ppc4xx: Update AMCC Makalu for board rev 1.1
This patch adds changes needed for Makalu rev 1.1:
- Enable 2nd DDR2 bank resulting in 256MByte of SDRAM
- Enable 2nd ethernet port EMAC1
- Use generic GPIO configuration framework (CFG_4xx_GPIO_TABLE)
- Reset PCIe ports via GPIO upon bootup
Signed-off-by: Stefan Roese <sr@denx.de>
diff --git a/board/amcc/makalu/makalu.c b/board/amcc/makalu/makalu.c
index 3b4a9c1..b7933a0 100644
--- a/board/amcc/makalu/makalu.c
+++ b/board/amcc/makalu/makalu.c
@@ -26,7 +26,8 @@
#include <ppc405.h>
#include <libfdt.h>
#include <asm/processor.h>
-#include <asm-ppc/io.h>
+#include <asm/gpio.h>
+#include <asm/io.h>
#if defined(CONFIG_PCI)
#include <pci.h>
@@ -189,6 +190,11 @@
*/
mtsdr(SDR0_SRST, 0);
+ /* Reset PCIe slots */
+ gpio_write_bit(CFG_GPIO_PCIE_RST, 0);
+ udelay(100);
+ gpio_write_bit(CFG_GPIO_PCIE_RST, 1);
+
return 0;
}
@@ -239,45 +245,6 @@
}
#endif /* defined(CONFIG_PCI) */
-/*************************************************************************
- * pci_target_init
- *
- * The bootstrap configuration provides default settings for the pci
- * inbound map (PIM). But the bootstrap config choices are limited and
- * may not be sufficient for a given board.
- *
- ************************************************************************/
-#if defined(CONFIG_PCI) && defined(CFG_PCI_TARGET_INIT)
-void pci_target_init(struct pci_controller * hose )
-{
- /*-------------------------------------------------------------------+
- * Disable everything
- *-------------------------------------------------------------------*/
- out32r( PCIX0_PIM0SA, 0 ); /* disable */
- out32r( PCIX0_PIM1SA, 0 ); /* disable */
- out32r( PCIX0_PIM2SA, 0 ); /* disable */
- out32r( PCIX0_EROMBA, 0 ); /* disable expansion rom */
-
- /*-------------------------------------------------------------------+
- * Map all of SDRAM to PCI address 0x0000_0000. Note that the 440
- * strapping options to not support sizes such as 128/256 MB.
- *-------------------------------------------------------------------*/
- out32r( PCIX0_PIM0LAL, CFG_SDRAM_BASE );
- out32r( PCIX0_PIM0LAH, 0 );
- out32r( PCIX0_PIM0SA, ~(gd->ram_size - 1) | 1 );
-
- out32r( PCIX0_BAR0, 0 );
-
- /*-------------------------------------------------------------------+
- * Program the board's subsystem id/vendor id
- *-------------------------------------------------------------------*/
- out16r( PCIX0_SBSYSVID, CFG_PCI_SUBSYS_VENDORID );
- out16r( PCIX0_SBSYSID, CFG_PCI_SUBSYS_DEVICEID );
-
- out16r( PCIX0_CMD, in16r(PCIX0_CMD) | PCI_COMMAND_MEMORY );
-}
-#endif /* defined(CONFIG_PCI) && defined(CFG_PCI_TARGET_INIT) */
-
#ifdef CONFIG_PCI
static struct pci_controller pcie_hose[2] = {{0},{0}};
@@ -292,15 +259,13 @@
for (i = 0; i < 2; i++) {
- if (is_end_point(i)) {
- printf("PCIE%d: will be configured as endpoint\n", i);
+ if (is_end_point(i))
ret = ppc4xx_init_pcie_endport(i);
- } else {
- printf("PCIE%d: will be configured as root-complex\n", i);
+ else
ret = ppc4xx_init_pcie_rootport(i);
- }
if (ret) {
- printf("PCIE%d: initialization failed\n", i);
+ printf("PCIE%d: initialization as %s failed\n", i,
+ is_end_point(i) ? "endpoint" : "root-complex");
continue;
}