Some code cleanup
diff --git a/CHANGELOG b/CHANGELOG
index 20f72e8..becc55c 100644
--- a/CHANGELOG
+++ b/CHANGELOG
@@ -1,19 +1,20 @@
======================================================================
Changes since U-Boot 1.1.4:
======================================================================
-* Fix dbau1x00 Board
- - Fix dbau1x00 boards broken by dbau1550 patch
- PLL:s were not set for boards other than 1550.
- Flash CFI caused card to hang due to undefined CFG_FLASH_BANKS_LIST.
- Default boot is now bootp for cards other than 1550.
- Patch by Thomas Lange Aug 10 2005
+
+* Some code cleanup
+
+* Fix dbau1x00 boards broken by dbau1550 patch
+ PLL:s were not set for boards other than 1550.
+ Flash CFI caused card to hang due to undefined CFG_FLASH_BANKS_LIST.
+ Default boot is now bootp for cards other than 1550.
+ Patch by Thomas Lange, 10 Aug 2005
* Fixes common/cmd_flash.c:
-
- - fix some compiler/parser error, if using m68k tool chain
- - optical fix for protect on/off all messages, if using more
- then one bank
- Patch by Jens Scharsig, 28 July 2005
+ - fix some compiler/parser error, if using m68k tool chain
+ - optical fix for protect on/off all messages, if using more
+ then one bank
+ Patch by Jens Scharsig, 28 Jul 2005
* Fix Quad UART mapping on MCC200 board due to new HW revision
@@ -57,18 +58,18 @@
* Updates to common PPC4xx onboard (DDR)SDRAM init code (405 and 440)
405 SDRAM: - The SDRAM parameters can now be defined in the board
- config file and the 405 SDRAM controller values will
- be calculated upon bootup (see PPChameleonEVB).
- When those settings are not defined in the board
- config file, the register setup will be as it is now,
- so this implementation should not break any current
- design using this code.
+ config file and the 405 SDRAM controller values will
+ be calculated upon bootup (see PPChameleonEVB).
+ When those settings are not defined in the board
+ config file, the register setup will be as it is now,
+ so this implementation should not break any current
+ design using this code.
- Thanks to Andrea Marson from DAVE for this patch.
+ Thanks to Andrea Marson from DAVE for this patch.
440 DDR: - Added function sdram_tr1_set to auto calculate the
- TR1 value for the DDR.
- - Added ECC support (see p3p440).
+ TR1 value for the DDR.
+ - Added ECC support (see p3p440).
Patch by Stefan Roese, 17 Mar 2006
@@ -442,7 +443,7 @@
are removed from the default U-Boot build.
Enable DEBUG for lib_arm/board.c to enable debug messages.
New CONFIG_DISPLAY_CPUINFO and CONFIG_DISPLAY_BOARDINFO options.
- Patch by Stefan Roese, 24 Jan 2006
+ Patch by Stefan Roese, 24 Jan 2006
* Fix various compiler warnings on ppc4xx builds (ELDK 4.0)
Patch by Stefan Roese, 18 Jan 2006
@@ -588,11 +589,11 @@
* Add support for multiple PHYs.
