tegra: Whistler board support
Whistler is a highly configurable Tegra evaluation and development board.
This change adds support for the following specific configuration:
E1120 motherboard
E1108 CPU board
E1116 PMU board
The motherboard configuration switches are set as follows:
SW1=0 SW2=0 SW3=5
S1/S2/S3/S4 all on, except S3 7/8 are off.
Other combinations of daugher boards may work to varying degrees, but will
likely require some SW adjustment.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
diff --git a/MAINTAINERS b/MAINTAINERS
index e55893b..0db7e84 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -914,6 +914,7 @@
ventana Tegra2 (ARM7 & A9 Dual Core)
paz00 Tegra2 (ARM7 & A9 Dual Core)
+ whistler Tegra2 (ARM7 & A9 Dual Core)
Thomas Weber <weber@corscience.de>
diff --git a/board/nvidia/dts/tegra2-whistler.dts b/board/nvidia/dts/tegra2-whistler.dts
new file mode 100644
index 0000000..b22d407
--- /dev/null
+++ b/board/nvidia/dts/tegra2-whistler.dts
@@ -0,0 +1,67 @@
+/dts-v1/;
+
+/include/ ARCH_CPU_DTS
+
+/ {
+ model = "NVIDIA Tegra2 Whistler evaluation board";
+ compatible = "nvidia,whistler", "nvidia,tegra20";
+
+ aliases {
+ i2c0 = "/i2c@7000d000";
+ usb0 = "/usb@c5008000";
+ usb1 = "/usb@c5000000";
+ };
+
+ memory {
+ device_type = "memory";
+ reg = < 0x00000000 0x20000000 >;
+ };
+
+ clocks {
+ osc {
+ clock-frequency = <12000000>;
+ };
+ };
+
+ clock@60006000 {
+ clocks = <&clk_32k &osc>;
+ };
+
+ serial@70006000 {
+ clock-frequency = < 216000000 >;
+ };
+
+ i2c@7000c000 {
+ status = "disabled";
+ };
+
+ i2c@7000c400 {
+ status = "disabled";
+ };
+
+ i2c@7000c500 {
+ status = "disabled";
+ };
+
+ i2c@7000d000 {
+ clock-frequency = <100000>;
+
+ pmic@3c {
+ compatible = "maxim,max8907b";
+ reg = <0x3c>;
+
+ clk_32k: clock {
+ compatible = "fixed-clock";
+ /*
+ * leave out for now due to CPP:
+ * #clock-cells = <0>;
+ */
+ clock-frequency = <32768>;
+ };
+ };
+ };
+
+ usb@c5004000 {
+ status = "disabled";
+ };
+};
diff --git a/board/nvidia/whistler/Makefile b/board/nvidia/whistler/Makefile
new file mode 100644
index 0000000..a910577
--- /dev/null
+++ b/board/nvidia/whistler/Makefile
@@ -0,0 +1,48 @@
+#
+# (C) Copyright 2010-2012
+# NVIDIA Corporation <www.nvidia.com>
+#
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+ifneq ($(OBJTREE),$(SRCTREE))
+$(shell mkdir -p $(obj)../common)
+endif
+
+LIB = $(obj)lib$(BOARD).o
+
+COBJS := $(BOARD).o
+
+SRCS := $(COBJS:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS))
+
+$(LIB): $(obj).depend $(OBJS)
+ $(call cmd_link_o_target, $(OBJS))
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/nvidia/whistler/whistler.c b/board/nvidia/whistler/whistler.c
new file mode 100644
index 0000000..1c2f33f
--- /dev/null
+++ b/board/nvidia/whistler/whistler.c
@@ -0,0 +1,116 @@
+/*
+ * (C) Copyright 2010-2012
+ * NVIDIA Corporation <www.nvidia.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <i2c.h>
+#include <asm/io.h>
+#include <asm/arch/tegra2.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/funcmux.h>
+#include <asm/arch/pinmux.h>
+#include <asm/arch/mmc.h>
+#include <asm/gpio.h>
+#ifdef CONFIG_TEGRA2_MMC
+#include <mmc.h>
+#endif
+
+/*
+ * Routine: gpio_config_uart
+ * Description: Does nothing on Whistler - no UART-related GPIOs.
