blob: 42d4f0d15cc71d3fcdab4f6c90088ff51401b112 [file] [log] [blame]
#include "armada-388-clearfog-base.dts"
&w25q32 {
status = "okay";
};
/ {
clocks {
spi_uart_clk: osc_max14830 {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <3686400>;
};
};
soc {
internal-regs {
sdhci@d8000 {
/delete-property/ cd-gpios;
broken-cd;
};
};
};
gpio_i2c {
compatible = "i2c-gpio";
sda-gpios = <&gpio0 25 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
scl-gpios = <&gpio0 24 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
i2c-gpio.delay-us = <1>;
#address-cells = <1>;
#size-cells = <0>;
};
gpio-leds {
compatible = "gpio-leds";
ok_led {
label = "status-ok";
linux,default-trigger = "default-on";
gpios = <&max14830 9 GPIO_ACTIVE_HIGH>;
};
fail_led {
label = "status-error";
panic-indicator;
gpios = <&max14830 8 GPIO_ACTIVE_HIGH>;
};
uid_led {
label = "UID";
linux,default-trigger = "heartbeat";
gpios = <&max14830 10 GPIO_ACTIVE_HIGH>;
};
};
};
&uart1_pins {
status = "disabled";
};
&uart1 {
status = "disabled";
};
&gpio1 {
spi_int {
/* MPP54: this needs an external pull-up */
gpio-hog;
gpios = <22 GPIO_ACTIVE_HIGH>;
input;
line-name = "SPI-INT";
};
};
&spi1 {
cs-gpios = <0>, <&gpio0 22 GPIO_ACTIVE_HIGH>, <0>, <&gpio0 29 GPIO_ACTIVE_HIGH>;
max14830: max14830@2 {
compatible = "maxim,max14830";
reg = <2>;
clocks = <&spi_uart_clk>;
clock-names = "xtal";
interrupt-parent = <&gpio1>;
interrupts = <22 IRQ_TYPE_LEVEL_LOW>;
gpio-controller;
#gpio-cells = <2>;
spi-max-frequency = <26000000>;
gpio-line-names =
"WSS_HWRST",
"WSS_SSD",
"OCM_HS_IN",
"OCM_RESET",
"WSS_MRST",
"I2C_XOR_ENABLE",
"I2C_XORH",
"I2C_BB_ENABLE",
"LED_RED",
"LED_GREEN",
"LED_BLUE",
"EDFA1_AMPLIFIER_DISABLE",
"EDFA2_AMPLIFIER_DISABLE",
"EDFA1_OUTPUT_POWER_MUTE",
"EDFA2_OUTPUT_POWER_MUTE",
"" /* not used, not routed anywhere */
;
};
gpio_spi_chips: gpio@1 {
compatible = "microchip,mcp23s17";
reg = <1>;
interrupt-parent = <&gpio1>;
interrupts = <22 IRQ_TYPE_LEVEL_LOW>;
interrupt-controller;
#interrupt-cells = <2>;
gpio-controller;
#gpio-cells = <2>;
microchip,spi-present-mask = <0x06>; /* extra addresses 1 and 2 */
microchip,irq-mirror;
drive-open-drain;
spi-max-frequency = <10000000>;
// FIXME: this naming is incompatible with that hack which makes these devices visible as 2*16pin standalone chips
gpio-bank@1 {
address = <1>;
gpio-line-names =
"EDFA1_RESET",
"EDFA2_RESET",
"PMB_ALERT",
"ATX_TTL", /* FIXME: will this be used? */
"WSS_SC",
"WSS_RST",
"I2C_XOR_RDY",
"OCM_HS_OUT",
"EDFA1_OUT_REFLECTION_ALARM",
"EDFA1_PUMP_CURRENT_ALARM",
"EDFA1_ST1_IN_LOS_ALARM",
"EDFA1_ST2_IN_LOS_ALARM",
"EDFA1_ST2_OUT_GAIN_ALARM",
"EDFA1_CASE_TEMP_ALARM",
"EDFA1_ST1_OUT_GAIN_ALARM",
"EDFA1_PUMP_TEMP_ALARM";
};
gpio-bank@2 {
address = <2>;
gpio-line-names =
/* these are all grounded */
"GND",
"GND",
"GND",
"GND",
"GND",
"GND",
"GND",
"GND",
"EDFA2_OUT_REFLECTION_ALARM",
"EDFA2_PUMP_CURRENT_ALARM",
"EDFA2_ST1_IN_LOS_ALARM",
"EDFA2_ST2_IN_LOS_ALARM",
"EDFA2_ST2_OUT_GAIN_ALARM",
"EDFA2_CASE_TEMP_ALARM",
"EDFA2_ST1_OUT_GAIN_ALARM",
"EDFA2_PUMP_TEMP_ALARM";
};
};
spidev@3 {
compatible = "spidev";
reg = <3>;
spi-max-frequency = <12000000>;
// The SPI slave is CPOL=1, but the rest of the devices is CPOL=0 and our SPI master
// appears to have troubles with CPOL=1 toggling -> let's use a physical inverter
linux,spi-wdelay = /bits/ 16 <3>;
};
};
&i2c1 {
eeprom@57 {
compatible = "atmel,24c128";
reg = <0x57>;
pagesize = <64>;
};
/* ADT7463: it doesn't use the DT */
};