blob: ed3b27e6e7590a4869edd948f7bd99dedb15229c [file] [log] [blame]
Simon Glasse9be1ee2016-05-01 11:36:10 -06001/*
2 * (C) Copyright 2000-2011
3 * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
4 *
5 * SPDX-License-Identifier: GPL-2.0+
6 */
7
8#include <common.h>
9#include <ata.h>
Simon Glass145df842016-05-01 11:36:22 -060010#include <dm.h>
Simon Glasse9be1ee2016-05-01 11:36:10 -060011#include <ide.h>
12#include <watchdog.h>
13#include <asm/io.h>
14
15#ifdef __PPC__
16# define EIEIO __asm__ volatile ("eieio")
17# define SYNC __asm__ volatile ("sync")
18#else
19# define EIEIO /* nothing */
20# define SYNC /* nothing */
21#endif
22
23/* Current offset for IDE0 / IDE1 bus access */
24ulong ide_bus_offset[CONFIG_SYS_IDE_MAXBUS] = {
25#if defined(CONFIG_SYS_ATA_IDE0_OFFSET)
26 CONFIG_SYS_ATA_IDE0_OFFSET,
27#endif
28#if defined(CONFIG_SYS_ATA_IDE1_OFFSET) && (CONFIG_SYS_IDE_MAXBUS > 1)
29 CONFIG_SYS_ATA_IDE1_OFFSET,
30#endif
31};
32
33static int ide_bus_ok[CONFIG_SYS_IDE_MAXBUS];
34
35struct blk_desc ide_dev_desc[CONFIG_SYS_IDE_MAXDEVICE];
36
37#define IDE_TIME_OUT 2000 /* 2 sec timeout */
38
39#define ATAPI_TIME_OUT 7000 /* 7 sec timeout (5 sec seems to work...) */
40
41#define IDE_SPIN_UP_TIME_OUT 5000 /* 5 sec spin-up timeout */
42
43#ifndef CONFIG_SYS_ATA_PORT_ADDR
44#define CONFIG_SYS_ATA_PORT_ADDR(port) (port)
45#endif
46
Simon Glasse9be1ee2016-05-01 11:36:10 -060047#ifdef CONFIG_IDE_RESET
48extern void ide_set_reset(int idereset);
49
50static void ide_reset(void)
51{
52 int i;
53
54 for (i = 0; i < CONFIG_SYS_IDE_MAXBUS; ++i)
55 ide_bus_ok[i] = 0;
56 for (i = 0; i < CONFIG_SYS_IDE_MAXDEVICE; ++i)
57 ide_dev_desc[i].type = DEV_TYPE_UNKNOWN;
58
59 ide_set_reset(1); /* assert reset */
60
61 /* the reset signal shall be asserted for et least 25 us */
62 udelay(25);
63
64 WATCHDOG_RESET();
65
66 /* de-assert RESET signal */
67 ide_set_reset(0);
68
69 /* wait 250 ms */
70 for (i = 0; i < 250; ++i)
71 udelay(1000);
72}
73#else
74#define ide_reset() /* dummy */
75#endif /* CONFIG_IDE_RESET */
76
77/*
78 * Wait until Busy bit is off, or timeout (in ms)
79 * Return last status
80 */
81static uchar ide_wait(int dev, ulong t)
82{
83 ulong delay = 10 * t; /* poll every 100 us */
84 uchar c;
85
86 while ((c = ide_inb(dev, ATA_STATUS)) & ATA_STAT_BUSY) {
87 udelay(100);
88 if (delay-- == 0)
89 break;
90 }
91 return c;
92}
93
94/*
95 * copy src to dest, skipping leading and trailing blanks and null
96 * terminate the string
97 * "len" is the size of available memory including the terminating '\0'
98 */
99static void ident_cpy(unsigned char *dst, unsigned char *src,
100 unsigned int len)
101{
102 unsigned char *end, *last;
103
104 last = dst;
105 end = src + len - 1;
106
107 /* reserve space for '\0' */
108 if (len < 2)
109 goto OUT;
110
111 /* skip leading white space */
112 while ((*src) && (src < end) && (*src == ' '))
113 ++src;
114
115 /* copy string, omitting trailing white space */
116 while ((*src) && (src < end)) {
117 *dst++ = *src;
118 if (*src++ != ' ')
119 last = dst;
120 }
121OUT:
122 *last = '\0';
123}
124
125#ifdef CONFIG_ATAPI
126/****************************************************************************
127 * ATAPI Support
128 */
129
130#if defined(CONFIG_IDE_SWAP_IO)
131/* since ATAPI may use commands with not 4 bytes alligned length
132 * we have our own transfer functions, 2 bytes alligned */
133__weak void ide_output_data_shorts(int dev, ushort *sect_buf, int shorts)
134{
135 ushort *dbuf;
136 volatile ushort *pbuf;
137
138 pbuf = (ushort *)(ATA_CURR_BASE(dev) + ATA_DATA_REG);
139 dbuf = (ushort *)sect_buf;
140
141 debug("in output data shorts base for read is %lx\n",
142 (unsigned long) pbuf);
143
144 while (shorts--) {
145 EIEIO;
146 *pbuf = *dbuf++;
147 }
148}
149
150__weak void ide_input_data_shorts(int dev, ushort *sect_buf, int shorts)
151{
152 ushort *dbuf;
153 volatile ushort *pbuf;
154
155 pbuf = (ushort *)(ATA_CURR_BASE(dev) + ATA_DATA_REG);
156 dbuf = (ushort *)sect_buf;
157
158 debug("in input data shorts base for read is %lx\n",
159 (unsigned long) pbuf);
160
161 while (shorts--) {
162 EIEIO;
163 *dbuf++ = *pbuf;
164 }
165}
166
167#else /* ! CONFIG_IDE_SWAP_IO */
168__weak void ide_output_data_shorts(int dev, ushort *sect_buf, int shorts)
169{
170 outsw(ATA_CURR_BASE(dev) + ATA_DATA_REG, sect_buf, shorts);
171}
172
173__weak void ide_input_data_shorts(int dev, ushort *sect_buf, int shorts)
174{
175 insw(ATA_CURR_BASE(dev) + ATA_DATA_REG, sect_buf, shorts);
176}
177
178#endif /* CONFIG_IDE_SWAP_IO */