Tested on the following boards:
- cmcpu2 (at91rm9200/ether.c)
+ cmcpu2 (at91rm9200/ether.c)
PPChameleon (ppc4xx/4xx_enet.c)
- yukon (mpc8220/fec.c)
- uc100 (mpc8xx/fec.c)
- tqm834x (mpc834x/tsec.c) with EEPRO100
+ yukon (mpc8220/fec.c)
+ uc100 (mpc8xx/fec.c)
+ tqm834x (mpc834x/tsec.c) with EEPRO100
lite5200 (mpc5xxx/fec.c) with EEPRO100 card (drivers/eepro100.c)
Main changes include:
common/miiphyutil.c
@@ -1132,18 +1133,18 @@
The first one is to define a single, static partition:
#undef CONFIG_JFFS2_CMDLINE
- #define CONFIG_JFFS2_DEV "nor0"
- #define CONFIG_JFFS2_PART_SIZE 0xFFFFFFFF /* use whole device */
- #define CONFIG_JFFS2_PART_SIZE 0x00100000 /* use 1MB */
- #define CONFIG_JFFS2_PART_OFFSET 0x00000000
+ #define CONFIG_JFFS2_DEV "nor0"
+ #define CONFIG_JFFS2_PART_SIZE 0xFFFFFFFF /* use whole device */
+ #define CONFIG_JFFS2_PART_SIZE 0x00100000 /* use 1MB */
+ #define CONFIG_JFFS2_PART_OFFSET 0x00000000
The second method uses the mtdparts command line option and dynamic
partitioning:
/* mtdparts command line support */
#define CONFIG_JFFS2_CMDLINE
- #define MTDIDS_DEFAULT "nor1=zuma-1,nor2=zuma-2"
- #define MTDPARTS_DEFAULT "mtdparts=zuma-1:-(jffs2),zuma-2:-(user)"
+ #define MTDIDS_DEFAULT "nor1=zuma-1,nor2=zuma-2"
+ #define MTDPARTS_DEFAULT "mtdparts=zuma-1:-(jffs2),zuma-2:-(user)"
Command line of course produces bigger images, and may be inappropriate
for some targets, so by default it's off.
@@ -3456,7 +3457,7 @@
Bring ARM memory layout in sync with the documentation:
stack and malloc-heap are now located _below_ the U-Boot code
-* Accelerate booting on TRAB board: read and check autoupdate image
+* Accelerate booting on TRAB board: read and check autoupdate image
headers first instead of always reading the whole images.
* Fix type in MPC5XXX code (pointed out by Victor Wren)
@@ -3576,7 +3577,7 @@
* Make 5200 reset command _really_ reset the board, without running
any other code after it
-* Fix errors with flash erase when range spans across banks
+* Fix errors with flash erase when range spans across banks
that are mapped in reverse order
* Fix flash mapping and display on P3G4 board
@@ -3820,7 +3821,7 @@
or 1 x AM29LV652 (two LV065 in one chip = 16 MB);
Run IPB at 133 Mhz; adjust the MII clock frequency accordingly
-* Set BRG_CLK on PM825/826 to 64MHz (VCO_OUT / 4, instead of 16 MHz)
+* Set BRG_CLK on PM825/826 to 64MHz (VCO_OUT / 4, instead of 16 MHz)
to allow for more accurate baudrate settings
(error now 0.7% at 115 kbps, instead of 3.5% before)
@@ -4307,7 +4308,7 @@
Update for MPC8266ADS board
* Get (mostly) rid of CFG_MONITOR_LEN definition; compute real length
- instead CFG_MONITOR_LEN is now only used to determine _at_compile_
+ instead CFG_MONITOR_LEN is now only used to determine _at_compile_
_time_ (!) if the environment is embedded within the U-Boot image,
or in a separate flash sector.
