
+	struct dma_chan *dma_chan = ss->dma.dma_chan[SPRD_SPI_RX];
+	struct dma_slave_config config = {
+		.src_addr = ss->phy_base,
+		.src_addr_width = ss->dma.width,
+		.dst_addr_width = ss->dma.width,
+		.dst_maxburst = ss->dma.fragmens_len,
+	};
+	int ret;
+
+	ret = sprd_spi_dma_submit(dma_chan, &config, &t->rx_sg, DMA_DEV_TO_MEM);
+	if (ret)
+		return ret;
+
+	return ss->dma.rx_len;
+}
+
+static int sprd_spi_dma_tx_config(struct sprd_spi *ss, struct spi_transfer *t)
+{
+	struct dma_chan *dma_chan = ss->dma.dma_chan[SPRD_SPI_TX];
+	struct dma_slave_config config = {
+		.dst_addr = ss->phy_base,
+		.src_addr_width = ss->dma.width,
+		.dst_addr_width = ss->dma.width,
+		.src_maxburst = ss->dma.fragmens_len,
+	};
+	int ret;
+
+	ret = sprd_spi_dma_submit(dma_chan, &config, &t->tx_sg, DMA_MEM_TO_DEV);
+	if (ret)
+		return ret;
+
+	return t->len;
+}
+
+static int sprd_spi_dma_request(struct sprd_spi *ss)
+{
+	ss->dma.dma_chan[SPRD_SPI_RX] = dma_request_chan(ss->dev, "rx_chn");
+	if (IS_ERR_OR_NULL(ss->dma.dma_chan[SPRD_SPI_RX])) {
+		if (PTR_ERR(ss->dma.dma_chan[SPRD_SPI_RX]) == -EPROBE_DEFER)
+			return PTR_ERR(ss->dma.dma_chan[SPRD_SPI_RX]);
+
+		dev_err(ss->dev, "request RX DMA channel failed!\n");
+		return PTR_ERR(ss->dma.dma_chan[SPRD_SPI_RX]);
+	}
+
+	ss->dma.dma_chan[SPRD_SPI_TX]  = dma_request_chan(ss->dev, "tx_chn");
+	if (IS_ERR_OR_NULL(ss->dma.dma_chan[SPRD_SPI_TX])) {
+		if (PTR_ERR(ss->dma.dma_chan[SPRD_SPI_TX]) == -EPROBE_DEFER)
+			return PTR_ERR(ss->dma.dma_chan[SPRD_SPI_TX]);
+
+		dev_err(ss->dev, "request TX DMA channel failed!\n");
+		dma_release_channel(ss->dma.dma_chan[SPRD_SPI_RX]);
+		return PTR_ERR(ss->dma.dma_chan[SPRD_SPI_TX]);
+	}
+
+	return 0;
+}
+
+static void sprd_spi_dma_release(struct sprd_spi *ss)
+{
+	if (ss->dma.dma_chan[SPRD_SPI_RX])
+		dma_release_channel(ss->dma.dma_chan[SPRD_SPI_RX]);
+
+	if (ss->dma.dma_chan[SPRD_SPI_TX])
+		dma_release_channel(ss->dma.dma_chan[SPRD_SPI_TX]);
+}
+
+static int sprd_spi_dma_txrx_bufs(struct spi_device *sdev,
+				  struct spi_transfer *t)
+{
+	struct sprd_spi *ss = spi_master_get_devdata(sdev->master);
+	u32 trans_len = ss->trans_len;
+	int ret, write_size = 0;
+
+	reinit_completion(&ss->xfer_completion);
+	sprd_spi_irq_enable(ss);
+	if (ss->trans_mode & SPRD_SPI_TX_MODE) {
+		write_size = sprd_spi_dma_tx_config(ss, t);
+		sprd_spi_set_tx_length(ss, trans_len);
+
+		/*
+		 * For our 3 wires mode or dual TX line mode, we need
+		 * to request the controller to transfer.
+		 */
+		if (ss->hw_mode & SPI_3WIRE || ss->hw_mode & SPI_TX_DUAL)
+			sprd_spi_tx_req(ss);
+	} else {
+		sprd_spi_set_rx_length(ss, trans_len);
+
+		/*
+		 * For our 3 wires mode or dual TX line mode, we need
+		 * to request the controller to read.
+		 */
+		if (ss->hw_mode & SPI_3WIRE || ss->hw_mode & SPI_TX_DUAL)
+			sprd_spi_rx_req(ss);
+		else
+			write_size = ss->write_bufs(ss, trans_len);
+	}
+
+	if (write_size < 0) {
+		ret = write_size;
+		dev_err(ss->dev, "failed to write, ret = %d\n", ret);
+		goto trans_complete;
+	}
+
+	if (ss->trans_mode & SPRD_SPI_RX_MODE) {
+		/*
+		 * Set up the DMA receive data length, which must be an
+		 * integral multiple of fragment length. But when the length
+		 * of received data is less than fragment length, DMA can be
+		 * configured to receive data according to the actual length
+		 * of received data.
+		 */
+		ss->dma.rx_len = t->len > ss->dma.fragmens_len ?
+			(t->len - t->len % ss->dma.fragmens_len) :
+			 t->len;
+		ret = sprd_spi_dma_rx_config(ss, t);
+		if (ret < 0) {
+			dev_err(&sdev->dev,
+				"failed to configure rx DMA, ret = %d\n", ret);
+			goto trans_complete;
+		}
+	}
+
+	sprd_spi_dma_enable(ss, true);
+	wait_for_completion(&(ss->xfer_completion));
+
+	if (ss->trans_mode & SPRD_SPI_TX_MODE)
+		ret = write_size;
+	else
+		ret = ss->dma.rx_len;
+
+trans_complete:
+	sprd_spi_dma_enable(ss, false);
+	sprd_spi_enter_idle(ss);
+	sprd_spi_irq_disable(ss);
+
+	return ret;
+}
+
 static void sprd_spi_set_speed(struct sprd_spi *ss, u32 speed_hz)
 {
 	/*
@@ -514,16 +741,22 @@ static int sprd_spi_setup_transfer(struct spi_device *sdev,
 		ss->trans_len = t->len;
 		ss->read_bufs = sprd_spi_read_bufs_u8;
 		ss->write_bufs = sprd_spi_write_bufs_u8;
+		ss->dma.width = DMA_SLAVE_BUSWIDTH_1_BYTE;
+		ss->dma.fragmens_len = SPRD_SPI_DMA_STEP;
 		break;
 	case 16:
 		ss->trans_len = t->len >> 1;
 		ss->read_bufs = sprd_spi_read_bufs_u16;
 		ss->write_bufs = sprd_spi_write_bufs_u16;
+		ss->dma.width = DMA_SLAVE_BUSWIDTH_2_BYTES;
+		ss->dma.fragmens_len = SPRD_SPI_DMA_STEP << 1;
 		break;
 	case 32:
 		ss->trans_len = t->len >> 2;
 		ss->read_bufs = sprd_spi_read_bufs_u32;
 		ss->write_bufs = sprd_spi_write_bufs_u32;
+		ss->dma.width = DMA_SLAVE_BUSWIDTH_4_BYTES;
+		ss->dma.fragmens_len = SPRD_SPI_DMA_STEP << 2;
 		break;
 	default:
 		return -EINVAL;
@@ -561,7 +794,11 @@ static int sprd_spi_transfer_one(struct spi_controller *sctlr,
 	if (ret)
 		goto setup_err;
 
-	ret = sprd_spi_txrx_bufs(sdev, t);
+	if (sctlr->can_dma(sctlr, sdev, t))
+		ret = sprd_spi_dma_txrx_bufs(sdev, t);
+	else
+		ret = sprd_spi_txrx_bufs(sdev, t);
+
 	if (ret == t->len)
 		ret = 0;
 	else if (ret >= 0)
@@ -573,6 +810,53 @@ static int sprd_spi_transfer_one(struct spi_controller *sctlr,
 	return ret;
 }
 
+static irqreturn_t sprd_spi_handle_irq(int irq, void *data)
+{
+	struct sprd_spi *ss = (struct sprd_spi *)data;
+	u32 val = readl_relaxed(ss->base + SPRD_SPI_INT_MASK_STS);
+
+	if (val & SPRD_SPI_MASK_TX_END) {
+		writel_relaxed(SPRD_SPI_TX_END_CLR, ss->base + SPRD_SPI_INT_CLR);
+		if (!(ss->trans_mode & SPRD_SPI_RX_MODE))
+			complete(&ss->xfer_completion);
+
+		return IRQ_HANDLED;
+	}
+
+	if (val & SPRD_SPI_MASK_RX_END) {
+		writel_relaxed(SPRD_SPI_RX_END_CLR, ss->base + SPRD_SPI_INT_CLR);
+		if (ss->dma.rx_len < ss->len) {
+			ss->rx_buf += ss->dma.rx_len;
+			ss->dma.rx_len +=
+				ss->read_bufs(ss, ss->len - ss->dma.rx_len);
+		}
+		complete(&ss->xfer_completion);
+
+		return IRQ_HANDLED;
+	}
+
+	return IRQ_NONE;
+}
+
+static int sprd_spi_irq_init(struct platform_device *pdev, struct sprd_spi *ss)
+{
+	int ret;
+
+	ss->irq = platform_get_irq(pdev, 0);
+	if (ss->irq < 0) {
+		dev_err(&pdev->dev, "failed to get irq resource\n");
+		return ss->irq;
+	}
+
+	ret = devm_request_irq(&pdev->dev, ss->irq, sprd_spi_handle_irq,
+				0, pdev->name, ss);
+	if (ret)
+		dev_err(&pdev->dev, "failed to request spi irq %d, ret = %d\n",
+			ss->irq, ret);
+
+	return ret;
+}
+
 static int sprd_spi_clk_init(struct platform_device *pdev, struct sprd_spi *ss)
 {
 	struct clk *clk_spi, *clk_parent;
@@ -603,6 +887,35 @@ static int sprd_spi_clk_init(struct platform_device *pdev, struct sprd_spi *ss)
 	return 0;
 }
 
+static bool sprd_spi_can_dma(struct spi_controller *sctlr,
+			     struct spi_device *spi, struct spi_transfer *t)
+{
+	struct sprd_spi *ss = spi_controller_get_devdata(sctlr);
+
+	return ss->dma.enable && (t->len > SPRD_SPI_FIFO_SIZE);
+}
+
+static int sprd_spi_dma_init(struct platform_device *pdev, struct sprd_spi *ss)
+{
+	int ret;
+
+	ret = sprd_spi_dma_request(ss);
+	if (ret) {
+		if (ret == -EPROBE_DEFER)
+			return ret;
+
+		dev_warn(&pdev->dev,
+			 "failed to request dma, enter no dma mode, ret = %d\n",
+			 ret);
+
+		return 0;
+	}
+
+	ss->dma.enable = true;
+
+	return 0;
+}
+
 static int sprd_spi_probe(struct platform_device *pdev)
 {
 	struct spi_controller *sctlr;
@@ -623,25 +936,36 @@ static int sprd_spi_probe(struct platform_device *pdev)
 		goto free_controller;
 	}
 
+	ss->phy_base = res->start;
 	ss->dev = &pdev->dev;
 	sctlr->dev.of_node = pdev->dev.of_node;
 	sctlr->mode_bits = SPI_CPOL | SPI_CPHA | SPI_3WIRE | SPI_TX_DUAL;
 	sctlr->bus_num = pdev->id;
 	sctlr->set_cs = sprd_spi_chipselect;
 	sctlr->transfer_one = sprd_spi_transfer_one;
+	sctlr->can_dma = sprd_spi_can_dma;
 	sctlr->auto_runtime_pm = true;
 	sctlr->max_speed_hz = min_t(u32, ss->src_clk >> 1,
 				    SPRD_SPI_MAX_SPEED_HZ);
 
+	init_completion(&ss->xfer_completion);
 	platform_set_drvdata(pdev, sctlr);
 	ret = sprd_spi_clk_init(pdev, ss);
 	if (ret)
 		goto free_controller;
 
-	ret = clk_prepare_enable(ss->clk);
+	ret = sprd_spi_irq_init(pdev, ss);
 	if (ret)
 		goto free_controller;
 
+	ret = sprd_spi_dma_init(pdev, ss);
+	if (ret)
+		goto free_controller;
+
+	ret = clk_prepare_enable(ss->clk);
+	if (ret)
+		goto release_dma;
+
 	ret = pm_runtime_set_active(&pdev->dev);
 	if (ret < 0)
 		goto disable_clk;
@@ -670,6 +994,8 @@ static int sprd_spi_probe(struct platform_device *pdev)
 	pm_runtime_disable(&pdev->dev);
 disable_clk:
 	clk_disable_unprepare(ss->clk);
+release_dma:
+	sprd_spi_dma_release(ss);
 free_controller:
 	spi_controller_put(sctlr);
 
@@ -688,6 +1014,10 @@ static int sprd_spi_remove(struct platform_device *pdev)
 		return ret;
 	}
 
+	spi_controller_suspend(sctlr);
+
+	if (ss->dma.enable)
+		sprd_spi_dma_release(ss);
 	clk_disable_unprepare(ss->clk);
 	pm_runtime_put_noidle(&pdev->dev);
 	pm_runtime_disable(&pdev->dev);
@@ -700,6 +1030,9 @@ static int __maybe_unused sprd_spi_runtime_suspend(struct device *dev)
 	struct spi_controller *sctlr = dev_get_drvdata(dev);
 	struct sprd_spi *ss = spi_controller_get_devdata(sctlr);
 
+	if (ss->dma.enable)
+		sprd_spi_dma_release(ss);
+
 	clk_disable_unprepare(ss->clk);
 
 	return 0;
@@ -715,7 +1048,14 @@ static int __maybe_unused sprd_spi_runtime_resume(struct device *dev)
 	if (ret)
 		return ret;
 
-	return 0;
+	if (!ss->dma.enable)
+		return 0;
+
+	ret = sprd_spi_dma_request(ss);
+	if (ret)
+		clk_disable_unprepare(ss->clk);
+
+	return ret;
 }
 
 static const struct dev_pm_ops sprd_spi_pm_ops = {
diff --git a/drivers/spi/spi-stm32.c b/drivers/spi/spi-stm32.c
index ad1e55d3d5d5..4186ed20d796 100644
--- a/drivers/spi/spi-stm32.c
+++ b/drivers/spi/spi-stm32.c
@@ -1,23 +1,10 @@
-/*
- * STMicroelectronics STM32 SPI Controller driver (master mode only)
- *
- * Copyright (C) 2017, STMicroelectronics - All Rights Reserved
- * Author(s): Amelie Delaunay <amelie.delaunay@st.com> for STMicroelectronics.
- *
- * License terms: GPL V2.0.
- *
- * spi_stm32 driver is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License version 2 as published by
- * the Free Software Foundation.
- *
- * spi_stm32 driver is distributed in the hope that it will be useful, but
- * WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more
- * details.
- *
- * You should have received a copy of the GNU General Public License along with
- * spi_stm32 driver. If not, see <http://www.gnu.org/licenses/>.
- */
+// SPDX-License-Identifier: GPL-2.0
+//
+// STMicroelectronics STM32 SPI Controller driver (master mode only)
+//
+// Copyright (C) 2017, STMicroelectronics - All Rights Reserved
+// Author(s): Amelie Delaunay <amelie.delaunay@st.com> for STMicroelectronics.
+
 #include <linux/debugfs.h>
 #include <linux/clk.h>
 #include <linux/delay.h>
@@ -33,99 +20,251 @@
 
 #define DRIVER_NAME "spi_stm32"
 