179
180/*
181 * Wait until (Status & mask) == res, or timeout (in ms)
182 * Return last status
183 * This is used since some ATAPI CD ROMs clears their Busy Bit first
184 * and then they set their DRQ Bit
185 */
186static uchar atapi_wait_mask(int dev, ulong t, uchar mask, uchar res)
187{
188 ulong delay = 10 * t; /* poll every 100 us */
189 uchar c;
190
191 /* prevents to read the status before valid */
192 c = ide_inb(dev, ATA_DEV_CTL);
193
194 while (((c = ide_inb(dev, ATA_STATUS)) & mask) != res) {
195 /* break if error occurs (doesn't make sense to wait more) */
196 if ((c & ATA_STAT_ERR) == ATA_STAT_ERR)
197 break;
198 udelay(100);
199 if (delay-- == 0)
200 break;
201 }
202 return c;
203}
204
205/*
206 * issue an atapi command
207 */
208unsigned char atapi_issue(int device, unsigned char *ccb, int ccblen,
209 unsigned char *buffer, int buflen)
210{
211 unsigned char c, err, mask, res;
212 int n;
213
Simon Glasse9be1ee2016-05-01 11:36:10 -0600214 /* Select device
215 */
216 mask = ATA_STAT_BUSY | ATA_STAT_DRQ;
217 res = 0;
218 ide_outb(device, ATA_DEV_HD, ATA_LBA | ATA_DEVICE(device));
219 c = atapi_wait_mask(device, ATAPI_TIME_OUT, mask, res);
220 if ((c & mask) != res) {
221 printf("ATAPI_ISSUE: device %d not ready status %X\n", device,
222 c);
223 err = 0xFF;
224 goto AI_OUT;
225 }
226 /* write taskfile */
227 ide_outb(device, ATA_ERROR_REG, 0); /* no DMA, no overlaped */
228 ide_outb(device, ATA_SECT_CNT, 0);
229 ide_outb(device, ATA_SECT_NUM, 0);
230 ide_outb(device, ATA_CYL_LOW, (unsigned char) (buflen & 0xFF));
231 ide_outb(device, ATA_CYL_HIGH,
232 (unsigned char) ((buflen >> 8) & 0xFF));
233 ide_outb(device, ATA_DEV_HD, ATA_LBA | ATA_DEVICE(device));
234
235 ide_outb(device, ATA_COMMAND, ATAPI_CMD_PACKET);
236 udelay(50);
237
238 mask = ATA_STAT_DRQ | ATA_STAT_BUSY | ATA_STAT_ERR;
239 res = ATA_STAT_DRQ;
240 c = atapi_wait_mask(device, ATAPI_TIME_OUT, mask, res);
241
242 if ((c & mask) != res) { /* DRQ must be 1, BSY 0 */
243 printf("ATAPI_ISSUE: Error (no IRQ) before sending ccb dev %d status 0x%02x\n",
244 device, c);
245 err = 0xFF;
246 goto AI_OUT;
247 }
248
249 /* write command block */
250 ide_output_data_shorts(device, (unsigned short *)ccb, ccblen / 2);
251
252 /* ATAPI Command written wait for completition */
253 udelay(5000); /* device must set bsy */
254
255 mask = ATA_STAT_DRQ | ATA_STAT_BUSY | ATA_STAT_ERR;
256 /*
257 * if no data wait for DRQ = 0 BSY = 0
258 * if data wait for DRQ = 1 BSY = 0
259 */
260 res = 0;
261 if (buflen)
262 res = ATA_STAT_DRQ;
263 c = atapi_wait_mask(device, ATAPI_TIME_OUT, mask, res);
264 if ((c & mask) != res) {
265 if (c & ATA_STAT_ERR) {
266 err = (ide_inb(device, ATA_ERROR_REG)) >> 4;
267 debug("atapi_issue 1 returned sense key %X status %02X\n",
268 err, c);
269 } else {
270 printf("ATAPI_ISSUE: (no DRQ) after sending ccb (%x) status 0x%02x\n",
271 ccb[0], c);
272 err = 0xFF;
273 }
274 goto AI_OUT;
275 }
276 n = ide_inb(device, ATA_CYL_HIGH);
277 n <<= 8;
278 n += ide_inb(device, ATA_CYL_LOW);
279 if (n > buflen) {
280 printf("ERROR, transfer bytes %d requested only %d\n", n,
281 buflen);
282 err = 0xff;
283 goto AI_OUT;
284 }
285 if ((n == 0) && (buflen < 0)) {
286 printf("ERROR, transfer bytes %d requested %d\n", n, buflen);
287 err = 0xff;
288 goto AI_OUT;
289 }
290 if (n != buflen) {
291 debug("WARNING, transfer bytes %d not equal with requested %d\n",
292 n, buflen);
293 }
294 if (n != 0) { /* data transfer */
295 debug("ATAPI_ISSUE: %d Bytes to transfer\n", n);
296 /* we transfer shorts */
297 n >>= 1;
298 /* ok now decide if it is an in or output */
299 if ((ide_inb(device, ATA_SECT_CNT) & 0x02) == 0) {
300 debug("Write to device\n");
301 ide_output_data_shorts(device, (unsigned short *)buffer,
302 n);
303 } else {
304 debug("Read from device @ %p shorts %d\n", buffer, n);
305 ide_input_data_shorts(device, (unsigned short *)buffer,
306 n);
307 }
308 }
309 udelay(5000); /* seems that some CD ROMs need this... */
310 mask = ATA_STAT_BUSY | ATA_STAT_ERR;
311 res = 0;
312 c = atapi_wait_mask(device, ATAPI_TIME_OUT, mask, res);
313 if ((c & ATA_STAT_ERR) == ATA_STAT_ERR) {
314 err = (ide_inb(device, ATA_ERROR_REG) >> 4);
315 debug("atapi_issue 2 returned sense key %X status %X\n", err,
316 c);
317 } else {
318 err = 0;
319 }
320AI_OUT:
Simon Glasse9be1ee2016-05-01 11:36:10 -0600321 return err;
322}
323
324/*
325 * sending the command to atapi_issue. If an status other than good
326 * returns, an request_sense will be issued
327 */
328
329#define ATAPI_DRIVE_NOT_READY 100
