/*
 * (C) Copyright 2011 CompuLab, Ltd.
 * Mike Rapoport <mike@compulab.co.il>
 * Igor Grinberg <grinberg@compulab.co.il>
 *
 * Based on omap3_beagle.h
 * (C) Copyright 2006-2008
 * Texas Instruments.
 * Richard Woodruff <r-woodruff2@ti.com>
 * Syed Mohammed Khasim <x0khasim@ti.com>
 *
 * Configuration settings for the CompuLab CM-T35 and CM-T3730 boards
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

#ifndef __CONFIG_H
#define __CONFIG_H

#define CONFIG_SYS_CACHELINE_SIZE	64

/*
 * High Level Configuration Options
 */
#define CONFIG_OMAP	/* in a TI OMAP core */
#define CONFIG_OMAP_GPIO
#define CONFIG_CM_T3X	/* working with CM-T35 and CM-T3730 */
#define CONFIG_OMAP_COMMON
/* Common ARM Erratas */
#define CONFIG_ARM_ERRATA_454179
#define CONFIG_ARM_ERRATA_430973
#define CONFIG_ARM_ERRATA_621766

#define CONFIG_SDRC	/* The chip has SDRC controller */

#include <asm/arch/cpu.h>		/* get chip and board defs */
#include <asm/arch/omap.h>

/*
 * Display CPU and Board information
 */
#define CONFIG_DISPLAY_CPUINFO
#define CONFIG_DISPLAY_BOARDINFO

/* Clock Defines */
#define V_OSCK			26000000	/* Clock output from T2 */
#define V_SCLK			(V_OSCK >> 1)

#define CONFIG_MISC_INIT_R

#define CONFIG_CMDLINE_TAG		/* enable passing of ATAGs */
#define CONFIG_SETUP_MEMORY_TAGS
#define CONFIG_INITRD_TAG
#define CONFIG_REVISION_TAG
#define CONFIG_SERIAL_TAG

/*
 * Size of malloc() pool
 */
#define CONFIG_ENV_SIZE		(16 << 10)	/* 16 KiB */
					/* Sector */
#define CONFIG_SYS_MALLOC_LEN	(CONFIG_ENV_SIZE + (128 << 10))

/*
 * Hardware drivers
 */

/*
 * NS16550 Configuration
 */
#define V_NS16550_CLK			48000000	/* 48MHz (APLL96/2) */

#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE	(-4)
#define CONFIG_SYS_NS16550_CLK		V_NS16550_CLK

/*
 * select serial console configuration
 */
#define CONFIG_CONS_INDEX		3
#define CONFIG_SYS_NS16550_COM3		OMAP34XX_UART3
#define CONFIG_SERIAL3			3	/* UART3 */

/* allow to overwrite serial and ethaddr */
#define CONFIG_ENV_OVERWRITE
#define CONFIG_BAUDRATE			115200
#define CONFIG_SYS_BAUDRATE_TABLE	{4800, 9600, 19200, 38400, 57600,\
					115200}

#define CONFIG_GENERIC_MMC
#define CONFIG_MMC
#define CONFIG_OMAP_HSMMC
#define CONFIG_DOS_PARTITION

/* USB */
#define CONFIG_USB_OMAP3
#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_OMAP
#define CONFIG_USB_STORAGE
#define CONFIG_USB_MUSB_UDC
#define CONFIG_TWL4030_USB

/* USB device configuration */
#define CONFIG_USB_DEVICE
#define CONFIG_USB_TTY
#define CONFIG_SYS_CONSOLE_IS_IN_ENV

/* commands to include */
#define CONFIG_CMD_MTDPARTS	/* Enable MTD parts commands */
#define CONFIG_MTD_DEVICE	/* needed for mtdparts commands */
#define CONFIG_MTD_PARTITIONS
#define MTDIDS_DEFAULT		"nand0=nand"
#define MTDPARTS_DEFAULT	"mtdparts=nand:512k(x-loader),"\
				"1920k(u-boot),256k(u-boot-env),"\
				"4m(kernel),-(fs)"

