Merge git://git.denx.de/u-boot-ti
diff --git a/arch/arm/cpu/armv7/am33xx/sys_info.c b/arch/arm/cpu/armv7/am33xx/sys_info.c
index 2ce682f..781d83f 100644
--- a/arch/arm/cpu/armv7/am33xx/sys_info.c
+++ b/arch/arm/cpu/armv7/am33xx/sys_info.c
@@ -18,6 +18,7 @@
#include <asm/arch/cpu.h>
#include <asm/arch/clock.h>
#include <power/tps65910.h>
+#include <linux/compiler.h>
struct ctrl_stat *cstat = (struct ctrl_stat *)CTRL_BASE;
@@ -51,11 +52,11 @@
/**
* get_board_rev() - setup to pass kernel board revision information
- * returns:(bit[0-3] sub version, higher bit[7-4] is higher version)
+ * returns: 0 for the ATAG REVISION tag value.
*/
-u32 get_board_rev(void)
+u32 __weak get_board_rev(void)
{
- return BOARD_REV_ID;
+ return 0;
}
/**
diff --git a/arch/arm/cpu/armv7/omap3/Kconfig b/arch/arm/cpu/armv7/omap3/Kconfig
index c215404..a029379 100644
--- a/arch/arm/cpu/armv7/omap3/Kconfig
+++ b/arch/arm/cpu/armv7/omap3/Kconfig
@@ -22,6 +22,9 @@
bool "CompuLab CM-T3530 and CM-T3730 boards"
select SUPPORT_SPL
+config TARGET_CM_T3517
+ bool "CompuLab CM-T3517 boards"
+
config TARGET_DEVKIT8000
bool "TimLL OMAP3 Devkit8000"
select SUPPORT_SPL
@@ -98,6 +101,7 @@
source "board/ti/sdp3430/Kconfig"
source "board/ti/beagle/Kconfig"
source "board/compulab/cm_t35/Kconfig"
+source "board/compulab/cm_t3517/Kconfig"
source "board/timll/devkit8000/Kconfig"
source "board/ti/evm/Kconfig"
source "board/isee/igep00x0/Kconfig"
diff --git a/arch/arm/include/asm/arch-am33xx/sys_proto.h b/arch/arm/include/asm/arch-am33xx/sys_proto.h
index 33a82fc..7eacf27 100644
--- a/arch/arm/include/asm/arch-am33xx/sys_proto.h
+++ b/arch/arm/include/asm/arch-am33xx/sys_proto.h
@@ -14,8 +14,6 @@
#include <asm/ti-common/sys_proto.h>
#include <asm/arch/cpu.h>
-#define BOARD_REV_ID 0x0
-
u32 get_cpu_rev(void);
u32 get_sysboot_value(void);
diff --git a/arch/arm/include/asm/arch-keystone/hardware-k2e.h b/arch/arm/include/asm/arch-keystone/hardware-k2e.h
index 9512756..df49995 100644
--- a/arch/arm/include/asm/arch-keystone/hardware-k2e.h
+++ b/arch/arm/include/asm/arch-keystone/hardware-k2e.h
@@ -57,8 +57,6 @@
#define KS2_NETCP_PDMA_SCHED_BASE 0x24186100
#define KS2_NETCP_PDMA_RX_FLOW_BASE 0x24189000
#define KS2_NETCP_PDMA_RX_FLOW_NUM 96
-#define KS2_NETCP_PDMA_RX_FREE_QUEUE 4001
-#define KS2_NETCP_PDMA_RX_RCV_QUEUE 4002
#define KS2_NETCP_PDMA_TX_SND_QUEUE 896
/* NETCP */
diff --git a/arch/arm/include/asm/arch-keystone/hardware-k2hk.h b/arch/arm/include/asm/arch-keystone/hardware-k2hk.h
index 5a9ea4f..195c0d3 100644
--- a/arch/arm/include/asm/arch-keystone/hardware-k2hk.h
+++ b/arch/arm/include/asm/arch-keystone/hardware-k2hk.h
@@ -98,8 +98,6 @@
#define KS2_NETCP_PDMA_SCHED_BASE 0x02004c00
#define KS2_NETCP_PDMA_RX_FLOW_BASE 0x02005000
#define KS2_NETCP_PDMA_RX_FLOW_NUM 32
-#define KS2_NETCP_PDMA_RX_FREE_QUEUE 4001
-#define KS2_NETCP_PDMA_RX_RCV_QUEUE 4002
#define KS2_NETCP_PDMA_TX_SND_QUEUE 648
/* NETCP */
diff --git a/arch/arm/include/asm/arch-keystone/hardware-k2l.h b/arch/arm/include/asm/arch-keystone/hardware-k2l.h
index 05532ad..4f1197e 100644
--- a/arch/arm/include/asm/arch-keystone/hardware-k2l.h
+++ b/arch/arm/include/asm/arch-keystone/hardware-k2l.h
@@ -84,6 +84,10 @@
/* OSR memory size */
#define KS2_OSR_SIZE 0x100000
+/* SGMII SerDes */
+#define KS2_SGMII_SERDES2_BASE 0x02320000
+#define KS2_LANES_PER_SGMII_SERDES 2
+
/* Number of DSP cores */
#define KS2_NUM_DSPS 4
@@ -98,4 +102,7 @@
#define KS2_NETCP_PDMA_RX_FLOW_NUM 96
#define KS2_NETCP_PDMA_TX_SND_QUEUE 896
+/* NETCP */
+#define KS2_NETCP_BASE 0x26000000
+
#endif /* __ASM_ARCH_HARDWARE_K2L_H */
diff --git a/arch/arm/include/asm/arch-keystone/hardware.h b/arch/arm/include/asm/arch-keystone/hardware.h
index c6a54d8..be22bdb 100644
--- a/arch/arm/include/asm/arch-keystone/hardware.h
+++ b/arch/arm/include/asm/arch-keystone/hardware.h
@@ -122,6 +122,10 @@
#define KS2_EDMA_QEESR 0x108c
#define KS2_EDMA_PARAM_1(x) (0x4020 + (4 * x))
+/* NETCP pktdma */
+#define KS2_NETCP_PDMA_RX_FREE_QUEUE 4001
+#define KS2_NETCP_PDMA_RX_RCV_QUEUE 4002
+
/* Chip Interrupt Controller */
#define KS2_CIC2_BASE 0x02608000
diff --git a/board/compulab/cm_t35/cm_t35.c b/board/compulab/cm_t35/cm_t35.c
index d0b0930..886c723 100644
--- a/board/compulab/cm_t35/cm_t35.c
+++ b/board/compulab/cm_t35/cm_t35.c
@@ -19,12 +19,11 @@
#include <i2c.h>
#include <usb.h>
#include <mmc.h>
-#include <nand.h>
#include <twl4030.h>
-#include <bmp_layout.h>
#include <linux/compiler.h>
#include <asm/io.h>
+#include <asm/errno.h>
#include <asm/arch/mem.h>
#include <asm/arch/mux.h>
#include <asm/arch/mmc_host_def.h>
@@ -33,6 +32,7 @@
#include <asm/ehci-omap.h>
#include <asm/gpio.h>
+#include "../common/common.h"
#include "../common/eeprom.h"
DECLARE_GLOBAL_DATA_PTR;
@@ -43,58 +43,6 @@
"NAND",
};
-static u32 gpmc_net_config[GPMC_MAX_REG] = {
- NET_GPMC_CONFIG1,
- NET_GPMC_CONFIG2,
- NET_GPMC_CONFIG3,
- NET_GPMC_CONFIG4,
- NET_GPMC_CONFIG5,
- NET_GPMC_CONFIG6,
- 0
-};
-
-#ifdef CONFIG_LCD
-#ifdef CONFIG_CMD_NAND
-static int splash_load_from_nand(u32 bmp_load_addr)
-{
- struct bmp_header *bmp_hdr;
- int res, splash_screen_nand_offset = 0x100000;
- size_t bmp_size, bmp_header_size = sizeof(struct bmp_header);
-
- if (bmp_load_addr + bmp_header_size >= gd->start_addr_sp)
- goto splash_address_too_high;
-
- res = nand_read_skip_bad(&nand_info[nand_curr_device],
- splash_screen_nand_offset, &bmp_header_size,
- NULL, nand_info[nand_curr_device].size,
- (u_char *)bmp_load_addr);
- if (res < 0)
- return res;
-
- bmp_hdr = (struct bmp_header *)bmp_load_addr;
- bmp_size = le32_to_cpu(bmp_hdr->file_size);
-
- if (bmp_load_addr + bmp_size >= gd->start_addr_sp)
- goto splash_address_too_high;
-
- return nand_read_skip_bad(&nand_info[nand_curr_device],
- splash_screen_nand_offset, &bmp_size,
- NULL, nand_info[nand_curr_device].size,
- (u_char *)bmp_load_addr);
-
-splash_address_too_high:
- printf("Error: splashimage address too high. Data overwrites U-Boot "
- "and/or placed beyond DRAM boundaries.\n");
-
- return -1;
-}
-#else
-static inline int splash_load_from_nand(void)
-{
- return -1;
-}
-#endif /* CONFIG_CMD_NAND */
-
#ifdef CONFIG_SPL_BUILD
/*
* Routine: get_board_mem_timings
@@ -111,24 +59,12 @@
}
#endif
+#define CM_T35_SPLASH_NAND_OFFSET 0x100000
+
int splash_screen_prepare(void)
{
- char *env_splashimage_value;
- u32 bmp_load_addr;
-
- env_splashimage_value = getenv("splashimage");
- if (env_splashimage_value == NULL)
- return -1;
-
- bmp_load_addr = simple_strtoul(env_splashimage_value, 0, 16);
- if (bmp_load_addr == 0) {
- printf("Error: bad splashimage address specified\n");
- return -1;
- }
-
- return splash_load_from_nand(bmp_load_addr);
+ return cl_splash_screen_prepare(CM_T35_SPLASH_NAND_OFFSET);
}
-#endif /* CONFIG_LCD */
/*
* Routine: board_init
@@ -154,34 +90,18 @@
return 0;
}
-static u32 cm_t3x_rev;
-
/*
* Routine: get_board_rev
* Description: read system revision
*/
u32 get_board_rev(void)
{
- if (!cm_t3x_rev)
- cm_t3x_rev = cl_eeprom_get_board_rev();
-
- return cm_t3x_rev;
+ return cl_eeprom_get_board_rev();
};
-/*
- * Routine: misc_init_r
- * Description: display die ID
- */
int misc_init_r(void)
{
- u32 board_rev = get_board_rev();
- u32 rev_major = board_rev / 100;
- u32 rev_minor = board_rev - (rev_major * 100);
-
- if ((rev_minor / 10) * 10 == rev_minor)
- rev_minor = rev_minor / 10;
-
- printf("PCB: %u.%u\n", rev_major, rev_minor);
+ cl_print_pcb_info();
dieid_num_r();
return 0;
@@ -462,37 +382,12 @@
}
#endif
-/*
- * Routine: setup_net_chip_gmpc
- * Description: Setting up the configuration GPMC registers specific to the
- * Ethernet hardware.
- */
-static void setup_net_chip_gmpc(void)
-{
- struct ctrl *ctrl_base = (struct ctrl *)OMAP34XX_CTRL_BASE;
-
- enable_gpmc_cs_config(gpmc_net_config, &gpmc_cfg->cs[5],
- CM_T3X_SMC911X_BASE, GPMC_SIZE_16M);
- enable_gpmc_cs_config(gpmc_net_config, &gpmc_cfg->cs[4],
- SB_T35_SMC911X_BASE, GPMC_SIZE_16M);
-
- /* Enable off mode for NWE in PADCONF_GPMC_NWE register */
- writew(readw(&ctrl_base->gpmc_nwe) | 0x0E00, &ctrl_base->gpmc_nwe);
-
- /* Enable off mode for NOE in PADCONF_GPMC_NADV_ALE register */
- writew(readw(&ctrl_base->gpmc_noe) | 0x0E00, &ctrl_base->gpmc_noe);
-
- /* Enable off mode for ALE in PADCONF_GPMC_NADV_ALE register */
- writew(readw(&ctrl_base->gpmc_nadv_ale) | 0x0E00,
- &ctrl_base->gpmc_nadv_ale);
-}
-
#ifdef CONFIG_SYS_I2C_OMAP34XX
/*
* Routine: reset_net_chip
* Description: reset the Ethernet controller via TPS65930 GPIO
*/
-static void reset_net_chip(void)
+static int cm_t3x_reset_net_chip(int gpio)
{
/* Set GPIO1 of TPS65930 as output */
twl4030_i2c_write_u8(TWL4030_CHIP_GPIO, TWL4030_BASEADD_GPIO + 0x03,
@@ -507,9 +402,10 @@
twl4030_i2c_write_u8(TWL4030_CHIP_GPIO, TWL4030_BASEADD_GPIO + 0x0C,
0x02);
mdelay(1);
+ return 0;
}
#else
-static inline void reset_net_chip(void) {}
+static inline int cm_t3x_reset_net_chip(int gpio) { return 0; }
#endif
#ifdef CONFIG_SMC911X
@@ -536,7 +432,6 @@
return eth_setenv_enetaddr("ethaddr", enetaddr);
}
-
/*
* Routine: board_eth_init
* Description: initialize module and base-board Ethernet chips
@@ -545,18 +440,16 @@
{
int rc = 0, rc1 = 0;
- setup_net_chip_gmpc();
- reset_net_chip();
-
rc1 = handle_mac_address();
if (rc1)
printf("No MAC address found! ");
- rc1 = smc911x_initialize(0, CM_T3X_SMC911X_BASE);
+ rc1 = cl_omap3_smc911x_init(0, 5, CM_T3X_SMC911X_BASE,
+ cm_t3x_reset_net_chip, -EINVAL);
if (rc1 > 0)
rc++;
- rc1 = smc911x_initialize(1, SB_T35_SMC911X_BASE);
+ rc1 = cl_omap3_smc911x_init(1, 4, SB_T35_SMC911X_BASE, NULL, -EINVAL);
if (rc1 > 0)
rc++;
@@ -564,16 +457,6 @@
}
#endif
-void __weak get_board_serial(struct tag_serialnr *serialnr)
-{
- /*
- * This corresponds to what happens when we can communicate with the
- * eeprom but don't get a valid board serial value.