330#define ATAPI_UNIT_ATTN 10
331
332unsigned char atapi_issue_autoreq(int device,
333 unsigned char *ccb,
334 int ccblen,
335 unsigned char *buffer, int buflen)
336{
337 unsigned char sense_data[18], sense_ccb[12];
338 unsigned char res, key, asc, ascq;
339 int notready, unitattn;
340
341 unitattn = ATAPI_UNIT_ATTN;
342 notready = ATAPI_DRIVE_NOT_READY;
343
344retry:
345 res = atapi_issue(device, ccb, ccblen, buffer, buflen);
346 if (res == 0)
347 return 0; /* Ok */
348
349 if (res == 0xFF)
350 return 0xFF; /* error */
351
352 debug("(auto_req)atapi_issue returned sense key %X\n", res);
353
354 memset(sense_ccb, 0, sizeof(sense_ccb));
355 memset(sense_data, 0, sizeof(sense_data));
356 sense_ccb[0] = ATAPI_CMD_REQ_SENSE;
357 sense_ccb[4] = 18; /* allocation Length */
358
359 res = atapi_issue(device, sense_ccb, 12, sense_data, 18);
360 key = (sense_data[2] & 0xF);
361 asc = (sense_data[12]);
362 ascq = (sense_data[13]);
363
364 debug("ATAPI_CMD_REQ_SENSE returned %x\n", res);
365 debug(" Sense page: %02X key %02X ASC %02X ASCQ %02X\n",
366 sense_data[0], key, asc, ascq);
367
368 if ((key == 0))
369 return 0; /* ok device ready */
370
371 if ((key == 6) || (asc == 0x29) || (asc == 0x28)) { /* Unit Attention */
372 if (unitattn-- > 0) {
373 udelay(200 * 1000);
374 goto retry;
375 }
376 printf("Unit Attention, tried %d\n", ATAPI_UNIT_ATTN);
377 goto error;
378 }
379 if ((asc == 0x4) && (ascq == 0x1)) {
380 /* not ready, but will be ready soon */
381 if (notready-- > 0) {
382 udelay(200 * 1000);
383 goto retry;
384 }
385 printf("Drive not ready, tried %d times\n",
386 ATAPI_DRIVE_NOT_READY);
387 goto error;
388 }
389 if (asc == 0x3a) {
390 debug("Media not present\n");
391 goto error;
392 }
393
394 printf("ERROR: Unknown Sense key %02X ASC %02X ASCQ %02X\n", key, asc,
395 ascq);
396error:
397 debug("ERROR Sense key %02X ASC %02X ASCQ %02X\n", key, asc, ascq);
398 return 0xFF;
399}
400
401/*
402 * atapi_read:
403 * we transfer only one block per command, since the multiple DRQ per
404 * command is not yet implemented
405 */
406#define ATAPI_READ_MAX_BYTES 2048 /* we read max 2kbytes */
407#define ATAPI_READ_BLOCK_SIZE 2048 /* assuming CD part */
408#define ATAPI_READ_MAX_BLOCK (ATAPI_READ_MAX_BYTES/ATAPI_READ_BLOCK_SIZE)
409
410ulong atapi_read(struct blk_desc *block_dev, lbaint_t blknr, lbaint_t blkcnt,
411 void *buffer)
412{
413 int device = block_dev->devnum;
414 ulong n = 0;
415 unsigned char ccb[12]; /* Command descriptor block */
416 ulong cnt;
417
418 debug("atapi_read dev %d start " LBAF " blocks " LBAF
419 " buffer at %lX\n", device, blknr, blkcnt, (ulong) buffer);
420
421 do {
422 if (blkcnt > ATAPI_READ_MAX_BLOCK)
423 cnt = ATAPI_READ_MAX_BLOCK;
424 else
425 cnt = blkcnt;
426
427 ccb[0] = ATAPI_CMD_READ_12;
428 ccb[1] = 0; /* reserved */
429 ccb[2] = (unsigned char) (blknr >> 24) & 0xFF; /* MSB Block */
430 ccb[3] = (unsigned char) (blknr >> 16) & 0xFF; /* */
431 ccb[4] = (unsigned char) (blknr >> 8) & 0xFF;
432 ccb[5] = (unsigned char) blknr & 0xFF; /* LSB Block */
433 ccb[6] = (unsigned char) (cnt >> 24) & 0xFF; /* MSB Block cnt */
434 ccb[7] = (unsigned char) (cnt >> 16) & 0xFF;
435 ccb[8] = (unsigned char) (cnt >> 8) & 0xFF;
436 ccb[9] = (unsigned char) cnt & 0xFF; /* LSB Block */
437 ccb[10] = 0; /* reserved */
438 ccb[11] = 0; /* reserved */
439
440 if (atapi_issue_autoreq(device, ccb, 12,
441 (unsigned char *)buffer,
442 cnt * ATAPI_READ_BLOCK_SIZE)
443 == 0xFF) {
444 return n;
445 }
446 n += cnt;
447 blkcnt -= cnt;
448 blknr += cnt;
449 buffer += (cnt * ATAPI_READ_BLOCK_SIZE);
450 } while (blkcnt > 0);
451 return n;
452}
453
454static void atapi_inquiry(struct blk_desc *dev_desc)
455{
456 unsigned char ccb[12]; /* Command descriptor block */
457 unsigned char iobuf[64]; /* temp buf */
458 unsigned char c;
459 int device;
460
461 device = dev_desc->devnum;
462 dev_desc->type = DEV_TYPE_UNKNOWN; /* not yet valid */
Bin Meng52a1c2c2017-07-30 19:24:00 -0700463#ifndef CONFIG_BLK
Simon Glasse9be1ee2016-05-01 11:36:10 -0600464 dev_desc->block_read = atapi_read;
Bin Meng52a1c2c2017-07-30 19:24:00 -0700465#endif
Simon Glasse9be1ee2016-05-01 11:36:10 -0600466
467 memset(ccb, 0, sizeof(ccb));
468 memset(iobuf, 0, sizeof(iobuf));
469
470 ccb[0] = ATAPI_CMD_INQUIRY;
471 ccb[4] = 40; /* allocation Legnth */
472 c = atapi_issue_autoreq(device, ccb, 12, (unsigned char *)iobuf, 40);
473
474 debug("ATAPI_CMD_INQUIRY returned %x\n", c);
475 if (c != 0)
476 return;
477
478 /* copy device ident strings */
