ARM: kirkwood: add db-88f6281-bp board
This is Marvell's Kirkwood development board. It has the following
features
- 512M DDR2
- 2 PCI connectors
- 1 x1 PCI-e interface
- 1 Gigabit Ethernet Port
- 2 SATA Ports
- USB 2.0 Interface
- SDIO
- 128M NAND Flash
- 16M SPI Flash
It can be strapped to boot from SPI or NAND so there are two defconfigs
(one per boot media).
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
diff --git a/include/configs/db-88f6281-bp.h b/include/configs/db-88f6281-bp.h
new file mode 100644
index 0000000..680de8f
--- /dev/null
+++ b/include/configs/db-88f6281-bp.h
@@ -0,0 +1,99 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+
+#ifndef _CONFIG_DB_88F6281_BP_H
+#define _CONFIG_DB_88F6281_BP_H
+
+/*
+ * High Level Configuration Options (easy to change)
+ */
+#define CONFIG_FEROCEON_88FR131 1 /* CPU Core subversion */
+#define CONFIG_KW88F6281 1 /* SOC Name */
+#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */
+#define CONFIG_SYS_TCLK 166666667
+#define CONFIG_SYS_KWD_CONFIG $(CONFIG_BOARDDIR)/kwbimage.cfg
+#define CONFIG_BUILD_TARGET "u-boot.kwb"
+
+/* additions for new ARM relocation support */
+#define CONFIG_SYS_SDRAM_BASE 0x00000000
+
+#define CONFIG_KIRKWOOD_EGIGA_INIT /* Enable GbePort0/1 for kernel */
+#define CONFIG_KIRKWOOD_PCIE_INIT /* Enable PCIE Port0 */
+#define CONFIG_KIRKWOOD_RGMII_PAD_1V8 /* Set RGMII Pad voltage to 1.8V */
+#define CONFIG_KIRKWOOD_GPIO 1
+
+/*
+ * NS16550 Configuration
+ */
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE (-4)
+#define CONFIG_SYS_NS16550_CLK CONFIG_SYS_TCLK
+#define CONFIG_SYS_NS16550_COM1 KW_UART0_BASE
+
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
+/*
+ * Serial Port configuration
+ * The following definitions let you select what serial you want to use
+ * for your console driver.
+ */
+
+#define CONFIG_CONS_INDEX 1 /* Console on UART0 */
+
+/*
+ * Environment variables configurations
+ */
+#define CONFIG_ENV_SPI_BUS 0
+#define CONFIG_ENV_SPI_CS 0
+#define CONFIG_ENV_SPI_MAX_HZ 20000000 /* 20Mhz */
+#define CONFIG_ENV_SPI_MODE CONFIG_SF_DEFAULT_MODE
+#define CONFIG_ENV_SECT_SIZE 0x40000 /* 256K */
+#define CONFIG_ENV_SIZE 0x01000
+#define CONFIG_ENV_OFFSET 0xC0000
+
+/*
+ * U-Boot bootcode configuration
+ */
+
+#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for monitor */
+#define CONFIG_SYS_MALLOC_LEN (4 << 20) /* Reserve 4.0 MB for malloc */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Mem map for Linux*/
+
+/* size in bytes reserved for initial data */
+
+#include <asm/arch/config.h>
+/* There is no PHY directly connected so don't ask it for link status */
+#undef CONFIG_SYS_FAULT_ECHO_LINK_DOWN
+
+/*
+ * Other required minimal configurations
+ */
+#define CONFIG_ARCH_CPU_INIT /* call arch_cpu_init() */
+#define CONFIG_SYS_MEMTEST_START 0x00400000 /* 4M */
+#define CONFIG_SYS_MEMTEST_END 0x007fffff /* (_8M - 1) */
+#define CONFIG_SYS_RESET_ADDRESS 0xffff0000 /* Rst Vector Adr */
+
+/*
+ * SDIO/MMC Card Configuration
+ */
+#ifdef CONFIG_CMD_MMC
+#define CONFIG_MVEBU_MMC
+#define CONFIG_SYS_MMC_BASE KW_SDIO_BASE
+#endif /* CONFIG_CMD_MMC */
+
+/*
+ * SATA Driver configuration
+ */
+#ifdef CONFIG_MVSATA_IDE
+#define CONFIG_SYS_ATA_IDE0_OFFSET MV_SATA_PORT0_OFFSET
+#endif /*CONFIG_MVSATA_IDE*/
+
+#define CONFIG_SYS_LOAD_ADDR 0x1000000 /* default location for tftp and bootm */
+
+#define CONFIG_SYS_DCACHE_OFF
+
+#endif /* _CONFIG_DB_88F6281_BP_H */