- */
- serialnr->low = 0;
- serialnr->high = 0;
-};
-
#ifdef CONFIG_USB_EHCI_OMAP
struct omap_usbhs_board_data usbhs_bdata = {
.port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
@@ -583,21 +466,12 @@
#define SB_T35_USB_HUB_RESET_GPIO 167
int ehci_hcd_init(int index, enum usb_init_type init,
- struct ehci_hccr **hccr, struct ehci_hcor **hcor)
+ struct ehci_hccr **hccr, struct ehci_hcor **hcor)
{
u8 val;
int offset;
- if (gpio_request(SB_T35_USB_HUB_RESET_GPIO, "SB-T35 usb hub reset")) {
- printf("Error: can't obtain GPIO %d for SB-T35 usb hub reset",
- SB_T35_USB_HUB_RESET_GPIO);
- return -1;
- }
-
- gpio_direction_output(SB_T35_USB_HUB_RESET_GPIO, 0);
- udelay(10);
- gpio_set_value(SB_T35_USB_HUB_RESET_GPIO, 1);
- udelay(1000);
+ cl_usb_hub_init(SB_T35_USB_HUB_RESET_GPIO, "sb-t35 hub rst");
offset = TWL4030_BASEADD_GPIO + TWL4030_GPIO_GPIODATADIR1;
twl4030_i2c_read_u8(TWL4030_CHIP_GPIO, offset, &val);
@@ -614,6 +488,7 @@
int ehci_hcd_stop(void)
{
+ cl_usb_hub_deinit(SB_T35_USB_HUB_RESET_GPIO);
return omap_ehci_hcd_stop();
}
#endif /* CONFIG_USB_EHCI_OMAP */
diff --git a/board/compulab/cm_t3517/Kconfig b/board/compulab/cm_t3517/Kconfig
new file mode 100644
index 0000000..2f5473d
--- /dev/null
+++ b/board/compulab/cm_t3517/Kconfig
@@ -0,0 +1,12 @@
+if TARGET_CM_T3517
+
+config SYS_BOARD
+ default "cm_t3517"
+
+config SYS_VENDOR
+ default "compulab"
+
+config SYS_CONFIG_NAME
+ default "cm_t3517"
+
+endif
diff --git a/board/compulab/cm_t3517/MAINTAINERS b/board/compulab/cm_t3517/MAINTAINERS
new file mode 100644
index 0000000..fbb6882
--- /dev/null
+++ b/board/compulab/cm_t3517/MAINTAINERS
@@ -0,0 +1,6 @@
+CM_T3517 BOARD
+M: Igor Grinberg <grinberg@compulab.co.il>
+S: Maintained
+F: board/compulab/cm_t3517/
+F: include/configs/cm_t3517.h
+F: configs/cm_t3517_defconfig
diff --git a/board/compulab/cm_t3517/Makefile b/board/compulab/cm_t3517/Makefile
new file mode 100644
index 0000000..4f0db01
--- /dev/null
+++ b/board/compulab/cm_t3517/Makefile
@@ -0,0 +1,9 @@
+#
+# (C) Copyright 2014 CompuLab, Ltd. <www.compulab.co.il>
+#
+# Authors: Igor Grinberg <grinberg@compulab.co.il>
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+obj-y += cm_t3517.o mux.o
diff --git a/board/compulab/cm_t3517/cm_t3517.c b/board/compulab/cm_t3517/cm_t3517.c
new file mode 100644
index 0000000..cac1ad9
--- /dev/null
+++ b/board/compulab/cm_t3517/cm_t3517.c
@@ -0,0 +1,231 @@
+/*
+ * (C) Copyright 2014 CompuLab, Ltd. <www.compulab.co.il>
+ *
+ * Authors: Igor Grinberg <grinberg@compulab.co.il>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <status_led.h>
+#include <net.h>
+#include <netdev.h>
+#include <usb.h>
+#include <mmc.h>
+#include <linux/compiler.h>
+#include <linux/usb/musb.h>
+
+#include <asm/io.h>
+#include <asm/arch/mem.h>
+#include <asm/arch/am35x_def.h>
+#include <asm/arch/mmc_host_def.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/arch/musb.h>
+#include <asm/omap_musb.h>
+#include <asm/ehci-omap.h>
+
+#include "../common/common.h"
+#include "../common/eeprom.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+const omap3_sysinfo sysinfo = {
+ DDR_DISCRETE,
+ "CM-T3517 board",
+ "NAND 128/512M",
+};
+
+#ifdef CONFIG_USB_MUSB_AM35X
+static struct musb_hdrc_config cm_t3517_musb_config = {
+ .multipoint = 1,
+ .dyn_fifo = 1,
+ .num_eps = 16,
+ .ram_bits = 12,
+};
+
+static struct omap_musb_board_data cm_t3517_musb_board_data = {
+ .set_phy_power = am35x_musb_phy_power,
+ .clear_irq = am35x_musb_clear_irq,
+ .reset = am35x_musb_reset,
+};
+
+static struct musb_hdrc_platform_data cm_t3517_musb_pdata = {
+#if defined(CONFIG_MUSB_HOST)
+ .mode = MUSB_HOST,
+#elif defined(CONFIG_MUSB_GADGET)
+ .mode = MUSB_PERIPHERAL,
+#else
+#error "Please define either CONFIG_MUSB_HOST or CONFIG_MUSB_GADGET"
+#endif
+ .config = &cm_t3517_musb_config,
+ .power = 250,
+ .platform_ops = &am35x_ops,
+ .board_data = &cm_t3517_musb_board_data,
+};
+
+static void cm_t3517_musb_init(void)
+{
+ /*
+ * Set up USB clock/mode in the DEVCONF2 register.
+ * USB2.0 PHY reference clock is 13 MHz
+ */
+ clrsetbits_le32(&am35x_scm_general_regs->devconf2,
+ CONF2_REFFREQ | CONF2_OTGMODE | CONF2_PHY_GPIOMODE,
+ CONF2_REFFREQ_13MHZ | CONF2_SESENDEN |
+ CONF2_VBDTCTEN | CONF2_DATPOL);
+
+ if (musb_register(&cm_t3517_musb_pdata, &cm_t3517_musb_board_data,
+ (void *)AM35XX_IPSS_USBOTGSS_BASE))
+ printf("Failed initializing AM35x MUSB!\n");
+}
+#else
+static inline void am3517_evm_musb_init(void) {}
+#endif
+
+int board_init(void)
+{
+ gpmc_init(); /* in SRAM or SDRAM, finish GPMC */
+
+ /* boot param addr */
+ gd->bd->bi_boot_params = (OMAP34XX_SDRC_CS0 + 0x100);
+
+#if defined(CONFIG_STATUS_LED) && defined(STATUS_LED_BOOT)
+ status_led_set(STATUS_LED_BOOT, STATUS_LED_ON);
+#endif
+
+ cm_t3517_musb_init();
+
+ return 0;
+}
+
+int misc_init_r(void)
+{
+ cl_print_pcb_info();
+ dieid_num_r();
+
+ return 0;
+}
+
+#if defined(CONFIG_GENERIC_MMC) && !defined(CONFIG_SPL_BUILD)
+#define SB_T35_CD_GPIO 144
+#define SB_T35_WP_GPIO 59
+
+int board_mmc_init(bd_t *bis)
+{
+ return omap_mmc_init(0, 0, 0, SB_T35_CD_GPIO, SB_T35_WP_GPIO);
+}
+#endif
+
+#ifdef CONFIG_DRIVER_TI_EMAC
+#define CONTROL_EFUSE_EMAC_LSB 0x48002380
+#define CONTROL_EFUSE_EMAC_MSB 0x48002384
+
+static int am3517_get_efuse_enetaddr(u8 *enetaddr)
+{
+ u32 lsb = __raw_readl(CONTROL_EFUSE_EMAC_LSB);
+ u32 msb = __raw_readl(CONTROL_EFUSE_EMAC_MSB);
+
+ enetaddr[0] = (u8)((msb >> 16) & 0xff);
+ enetaddr[1] = (u8)((msb >> 8) & 0xff);
+ enetaddr[2] = (u8)(msb & 0xff);
+ enetaddr[3] = (u8)((lsb >> 16) & 0xff);
+ enetaddr[4] = (u8)((lsb >> 8) & 0xff);
+ enetaddr[5] = (u8)(lsb & 0xff);
+
+ return is_valid_ether_addr(enetaddr);
+}
+
+static inline int cm_t3517_init_emac(bd_t *bis)
+{
+ int ret = cpu_eth_init(bis);
+
+ if (ret > 0)
+ return ret;
+
+ printf("Failed initializing EMAC! ");
+ return 0;
+}
+#else /* !CONFIG_DRIVER_TI_EMAC */
+static inline int am3517_get_efuse_enetaddr(u8 *enetaddr) { return 1; }
+static inline int cm_t3517_init_emac(bd_t *bis) { return 0; }
+#endif /* CONFIG_DRIVER_TI_EMAC */
+
+/*
+ * Routine: handle_mac_address
+ * Description: prepare MAC address for on-board Ethernet.