-/* STM32 SPI registers */
-#define STM32_SPI_CR1		0x00
-#define STM32_SPI_CR2		0x04
-#define STM32_SPI_CFG1		0x08
-#define STM32_SPI_CFG2		0x0C
-#define STM32_SPI_IER		0x10
-#define STM32_SPI_SR		0x14
-#define STM32_SPI_IFCR		0x18
-#define STM32_SPI_TXDR		0x20
-#define STM32_SPI_RXDR		0x30
-#define STM32_SPI_I2SCFGR	0x50
-
-/* STM32_SPI_CR1 bit fields */
-#define SPI_CR1_SPE		BIT(0)
-#define SPI_CR1_MASRX		BIT(8)
-#define SPI_CR1_CSTART		BIT(9)
-#define SPI_CR1_CSUSP		BIT(10)
-#define SPI_CR1_HDDIR		BIT(11)
-#define SPI_CR1_SSI		BIT(12)
-
-/* STM32_SPI_CR2 bit fields */
-#define SPI_CR2_TSIZE_SHIFT	0
-#define SPI_CR2_TSIZE		GENMASK(15, 0)
-
-/* STM32_SPI_CFG1 bit fields */
-#define SPI_CFG1_DSIZE_SHIFT	0
-#define SPI_CFG1_DSIZE		GENMASK(4, 0)
-#define SPI_CFG1_FTHLV_SHIFT	5
-#define SPI_CFG1_FTHLV		GENMASK(8, 5)
-#define SPI_CFG1_RXDMAEN	BIT(14)
-#define SPI_CFG1_TXDMAEN	BIT(15)
-#define SPI_CFG1_MBR_SHIFT	28
-#define SPI_CFG1_MBR		GENMASK(30, 28)
-#define SPI_CFG1_MBR_MIN	0
-#define SPI_CFG1_MBR_MAX	(GENMASK(30, 28) >> 28)
-
-/* STM32_SPI_CFG2 bit fields */
-#define SPI_CFG2_MIDI_SHIFT	4
-#define SPI_CFG2_MIDI		GENMASK(7, 4)
-#define SPI_CFG2_COMM_SHIFT	17
-#define SPI_CFG2_COMM		GENMASK(18, 17)
-#define SPI_CFG2_SP_SHIFT	19
-#define SPI_CFG2_SP		GENMASK(21, 19)
-#define SPI_CFG2_MASTER		BIT(22)
-#define SPI_CFG2_LSBFRST	BIT(23)
-#define SPI_CFG2_CPHA		BIT(24)
-#define SPI_CFG2_CPOL		BIT(25)
-#define SPI_CFG2_SSM		BIT(26)
-#define SPI_CFG2_AFCNTR		BIT(31)
-
-/* STM32_SPI_IER bit fields */
-#define SPI_IER_RXPIE		BIT(0)
-#define SPI_IER_TXPIE		BIT(1)
-#define SPI_IER_DXPIE		BIT(2)
-#define SPI_IER_EOTIE		BIT(3)
-#define SPI_IER_TXTFIE		BIT(4)
-#define SPI_IER_OVRIE		BIT(6)
-#define SPI_IER_MODFIE		BIT(9)
-#define SPI_IER_ALL		GENMASK(10, 0)
-
-/* STM32_SPI_SR bit fields */
-#define SPI_SR_RXP		BIT(0)
-#define SPI_SR_TXP		BIT(1)
-#define SPI_SR_EOT		BIT(3)
-#define SPI_SR_OVR		BIT(6)
-#define SPI_SR_MODF		BIT(9)
-#define SPI_SR_SUSP		BIT(11)
-#define SPI_SR_RXPLVL_SHIFT	13
-#define SPI_SR_RXPLVL		GENMASK(14, 13)
-#define SPI_SR_RXWNE		BIT(15)
-
-/* STM32_SPI_IFCR bit fields */
-#define SPI_IFCR_ALL		GENMASK(11, 3)
-
-/* STM32_SPI_I2SCFGR bit fields */
-#define SPI_I2SCFGR_I2SMOD	BIT(0)
-
-/* SPI Master Baud Rate min/max divisor */
-#define SPI_MBR_DIV_MIN		(2 << SPI_CFG1_MBR_MIN)
-#define SPI_MBR_DIV_MAX		(2 << SPI_CFG1_MBR_MAX)
-
-/* SPI Communication mode */
+/* STM32F4 SPI registers */
+#define STM32F4_SPI_CR1			0x00
+#define STM32F4_SPI_CR2			0x04
+#define STM32F4_SPI_SR			0x08
+#define STM32F4_SPI_DR			0x0C
+#define STM32F4_SPI_I2SCFGR		0x1C
+
+/* STM32F4_SPI_CR1 bit fields */
+#define STM32F4_SPI_CR1_CPHA		BIT(0)
+#define STM32F4_SPI_CR1_CPOL		BIT(1)
+#define STM32F4_SPI_CR1_MSTR		BIT(2)
+#define STM32F4_SPI_CR1_BR_SHIFT	3
+#define STM32F4_SPI_CR1_BR		GENMASK(5, 3)
+#define STM32F4_SPI_CR1_SPE		BIT(6)
+#define STM32F4_SPI_CR1_LSBFRST		BIT(7)
+#define STM32F4_SPI_CR1_SSI		BIT(8)
+#define STM32F4_SPI_CR1_SSM		BIT(9)
+#define STM32F4_SPI_CR1_RXONLY		BIT(10)
+#define STM32F4_SPI_CR1_DFF		BIT(11)
+#define STM32F4_SPI_CR1_CRCNEXT		BIT(12)
+#define STM32F4_SPI_CR1_CRCEN		BIT(13)
+#define STM32F4_SPI_CR1_BIDIOE		BIT(14)
+#define STM32F4_SPI_CR1_BIDIMODE	BIT(15)
+#define STM32F4_SPI_CR1_BR_MIN		0
+#define STM32F4_SPI_CR1_BR_MAX		(GENMASK(5, 3) >> 3)
+
+/* STM32F4_SPI_CR2 bit fields */
+#define STM32F4_SPI_CR2_RXDMAEN		BIT(0)
+#define STM32F4_SPI_CR2_TXDMAEN		BIT(1)
+#define STM32F4_SPI_CR2_SSOE		BIT(2)
+#define STM32F4_SPI_CR2_FRF		BIT(4)
+#define STM32F4_SPI_CR2_ERRIE		BIT(5)
+#define STM32F4_SPI_CR2_RXNEIE		BIT(6)
+#define STM32F4_SPI_CR2_TXEIE		BIT(7)
+
+/* STM32F4_SPI_SR bit fields */
+#define STM32F4_SPI_SR_RXNE		BIT(0)
+#define STM32F4_SPI_SR_TXE		BIT(1)
+#define STM32F4_SPI_SR_CHSIDE		BIT(2)
+#define STM32F4_SPI_SR_UDR		BIT(3)
+#define STM32F4_SPI_SR_CRCERR		BIT(4)
+#define STM32F4_SPI_SR_MODF		BIT(5)
+#define STM32F4_SPI_SR_OVR		BIT(6)
+#define STM32F4_SPI_SR_BSY		BIT(7)
+#define STM32F4_SPI_SR_FRE		BIT(8)
+
+/* STM32F4_SPI_I2SCFGR bit fields */
+#define STM32F4_SPI_I2SCFGR_I2SMOD	BIT(11)
+
+/* STM32F4 SPI Baud Rate min/max divisor */
+#define STM32F4_SPI_BR_DIV_MIN		(2 << STM32F4_SPI_CR1_BR_MIN)
+#define STM32F4_SPI_BR_DIV_MAX		(2 << STM32F4_SPI_CR1_BR_MAX)
+
+/* STM32H7 SPI registers */
+#define STM32H7_SPI_CR1			0x00
+#define STM32H7_SPI_CR2			0x04
+#define STM32H7_SPI_CFG1		0x08
+#define STM32H7_SPI_CFG2		0x0C
+#define STM32H7_SPI_IER			0x10
+#define STM32H7_SPI_SR			0x14
+#define STM32H7_SPI_IFCR		0x18
+#define STM32H7_SPI_TXDR		0x20
+#define STM32H7_SPI_RXDR		0x30
+#define STM32H7_SPI_I2SCFGR		0x50
+
+/* STM32H7_SPI_CR1 bit fields */
+#define STM32H7_SPI_CR1_SPE		BIT(0)
+#define STM32H7_SPI_CR1_MASRX		BIT(8)
+#define STM32H7_SPI_CR1_CSTART		BIT(9)
+#define STM32H7_SPI_CR1_CSUSP		BIT(10)
+#define STM32H7_SPI_CR1_HDDIR		BIT(11)
+#define STM32H7_SPI_CR1_SSI		BIT(12)
+
+/* STM32H7_SPI_CR2 bit fields */
+#define STM32H7_SPI_CR2_TSIZE_SHIFT	0
+#define STM32H7_SPI_CR2_TSIZE		GENMASK(15, 0)
+
+/* STM32H7_SPI_CFG1 bit fields */
+#define STM32H7_SPI_CFG1_DSIZE_SHIFT	0
+#define STM32H7_SPI_CFG1_DSIZE		GENMASK(4, 0)
+#define STM32H7_SPI_CFG1_FTHLV_SHIFT	5
+#define STM32H7_SPI_CFG1_FTHLV		GENMASK(8, 5)
+#define STM32H7_SPI_CFG1_RXDMAEN	BIT(14)
+#define STM32H7_SPI_CFG1_TXDMAEN	BIT(15)
+#define STM32H7_SPI_CFG1_MBR_SHIFT	28
+#define STM32H7_SPI_CFG1_MBR		GENMASK(30, 28)
+#define STM32H7_SPI_CFG1_MBR_MIN	0
+#define STM32H7_SPI_CFG1_MBR_MAX	(GENMASK(30, 28) >> 28)
+
+/* STM32H7_SPI_CFG2 bit fields */
+#define STM32H7_SPI_CFG2_MIDI_SHIFT	4
+#define STM32H7_SPI_CFG2_MIDI		GENMASK(7, 4)
+#define STM32H7_SPI_CFG2_COMM_SHIFT	17
+#define STM32H7_SPI_CFG2_COMM		GENMASK(18, 17)
+#define STM32H7_SPI_CFG2_SP_SHIFT	19
+#define STM32H7_SPI_CFG2_SP		GENMASK(21, 19)
+#define STM32H7_SPI_CFG2_MASTER		BIT(22)
+#define STM32H7_SPI_CFG2_LSBFRST	BIT(23)
+#define STM32H7_SPI_CFG2_CPHA		BIT(24)
+#define STM32H7_SPI_CFG2_CPOL		BIT(25)
+#define STM32H7_SPI_CFG2_SSM		BIT(26)
+#define STM32H7_SPI_CFG2_AFCNTR		BIT(31)
+
+/* STM32H7_SPI_IER bit fields */
+#define STM32H7_SPI_IER_RXPIE		BIT(0)
+#define STM32H7_SPI_IER_TXPIE		BIT(1)
+#define STM32H7_SPI_IER_DXPIE		BIT(2)
+#define STM32H7_SPI_IER_EOTIE		BIT(3)
+#define STM32H7_SPI_IER_TXTFIE		BIT(4)
+#define STM32H7_SPI_IER_OVRIE		BIT(6)
+#define STM32H7_SPI_IER_MODFIE		BIT(9)
+#define STM32H7_SPI_IER_ALL		GENMASK(10, 0)
+
+/* STM32H7_SPI_SR bit fields */
+#define STM32H7_SPI_SR_RXP		BIT(0)
+#define STM32H7_SPI_SR_TXP		BIT(1)
+#define STM32H7_SPI_SR_EOT		BIT(3)
+#define STM32H7_SPI_SR_OVR		BIT(6)
+#define STM32H7_SPI_SR_MODF		BIT(9)
+#define STM32H7_SPI_SR_SUSP		BIT(11)
+#define STM32H7_SPI_SR_RXPLVL_SHIFT	13
+#define STM32H7_SPI_SR_RXPLVL		GENMASK(14, 13)
+#define STM32H7_SPI_SR_RXWNE		BIT(15)
+
+/* STM32H7_SPI_IFCR bit fields */
+#define STM32H7_SPI_IFCR_ALL		GENMASK(11, 3)
+
+/* STM32H7_SPI_I2SCFGR bit fields */
+#define STM32H7_SPI_I2SCFGR_I2SMOD	BIT(0)
+
+/* STM32H7 SPI Master Baud Rate min/max divisor */
+#define STM32H7_SPI_MBR_DIV_MIN		(2 << STM32H7_SPI_CFG1_MBR_MIN)
+#define STM32H7_SPI_MBR_DIV_MAX		(2 << STM32H7_SPI_CFG1_MBR_MAX)
+
+/* STM32H7 SPI Communication mode */
+#define STM32H7_SPI_FULL_DUPLEX		0
+#define STM32H7_SPI_SIMPLEX_TX		1
+#define STM32H7_SPI_SIMPLEX_RX		2
+#define STM32H7_SPI_HALF_DUPLEX		3
+
+/* SPI Communication type */
 #define SPI_FULL_DUPLEX		0
 #define SPI_SIMPLEX_TX		1
 #define SPI_SIMPLEX_RX		2
-#define SPI_HALF_DUPLEX		3
+#define SPI_3WIRE_TX		3
+#define SPI_3WIRE_RX		4
 
 #define SPI_1HZ_NS		1000000000
 
+/*
+ * use PIO for small transfers, avoiding DMA setup/teardown overhead for drivers
+ * without fifo buffers.
+ */
+#define SPI_DMA_MIN_BYTES	16
+
+/**
+ * stm32_spi_reg - stm32 SPI register & bitfield desc
+ * @reg:		register offset
+ * @mask:		bitfield mask
+ * @shift:		left shift
+ */
+struct stm32_spi_reg {
+	int reg;
+	int mask;
+	int shift;
+};
+
+/**
+ * stm32_spi_regspec - stm32 registers definition, compatible dependent data
+ * en: enable register and SPI enable bit
+ * dma_rx_en: SPI DMA RX enable register end SPI DMA RX enable bit
+ * dma_tx_en: SPI DMA TX enable register end SPI DMA TX enable bit
+ * cpol: clock polarity register and polarity bit
+ * cpha: clock phase register and phase bit
+ * lsb_first: LSB transmitted first register and bit
+ * br: baud rate register and bitfields
+ * rx: SPI RX data register
+ * tx: SPI TX data register
+ */
+struct stm32_spi_regspec {
+	const struct stm32_spi_reg en;
+	const struct stm32_spi_reg dma_rx_en;
+	const struct stm32_spi_reg dma_tx_en;
+	const struct stm32_spi_reg cpol;
+	const struct stm32_spi_reg cpha;
+	const struct stm32_spi_reg lsb_first;
+	const struct stm32_spi_reg br;
+	const struct stm32_spi_reg rx;
+	const struct stm32_spi_reg tx;
+};
+
+struct stm32_spi;
+
+/**
+ * stm32_spi_cfg - stm32 compatible configuration data
+ * @regs: registers descriptions
+ * @get_fifo_size: routine to get fifo size
+ * @get_bpw_mask: routine to get bits per word mask
+ * @disable: routine to disable controller
+ * @config: routine to configure controller as SPI Master
+ * @set_bpw: routine to configure registers to for bits per word
+ * @set_mode: routine to configure registers to desired mode
+ * @set_data_idleness: optional routine to configure registers to desired idle
+ * time between frames (if driver has this functionality)
+ * set_number_of_data: optional routine to configure registers to desired
+ * number of data (if driver has this functionality)
+ * @can_dma: routine to determine if the transfer is eligible for DMA use
+ * @transfer_one_dma_start: routine to start transfer a single spi_transfer
+ * using DMA
+ * @dma_rx cb: routine to call after DMA RX channel operation is complete
+ * @dma_tx cb: routine to call after DMA TX channel operation is complete
+ * @transfer_one_irq: routine to configure interrupts for driver
+ * @irq_handler_event: Interrupt handler for SPI controller events
+ * @irq_handler_thread: thread of interrupt handler for SPI controller
+ * @baud_rate_div_min: minimum baud rate divisor
+ * @baud_rate_div_max: maximum baud rate divisor
+ * @has_fifo: boolean to know if fifo is used for driver
+ * @has_startbit: boolean to know if start bit is used to start transfer
+ */
+struct stm32_spi_cfg {
+	const struct stm32_spi_regspec *regs;
+	int (*get_fifo_size)(struct stm32_spi *spi);
+	int (*get_bpw_mask)(struct stm32_spi *spi);
+	void (*disable)(struct stm32_spi *spi);
+	int (*config)(struct stm32_spi *spi);
+	void (*set_bpw)(struct stm32_spi *spi);
+	int (*set_mode)(struct stm32_spi *spi, unsigned int comm_type);
+	void (*set_data_idleness)(struct stm32_spi *spi, u32 length);
+	int (*set_number_of_data)(struct stm32_spi *spi, u32 length);
+	void (*transfer_one_dma_start)(struct stm32_spi *spi);
+	void (*dma_rx_cb)(void *data);
+	void (*dma_tx_cb)(void *data);
+	int (*transfer_one_irq)(struct stm32_spi *spi);
+	irqreturn_t (*irq_handler_event)(int irq, void *dev_id);
+	irqreturn_t (*irq_handler_thread)(int irq, void *dev_id);
+	unsigned int baud_rate_div_min;
+	unsigned int baud_rate_div_max;
+	bool has_fifo;
+};
+
 /**
  * struct stm32_spi - private data of the SPI controller
  * @dev: driver model representation of the controller
  * @master: controller master interface
+ * @cfg: compatible configuration data
  * @base: virtual memory area
  * @clk: hw kernel clock feeding the SPI clock generator
  * @clk_rate: rate of the hw kernel clock feeding the SPI clock generator
@@ -151,6 +290,7 @@
 struct stm32_spi {
 	struct device *dev;
 	struct spi_master *master;
+	const struct stm32_spi_cfg *cfg;
 	void __iomem *base;
 	struct clk *clk;
 	u32 clk_rate;
@@ -176,6 +316,40 @@ struct stm32_spi {
 	dma_addr_t phys_addr;
 };
 