+ */
+void gpio_config_uart(void)
+{
+}
+
+/*
+ * Routine: pin_mux_mmc
+ * Description: setup the pin muxes/tristate values for the SDMMC(s)
+ */
+static void pin_mux_mmc(void)
+{
+ funcmux_select(PERIPH_ID_SDMMC3, FUNCMUX_SDMMC3_SDB_SLXA_8BIT);
+ funcmux_select(PERIPH_ID_SDMMC4, FUNCMUX_SDMMC4_ATC_ATD_8BIT);
+}
+
+/* this is a weak define that we are overriding */
+int board_mmc_init(bd_t *bd)
+{
+ uchar val;
+ int ret;
+
+ debug("board_mmc_init called\n");
+
+ /* Turn on MAX8907B LDO12 to 2.8V for J40 power */
+ ret = i2c_set_bus_num(0);
+ if (ret)
+ printf("i2c_set_bus_num failed: %d\n", ret);
+ val = 0x29;
+ ret = i2c_write(0x3c, 0x46, 1, &val, 1);
+ if (ret)
+ printf("i2c_write 0 0x3c 0x46 failed: %d\n", ret);
+ val = 0x00;
+ ret = i2c_write(0x3c, 0x45, 1, &val, 1);
+ if (ret)
+ printf("i2c_write 0 0x3c 0x45 failed: %d\n", ret);
+ val = 0x1f;
+ ret = i2c_write(0x3c, 0x44, 1, &val, 1);
+ if (ret)
+ printf("i2c_write 0 0x3c 0x44 failed: %d\n", ret);
+
+ /* Enable muxes, etc. for SDMMC controllers */
+ pin_mux_mmc();
+
+ /* init dev 0 (SDMMC4), (J29 "HSMMC") with 8-bit bus */
+ tegra2_mmc_init(0, 8, -1, -1);
+
+ /* init dev 1 (SDMMC3), (J40 "SDIO3") with 8-bit bus */
+ tegra2_mmc_init(1, 8, -1, -1);
+
+ return 0;
+}
+
+/* this is a weak define that we are overriding */
+void pin_mux_usb(void)
+{
+ uchar val;
+ int ret;
+
+ /*
+ * This is a hack. This should be represented in DT using the
+ * vbus-gpio property. However, U-Boot's DT support doesn't
+ * support any GPIO controller other than the Tegra's yet.
+ */
+
+ /* Turn on TAC6416's GPIO 0+1 for USB1/3's VBUS */
+ ret = i2c_set_bus_num(0);
+ if (ret)
+ printf("i2c_set_bus_num failed: %d\n", ret);
+ val = 0x03;
+ ret = i2c_write(0x20, 2, 1, &val, 1);
+ if (ret)
+ printf("i2c_write 0 0x20 2 failed: %d\n", ret);
+ val = 0xfc;
+ ret = i2c_write(0x20, 6, 1, &val, 1);
+ if (ret)
+ printf("i2c_write 0 0x20 6 failed: %d\n", ret);
+}
diff --git a/boards.cfg b/boards.cfg
index a723f67..055dbbc 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -231,6 +231,7 @@
harmony arm armv7 harmony nvidia tegra2
seaboard arm armv7 seaboard nvidia tegra2
ventana arm armv7 ventana nvidia tegra2
+whistler arm armv7 whistler nvidia tegra2
u8500_href arm armv7 u8500 st-ericsson u8500
actux1_4_16 arm ixp actux1 - - actux1:FLASH2X2
actux1_4_32 arm ixp actux1 - - actux1:FLASH2X2,RAM_32MB
diff --git a/include/configs/whistler.h b/include/configs/whistler.h
new file mode 100644
index 0000000..6b9ef98
--- /dev/null
+++ b/include/configs/whistler.h
@@ -0,0 +1,90 @@
+/*
+ * (C) Copyright 2010-2012
+ * NVIDIA Corporation <www.nvidia.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#include <asm/sizes.h>
+#include "tegra2-common.h"
+
+/* Enable fdt support for Whistler. Flash the image in u-boot-dtb.bin */
+#define CONFIG_DEFAULT_DEVICE_TREE tegra2-whistler
+#define CONFIG_OF_CONTROL
+#define CONFIG_OF_SEPARATE
+
+/* High-level configuration options */
+#define TEGRA2_SYSMEM "mem=512M@0M"
+#define V_PROMPT "Tegra2 (Whistler) # "
+#define CONFIG_TEGRA2_BOARD_STRING "NVIDIA Whistler"
+
+/* Board-specific serial config */
+#define CONFIG_SERIAL_MULTI
+#define CONFIG_TEGRA2_ENABLE_UARTA
+#define CONFIG_TEGRA2_UARTA_UAA_UAB
+#define CONFIG_SYS_NS16550_COM1 NV_PA_APB_UARTA_BASE
+
+#define CONFIG_MACH_TYPE MACH_TYPE_WHISTLER
+#define CONFIG_SYS_BOARD_ODMDATA 0x2B080105 /* lp?, 512MB, UARTA */
+
+#define CONFIG_BOARD_EARLY_INIT_F
+
+/* I2C */
+#define CONFIG_TEGRA_I2C
+#define CONFIG_SYS_I2C_INIT_BOARD
+#define CONFIG_I2C_MULTI_BUS
+#define CONFIG_SYS_MAX_I2C_BUS 4
+#define CONFIG_SYS_I2C_SPEED 100000
+#define CONFIG_CMD_I2C
+
+/* SD/MMC */
+#define CONFIG_MMC
+#define CONFIG_GENERIC_MMC
+#define CONFIG_TEGRA2_MMC
+#define CONFIG_CMD_MMC
+
+#define CONFIG_DOS_PARTITION
+#define CONFIG_EFI_PARTITION
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
+
+/* Environment not stored */
+#define CONFIG_ENV_IS_NOWHERE
+
+/* USB Host support */
+#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_TEGRA
+#define CONFIG_USB_STORAGE
+#define CONFIG_CMD_USB
+#define CONFIG_USB_HOST_ETHER
+#define CONFIG_USB_ETHER_SMSC95XX
+#define CONFIG_USB_ETHER_ASIX
+#define CONFIG_USB_HOST_ETHER
+#define CONFIG_USB_ETHER_SMSC95XX
+#define CONFIG_USB_ETHER_ASIX
+
+#define CONFIG_CMD_NET /* bootp, tftpboot, rarpboot */
+#define CONFIG_CMD_NFS /* NFS support */
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_DHCP
+
+#endif /* __CONFIG_H */