+ */
+static int cm_t3517_handle_mac_address(void)
+{
+ unsigned char enetaddr[6];
+ int ret;
+
+ ret = eth_getenv_enetaddr("ethaddr", enetaddr);
+ if (ret)
+ return 0;
+
+ ret = cl_eeprom_read_mac_addr(enetaddr);
+ if (ret) {
+ ret = am3517_get_efuse_enetaddr(enetaddr);
+ if (ret)
+ return ret;
+ }
+
+ if (!is_valid_ether_addr(enetaddr))
+ return -1;
+
+ return eth_setenv_enetaddr("ethaddr", enetaddr);
+}
+
+#define SB_T35_ETH_RST_GPIO 164
+
+/*
+ * Routine: board_eth_init
+ * Description: initialize module and base-board Ethernet chips
+ */
+int board_eth_init(bd_t *bis)
+{
+ int rc = 0, rc1 = 0;
+
+ rc1 = cm_t3517_handle_mac_address();
+ if (rc1)
+ printf("No MAC address found! ");
+
+ rc1 = cm_t3517_init_emac(bis);
+ if (rc1 > 0)
+ rc++;
+
+ rc1 = cl_omap3_smc911x_init(0, 4, CONFIG_SMC911X_BASE,
+ NULL, SB_T35_ETH_RST_GPIO);
+ if (rc1 > 0)
+ rc++;
+
+ return rc;
+}
+
+#ifdef CONFIG_USB_EHCI_OMAP
+static struct omap_usbhs_board_data cm_t3517_usbhs_bdata = {
+ .port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
+ .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
+ .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
+};
+
+#define CM_T3517_USB_HUB_RESET_GPIO 152
+#define SB_T35_USB_HUB_RESET_GPIO 98
+
+int ehci_hcd_init(int index, enum usb_init_type init,
+ struct ehci_hccr **hccr, struct ehci_hcor **hcor)
+{
+ cl_usb_hub_init(CM_T3517_USB_HUB_RESET_GPIO, "cm-t3517 hub rst");
+ cl_usb_hub_init(SB_T35_USB_HUB_RESET_GPIO, "sb-t35 hub rst");
+
+ return omap_ehci_hcd_init(index, &cm_t3517_usbhs_bdata, hccr, hcor);
+}
+
+int ehci_hcd_stop(void)
+{
+ cl_usb_hub_deinit(CM_T3517_USB_HUB_RESET_GPIO);
+ cl_usb_hub_deinit(SB_T35_USB_HUB_RESET_GPIO);
+
+ return omap_ehci_hcd_stop();
+}
+#endif /* CONFIG_USB_EHCI_OMAP */
diff --git a/board/compulab/cm_t3517/mux.c b/board/compulab/cm_t3517/mux.c
new file mode 100644
index 0000000..88ce2cc
--- /dev/null
+++ b/board/compulab/cm_t3517/mux.c
@@ -0,0 +1,236 @@
+/*
+ * (C) Copyright 2014 CompuLab, Ltd. <www.compulab.co.il>
+ *
+ * Authors: Igor Grinberg <grinberg@compulab.co.il>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/arch/mux.h>
+#include <asm/io.h>
+
+void set_muxconf_regs(void)
+{
+ /* SDRC */
+ MUX_VAL(CP(SDRC_D0), (IEN | PTD | DIS | M0));
+ MUX_VAL(CP(SDRC_D1), (IEN | PTD | DIS | M0));
+ MUX_VAL(CP(SDRC_D2), (IEN | PTD | DIS | M0));
+ MUX_VAL(CP(SDRC_D3), (IEN | PTD | DIS | M0));
+ MUX_VAL(CP(SDRC_D4), (IEN | PTD | DIS | M0));
+ MUX_VAL(CP(SDRC_D5), (IEN | PTD | DIS | M0));
+ MUX_VAL(CP(SDRC_D6), (IEN | PTD | DIS | M0));
+ MUX_VAL(CP(SDRC_D7), (IEN | PTD | DIS | M0));
+ MUX_VAL(CP(SDRC_D8), (IEN | PTD | DIS | M0));
+ MUX_VAL(CP(SDRC_D9), (IEN | PTD | DIS | M0));
+ MUX_VAL(CP(SDRC_D10), (IEN | PTD | DIS | M0));
+ MUX_VAL(CP(SDRC_D11), (IEN | PTD | DIS | M0));
+ MUX_VAL(CP(SDRC_D12), (IEN | PTD | DIS | M0));
+ MUX_VAL(CP(SDRC_D13), (IEN | PTD | DIS | M0));
+ MUX_VAL(CP(SDRC_D14), (IEN | PTD | DIS | M0));
+ MUX_VAL(CP(SDRC_D15), (IEN | PTD | DIS | M0));
+ MUX_VAL(CP(SDRC_D16), (IEN | PTD | DIS | M0));
+ MUX_VAL(CP(SDRC_D17), (IEN | PTD | DIS | M0));
+ MUX_VAL(CP(SDRC_D18), (IEN | PTD | DIS | M0));
+ MUX_VAL(CP(SDRC_D19), (IEN | PTD | DIS | M0));
+ MUX_VAL(CP(SDRC_D20), (IEN | PTD | DIS | M0));
+ MUX_VAL(CP(SDRC_D21), (IEN | PTD | DIS | M0));
+ MUX_VAL(CP(SDRC_D22), (IEN | PTD | DIS | M0));
+ MUX_VAL(CP(SDRC_D23), (IEN | PTD | DIS | M0));
+ MUX_VAL(CP(SDRC_D24), (IEN | PTD | DIS | M0));
+ MUX_VAL(CP(SDRC_D25), (IEN | PTD | DIS | M0));
+ MUX_VAL(CP(SDRC_D26), (IEN | PTD | DIS | M0));
+ MUX_VAL(CP(SDRC_D27), (IEN | PTD | DIS | M0));
+ MUX_VAL(CP(SDRC_D28), (IEN | PTD | DIS | M0));
+ MUX_VAL(CP(SDRC_D29), (IEN | PTD | DIS | M0));
+ MUX_VAL(CP(SDRC_D30), (IEN | PTD | DIS | M0));
+ MUX_VAL(CP(SDRC_D31), (IEN | PTD | DIS | M0));
+ MUX_VAL(CP(SDRC_CLK), (IEN | PTD | DIS | M0));
+ MUX_VAL(CP(SDRC_DQS0), (IEN | PTD | DIS | M0));
+ MUX_VAL(CP(SDRC_DQS1), (IEN | PTD | DIS | M0));
+ MUX_VAL(CP(SDRC_DQS2), (IEN | PTD | DIS | M0));
+ MUX_VAL(CP(SDRC_DQS3), (IEN | PTD | DIS | M0));
+ MUX_VAL(CP(SDRC_CKE0), (IDIS | PTU | EN | M0));
+ MUX_VAL(CP(SDRC_CKE1), (IDIS | PTD | DIS | M7));
+
+ /* GPMC */
+ MUX_VAL(CP(GPMC_A1), (IDIS | PTU | EN | M0));
+ MUX_VAL(CP(GPMC_A2), (IDIS | PTU | EN | M0));
+ MUX_VAL(CP(GPMC_A3), (IDIS | PTU | EN | M0));
+ MUX_VAL(CP(GPMC_A4), (IDIS | PTU | EN | M0));
+ MUX_VAL(CP(GPMC_A5), (IDIS | PTU | EN | M0));
+ MUX_VAL(CP(GPMC_A6), (IDIS | PTU | EN | M0));
+ MUX_VAL(CP(GPMC_A7), (IDIS | PTU | EN | M0));
+ MUX_VAL(CP(GPMC_A8), (IDIS | PTU | EN | M0));
+ MUX_VAL(CP(GPMC_A9), (IDIS | PTU | EN | M0));
+ MUX_VAL(CP(GPMC_A10), (IDIS | PTU | EN | M0));
+ MUX_VAL(CP(GPMC_D0), (IEN | PTU | EN | M0));
+ MUX_VAL(CP(GPMC_D1), (IEN | PTU | EN | M0));
+ MUX_VAL(CP(GPMC_D2), (IEN | PTU | EN | M0));
+ MUX_VAL(CP(GPMC_D3), (IEN | PTU | EN | M0));
+ MUX_VAL(CP(GPMC_D4), (IEN | PTU | EN | M0));
+ MUX_VAL(CP(GPMC_D5), (IEN | PTU | EN | M0));
+ MUX_VAL(CP(GPMC_D6), (IEN | PTU | EN | M0));
+ MUX_VAL(CP(GPMC_D7), (IEN | PTU | EN | M0));
+ MUX_VAL(CP(GPMC_D8), (IEN | PTU | EN | M0));
+ MUX_VAL(CP(GPMC_D9), (IEN | PTU | EN | M0));
+ MUX_VAL(CP(GPMC_D10), (IEN | PTU | EN | M0));
+ MUX_VAL(CP(GPMC_D11), (IEN | PTU | EN | M0));
+ MUX_VAL(CP(GPMC_D12), (IEN | PTU | EN | M0));
+ MUX_VAL(CP(GPMC_D13), (IEN | PTU | EN | M0));
+ MUX_VAL(CP(GPMC_D14), (IEN | PTU | EN | M0));
+ MUX_VAL(CP(GPMC_D15), (IEN | PTU | EN | M0));
+ MUX_VAL(CP(GPMC_NCS0), (IDIS | PTU | EN | M0));
+
+ /* SB-T35 Ethernet */
+ MUX_VAL(CP(GPMC_NCS4), (IEN | PTU | EN | M0));
+ /* DVI enable */
+ MUX_VAL(CP(GPMC_NCS3), (IDIS | PTU | DIS | M4));/*GPIO_54*/
+ /* DataImage backlight */
+ MUX_VAL(CP(GPMC_NCS7), (IDIS | PTU | DIS | M4));/*GPIO_58*/
+
+ /* SB-T35 SD/MMC WP GPIO59 */
+ MUX_VAL(CP(GPMC_CLK), (IEN | PTU | EN | M4)); /*GPIO_59*/
+ MUX_VAL(CP(GPMC_NWE), (IDIS | PTD | DIS | M0));
+ MUX_VAL(CP(GPMC_NOE), (IDIS | PTD | DIS | M0));
+ MUX_VAL(CP(GPMC_NADV_ALE), (IDIS | PTD | DIS | M0));
+ MUX_VAL(CP(GPMC_NBE0_CLE), (IDIS | PTU | EN | M0));
+ /* SB-T35 Audio Enable GPIO61 */
+ MUX_VAL(CP(GPMC_NBE1), (IDIS | PTU | EN | M4)); /*GPIO_61*/
+ MUX_VAL(CP(GPMC_NWP), (IEN | PTD | DIS | M0));
+ MUX_VAL(CP(GPMC_WAIT0), (IEN | PTU | EN | M0));
+ /* SB-T35 Ethernet IRQ GPIO65 */
+ MUX_VAL(CP(GPMC_WAIT3), (IEN | PTU | EN | M4)); /*GPIO_65*/
+
+ /* UART3 Console */
+ MUX_VAL(CP(UART3_RX_IRRX), (IEN | PTD | DIS | M0));
+ MUX_VAL(CP(UART3_TX_IRTX), (IDIS | PTD | DIS | M0));
+ /* RTC V3020 nCS GPIO163 */
+ MUX_VAL(CP(UART3_CTS_RCTX), (IEN | PTU | EN | M4)); /*GPIO_163*/
+ /* SB-T35 Ethernet nRESET GPIO164 */
+ MUX_VAL(CP(UART3_RTS_SD), (IDIS | PTU | EN | M4)); /*GPIO_164*/
+
+ /* SB-T35 SD/MMC CD GPIO144 */
+ MUX_VAL(CP(UART2_CTS), (IEN | PTU | EN | M4)); /*GPIO_144*/
+ /* WIFI nRESET GPIO145 */
+ MUX_VAL(CP(UART2_RTS), (IEN | PTD | EN | M4)); /*GPIO_145*/
+ /* USB1 PHY Reset GPIO 146 */
+ MUX_VAL(CP(UART2_TX), (IEN | PTD | EN | M4)); /*GPIO_146*/
+ /* USB2 PHY Reset GPIO 147 */
+ MUX_VAL(CP(UART2_RX), (IEN | PTD | EN | M4)); /*GPIO_147*/
+
+ /* MMC1 */
+ MUX_VAL(CP(MMC1_CLK), (IDIS | PTU | EN | M0));
+ MUX_VAL(CP(MMC1_CMD), (IEN | PTU | EN | M0));
+ MUX_VAL(CP(MMC1_DAT0), (IEN | PTU | EN | M0));
+ MUX_VAL(CP(MMC1_DAT1), (IEN | PTU | EN | M0));