479 ident_cpy((unsigned char *)dev_desc->vendor, &iobuf[8], 8);
480 ident_cpy((unsigned char *)dev_desc->product, &iobuf[16], 16);
481 ident_cpy((unsigned char *)dev_desc->revision, &iobuf[32], 5);
482
483 dev_desc->lun = 0;
484 dev_desc->lba = 0;
485 dev_desc->blksz = 0;
486 dev_desc->log2blksz = LOG2_INVALID(typeof(dev_desc->log2blksz));
487 dev_desc->type = iobuf[0] & 0x1f;
488
489 if ((iobuf[1] & 0x80) == 0x80)
490 dev_desc->removable = 1;
491 else
492 dev_desc->removable = 0;
493
494 memset(ccb, 0, sizeof(ccb));
495 memset(iobuf, 0, sizeof(iobuf));
496 ccb[0] = ATAPI_CMD_START_STOP;
497 ccb[4] = 0x03; /* start */
498
499 c = atapi_issue_autoreq(device, ccb, 12, (unsigned char *)iobuf, 0);
500
501 debug("ATAPI_CMD_START_STOP returned %x\n", c);
502 if (c != 0)
503 return;
504
505 memset(ccb, 0, sizeof(ccb));
506 memset(iobuf, 0, sizeof(iobuf));
507 c = atapi_issue_autoreq(device, ccb, 12, (unsigned char *)iobuf, 0);
508
509 debug("ATAPI_CMD_UNIT_TEST_READY returned %x\n", c);
510 if (c != 0)
511 return;
512
513 memset(ccb, 0, sizeof(ccb));
514 memset(iobuf, 0, sizeof(iobuf));
515 ccb[0] = ATAPI_CMD_READ_CAP;
516 c = atapi_issue_autoreq(device, ccb, 12, (unsigned char *)iobuf, 8);
517 debug("ATAPI_CMD_READ_CAP returned %x\n", c);
518 if (c != 0)
519 return;
520
521 debug("Read Cap: LBA %02X%02X%02X%02X blksize %02X%02X%02X%02X\n",
522 iobuf[0], iobuf[1], iobuf[2], iobuf[3],
523 iobuf[4], iobuf[5], iobuf[6], iobuf[7]);
524
525 dev_desc->lba = ((unsigned long) iobuf[0] << 24) +
526 ((unsigned long) iobuf[1] << 16) +
527 ((unsigned long) iobuf[2] << 8) + ((unsigned long) iobuf[3]);
528 dev_desc->blksz = ((unsigned long) iobuf[4] << 24) +
529 ((unsigned long) iobuf[5] << 16) +
530 ((unsigned long) iobuf[6] << 8) + ((unsigned long) iobuf[7]);
531 dev_desc->log2blksz = LOG2(dev_desc->blksz);
532#ifdef CONFIG_LBA48
533 /* ATAPI devices cannot use 48bit addressing (ATA/ATAPI v7) */
534 dev_desc->lba48 = 0;
535#endif
536 return;
537}
538
539#endif /* CONFIG_ATAPI */
540
541static void ide_ident(struct blk_desc *dev_desc)
542{
543 unsigned char c;
544 hd_driveid_t iop;
545
546#ifdef CONFIG_ATAPI
547 int retries = 0;
548#endif
549 int device;
550
551 device = dev_desc->devnum;
552 printf(" Device %d: ", device);
553
Simon Glasse9be1ee2016-05-01 11:36:10 -0600554 /* Select device
555 */
556 ide_outb(device, ATA_DEV_HD, ATA_LBA | ATA_DEVICE(device));
557 dev_desc->if_type = IF_TYPE_IDE;
558#ifdef CONFIG_ATAPI
559
560 retries = 0;
561
562 /* Warning: This will be tricky to read */
563 while (retries <= 1) {
564 /* check signature */
565 if ((ide_inb(device, ATA_SECT_CNT) == 0x01) &&
566 (ide_inb(device, ATA_SECT_NUM) == 0x01) &&
567 (ide_inb(device, ATA_CYL_LOW) == 0x14) &&
568 (ide_inb(device, ATA_CYL_HIGH) == 0xEB)) {
569 /* ATAPI Signature found */
570 dev_desc->if_type = IF_TYPE_ATAPI;
571 /*
572 * Start Ident Command
573 */
574 ide_outb(device, ATA_COMMAND, ATAPI_CMD_IDENT);
575 /*
576 * Wait for completion - ATAPI devices need more time
577 * to become ready
578 */
579 c = ide_wait(device, ATAPI_TIME_OUT);
580 } else
581#endif
582 {
583 /*
584 * Start Ident Command
585 */
586 ide_outb(device, ATA_COMMAND, ATA_CMD_IDENT);
587
588 /*
589 * Wait for completion
590 */
591 c = ide_wait(device, IDE_TIME_OUT);
592 }
Simon Glasse9be1ee2016-05-01 11:36:10 -0600593
594 if (((c & ATA_STAT_DRQ) == 0) ||
595 ((c & (ATA_STAT_FAULT | ATA_STAT_ERR)) != 0)) {
596#ifdef CONFIG_ATAPI
597 {
598 /*
599 * Need to soft reset the device
600 * in case it's an ATAPI...
601 */
602 debug("Retrying...\n");
603 ide_outb(device, ATA_DEV_HD,
604 ATA_LBA | ATA_DEVICE(device));
605 udelay(100000);
606 ide_outb(device, ATA_COMMAND, 0x08);
607 udelay(500000); /* 500 ms */
608 }
609 /*
610 * Select device
611 */
612 ide_outb(device, ATA_DEV_HD,
613 ATA_LBA | ATA_DEVICE(device));
614 retries++;
615#else
616 return;
617#endif
618 }
619#ifdef CONFIG_ATAPI
620 else
621 break;
622 } /* see above - ugly to read */
623
624 if (retries == 2) /* Not found */
625 return;
626#endif
627
628 ide_input_swap_data(device, (ulong *)&iop, ATA_SECTORWORDS);
629
630 ident_cpy((unsigned char *)dev_desc->revision, iop.fw_rev,
631 sizeof(dev_desc->revision));
632 ident_cpy((unsigned char *)dev_desc->vendor, iop.model,
633 sizeof(dev_desc->vendor));
634 ident_cpy((unsigned char *)dev_desc->product, iop.serial_no,
635 sizeof(dev_desc->product));
636#ifdef __LITTLE_ENDIAN
637 /*
638 * firmware revision, model, and serial number have Big Endian Byte
639 * order in Word. Convert all three to little endian.