@@ -4357,7 +4358,7 @@
* Patch by Thomas Schäfer, 28 Apr 2003:
Fix SPD handling for 256 ECC DIMM on Walnut
-* Add support for arbitrary bitmaps for TRAB's VFD command;
+* Add support for arbitrary bitmaps for TRAB's VFD command;
allow to pass boot bitmap addresses in environment variables;
allow for zero boot delay
@@ -4700,7 +4701,7 @@
* Add VFD type detection to trab board
-* extend drivers/cs8900.c driver to synchronize ethaddr environment
+* extend drivers/cs8900.c driver to synchronize ethaddr environment
variable with value in the EEPROM
* Patch by Stefan Roese, 10 Feb 2003:
@@ -4860,7 +4861,7 @@
* Patch by Pierre Aubert, 05 Nov 2002
Add support for slave serial Spartan 2 FPGAs
-* Fix uninitialized memory (MAC address) in 8xx SCC/FEC ethernet
+* Fix uninitialized memory (MAC address) in 8xx SCC/FEC ethernet
drivers
* Add support for log buffer which can be passed to Linux kernel's
diff --git a/README b/README
index ae9e10f..3ae9cfc 100644
--- a/README
+++ b/README
@@ -307,7 +307,7 @@
CONFIG_ARMADILLO, CONFIG_AT91RM9200DK, CONFIG_CERF250,
CONFIG_CSB637, CONFIG_DELTA, CONFIG_DNP1110,
CONFIG_EP7312, CONFIG_H2_OMAP1610, CONFIG_HHP_CRADLE,
- CONFIG_IMPA7, CONFIG_INNOVATOROMAP1510, CONFIG_INNOVATOROMAP1610,
+ CONFIG_IMPA7, CONFIG_INNOVATOROMAP1510, CONFIG_INNOVATOROMAP1610,
CONFIG_KB9202, CONFIG_LART, CONFIG_LPD7A400,
CONFIG_LUBBOCK, CONFIG_OSK_OMAP5912, CONFIG_OMAP2420H4,
CONFIG_SHANNON, CONFIG_P2_OMAP730, CONFIG_SMDK2400,
@@ -388,12 +388,12 @@
frequency is this value multiplied by 13 MHz.
CFG_MONAHANS_TURBO_RUN_MODE_RATIO
-
+
Defines the Monahans turbo mode to oscillator
ratio. Valid values are 1 (default if undefined) and
- 2. The core frequency as calculated above is multiplied
+ 2. The core frequency as calculated above is multiplied
by this value.
-
+
- Linux Kernel Interface:
CONFIG_CLOCKS_IN_MHZ
diff --git a/board/icecube/icecube.c b/board/icecube/icecube.c
index 4197a7c..4f056b2 100644
--- a/board/icecube/icecube.c
+++ b/board/icecube/icecube.c
@@ -187,17 +187,17 @@
#endif /* CFG_RAMBOOT */
/*
- * On MPC5200B we need to set the special configuration delay in the
- * DDR controller. Please refer to Freescale's AN3221 "MPC5200B SDRAM
+ * On MPC5200B we need to set the special configuration delay in the
+ * DDR controller. Please refer to Freescale's AN3221 "MPC5200B SDRAM
* Initialization and Configuration", 3.3.1 SDelay--MBAR + 0x0190:
*
- * "The SDelay should be written to a value of 0x00000004. It is
- * required to account for changes caused by normal wafer processing
+ * "The SDelay should be written to a value of 0x00000004. It is
+ * required to account for changes caused by normal wafer processing
* parameters."
- */
+ */
svr = get_svr();
pvr = get_pvr();
- if ((SVR_MJREV(svr) >= 2) &&
+ if ((SVR_MJREV(svr) >= 2) &&
(PVR_MAJ(pvr) == 1) && (PVR_MIN(pvr) == 4)) {
*(vu_long *)MPC5XXX_SDRAM_SDELAY = 0x04;
diff --git a/board/mpc8349emds/mpc8349emds.c b/board/mpc8349emds/mpc8349emds.c
index 73a33f6..7ece7db 100644
--- a/board/mpc8349emds/mpc8349emds.c
+++ b/board/mpc8349emds/mpc8349emds.c
@@ -116,14 +116,14 @@
im->ddr.csbnds[2].csbnds = 0x0000000f;
im->ddr.cs_config[2] = CFG_DDR_CONFIG;
- /* currently we use only one CS, so disable the other banks */
+ /* currently we use only one CS, so disable the other banks */
im->ddr.cs_config[0] = 0;