+ MUX_VAL(CP(MMC1_DAT2), (IEN | PTU | EN | M0));
+ MUX_VAL(CP(MMC1_DAT3), (IEN | PTU | EN | M0));
+
+ /* DSS */
+ MUX_VAL(CP(DSS_PCLK), (IDIS | PTD | DIS | M0));
+ MUX_VAL(CP(DSS_HSYNC), (IDIS | PTD | DIS | M0));
+ MUX_VAL(CP(DSS_VSYNC), (IDIS | PTD | DIS | M0));
+ MUX_VAL(CP(DSS_ACBIAS), (IDIS | PTD | DIS | M0));
+ MUX_VAL(CP(DSS_DATA0), (IDIS | PTD | DIS | M0));
+ MUX_VAL(CP(DSS_DATA1), (IDIS | PTD | DIS | M0));
+ MUX_VAL(CP(DSS_DATA2), (IDIS | PTD | DIS | M0));
+ MUX_VAL(CP(DSS_DATA3), (IDIS | PTD | DIS | M0));
+ MUX_VAL(CP(DSS_DATA4), (IDIS | PTD | DIS | M0));
+ MUX_VAL(CP(DSS_DATA5), (IDIS | PTD | DIS | M0));
+ MUX_VAL(CP(DSS_DATA6), (IDIS | PTD | DIS | M0));
+ MUX_VAL(CP(DSS_DATA7), (IDIS | PTD | DIS | M0));
+ MUX_VAL(CP(DSS_DATA8), (IDIS | PTD | DIS | M0));
+ MUX_VAL(CP(DSS_DATA9), (IDIS | PTD | DIS | M0));
+ MUX_VAL(CP(DSS_DATA10), (IDIS | PTD | DIS | M0));
+ MUX_VAL(CP(DSS_DATA11), (IDIS | PTD | DIS | M0));
+ MUX_VAL(CP(DSS_DATA12), (IDIS | PTD | DIS | M0));
+ MUX_VAL(CP(DSS_DATA13), (IDIS | PTD | DIS | M0));
+ MUX_VAL(CP(DSS_DATA14), (IDIS | PTD | DIS | M0));
+ MUX_VAL(CP(DSS_DATA15), (IDIS | PTD | DIS | M0));
+ MUX_VAL(CP(DSS_DATA16), (IDIS | PTD | DIS | M0));
+ MUX_VAL(CP(DSS_DATA17), (IDIS | PTD | DIS | M0));
+ MUX_VAL(CP(DSS_DATA18), (IDIS | PTD | DIS | M0));
+ MUX_VAL(CP(DSS_DATA19), (IDIS | PTD | DIS | M0));
+ MUX_VAL(CP(DSS_DATA20), (IDIS | PTD | DIS | M0));
+ MUX_VAL(CP(DSS_DATA21), (IDIS | PTD | DIS | M0));
+ MUX_VAL(CP(DSS_DATA22), (IDIS | PTD | DIS | M0));
+ MUX_VAL(CP(DSS_DATA23), (IDIS | PTD | DIS | M0));
+
+ /* I2C */
+ MUX_VAL(CP(I2C1_SCL), (IEN | PTU | EN | M0));
+ MUX_VAL(CP(I2C1_SDA), (IEN | PTU | EN | M0));
+ MUX_VAL(CP(I2C3_SCL), (IEN | PTU | EN | M0));
+ MUX_VAL(CP(I2C3_SDA), (IEN | PTU | EN | M0));
+
+ /* SB-T35 USB HUB Reset GPIO98 */
+ MUX_VAL(CP(CCDC_WEN), (IDIS | PTU | EN | M4)); /*GPIO_98*/
+ /* CM-T3517 USB HUB Reset GPIO152 */
+ MUX_VAL(CP(MCBSP4_CLKX), (IDIS | PTD | DIS | M4)); /*GPIO_152*/
+
+ /* RMII */
+ MUX_VAL(CP(RMII_MDIO_DATA), (IEN | PTU | EN | M0));
+ MUX_VAL(CP(RMII_MDIO_CLK), (M0));
+ MUX_VAL(CP(RMII_RXD0), (IEN | PTD | DIS | M0));
+ MUX_VAL(CP(RMII_RXD1), (IEN | PTD | DIS | M0));
+ MUX_VAL(CP(RMII_CRS_DV), (IEN | PTD | DIS | M0));
+ MUX_VAL(CP(RMII_RXER), (IEN | PTD | DIS | M0));
+ MUX_VAL(CP(RMII_TXD0), (IDIS | M0));
+ MUX_VAL(CP(RMII_TXD1), (IDIS | M0));
+ MUX_VAL(CP(RMII_TXEN), (IDIS | M0));
+ MUX_VAL(CP(RMII_50MHZ_CLK), (IEN | PTU | DIS | M0));
+
+ /* Green LED GPIO186 */
+ MUX_VAL(CP(SYS_CLKOUT2), (IDIS | PTU | DIS | M4)); /*GPIO_186*/
+
+ /* SPI */
+ MUX_VAL(CP(MCBSP1_CLKR), (IEN | PTD | DIS | M1)); /*MCSPI4_CLK*/
+ MUX_VAL(CP(MCBSP1_DX), (IEN | PTD | DIS | M1)); /*MCSPI4_SIMO*/
+ MUX_VAL(CP(MCBSP1_DR), (IEN | PTD | DIS | M1)); /*MCSPI4_SOMI*/
+ MUX_VAL(CP(MCBSP1_FSX), (IEN | PTU | EN | M1)); /*MCSPI4_CS0*/
+ /* LCD reset GPIO157 */
+ MUX_VAL(CP(MCBSP1_FSR), (IDIS | PTU | DIS | M4)); /*GPIO_157*/
+
+ /* RTC V3020 CS Enable GPIO160 */
+ MUX_VAL(CP(MCBSP_CLKS), (IEN | PTD | EN | M4)); /*GPIO_160*/
+ /* SB-T35 LVDS Transmitter SHDN GPIO162 */
+ MUX_VAL(CP(MCBSP1_CLKX), (IEN | PTU | DIS | M4)); /*GPIO_162*/
+
+ /* USB0 - mUSB */
+ MUX_VAL(CP(USB0_DRVBUS), (IEN | PTD | EN | M0));
+ /* USB1 EHCI */
+ MUX_VAL(CP(ETK_D0_ES2), (IEN | PTD | EN | M3)); /*HSUSB1_DT0*/
+ MUX_VAL(CP(ETK_D1_ES2), (IEN | PTD | EN | M3)); /*HSUSB1_DT1*/
+ MUX_VAL(CP(ETK_D2_ES2), (IEN | PTD | EN | M3)); /*HSUSB1_DT2*/
+ MUX_VAL(CP(ETK_D7_ES2), (IEN | PTD | EN | M3)); /*HSUSB1_DT3*/
+ MUX_VAL(CP(ETK_D4_ES2), (IEN | PTD | EN | M3)); /*HSUSB1_DT4*/
+ MUX_VAL(CP(ETK_D5_ES2), (IEN | PTD | EN | M3)); /*HSUSB1_DT5*/
+ MUX_VAL(CP(ETK_D6_ES2), (IEN | PTD | EN | M3)); /*HSUSB1_DT6*/
+ MUX_VAL(CP(ETK_D3_ES2), (IEN | PTD | EN | M3)); /*HSUSB1_DT7*/
+ MUX_VAL(CP(ETK_D8_ES2), (IEN | PTD | EN | M3)); /*HSUSB1_DIR*/
+ MUX_VAL(CP(ETK_D9_ES2), (IEN | PTD | EN | M3)); /*HSUSB1_NXT*/
+ MUX_VAL(CP(ETK_CTL_ES2), (IDIS | PTD | DIS | M3)); /*HSUSB1_CLK*/
+ MUX_VAL(CP(ETK_CLK_ES2), (IDIS | PTU | DIS | M3)); /*HSUSB1_STP*/
+ /* USB2 EHCI */
+ MUX_VAL(CP(ETK_D14_ES2), (IEN | PTD | EN | M3)); /*HSUSB2_DT0*/
+ MUX_VAL(CP(ETK_D15_ES2), (IEN | PTD | EN | M3)); /*HSUSB2_DT1*/
+ MUX_VAL(CP(MCSPI1_CS3), (IEN | PTD | EN | M3)); /*HSUSB2_DT2*/
+ MUX_VAL(CP(MCSPI2_CS1), (IEN | PTD | EN | M3)); /*HSUSB2_DT3*/
+ MUX_VAL(CP(MCSPI2_SIMO), (IEN | PTD | EN | M3)); /*HSUSB2_DT4*/
+ MUX_VAL(CP(MCSPI2_SOMI), (IEN | PTD | EN | M3)); /*HSUSB2_DT5*/
+ MUX_VAL(CP(MCSPI2_CS0), (IEN | PTD | EN | M3)); /*HSUSB2_DT6*/
+ MUX_VAL(CP(MCSPI2_CLK), (IEN | PTD | EN | M3)); /*HSUSB2_DT7*/
+ MUX_VAL(CP(ETK_D12_ES2), (IEN | PTD | EN | M3)); /*HSUSB2_DIR*/
+ MUX_VAL(CP(ETK_D13_ES2), (IEN | PTD | EN | M3)); /*HSUSB2_NXT*/
+ MUX_VAL(CP(ETK_D10_ES2), (IDIS | PTD | DIS | M3)); /*HSUSB2_CLK*/
+ MUX_VAL(CP(ETK_D11_ES2), (IDIS | PTU | DIS | M3)); /*HSUSB2_STP*/
+
+ /* SYS_BOOT */
+ MUX_VAL(CP(SYS_BOOT0), (IEN | PTU | DIS | M4)); /*GPIO_2*/
+ MUX_VAL(CP(SYS_BOOT1), (IEN | PTU | DIS | M4)); /*GPIO_3*/
+ MUX_VAL(CP(SYS_BOOT2), (IEN | PTU | DIS | M4)); /*GPIO_4*/
+ MUX_VAL(CP(SYS_BOOT3), (IEN | PTU | DIS | M4)); /*GPIO_5*/
+ MUX_VAL(CP(SYS_BOOT4), (IEN | PTU | DIS | M4)); /*GPIO_6*/
+ MUX_VAL(CP(SYS_BOOT5), (IEN | PTU | DIS | M4)); /*GPIO_7*/
+}
diff --git a/board/compulab/cm_t54/cm_t54.c b/board/compulab/cm_t54/cm_t54.c
index 944b723..b1a067d 100644
--- a/board/compulab/cm_t54/cm_t54.c
+++ b/board/compulab/cm_t54/cm_t54.c
@@ -100,16 +100,11 @@
#define SB_T54_CD_GPIO 228
#define SB_T54_WP_GPIO 229
-int board_mmc_getcd(struct mmc *mmc)
-{
- return !gpio_get_value(SB_T54_CD_GPIO);
-}
-
int board_mmc_init(bd_t *bis)
{
int ret0, ret1;
- ret0 = omap_mmc_init(0, 0, 0, -1, SB_T54_WP_GPIO);
+ ret0 = omap_mmc_init(0, 0, 0, SB_T54_CD_GPIO, SB_T54_WP_GPIO);
if (ret0)
printf("cm_t54: failed to initialize mmc0\n");
diff --git a/board/compulab/common/Makefile b/board/compulab/common/Makefile
index 4044ac9..dbf0009 100644
--- a/board/compulab/common/Makefile
+++ b/board/compulab/common/Makefile
@@ -6,5 +6,8 @@
# SPDX-License-Identifier: GPL-2.0+
#
-obj-$(CONFIG_SYS_I2C) += eeprom.o
-obj-$(CONFIG_LCD) += omap3_display.o
+obj-y += common.o
+obj-$(CONFIG_SYS_I2C) += eeprom.o
+obj-$(CONFIG_LCD) += omap3_display.o
+obj-$(CONFIG_SPLASH_SCREEN) += splash.o
+obj-$(CONFIG_SMC911X) += omap3_smc911x.o
diff --git a/board/compulab/common/common.c b/board/compulab/common/common.c
new file mode 100644
index 0000000..b25d9a2
--- /dev/null
+++ b/board/compulab/common/common.c
@@ -0,0 +1,59 @@
+/*
+ * (C) Copyright 2014 CompuLab, Ltd. <www.compulab.co.il>
+ *
+ * Authors: Igor Grinberg <grinberg@compulab.co.il>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/bootm.h>
+#include <asm/gpio.h>
+
+#include "common.h"
+#include "eeprom.h"
+
+void cl_print_pcb_info(void)
+{
+ u32 board_rev = get_board_rev();
+ u32 rev_major = board_rev / 100;
+ u32 rev_minor = board_rev - (rev_major * 100);
+
+ if ((rev_minor / 10) * 10 == rev_minor)
+ rev_minor = rev_minor / 10;
+
+ printf("PCB: %u.%u\n", rev_major, rev_minor);
+}
+
+#ifdef CONFIG_SERIAL_TAG
+void __weak get_board_serial(struct tag_serialnr *serialnr)
+{
+ /*
+ * This corresponds to what happens when we can communicate with the
+ * eeprom but don't get a valid board serial value.