640 *
641 * See CF+ and CompactFlash Specification Revision 2.0:
642 * 6.2.1.6: Identify Drive, Table 39 for more details
643 */
644
645 strswab(dev_desc->revision);
646 strswab(dev_desc->vendor);
647 strswab(dev_desc->product);
648#endif /* __LITTLE_ENDIAN */
649
650 if ((iop.config & 0x0080) == 0x0080)
651 dev_desc->removable = 1;
652 else
653 dev_desc->removable = 0;
654
655#ifdef CONFIG_ATAPI
656 if (dev_desc->if_type == IF_TYPE_ATAPI) {
657 atapi_inquiry(dev_desc);
658 return;
659 }
660#endif /* CONFIG_ATAPI */
661
662#ifdef __BIG_ENDIAN
663 /* swap shorts */
664 dev_desc->lba = (iop.lba_capacity << 16) | (iop.lba_capacity >> 16);
665#else /* ! __BIG_ENDIAN */
666 /*
667 * do not swap shorts on little endian
668 *
669 * See CF+ and CompactFlash Specification Revision 2.0:
670 * 6.2.1.6: Identfy Drive, Table 39, Word Address 57-58 for details.
671 */
672 dev_desc->lba = iop.lba_capacity;
673#endif /* __BIG_ENDIAN */
674
675#ifdef CONFIG_LBA48
676 if (iop.command_set_2 & 0x0400) { /* LBA 48 support */
677 dev_desc->lba48 = 1;
678 dev_desc->lba = (unsigned long long) iop.lba48_capacity[0] |
679 ((unsigned long long) iop.lba48_capacity[1] << 16) |
680 ((unsigned long long) iop.lba48_capacity[2] << 32) |
681 ((unsigned long long) iop.lba48_capacity[3] << 48);
682 } else {
683 dev_desc->lba48 = 0;
684 }
685#endif /* CONFIG_LBA48 */
686 /* assuming HD */
687 dev_desc->type = DEV_TYPE_HARDDISK;
688 dev_desc->blksz = ATA_BLOCKSIZE;
689 dev_desc->log2blksz = LOG2(dev_desc->blksz);
690 dev_desc->lun = 0; /* just to fill something in... */
691
692#if 0 /* only used to test the powersaving mode,
693 * if enabled, the drive goes after 5 sec
694 * in standby mode */
695 ide_outb(device, ATA_DEV_HD, ATA_LBA | ATA_DEVICE(device));
696 c = ide_wait(device, IDE_TIME_OUT);
697 ide_outb(device, ATA_SECT_CNT, 1);
698 ide_outb(device, ATA_LBA_LOW, 0);
699 ide_outb(device, ATA_LBA_MID, 0);
700 ide_outb(device, ATA_LBA_HIGH, 0);
701 ide_outb(device, ATA_DEV_HD, ATA_LBA | ATA_DEVICE(device));
702 ide_outb(device, ATA_COMMAND, 0xe3);
703 udelay(50);
704 c = ide_wait(device, IDE_TIME_OUT); /* can't take over 500 ms */
705#endif
706}
707
Simon Glasse9be1ee2016-05-01 11:36:10 -0600708__weak void ide_outb(int dev, int port, unsigned char val)
709{
710 debug("ide_outb (dev= %d, port= 0x%x, val= 0x%02x) : @ 0x%08lx\n",
711 dev, port, val,
712 (ATA_CURR_BASE(dev) + CONFIG_SYS_ATA_PORT_ADDR(port)));
713
714#if defined(CONFIG_IDE_AHB)
715 if (port) {
716 /* write command */
717 ide_write_register(dev, port, val);
718 } else {
719 /* write data */
720 outb(val, (ATA_CURR_BASE(dev)));
721 }
722#else
723 outb(val, (ATA_CURR_BASE(dev) + CONFIG_SYS_ATA_PORT_ADDR(port)));
724#endif
725}
726
727__weak unsigned char ide_inb(int dev, int port)
728{
729 uchar val;
730
731#if defined(CONFIG_IDE_AHB)
732 val = ide_read_register(dev, port);
733#else
734 val = inb((ATA_CURR_BASE(dev) + CONFIG_SYS_ATA_PORT_ADDR(port)));
735#endif
736
737 debug("ide_inb (dev= %d, port= 0x%x) : @ 0x%08lx -> 0x%02x\n",
738 dev, port,
739 (ATA_CURR_BASE(dev) + CONFIG_SYS_ATA_PORT_ADDR(port)), val);
740 return val;
741}
742
743void ide_init(void)
744{
745 unsigned char c;
746 int i, bus;
747
Simon Glasse9be1ee2016-05-01 11:36:10 -0600748#ifdef CONFIG_IDE_PREINIT
749 WATCHDOG_RESET();
750
751 if (ide_preinit()) {
752 puts("ide_preinit failed\n");
753 return;
754 }
755#endif /* CONFIG_IDE_PREINIT */
756
757 WATCHDOG_RESET();
758
Simon Glasse9be1ee2016-05-01 11:36:10 -0600759 /* ATAPI Drives seems to need a proper IDE Reset */
760 ide_reset();
761
Simon Glasse9be1ee2016-05-01 11:36:10 -0600762 /*
763 * Wait for IDE to get ready.
764 * According to spec, this can take up to 31 seconds!
