armv8/ls1043ardb: Add LS1043ARDB board support

LS1043ARDB Specification:
-------------------------
Memory subsystem:
 * 2GByte DDR4 SDRAM (32bit bus)
 * 128 Mbyte NOR flash single-chip memory
 * 512 Mbyte NAND flash
 * 16 Mbyte high-speed SPI flash
 * SD connector to interface with the SD memory card

Ethernet:
 * XFI 10G port
 * QSGMII with 4x 1G ports
 * Two RGMII ports

PCIe:
 * PCIe2 (Lanes C) to mini-PCIe slot
 * PCIe3 (Lanes D) to PCIe slot

USB 3.0: two super speed USB 3.0 type A ports

UART: supports two UARTs up to 115200 bps for console

Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
diff --git a/board/freescale/ls1043ardb/ls1043ardb.c b/board/freescale/ls1043ardb/ls1043ardb.c
new file mode 100644
index 0000000..5b7f814
--- /dev/null
+++ b/board/freescale/ls1043ardb/ls1043ardb.c
@@ -0,0 +1,131 @@
+/*
+ * Copyright 2015 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <i2c.h>
+#include <asm/io.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/fsl_serdes.h>
+#include <asm/arch/soc.h>
+#include <hwconfig.h>
+#include <ahci.h>
+#include <scsi.h>
+#include <fsl_csu.h>
+#include <fsl_esdhc.h>
+#include <fsl_ifc.h>
+#include "cpld.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int checkboard(void)
+{
+	static const char *freq[3] = {"100.00MHZ", "156.25MHZ"};
+	u8 cfg_rcw_src1, cfg_rcw_src2;
+	u32 cfg_rcw_src;
+	u32 sd1refclk_sel;
+
+	printf("Board: LS1043ARDB, boot from ");
+
+	cfg_rcw_src1 = CPLD_READ(cfg_rcw_src1);
+	cfg_rcw_src2 = CPLD_READ(cfg_rcw_src2);
+	cpld_rev_bit(&cfg_rcw_src1);
+	cfg_rcw_src = cfg_rcw_src1;
+	cfg_rcw_src = (cfg_rcw_src << 1) | cfg_rcw_src2;
+
+	if (cfg_rcw_src == 0x25)
+		printf("vBank %d\n", CPLD_READ(vbank));
+	else if (cfg_rcw_src == 0x106)
+		puts("NAND\n");
+	else
+		printf("Invalid setting of SW4\n");
+
+	printf("CPLD:  V%x.%x\nPCBA:  V%x.0\n", CPLD_READ(cpld_ver),
+	       CPLD_READ(cpld_ver_sub), CPLD_READ(pcba_ver));
+
+	puts("SERDES Reference Clocks:\n");
+	sd1refclk_sel = CPLD_READ(sd1refclk_sel);
+	printf("SD1_CLK1 = %s, SD1_CLK2 = %s\n", freq[sd1refclk_sel], freq[0]);
+
+	return 0;
+}
+
+int dram_init(void)
+{
+	gd->ram_size = initdram(0);
+
+	return 0;
+}
+
+int board_early_init_f(void)
+{
+	fsl_lsch2_early_init_f();
+	return 0;
+}
+
+int board_init(void)
+{
+	struct ccsr_cci400 *cci = (struct ccsr_cci400 *)CONFIG_SYS_CCI400_ADDR;
+
+	/*
+	 * Set CCI-400 control override register to enable barrier
+	 * transaction
+	 */
+	out_le32(&cci->ctrl_ord, CCI400_CTRLORD_EN_BARRIER);
+
+#ifdef CONFIG_FSL_IFC
+	init_final_memctl_regs();
+#endif
+
+#ifdef CONFIG_ENV_IS_NOWHERE
+	gd->env_addr = (ulong)&default_environment[0];
+#endif
+
+#ifdef CONFIG_LAYERSCAPE_NS_ACCESS
+	enable_layerscape_ns_access();
+#endif
+
+	return 0;
+}
+
+int config_board_mux(void)
+{
+	return 0;
+}
+
+#if defined(CONFIG_MISC_INIT_R)
+int misc_init_r(void)
+{
+	config_board_mux();
+
+	return 0;
+}
+#endif
+
+int ft_board_setup(void *blob, bd_t *bd)
+{
+	ft_cpu_setup(blob, bd);
+
+	return 0;
+}
+
+u8 flash_read8(void *addr)
+{
+	return __raw_readb(addr + 1);
+}
+
+void flash_write16(u16 val, void *addr)
+{
+	u16 shftval = (((val >> 8) & 0xff) | ((val << 8) & 0xff00));
+
+	__raw_writew(shftval, addr);
+}
+
+u16 flash_read16(void *addr)
+{
+	u16 val = __raw_readw(addr);
+
+	return (((val) >> 8) & 0x00ff) | (((val) << 8) & 0xff00);
+}