+ */
+ serialnr->low = 0;
+ serialnr->high = 0;
+};
+#endif
+
+#ifdef CONFIG_CMD_USB
+int cl_usb_hub_init(int gpio, const char *label)
+{
+ if (gpio_request(gpio, label)) {
+ printf("Error: can't obtain GPIO%d for %s", gpio, label);
+ return -1;
+ }
+
+ gpio_direction_output(gpio, 0);
+ udelay(10);
+ gpio_set_value(gpio, 1);
+ udelay(1000);
+ return 0;
+}
+
+void cl_usb_hub_deinit(int gpio)
+{
+ gpio_free(gpio);
+}
+#endif
diff --git a/board/compulab/common/common.h b/board/compulab/common/common.h
new file mode 100644
index 0000000..68ffb11
--- /dev/null
+++ b/board/compulab/common/common.h
@@ -0,0 +1,47 @@
+/*
+ * (C) Copyright 2014 CompuLab, Ltd. <www.compulab.co.il>
+ *
+ * Authors: Igor Grinberg <grinberg@compulab.co.il>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef _CL_COMMON_
+#define _CL_COMMON_
+
+#include <asm/errno.h>
+
+void cl_print_pcb_info(void);
+
+#ifdef CONFIG_CMD_USB
+int cl_usb_hub_init(int gpio, const char *label);
+void cl_usb_hub_deinit(int gpio);
+#else /* !CONFIG_CMD_USB */
+static inline int cl_usb_hub_init(int gpio, const char *label)
+{
+ return -ENOSYS;
+}
+static inline void cl_usb_hub_deinit(int gpio) {}
+#endif /* CONFIG_CMD_USB */
+
+#ifdef CONFIG_SPLASH_SCREEN
+int cl_splash_screen_prepare(int nand_offset);
+#else /* !CONFIG_SPLASH_SCREEN */
+static inline int cl_splash_screen_prepare(int nand_offset)
+{
+ return -ENOSYS;
+}
+#endif /* CONFIG_SPLASH_SCREEN */
+
+#ifdef CONFIG_SMC911X
+int cl_omap3_smc911x_init(int id, int cs, u32 base_addr,
+ int (*reset)(int), int rst_gpio);
+#else /* !CONFIG_SMC911X */
+static inline int cl_omap3_smc911x_init(int id, int cs, u32 base_addr,
+ int (*reset)(int), int rst_gpio)
+{
+ return -ENOSYS;
+}
+#endif /* CONFIG_SMC911X */
+
+#endif /* _CL_COMMON_ */
diff --git a/board/compulab/common/eeprom.c b/board/compulab/common/eeprom.c
index 2df3ada..a45e7be 100644
--- a/board/compulab/common/eeprom.c
+++ b/board/compulab/common/eeprom.c
@@ -109,23 +109,27 @@
return cl_eeprom_read(offset, buf, 6);
}
+static u32 board_rev;
+
/*
* Routine: cl_eeprom_get_board_rev
* Description: read system revision from eeprom
*/
u32 cl_eeprom_get_board_rev(void)
{
- u32 rev = 0;
char str[5]; /* Legacy representation can contain at most 4 digits */
uint offset = BOARD_REV_OFFSET_LEGACY;
+ if (board_rev)
+ return board_rev;
+
if (cl_eeprom_setup_layout())
return 0;
if (cl_eeprom_layout != LAYOUT_LEGACY)
offset = BOARD_REV_OFFSET;
- if (cl_eeprom_read(offset, (uchar *)&rev, BOARD_REV_SIZE))
+ if (cl_eeprom_read(offset, (uchar *)&board_rev, BOARD_REV_SIZE))
return 0;
/*
@@ -133,9 +137,9 @@
* representation. i.e. for rev 1.00: 0x100 --> 0x64
*/
if (cl_eeprom_layout == LAYOUT_LEGACY) {
- sprintf(str, "%x", rev);
- rev = simple_strtoul(str, NULL, 10);
+ sprintf(str, "%x", board_rev);
+ board_rev = simple_strtoul(str, NULL, 10);
}
- return rev;
+ return board_rev;
};
diff --git a/board/compulab/common/omap3_smc911x.c b/board/compulab/common/omap3_smc911x.c
new file mode 100644
index 0000000..4561661
--- /dev/null
+++ b/board/compulab/common/omap3_smc911x.c
@@ -0,0 +1,93 @@
+/*
+ * (C) Copyright 2014 CompuLab, Ltd. <www.compulab.co.il>
+ *
+ * Authors: Igor Grinberg <grinberg@compulab.co.il>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <netdev.h>
+
+#include <asm/io.h>
+#include <asm/errno.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/mem.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/gpio.h>
+
+#include "common.h"
+
+static u32 cl_omap3_smc911x_gpmc_net_config[GPMC_MAX_REG] = {
+ NET_GPMC_CONFIG1,
+ NET_GPMC_CONFIG2,
+ NET_GPMC_CONFIG3,
+ NET_GPMC_CONFIG4,
+ NET_GPMC_CONFIG5,
+ NET_GPMC_CONFIG6,
+ 0
+};
+
+static void cl_omap3_smc911x_setup_net_chip_gmpc(int cs, u32 base_addr)
+{
+ struct ctrl *ctrl_base = (struct ctrl *)OMAP34XX_CTRL_BASE;
+
+ enable_gpmc_cs_config(cl_omap3_smc911x_gpmc_net_config,
+ &gpmc_cfg->cs[cs], base_addr, GPMC_SIZE_16M);
+
+ /* Enable off mode for NWE in PADCONF_GPMC_NWE register */
+ writew(readw(&ctrl_base->gpmc_nwe) | 0x0E00, &ctrl_base->gpmc_nwe);
+
+ /* Enable off mode for NOE in PADCONF_GPMC_NADV_ALE register */
+ writew(readw(&ctrl_base->gpmc_noe) | 0x0E00, &ctrl_base->gpmc_noe);
+
+ /* Enable off mode for ALE in PADCONF_GPMC_NADV_ALE register */
+ writew(readw(&ctrl_base->gpmc_nadv_ale) | 0x0E00,
+ &ctrl_base->gpmc_nadv_ale);
+}
+
+#ifdef CONFIG_OMAP_GPIO
+static int cl_omap3_smc911x_reset_net_chip(int gpio)
+{
+ int err;
+
+ if (!gpio_is_valid(gpio))
+ return -EINVAL;
+
+ err = gpio_request(gpio, "eth rst");
+ if (err)
+ return err;
+
+ /* Set gpio as output and send a pulse */
+ gpio_direction_output(gpio, 1);
+ udelay(1);
+ gpio_set_value(gpio, 0);
+ mdelay(40);
+ gpio_set_value(gpio, 1);
+ mdelay(1);
+
+ return 0;
+}
+#else /* !CONFIG_OMAP_GPIO */
+static inline int cl_omap3_smc911x_reset_net_chip(int gpio) { return 0; }
+#endif /* CONFIG_OMAP_GPIO */
+
+int cl_omap3_smc911x_init(int id, int cs, u32 base_addr,
+ int (*reset)(int), int rst_gpio)
+{
+ int ret;
+
+ cl_omap3_smc911x_setup_net_chip_gmpc(cs, base_addr);
+
+ if (reset)
+ reset(rst_gpio);
+ else
+ cl_omap3_smc911x_reset_net_chip(rst_gpio);
+
+ ret = smc911x_initialize(id, base_addr);
+ if (ret > 0)
+ return ret;
+
+ printf("Failed initializing SMC911x! ");
+ return 0;
+}
diff --git a/board/compulab/common/splash.c b/board/compulab/common/splash.c
new file mode 100644
index 0000000..49ed49b
--- /dev/null
+++ b/board/compulab/common/splash.c
@@ -0,0 +1,72 @@
+/*
+ * (C) Copyright 2014 CompuLab, Ltd. <www.compulab.co.il>
+ *
+ * Authors: Igor Grinberg <grinberg@compulab.co.il>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <nand.h>
+#include <bmp_layout.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#ifdef CONFIG_CMD_NAND
+static int splash_load_from_nand(u32 bmp_load_addr, int nand_offset)
+{
+ struct bmp_header *bmp_hdr;
+ int res;
+ size_t bmp_size, bmp_header_size = sizeof(struct bmp_header);
+
+ if (bmp_load_addr + bmp_header_size >= gd->start_addr_sp)
+ goto splash_address_too_high;
+
+ res = nand_read_skip_bad(&nand_info[nand_curr_device],
+ nand_offset, &bmp_header_size,
+ NULL, nand_info[nand_curr_device].size,
+ (u_char *)bmp_load_addr);
+ if (res < 0)
+ return res;
+
+ bmp_hdr = (struct bmp_header *)bmp_load_addr;
+ bmp_size = le32_to_cpu(bmp_hdr->file_size);
+
+ if (bmp_load_addr + bmp_size >= gd->start_addr_sp)
+ goto splash_address_too_high;
+
+ return nand_read_skip_bad(&nand_info[nand_curr_device],
+ nand_offset, &bmp_size,
+ NULL, nand_info[nand_curr_device].size,
+ (u_char *)bmp_load_addr);
+
+splash_address_too_high:
+ printf("Error: splashimage address too high. Data overwrites U-Boot "
+ "and/or placed beyond DRAM boundaries.\n");
+
+ return -1;
+}
+#else
+static inline int splash_load_from_nand(u32 bmp_load_addr, int nand_offset)
+{
+ return -1;
+}
+#endif /* CONFIG_CMD_NAND */
+
+int cl_splash_screen_prepare(int nand_offset)
+{
+ char *env_splashimage_value;
+ u32 bmp_load_addr;
+
+ env_splashimage_value = getenv("splashimage");
+ if (env_splashimage_value == NULL)
+ return -1;
+
+ bmp_load_addr = simple_strtoul(env_splashimage_value, 0, 16);
+ if (bmp_load_addr == 0) {
+ printf("Error: bad splashimage address specified\n");
+ return -1;
+ }
+
+ return splash_load_from_nand(bmp_load_addr, nand_offset);
+}
diff --git a/board/siemens/pxm2/board.c b/board/siemens/pxm2/board.c
index 64e69dc..559af0e 100644
--- a/board/siemens/pxm2/board.c
+++ b/board/siemens/pxm2/board.c
@@ -229,7 +229,7 @@
#endif /* #ifdef CONFIG_FACTORYSET */
/* Set rgmii mode and enable rmii clock to be sourced from chip */
- writel(RGMII_MODE_ENABLE , &cdev->miisel);
+ writel(RGMII_MODE_ENABLE | RGMII_INT_DELAY, &cdev->miisel);
rv = cpsw_register(&cpsw_data);
if (rv < 0)
diff --git a/board/ti/am335x/Kconfig b/board/ti/am335x/Kconfig
index b9f6bd7..1ddbb2c 100644
--- a/board/ti/am335x/Kconfig
+++ b/board/ti/am335x/Kconfig
@@ -22,4 +22,19 @@
board you may want something other than UART0 as for example the IDK
uses UART3 so enter 4 here.
+config NOR
+ bool "Support for NOR flash"
+ help
+ The AM335x SoC supports having a NOR flash connected to the GPMC.
+ In practice this is seen as a NOR flash module connected to the
+ "memory cape" for the BeagleBone family.
+
+config NOR_BOOT
+ bool "Support for booting from NOR flash"
+ depends on NOR
+ help
+ Enabling this will make a U-Boot binary that is capable of being
+ booted via NOR. In this case we will enable certain pinmux early
+ as the ROM only partially sets up pinmux. We also default to using
+ NOR for environment.
endif
diff --git a/board/ti/ks2_evm/README b/board/ti/ks2_evm/README
index a551e28..9ee90a4 100644
--- a/board/ti/ks2_evm/README
+++ b/board/ti/ks2_evm/README
@@ -3,10 +3,11 @@
Author: Murali Karicheri <m-karicheri2@ti.com>
-This README has information on the u-boot port for K2HK, K2E boards.
+This README has information on the u-boot port for K2HK, K2E, and K2L EVM boards.
Documentation for this board can be found at
http://www.advantech.com/Support/TI-EVM/EVMK2HX_sd.aspx
https://www.einfochips.com/index.php/partnerships/texas-instruments/k2e-evm.html
+https://www.einfochips.com/index.php/partnerships/texas-instruments/k2l-evm.html
The K2HK board is based on Texas Instruments Keystone2 family of SoCs: K2H, K2K.
More details on these SoCs are available at company websites
@@ -14,7 +15,10 @@
K2H: http://www.ti.com/product/tci6638k2h
The K2E SoC details are available at
- K2E http://www.ti.com/lit/ds/symlink/66ak2e05.pdf
+ http://www.ti.com/lit/ds/symlink/66ak2e05.pdf
+
+The K2L SoC details are available at
+ http://www.ti.com/lit/ds/symlink/tci6630k2l.pdf
Board configuration:
====================
@@ -25,6 +29,7 @@
+------+-------+-------+-----------+-----------+-------+-------+----+
|K2HK |2 |512MB |6MB |4(2) |2 |3 |3 |
|K2E |4 |512MB |2MB |8(2) |2 |3 |3 |
+|K2L |2 |512MB |2MB |4(2) |4 |3 |3 |
+------+-------+-------+-----------+-----------+-------+-------+----+
There are only 2 eth port installed on the boards.
@@ -41,10 +46,13 @@
Board configuration files:
include/configs/k2hk_evm.h
include/configs/k2e_evm.h
+include/configs/k2l_evm.h
+include/configs/k2l_evm.h
As u-boot is migrating to Kconfig there is also board defconfig files
configs/k2e_evm_defconfig
configs/k2hk_evm_defconfig
+configs/k2l_evm_defconfig
Supported boot modes:
- SPI NOR boot
@@ -58,7 +66,7 @@
Build instructions:
===================
-Examples for k2hk, for k2e just replace k2hk prefix accordingly.
+Examples for k2hk, for k2e and k2l just replace k2hk prefix accordingly.
Don't forget to add ARCH=arm and CROSS_COMPILE.
To build u-boot.bin
@@ -84,6 +92,8 @@
on EVM. Follow instructions at
K2HK http://processors.wiki.ti.com/index.php/EVMK2H_Hardware_Setup
K2E http://processors.wiki.ti.com/index.php/EVMK2E_Hardware_Setup
+K2L http://processors.wiki.ti.com/index.php/TCIEVMK2L_Hardware_Setup
+
to configure SW1 dip switch to use "No Boot/JTAG DSP Little Endian Boot Mode"
and Power ON the EVM. Follow instructions to connect serial port of EVM to
PC and start TeraTerm or Hyper Terminal.
@@ -128,8 +138,8 @@
2. Suspend Target. Select Run -> Suspend from top level menu
CortexA15_1 (Free Running)"
3. Load u-boot-spi.gph binary from build folder on to DDR address 0x87000000
- through CCS as described in step 2 of "Load and Run U-Boot on K2HK/K2E EVM
- using CCS", but using address 0x87000000.
+ through CCS as described in step 2 of "Load and Run U-Boot on K2HK/K2E/K2L
+ EVM using CCS", but using address 0x87000000.
