MX31: Add USB Host support to the QONG board
Signed-off-by: Stefano Babic <sbabic@denx.de>
diff --git a/board/davedenx/qong/qong.c b/board/davedenx/qong/qong.c
index efeb0bb..8a81cfc 100644
--- a/board/davedenx/qong/qong.c
+++ b/board/davedenx/qong/qong.c
@@ -25,6 +25,7 @@
#include <netdev.h>
#include <asm/arch/mx31.h>
#include <asm/arch/mx31-regs.h>
+#include <asm/io.h>
#include <nand.h>
#include <fsl_pmic.h>
#include <mxc_gpio.h>
@@ -97,6 +98,38 @@
mx31_gpio_mux(MUX_CSPI2_SCLK__CSPI2_CLK);
mx31_gpio_mux(MUX_CSPI2_SPI_RDY__CSPI2_DATAREADY_B);
+ /* Setup pins for USB2 Host */
+ mx31_gpio_mux(IOMUX_MODE(MUX_CTL_USBH2_CLK, MUX_CTL_FUNC));
+ mx31_gpio_mux(IOMUX_MODE(MUX_CTL_USBH2_DIR, MUX_CTL_FUNC));
+ mx31_gpio_mux(IOMUX_MODE(MUX_CTL_USBH2_NXT, MUX_CTL_FUNC));
+ mx31_gpio_mux(IOMUX_MODE(MUX_CTL_USBH2_STP, MUX_CTL_FUNC));
+ mx31_gpio_mux(IOMUX_MODE(MUX_CTL_USBH2_DATA0, MUX_CTL_FUNC));
+ mx31_gpio_mux(IOMUX_MODE(MUX_CTL_USBH2_DATA1, MUX_CTL_FUNC));
+ mx31_gpio_mux(IOMUX_MODE(MUX_CTL_STXD3, MUX_CTL_FUNC));
+ mx31_gpio_mux(IOMUX_MODE(MUX_CTL_SRXD3, MUX_CTL_FUNC));
+ mx31_gpio_mux(IOMUX_MODE(MUX_CTL_SCK3, MUX_CTL_FUNC));
+ mx31_gpio_mux(IOMUX_MODE(MUX_CTL_SFS3, MUX_CTL_FUNC));
+ mx31_gpio_mux(IOMUX_MODE(MUX_CTL_STXD6, MUX_CTL_FUNC));
+ mx31_gpio_mux(IOMUX_MODE(MUX_CTL_SRXD6, MUX_CTL_FUNC));
+
+#define H2_PAD_CFG (PAD_CTL_DRV_MAX | PAD_CTL_SRE_FAST | PAD_CTL_HYS_CMOS | \
+ PAD_CTL_ODE_CMOS | PAD_CTL_100K_PU)
+
+ mx31_set_pad(MX31_PIN_USBH2_CLK, H2_PAD_CFG);
+ mx31_set_pad(MX31_PIN_USBH2_DIR, H2_PAD_CFG);
+ mx31_set_pad(MX31_PIN_USBH2_NXT, H2_PAD_CFG);
+ mx31_set_pad(MX31_PIN_USBH2_STP, H2_PAD_CFG);
+ mx31_set_pad(MX31_PIN_USBH2_DATA0, H2_PAD_CFG); /* USBH2_DATA0 */
+ mx31_set_pad(MX31_PIN_USBH2_DATA1, H2_PAD_CFG); /* USBH2_DATA1 */
+ mx31_set_pad(MX31_PIN_SRXD6, H2_PAD_CFG); /* USBH2_DATA2 */
+ mx31_set_pad(MX31_PIN_STXD6, H2_PAD_CFG); /* USBH2_DATA3 */
+ mx31_set_pad(MX31_PIN_SFS3, H2_PAD_CFG); /* USBH2_DATA4 */
+ mx31_set_pad(MX31_PIN_SCK3, H2_PAD_CFG); /* USBH2_DATA5 */
+ mx31_set_pad(MX31_PIN_SRXD3, H2_PAD_CFG); /* USBH2_DATA6 */
+ mx31_set_pad(MX31_PIN_STXD3, H2_PAD_CFG); /* USBH2_DATA7 */
+
+ writel(readl((IOMUXC_BASE + 0x8)) | (1 << 11), IOMUXC_BASE + 0x8);
+
return 0;
}
diff --git a/include/configs/qong.h b/include/configs/qong.h
index 0465ff4..b1aca93 100644
--- a/include/configs/qong.h
+++ b/include/configs/qong.h
@@ -89,6 +89,22 @@
#define CONFIG_BMP_16BPP
#define CONFIG_DISPLAY_COM57H5M10XRC
+/* USB */
+#define CONFIG_CMD_USB
+#ifdef CONFIG_CMD_USB
+#define CONFIG_USB_EHCI /* Enable EHCI USB support */
+#define CONFIG_USB_EHCI_MXC
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
+#define CONFIG_MXC_USB_PORT 2
+#define CONFIG_MXC_USB_PORTSC (MXC_EHCI_MODE_ULPI | MXC_EHCI_UTMI_8BIT)
+#define CONFIG_MXC_USB_FLAGS MXC_EHCI_POWER_PINS_ENABLED
+#define CONFIG_EHCI_IS_TDI
+#define CONFIG_USB_STORAGE
+#define CONFIG_DOS_PARTITION
+#define CONFIG_SUPPORT_VFAT
+#define CONFIG_CMD_FAT
+#endif /* CONFIG_CMD_USB */
+
/*
* Reducing the ARP timeout from default 5 seconds to 200ms we speed up the
* initial TFTP transfer, should the user wish one, significantly.
@@ -250,7 +266,7 @@
#define CONFIG_ENV_IS_IN_FLASH 1
#define CONFIG_ENV_SECT_SIZE 0x20000
#define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE
-#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x60000)
+#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x80000)
/* Address and size of Redundant Environment Sector */
#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)