765 */
766 for (bus = 0; bus < CONFIG_SYS_IDE_MAXBUS; ++bus) {
767 int dev =
768 bus * (CONFIG_SYS_IDE_MAXDEVICE /
769 CONFIG_SYS_IDE_MAXBUS);
770
Simon Glasse9be1ee2016-05-01 11:36:10 -0600771 printf("Bus %d: ", bus);
772
773 ide_bus_ok[bus] = 0;
774
775 /* Select device
776 */
777 udelay(100000); /* 100 ms */
778 ide_outb(dev, ATA_DEV_HD, ATA_LBA | ATA_DEVICE(dev));
779 udelay(100000); /* 100 ms */
780 i = 0;
781 do {
782 udelay(10000); /* 10 ms */
783
784 c = ide_inb(dev, ATA_STATUS);
785 i++;
786 if (i > (ATA_RESET_TIME * 100)) {
787 puts("** Timeout **\n");
Simon Glasse9be1ee2016-05-01 11:36:10 -0600788 return;
789 }
790 if ((i >= 100) && ((i % 100) == 0))
791 putc('.');
792
793 } while (c & ATA_STAT_BUSY);
794
795 if (c & (ATA_STAT_BUSY | ATA_STAT_FAULT)) {
796 puts("not available ");
797 debug("Status = 0x%02X ", c);
798#ifndef CONFIG_ATAPI /* ATAPI Devices do not set DRDY */
799 } else if ((c & ATA_STAT_READY) == 0) {
800 puts("not available ");
801 debug("Status = 0x%02X ", c);
802#endif
803 } else {
804 puts("OK ");
805 ide_bus_ok[bus] = 1;
806 }
807 WATCHDOG_RESET();
808 }
809
810 putc('\n');
811
Simon Glasse9be1ee2016-05-01 11:36:10 -0600812 for (i = 0; i < CONFIG_SYS_IDE_MAXDEVICE; ++i) {
Simon Glasse9be1ee2016-05-01 11:36:10 -0600813 ide_dev_desc[i].type = DEV_TYPE_UNKNOWN;
814 ide_dev_desc[i].if_type = IF_TYPE_IDE;
815 ide_dev_desc[i].devnum = i;
816 ide_dev_desc[i].part_type = PART_TYPE_UNKNOWN;
817 ide_dev_desc[i].blksz = 0;
818 ide_dev_desc[i].log2blksz =
819 LOG2_INVALID(typeof(ide_dev_desc[i].log2blksz));
820 ide_dev_desc[i].lba = 0;
Simon Glass145df842016-05-01 11:36:22 -0600821#ifndef CONFIG_BLK
Simon Glasse9be1ee2016-05-01 11:36:10 -0600822 ide_dev_desc[i].block_read = ide_read;
823 ide_dev_desc[i].block_write = ide_write;
Simon Glass145df842016-05-01 11:36:22 -0600824#endif
Simon Glasse9be1ee2016-05-01 11:36:10 -0600825 if (!ide_bus_ok[IDE_BUS(i)])
826 continue;
Simon Glasse9be1ee2016-05-01 11:36:10 -0600827 ide_ident(&ide_dev_desc[i]);
Simon Glasse9be1ee2016-05-01 11:36:10 -0600828 dev_print(&ide_dev_desc[i]);
829
Bin Meng68e6f222017-09-10 05:12:51 -0700830#ifndef CONFIG_BLK
Simon Glasse9be1ee2016-05-01 11:36:10 -0600831 if ((ide_dev_desc[i].lba > 0) && (ide_dev_desc[i].blksz > 0)) {
832 /* initialize partition type */
833 part_init(&ide_dev_desc[i]);
834 }
Bin Meng68e6f222017-09-10 05:12:51 -0700835#endif
Simon Glasse9be1ee2016-05-01 11:36:10 -0600836 }
837 WATCHDOG_RESET();
Bin Meng68e6f222017-09-10 05:12:51 -0700838
839#ifdef CONFIG_BLK
840 struct udevice *dev;
841
842 uclass_first_device(UCLASS_IDE, &dev);
843#endif
Simon Glasse9be1ee2016-05-01 11:36:10 -0600844}
845
Simon Glasse9be1ee2016-05-01 11:36:10 -0600846/* We only need to swap data if we are running on a big endian cpu. */
847#if defined(__LITTLE_ENDIAN)
848__weak void ide_input_swap_data(int dev, ulong *sect_buf, int words)
849{
850 ide_input_data(dev, sect_buf, words);
851}
852#else
853__weak void ide_input_swap_data(int dev, ulong *sect_buf, int words)
854{
855 volatile ushort *pbuf =
856 (ushort *)(ATA_CURR_BASE(dev) + ATA_DATA_REG);
857 ushort *dbuf = (ushort *)sect_buf;
858
859 debug("in input swap data base for read is %lx\n",
860 (unsigned long) pbuf);
861
862 while (words--) {
863#ifdef __MIPS__
864 *dbuf++ = swab16p((u16 *)pbuf);
865 *dbuf++ = swab16p((u16 *)pbuf);
866#else
867 *dbuf++ = ld_le16(pbuf);
868 *dbuf++ = ld_le16(pbuf);
869#endif /* !MIPS */
870 }
871}
872#endif /* __LITTLE_ENDIAN */
873
874
875#if defined(CONFIG_IDE_SWAP_IO)
876__weak void ide_output_data(int dev, const ulong *sect_buf, int words)
877{
878 ushort *dbuf;
879 volatile ushort *pbuf;
880
881 pbuf = (ushort *)(ATA_CURR_BASE(dev) + ATA_DATA_REG);
882 dbuf = (ushort *)sect_buf;
883 while (words--) {
884 EIEIO;
885 *pbuf = *dbuf++;
886 EIEIO;
887 *pbuf = *dbuf++;
888 }
889}
890#else /* ! CONFIG_IDE_SWAP_IO */
891__weak void ide_output_data(int dev, const ulong *sect_buf, int words)
892{
893#if defined(CONFIG_IDE_AHB)
894 ide_write_data(dev, sect_buf, words);
895#else
896 outsw(ATA_CURR_BASE(dev) + ATA_DATA_REG, sect_buf, words << 1);
897#endif
898}
899#endif /* CONFIG_IDE_SWAP_IO */
900
901#if defined(CONFIG_IDE_SWAP_IO)
902__weak void ide_input_data(int dev, ulong *sect_buf, int words)
903{
904 ushort *dbuf;
905 volatile ushort *pbuf;
906
907 pbuf = (ushort *)(ATA_CURR_BASE(dev) + ATA_DATA_REG);
908 dbuf = (ushort *)sect_buf;
909
910 debug("in input data base for read is %lx\n", (unsigned long) pbuf);
911
912 while (words--) {
913 EIEIO;
914 *dbuf++ = *pbuf;
915 EIEIO;
916 *dbuf++ = *pbuf;
917 }
918}
919#else /* ! CONFIG_IDE_SWAP_IO */
920__weak void ide_input_data(int dev, ulong *sect_buf, int words)