#define CONFIG_CMD_NAND		/* NAND support			*/

#define CONFIG_SYS_NO_FLASH
#define CONFIG_SYS_I2C
#define CONFIG_SYS_OMAP24_I2C_SPEED	100000
#define CONFIG_SYS_OMAP24_I2C_SLAVE	1
#define CONFIG_SYS_I2C_OMAP34XX
#define CONFIG_SYS_I2C_EEPROM_ADDR	0x50
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	1
#define CONFIG_SYS_I2C_EEPROM_BUS	0
#define CONFIG_I2C_MULTI_BUS

/*
 * TWL4030
 */
#define CONFIG_TWL4030_POWER
#define CONFIG_TWL4030_LED

/*
 * Board NAND Info.
 */
#define CONFIG_NAND_OMAP_GPMC
#define CONFIG_SYS_NAND_ADDR		NAND_BASE	/* physical address */
							/* to access nand */
#define CONFIG_SYS_NAND_BASE		NAND_BASE	/* physical address */
							/* to access nand at */
							/* CS0 */
#define CONFIG_SYS_MAX_NAND_DEVICE	1		/* Max number of NAND */
							/* devices */

/* Environment information */
#define CONFIG_BOOTDELAY		3
#define CONFIG_ZERO_BOOTDELAY_CHECK

#define CONFIG_EXTRA_ENV_SETTINGS \
	"loadaddr=0x82000000\0" \
	"usbtty=cdc_acm\0" \
	"console=ttyO2,115200n8\0" \
	"mpurate=500\0" \
	"vram=12M\0" \
	"dvimode=1024x768MR-16@60\0" \
	"defaultdisplay=dvi\0" \
	"mmcdev=0\0" \
	"mmcroot=/dev/mmcblk0p2 rw\0" \
	"mmcrootfstype=ext4 rootwait\0" \
	"nandroot=/dev/mtdblock4 rw\0" \
	"nandrootfstype=ubifs\0" \
	"mmcargs=setenv bootargs console=${console} " \
		"mpurate=${mpurate} " \
		"vram=${vram} " \
		"omapfb.mode=dvi:${dvimode} " \
		"omapdss.def_disp=${defaultdisplay} " \
		"root=${mmcroot} " \
		"rootfstype=${mmcrootfstype}\0" \
	"nandargs=setenv bootargs console=${console} " \
		"mpurate=${mpurate} " \
		"vram=${vram} " \
		"omapfb.mode=dvi:${dvimode} " \
		"omapdss.def_disp=${defaultdisplay} " \
		"root=${nandroot} " \
		"rootfstype=${nandrootfstype}\0" \
	"loadbootscript=fatload mmc ${mmcdev} ${loadaddr} boot.scr\0" \
	"bootscript=echo Running bootscript from mmc ...; " \
		"source ${loadaddr}\0" \
	"loaduimage=fatload mmc ${mmcdev} ${loadaddr} uImage\0" \
	"mmcboot=echo Booting from mmc ...; " \
		"run mmcargs; " \
		"bootm ${loadaddr}\0" \
	"nandboot=echo Booting from nand ...; " \
		"run nandargs; " \
		"nand read ${loadaddr} 2a0000 400000; " \
		"bootm ${loadaddr}\0" \

#define CONFIG_BOOTCOMMAND \
	"mmc dev ${mmcdev}; if mmc rescan; then " \
		"if run loadbootscript; then " \
			"run bootscript; " \
		"else " \
			"if run loaduimage; then " \
				"run mmcboot; " \
			"else run nandboot; " \
			"fi; " \
		"fi; " \
	"else run nandboot; fi"