im->ddr.cs_config[1] = 0;
im->ddr.cs_config[3] = 0;
im->ddr.timing_cfg_1 = CFG_DDR_TIMING_1;
im->ddr.timing_cfg_2 = CFG_DDR_TIMING_2;
-
+
im->ddr.sdram_cfg =
SDRAM_CFG_SREN
#if defined(CONFIG_DDR_2T_TIMING)
@@ -136,7 +136,7 @@
#endif
im->ddr.sdram_mode = CFG_DDR_MODE;
- im->ddr.sdram_interval = CFG_DDR_INTERVAL;
+ im->ddr.sdram_interval = CFG_DDR_INTERVAL;
udelay(200);
/* enable DDR controller */
@@ -361,12 +361,12 @@
volatile u32 val;
u64 *addr, count, val64;
register u64 *i;
-
+
if (argc > 4) {
printf ("Usage:\n%s\n", cmdtp->usage);
return 1;
}
-
+
if (argc == 2) {
if (strcmp(argv[1], "status") == 0) {
ecc_print_status();
@@ -379,8 +379,8 @@
ddr->capture_attributes = 0;
return 0;
}
- }
-
+ }
+
if (argc == 3) {
if (strcmp(argv[1], "sbecnt") == 0) {
val = simple_strtoul(argv[2], NULL, 10);
@@ -416,8 +416,8 @@
} else if (strcmp(argv[2], "+mse") == 0) {
val |= ECC_ERROR_DISABLE_MSED;
} else if (strcmp(argv[2], "+all") == 0) {
- val |= (ECC_ERROR_DISABLE_SBED |
- ECC_ERROR_DISABLE_MBED |
+ val |= (ECC_ERROR_DISABLE_SBED |
+ ECC_ERROR_DISABLE_MBED |
ECC_ERROR_DISABLE_MSED);
} else if (strcmp(argv[2], "-sbe") == 0) {
val &= ~ECC_ERROR_DISABLE_SBED;
@@ -426,8 +426,8 @@
} else if (strcmp(argv[2], "-mse") == 0) {
val &= ~ECC_ERROR_DISABLE_MSED;
} else if (strcmp(argv[2], "-all") == 0) {
- val &= ~(ECC_ERROR_DISABLE_SBED |
- ECC_ERROR_DISABLE_MBED |
+ val &= ~(ECC_ERROR_DISABLE_SBED |
+ ECC_ERROR_DISABLE_MBED |
ECC_ERROR_DISABLE_MSED);
} else {
printf("Incorrect err_disable field\n");
diff --git a/board/mx1ads/mx1ads.c b/board/mx1ads/mx1ads.c
index 913f95c..abf2fd5 100644
--- a/board/mx1ads/mx1ads.c
+++ b/board/mx1ads/mx1ads.c
@@ -85,7 +85,7 @@
GPCR = 0x000003AB; /* I/O pad driving strength */
- /* MX1_CS1U = 0x00000A00; *//* SRAM initialization */
+ /* MX1_CS1U = 0x00000A00; */ /* SRAM initialization */
/* MX1_CS1L = 0x11110601; */
MPCTL0 = 0x04632410; /* setting for 150 MHz MCU PLL CLK */
diff --git a/common/cmd_load.c b/common/cmd_load.c
index 31fef81..2432ee2 100644
--- a/common/cmd_load.c
+++ b/common/cmd_load.c
@@ -973,7 +973,7 @@
}
static int getcxmodem(void) {
- if (tstc())
+ if (tstc())
return (getc());
return -1;
}
@@ -984,49 +984,51 @@
int err;
int res;
connection_info_t info;
- char ymodemBuf[1024];
- ulong store_addr = ~0;
- ulong addr = 0;
+ char ymodemBuf[1024];
+ ulong store_addr = ~0;
+ ulong addr = 0;
- size=0;
- info.mode=xyzModem_ymodem;
- res=xyzModem_stream_open(&info, &err);
+ size = 0;
+ info.mode = xyzModem_ymodem;
+ res = xyzModem_stream_open (&info, &err);
if (!res) {
-
- while ((res=xyzModem_stream_read(ymodemBuf, 1024, &err)) > 0 ){
- store_addr = addr + offset;
- size+=res;
- addr+=res;
-#ifndef CFG_NO_FLASH
- if (addr2info(store_addr)) {
- int rc;
- rc = flash_write((char *)ymodemBuf,store_addr,res);
- if (rc != 0) {
- flash_perror (rc);
- return (~0);
- }
- } else
+ while ((res =
+ xyzModem_stream_read (ymodemBuf, 1024, &err)) > 0) {
+ store_addr = addr + offset;
+ size += res;
+ addr += res;
+#ifndef CFG_NO_FLASH
+ if (addr2info (store_addr)) {
+ int rc;
+
+ rc = flash_write ((char *) ymodemBuf,
+ store_addr, res);
+ if (rc != 0) {
+ flash_perror (rc);
+ return (~0);
+ }
+ } else
#endif
- {
- memcpy ((char *)(store_addr), ymodemBuf, res);
- }
-
- }
- }
- else {
- printf ("%s\n",xyzModem_error(err));
+ {
