net: phy: mscc: sync rx/tx delay settings with Linux on vsc85xx
The Linux kernel does set the clock delays to
- 0.2 ns (their default, and lowest, hardware value) if delays should
not be enabled
- 2.0 ns (which causes the data to be sampled at exactly half way between
clock transitions at 1000 Mbps) if delays should be enabled
depending on the interface mode
See https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/drivers/net/phy/mscc/mscc_main.c#n523
So instead of using arbitrary delay values like now, mimic this behaviour.
The behaviour is the same for all of vsc8530/8531/8540/8541 so move that
to a shared function while at it.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
diff --git a/drivers/net/phy/mscc.c b/drivers/net/phy/mscc.c
index 64e9093..d1a643c 100644
--- a/drivers/net/phy/mscc.c
+++ b/drivers/net/phy/mscc.c
@@ -1176,6 +1176,9 @@
rx_clk_out = RX_CLK_OUT_NORMAL;
break;
+ case PHY_INTERFACE_MODE_RGMII_TXID:
+ case PHY_INTERFACE_MODE_RGMII_RXID:
+ case PHY_INTERFACE_MODE_RGMII_ID:
case PHY_INTERFACE_MODE_RGMII:
/* Set Reg23.12:11=2 */
mac_if = MAC_IF_SELECTION_RGMII;
@@ -1259,13 +1262,43 @@
return 0;
}
+static int vsc8531_vsc8541_clk_skew_config(struct phy_device *phydev)
+{
+ enum vsc_phy_rgmii_skew rx_clk_skew = VSC_PHY_RGMII_DELAY_200_PS;
+ enum vsc_phy_rgmii_skew tx_clk_skew = VSC_PHY_RGMII_DELAY_200_PS;
+ u16 reg_val;
+
+ if (phydev->interface == PHY_INTERFACE_MODE_RGMII_RXID ||
+ phydev->interface == PHY_INTERFACE_MODE_RGMII_ID)
+ rx_clk_skew = VSC_PHY_RGMII_DELAY_2000_PS;
+
+ if (phydev->interface == PHY_INTERFACE_MODE_RGMII_TXID ||
+ phydev->interface == PHY_INTERFACE_MODE_RGMII_ID)
+ tx_clk_skew = VSC_PHY_RGMII_DELAY_2000_PS;
+
+ phy_write(phydev, MDIO_DEVAD_NONE, MSCC_EXT_PAGE_ACCESS,
+ MSCC_PHY_PAGE_EXT2);
+ reg_val = phy_read(phydev, MDIO_DEVAD_NONE, MSCC_PHY_RGMII_CNTL_REG);
+
+ /* Reg20E2 - Update RGMII RX_Clk Skews. */
+ reg_val = bitfield_replace(reg_val, RGMII_RX_CLK_DELAY_POS,
+ RGMII_RX_CLK_DELAY_WIDTH, rx_clk_skew);
+ /* Reg20E2 - Update RGMII TX_Clk Skews. */
+ reg_val = bitfield_replace(reg_val, RGMII_TX_CLK_DELAY_POS,
+ RGMII_TX_CLK_DELAY_WIDTH, tx_clk_skew);
+
+ phy_write(phydev, MDIO_DEVAD_NONE, MSCC_PHY_RGMII_CNTL_REG, reg_val);
+ phy_write(phydev, MDIO_DEVAD_NONE, MSCC_EXT_PAGE_ACCESS,
+ MSCC_PHY_PAGE_STD);
+
+ return 0;
+}
+
static int vsc8531_config(struct phy_device *phydev)
{
int retval = -EINVAL;
u16 reg_val;
u16 rmii_clk_out;
- enum vsc_phy_rgmii_skew rx_clk_skew = VSC_PHY_RGMII_DELAY_1700_PS;