921{
922#if defined(CONFIG_IDE_AHB)
923 ide_read_data(dev, sect_buf, words);
924#else
925 insw(ATA_CURR_BASE(dev) + ATA_DATA_REG, sect_buf, words << 1);
926#endif
927}
928
929#endif /* CONFIG_IDE_SWAP_IO */
930
Simon Glass145df842016-05-01 11:36:22 -0600931#ifdef CONFIG_BLK
932ulong ide_read(struct udevice *dev, lbaint_t blknr, lbaint_t blkcnt,
933 void *buffer)
934#else
Simon Glasse9be1ee2016-05-01 11:36:10 -0600935ulong ide_read(struct blk_desc *block_dev, lbaint_t blknr, lbaint_t blkcnt,
936 void *buffer)
Simon Glass145df842016-05-01 11:36:22 -0600937#endif
Simon Glasse9be1ee2016-05-01 11:36:10 -0600938{
Simon Glass145df842016-05-01 11:36:22 -0600939#ifdef CONFIG_BLK
940 struct blk_desc *block_dev = dev_get_uclass_platdata(dev);
941#endif
Simon Glasse9be1ee2016-05-01 11:36:10 -0600942 int device = block_dev->devnum;
943 ulong n = 0;
944 unsigned char c;
945 unsigned char pwrsave = 0; /* power save */
946
947#ifdef CONFIG_LBA48
948 unsigned char lba48 = 0;
949
950 if (blknr & 0x0000fffff0000000ULL) {
951 /* more than 28 bits used, use 48bit mode */
952 lba48 = 1;
953 }
954#endif
955 debug("ide_read dev %d start " LBAF ", blocks " LBAF " buffer at %lX\n",
956 device, blknr, blkcnt, (ulong) buffer);
957
Simon Glasse9be1ee2016-05-01 11:36:10 -0600958 /* Select device
959 */
960 ide_outb(device, ATA_DEV_HD, ATA_LBA | ATA_DEVICE(device));
961 c = ide_wait(device, IDE_TIME_OUT);
962
963 if (c & ATA_STAT_BUSY) {
964 printf("IDE read: device %d not ready\n", device);
965 goto IDE_READ_E;
966 }
967
968 /* first check if the drive is in Powersaving mode, if yes,
969 * increase the timeout value */
970 ide_outb(device, ATA_COMMAND, ATA_CMD_CHK_PWR);
971 udelay(50);
972
973 c = ide_wait(device, IDE_TIME_OUT); /* can't take over 500 ms */
974
975 if (c & ATA_STAT_BUSY) {
976 printf("IDE read: device %d not ready\n", device);
977 goto IDE_READ_E;
978 }
979 if ((c & ATA_STAT_ERR) == ATA_STAT_ERR) {
980 printf("No Powersaving mode %X\n", c);
981 } else {
982 c = ide_inb(device, ATA_SECT_CNT);
983 debug("Powersaving %02X\n", c);
984 if (c == 0)
985 pwrsave = 1;
986 }
987
988
989 while (blkcnt-- > 0) {
990 c = ide_wait(device, IDE_TIME_OUT);
991
992 if (c & ATA_STAT_BUSY) {
993 printf("IDE read: device %d not ready\n", device);
994 break;
995 }
996#ifdef CONFIG_LBA48
997 if (lba48) {
998 /* write high bits */
999 ide_outb(device, ATA_SECT_CNT, 0);
1000 ide_outb(device, ATA_LBA_LOW, (blknr >> 24) & 0xFF);
1001#ifdef CONFIG_SYS_64BIT_LBA
1002 ide_outb(device, ATA_LBA_MID, (blknr >> 32) & 0xFF);
1003 ide_outb(device, ATA_LBA_HIGH, (blknr >> 40) & 0xFF);
1004#else
1005 ide_outb(device, ATA_LBA_MID, 0);
1006 ide_outb(device, ATA_LBA_HIGH, 0);
1007#endif
1008 }
1009#endif
1010 ide_outb(device, ATA_SECT_CNT, 1);
1011 ide_outb(device, ATA_LBA_LOW, (blknr >> 0) & 0xFF);
1012 ide_outb(device, ATA_LBA_MID, (blknr >> 8) & 0xFF);
1013 ide_outb(device, ATA_LBA_HIGH, (blknr >> 16) & 0xFF);
1014
1015#ifdef CONFIG_LBA48
1016 if (lba48) {
1017 ide_outb(device, ATA_DEV_HD,
1018 ATA_LBA | ATA_DEVICE(device));
1019 ide_outb(device, ATA_COMMAND, ATA_CMD_READ_EXT);
1020
1021 } else
1022#endif
1023 {
1024 ide_outb(device, ATA_DEV_HD, ATA_LBA |
1025 ATA_DEVICE(device) | ((blknr >> 24) & 0xF));
1026 ide_outb(device, ATA_COMMAND, ATA_CMD_READ);
1027 }
1028
1029 udelay(50);
1030
1031 if (pwrsave) {
1032 /* may take up to 4 sec */
1033 c = ide_wait(device, IDE_SPIN_UP_TIME_OUT);
1034 pwrsave = 0;
1035 } else {
1036 /* can't take over 500 ms */
1037 c = ide_wait(device, IDE_TIME_OUT);
1038 }
1039
1040 if ((c & (ATA_STAT_DRQ | ATA_STAT_BUSY | ATA_STAT_ERR)) !=
1041 ATA_STAT_DRQ) {
1042 printf("Error (no IRQ) dev %d blk " LBAF
1043 ": status %#02x\n", device, blknr, c);
1044 break;
1045 }
1046
1047 ide_input_data(device, buffer, ATA_SECTORWORDS);
1048 (void) ide_inb(device, ATA_STATUS); /* clear IRQ */
1049
1050 ++n;
1051 ++blknr;
1052 buffer += ATA_BLOCKSIZE;
1053 }
1054IDE_READ_E:
Simon Glasse9be1ee2016-05-01 11:36:10 -06001055 return n;
1056}
1057
Simon Glass145df842016-05-01 11:36:22 -06001058#ifdef CONFIG_BLK
1059ulong ide_write(struct udevice *dev, lbaint_t blknr, lbaint_t blkcnt,
1060 const void *buffer)
1061#else
Simon Glasse9be1ee2016-05-01 11:36:10 -06001062ulong ide_write(struct blk_desc *block_dev, lbaint_t blknr, lbaint_t blkcnt,
1063 const void *buffer)
Simon Glass145df842016-05-01 11:36:22 -06001064#endif
Simon Glasse9be1ee2016-05-01 11:36:10 -06001065{
Simon Glass145df842016-05-01 11:36:22 -06001066#ifdef CONFIG_BLK
1067 struct blk_desc *block_dev = dev_get_uclass_platdata(dev);
1068#endif
Simon Glasse9be1ee2016-05-01 11:36:10 -06001069 int device = block_dev->devnum;
