ppc4xx: Big cleanup of PPC4xx defines
This patch cleans up multiple issues of the 4xx register (mostly
DCR, SDR, CPR, etc) definitions:
- Change lower case defines to upper case (plb4_acr -> PLB4_ACR)
- Change the defines to better match the names from the
user's manuals (e.g. cprpllc -> CPR0_PLLC)
- Removal of some unused defines
Please test this patch intensive on your PPC4xx platform. Even though
I tried not to break anything and tested successfully on multiple
4xx AMCC platforms, testing on custom platforms is recommended.
Signed-off-by: Stefan Roese <sr@denx.de>
diff --git a/board/netstal/hcu4/hcu4.c b/board/netstal/hcu4/hcu4.c
index aa8a097..40bec8e 100644
--- a/board/netstal/hcu4/hcu4.c
+++ b/board/netstal/hcu4/hcu4.c
@@ -92,7 +92,7 @@
u16 index = boardVersReg & 0x0f;
/* Cannot be done in board_early_init */
- mtdcr(cntrl0, CPC0_CR0_VALUE);
+ mtdcr(CPC0_CR0, CPC0_CR0_VALUE);
/* Force /RTS to active. The board it not wired quite
* correctly to use cts/rtc flow control, so just force the
diff --git a/board/netstal/hcu5/hcu5.c b/board/netstal/hcu5/hcu5.c
index 5eb33d3..836c034 100644
--- a/board/netstal/hcu5/hcu5.c
+++ b/board/netstal/hcu5/hcu5.c
@@ -94,8 +94,8 @@
}
mtsdr(SDR0_CP440, 0x0EAAEA02); /* [Nto1] = 1*/
#endif
- mtdcr(ebccfga, xbcfg);
- mtdcr(ebccfgd, 0xb8400000);
+ mtdcr(EBC0_CFGADDR, EBC0_CFG);
+ mtdcr(EBC0_CFGDATA, 0xb8400000);
/*
* Setup the GPIO pins
@@ -152,8 +152,8 @@
mtdcr(uic2tr, 0x00000000); /* per ref-board manual */
mtdcr(uic2vr, 0x00000000); /* int31 highest, base=0x000 */
mtdcr(uic2sr, 0xffffffff); /* clear all */
- mtsdr(sdr_pfc0, 0x00003E00); /* Pin function: */
- mtsdr(sdr_pfc1, 0x00848000); /* Pin function: UART0 has 4 pins */
+ mtsdr(SDR0_PFC0, 0x00003E00); /* Pin function: */
+ mtsdr(SDR0_PFC1, 0x00848000); /* Pin function: UART0 has 4 pins */
/* setup BOOT FLASH */
mtsdr(SDR0_CUST0, 0xC0082350);
@@ -324,7 +324,7 @@
{
u32 reg;
- mfsdr(sdr_pci0, reg);
+ mfsdr(SDR0_PCI0, reg);
return (reg & SDR0_XCR_PAE_MASK);
}
@@ -350,28 +350,28 @@
* Set priority for all PLB3 devices to 0.
* Set PLB3 arbiter to fair mode.
*/
- mfsdr(sdr_amp1, addr);
- mtsdr(sdr_amp1, (addr & 0x000000FF) | 0x0000FF00);
- addr = mfdcr(plb3_acr);
- mtdcr(plb3_acr, addr | 0x80000000); /* Sequoia */
+ mfsdr(SD0_AMP1, addr);
+ mtsdr(SD0_AMP1, (addr & 0x000000FF) | 0x0000FF00);
+ addr = mfdcr(PLB3_ACR);
+ mtdcr(PLB3_ACR, addr | 0x80000000); /* Sequoia */
/*
* Set priority for all PLB4 devices to 0.
*/
- mfsdr(sdr_amp0, addr);
- mtsdr(sdr_amp0, (addr & 0x000000FF) | 0x0000FF00);
- addr = mfdcr(plb4_acr) | 0xa0000000; /* Was 0x8---- */
- mtdcr(plb4_acr, addr); /* Sequoia */
+ mfsdr(SD0_AMP0, addr);
+ mtsdr(SD0_AMP0, (addr & 0x000000FF) | 0x0000FF00);
+ addr = mfdcr(PLB4_ACR) | 0xa0000000; /* Was 0x8---- */
+ mtdcr(PLB4_ACR, addr); /* Sequoia */
/*
* As of errata version 0.4, CHIP_8: Incorrect Write to DDR SDRAM.
* Workaround: Disable write pipelining to DDR SDRAM by setting
* PLB0_ACR[WRP] = 0.
*/
- mtdcr(plb0_acr, 0); /* PATCH HAB: WRITE PIPELINING OFF */
+ mtdcr(PLB0_ACR, 0); /* PATCH HAB: WRITE PIPELINING OFF */
/* Segment1 */
- mtdcr(plb1_acr, 0); /* PATCH HAB: WRITE PIPELINING OFF */
+ mtdcr(PLB1_ACR, 0); /* PATCH HAB: WRITE PIPELINING OFF */
return board_with_pci();
}
diff --git a/board/netstal/hcu5/sdram.c b/board/netstal/hcu5/sdram.c
index 5c2ec35..0546cd7 100644
--- a/board/netstal/hcu5/sdram.c
+++ b/board/netstal/hcu5/sdram.c
@@ -89,11 +89,11 @@
/* -----------------------------------------------------------+
* Wait for the DCC master delay line to finish calibration
* ----------------------------------------------------------*/
- mtdcr(memcfga, DDR0_17);
+ mtdcr(SDRAM0_CFGADDR, DDR0_17);
val = DDR0_17_DLLLOCKREG_UNLOCKED;
while (wait != 0xffff) {
- val = mfdcr(memcfgd);
+ val = mfdcr(SDRAM0_CFGDATA);
if ((val & DDR0_17_DLLLOCKREG_MASK) ==
DDR0_17_DLLLOCKREG_LOCKED)
/* dlllockreg bit on */
diff --git a/board/netstal/mcu25/mcu25.c b/board/netstal/mcu25/mcu25.c
index 67c1b0b..9054282 100644
--- a/board/netstal/mcu25/mcu25.c
+++ b/board/netstal/mcu25/mcu25.c
@@ -71,8 +71,8 @@
mtdcr(uictr, 0x00000000); /* set int trigger levels */
mtdcr(uicsr, 0xFFFFFFFF); /* clear all ints */
- mtdcr(cntrl1, CPC0_CR1_VALUE);
- mtdcr(ecr, 0x60606000);
+ mtdcr(CPC0_CR1, CPC0_CR1_VALUE);
+ mtdcr(CPC0_ECR, 0x60606000);
mtdcr(CPC0_EIRR, 0x7C000000);
out32(GPIO0_OR, CONFIG_SYS_GPIO0_OR );
out32(GPIO0_TCR, CONFIG_SYS_GPIO0_TCR);
@@ -103,7 +103,7 @@
u16 index = boardVersReg & 0xf0;
/* Cannot be done in board_early_init */
- mtdcr(cntrl0, CPC0_CR0_VALUE);
+ mtdcr(CPC0_CR0, CPC0_CR0_VALUE);
/* Force /RTS to active. The board it not wired quite
* correctly to use cts/rtc flow control, so just force the