+static const struct stm32_spi_regspec stm32f4_spi_regspec = {
+	.en = { STM32F4_SPI_CR1, STM32F4_SPI_CR1_SPE },
+
+	.dma_rx_en = { STM32F4_SPI_CR2, STM32F4_SPI_CR2_RXDMAEN },
+	.dma_tx_en = { STM32F4_SPI_CR2, STM32F4_SPI_CR2_TXDMAEN },
+
+	.cpol = { STM32F4_SPI_CR1, STM32F4_SPI_CR1_CPOL },
+	.cpha = { STM32F4_SPI_CR1, STM32F4_SPI_CR1_CPHA },
+	.lsb_first = { STM32F4_SPI_CR1, STM32F4_SPI_CR1_LSBFRST },
+	.br = { STM32F4_SPI_CR1, STM32F4_SPI_CR1_BR, STM32F4_SPI_CR1_BR_SHIFT },
+
+	.rx = { STM32F4_SPI_DR },
+	.tx = { STM32F4_SPI_DR },
+};
+
+static const struct stm32_spi_regspec stm32h7_spi_regspec = {
+	/* SPI data transfer is enabled but spi_ker_ck is idle.
+	 * CFG1 and CFG2 registers are write protected when SPE is enabled.
+	 */
+	.en = { STM32H7_SPI_CR1, STM32H7_SPI_CR1_SPE },
+
+	.dma_rx_en = { STM32H7_SPI_CFG1, STM32H7_SPI_CFG1_RXDMAEN },
+	.dma_tx_en = { STM32H7_SPI_CFG1, STM32H7_SPI_CFG1_TXDMAEN },
+
+	.cpol = { STM32H7_SPI_CFG2, STM32H7_SPI_CFG2_CPOL },
+	.cpha = { STM32H7_SPI_CFG2, STM32H7_SPI_CFG2_CPHA },
+	.lsb_first = { STM32H7_SPI_CFG2, STM32H7_SPI_CFG2_LSBFRST },
+	.br = { STM32H7_SPI_CFG1, STM32H7_SPI_CFG1_MBR,
+		STM32H7_SPI_CFG1_MBR_SHIFT },
+
+	.rx = { STM32H7_SPI_RXDR },
+	.tx = { STM32H7_SPI_TXDR },
+};
+
 static inline void stm32_spi_set_bits(struct stm32_spi *spi,
 				      u32 offset, u32 bits)
 {
@@ -191,22 +365,22 @@ static inline void stm32_spi_clr_bits(struct stm32_spi *spi,
 }
 
 /**
- * stm32_spi_get_fifo_size - Return fifo size
+ * stm32h7_spi_get_fifo_size - Return fifo size
  * @spi: pointer to the spi controller data structure
  */
-static int stm32_spi_get_fifo_size(struct stm32_spi *spi)
+static int stm32h7_spi_get_fifo_size(struct stm32_spi *spi)
 {
 	unsigned long flags;
 	u32 count = 0;
 
 	spin_lock_irqsave(&spi->lock, flags);
 
-	stm32_spi_set_bits(spi, STM32_SPI_CR1, SPI_CR1_SPE);
+	stm32_spi_set_bits(spi, STM32H7_SPI_CR1, STM32H7_SPI_CR1_SPE);
 
-	while (readl_relaxed(spi->base + STM32_SPI_SR) & SPI_SR_TXP)
-		writeb_relaxed(++count, spi->base + STM32_SPI_TXDR);
+	while (readl_relaxed(spi->base + STM32H7_SPI_SR) & STM32H7_SPI_SR_TXP)
+		writeb_relaxed(++count, spi->base + STM32H7_SPI_TXDR);
 
-	stm32_spi_clr_bits(spi, STM32_SPI_CR1, SPI_CR1_SPE);
+	stm32_spi_clr_bits(spi, STM32H7_SPI_CR1, STM32H7_SPI_CR1_SPE);
 
 	spin_unlock_irqrestore(&spi->lock, flags);
 
@@ -216,10 +390,20 @@ static int stm32_spi_get_fifo_size(struct stm32_spi *spi)
 }
 
 /**
- * stm32_spi_get_bpw_mask - Return bits per word mask
+ * stm32f4_spi_get_bpw_mask - Return bits per word mask
  * @spi: pointer to the spi controller data structure
  */
-static int stm32_spi_get_bpw_mask(struct stm32_spi *spi)
+static int stm32f4_spi_get_bpw_mask(struct stm32_spi *spi)
+{
+	dev_dbg(spi->dev, "8-bit or 16-bit data frame supported\n");
+	return SPI_BPW_MASK(8) | SPI_BPW_MASK(16);
+}
+
+/**
+ * stm32h7_spi_get_bpw_mask - Return bits per word mask
+ * @spi: pointer to the spi controller data structure
+ */
+static int stm32h7_spi_get_bpw_mask(struct stm32_spi *spi)
 {
 	unsigned long flags;
 	u32 cfg1, max_bpw;
@@ -230,10 +414,11 @@ static int stm32_spi_get_bpw_mask(struct stm32_spi *spi)
 	 * The most significant bit at DSIZE bit field is reserved when the
 	 * maximum data size of periperal instances is limited to 16-bit
 	 */
-	stm32_spi_set_bits(spi, STM32_SPI_CFG1, SPI_CFG1_DSIZE);
+	stm32_spi_set_bits(spi, STM32H7_SPI_CFG1, STM32H7_SPI_CFG1_DSIZE);
 
-	cfg1 = readl_relaxed(spi->base + STM32_SPI_CFG1);
-	max_bpw = (cfg1 & SPI_CFG1_DSIZE) >> SPI_CFG1_DSIZE_SHIFT;
+	cfg1 = readl_relaxed(spi->base + STM32H7_SPI_CFG1);
+	max_bpw = (cfg1 & STM32H7_SPI_CFG1_DSIZE) >>
+		  STM32H7_SPI_CFG1_DSIZE_SHIFT;
 	max_bpw += 1;
 
 	spin_unlock_irqrestore(&spi->lock, flags);
@@ -244,13 +429,16 @@ static int stm32_spi_get_bpw_mask(struct stm32_spi *spi)
 }
 
 /**
- * stm32_spi_prepare_mbr - Determine SPI_CFG1.MBR value
+ * stm32_spi_prepare_mbr - Determine baud rate divisor value
  * @spi: pointer to the spi controller data structure
  * @speed_hz: requested speed
+ * @min_div: minimum baud rate divisor
+ * @max_div: maximum baud rate divisor
  *
- * Return SPI_CFG1.MBR value in case of success or -EINVAL
+ * Return baud rate divisor value in case of success or -EINVAL
  */
-static int stm32_spi_prepare_mbr(struct stm32_spi *spi, u32 speed_hz)
+static int stm32_spi_prepare_mbr(struct stm32_spi *spi, u32 speed_hz,
+				 u32 min_div, u32 max_div)
 {
 	u32 div, mbrdiv;
 
@@ -263,8 +451,7 @@ static int stm32_spi_prepare_mbr(struct stm32_spi *spi, u32 speed_hz)
 	 * no need to check it there.
 	 * However, we need to ensure the following calculations.
 	 */
-	if (div < SPI_MBR_DIV_MIN ||
-	    div > SPI_MBR_DIV_MAX)
+	if ((div < min_div) || (div > max_div))
 		return -EINVAL;
 
 	/* Determine the first power of 2 greater than or equal to div */
@@ -279,10 +466,10 @@ static int stm32_spi_prepare_mbr(struct stm32_spi *spi, u32 speed_hz)
 }
 
 /**
- * stm32_spi_prepare_fthlv - Determine FIFO threshold level
+ * stm32h7_spi_prepare_fthlv - Determine FIFO threshold level
  * @spi: pointer to the spi controller data structure
  */
-static u32 stm32_spi_prepare_fthlv(struct stm32_spi *spi)
+static u32 stm32h7_spi_prepare_fthlv(struct stm32_spi *spi)
 {
 	u32 fthlv, half_fifo;
 
@@ -306,32 +493,62 @@ static u32 stm32_spi_prepare_fthlv(struct stm32_spi *spi)
 }
 
 /**
- * stm32_spi_write_txfifo - Write bytes in Transmit Data Register
+ * stm32f4_spi_write_tx - Write bytes to Transmit Data Register
  * @spi: pointer to the spi controller data structure
  *
  * Read from tx_buf depends on remaining bytes to avoid to read beyond
  * tx_buf end.
  */
-static void stm32_spi_write_txfifo(struct stm32_spi *spi)
+static void stm32f4_spi_write_tx(struct stm32_spi *spi)
+{
+	if ((spi->tx_len > 0) && (readl_relaxed(spi->base + STM32F4_SPI_SR) &
+				  STM32F4_SPI_SR_TXE)) {
+		u32 offs = spi->cur_xferlen - spi->tx_len;
+
+		if (spi->cur_bpw == 16) {
+			const u16 *tx_buf16 = (const u16 *)(spi->tx_buf + offs);
+
+			writew_relaxed(*tx_buf16, spi->base + STM32F4_SPI_DR);
+			spi->tx_len -= sizeof(u16);
+		} else {
+			const u8 *tx_buf8 = (const u8 *)(spi->tx_buf + offs);
+
+			writeb_relaxed(*tx_buf8, spi->base + STM32F4_SPI_DR);
+			spi->tx_len -= sizeof(u8);
+		}
+	}
+
+	dev_dbg(spi->dev, "%s: %d bytes left\n", __func__, spi->tx_len);
+}
+
+/**
+ * stm32h7_spi_write_txfifo - Write bytes in Transmit Data Register
+ * @spi: pointer to the spi controller data structure
+ *
+ * Read from tx_buf depends on remaining bytes to avoid to read beyond
+ * tx_buf end.
+ */
+static void stm32h7_spi_write_txfifo(struct stm32_spi *spi)
 {
 	while ((spi->tx_len > 0) &&
-	       (readl_relaxed(spi->base + STM32_SPI_SR) & SPI_SR_TXP)) {
+		       (readl_relaxed(spi->base + STM32H7_SPI_SR) &
+			STM32H7_SPI_SR_TXP)) {
 		u32 offs = spi->cur_xferlen - spi->tx_len;
 
 		if (spi->tx_len >= sizeof(u32)) {
 			const u32 *tx_buf32 = (const u32 *)(spi->tx_buf + offs);
 
-			writel_relaxed(*tx_buf32, spi->base + STM32_SPI_TXDR);
+			writel_relaxed(*tx_buf32, spi->base + STM32H7_SPI_TXDR);
 			spi->tx_len -= sizeof(u32);
 		} else if (spi->tx_len >= sizeof(u16)) {
 			const u16 *tx_buf16 = (const u16 *)(spi->tx_buf + offs);
 
-			writew_relaxed(*tx_buf16, spi->base + STM32_SPI_TXDR);
+			writew_relaxed(*tx_buf16, spi->base + STM32H7_SPI_TXDR);
 			spi->tx_len -= sizeof(u16);
 		} else {
 			const u8 *tx_buf8 = (const u8 *)(spi->tx_buf + offs);
 
-			writeb_relaxed(*tx_buf8, spi->base + STM32_SPI_TXDR);
+			writeb_relaxed(*tx_buf8, spi->base + STM32H7_SPI_TXDR);
 			spi->tx_len -= sizeof(u8);
 		}
 	}
@@ -340,43 +557,74 @@ static void stm32_spi_write_txfifo(struct stm32_spi *spi)
 }
 
 /**
- * stm32_spi_read_rxfifo - Read bytes in Receive Data Register
+ * stm32f4_spi_read_rx - Read bytes from Receive Data Register
+ * @spi: pointer to the spi controller data structure
+ *
+ * Write in rx_buf depends on remaining bytes to avoid to write beyond
+ * rx_buf end.
+ */
+static void stm32f4_spi_read_rx(struct stm32_spi *spi)
+{
+	if ((spi->rx_len > 0) && (readl_relaxed(spi->base + STM32F4_SPI_SR) &
+				  STM32F4_SPI_SR_RXNE)) {
+		u32 offs = spi->cur_xferlen - spi->rx_len;
+
+		if (spi->cur_bpw == 16) {
+			u16 *rx_buf16 = (u16 *)(spi->rx_buf + offs);
+
+			*rx_buf16 = readw_relaxed(spi->base + STM32F4_SPI_DR);
+			spi->rx_len -= sizeof(u16);
+		} else {
+			u8 *rx_buf8 = (u8 *)(spi->rx_buf + offs);
+
+			*rx_buf8 = readb_relaxed(spi->base + STM32F4_SPI_DR);
+			spi->rx_len -= sizeof(u8);
+		}
+	}
+
+	dev_dbg(spi->dev, "%s: %d bytes left\n", __func__, spi->rx_len);
+}
+
+/**
+ * stm32h7_spi_read_rxfifo - Read bytes in Receive Data Register
  * @spi: pointer to the spi controller data structure
  *
  * Write in rx_buf depends on remaining bytes to avoid to write beyond
  * rx_buf end.
  */
-static void stm32_spi_read_rxfifo(struct stm32_spi *spi, bool flush)
+static void stm32h7_spi_read_rxfifo(struct stm32_spi *spi, bool flush)
 {
-	u32 sr = readl_relaxed(spi->base + STM32_SPI_SR);
-	u32 rxplvl = (sr & SPI_SR_RXPLVL) >> SPI_SR_RXPLVL_SHIFT;
+	u32 sr = readl_relaxed(spi->base + STM32H7_SPI_SR);
+	u32 rxplvl = (sr & STM32H7_SPI_SR_RXPLVL) >>
+		     STM32H7_SPI_SR_RXPLVL_SHIFT;
 
 	while ((spi->rx_len > 0) &&
-	       ((sr & SPI_SR_RXP) ||
-		(flush && ((sr & SPI_SR_RXWNE) || (rxplvl > 0))))) {
+	       ((sr & STM32H7_SPI_SR_RXP) ||
+		(flush && ((sr & STM32H7_SPI_SR_RXWNE) || (rxplvl > 0))))) {
 		u32 offs = spi->cur_xferlen - spi->rx_len;
 
 		if ((spi->rx_len >= sizeof(u32)) ||
-		    (flush && (sr & SPI_SR_RXWNE))) {
+		    (flush && (sr & STM32H7_SPI_SR_RXWNE))) {
 			u32 *rx_buf32 = (u32 *)(spi->rx_buf + offs);
 
-			*rx_buf32 = readl_relaxed(spi->base + STM32_SPI_RXDR);
+			*rx_buf32 = readl_relaxed(spi->base + STM32H7_SPI_RXDR);
 			spi->rx_len -= sizeof(u32);
 		} else if ((spi->rx_len >= sizeof(u16)) ||
 			   (flush && (rxplvl >= 2 || spi->cur_bpw > 8))) {
 			u16 *rx_buf16 = (u16 *)(spi->rx_buf + offs);
 
-			*rx_buf16 = readw_relaxed(spi->base + STM32_SPI_RXDR);
+			*rx_buf16 = readw_relaxed(spi->base + STM32H7_SPI_RXDR);
 			spi->rx_len -= sizeof(u16);
 		} else {
 			u8 *rx_buf8 = (u8 *)(spi->rx_buf + offs);
 
-			*rx_buf8 = readb_relaxed(spi->base + STM32_SPI_RXDR);
+			*rx_buf8 = readb_relaxed(spi->base + STM32H7_SPI_RXDR);
 			spi->rx_len -= sizeof(u8);
 		}
 
-		sr = readl_relaxed(spi->base + STM32_SPI_SR);
-		rxplvl = (sr & SPI_SR_RXPLVL) >> SPI_SR_RXPLVL_SHIFT;
+		sr = readl_relaxed(spi->base + STM32H7_SPI_SR);
+		rxplvl = (sr & STM32H7_SPI_SR_RXPLVL) >>
+			 STM32H7_SPI_SR_RXPLVL_SHIFT;
 	}
 
 	dev_dbg(spi->dev, "%s%s: %d bytes left\n", __func__,
@@ -386,26 +634,76 @@ static void stm32_spi_read_rxfifo(struct stm32_spi *spi, bool flush)
 /**
  * stm32_spi_enable - Enable SPI controller
  * @spi: pointer to the spi controller data structure
- *
- * SPI data transfer is enabled but spi_ker_ck is idle.
- * SPI_CFG1 and SPI_CFG2 are now write protected.
  */
 static void stm32_spi_enable(struct stm32_spi *spi)
 {
 	dev_dbg(spi->dev, "enable controller\n");
 
-	stm32_spi_set_bits(spi, STM32_SPI_CR1, SPI_CR1_SPE);
+	stm32_spi_set_bits(spi, spi->cfg->regs->en.reg,
+			   spi->cfg->regs->en.mask);
 }
 