1070 ulong n = 0;
1071 unsigned char c;
1072
1073#ifdef CONFIG_LBA48
1074 unsigned char lba48 = 0;
1075
1076 if (blknr & 0x0000fffff0000000ULL) {
1077 /* more than 28 bits used, use 48bit mode */
1078 lba48 = 1;
1079 }
1080#endif
1081
Simon Glasse9be1ee2016-05-01 11:36:10 -06001082 /* Select device
1083 */
1084 ide_outb(device, ATA_DEV_HD, ATA_LBA | ATA_DEVICE(device));
1085
1086 while (blkcnt-- > 0) {
1087 c = ide_wait(device, IDE_TIME_OUT);
1088
1089 if (c & ATA_STAT_BUSY) {
1090 printf("IDE read: device %d not ready\n", device);
1091 goto WR_OUT;
1092 }
1093#ifdef CONFIG_LBA48
1094 if (lba48) {
1095 /* write high bits */
1096 ide_outb(device, ATA_SECT_CNT, 0);
1097 ide_outb(device, ATA_LBA_LOW, (blknr >> 24) & 0xFF);
1098#ifdef CONFIG_SYS_64BIT_LBA
1099 ide_outb(device, ATA_LBA_MID, (blknr >> 32) & 0xFF);
1100 ide_outb(device, ATA_LBA_HIGH, (blknr >> 40) & 0xFF);
1101#else
1102 ide_outb(device, ATA_LBA_MID, 0);
1103 ide_outb(device, ATA_LBA_HIGH, 0);
1104#endif
1105 }
1106#endif
1107 ide_outb(device, ATA_SECT_CNT, 1);
1108 ide_outb(device, ATA_LBA_LOW, (blknr >> 0) & 0xFF);
1109 ide_outb(device, ATA_LBA_MID, (blknr >> 8) & 0xFF);
1110 ide_outb(device, ATA_LBA_HIGH, (blknr >> 16) & 0xFF);
1111
1112#ifdef CONFIG_LBA48
1113 if (lba48) {
1114 ide_outb(device, ATA_DEV_HD,
1115 ATA_LBA | ATA_DEVICE(device));
1116 ide_outb(device, ATA_COMMAND, ATA_CMD_WRITE_EXT);
1117
1118 } else
1119#endif
1120 {
1121 ide_outb(device, ATA_DEV_HD, ATA_LBA |
1122 ATA_DEVICE(device) | ((blknr >> 24) & 0xF));
1123 ide_outb(device, ATA_COMMAND, ATA_CMD_WRITE);
1124 }
1125
1126 udelay(50);
1127
1128 /* can't take over 500 ms */
1129 c = ide_wait(device, IDE_TIME_OUT);
1130
1131 if ((c & (ATA_STAT_DRQ | ATA_STAT_BUSY | ATA_STAT_ERR)) !=
1132 ATA_STAT_DRQ) {
1133 printf("Error (no IRQ) dev %d blk " LBAF
1134 ": status %#02x\n", device, blknr, c);
1135 goto WR_OUT;
1136 }
1137
1138 ide_output_data(device, buffer, ATA_SECTORWORDS);
1139 c = ide_inb(device, ATA_STATUS); /* clear IRQ */
1140 ++n;
1141 ++blknr;
1142 buffer += ATA_BLOCKSIZE;
1143 }
1144WR_OUT:
Simon Glasse9be1ee2016-05-01 11:36:10 -06001145 return n;
1146}
1147
1148#if defined(CONFIG_OF_IDE_FIXUP)
1149int ide_device_present(int dev)
1150{
1151 if (dev >= CONFIG_SYS_IDE_MAXBUS)
1152 return 0;
1153 return ide_dev_desc[dev].type == DEV_TYPE_UNKNOWN ? 0 : 1;
1154}
1155#endif
1156
Simon Glass145df842016-05-01 11:36:22 -06001157#ifdef CONFIG_BLK
Bin Meng68e6f222017-09-10 05:12:51 -07001158static int ide_blk_probe(struct udevice *udev)
1159{
1160 struct blk_desc *desc = dev_get_uclass_platdata(udev);
1161
1162 /* fill in device vendor/product/rev strings */
1163 strncpy(desc->vendor, ide_dev_desc[desc->devnum].vendor,
1164 BLK_VEN_SIZE);
1165 desc->vendor[BLK_VEN_SIZE] = '\0';
1166 strncpy(desc->product, ide_dev_desc[desc->devnum].product,
1167 BLK_PRD_SIZE);
1168 desc->product[BLK_PRD_SIZE] = '\0';
1169 strncpy(desc->revision, ide_dev_desc[desc->devnum].revision,
1170 BLK_REV_SIZE);
1171 desc->revision[BLK_REV_SIZE] = '\0';
1172
1173 part_init(desc);
1174
1175 return 0;
1176}
1177
Simon Glass145df842016-05-01 11:36:22 -06001178static const struct blk_ops ide_blk_ops = {
1179 .read = ide_read,
1180 .write = ide_write,
1181};
1182
1183U_BOOT_DRIVER(ide_blk) = {
1184 .name = "ide_blk",
1185 .id = UCLASS_BLK,
1186 .ops = &ide_blk_ops,
Bin Meng68e6f222017-09-10 05:12:51 -07001187 .probe = ide_blk_probe,
1188};
1189
1190static int ide_probe(struct udevice *udev)
1191{
1192 struct udevice *blk_dev;
1193 char name[20];
1194 int blksz;
1195 lbaint_t size;
1196 int i;
1197 int ret;
1198
1199 for (i = 0; i < CONFIG_SYS_IDE_MAXDEVICE; i++) {
1200 if (ide_dev_desc[i].type != DEV_TYPE_UNKNOWN) {
1201 sprintf(name, "blk#%d", i);
1202
1203 blksz = ide_dev_desc[i].blksz;
1204 size = blksz * ide_dev_desc[i].lba;
1205 ret = blk_create_devicef(udev, "ide_blk", name,
1206 IF_TYPE_IDE, i,
1207 blksz, size, &blk_dev);
1208 if (ret)
1209 return ret;
1210 }
1211 }
1212
1213 return 0;
1214}
1215
1216U_BOOT_DRIVER(ide) = {
1217 .name = "ide",
1218 .id = UCLASS_IDE,
1219 .probe = ide_probe,
1220};
1221
1222struct pci_device_id ide_supported[] = {
1223 { PCI_DEVICE_CLASS(PCI_CLASS_STORAGE_IDE << 8, 0xffff00) },
1224 { }
1225};
1226
1227U_BOOT_PCI_DEVICE(ide, ide_supported);
1228
1229UCLASS_DRIVER(ide) = {
1230 .name = "ide",
1231 .id = UCLASS_IDE,
Simon Glass145df842016-05-01 11:36:22 -06001232};
1233#else
Simon Glasse9be1ee2016-05-01 11:36:10 -06001234U_BOOT_LEGACY_BLK(ide) = {
1235 .if_typename = "ide",
1236 .if_type = IF_TYPE_IDE,
1237 .max_devs = CONFIG_SYS_IDE_MAXDEVICE,
1238 .desc = ide_dev_desc,
1239};
Simon Glass145df842016-05-01 11:36:22 -06001240#endif