/*
 * Miscellaneous configurable options
 */
#define CONFIG_AUTO_COMPLETE
#define CONFIG_CMDLINE_EDITING
#define CONFIG_TIMESTAMP
#define CONFIG_SYS_AUTOLOAD		"no"
#define CONFIG_SYS_LONGHELP		/* undef to save memory */
#define CONFIG_SYS_CBSIZE		256	/* Console I/O Buffer Size */
/* Print Buffer Size */
#define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE + \
					sizeof(CONFIG_SYS_PROMPT) + 16)
#define CONFIG_SYS_MAXARGS		16	/* max number of command args */
/* Boot Argument Buffer Size */
#define CONFIG_SYS_BARGSIZE		(CONFIG_SYS_CBSIZE)

#define CONFIG_SYS_MEMTEST_START	(OMAP34XX_SDRC_CS0)	/* memtest */
								/* works on */
#define CONFIG_SYS_MEMTEST_END		(OMAP34XX_SDRC_CS0 + \
					0x01F00000) /* 31MB */

#define CONFIG_SYS_LOAD_ADDR		(OMAP34XX_SDRC_CS0)	/* default */
							/* load address */

/*
 * OMAP3 has 12 GP timers, they can be driven by the system clock
 * (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK).
 * This rate is divided by a local divisor.
 */
#define CONFIG_SYS_TIMERBASE		(OMAP34XX_GPT2)
#define CONFIG_SYS_PTV			2       /* Divisor: 2^(PTV+1) => 8 */

/*-----------------------------------------------------------------------
 * Physical Memory Map
 */
#define CONFIG_NR_DRAM_BANKS	1	/* CS1 is never populated */
#define PHYS_SDRAM_1		OMAP34XX_SDRC_CS0

/*-----------------------------------------------------------------------
 * FLASH and environment organization
 */

/* **** PISMO SUPPORT *** */
/* Monitor at start of flash */
#define CONFIG_SYS_MONITOR_BASE		CONFIG_SYS_FLASH_BASE
#define CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 2 sectors */

#define CONFIG_ENV_IS_IN_NAND
#define SMNAND_ENV_OFFSET		0x260000 /* environment starts here */
#define CONFIG_ENV_OFFSET		SMNAND_ENV_OFFSET
#define CONFIG_ENV_ADDR			SMNAND_ENV_OFFSET

#if defined(CONFIG_CMD_NET)
#define CONFIG_SMC911X
#define CONFIG_SMC911X_32_BIT
#define CM_T3X_SMC911X_BASE	0x2C000000
#define SB_T35_SMC911X_BASE	(CM_T3X_SMC911X_BASE + (16 << 20))
#define CONFIG_SMC911X_BASE	CM_T3X_SMC911X_BASE
#endif /* (CONFIG_CMD_NET) */

/* additions for new relocation code, must be added to all boards */
#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM_1
#define CONFIG_SYS_INIT_RAM_ADDR	0x4020f800
#define CONFIG_SYS_INIT_RAM_SIZE	0x800
#define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_INIT_RAM_ADDR +	\
					 CONFIG_SYS_INIT_RAM_SIZE -	\
					 GENERATED_GBL_DATA_SIZE)

/* Status LED */
#define CONFIG_STATUS_LED		/* Status LED enabled */
#define CONFIG_BOARD_SPECIFIC_LED
#define CONFIG_GPIO_LED
#define GREEN_LED_GPIO			186 /* CM-T35 Green LED is GPIO186 */
#define GREEN_LED_DEV			0
#define STATUS_LED_BIT			GREEN_LED_GPIO
#define STATUS_LED_STATE		STATUS_LED_ON
#define STATUS_LED_PERIOD		(CONFIG_SYS_HZ / 2)
#define STATUS_LED_BOOT			GREEN_LED_DEV

#define CONFIG_SPLASHIMAGE_GUARD

/* GPIO banks */
#ifdef CONFIG_STATUS_LED
#define CONFIG_OMAP3_GPIO_6	/* GPIO186 is in GPIO bank 6  */
#endif

/* Display Configuration */
#define CONFIG_OMAP3_GPIO_2
#define CONFIG_OMAP3_GPIO_5
#define CONFIG_VIDEO_OMAP3
#define LCD_BPP		LCD_COLOR16