 /**
- * stm32_spi_disable - Disable SPI controller
+ * stm32f4_spi_disable - Disable SPI controller
+ * @spi: pointer to the spi controller data structure
+ */
+static void stm32f4_spi_disable(struct stm32_spi *spi)
+{
+	unsigned long flags;
+	u32 sr;
+
+	dev_dbg(spi->dev, "disable controller\n");
+
+	spin_lock_irqsave(&spi->lock, flags);
+
+	if (!(readl_relaxed(spi->base + STM32F4_SPI_CR1) &
+	      STM32F4_SPI_CR1_SPE)) {
+		spin_unlock_irqrestore(&spi->lock, flags);
+		return;
+	}
+
+	/* Disable interrupts */
+	stm32_spi_clr_bits(spi, STM32F4_SPI_CR2, STM32F4_SPI_CR2_TXEIE |
+						 STM32F4_SPI_CR2_RXNEIE |
+						 STM32F4_SPI_CR2_ERRIE);
+
+	/* Wait until BSY = 0 */
+	if (readl_relaxed_poll_timeout_atomic(spi->base + STM32F4_SPI_SR,
+					      sr, !(sr & STM32F4_SPI_SR_BSY),
+					      10, 100000) < 0) {
+		dev_warn(spi->dev, "disabling condition timeout\n");
+	}
+
+	if (spi->cur_usedma && spi->dma_tx)
+		dmaengine_terminate_all(spi->dma_tx);
+	if (spi->cur_usedma && spi->dma_rx)
+		dmaengine_terminate_all(spi->dma_rx);
+
+	stm32_spi_clr_bits(spi, STM32F4_SPI_CR1, STM32F4_SPI_CR1_SPE);
+
+	stm32_spi_clr_bits(spi, STM32F4_SPI_CR2, STM32F4_SPI_CR2_TXDMAEN |
+						 STM32F4_SPI_CR2_RXDMAEN);
+
+	/* Sequence to clear OVR flag */
+	readl_relaxed(spi->base + STM32F4_SPI_DR);
+	readl_relaxed(spi->base + STM32F4_SPI_SR);
+
+	spin_unlock_irqrestore(&spi->lock, flags);
+}
+
+/**
+ * stm32h7_spi_disable - Disable SPI controller
  * @spi: pointer to the spi controller data structure
  *
  * RX-Fifo is flushed when SPI controller is disabled. To prevent any data
- * loss, use stm32_spi_read_rxfifo(flush) to read the remaining bytes in
+ * loss, use stm32h7_spi_read_rxfifo(flush) to read the remaining bytes in
  * RX-Fifo.
+ * Normally, if TSIZE has been configured, we should relax the hardware at the
+ * reception of the EOT interrupt. But in case of error, EOT will not be
+ * raised. So the subsystem unprepare_message call allows us to properly
+ * complete the transfer from an hardware point of view.
  */
-static void stm32_spi_disable(struct stm32_spi *spi)
+static void stm32h7_spi_disable(struct stm32_spi *spi)
 {
 	unsigned long flags;
 	u32 cr1, sr;
@@ -414,23 +712,23 @@ static void stm32_spi_disable(struct stm32_spi *spi)
 
 	spin_lock_irqsave(&spi->lock, flags);
 
-	cr1 = readl_relaxed(spi->base + STM32_SPI_CR1);
+	cr1 = readl_relaxed(spi->base + STM32H7_SPI_CR1);
 
-	if (!(cr1 & SPI_CR1_SPE)) {
+	if (!(cr1 & STM32H7_SPI_CR1_SPE)) {
 		spin_unlock_irqrestore(&spi->lock, flags);
 		return;
 	}
 
 	/* Wait on EOT or suspend the flow */
-	if (readl_relaxed_poll_timeout_atomic(spi->base + STM32_SPI_SR,
-					      sr, !(sr & SPI_SR_EOT),
+	if (readl_relaxed_poll_timeout_atomic(spi->base + STM32H7_SPI_SR,
+					      sr, !(sr & STM32H7_SPI_SR_EOT),
 					      10, 100000) < 0) {
-		if (cr1 & SPI_CR1_CSTART) {
-			writel_relaxed(cr1 | SPI_CR1_CSUSP,
-				       spi->base + STM32_SPI_CR1);
+		if (cr1 & STM32H7_SPI_CR1_CSTART) {
+			writel_relaxed(cr1 | STM32H7_SPI_CR1_CSUSP,
+				       spi->base + STM32H7_SPI_CR1);
 			if (readl_relaxed_poll_timeout_atomic(
-						spi->base + STM32_SPI_SR,
-						sr, !(sr & SPI_SR_SUSP),
+						spi->base + STM32H7_SPI_SR,
+						sr, !(sr & STM32H7_SPI_SR_SUSP),
 						10, 100000) < 0)
 				dev_warn(spi->dev,
 					 "Suspend request timeout\n");
@@ -438,21 +736,21 @@ static void stm32_spi_disable(struct stm32_spi *spi)
 	}
 
 	if (!spi->cur_usedma && spi->rx_buf && (spi->rx_len > 0))
-		stm32_spi_read_rxfifo(spi, true);
+		stm32h7_spi_read_rxfifo(spi, true);
 
-	if (spi->cur_usedma && spi->tx_buf)
+	if (spi->cur_usedma && spi->dma_tx)
 		dmaengine_terminate_all(spi->dma_tx);
-	if (spi->cur_usedma && spi->rx_buf)
+	if (spi->cur_usedma && spi->dma_rx)
 		dmaengine_terminate_all(spi->dma_rx);
 
-	stm32_spi_clr_bits(spi, STM32_SPI_CR1, SPI_CR1_SPE);
+	stm32_spi_clr_bits(spi, STM32H7_SPI_CR1, STM32H7_SPI_CR1_SPE);
 
-	stm32_spi_clr_bits(spi, STM32_SPI_CFG1, SPI_CFG1_TXDMAEN |
-						SPI_CFG1_RXDMAEN);
+	stm32_spi_clr_bits(spi, STM32H7_SPI_CFG1, STM32H7_SPI_CFG1_TXDMAEN |
+						STM32H7_SPI_CFG1_RXDMAEN);
 
 	/* Disable interrupts and clear status flags */
-	writel_relaxed(0, spi->base + STM32_SPI_IER);
-	writel_relaxed(SPI_IFCR_ALL, spi->base + STM32_SPI_IFCR);
+	writel_relaxed(0, spi->base + STM32H7_SPI_IER);
+	writel_relaxed(STM32H7_SPI_IFCR_ALL, spi->base + STM32H7_SPI_IFCR);
 
 	spin_unlock_irqrestore(&spi->lock, flags);
 }
@@ -460,26 +758,136 @@ static void stm32_spi_disable(struct stm32_spi *spi)
 /**
  * stm32_spi_can_dma - Determine if the transfer is eligible for DMA use
  *
- * If the current transfer size is greater than fifo size, use DMA.
+ * If driver has fifo and the current transfer size is greater than fifo size,
+ * use DMA. Otherwise use DMA for transfer longer than defined DMA min bytes.
  */
 static bool stm32_spi_can_dma(struct spi_master *master,
 			      struct spi_device *spi_dev,
 			      struct spi_transfer *transfer)
 {
+	unsigned int dma_size;
 	struct stm32_spi *spi = spi_master_get_devdata(master);
 
+	if (spi->cfg->has_fifo)
+		dma_size = spi->fifo_size;
+	else
+		dma_size = SPI_DMA_MIN_BYTES;
+
 	dev_dbg(spi->dev, "%s: %s\n", __func__,
-		(transfer->len > spi->fifo_size) ? "true" : "false");
+		(transfer->len > dma_size) ? "true" : "false");
+
+	return (transfer->len > dma_size);
+}
+
+/**
+ * stm32f4_spi_irq_event - Interrupt handler for SPI controller events
+ * @irq: interrupt line
+ * @dev_id: SPI controller master interface
+ */
+static irqreturn_t stm32f4_spi_irq_event(int irq, void *dev_id)
+{
+	struct spi_master *master = dev_id;
+	struct stm32_spi *spi = spi_master_get_devdata(master);
+	u32 sr, mask = 0;
+	unsigned long flags;
+	bool end = false;
+
+	spin_lock_irqsave(&spi->lock, flags);
+
+	sr = readl_relaxed(spi->base + STM32F4_SPI_SR);
+	/*
+	 * BSY flag is not handled in interrupt but it is normal behavior when
+	 * this flag is set.
+	 */
+	sr &= ~STM32F4_SPI_SR_BSY;
+
+	if (!spi->cur_usedma && (spi->cur_comm == SPI_SIMPLEX_TX ||
+				 spi->cur_comm == SPI_3WIRE_TX)) {
+		/* OVR flag shouldn't be handled for TX only mode */
+		sr &= ~STM32F4_SPI_SR_OVR | STM32F4_SPI_SR_RXNE;
+		mask |= STM32F4_SPI_SR_TXE;
+	}
+
+	if (!spi->cur_usedma && spi->cur_comm == SPI_FULL_DUPLEX) {
+		/* TXE flag is set and is handled when RXNE flag occurs */
+		sr &= ~STM32F4_SPI_SR_TXE;
+		mask |= STM32F4_SPI_SR_RXNE | STM32F4_SPI_SR_OVR;
+	}
+
+	if (!(sr & mask)) {
+		dev_dbg(spi->dev, "spurious IT (sr=0x%08x)\n", sr);
+		spin_unlock_irqrestore(&spi->lock, flags);
+		return IRQ_NONE;
+	}
+
+	if (sr & STM32F4_SPI_SR_OVR) {
+		dev_warn(spi->dev, "Overrun: received value discarded\n");
+
+		/* Sequence to clear OVR flag */
+		readl_relaxed(spi->base + STM32F4_SPI_DR);
+		readl_relaxed(spi->base + STM32F4_SPI_SR);
+
+		/*
+		 * If overrun is detected, it means that something went wrong,
+		 * so stop the current transfer. Transfer can wait for next
+		 * RXNE but DR is already read and end never happens.
+		 */
+		end = true;
+		goto end_irq;
+	}
+
+	if (sr & STM32F4_SPI_SR_TXE) {
+		if (spi->tx_buf)
+			stm32f4_spi_write_tx(spi);
+		if (spi->tx_len == 0)
+			end = true;
+	}
+
+	if (sr & STM32F4_SPI_SR_RXNE) {
+		stm32f4_spi_read_rx(spi);
+		if (spi->rx_len == 0)
+			end = true;
+		else /* Load data for discontinuous mode */
+			stm32f4_spi_write_tx(spi);
+	}
+
+end_irq:
+	if (end) {
+		/* Immediately disable interrupts to do not generate new one */
+		stm32_spi_clr_bits(spi, STM32F4_SPI_CR2,
+					STM32F4_SPI_CR2_TXEIE |
+					STM32F4_SPI_CR2_RXNEIE |
+					STM32F4_SPI_CR2_ERRIE);
+		spin_unlock_irqrestore(&spi->lock, flags);
+		return IRQ_WAKE_THREAD;
+	}
+
+	spin_unlock_irqrestore(&spi->lock, flags);
+	return IRQ_HANDLED;
+}
+
+/**
+ * stm32f4_spi_irq_thread - Thread of interrupt handler for SPI controller
+ * @irq: interrupt line
+ * @dev_id: SPI controller master interface
+ */
+static irqreturn_t stm32f4_spi_irq_thread(int irq, void *dev_id)
+{
+	struct spi_master *master = dev_id;
+	struct stm32_spi *spi = spi_master_get_devdata(master);
+
+	spi_finalize_current_transfer(master);
+	stm32f4_spi_disable(spi);
 
-	return (transfer->len > spi->fifo_size);
+	return IRQ_HANDLED;
 }
 
 /**
- * stm32_spi_irq - Interrupt handler for SPI controller events
+ * stm32h7_spi_irq_thread - Thread of interrupt handler for SPI controller
  * @irq: interrupt line
  * @dev_id: SPI controller master interface
  */
-static irqreturn_t stm32_spi_irq(int irq, void *dev_id)
+static irqreturn_t stm32h7_spi_irq_thread(int irq, void *dev_id)
 {
 	struct spi_master *master = dev_id;
 	struct stm32_spi *spi = spi_master_get_devdata(master);
@@ -489,19 +897,19 @@ static irqreturn_t stm32_spi_irq(int irq, void *dev_id)
 
 	spin_lock_irqsave(&spi->lock, flags);
 
-	sr = readl_relaxed(spi->base + STM32_SPI_SR);
-	ier = readl_relaxed(spi->base + STM32_SPI_IER);
+	sr = readl_relaxed(spi->base + STM32H7_SPI_SR);
+	ier = readl_relaxed(spi->base + STM32H7_SPI_IER);
 
 	mask = ier;
 	/* EOTIE is triggered on EOT, SUSP and TXC events. */
-	mask |= SPI_SR_SUSP;
+	mask |= STM32H7_SPI_SR_SUSP;
 	/*
 	 * When TXTF is set, DXPIE and TXPIE are cleared. So in case of
 	 * Full-Duplex, need to poll RXP event to know if there are remaining
 	 * data, before disabling SPI.
 	 */
 	if (spi->rx_buf && !spi->cur_usedma)
-		mask |= SPI_SR_RXP;
+		mask |= STM32H7_SPI_SR_RXP;
 
 	if (!(sr & mask)) {
 		dev_dbg(spi->dev, "spurious IT (sr=0x%08x, ier=0x%08x)\n",
@@ -510,10 +918,10 @@ static irqreturn_t stm32_spi_irq(int irq, void *dev_id)
 		return IRQ_NONE;
 	}
 
-	if (sr & SPI_SR_SUSP) {
+	if (sr & STM32H7_SPI_SR_SUSP) {
 		dev_warn(spi->dev, "Communication suspended\n");
 		if (!spi->cur_usedma && (spi->rx_buf && (spi->rx_len > 0)))
-			stm32_spi_read_rxfifo(spi, false);
+			stm32h7_spi_read_rxfifo(spi, false);
 		/*
 		 * If communication is suspended while using DMA, it means
 		 * that something went wrong, so stop the current transfer
@@ -522,15 +930,15 @@ static irqreturn_t stm32_spi_irq(int irq, void *dev_id)
 			end = true;
 	}
 
-	if (sr & SPI_SR_MODF) {
+	if (sr & STM32H7_SPI_SR_MODF) {
 		dev_warn(spi->dev, "Mode fault: transfer aborted\n");
 		end = true;
 	}
 
-	if (sr & SPI_SR_OVR) {
+	if (sr & STM32H7_SPI_SR_OVR) {
 		dev_warn(spi->dev, "Overrun: received value discarded\n");
 		if (!spi->cur_usedma && (spi->rx_buf && (spi->rx_len > 0)))
-			stm32_spi_read_rxfifo(spi, false);
+			stm32h7_spi_read_rxfifo(spi, false);
 		/*
 		 * If overrun is detected while using DMA, it means that
 		 * something went wrong, so stop the current transfer
@@ -539,27 +947,27 @@ static irqreturn_t stm32_spi_irq(int irq, void *dev_id)
 			end = true;
 	}
 
-	if (sr & SPI_SR_EOT) {
+	if (sr & STM32H7_SPI_SR_EOT) {
 		if (!spi->cur_usedma && (spi->rx_buf && (spi->rx_len > 0)))
-			stm32_spi_read_rxfifo(spi, true);
+			stm32h7_spi_read_rxfifo(spi, true);
 		end = true;
 	}
 
-	if (sr & SPI_SR_TXP)
+	if (sr & STM32H7_SPI_SR_TXP)
 		if (!spi->cur_usedma && (spi->tx_buf && (spi->tx_len > 0)))
-			stm32_spi_write_txfifo(spi);
+			stm32h7_spi_write_txfifo(spi);
 
-	if (sr & SPI_SR_RXP)
+	if (sr & STM32H7_SPI_SR_RXP)
 		if (!spi->cur_usedma && (spi->rx_buf && (spi->rx_len > 0)))
-			stm32_spi_read_rxfifo(spi, false);
+			stm32h7_spi_read_rxfifo(spi, false);
 
-	writel_relaxed(mask, spi->base + STM32_SPI_IFCR);
+	writel_relaxed(mask, spi->base + STM32H7_SPI_IFCR);
 
 	spin_unlock_irqrestore(&spi->lock, flags);
 
 	if (end) {
 		spi_finalize_current_transfer(master);
-		stm32_spi_disable(spi);
+		stm32h7_spi_disable(spi);
 	}
 
 	return IRQ_HANDLED;
@@ -598,7 +1006,7 @@ static int stm32_spi_prepare_msg(struct spi_master *master,
 	struct spi_device *spi_dev = msg->spi;
 	struct device_node *np = spi_dev->dev.of_node;
 	unsigned long flags;
-	u32 cfg2_clrb = 0, cfg2_setb = 0;
+	u32 clrb = 0, setb = 0;
 
 	/* SPI slave device may need time between data frames */
 	spi->cur_midi = 0;
@@ -606,19 +1014,19 @@ static int stm32_spi_prepare_msg(struct spi_master *master,
 		dev_dbg(spi->dev, "%dns inter-data idleness\n", spi->cur_midi);
 
 	if (spi_dev->mode & SPI_CPOL)
-		cfg2_setb |= SPI_CFG2_CPOL;
+		setb |= spi->cfg->regs->cpol.mask;
 	else
-		cfg2_clrb |= SPI_CFG2_CPOL;
+		clrb |= spi->cfg->regs->cpol.mask;
 
 	if (spi_dev->mode & SPI_CPHA)
-		cfg2_setb |= SPI_CFG2_CPHA;
+		setb |= spi->cfg->regs->cpha.mask;
 	else
-		cfg2_clrb |= SPI_CFG2_CPHA;
+		clrb |= spi->cfg->regs->cpha.mask;
 
 	if (spi_dev->mode & SPI_LSB_FIRST)
-		cfg2_setb |= SPI_CFG2_LSBFRST;
+		setb |= spi->cfg->regs->lsb_first.mask;
 	else
-		cfg2_clrb |= SPI_CFG2_LSBFRST;
+		clrb |= spi->cfg->regs->lsb_first.mask;
 
 	dev_dbg(spi->dev, "cpol=%d cpha=%d lsb_first=%d cs_high=%d\n",
 		spi_dev->mode & SPI_CPOL,
@@ -628,11 +1036,12 @@ static int stm32_spi_prepare_msg(struct spi_master *master,
 
 	spin_lock_irqsave(&spi->lock, flags);
 