4. Free Run the target as described earlier (step 4) to get u-boot prompt
5. At the U-Boot console type following to setup u-boot environment variables.
setenv addr_uboot 0x87000000
diff --git a/board/ti/ks2_evm/board.c b/board/ti/ks2_evm/board.c
index 4029493..ff7bc4b 100644
--- a/board/ti/ks2_evm/board.c
+++ b/board/ti/ks2_evm/board.c
@@ -122,7 +122,6 @@
int nbanks;
u64 size[2];
u64 start[2];
- char name[32];
int nodeoffset;
u32 ddr3a_size;
int unitrd_fixup = 0;
@@ -158,15 +157,13 @@
}
/* reserve memory at start of bank */
- sprintf(name, "mem_reserve_head");
- env = getenv(name);
+ env = getenv("mem_reserve_head");
if (env) {
start[0] += ustrtoul(env, &endp, 0);
size[0] -= ustrtoul(env, &endp, 0);
}
- sprintf(name, "mem_reserve");
- env = getenv(name);
+ env = getenv("mem_reserve");
if (env)
size[0] -= ustrtoul(env, &endp, 0);
diff --git a/board/ti/ks2_evm/board_k2l.c b/board/ti/ks2_evm/board_k2l.c
index 559d20c..729a193 100644
--- a/board/ti/ks2_evm/board_k2l.c
+++ b/board/ti/ks2_evm/board_k2l.c
@@ -10,7 +10,7 @@
#include <common.h>
#include <asm/arch/ddr3.h>
#include <asm/arch/hardware.h>
-#include <asm/ti-common/ti-aemif.h>
+#include <asm/ti-common/keystone_net.h>
DECLARE_GLOBAL_DATA_PTR;
@@ -42,6 +42,44 @@
static struct pll_init_data pa_pll_config =
PASS_PLL_983;
+#ifdef CONFIG_DRIVER_TI_KEYSTONE_NET
+struct eth_priv_t eth_priv_cfg[] = {
+ {
+ .int_name = "K2L_EMAC",
+ .rx_flow = 0,
+ .phy_addr = 0,
+ .slave_port = 1,
+ .sgmii_link_type = SGMII_LINK_MAC_PHY,
+ },
+ {
+ .int_name = "K2L_EMAC1",
+ .rx_flow = 8,
+ .phy_addr = 1,
+ .slave_port = 2,
+ .sgmii_link_type = SGMII_LINK_MAC_PHY,
+ },
+ {
+ .int_name = "K2L_EMAC2",
+ .rx_flow = 16,
+ .phy_addr = 2,
+ .slave_port = 3,
+ .sgmii_link_type = SGMII_LINK_MAC_MAC_FORCED,
+ },
+ {
+ .int_name = "K2L_EMAC3",
+ .rx_flow = 32,
+ .phy_addr = 3,
+ .slave_port = 4,
+ .sgmii_link_type = SGMII_LINK_MAC_MAC_FORCED,
+ },
+};
+
+int get_num_eth_ports(void)
+{
+ return sizeof(eth_priv_cfg) / sizeof(struct eth_priv_t);
+}
+#endif
+
#ifdef CONFIG_BOARD_EARLY_INIT_F
int board_early_init_f(void)
{
diff --git a/configs/am335x_evm_nor_defconfig b/configs/am335x_evm_nor_defconfig
index 41f31cc..be90163 100644
--- a/configs/am335x_evm_nor_defconfig
+++ b/configs/am335x_evm_nor_defconfig
@@ -1,5 +1,6 @@
CONFIG_SPL=y
-CONFIG_SYS_EXTRA_OPTIONS="NAND,NOR"
+CONFIG_SYS_EXTRA_OPTIONS="NAND"
CONFIG_CONS_INDEX=1
+S:CONFIG_ARM=y
+S:CONFIG_TARGET_AM335X_EVM=y
+CONFIG_NOR=y
diff --git a/configs/am335x_evm_norboot_defconfig b/configs/am335x_evm_norboot_defconfig
index 7dbfa27..47ff6cd 100644
--- a/configs/am335x_evm_norboot_defconfig
+++ b/configs/am335x_evm_norboot_defconfig
@@ -1,4 +1,5 @@
-CONFIG_SYS_EXTRA_OPTIONS="NOR,NOR_BOOT"
CONFIG_CONS_INDEX=1
CONFIG_ARM=y
CONFIG_TARGET_AM335X_EVM=y
+CONFIG_NOR=y
+CONFIG_NOR_BOOT=y
diff --git a/configs/cm_t3517_defconfig b/configs/cm_t3517_defconfig
new file mode 100644
index 0000000..4000d2c
--- /dev/null
+++ b/configs/cm_t3517_defconfig
@@ -0,0 +1,4 @@
+CONFIG_SPL=n
++S:CONFIG_ARM=y
++S:CONFIG_OMAP34XX=y
++S:CONFIG_TARGET_CM_T3517=y
diff --git a/drivers/dma/keystone_nav.c b/drivers/dma/keystone_nav.c
index 77707c2..dfca75a 100644
--- a/drivers/dma/keystone_nav.c
+++ b/drivers/dma/keystone_nav.c
@@ -81,9 +81,6 @@
{
u32 j;
- if (qm_cfg == NULL)
- return;
-
queue_close(qm_cfg->qpool_num);
qm_cfg->mngr_cfg->link_ram_base0 = 0;
@@ -105,9 +102,6 @@
{
u32 regd;
- if (!qm_cfg)
- return;
-
cpu_to_bus((u32 *)hd, sizeof(struct qm_host_desc)/4);
regd = (u32)hd | ((sizeof(struct qm_host_desc) >> 4) - 1);
writel(regd, &qm_cfg->queue[qnum].ptr_size_thresh);
@@ -127,9 +121,6 @@
{
u32 uhd;
- if (!qm_cfg)
- return NULL;
-
uhd = readl(&qm_cfg->queue[qnum].ptr_size_thresh) & ~0xf;
if (uhd)
cpu_to_bus((u32 *)uhd, sizeof(struct qm_host_desc)/4);
@@ -139,9 +130,6 @@
struct qm_host_desc *qm_pop_from_free_pool(void)
{
- if (!qm_cfg)
- return NULL;
-
return qm_pop(qm_cfg->qpool_num);
}
diff --git a/drivers/mmc/omap_hsmmc.c b/drivers/mmc/omap_hsmmc.c
index ef2cbf9..ffb5284 100644
--- a/drivers/mmc/omap_hsmmc.c
+++ b/drivers/mmc/omap_hsmmc.c
@@ -611,7 +611,8 @@
if (cd_gpio < 0)
return 1;
- return gpio_get_value(cd_gpio);
+ /* NOTE: assumes card detect signal is active-low */
+ return !gpio_get_value(cd_gpio);
}
static int omap_hsmmc_getwp(struct mmc *mmc)
@@ -624,6 +625,7 @@
if (wp_gpio < 0)
return 0;
+ /* NOTE: assumes write protect signal is active-high */
return gpio_get_value(wp_gpio);
}
#endif
diff --git a/drivers/net/keystone_net.c b/drivers/net/keystone_net.c
index c8681d0..bedab1d 100644
--- a/drivers/net/keystone_net.c
+++ b/drivers/net/keystone_net.c
@@ -315,7 +315,7 @@
writel(cfg->max_rx_len, DEVICE_EMACSL_BASE(port) + CPGMACSL_REG_MAXLEN);
writel(cfg->ctl, DEVICE_EMACSL_BASE(port) + CPGMACSL_REG_CTL);
-#ifdef CONFIG_K2E_EVM
+#if defined(CONFIG_SOC_K2E) || defined(CONFIG_SOC_K2L)
/* Map RX packet flow priority to 0 */
writel(0, DEVICE_EMACSL_BASE(port) + CPGMACSL_REG_RX_PRI_MAP);
#endif
@@ -400,6 +400,9 @@
keystone2_net_serdes_setup();
+ if (sys_has_mdio)
+ keystone2_mdio_reset(mdio_bus);
+
keystone_sgmii_config(phy_dev, eth_priv->slave_port - 1,
eth_priv->sgmii_link_type);
@@ -582,7 +585,7 @@
&ks2_serdes_sgmii_156p25mhz,
CONFIG_KSNET_SERDES_LANES_PER_SGMII);
-#ifdef CONFIG_SOC_K2E
+#if defined(CONFIG_SOC_K2E) || defined(CONFIG_SOC_K2L)
ks2_serdes_init(CONFIG_KSNET_SERDES_SGMII2_BASE,
&ks2_serdes_sgmii_156p25mhz,
CONFIG_KSNET_SERDES_LANES_PER_SGMII);
diff --git a/drivers/net/phy/marvell.c b/drivers/net/phy/marvell.c
index d2ecadc..9437c3b 100644
--- a/drivers/net/phy/marvell.c
+++ b/drivers/net/phy/marvell.c
@@ -276,6 +276,57 @@
return 0;
}
+/**
+ * m88e1518_phy_writebits - write bits to a register
+ */
+void m88e1518_phy_writebits(struct phy_device *phydev,
+ u8 reg_num, u16 offset, u16 len, u16 data)
+{
+ u16 reg, mask;
+
+ if ((len + offset) >= 16)
+ mask = 0 - (1 << offset);
+ else
+ mask = (1 << (len + offset)) - (1 << offset);
+
+ reg = phy_read(phydev, MDIO_DEVAD_NONE, reg_num);
+
+ reg &= ~mask;
+ reg |= data << offset;
+
+ phy_write(phydev, MDIO_DEVAD_NONE, reg_num, reg);
+}
+
+static int m88e1518_config(struct phy_device *phydev)
+{
+ /*
+ * As per Marvell Release Notes - Alaska 88E1510/88E1518/88E1512
+ * /88E1514 Rev A0, Errata Section 3.1
+ */
+ if (phydev->interface == PHY_INTERFACE_MODE_SGMII) {
+ phy_write(phydev, MDIO_DEVAD_NONE, 22, 0x00ff); /* page 0xff */
+ phy_write(phydev, MDIO_DEVAD_NONE, 17, 0x214B);
+ phy_write(phydev, MDIO_DEVAD_NONE, 16, 0x2144);
+ phy_write(phydev, MDIO_DEVAD_NONE, 17, 0x0C28);
+ phy_write(phydev, MDIO_DEVAD_NONE, 16, 0x2146);
+ phy_write(phydev, MDIO_DEVAD_NONE, 17, 0xB233);
+ phy_write(phydev, MDIO_DEVAD_NONE, 16, 0x214D);
+ phy_write(phydev, MDIO_DEVAD_NONE, 17, 0xCC0C);
+ phy_write(phydev, MDIO_DEVAD_NONE, 16, 0x2159);
+ phy_write(phydev, MDIO_DEVAD_NONE, 22, 0x0000); /* reg page 0 */
+ phy_write(phydev, MDIO_DEVAD_NONE, 22, 18); /* reg page 18 */
+ /* Write HWCFG_MODE = SGMII to Copper */
+ m88e1518_phy_writebits(phydev, 20, 0, 3, 1);
+
+ /* Phy reset */
+ m88e1518_phy_writebits(phydev, 20, 15, 1, 1);
+ phy_write(phydev, MDIO_DEVAD_NONE, 22, 0); /* reg page 18 */
+ udelay(100);
+ }
+
+ return m88e1111s_config(phydev);
+}
+
/* Marvell 88E1118 */
static int m88e1118_config(struct phy_device *phydev)
{
@@ -493,7 +544,7 @@
.uid = 0x1410dd1,
.mask = 0xffffff0,
.features = PHY_GBIT_FEATURES,
- .config = &m88e1111s_config,
+ .config = &m88e1518_config,
.startup = &m88e1011s_startup,
.shutdown = &genphy_shutdown,
};
diff --git a/include/configs/am335x_evm.h b/include/configs/am335x_evm.h
index 1ec783d..560e3bf 100644
--- a/include/configs/am335x_evm.h
+++ b/include/configs/am335x_evm.h
@@ -314,6 +314,18 @@
#define CONFIG_AM335X_USB1
#define CONFIG_AM335X_USB1_MODE MUSB_HOST
+#ifndef CONFIG_SPL_USBETH_SUPPORT
+/* Fastboot */
+#define CONFIG_CMD_FASTBOOT
+#define CONFIG_ANDROID_BOOT_IMAGE
+#define CONFIG_USB_FASTBOOT_BUF_ADDR CONFIG_SYS_LOAD_ADDR
+#define CONFIG_USB_FASTBOOT_BUF_SIZE 0x07000000
+
+/* To support eMMC booting */
+#define CONFIG_STORAGE_EMMC
+#define CONFIG_FASTBOOT_FLASH_MMC_DEV 1
+#endif
+
#ifdef CONFIG_MUSB_HOST
#define CONFIG_CMD_USB
#define CONFIG_USB_STORAGE
@@ -325,8 +337,8 @@
#define CONFIG_USBNET_HOST_ADDR "de:ad:be:af:00:00"
/* USB TI's IDs */
-#define CONFIG_G_DNL_VENDOR_NUM 0x0403
-#define CONFIG_G_DNL_PRODUCT_NUM 0xBD00
+#define CONFIG_G_DNL_VENDOR_NUM 0x0451
+#define CONFIG_G_DNL_PRODUCT_NUM 0xD022
#define CONFIG_G_DNL_MANUFACTURER "Texas Instruments"
#endif /* CONFIG_MUSB_GADGET */
diff --git a/include/configs/cm_t3517.h b/include/configs/cm_t3517.h
new file mode 100644
index 0000000..918032b
--- /dev/null
+++ b/include/configs/cm_t3517.h
@@ -0,0 +1,320 @@
+/*
+ * (C) Copyright 2013 CompuLab, Ltd.
