ARM: imx6: dh-imx6: Enable d-cache early in SPL
Enable d-cache early in SPL right after DRAM is started up.
This reduces U-Boot proper load time by 650ms when loaded
from SPI NOR.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Philip Oberfichtner <pro@denx.de>
diff --git a/board/dhelectronics/dh_imx6/dh_imx6_spl.c b/board/dhelectronics/dh_imx6/dh_imx6_spl.c
index e49e977..20a330c 100644
--- a/board/dhelectronics/dh_imx6/dh_imx6_spl.c
+++ b/board/dhelectronics/dh_imx6/dh_imx6_spl.c
@@ -6,6 +6,7 @@
*/
#include <common.h>
+#include <cpu_func.h>
#include <init.h>
#include <asm/arch/clock.h>
#include <asm/arch/crm_regs.h>
@@ -14,11 +15,13 @@
#include <asm/arch/mx6-ddr.h>
#include <asm/arch/mx6-pins.h>
#include <asm/arch/sys_proto.h>
+#include <asm/cache.h>
#include <asm/gpio.h>
#include <asm/mach-imx/boot_mode.h>
#include <asm/mach-imx/iomux-v3.h>
#include <asm/mach-imx/mxc_i2c.h>
#include <asm/io.h>
+#include <asm/system.h>
#include <errno.h>
#include <fuse.h>
#include <fsl_esdhc_imx.h>
@@ -610,6 +613,20 @@
}
}
+void dram_bank_mmu_setup(int bank)
+{
+ int i;
+
+ set_section_dcache(ROMCP_ARB_BASE_ADDR >> MMU_SECTION_SHIFT, DCACHE_DEFAULT_OPTION);
+ set_section_dcache(IRAM_BASE_ADDR >> MMU_SECTION_SHIFT, DCACHE_DEFAULT_OPTION);
+
+ for (i = MMDC0_ARB_BASE_ADDR >> MMU_SECTION_SHIFT;
+ i < ((MMDC0_ARB_BASE_ADDR >> MMU_SECTION_SHIFT) +
+ (SZ_1G >> MMU_SECTION_SHIFT));
+ i++)
+ set_section_dcache(i, DCACHE_DEFAULT_OPTION);
+}
+
void board_init_f(ulong dummy)
{
/* setup AIPS and disable watchdog */
@@ -636,9 +653,33 @@
/* DDR3 initialization */
dhcom_spl_dram_init();
+ /* Set up early MMU tables at the beginning of DRAM and start d-cache */
+ gd->arch.tlb_addr = MMDC0_ARB_BASE_ADDR + SZ_32M;
+ gd->arch.tlb_size = PGTABLE_SIZE;
+ enable_caches();
+
/* Clear the BSS. */
memset(__bss_start, 0, __bss_end - __bss_start);
/* load/boot image from boot device */
board_init_r(NULL, 0);
}
+
+void spl_board_prepare_for_boot(void)
+{
+ /*
+ * Flush and disable dcache. Without it, the following bootstage might fail randomly because
+ * dirty cache lines may not have been written back to DRAM.
+ *
+ * If dcache_disable() would be omitted, the following scenario may occur:
+ *
+ * The SPL enables dcache and cachelines get populated with data. Then dcache gets disabled
+ * in U-Boot proper, but still contains dirty data, i.e. the corresponding DRAM locations
+ * have not yet been updated. When U-Boot reads these locations, it sees an (incorrect) old
+ * state of the content.
+ *
+ * Furthermore, the DRAM contents have likely been modified by U-Boot while dcache was
+ * disabled. Thus, U-Boot flushing dcache would corrupt DRAM with stale data.
+ */
+ dcache_disable(); /* implies flush_dcache_all() */
+}
diff --git a/configs/dh_imx6_defconfig b/configs/dh_imx6_defconfig
index 4b6776e..c7fb2c6 100644
--- a/configs/dh_imx6_defconfig
+++ b/configs/dh_imx6_defconfig
@@ -1,4 +1,5 @@
CONFIG_ARM=y
+CONFIG_SPL_SYS_L2_PL310=y
CONFIG_ARCH_MX6=y
CONFIG_SYS_TEXT_BASE=0x17800000
CONFIG_SYS_MALLOC_F_LEN=0x1000