-	if (cfg2_clrb || cfg2_setb)
+	/* CPOL, CPHA and LSB FIRST bits have common register */
+	if (clrb || setb)
 		writel_relaxed(
-			(readl_relaxed(spi->base + STM32_SPI_CFG2) &
-				~cfg2_clrb) | cfg2_setb,
-			       spi->base + STM32_SPI_CFG2);
+			(readl_relaxed(spi->base + spi->cfg->regs->cpol.reg) &
+			 ~clrb) | setb,
+			spi->base + spi->cfg->regs->cpol.reg);
 
 	spin_unlock_irqrestore(&spi->lock, flags);
 
@@ -640,12 +1049,40 @@ static int stm32_spi_prepare_msg(struct spi_master *master,
 }
 
 /**
- * stm32_spi_dma_cb - dma callback
+ * stm32f4_spi_dma_tx_cb - dma callback
+ *
+ * DMA callback is called when the transfer is complete for DMA TX channel.
+ */
+static void stm32f4_spi_dma_tx_cb(void *data)
+{
+	struct stm32_spi *spi = data;
+
+	if (spi->cur_comm == SPI_SIMPLEX_TX || spi->cur_comm == SPI_3WIRE_TX) {
+		spi_finalize_current_transfer(spi->master);
+		stm32f4_spi_disable(spi);
+	}
+}
+
+/**
+ * stm32f4_spi_dma_rx_cb - dma callback
+ *
+ * DMA callback is called when the transfer is complete for DMA RX channel.
+ */
+static void stm32f4_spi_dma_rx_cb(void *data)
+{
+	struct stm32_spi *spi = data;
+
+	spi_finalize_current_transfer(spi->master);
+	stm32f4_spi_disable(spi);
+}
+
+/**
+ * stm32h7_spi_dma_cb - dma callback
  *
  * DMA callback is called when the transfer is complete or when an error
  * occurs. If the transfer is complete, EOT flag is raised.
  */
-static void stm32_spi_dma_cb(void *data)
+static void stm32h7_spi_dma_cb(void *data)
 {
 	struct stm32_spi *spi = data;
 	unsigned long flags;
@@ -653,11 +1090,11 @@ static void stm32_spi_dma_cb(void *data)
 
 	spin_lock_irqsave(&spi->lock, flags);
 
-	sr = readl_relaxed(spi->base + STM32_SPI_SR);
+	sr = readl_relaxed(spi->base + STM32H7_SPI_SR);
 
 	spin_unlock_irqrestore(&spi->lock, flags);
 
-	if (!(sr & SPI_SR_EOT))
+	if (!(sr & STM32H7_SPI_SR_EOT))
 		dev_warn(spi->dev, "DMA error (sr=0x%08x)\n", sr);
 
 	/* Now wait for EOT, or SUSP or OVR in case of error */
@@ -681,23 +1118,27 @@ static void stm32_spi_dma_config(struct stm32_spi *spi,
 	else
 		buswidth = DMA_SLAVE_BUSWIDTH_4_BYTES;
 
-	/* Valid for DMA Half or Full Fifo threshold */
-	if (spi->cur_fthlv == 2)
+	if (spi->cfg->has_fifo) {
+		/* Valid for DMA Half or Full Fifo threshold */
+		if (spi->cur_fthlv == 2)
+			maxburst = 1;
+		else
+			maxburst = spi->cur_fthlv;
+	} else {
 		maxburst = 1;
-	else
-		maxburst = spi->cur_fthlv;
+	}
 
 	memset(dma_conf, 0, sizeof(struct dma_slave_config));
 	dma_conf->direction = dir;
 	if (dma_conf->direction == DMA_DEV_TO_MEM) { /* RX */
-		dma_conf->src_addr = spi->phys_addr + STM32_SPI_RXDR;
+		dma_conf->src_addr = spi->phys_addr + spi->cfg->regs->rx.reg;
 		dma_conf->src_addr_width = buswidth;
 		dma_conf->src_maxburst = maxburst;
 
 		dev_dbg(spi->dev, "Rx DMA config buswidth=%d, maxburst=%d\n",
 			buswidth, maxburst);
 	} else if (dma_conf->direction == DMA_MEM_TO_DEV) { /* TX */
-		dma_conf->dst_addr = spi->phys_addr + STM32_SPI_TXDR;
+		dma_conf->dst_addr = spi->phys_addr + spi->cfg->regs->tx.reg;
 		dma_conf->dst_addr_width = buswidth;
 		dma_conf->dst_maxburst = maxburst;
 
@@ -707,27 +1148,68 @@ static void stm32_spi_dma_config(struct stm32_spi *spi,
 }
 
 /**
- * stm32_spi_transfer_one_irq - transfer a single spi_transfer using
- *				interrupts
+ * stm32f4_spi_transfer_one_irq - transfer a single spi_transfer using
+ *				  interrupts
  *
  * It must returns 0 if the transfer is finished or 1 if the transfer is still
  * in progress.
  */
-static int stm32_spi_transfer_one_irq(struct stm32_spi *spi)
+static int stm32f4_spi_transfer_one_irq(struct stm32_spi *spi)
+{
+	unsigned long flags;
+	u32 cr2 = 0;
+
+	/* Enable the interrupts relative to the current communication mode */
+	if (spi->cur_comm == SPI_SIMPLEX_TX || spi->cur_comm == SPI_3WIRE_TX) {
+		cr2 |= STM32F4_SPI_CR2_TXEIE;
+	} else if (spi->cur_comm == SPI_FULL_DUPLEX) {
+		/* In transmit-only mode, the OVR flag is set in the SR register
+		 * since the received data are never read. Therefore set OVR
+		 * interrupt only when rx buffer is available.
+		 */
+		cr2 |= STM32F4_SPI_CR2_RXNEIE | STM32F4_SPI_CR2_ERRIE;
+	} else {
+		return -EINVAL;
+	}
+
+	spin_lock_irqsave(&spi->lock, flags);
+
+	stm32_spi_set_bits(spi, STM32F4_SPI_CR2, cr2);
+
+	stm32_spi_enable(spi);
+
+	/* starting data transfer when buffer is loaded */
+	if (spi->tx_buf)
+		stm32f4_spi_write_tx(spi);
+
+	spin_unlock_irqrestore(&spi->lock, flags);
+
+	return 1;
+}
+
+/**
+ * stm32h7_spi_transfer_one_irq - transfer a single spi_transfer using
+ *				  interrupts
+ *
+ * It must returns 0 if the transfer is finished or 1 if the transfer is still
+ * in progress.
+ */
+static int stm32h7_spi_transfer_one_irq(struct stm32_spi *spi)
 {
 	unsigned long flags;
 	u32 ier = 0;
 
 	/* Enable the interrupts relative to the current communication mode */
 	if (spi->tx_buf && spi->rx_buf)	/* Full Duplex */
-		ier |= SPI_IER_DXPIE;
+		ier |= STM32H7_SPI_IER_DXPIE;
 	else if (spi->tx_buf)		/* Half-Duplex TX dir or Simplex TX */
-		ier |= SPI_IER_TXPIE;
+		ier |= STM32H7_SPI_IER_TXPIE;
 	else if (spi->rx_buf)		/* Half-Duplex RX dir or Simplex RX */
-		ier |= SPI_IER_RXPIE;
+		ier |= STM32H7_SPI_IER_RXPIE;
 
 	/* Enable the interrupts relative to the end of transfer */
-	ier |= SPI_IER_EOTIE | SPI_IER_TXTFIE |	SPI_IER_OVRIE |	SPI_IER_MODFIE;
+	ier |= STM32H7_SPI_IER_EOTIE | STM32H7_SPI_IER_TXTFIE |
+	       STM32H7_SPI_IER_OVRIE | STM32H7_SPI_IER_MODFIE;
 
 	spin_lock_irqsave(&spi->lock, flags);
 
@@ -735,17 +1217,54 @@ static int stm32_spi_transfer_one_irq(struct stm32_spi *spi)
 
 	/* Be sure to have data in fifo before starting data transfer */
 	if (spi->tx_buf)
-		stm32_spi_write_txfifo(spi);
+		stm32h7_spi_write_txfifo(spi);
 
-	stm32_spi_set_bits(spi, STM32_SPI_CR1, SPI_CR1_CSTART);
+	stm32_spi_set_bits(spi, STM32H7_SPI_CR1, STM32H7_SPI_CR1_CSTART);
 
-	writel_relaxed(ier, spi->base + STM32_SPI_IER);
+	writel_relaxed(ier, spi->base + STM32H7_SPI_IER);
 
 	spin_unlock_irqrestore(&spi->lock, flags);
 
 	return 1;
 }
 
+/**
+ * stm32f4_spi_transfer_one_dma_start - Set SPI driver registers to start
+ *					transfer using DMA
+ */
+static void stm32f4_spi_transfer_one_dma_start(struct stm32_spi *spi)
+{
+	/* In DMA mode end of transfer is handled by DMA TX or RX callback. */
+	if (spi->cur_comm == SPI_SIMPLEX_RX || spi->cur_comm == SPI_3WIRE_RX ||
+	    spi->cur_comm == SPI_FULL_DUPLEX) {
+		/*
+		 * In transmit-only mode, the OVR flag is set in the SR register
+		 * since the received data are never read. Therefore set OVR
+		 * interrupt only when rx buffer is available.
+		 */
+		stm32_spi_set_bits(spi, STM32F4_SPI_CR2, STM32F4_SPI_CR2_ERRIE);
+	}
+
+	stm32_spi_enable(spi);
+}
+
+/**
+ * stm32h7_spi_transfer_one_dma_start - Set SPI driver registers to start
+ *					transfer using DMA
+ */
+static void stm32h7_spi_transfer_one_dma_start(struct stm32_spi *spi)
+{
+	/* Enable the interrupts relative to the end of transfer */
+	stm32_spi_set_bits(spi, STM32H7_SPI_IER, STM32H7_SPI_IER_EOTIE |
+						 STM32H7_SPI_IER_TXTFIE |
+						 STM32H7_SPI_IER_OVRIE |
+						 STM32H7_SPI_IER_MODFIE);
+
+	stm32_spi_enable(spi);
+
+	stm32_spi_set_bits(spi, STM32H7_SPI_CR1, STM32H7_SPI_CR1_CSTART);
+}
+
 /**
  * stm32_spi_transfer_one_dma - transfer a single spi_transfer using DMA
  *
@@ -758,17 +1277,17 @@ static int stm32_spi_transfer_one_dma(struct stm32_spi *spi,
 	struct dma_slave_config tx_dma_conf, rx_dma_conf;
 	struct dma_async_tx_descriptor *tx_dma_desc, *rx_dma_desc;
 	unsigned long flags;
-	u32 ier = 0;
 
 	spin_lock_irqsave(&spi->lock, flags);
 
 	rx_dma_desc = NULL;
-	if (spi->rx_buf) {
+	if (spi->rx_buf && spi->dma_rx) {
 		stm32_spi_dma_config(spi, &rx_dma_conf, DMA_DEV_TO_MEM);
 		dmaengine_slave_config(spi->dma_rx, &rx_dma_conf);
 
 		/* Enable Rx DMA request */
-		stm32_spi_set_bits(spi, STM32_SPI_CFG1, SPI_CFG1_RXDMAEN);
+		stm32_spi_set_bits(spi, spi->cfg->regs->dma_rx_en.reg,
+				   spi->cfg->regs->dma_rx_en.mask);
 
 		rx_dma_desc = dmaengine_prep_slave_sg(
 					spi->dma_rx, xfer->rx_sg.sgl,
@@ -778,7 +1297,7 @@ static int stm32_spi_transfer_one_dma(struct stm32_spi *spi,
 	}
 
 	tx_dma_desc = NULL;
-	if (spi->tx_buf) {
+	if (spi->tx_buf && spi->dma_tx) {
 		stm32_spi_dma_config(spi, &tx_dma_conf, DMA_MEM_TO_DEV);
 		dmaengine_slave_config(spi->dma_tx, &tx_dma_conf);
 
@@ -789,12 +1308,15 @@ static int stm32_spi_transfer_one_dma(struct stm32_spi *spi,
 					DMA_PREP_INTERRUPT);
 	}
 
-	if ((spi->tx_buf && !tx_dma_desc) ||
-	    (spi->rx_buf && !rx_dma_desc))
+	if ((spi->tx_buf && spi->dma_tx && !tx_dma_desc) ||
+	    (spi->rx_buf && spi->dma_rx && !rx_dma_desc))
+		goto dma_desc_error;
+
+	if (spi->cur_comm == SPI_FULL_DUPLEX && (!tx_dma_desc || !rx_dma_desc))
 		goto dma_desc_error;
 
 	if (rx_dma_desc) {
-		rx_dma_desc->callback = stm32_spi_dma_cb;
+		rx_dma_desc->callback = spi->cfg->dma_rx_cb;
 		rx_dma_desc->callback_param = spi;
 
 		if (dma_submit_error(dmaengine_submit(rx_dma_desc))) {
@@ -806,8 +1328,9 @@ static int stm32_spi_transfer_one_dma(struct stm32_spi *spi,
 	}
 
 	if (tx_dma_desc) {
-		if (spi->cur_comm == SPI_SIMPLEX_TX) {
-			tx_dma_desc->callback = stm32_spi_dma_cb;
+		if (spi->cur_comm == SPI_SIMPLEX_TX ||
+		    spi->cur_comm == SPI_3WIRE_TX) {
+			tx_dma_desc->callback = spi->cfg->dma_tx_cb;
 			tx_dma_desc->callback_param = spi;
 		}
 
@@ -819,130 +1342,278 @@ static int stm32_spi_transfer_one_dma(struct stm32_spi *spi,
 		dma_async_issue_pending(spi->dma_tx);
 
 		/* Enable Tx DMA request */
-		stm32_spi_set_bits(spi, STM32_SPI_CFG1, SPI_CFG1_TXDMAEN);
+		stm32_spi_set_bits(spi, spi->cfg->regs->dma_tx_en.reg,
+				   spi->cfg->regs->dma_tx_en.mask);
 	}
 
-	/* Enable the interrupts relative to the end of transfer */
-	ier |= SPI_IER_EOTIE | SPI_IER_TXTFIE |	SPI_IER_OVRIE |	SPI_IER_MODFIE;
-	writel_relaxed(ier, spi->base + STM32_SPI_IER);
-
-	stm32_spi_enable(spi);
-
-	stm32_spi_set_bits(spi, STM32_SPI_CR1, SPI_CR1_CSTART);
+	spi->cfg->transfer_one_dma_start(spi);
 
 	spin_unlock_irqrestore(&spi->lock, flags);
 
 	return 1;
 
 dma_submit_error:
-	if (spi->rx_buf)
+	if (spi->dma_rx)
 		dmaengine_terminate_all(spi->dma_rx);
 
 dma_desc_error:
-	stm32_spi_clr_bits(spi, STM32_SPI_CFG1, SPI_CFG1_RXDMAEN);
+	stm32_spi_clr_bits(spi, spi->cfg->regs->dma_rx_en.reg,
+			   spi->cfg->regs->dma_rx_en.mask);
 
 	spin_unlock_irqrestore(&spi->lock, flags);
 
 	dev_info(spi->dev, "DMA issue: fall back to irq transfer\n");
 
-	return stm32_spi_transfer_one_irq(spi);
+	spi->cur_usedma = false;
+	return spi->cfg->transfer_one_irq(spi);
 }
 
 /**
- * stm32_spi_transfer_one_setup - common setup to transfer a single
- *				  spi_transfer either using DMA or
- *				  interrupts.
+ * stm32f4_spi_set_bpw - Configure bits per word
+ * @spi: pointer to the spi controller data structure
  */
-static int stm32_spi_transfer_one_setup(struct stm32_spi *spi,
-					struct spi_device *spi_dev,
-					struct spi_transfer *transfer)
+static void stm32f4_spi_set_bpw(struct stm32_spi *spi)
 {
-	unsigned long flags;
-	u32 cfg1_clrb = 0, cfg1_setb = 0, cfg2_clrb = 0, cfg2_setb = 0;
-	u32 mode, nb_words;
-	int ret = 0;
-
-	spin_lock_irqsave(&spi->lock, flags);
+	if (spi->cur_bpw == 16)
+		stm32_spi_set_bits(spi, STM32F4_SPI_CR1, STM32F4_SPI_CR1_DFF);
+	else
+		stm32_spi_clr_bits(spi, STM32F4_SPI_CR1, STM32F4_SPI_CR1_DFF);
+}
 
-	if (spi->cur_bpw != transfer->bits_per_word) {
-		u32 bpw, fthlv;
+/**
+ * stm32h7_spi_set_bpw - configure bits per word
+ * @spi: pointer to the spi controller data structure
+ */
+static void stm32h7_spi_set_bpw(struct stm32_spi *spi)
+{
+	u32 bpw, fthlv;
+	u32 cfg1_clrb = 0, cfg1_setb = 0;
 
-		spi->cur_bpw = transfer->bits_per_word;
-		bpw = spi->cur_bpw - 1;
+	bpw = spi->cur_bpw - 1;
 
-		cfg1_clrb |= SPI_CFG1_DSIZE;
-		cfg1_setb |= (bpw << SPI_CFG1_DSIZE_SHIFT) & SPI_CFG1_DSIZE;
+	cfg1_clrb |= STM32H7_SPI_CFG1_DSIZE;
+	cfg1_setb |= (bpw << STM32H7_SPI_CFG1_DSIZE_SHIFT) &
+		     STM32H7_SPI_CFG1_DSIZE;
 