+ * Author: Igor Grinberg <grinberg@compulab.co.il>
+ *
+ * Configuration settings for the CompuLab CM-T3517 board
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ */
+#define CONFIG_OMAP /* in a TI OMAP core */
+#define CONFIG_CM_T3517 /* working with CM-T3517 */
+#define CONFIG_OMAP_COMMON
+#define CONFIG_SYS_GENERIC_BOARD
+
+#define CONFIG_SYS_TEXT_BASE 0x80008000
+
+/*
+ * This is needed for the DMA stuff.
+ * Although the default iss 64, we still define it
+ * to be on the safe side once the default is changed.
+ */
+#define CONFIG_SYS_CACHELINE_SIZE 64
+
+#define CONFIG_EMIF4 /* The chip has EMIF4 controller */
+
+#include <asm/arch/cpu.h> /* get chip and board defs */
+#include <asm/arch/omap3.h>
+
+/*
+ * Display CPU and Board information
+ */
+#define CONFIG_DISPLAY_CPUINFO
+#define CONFIG_DISPLAY_BOARDINFO
+
+/* Clock Defines */
+#define V_OSCK 26000000 /* Clock output from T2 */
+#define V_SCLK (V_OSCK >> 1)
+
+#define CONFIG_MISC_INIT_R
+
+#define CONFIG_OF_LIBFDT
+/*
+ * The early kernel mapping on ARM currently only maps from the base of DRAM
+ * to the end of the kernel image. The kernel is loaded at DRAM base + 0x8000.
+ * The early kernel pagetable uses DRAM base + 0x4000 to DRAM base + 0x8000,
+ * so that leaves DRAM base to DRAM base + 0x4000 available.
+ */
+#define CONFIG_SYS_BOOTMAPSZ 0x4000
+
+#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_INITRD_TAG
+#define CONFIG_REVISION_TAG
+#define CONFIG_SERIAL_TAG
+
+/*
+ * Size of malloc() pool
+ */
+#define CONFIG_ENV_SIZE (16 << 10) /* 16 KiB */
+#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (128 << 10))
+
+/*
+ * Hardware drivers
+ */
+
+/*
+ * NS16550 Configuration
+ */
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE (-4)
+#define CONFIG_SYS_NS16550_CLK 48000000 /* 48MHz (APLL96/2) */
+
+/*
+ * select serial console configuration
+ */
+#define CONFIG_CONS_INDEX 3
+#define CONFIG_SYS_NS16550_COM3 OMAP34XX_UART3
+#define CONFIG_SERIAL3 3 /* UART3 */
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV
+
+/* allow to overwrite serial and ethaddr */
+#define CONFIG_ENV_OVERWRITE
+#define CONFIG_BAUDRATE 115200
+#define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600,\
+ 115200}
+
+#define CONFIG_OMAP_GPIO
+
+#define CONFIG_GENERIC_MMC
+#define CONFIG_MMC
+#define CONFIG_OMAP_HSMMC
+#define CONFIG_DOS_PARTITION
+
+/* USB */
+#define CONFIG_USB_MUSB_AM35X
+
+#ifndef CONFIG_USB_MUSB_AM35X
+#define CONFIG_USB_OMAP3
+#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_OMAP
+#define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO 146
+#define CONFIG_OMAP_EHCI_PHY2_RESET_GPIO 147
+#else /* !CONFIG_USB_MUSB_AM35X */
+#define CONFIG_MUSB_HOST
+#define CONFIG_MUSB_PIO_ONLY
+#endif /* CONFIG_USB_MUSB_AM35X */
+
+#define CONFIG_USB_STORAGE
+#define CONFIG_CMD_USB
+
+/* commands to include */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_CACHE
+#define CONFIG_CMD_EXT2 /* EXT2 Support */
+#define CONFIG_CMD_FAT /* FAT support */
+#define CONFIG_CMD_MTDPARTS /* Enable MTD parts commands */
+#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */
+#define CONFIG_MTD_PARTITIONS
+#define MTDIDS_DEFAULT "nand0=nand"
+#define MTDPARTS_DEFAULT "mtdparts=nand:512k(x-loader),"\
+ "1920k(u-boot),256k(u-boot-env),"\
+ "4m(kernel),-(fs)"
+
+#define CONFIG_CMD_I2C /* I2C serial bus support */
+#define CONFIG_CMD_MMC /* MMC support */
+#define CONFIG_CMD_NAND /* NAND support */
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_GPIO
+
+#undef CONFIG_CMD_FLASH /* flinfo, erase, protect */
+#undef CONFIG_CMD_FPGA /* FPGA configuration Support */
+#undef CONFIG_CMD_IMLS /* List all found images */
+
+#define CONFIG_SYS_NO_FLASH
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_OMAP24_I2C_SPEED 400000
+#define CONFIG_SYS_OMAP24_I2C_SLAVE 1
+#define CONFIG_SYS_I2C_OMAP34XX
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
+#define CONFIG_SYS_I2C_EEPROM_BUS 0
+#define CONFIG_I2C_MULTI_BUS
+
+/*
+ * Board NAND Info.
+ */
+#define CONFIG_SYS_NAND_QUIET_TEST
+#define CONFIG_NAND_OMAP_GPMC
+#define CONFIG_SYS_NAND_ADDR NAND_BASE /* physical address */
+ /* to access nand */
+#define CONFIG_SYS_NAND_BASE NAND_BASE /* physical address */
+ /* to access nand at */
+ /* CS0 */
+#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND */
+ /* devices */
+
+/* Environment information */
+#define CONFIG_BOOTDELAY 3
+#define CONFIG_ZERO_BOOTDELAY_CHECK
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "loadaddr=0x82000000\0" \
+ "baudrate=115200\0" \
+ "console=ttyO2,115200n8\0" \
+ "mpurate=auto\0" \
+ "vram=12M\0" \
+ "dvimode=1024x768MR-16@60\0" \
+ "defaultdisplay=dvi\0" \
+ "mmcdev=0\0" \
+ "mmcroot=/dev/mmcblk0p2 rw rootwait\0" \
+ "mmcrootfstype=ext4\0" \
+ "nandroot=/dev/mtdblock4 rw\0" \
+ "nandrootfstype=ubifs\0" \
+ "mmcargs=setenv bootargs console=${console} " \
+ "mpurate=${mpurate} " \
+ "vram=${vram} " \
+ "omapfb.mode=dvi:${dvimode} " \
+ "omapdss.def_disp=${defaultdisplay} " \
+ "root=${mmcroot} " \
+ "rootfstype=${mmcrootfstype}\0" \
+ "nandargs=setenv bootargs console=${console} " \
+ "mpurate=${mpurate} " \
+ "vram=${vram} " \
+ "omapfb.mode=dvi:${dvimode} " \
+ "omapdss.def_disp=${defaultdisplay} " \
+ "root=${nandroot} " \
+ "rootfstype=${nandrootfstype}\0" \
+ "loadbootscript=fatload mmc ${mmcdev} ${loadaddr} boot.scr\0" \
+ "bootscript=echo Running bootscript from mmc ...; " \
+ "source ${loadaddr}\0" \
+ "loaduimage=fatload mmc ${mmcdev} ${loadaddr} uImage\0" \
+ "mmcboot=echo Booting from mmc ...; " \
+ "run mmcargs; " \
+ "bootm ${loadaddr}\0" \
+ "nandboot=echo Booting from nand ...; " \
+ "run nandargs; " \
+ "nand read ${loadaddr} 2a0000 400000; " \
+ "bootm ${loadaddr}\0" \
+
+#define CONFIG_CMD_BOOTZ
+#define CONFIG_BOOTCOMMAND \
+ "mmc dev ${mmcdev}; if mmc rescan; then " \
+ "if run loadbootscript; then " \
+ "run bootscript; " \
+ "else " \
+ "if run loaduimage; then " \
+ "run mmcboot; " \
+ "else run nandboot; " \
+ "fi; " \
+ "fi; " \
+ "else run nandboot; fi"
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_AUTO_COMPLETE
+#define CONFIG_CMDLINE_EDITING
+#define CONFIG_TIMESTAMP
+#define CONFIG_SYS_AUTOLOAD "no"
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */
+#define CONFIG_SYS_PROMPT "CM-T3517 # "
+#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */
+/* Print Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
+ sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_MAXARGS 32 /* max number of command args */
+/* Boot Argument Buffer Size */
+#define CONFIG_SYS_BARGSIZE (CONFIG_SYS_CBSIZE)
+
+#define CONFIG_SYS_LOAD_ADDR (OMAP34XX_SDRC_CS0 + 0x02000000)
+
+/*
+ * AM3517 has 12 GP timers, they can be driven by the system clock
+ * (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK).
+ * This rate is divided by a local divisor.
+ */
+#define CONFIG_SYS_TIMERBASE (OMAP34XX_GPT2)
+#define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */
+#define CONFIG_SYS_HZ 1000
+
+/*-----------------------------------------------------------------------
+ * Physical Memory Map
+ */
+#define CONFIG_NR_DRAM_BANKS 1 /* CM-T3517 DRAM is only on CS0 */
+#define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0
+#define CONFIG_SYS_CS0_SIZE (256 << 20)
+
+/*-----------------------------------------------------------------------
+ * FLASH and environment organization
+ */
+
+/* **** PISMO SUPPORT *** */
+/* Monitor at start of flash */
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 2 sectors */
+
+#define CONFIG_ENV_IS_IN_NAND
+#define SMNAND_ENV_OFFSET 0x260000 /* environment starts here */
+#define CONFIG_ENV_OFFSET SMNAND_ENV_OFFSET
+#define CONFIG_ENV_ADDR SMNAND_ENV_OFFSET
+
+#if defined(CONFIG_CMD_NET)
+#define CONFIG_DRIVER_TI_EMAC
+#define CONFIG_DRIVER_TI_EMAC_USE_RMII
+#define CONFIG_MII
+#define CONFIG_SMC911X
+#define CONFIG_SMC911X_32_BIT
+#define CONFIG_SMC911X_BASE (0x2C000000 + (16 << 20))
+#endif /* CONFIG_CMD_NET */
+
+/* additions for new relocation code, must be added to all boards */
+#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
+#define CONFIG_SYS_INIT_RAM_ADDR 0x4020f800
+#define CONFIG_SYS_INIT_RAM_SIZE 0x800
+#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \
+ CONFIG_SYS_INIT_RAM_SIZE - \
+ GENERATED_GBL_DATA_SIZE)
+
+/* Status LED */
+#define CONFIG_STATUS_LED /* Status LED enabled */
+#define CONFIG_BOARD_SPECIFIC_LED
+#define CONFIG_GPIO_LED
+#define GREEN_LED_GPIO 186 /* CM-T3517 Green LED is GPIO186 */
+#define GREEN_LED_DEV 0
+#define STATUS_LED_BIT GREEN_LED_GPIO
+#define STATUS_LED_STATE STATUS_LED_ON
+#define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2)
+#define STATUS_LED_BOOT GREEN_LED_DEV
+
+/* GPIO banks */
+#ifdef CONFIG_STATUS_LED
+#define CONFIG_OMAP3_GPIO_6 /* GPIO186 is in GPIO bank 6 */