- enum vsc_phy_rgmii_skew tx_clk_skew = VSC_PHY_RGMII_DELAY_800_PS;
enum vsc_phy_clk_slew edge_rate = VSC_PHY_CLK_SLEW_RATE_4;
/* For VSC8530/31 and VSC8540/41 the init scripts are the same */
@@ -1275,6 +1308,9 @@
switch (phydev->interface) {
case PHY_INTERFACE_MODE_RMII:
case PHY_INTERFACE_MODE_RGMII:
+ case PHY_INTERFACE_MODE_RGMII_TXID:
+ case PHY_INTERFACE_MODE_RGMII_RXID:
+ case PHY_INTERFACE_MODE_RGMII_ID:
retval = vsc8531_vsc8541_mac_config(phydev);
if (retval != 0)
return retval;
@@ -1291,19 +1327,12 @@
/* Default RMII Clk Output to 0=OFF/1=ON */
rmii_clk_out = 0;
+ retval = vsc8531_vsc8541_clk_skew_config(phydev);
+ if (retval != 0)
+ return retval;
+
phy_write(phydev, MDIO_DEVAD_NONE, MSCC_EXT_PAGE_ACCESS,
MSCC_PHY_PAGE_EXT2);
- reg_val = phy_read(phydev, MDIO_DEVAD_NONE, MSCC_PHY_RGMII_CNTL_REG);
-
- /* Reg20E2 - Update RGMII RX_Clk Skews. */
- reg_val = bitfield_replace(reg_val, RGMII_RX_CLK_DELAY_POS,
- RGMII_RX_CLK_DELAY_WIDTH, rx_clk_skew);
- /* Reg20E2 - Update RGMII TX_Clk Skews. */
- reg_val = bitfield_replace(reg_val, RGMII_TX_CLK_DELAY_POS,
- RGMII_TX_CLK_DELAY_WIDTH, tx_clk_skew);
-
- phy_write(phydev, MDIO_DEVAD_NONE, MSCC_PHY_RGMII_CNTL_REG, reg_val);
-
reg_val = phy_read(phydev, MDIO_DEVAD_NONE, MSCC_PHY_WOL_MAC_CONTROL);
/* Reg27E2 - Update Clk Slew Rate. */
reg_val = bitfield_replace(reg_val, EDGE_RATE_CNTL_POS,
@@ -1329,8 +1358,6 @@
int retval = -EINVAL;
u16 reg_val;
u16 rmii_clk_out;
- enum vsc_phy_rgmii_skew rx_clk_skew = VSC_PHY_RGMII_DELAY_1700_PS;
- enum vsc_phy_rgmii_skew tx_clk_skew = VSC_PHY_RGMII_DELAY_800_PS;
enum vsc_phy_clk_slew edge_rate = VSC_PHY_CLK_SLEW_RATE_4;
/* For VSC8530/31 and VSC8540/41 the init scripts are the same */
@@ -1358,17 +1385,12 @@
/* Default RMII Clk Output to 0=OFF/1=ON */
rmii_clk_out = 0;
+ retval = vsc8531_vsc8541_clk_skew_config(phydev);
+ if (retval != 0)
+ return retval;
+
phy_write(phydev, MDIO_DEVAD_NONE, MSCC_EXT_PAGE_ACCESS,
MSCC_PHY_PAGE_EXT2);
- reg_val = phy_read(phydev, MDIO_DEVAD_NONE, MSCC_PHY_RGMII_CNTL_REG);
- /* Reg20E2 - Update RGMII RX_Clk Skews. */
- reg_val = bitfield_replace(reg_val, RGMII_RX_CLK_DELAY_POS,
- RGMII_RX_CLK_DELAY_WIDTH, rx_clk_skew);
- /* Reg20E2 - Update RGMII TX_Clk Skews. */
- reg_val = bitfield_replace(reg_val, RGMII_TX_CLK_DELAY_POS,
- RGMII_TX_CLK_DELAY_WIDTH, tx_clk_skew);
- phy_write(phydev, MDIO_DEVAD_NONE, MSCC_PHY_RGMII_CNTL_REG, reg_val);
-
reg_val = phy_read(phydev, MDIO_DEVAD_NONE, MSCC_PHY_WOL_MAC_CONTROL);
/* Reg27E2 - Update Clk Slew Rate. */
reg_val = bitfield_replace(reg_val, EDGE_RATE_CNTL_POS,