#define CONFIG_LCD
#define CONFIG_SPLASH_SCREEN
#define CONFIG_SPLASH_SOURCE
#define CONFIG_CMD_BMP
#define CONFIG_BMP_16BPP
#define CONFIG_SCF0403_LCD

#define CONFIG_OMAP3_SPI

/* Defines for SPL */
#define CONFIG_SPL_FRAMEWORK
#define CONFIG_SPL_NAND_SIMPLE

#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR	0x300 /* address 0x60000 */
#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS	0x200 /* 256 KB */
#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION	1
#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME	"u-boot.img"

#define CONFIG_SPL_BOARD_INIT
#define CONFIG_SPL_LIBCOMMON_SUPPORT
#define CONFIG_SPL_LIBDISK_SUPPORT
#define CONFIG_SPL_I2C_SUPPORT
#define CONFIG_SPL_LIBGENERIC_SUPPORT
#define CONFIG_SPL_MMC_SUPPORT
#define CONFIG_SPL_FAT_SUPPORT
#define CONFIG_SPL_SERIAL_SUPPORT
#define CONFIG_SPL_NAND_SUPPORT
#define CONFIG_SPL_NAND_BASE
#define CONFIG_SPL_NAND_DRIVERS
#define CONFIG_SPL_NAND_ECC
#define CONFIG_SPL_GPIO_SUPPORT
#define CONFIG_SPL_POWER_SUPPORT
#define CONFIG_SPL_OMAP3_ID_NAND
#define CONFIG_SPL_LDSCRIPT		"$(CPUDIR)/omap-common/u-boot-spl.lds"

/* NAND boot config */
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
#define CONFIG_SYS_NAND_PAGE_COUNT	64
#define CONFIG_SYS_NAND_PAGE_SIZE	2048
#define CONFIG_SYS_NAND_OOBSIZE		64
#define CONFIG_SYS_NAND_BLOCK_SIZE	(128 * 1024)
#define CONFIG_SYS_NAND_BAD_BLOCK_POS	NAND_LARGE_BADBLOCK_POS
/*
 * Use the ECC/OOB layout from omap_gpmc.h that matches your chip:
 * SP vs LP, 8bit vs 16bit: GPMC_NAND_HW_ECC_LAYOUT
 */
#define CONFIG_SYS_NAND_ECCPOS		{ 1, 2, 3, 4, 5, 6, 7, 8, 9, \
					 10, 11, 12 }
#define CONFIG_SYS_NAND_ECCSIZE		512
#define CONFIG_SYS_NAND_ECCBYTES	3
#define CONFIG_NAND_OMAP_ECCSCHEME	OMAP_ECC_HAM1_CODE_HW

#define CONFIG_SYS_NAND_U_BOOT_START	CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_NAND_U_BOOT_OFFS	0x80000

#define CONFIG_SPL_TEXT_BASE		0x40200800
#define CONFIG_SPL_MAX_SIZE		(54 * 1024)	/* 8 KB for stack */

/*
 * Use 0x80008000 as TEXT_BASE here for compatibility reasons with the
 * older x-loader implementations. And move the BSS area so that it
 * doesn't overlap with TEXT_BASE.
 */
#define CONFIG_SYS_TEXT_BASE		0x80008000
#define CONFIG_SPL_BSS_START_ADDR	0x80100000
#define CONFIG_SPL_BSS_MAX_SIZE		0x80000		/* 512 KB */

#define CONFIG_SYS_SPL_MALLOC_START	0x80208000
#define CONFIG_SYS_SPL_MALLOC_SIZE	0x100000

/* EEPROM */
#define CONFIG_CMD_EEPROM
#define CONFIG_ENV_EEPROM_IS_ON_I2C
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		1
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	4
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	5
#define CONFIG_SYS_EEPROM_SIZE			256

#define CONFIG_CMD_EEPROM_LAYOUT
#define CONFIG_EEPROM_LAYOUT_HELP_STRING "legacy, v1, v2, v3"

#endif /* __CONFIG_H */