+#endif
+
+/* Display Configuration */
+#define CONFIG_OMAP3_GPIO_2
+#define CONFIG_OMAP3_GPIO_5
+#define CONFIG_VIDEO_OMAP3
+#define LCD_BPP LCD_COLOR16
+
+#define CONFIG_LCD
+#define CONFIG_SPLASH_SCREEN
+#define CONFIG_SPLASHIMAGE_GUARD
+#define CONFIG_CMD_BMP
+#define CONFIG_BMP_16BPP
+#define CONFIG_SCF0403_LCD
+
+#define CONFIG_OMAP3_SPI
+
+#endif /* __CONFIG_H */
diff --git a/include/configs/k2e_evm.h b/include/configs/k2e_evm.h
index 7c8065a..d83e07e 100644
--- a/include/configs/k2e_evm.h
+++ b/include/configs/k2e_evm.h
@@ -17,14 +17,15 @@
/* U-Boot general configuration */
#define CONFIG_SYS_PROMPT "K2E EVM # "
-#define KS2_ARGS_UBI "args_ubi=setenv bootargs ${bootargs} rootfstype=ubifs "\
- "root=ubi0:rootfs rootflags=sync rw ubi.mtd=2,2048\0"
-
-#define KS2_FDT_NAME "name_fdt=k2e-evm.dtb\0"
-#define KS2_ADDR_MON "addr_mon=0x0c140000\0"
-#define KS2_NAME_MON "name_mon=skern-k2e-evm.bin\0"
-#define NAME_UBOOT "name_uboot=u-boot-spi-k2e-evm.gph\0"
-#define NAME_UBI "name_ubi=k2e-evm-ubifs.ubi\0"
+#define CONFIG_EXTRA_ENV_KS2_BOARD_SETTINGS \
+ "addr_mon=0x0c140000\0" \
+ "args_ubi=setenv bootargs ${bootargs} rootfstype=ubifs " \
+ "root=ubi0:rootfs rootflags=sync rw ubi.mtd=2,2048\0" \
+ "name_fdt=uImage-k2e-evm.dtb\0" \
+ "name_mon=skern-k2e-evm.bin\0" \
+ "name_ubi=k2e-evm-ubifs.ubi\0" \
+ "name_uboot=u-boot-spi-k2e-evm.gph\0" \
+ "name_fs=arago-console-image-k2e-evm.cpio.gz\0"
#include <configs/ks2_evm.h>
@@ -35,14 +36,8 @@
#define CONFIG_SYS_NAND_PAGE_2K
/* Network */
-#define CONFIG_DRIVER_TI_KEYSTONE_NET
-#define CONFIG_TI_KSNAV
-#define CONFIG_KSNAV_PKTDMA_NETCP
#define CONFIG_KSNET_NETCP_V1_5
#define CONFIG_KSNET_CPSW_NUM_PORTS 9
#define CONFIG_KSNET_MDIO_PHY_CONFIG_ENABLE
-/* SerDes */
-#define CONFIG_TI_KEYSTONE_SERDES
-
#endif /* __CONFIG_K2E_EVM_H */
diff --git a/include/configs/k2hk_evm.h b/include/configs/k2hk_evm.h
index 034cbfd..ffddf13 100644
--- a/include/configs/k2hk_evm.h
+++ b/include/configs/k2hk_evm.h
@@ -17,14 +17,15 @@
/* U-Boot general configuration */
#define CONFIG_SYS_PROMPT "K2HK EVM # "
-#define KS2_ARGS_UBI "args_ubi=setenv bootargs ${bootargs} rootfstype=ubifs "\
- "root=ubi0:rootfs rootflags=sync rw ubi.mtd=2,2048\0"
-
-#define KS2_FDT_NAME "name_fdt=k2hk-evm.dtb\0"
-#define KS2_ADDR_MON "addr_mon=0x0c5f0000\0"
-#define KS2_NAME_MON "name_mon=skern-k2hk-evm.bin\0"
-#define NAME_UBOOT "name_uboot=u-boot-spi-k2hk-evm.gph\0"
-#define NAME_UBI "name_ubi=k2hk-evm-ubifs.ubi\0"
+#define CONFIG_EXTRA_ENV_KS2_BOARD_SETTINGS \
+ "addr_mon=0x0c5f0000\0" \
+ "args_ubi=setenv bootargs ${bootargs} rootfstype=ubifs " \
+ "root=ubi0:rootfs rootflags=sync rw ubi.mtd=2,2048\0" \
+ "name_fdt=uImage-k2hk-evm.dtb\0" \
+ "name_mon=skern-k2hk-evm.bin\0" \
+ "name_ubi=k2hk-evm-ubifs.ubi\0" \
+ "name_uboot=u-boot-spi-k2hk-evm.gph\0" \
+ "name_fs=arago-console-image-k2hk-evm.cpio.gz\0"
#include <configs/ks2_evm.h>
@@ -35,13 +36,7 @@
#define CONFIG_SYS_NAND_PAGE_2K
/* Network */
-#define CONFIG_DRIVER_TI_KEYSTONE_NET
-#define CONFIG_TI_KSNAV
-#define CONFIG_KSNAV_PKTDMA_NETCP
#define CONFIG_KSNET_NETCP_V1_0
#define CONFIG_KSNET_CPSW_NUM_PORTS 5
-/* SerDes */
-#define CONFIG_TI_KEYSTONE_SERDES
-
#endif /* __CONFIG_K2HK_EVM_H */
diff --git a/include/configs/k2l_evm.h b/include/configs/k2l_evm.h
index 0e1f725..805164a 100644
--- a/include/configs/k2l_evm.h
+++ b/include/configs/k2l_evm.h
@@ -17,14 +17,15 @@
/* U-Boot general configuration */
#define CONFIG_SYS_PROMPT "K2L EVM # "
-#define KS2_ARGS_UBI "args_ubi=setenv bootargs ${bootargs} rootfstype=ubifs "\
- "root=ubi0:rootfs rootflags=sync rw ubi.mtd=2,4096\0"
-
-#define KS2_FDT_NAME "name_fdt=k2l-evm.dtb\0"
-#define KS2_ADDR_MON "addr_mon=0x0c140000\0"
-#define KS2_NAME_MON "name_mon=skern-k2l-evm.bin\0"
-#define NAME_UBOOT "name_uboot=u-boot-spi-k2l-evm.gph\0"
-#define NAME_UBI "name_ubi=k2l-evm-ubifs.ubi\0"
+#define CONFIG_EXTRA_ENV_KS2_BOARD_SETTINGS \
+ "addr_mon=0x0c140000\0" \
+ "args_ubi=setenv bootargs ${bootargs} rootfstype=ubifs " \
+ "root=ubi0:rootfs rootflags=sync rw ubi.mtd=2,4096\0" \
+ "name_fdt=uImage-k2l-evm.dtb\0" \
+ "name_mon=skern-k2l-evm.bin\0" \
+ "name_ubi=k2l-evm-ubifs.ubi\0" \
+ "name_uboot=u-boot-spi-k2l-evm.gph\0" \
+ "name_fs=arago-console-image-k2l-evm.cpio.gz\0"
#include <configs/ks2_evm.h>
@@ -34,4 +35,9 @@
/* NAND Configuration */
#define CONFIG_SYS_NAND_PAGE_4K
+/* Network */
+#define CONFIG_KSNET_NETCP_V1_5
+#define CONFIG_KSNET_CPSW_NUM_PORTS 5
+#define CONFIG_KSNET_MDIO_PHY_CONFIG_ENABLE
+
#endif /* __CONFIG_K2L_EVM_H */
diff --git a/include/configs/ks2_evm.h b/include/configs/ks2_evm.h
index b0c91d8..dd5050f 100644
--- a/include/configs/ks2_evm.h
+++ b/include/configs/ks2_evm.h
@@ -105,6 +105,7 @@
#define CONFIG_SYS_SGMII_RATESCALE 2
/* Keyston Navigator Configuration */
+#define CONFIG_TI_KSNAV
#define CONFIG_KSNAV_QM_BASE_ADDRESS KS2_QM_BASE_ADDRESS
#define CONFIG_KSNAV_QM_CONF_BASE KS2_QM_CONF_BASE
#define CONFIG_KSNAV_QM_DESC_SETUP_BASE KS2_QM_DESC_SETUP_BASE
@@ -121,6 +122,7 @@
#define CONFIG_KSNAV_QM_QPOOL_NUM KS2_QM_QPOOL_NUM
/* NETCP pktdma */
+#define CONFIG_KSNAV_PKTDMA_NETCP
#define CONFIG_KSNAV_NETCP_PDMA_CTRL_BASE KS2_NETCP_PDMA_CTRL_BASE
#define CONFIG_KSNAV_NETCP_PDMA_TX_BASE KS2_NETCP_PDMA_TX_BASE
#define CONFIG_KSNAV_NETCP_PDMA_TX_CH_NUM KS2_NETCP_PDMA_TX_CH_NUM
@@ -134,12 +136,16 @@
#define CONFIG_KSNAV_NETCP_PDMA_TX_SND_QUEUE KS2_NETCP_PDMA_TX_SND_QUEUE
/* Keystone net */
+#define CONFIG_DRIVER_TI_KEYSTONE_NET
#define CONFIG_KSNET_MAC_ID_BASE KS2_MAC_ID_BASE_ADDR
#define CONFIG_KSNET_NETCP_BASE KS2_NETCP_BASE
#define CONFIG_KSNET_SERDES_SGMII_BASE KS2_SGMII_SERDES_BASE
#define CONFIG_KSNET_SERDES_SGMII2_BASE KS2_SGMII_SERDES2_BASE
#define CONFIG_KSNET_SERDES_LANES_PER_SGMII KS2_LANES_PER_SGMII_SERDES
+/* SerDes */
+#define CONFIG_TI_KEYSTONE_SERDES
+
/* AEMIF */
#define CONFIG_TI_AEMIF
#define CONFIG_AEMIF_CNTRL_BASE KS2_AEMIF_CNTRL_BASE
@@ -218,6 +224,8 @@
#define CONFIG_CMD_SF
#define CONFIG_CMD_EEPROM
#define CONFIG_CMD_USB
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_FS_GENERIC
/* U-Boot general configuration */
#define CONFIG_SYS_GENERIC_BOARD
@@ -239,30 +247,25 @@
#define CONFIG_BOOTDELAY 3
#define CONFIG_BOOTFILE "uImage"
#define CONFIG_EXTRA_ENV_SETTINGS \
- "boot=ramfs\0" \
+ CONFIG_EXTRA_ENV_KS2_BOARD_SETTINGS \
+ "boot=ubi\0" \
"tftp_root=/\0" \
"nfs_root=/export\0" \
"mem_lpae=1\0" \
"mem_reserve=512M\0" \
"addr_fdt=0x87000000\0" \
"addr_kern=0x88000000\0" \
- KS2_ADDR_MON \
"addr_uboot=0x87000000\0" \
"addr_fs=0x82000000\0" \
"addr_ubi=0x82000000\0" \
"addr_secdb_key=0xc000000\0" \
"fdt_high=0xffffffff\0" \
- KS2_FDT_NAME \
- "name_fs=arago-console-image.cpio.gz\0" \
- "name_kern=uImage\0" \
- KS2_NAME_MON \
- NAME_UBOOT \
- NAME_UBI \
+ "name_kern=uImage-keystone-evm.bin\0" \
"run_mon=mon_install ${addr_mon}\0" \
"run_kern=bootm ${addr_kern} - ${addr_fdt}\0" \
"init_net=run args_all args_net\0" \
"init_ubi=run args_all args_ubi; " \
- "ubi part ubifs; ubifsmount boot;" \
+ "ubi part ubifs; ubifsmount ubi:boot;" \
"ubifsload ${addr_secdb_key} securedb.key.bin;\0" \
"get_fdt_net=dhcp ${addr_fdt} ${tftp_root}/${name_fdt}\0" \
"get_fdt_ubi=ubifsload ${addr_fdt} ${name_fdt}\0" \
@@ -276,7 +279,6 @@
"burn_uboot_nand=nand erase 0 0x100000; " \
"nand write ${addr_uboot} 0 ${filesize}\0" \
"args_all=setenv bootargs console=ttyS0,115200n8 rootwait=1\0" \
- KS2_ARGS_UBI \
"args_net=setenv bootargs ${bootargs} rootfstype=nfs " \
"root=/dev/nfs rw nfsroot=${serverip}:${nfs_root}," \
"${nfs_options} ip=dhcp\0" \
diff --git a/include/configs/omap3_igep00x0.h b/include/configs/omap3_igep00x0.h
index 006c9a9..b2b3750 100644
--- a/include/configs/omap3_igep00x0.h
+++ b/include/configs/omap3_igep00x0.h
@@ -29,8 +29,6 @@
#define CONFIG_REVISION_TAG 1
-#define CONFIG_SUPPORT_RAW_INITRD
-
/* define to enable boot progress via leds */
#if (CONFIG_MACH_TYPE == MACH_TYPE_IGEP0020) || \
(CONFIG_MACH_TYPE == MACH_TYPE_IGEP0030)
diff --git a/include/configs/ti_armv7_common.h b/include/configs/ti_armv7_common.h
index 4b9b629..a8790c2 100644
--- a/include/configs/ti_armv7_common.h
+++ b/include/configs/ti_armv7_common.h
@@ -174,6 +174,7 @@
#define CONFIG_CMD_ASKENV
#define CONFIG_CMD_ECHO
#define CONFIG_CMD_BOOTZ
+#define CONFIG_SUPPORT_RAW_INITRD
/*
* Common filesystems support. When we have removable storage we
diff --git a/include/twl4030.h b/include/twl4030.h
index 18795a6..f33cd1e 100644
--- a/include/twl4030.h
+++ b/include/twl4030.h
@@ -390,6 +390,8 @@
/* Voltage Selection in PM Receiver Module */
#define TWL4030_PM_RECEIVER_VAUX2_VSEL_18 0x05
+#define TWL4030_PM_RECEIVER_VAUX2_VSEL_28 0x09
+#define TWL4030_PM_RECEIVER_VAUX3_VSEL_18 0x01
#define TWL4030_PM_RECEIVER_VAUX3_VSEL_28 0x03
#define TWL4030_PM_RECEIVER_VPLL2_VSEL_18 0x05
#define TWL4030_PM_RECEIVER_VDAC_VSEL_18 0x03