common: move board_f.c prototypes in init.h
Move prototypes for function used in common/board_f.c
from common.h to init.h
Remove weak for arch_reserve_stacks in prototype
(checkpatch issue)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
diff --git a/include/init.h b/include/init.h
index 324fbe0..f57a438 100644
--- a/include/init.h
+++ b/include/init.h
@@ -18,6 +18,7 @@
*/
/* common/board_f.c */
+void board_init_f(ulong dummy);
/**
* arch_cpu_init() - basic cpu-dependent setup for an architecture
@@ -32,6 +33,17 @@
int arch_cpu_init(void);
/**
+ * arch_cpu_init_dm() - init CPU after driver model is available
+ *
+ * This is called immediately after driver model is available before
+ * relocation. This is similar to arch_cpu_init() but is able to reference
+ * devices
+ *
+ * @return 0 if OK, -ve on error
+ */
+int arch_cpu_init_dm(void);
+
+/**
* mach_cpu_init() - SoC/machine dependent CPU setup
*
* This is called after arch_cpu_init(). It should handle any
@@ -43,6 +55,60 @@
*/
int mach_cpu_init(void);
+/**
+ * arch_fsp_init() - perform firmware support package init
+ *
+ * Where U-Boot relies on binary blobs to handle part of the system init, this
+ * function can be used to set up the blobs. This is used on some Intel
+ * platforms.
+ */
+int arch_fsp_init(void);
+
+int dram_init(void);
+
+/**
+ * dram_init_banksize() - Set up DRAM bank sizes
+ *
+ * This can be implemented by boards to set up the DRAM bank information in
+ * gd->bd->bi_dram(). It is called just before relocation, after dram_init()
+ * is called.
+ *
+ * If this is not provided, a default implementation will try to set up a
+ * single bank. It will do this if CONFIG_NR_DRAM_BANKS and
+ * CONFIG_SYS_SDRAM_BASE are set. The bank will have a start address of
+ * CONFIG_SYS_SDRAM_BASE and the size will be determined by a call to
+ * get_effective_memsize().
+ *
+ * @return 0 if OK, -ve on error
+ */
+int dram_init_banksize(void);
+
+/**
+ * Reserve all necessary stacks
+ *
+ * This is used in generic board init sequence in common/board_f.c. Each
+ * architecture could provide this function to tailor the required stacks.
+ *
+ * On entry gd->start_addr_sp is pointing to the suggested top of the stack.
+ * The callee ensures gd->start_add_sp is 16-byte aligned, so architectures
+ * require only this can leave it untouched.
+ *
+ * On exit gd->start_addr_sp and gd->irq_sp should be set to the respective
+ * positions of the stack. The stack pointer(s) will be set to this later.
+ * gd->irq_sp is only required, if the architecture needs it.
+ *
+ * @return 0 if no error
+ */
+int arch_reserve_stacks(void);
+
+int print_cpuinfo(void);
+int timer_init(void);
+int reserve_mmu(void);
+int misc_init_f(void);
+#if defined(CONFIG_DTB_RESELECT)
+int embedded_dtb_select(void);
+#endif
+
/* common/board_r.c */
#endif /* __ASSEMBLY__ */