-		spi->cur_fthlv = stm32_spi_prepare_fthlv(spi);
-		fthlv = spi->cur_fthlv - 1;
+	spi->cur_fthlv = stm32h7_spi_prepare_fthlv(spi);
+	fthlv = spi->cur_fthlv - 1;
 
-		cfg1_clrb |= SPI_CFG1_FTHLV;
-		cfg1_setb |= (fthlv << SPI_CFG1_FTHLV_SHIFT) & SPI_CFG1_FTHLV;
-	}
+	cfg1_clrb |= STM32H7_SPI_CFG1_FTHLV;
+	cfg1_setb |= (fthlv << STM32H7_SPI_CFG1_FTHLV_SHIFT) &
+		     STM32H7_SPI_CFG1_FTHLV;
 
-	if (spi->cur_speed != transfer->speed_hz) {
-		int mbr;
+	writel_relaxed(
+		(readl_relaxed(spi->base + STM32H7_SPI_CFG1) &
+		 ~cfg1_clrb) | cfg1_setb,
+		spi->base + STM32H7_SPI_CFG1);
+}
 
-		/* Update spi->cur_speed with real clock speed */
-		mbr = stm32_spi_prepare_mbr(spi, transfer->speed_hz);
-		if (mbr < 0) {
-			ret = mbr;
-			goto out;
-		}
+/**
+ * stm32_spi_set_mbr - Configure baud rate divisor in master mode
+ * @spi: pointer to the spi controller data structure
+ * @mbrdiv: baud rate divisor value
+ */
+static void stm32_spi_set_mbr(struct stm32_spi *spi, u32 mbrdiv)
+{
+	u32 clrb = 0, setb = 0;
 
-		transfer->speed_hz = spi->cur_speed;
+	clrb |= spi->cfg->regs->br.mask;
+	setb |= ((u32)mbrdiv << spi->cfg->regs->br.shift) &
+		spi->cfg->regs->br.mask;
 
-		cfg1_clrb |= SPI_CFG1_MBR;
-		cfg1_setb |= ((u32)mbr << SPI_CFG1_MBR_SHIFT) & SPI_CFG1_MBR;
-	}
+	writel_relaxed((readl_relaxed(spi->base + spi->cfg->regs->br.reg) &
+			~clrb) | setb,
+		       spi->base + spi->cfg->regs->br.reg);
+}
 
-	if (cfg1_clrb || cfg1_setb)
-		writel_relaxed((readl_relaxed(spi->base + STM32_SPI_CFG1) &
-				~cfg1_clrb) | cfg1_setb,
-			       spi->base + STM32_SPI_CFG1);
+/**
+ * stm32_spi_communication_type - return transfer communication type
+ * @spi_dev: pointer to the spi device
+ * transfer: pointer to spi transfer
+ */
+static unsigned int stm32_spi_communication_type(struct spi_device *spi_dev,
+						 struct spi_transfer *transfer)
+{
+	unsigned int type = SPI_FULL_DUPLEX;
 
-	mode = SPI_FULL_DUPLEX;
 	if (spi_dev->mode & SPI_3WIRE) { /* MISO/MOSI signals shared */
 		/*
 		 * SPI_3WIRE and xfer->tx_buf != NULL and xfer->rx_buf != NULL
-		 * is forbidden und unvalidated by SPI subsystem so depending
+		 * is forbidden and unvalidated by SPI subsystem so depending
 		 * on the valid buffer, we can determine the direction of the
 		 * transfer.
 		 */
-		mode = SPI_HALF_DUPLEX;
 		if (!transfer->tx_buf)
-			stm32_spi_clr_bits(spi, STM32_SPI_CR1, SPI_CR1_HDDIR);
-		else if (!transfer->rx_buf)
-			stm32_spi_set_bits(spi, STM32_SPI_CR1, SPI_CR1_HDDIR);
+			type = SPI_3WIRE_RX;
+		else
+			type = SPI_3WIRE_TX;
 	} else {
 		if (!transfer->tx_buf)
-			mode = SPI_SIMPLEX_RX;
+			type = SPI_SIMPLEX_RX;
 		else if (!transfer->rx_buf)
-			mode = SPI_SIMPLEX_TX;
+			type = SPI_SIMPLEX_TX;
+	}
+
+	return type;
+}
+
+/**
+ * stm32f4_spi_set_mode - configure communication mode
+ * @spi: pointer to the spi controller data structure
+ * @comm_type: type of communication to configure
+ */
+static int stm32f4_spi_set_mode(struct stm32_spi *spi, unsigned int comm_type)
+{
+	if (comm_type == SPI_3WIRE_TX || comm_type == SPI_SIMPLEX_TX) {
+		stm32_spi_set_bits(spi, STM32F4_SPI_CR1,
+					STM32F4_SPI_CR1_BIDIMODE |
+					STM32F4_SPI_CR1_BIDIOE);
+	} else if (comm_type == SPI_FULL_DUPLEX) {
+		stm32_spi_clr_bits(spi, STM32F4_SPI_CR1,
+					STM32F4_SPI_CR1_BIDIMODE |
+					STM32F4_SPI_CR1_BIDIOE);
+	} else {
+		return -EINVAL;
 	}
-	if (spi->cur_comm != mode) {
-		spi->cur_comm = mode;
 
-		cfg2_clrb |= SPI_CFG2_COMM;
-		cfg2_setb |= (mode << SPI_CFG2_COMM_SHIFT) & SPI_CFG2_COMM;
+	return 0;
+}
+
+/**
+ * stm32h7_spi_set_mode - configure communication mode
+ * @spi: pointer to the spi controller data structure
+ * @comm_type: type of communication to configure
+ */
+static int stm32h7_spi_set_mode(struct stm32_spi *spi, unsigned int comm_type)
+{
+	u32 mode;
+	u32 cfg2_clrb = 0, cfg2_setb = 0;
+
+	if (comm_type == SPI_3WIRE_RX) {
+		mode = STM32H7_SPI_HALF_DUPLEX;
+		stm32_spi_clr_bits(spi, STM32H7_SPI_CR1, STM32H7_SPI_CR1_HDDIR);
+	} else if (comm_type == SPI_3WIRE_TX) {
+		mode = STM32H7_SPI_HALF_DUPLEX;
+		stm32_spi_set_bits(spi, STM32H7_SPI_CR1, STM32H7_SPI_CR1_HDDIR);
+	} else if (comm_type == SPI_SIMPLEX_RX) {
+		mode = STM32H7_SPI_SIMPLEX_RX;
+	} else if (comm_type == SPI_SIMPLEX_TX) {
+		mode = STM32H7_SPI_SIMPLEX_TX;
+	} else {
+		mode = STM32H7_SPI_FULL_DUPLEX;
 	}
 
-	cfg2_clrb |= SPI_CFG2_MIDI;
-	if ((transfer->len > 1) && (spi->cur_midi > 0)) {
+	cfg2_clrb |= STM32H7_SPI_CFG2_COMM;
+	cfg2_setb |= (mode << STM32H7_SPI_CFG2_COMM_SHIFT) &
+		     STM32H7_SPI_CFG2_COMM;
+
+	writel_relaxed(
+		(readl_relaxed(spi->base + STM32H7_SPI_CFG2) &
+		 ~cfg2_clrb) | cfg2_setb,
+		spi->base + STM32H7_SPI_CFG2);
+
+	return 0;
+}
+
+/**
+ * stm32h7_spi_data_idleness - configure minimum time delay inserted between two
+ *			       consecutive data frames in master mode
+ * @spi: pointer to the spi controller data structure
+ * @len: transfer len
+ */
+static void stm32h7_spi_data_idleness(struct stm32_spi *spi, u32 len)
+{
+	u32 cfg2_clrb = 0, cfg2_setb = 0;
+
+	cfg2_clrb |= STM32H7_SPI_CFG2_MIDI;
+	if ((len > 1) && (spi->cur_midi > 0)) {
 		u32 sck_period_ns = DIV_ROUND_UP(SPI_1HZ_NS, spi->cur_speed);
 		u32 midi = min((u32)DIV_ROUND_UP(spi->cur_midi, sck_period_ns),
-			       (u32)SPI_CFG2_MIDI >> SPI_CFG2_MIDI_SHIFT);
+			       (u32)STM32H7_SPI_CFG2_MIDI >>
+			       STM32H7_SPI_CFG2_MIDI_SHIFT);
 
 		dev_dbg(spi->dev, "period=%dns, midi=%d(=%dns)\n",
 			sck_period_ns, midi, midi * sck_period_ns);
+		cfg2_setb |= (midi << STM32H7_SPI_CFG2_MIDI_SHIFT) &
+			     STM32H7_SPI_CFG2_MIDI;
+	}
+
+	writel_relaxed((readl_relaxed(spi->base + STM32H7_SPI_CFG2) &
+			~cfg2_clrb) | cfg2_setb,
+		       spi->base + STM32H7_SPI_CFG2);
+}
+
+/**
+ * stm32h7_spi_number_of_data - configure number of data at current transfer
+ * @spi: pointer to the spi controller data structure
+ * @len: transfer length
+ */
+static int stm32h7_spi_number_of_data(struct stm32_spi *spi, u32 nb_words)
+{
+	u32 cr2_clrb = 0, cr2_setb = 0;
+
+	if (nb_words <= (STM32H7_SPI_CR2_TSIZE >>
+			 STM32H7_SPI_CR2_TSIZE_SHIFT)) {
+		cr2_clrb |= STM32H7_SPI_CR2_TSIZE;
+		cr2_setb = nb_words << STM32H7_SPI_CR2_TSIZE_SHIFT;
+		writel_relaxed((readl_relaxed(spi->base + STM32H7_SPI_CR2) &
+				~cr2_clrb) | cr2_setb,
+			       spi->base + STM32H7_SPI_CR2);
+	} else {
+		return -EMSGSIZE;
+	}
+
+	return 0;
+}
+
+/**
+ * stm32_spi_transfer_one_setup - common setup to transfer a single
+ *				  spi_transfer either using DMA or
+ *				  interrupts.
+ */
+static int stm32_spi_transfer_one_setup(struct stm32_spi *spi,
+					struct spi_device *spi_dev,
+					struct spi_transfer *transfer)
+{
+	unsigned long flags;
+	unsigned int comm_type;
+	int nb_words, ret = 0;
+
+	spin_lock_irqsave(&spi->lock, flags);
+
+	if (spi->cur_bpw != transfer->bits_per_word) {
+		spi->cur_bpw = transfer->bits_per_word;
+		spi->cfg->set_bpw(spi);
+	}
 
-		cfg2_setb |= (midi << SPI_CFG2_MIDI_SHIFT) & SPI_CFG2_MIDI;
+	if (spi->cur_speed != transfer->speed_hz) {
+		int mbr;
+
+		/* Update spi->cur_speed with real clock speed */
+		mbr = stm32_spi_prepare_mbr(spi, transfer->speed_hz,
+					    spi->cfg->baud_rate_div_min,
+					    spi->cfg->baud_rate_div_max);
+		if (mbr < 0) {
+			ret = mbr;
+			goto out;
+		}
+
+		transfer->speed_hz = spi->cur_speed;
+		stm32_spi_set_mbr(spi, mbr);
 	}
 
-	if (cfg2_clrb || cfg2_setb)
-		writel_relaxed((readl_relaxed(spi->base + STM32_SPI_CFG2) &
-				~cfg2_clrb) | cfg2_setb,
-			       spi->base + STM32_SPI_CFG2);
+	comm_type = stm32_spi_communication_type(spi_dev, transfer);
+	if (spi->cur_comm != comm_type) {
+		ret = spi->cfg->set_mode(spi, comm_type);
+
+		if (ret < 0)
+			goto out;
+
+		spi->cur_comm = comm_type;
+	}
+
+	if (spi->cfg->set_data_idleness)
+		spi->cfg->set_data_idleness(spi, transfer->len);
 
 	if (spi->cur_bpw <= 8)
 		nb_words = transfer->len;
@@ -950,13 +1621,11 @@ static int stm32_spi_transfer_one_setup(struct stm32_spi *spi,
 		nb_words = DIV_ROUND_UP(transfer->len * 8, 16);
 	else
 		nb_words = DIV_ROUND_UP(transfer->len * 8, 32);
-	nb_words <<= SPI_CR2_TSIZE_SHIFT;
 
-	if (nb_words <= SPI_CR2_TSIZE) {
-		writel_relaxed(nb_words, spi->base + STM32_SPI_CR2);
-	} else {
-		ret = -EMSGSIZE;
-		goto out;
+	if (spi->cfg->set_number_of_data) {
+		ret = spi->cfg->set_number_of_data(spi, nb_words);
+		if (ret < 0)
+			goto out;
 	}
 
 	spi->cur_xferlen = transfer->len;
@@ -997,7 +1666,7 @@ static int stm32_spi_transfer_one(struct spi_master *master,
 	spi->rx_len = spi->rx_buf ? transfer->len : 0;
 
 	spi->cur_usedma = (master->can_dma &&
-			   stm32_spi_can_dma(master, spi_dev, transfer));
+			   master->can_dma(master, spi_dev, transfer));
 
 	ret = stm32_spi_transfer_one_setup(spi, spi_dev, transfer);
 	if (ret) {
@@ -1008,47 +1677,73 @@ static int stm32_spi_transfer_one(struct spi_master *master,
 	if (spi->cur_usedma)
 		return stm32_spi_transfer_one_dma(spi, transfer);
 	else
-		return stm32_spi_transfer_one_irq(spi);
+		return spi->cfg->transfer_one_irq(spi);
 }
 
 /**
  * stm32_spi_unprepare_msg - relax the hardware
- *
- * Normally, if TSIZE has been configured, we should relax the hardware at the
- * reception of the EOT interrupt. But in case of error, EOT will not be
- * raised. So the subsystem unprepare_message call allows us to properly
- * complete the transfer from an hardware point of view.
  */
 static int stm32_spi_unprepare_msg(struct spi_master *master,
 				   struct spi_message *msg)
 {
 	struct stm32_spi *spi = spi_master_get_devdata(master);
 
-	stm32_spi_disable(spi);
+	spi->cfg->disable(spi);
+
+	return 0;
+}
+
+/**
+ * stm32f4_spi_config - Configure SPI controller as SPI master
+ */
+static int stm32f4_spi_config(struct stm32_spi *spi)
+{
+	unsigned long flags;
+
+	spin_lock_irqsave(&spi->lock, flags);
+
+	/* Ensure I2SMOD bit is kept cleared */
+	stm32_spi_clr_bits(spi, STM32F4_SPI_I2SCFGR,
+			   STM32F4_SPI_I2SCFGR_I2SMOD);
+
+	/*
+	 * - SS input value high
+	 * - transmitter half duplex direction
+	 * - Set the master mode (default Motorola mode)
+	 * - Consider 1 master/n slaves configuration and
+	 *   SS input value is determined by the SSI bit
+	 */
+	stm32_spi_set_bits(spi, STM32F4_SPI_CR1, STM32F4_SPI_CR1_SSI |
+						 STM32F4_SPI_CR1_BIDIOE |
+						 STM32F4_SPI_CR1_MSTR |
+						 STM32F4_SPI_CR1_SSM);
+
+	spin_unlock_irqrestore(&spi->lock, flags);
 
 	return 0;
 }
 
 /**
- * stm32_spi_config - Configure SPI controller as SPI master
+ * stm32h7_spi_config - Configure SPI controller as SPI master
  */
-static int stm32_spi_config(struct stm32_spi *spi)
+static int stm32h7_spi_config(struct stm32_spi *spi)
 {
 	unsigned long flags;
 
 	spin_lock_irqsave(&spi->lock, flags);
 
 	/* Ensure I2SMOD bit is kept cleared */
-	stm32_spi_clr_bits(spi, STM32_SPI_I2SCFGR, SPI_I2SCFGR_I2SMOD);
+	stm32_spi_clr_bits(spi, STM32H7_SPI_I2SCFGR,
+			   STM32H7_SPI_I2SCFGR_I2SMOD);
 
 	/*
 	 * - SS input value high
 	 * - transmitter half duplex direction
 	 * - automatic communication suspend when RX-Fifo is full
 	 */
-	stm32_spi_set_bits(spi, STM32_SPI_CR1, SPI_CR1_SSI |
-					       SPI_CR1_HDDIR |
-					       SPI_CR1_MASRX);
+	stm32_spi_set_bits(spi, STM32H7_SPI_CR1, STM32H7_SPI_CR1_SSI |
+						 STM32H7_SPI_CR1_HDDIR |
+						 STM32H7_SPI_CR1_MASRX);
 
 	/*
 	 * - Set the master mode (default Motorola mode)
@@ -1056,17 +1751,56 @@ static int stm32_spi_config(struct stm32_spi *spi)
 	 *   SS input value is determined by the SSI bit
 	 * - keep control of all associated GPIOs
 	 */
-	stm32_spi_set_bits(spi, STM32_SPI_CFG2, SPI_CFG2_MASTER |
-						SPI_CFG2_SSM |
-						SPI_CFG2_AFCNTR);
+	stm32_spi_set_bits(spi, STM32H7_SPI_CFG2, STM32H7_SPI_CFG2_MASTER |
+						  STM32H7_SPI_CFG2_SSM |
+						  STM32H7_SPI_CFG2_AFCNTR);
 
 	spin_unlock_irqrestore(&spi->lock, flags);
 
 	return 0;
 }
 
+static const struct stm32_spi_cfg stm32f4_spi_cfg = {
+	.regs = &stm32f4_spi_regspec,
+	.get_bpw_mask = stm32f4_spi_get_bpw_mask,
+	.disable = stm32f4_spi_disable,
+	.config = stm32f4_spi_config,
+	.set_bpw = stm32f4_spi_set_bpw,
+	.set_mode = stm32f4_spi_set_mode,
+	.transfer_one_dma_start = stm32f4_spi_transfer_one_dma_start,
+	.dma_tx_cb = stm32f4_spi_dma_tx_cb,
+	.dma_rx_cb = stm32f4_spi_dma_rx_cb,
+	.transfer_one_irq = stm32f4_spi_transfer_one_irq,
+	.irq_handler_event = stm32f4_spi_irq_event,
+	.irq_handler_thread = stm32f4_spi_irq_thread,
+	.baud_rate_div_min = STM32F4_SPI_BR_DIV_MIN,
+	.baud_rate_div_max = STM32F4_SPI_BR_DIV_MAX,
+	.has_fifo = false,
+};
+
+static const struct stm32_spi_cfg stm32h7_spi_cfg = {
+	.regs = &stm32h7_spi_regspec,
+	.get_fifo_size = stm32h7_spi_get_fifo_size,
+	.get_bpw_mask = stm32h7_spi_get_bpw_mask,
+	.disable = stm32h7_spi_disable,
+	.config = stm32h7_spi_config,
+	.set_bpw = stm32h7_spi_set_bpw,
+	.set_mode = stm32h7_spi_set_mode,
+	.set_data_idleness = stm32h7_spi_data_idleness,
+	.set_number_of_data = stm32h7_spi_number_of_data,
+	.transfer_one_dma_start = stm32h7_spi_transfer_one_dma_start,
+	.dma_rx_cb = stm32h7_spi_dma_cb,
+	.dma_tx_cb = stm32h7_spi_dma_cb,
+	.transfer_one_irq = stm32h7_spi_transfer_one_irq,
+	.irq_handler_thread = stm32h7_spi_irq_thread,
+	.baud_rate_div_min = STM32H7_SPI_MBR_DIV_MIN,
+	.baud_rate_div_max = STM32H7_SPI_MBR_DIV_MAX,
+	.has_fifo = true,
+};
+
 static const struct of_device_id stm32_spi_of_match[] = {
-	{ .compatible = "st,stm32h7-spi", },
+	{ .compatible = "st,stm32h7-spi", .data = (void *)&stm32h7_spi_cfg },
+	{ .compatible = "st,stm32f4-spi", .data = (void *)&stm32f4_spi_cfg },
 	{},
 };
 MODULE_DEVICE_TABLE(of, stm32_spi_of_match);
@@ -1090,12 +1824,17 @@ static int stm32_spi_probe(struct platform_device *pdev)
 	spi->master = master;
 	spin_lock_init(&spi->lock);
 
+	spi->cfg = (const struct stm32_spi_cfg *)
+		of_match_device(pdev->dev.driver->of_match_table,
+				&pdev->dev)->data;
+
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	spi->base = devm_ioremap_resource(&pdev->dev, res);
 	if (IS_ERR(spi->base)) {
 		ret = PTR_ERR(spi->base);
 		goto err_master_put;
 	}
+
 	spi->phys_addr = (dma_addr_t)res->start;
 
 	spi->irq = platform_get_irq(pdev, 0);
@@ -1104,16 +1843,17 @@ static int stm32_spi_probe(struct platform_device *pdev)
 		ret = -ENOENT;
 		goto err_master_put;
 	}
-	ret = devm_request_threaded_irq(&pdev->dev, spi->irq, NULL,
-					stm32_spi_irq, IRQF_ONESHOT,
-					pdev->name, master);
+	ret = devm_request_threaded_irq(&pdev->dev, spi->irq,
+					spi->cfg->irq_handler_event,
+					spi->cfg->irq_handler_thread,
+					IRQF_ONESHOT, pdev->name, master);
 	if (ret) {
 		dev_err(&pdev->dev, "irq%d request failed: %d\n", spi->irq,
 			ret);
 		goto err_master_put;
 	}
 
-	spi->clk = devm_clk_get(&pdev->dev, 0);
+	spi->clk = devm_clk_get(&pdev->dev, NULL);
 	if (IS_ERR(spi->clk)) {
 		ret = PTR_ERR(spi->clk);
 		dev_err(&pdev->dev, "clk get failed: %d\n", ret);
@@ -1139,9 +1879,10 @@ static int stm32_spi_probe(struct platform_device *pdev)
 		reset_control_deassert(spi->rst);
 	}
 
-	spi->fifo_size = stm32_spi_get_fifo_size(spi);
+	if (spi->cfg->has_fifo)
+		spi->fifo_size = spi->cfg->get_fifo_size(spi);
 
-	ret = stm32_spi_config(spi);
+	ret = spi->cfg->config(spi);
 	if (ret) {
 		dev_err(&pdev->dev, "controller configuration failed: %d\n",
 			ret);
@@ -1151,11 +1892,11 @@ static int stm32_spi_probe(struct platform_device *pdev)
 	master->dev.of_node = pdev->dev.of_node;
 	master->auto_runtime_pm = true;
 	master->bus_num = pdev->id;
-	master->mode_bits = SPI_MODE_3 | SPI_CS_HIGH | SPI_LSB_FIRST |
-			    SPI_3WIRE | SPI_LOOP;
-	master->bits_per_word_mask = stm32_spi_get_bpw_mask(spi);
-	master->max_speed_hz = spi->clk_rate / SPI_MBR_DIV_MIN;
-	master->min_speed_hz = spi->clk_rate / SPI_MBR_DIV_MAX;
+	master->mode_bits = SPI_CPHA | SPI_CPOL | SPI_CS_HIGH | SPI_LSB_FIRST |
+			    SPI_3WIRE;
+	master->bits_per_word_mask = spi->cfg->get_bpw_mask(spi);
+	master->max_speed_hz = spi->clk_rate / spi->cfg->baud_rate_div_min;
+	master->min_speed_hz = spi->clk_rate / spi->cfg->baud_rate_div_max;
 	master->setup = stm32_spi_setup;
 	master->prepare_message = stm32_spi_prepare_msg;
 	master->transfer_one = stm32_spi_transfer_one;
@@ -1233,7 +1974,7 @@ static int stm32_spi_remove(struct platform_device *pdev)
 	struct spi_master *master = platform_get_drvdata(pdev);
 	struct stm32_spi *spi = spi_master_get_devdata(master);
 
-	stm32_spi_disable(spi);
+	spi->cfg->disable(spi);
 
 	if (master->dma_tx)
 		dma_release_channel(master->dma_tx);
diff --git a/drivers/spi/spi-ti-qspi.c b/drivers/spi/spi-ti-qspi.c
index 5f19016bbf10..b9fb6493cd6b 100644
--- a/drivers/spi/spi-ti-qspi.c
+++ b/drivers/spi/spi-ti-qspi.c
@@ -490,8 +490,8 @@ static void ti_qspi_enable_memory_map(struct spi_device *spi)
 	ti_qspi_write(qspi, MM_SWITCH, QSPI_SPI_SWITCH_REG);
 	if (qspi->ctrl_base) {
 		regmap_update_bits(qspi->ctrl_base, qspi->ctrl_reg,
-				   MEM_CS_EN(spi->chip_select),
-				   MEM_CS_MASK);
+				   MEM_CS_MASK,
+				   MEM_CS_EN(spi->chip_select));
 	}
 	qspi->mmap_enabled = true;
 }
@@ -503,7 +503,7 @@ static void ti_qspi_disable_memory_map(struct spi_device *spi)
 	ti_qspi_write(qspi, 0, QSPI_SPI_SWITCH_REG);
 	if (qspi->ctrl_base)
 		regmap_update_bits(qspi->ctrl_base, qspi->ctrl_reg,
-				   0, MEM_CS_MASK);
+				   MEM_CS_MASK, 0);
 	qspi->mmap_enabled = false;
 }
 
diff --git a/drivers/spi/spi-topcliff-pch.c b/drivers/spi/spi-topcliff-pch.c
index 97d137591b18..e7e8ea1edcce 100644
--- a/drivers/spi/spi-topcliff-pch.c
+++ b/drivers/spi/spi-topcliff-pch.c
@@ -1008,6 +1008,9 @@ static void pch_spi_handle_dma(struct pch_spi_data *data, int *bpw)
 
 	/* RX */
 	dma->sg_rx_p = kcalloc(num, sizeof(*dma->sg_rx_p), GFP_ATOMIC);
+	if (!dma->sg_rx_p)
+		return;
+
 	sg_init_table(dma->sg_rx_p, num); /* Initialize SG table */
 	/* offset, length setting */
 	sg = dma->sg_rx_p;
@@ -1068,6 +1071,9 @@ static void pch_spi_handle_dma(struct pch_spi_data *data, int *bpw)
 	}
 
 	dma->sg_tx_p = kcalloc(num, sizeof(*dma->sg_tx_p), GFP_ATOMIC);
+	if (!dma->sg_tx_p)
+		return;
+
 	sg_init_table(dma->sg_tx_p, num); /* Initialize SG table */
 	/* offset, length setting */
 	sg = dma->sg_tx_p;
diff --git a/drivers/spi/spi.c b/drivers/spi/spi.c
index 9a7def7c3237..93986f879b09 100644
--- a/drivers/spi/spi.c
+++ b/drivers/spi/spi.c
@@ -19,6 +19,7 @@
 #include <linux/spi/spi.h>
 #include <linux/spi/spi-mem.h>
 #include <linux/of_gpio.h>
+#include <linux/gpio/consumer.h>
 #include <linux/pm_runtime.h>
 #include <linux/pm_domain.h>
 #include <linux/property.h>
@@ -578,7 +579,10 @@ int spi_add_device(struct spi_device *spi)
 		goto done;
 	}
 
-	if (ctlr->cs_gpios)
+	/* Descriptors take precedence */
+	if (ctlr->cs_gpiods)
+		spi->cs_gpiod = ctlr->cs_gpiods[spi->chip_select];
+	else if (ctlr->cs_gpios)
 		spi->cs_gpio = ctlr->cs_gpios[spi->chip_select];
 
 	/* Drivers may modify this initial i/o setup, but will
@@ -772,10 +776,21 @@ static void spi_set_cs(struct spi_device *spi, bool enable)
 	if (spi->mode & SPI_CS_HIGH)
 		enable = !enable;
 
-	if (gpio_is_valid(spi->cs_gpio)) {
-		/* Honour the SPI_NO_CS flag */
-		if (!(spi->mode & SPI_NO_CS))
-			gpio_set_value(spi->cs_gpio, !enable);
+	if (spi->cs_gpiod || gpio_is_valid(spi->cs_gpio)) {
+		/*
+		 * Honour the SPI_NO_CS flag and invert the enable line, as
+		 * active low is default for SPI. Execution paths that handle
+		 * polarity inversion in gpiolib (such as device tree) will
+		 * enforce active high using the SPI_CS_HIGH resulting in a
+		 * double inversion through the code above.
+		 */
+		if (!(spi->mode & SPI_NO_CS)) {
+			if (spi->cs_gpiod)
+				gpiod_set_value_cansleep(spi->cs_gpiod,
+							 !enable);
+			else
+				gpio_set_value_cansleep(spi->cs_gpio, !enable);
+		}
 		/* Some SPI masters need both GPIO CS & slave_select */
 		if ((spi->controller->flags & SPI_MASTER_GPIO_SS) &&
 		    spi->controller->set_cs)
@@ -1615,13 +1630,21 @@ static int of_spi_parse_dt(struct spi_controller *ctlr, struct spi_device *spi,
 		spi->mode |= SPI_CPHA;
 	if (of_property_read_bool(nc, "spi-cpol"))
 		spi->mode |= SPI_CPOL;
-	if (of_property_read_bool(nc, "spi-cs-high"))
-		spi->mode |= SPI_CS_HIGH;
 	if (of_property_read_bool(nc, "spi-3wire"))
 		spi->mode |= SPI_3WIRE;
 	if (of_property_read_bool(nc, "spi-lsb-first"))
 		spi->mode |= SPI_LSB_FIRST;
 
+	/*
+	 * For descriptors associated with the device, polarity inversion is
+	 * handled in the gpiolib, so all chip selects are "active high" in
+	 * the logical sense, the gpiolib will invert the line if need be.
+	 */
+	if (ctlr->use_gpio_descriptors)
+		spi->mode |= SPI_CS_HIGH;
+	else if (of_property_read_bool(nc, "spi-cs-high"))
+		spi->mode |= SPI_CS_HIGH;
+
 	/* Device DUAL/QUAD mode */
 	if (!of_property_read_u32(nc, "spi-tx-bus-width", &value)) {
 		switch (value) {
@@ -2137,6 +2160,60 @@ static int of_spi_register_master(struct spi_controller *ctlr)
 }
 #endif
 
+/**
+ * spi_get_gpio_descs() - grab chip select GPIOs for the master
+ * @ctlr: The SPI master to grab GPIO descriptors for
+ */
+static int spi_get_gpio_descs(struct spi_controller *ctlr)
+{
+	int nb, i;
+	struct gpio_desc **cs;
+	struct device *dev = &ctlr->dev;
+
+	nb = gpiod_count(dev, "cs");
+	ctlr->num_chipselect = max_t(int, nb, ctlr->num_chipselect);
+
+	/* No GPIOs at all is fine, else return the error */
+	if (nb == 0 || nb == -ENOENT)
+		return 0;
+	else if (nb < 0)
+		return nb;
+
+	cs = devm_kcalloc(dev, ctlr->num_chipselect, sizeof(*cs),
+			  GFP_KERNEL);
+	if (!cs)
+		return -ENOMEM;
+	ctlr->cs_gpiods = cs;
+
+	for (i = 0; i < nb; i++) {
+		/*
+		 * Most chipselects are active low, the inverted
+		 * semantics are handled by special quirks in gpiolib,
+		 * so initializing them GPIOD_OUT_LOW here means
+		 * "unasserted", in most cases this will drive the physical
+		 * line high.
+		 */
+		cs[i] = devm_gpiod_get_index_optional(dev, "cs", i,
+						      GPIOD_OUT_LOW);
+
+		if (cs[i]) {
+			/*
+			 * If we find a CS GPIO, name it after the device and
+			 * chip select line.
+			 */
+			char *gpioname;
+
+			gpioname = devm_kasprintf(dev, GFP_KERNEL, "%s CS%d",
+						  dev_name(dev), i);
+			if (!gpioname)
+				return -ENOMEM;
+			gpiod_set_consumer_name(cs[i], gpioname);
+		}
+	}
+
+	return 0;
+}
+
 static int spi_controller_check_ops(struct spi_controller *ctlr)
 {
 	/*
@@ -2199,9 +2276,21 @@ int spi_register_controller(struct spi_controller *ctlr)
 		return status;
 
 	if (!spi_controller_is_slave(ctlr)) {
-		status = of_spi_register_master(ctlr);
-		if (status)
-			return status;
+		if (ctlr->use_gpio_descriptors) {
+			status = spi_get_gpio_descs(ctlr);
+			if (status)
+				return status;
+			/*
+			 * A controller using GPIO descriptors always
+			 * supports SPI_CS_HIGH if need be.
+			 */
+			ctlr->mode_bits |= SPI_CS_HIGH;
+		} else {
+			/* Legacy code path for GPIOs from DT */
+			status = of_spi_register_master(ctlr);
+			if (status)
+				return status;
+		}
 	}
 
 	/* even if it's just one always-selected device, there must
@@ -2915,6 +3004,7 @@ static int __spi_validate(struct spi_device *spi, struct spi_message *message)
 	 * cs_change is set for each transfer.
 	 */
 	if ((spi->mode & SPI_CS_WORD) && (!(ctlr->mode_bits & SPI_CS_WORD) ||
+					  spi->cs_gpiod ||
 					  gpio_is_valid(spi->cs_gpio))) {
 		size_t maxsize;
 		int ret;
@@ -2961,6 +3051,8 @@ static int __spi_validate(struct spi_device *spi, struct spi_message *message)
 	 * it is not set for this transfer.
 	 * Set transfer tx_nbits and rx_nbits as single transfer default
 	 * (SPI_NBITS_SINGLE) if it is not set for this transfer.
+	 * Ensure transfer word_delay is at least as long as that required by
+	 * device itself.
 	 */
 	message->frame_length = 0;
 	list_for_each_entry(xfer, &message->transfers, transfer_list) {
@@ -3031,6 +3123,9 @@ static int __spi_validate(struct spi_device *spi, struct spi_message *message)
 				!(spi->mode & SPI_RX_QUAD))
 				return -EINVAL;
 		}
+
+		if (xfer->word_delay_usecs < spi->word_delay_usecs)
+			xfer->word_delay_usecs = spi->word_delay_usecs;
 	}
 
 	message->status = -EINPROGRESS;
diff --git a/drivers/spi/spidev.c b/drivers/spi/spidev.c
index b0c76e2626ce..70966e10be7e 100644
--- a/drivers/spi/spidev.c
+++ b/drivers/spi/spidev.c
@@ -276,17 +276,19 @@ static int spidev_message(struct spidev_data *spidev,
 		k_tmp->bits_per_word = u_tmp->bits_per_word;
 		k_tmp->delay_usecs = u_tmp->delay_usecs;
 		k_tmp->speed_hz = u_tmp->speed_hz;
+		k_tmp->word_delay_usecs = u_tmp->word_delay_usecs;
 		if (!k_tmp->speed_hz)
 			k_tmp->speed_hz = spidev->speed_hz;
 #ifdef VERBOSE
 		dev_dbg(&spidev->spi->dev,
-			"  xfer len %u %s%s%s%dbits %u usec %uHz\n",
+			"  xfer len %u %s%s%s%dbits %u usec %u usec %uHz\n",
 			u_tmp->len,
 			u_tmp->rx_buf ? "rx " : "",
 			u_tmp->tx_buf ? "tx " : "",
 			u_tmp->cs_change ? "cs " : "",
 			u_tmp->bits_per_word ? : spidev->spi->bits_per_word,
 			u_tmp->delay_usecs,
+			u_tmp->word_delay_usecs,
 			u_tmp->speed_hz ? : spidev->spi->max_speed_hz);
 #endif
 		spi_message_add_tail(k_tmp, &msg);
diff --git a/drivers/tty/serial/max310x.c b/drivers/tty/serial/max310x.c
index 4f479841769a..305086b8208a 100644
--- a/drivers/tty/serial/max310x.c
+++ b/drivers/tty/serial/max310x.c
@@ -248,6 +248,7 @@
 struct max310x_devtype {
 	char	name[9];
 	int	nr;
+	u8	mode1;
 	int	(*detect)(struct device *);
 	void	(*power)(struct uart_port *, int);
 };
@@ -410,6 +411,7 @@ static void max14830_power(struct uart_port *port, int on)
 static const struct max310x_devtype max3107_devtype = {
 	.name	= "MAX3107",
 	.nr	= 1,
+	.mode1	= MAX310X_MODE1_AUTOSLEEP_BIT | MAX310X_MODE1_IRQSEL_BIT,
 	.detect	= max3107_detect,
 	.power	= max310x_power,
 };
@@ -417,6 +419,7 @@ static const struct max310x_devtype max3107_devtype = {
 static const struct max310x_devtype max3108_devtype = {
 	.name	= "MAX3108",
 	.nr	= 1,
+	.mode1	= MAX310X_MODE1_AUTOSLEEP_BIT,
 	.detect	= max3108_detect,
 	.power	= max310x_power,
 };
@@ -424,6 +427,7 @@ static const struct max310x_devtype max3108_devtype = {
 static const struct max310x_devtype max3109_devtype = {
 	.name	= "MAX3109",
 	.nr	= 2,
+	.mode1	= MAX310X_MODE1_AUTOSLEEP_BIT,
 	.detect	= max3109_detect,
 	.power	= max310x_power,
 };
@@ -431,6 +435,7 @@ static const struct max310x_devtype max3109_devtype = {
 static const struct max310x_devtype max14830_devtype = {
 	.name	= "MAX14830",
 	.nr	= 4,
+	.mode1	= MAX310X_MODE1_IRQSEL_BIT,
 	.detect	= max14830_detect,
 	.power	= max14830_power,
 };
@@ -1197,8 +1202,7 @@ static int max310x_probe(struct device *dev, struct max310x_devtype *devtype,
 		return PTR_ERR(regmap);
 
 	/* Alloc port structure */
-	s = devm_kzalloc(dev, sizeof(*s) +
-			 sizeof(struct max310x_one) * devtype->nr, GFP_KERNEL);
+	s = devm_kzalloc(dev, struct_size(s, p, devtype->nr), GFP_KERNEL);
 	if (!s) {
 		dev_err(dev, "Error allocating port structure\n");
 		return -ENOMEM;
@@ -1258,9 +1262,8 @@ static int max310x_probe(struct device *dev, struct max310x_devtype *devtype,
 				    MAX310X_BRGDIVLSB_REG + offs, &ret);
 		} while (ret != 0x01);
 
-		regmap_update_bits(s->regmap, MAX310X_MODE1_REG + offs,
-				   MAX310X_MODE1_AUTOSLEEP_BIT,
-				   MAX310X_MODE1_AUTOSLEEP_BIT);
+		regmap_write(s->regmap, MAX310X_MODE1_REG + offs,
+			     devtype->mode1);
 	}
 
 	uartclk = max310x_set_ref_clk(dev, s, freq, xtal);
@@ -1294,10 +1297,6 @@ static int max310x_probe(struct device *dev, struct max310x_devtype *devtype,
 		max310x_port_write(&s->p[i].port, MAX310X_IRQEN_REG, 0);
 		/* Clear IRQ status register */
 		max310x_port_read(&s->p[i].port, MAX310X_IRQSTS_REG);
-		/* Enable IRQ pin */
-		max310x_port_update(&s->p[i].port, MAX310X_MODE1_REG,
-				    MAX310X_MODE1_IRQSEL_BIT,
-				    MAX310X_MODE1_IRQSEL_BIT);
 		/* Initialize queue for start TX */
 		INIT_WORK(&s->p[i].tx_work, max310x_wq_proc);
 		/* Initialize queue for changing LOOPBACK mode */
diff --git a/include/linux/gpio/driver.h b/include/linux/gpio/driver.h
index 07cddbf45186..92a222646447 100644
--- a/include/linux/gpio/driver.h
+++ b/include/linux/gpio/driver.h
@@ -609,6 +609,9 @@ struct gpio_desc *gpiochip_request_own_desc(struct gpio_chip *chip, u16 hwnum,
 					    enum gpiod_flags flags);
 void gpiochip_free_own_desc(struct gpio_desc *desc);
 
+void devprop_gpiochip_set_names(struct gpio_chip *chip,
+				const struct fwnode_handle *fwnode);
+
 #else /* CONFIG_GPIOLIB */
 
 static inline struct gpio_chip *gpiod_to_chip(const struct gpio_desc *desc)
diff --git a/include/linux/platform_data/spi-ath79.h b/include/linux/platform_data/spi-ath79.h
new file mode 100644
index 000000000000..aa71216edf99
--- /dev/null
+++ b/include/linux/platform_data/spi-ath79.h
@@ -0,0 +1,19 @@
+/*
+ *  Platform data definition for Atheros AR71XX/AR724X/AR913X SPI controller
+ *
+ *  Copyright (C) 2008-2010 Gabor Juhos <juhosg@openwrt.org>
+ *
+ *  This program is free software; you can redistribute it and/or modify it
+ *  under the terms of the GNU General Public License version 2 as published
+ *  by the Free Software Foundation.
+ */
+
+#ifndef _ATH79_SPI_PLATFORM_H
+#define _ATH79_SPI_PLATFORM_H
+
+struct ath79_spi_platform_data {
+	unsigned	bus_num;
+	unsigned	num_chipselect;
+};
+
+#endif /* _ATH79_SPI_PLATFORM_H */
diff --git a/include/linux/spi/pxa2xx_spi.h b/include/linux/spi/pxa2xx_spi.h
index b0674e330ef6..c1c59473cef9 100644
--- a/include/linux/spi/pxa2xx_spi.h
+++ b/include/linux/spi/pxa2xx_spi.h
@@ -22,7 +22,7 @@
 struct dma_chan;
 
 /* device.platform_data for SSP controller devices */
-struct pxa2xx_spi_master {
+struct pxa2xx_spi_controller {
 	u16 num_chipselect;
 	u8 enable_dma;
 	bool is_slave;
@@ -54,7 +54,7 @@ struct pxa2xx_spi_chip {
 
 #include <linux/clk.h>
 
-extern void pxa2xx_set_spi_info(unsigned id, struct pxa2xx_spi_master *info);
+extern void pxa2xx_set_spi_info(unsigned id, struct pxa2xx_spi_controller *info);
 
 #endif
 #endif
diff --git a/include/linux/spi/spi-mem.h b/include/linux/spi/spi-mem.h
index 3fe24500c5ee..3703d0dcac2e 100644
--- a/include/linux/spi/spi-mem.h
+++ b/include/linux/spi/spi-mem.h
@@ -330,6 +330,11 @@ ssize_t spi_mem_dirmap_read(struct spi_mem_dirmap_desc *desc,
 			    u64 offs, size_t len, void *buf);
 ssize_t spi_mem_dirmap_write(struct spi_mem_dirmap_desc *desc,
 			     u64 offs, size_t len, const void *buf);
+struct spi_mem_dirmap_desc *
+devm_spi_mem_dirmap_create(struct device *dev, struct spi_mem *mem,
+			   const struct spi_mem_dirmap_info *info);
+void devm_spi_mem_dirmap_destroy(struct device *dev,
+				 struct spi_mem_dirmap_desc *desc);
 
 int spi_mem_driver_register_with_owner(struct spi_mem_driver *drv,
 				       struct module *owner);
diff --git a/include/linux/spi/spi.h b/include/linux/spi/spi.h
index 314d922ca607..662b336aa2e4 100644
--- a/include/linux/spi/spi.h
+++ b/include/linux/spi/spi.h
@@ -12,6 +12,7 @@
 #include <linux/kthread.h>
 #include <linux/completion.h>
 #include <linux/scatterlist.h>
+#include <linux/gpio/consumer.h>
 
 struct dma_chan;
 struct property_entry;
@@ -116,8 +117,13 @@ void spi_statistics_add_transfer_stats(struct spi_statistics *stats,
  * @modalias: Name of the driver to use with this device, or an alias
  *	for that name.  This appears in the sysfs "modalias" attribute
  *	for driver coldplugging, and in uevents used for hotplugging
- * @cs_gpio: gpio number of the chipselect line (optional, -ENOENT when
+ * @cs_gpio: LEGACY: gpio number of the chipselect line (optional, -ENOENT when
+ *	not using a GPIO line) use cs_gpiod in new drivers by opting in on
+ *	the spi_master.
+ * @cs_gpiod: gpio descriptor of the chipselect line (optional, NULL when
  *	not using a GPIO line)
+ * @word_delay_usecs: microsecond delay to be inserted between consecutive
+ *	words of a transfer
  *
  * @statistics: statistics for the spi_device
  *
@@ -163,7 +169,9 @@ struct spi_device {
 	void			*controller_data;
 	char			modalias[SPI_NAME_SIZE];
 	const char		*driver_override;
-	int			cs_gpio;	/* chip select gpio */
+	int			cs_gpio;	/* LEGACY: chip select gpio */
+	struct gpio_desc	*cs_gpiod;	/* chip select gpio desc */
+	uint8_t			word_delay_usecs; /* inter-word delay */
 
 	/* the statistics */
 	struct spi_statistics	statistics;
@@ -376,9 +384,17 @@ static inline void spi_unregister_driver(struct spi_driver *sdrv)
  *	     controller has native support for memory like operations.
  * @unprepare_message: undo any work done by prepare_message().
  * @slave_abort: abort the ongoing transfer request on an SPI slave controller
- * @cs_gpios: Array of GPIOs to use as chip select lines; one per CS
- *	number. Any individual value may be -ENOENT for CS lines that
+ * @cs_gpios: LEGACY: array of GPIO descs to use as chip select lines; one per
+ *	CS number. Any individual value may be -ENOENT for CS lines that
+ *	are not GPIOs (driven by the SPI controller itself). Use the cs_gpiods
+ *	in new drivers.
+ * @cs_gpiods: Array of GPIO descs to use as chip select lines; one per CS
+ *	number. Any individual value may be NULL for CS lines that
  *	are not GPIOs (driven by the SPI controller itself).
+ * @use_gpio_descriptors: Turns on the code in the SPI core to parse and grab
+ *	GPIO descriptors rather than using global GPIO numbers grabbed by the
+ *	driver. This will fill in @cs_gpiods and @cs_gpios should not be used,
+ *	and SPI devices will have the cs_gpiod assigned rather than cs_gpio.
  * @statistics: statistics for the spi_controller
  * @dma_tx: DMA transmit channel
  * @dma_rx: DMA receive channel
@@ -557,6 +573,8 @@ struct spi_controller {
 
 	/* gpio chip select */
 	int			*cs_gpios;
+	struct gpio_desc	**cs_gpiods;
+	bool			use_gpio_descriptors;
 
 	/* statistics */
 	struct spi_statistics	statistics;
@@ -706,6 +724,8 @@ extern void spi_res_release(struct spi_controller *ctlr,
  * @delay_usecs: microseconds to delay after this transfer before
  *	(optionally) changing the chipselect status, then starting
  *	the next transfer or completing this @spi_message.
+ * @word_delay_usecs: microseconds to inter word delay after each word size
+ *	(set by bits_per_word) transmission.
  * @word_delay: clock cycles to inter word delay after each word size
  *	(set by bits_per_word) transmission.
  * @transfer_list: transfers are sequenced through @spi_message.transfers
@@ -788,6 +808,7 @@ struct spi_transfer {
 #define	SPI_NBITS_DUAL		0x02 /* 2bits transfer */
 #define	SPI_NBITS_QUAD		0x04 /* 4bits transfer */
 	u8		bits_per_word;
+	u8		word_delay_usecs;
 	u16		delay_usecs;
 	u32		speed_hz;
 	u16		word_delay;
diff --git a/include/trace/events/spi.h b/include/trace/events/spi.h
index 277bb9d25779..aef6869f563d 100644
--- a/include/trace/events/spi.h
+++ b/include/trace/events/spi.h
@@ -109,6 +109,16 @@ TRACE_EVENT(spi_message_done,
                   (unsigned)__entry->actual, (unsigned)__entry->frame)
 );
 
+/*
+ * consider a buffer valid if non-NULL and if it doesn't match the dummy buffer
+ * that only exist to work with controllers that have SPI_CONTROLLER_MUST_TX or
+ * SPI_CONTROLLER_MUST_RX.
+ */
+#define spi_valid_txbuf(msg, xfer) \
+	(xfer->tx_buf && xfer->tx_buf != msg->spi->controller->dummy_tx)
+#define spi_valid_rxbuf(msg, xfer) \
+	(xfer->rx_buf && xfer->rx_buf != msg->spi->controller->dummy_rx)
+
 DECLARE_EVENT_CLASS(spi_transfer,
 
 	TP_PROTO(struct spi_message *msg, struct spi_transfer *xfer),
@@ -120,6 +130,10 @@ DECLARE_EVENT_CLASS(spi_transfer,
 		__field(        int,            chip_select     )
 		__field(        struct spi_transfer *,   xfer   )
 		__field(        int,            len             )
+		__dynamic_array(u8, rx_buf,
+				spi_valid_rxbuf(msg, xfer) ? xfer->len : 0)
+		__dynamic_array(u8, tx_buf,
+				spi_valid_txbuf(msg, xfer) ? xfer->len : 0)
 	),
 
 	TP_fast_assign(
@@ -127,12 +141,21 @@ DECLARE_EVENT_CLASS(spi_transfer,
 		__entry->chip_select = msg->spi->chip_select;
 		__entry->xfer = xfer;
 		__entry->len = xfer->len;
+
+		if (spi_valid_txbuf(msg, xfer))
+			memcpy(__get_dynamic_array(tx_buf),
+			       xfer->tx_buf, xfer->len);
+
+		if (spi_valid_rxbuf(msg, xfer))
+			memcpy(__get_dynamic_array(rx_buf),
+			       xfer->rx_buf, xfer->len);
 	),
 
-        TP_printk("spi%d.%d %p len=%d", (int)__entry->bus_num,
-		  (int)__entry->chip_select,
-		  (struct spi_message *)__entry->xfer,
-		  (int)__entry->len)
+	TP_printk("spi%d.%d %p len=%d tx=[%*phD] rx=[%*phD]",
+		  __entry->bus_num, __entry->chip_select,
+		  __entry->xfer, __entry->len,
+		  __get_dynamic_array_len(tx_buf), __get_dynamic_array(tx_buf),
+		  __get_dynamic_array_len(rx_buf), __get_dynamic_array(rx_buf))
 );
 
 DEFINE_EVENT(spi_transfer, spi_transfer_start,
diff --git a/include/uapi/linux/spi/spidev.h b/include/uapi/linux/spi/spidev.h
index c4253f0090d8..ee0f2460bff6 100644
--- a/include/uapi/linux/spi/spidev.h
+++ b/include/uapi/linux/spi/spidev.h
@@ -66,6 +66,9 @@
  * @delay_usecs: If nonzero, how long to delay after the last bit transfer
  *	before optionally deselecting the device before the next transfer.
  * @cs_change: True to deselect device before starting the next transfer.
+ * @word_delay_usecs: If nonzero, how long to wait between words within one
+ *	transfer. This property needs explicit support in the SPI controller,
+ *	otherwise it is silently ignored.
  *
  * This structure is mapped directly to the kernel spi_transfer structure;
  * the fields have the same meanings, except of course that the pointers
@@ -100,7 +103,8 @@ struct spi_ioc_transfer {
 	__u8		cs_change;
 	__u8		tx_nbits;
 	__u8		rx_nbits;
-	__u16		pad;
+	__u8		word_delay_usecs;
+	__u8		pad;
 
 	/* If the contents of 'struct spi_ioc_transfer' ever change
 	 * incompatibly, then the ioctl number (currently 0) must change;