+ memcpy ((char *) (store_addr), ymodemBuf,
+ res);
+ }
+
+ }
+ } else {
+ printf ("%s\n", xyzModem_error (err));
}
-
- xyzModem_stream_close(&err);
- xyzModem_stream_terminate(false,&getcxmodem);
+
+ xyzModem_stream_close (&err);
+ xyzModem_stream_terminate (false, &getcxmodem);
flush_cache (offset, size);
- printf("## Total Size = 0x%08x = %d Bytes\n", size, size);
- sprintf(buf, "%X", size);
- setenv("filesize", buf);
+ printf ("## Total Size = 0x%08x = %d Bytes\n", size, size);
+ sprintf (buf, "%X", size);
+ setenv ("filesize", buf);
return offset;
}
diff --git a/common/crc16.c b/common/crc16.c
index d571405..3cef106 100644
--- a/common/crc16.c
+++ b/common/crc16.c
@@ -1,94 +1,96 @@
-//==========================================================================
-//
-// crc16.c
-//
-// 16 bit CRC with polynomial x^16+x^12+x^5+1
-//
-//==========================================================================
-//####ECOSGPLCOPYRIGHTBEGIN####
-// -------------------------------------------
-// This file is part of eCos, the Embedded Configurable Operating System.
-// Copyright (C) 1998, 1999, 2000, 2001, 2002 Red Hat, Inc.
-// Copyright (C) 2002 Gary Thomas
-//
-// eCos is free software; you can redistribute it and/or modify it under
-// the terms of the GNU General Public License as published by the Free
-// Software Foundation; either version 2 or (at your option) any later version.
-//
-// eCos is distributed in the hope that it will be useful, but WITHOUT ANY
-// WARRANTY; without even the implied warranty of MERCHANTABILITY or
-// FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
-// for more details.
-//
-// You should have received a copy of the GNU General Public License along
-// with eCos; if not, write to the Free Software Foundation, Inc.,
-// 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA.
-//
-// As a special exception, if other files instantiate templates or use macros
-// or inline functions from this file, or you compile this file and link it
-// with other works to produce a work based on this file, this file does not
-// by itself cause the resulting work to be covered by the GNU General Public
-// License. However the source code for this file must still be made available
-// in accordance with section (3) of the GNU General Public License.
-//
-// This exception does not invalidate any other reasons why a work based on
-// this file might be covered by the GNU General Public License.
-//
-// Alternative licenses for eCos may be arranged by contacting Red Hat, Inc.
-// at http://sources.redhat.com/ecos/ecos-license/
-// -------------------------------------------
-//####ECOSGPLCOPYRIGHTEND####
-//==========================================================================
-//#####DESCRIPTIONBEGIN####
-//
-// Author(s): gthomas
-// Contributors: gthomas,asl
-// Date: 2001-01-31
-// Purpose:
-// Description:
-//
-// This code is part of eCos (tm).
-//
-//####DESCRIPTIONEND####
-//
-//==========================================================================
+/*
+ *==========================================================================
+ *
+ * crc16.c
+ *
+ * 16 bit CRC with polynomial x^16+x^12+x^5+1
+ *
+ *==========================================================================
+ *####ECOSGPLCOPYRIGHTBEGIN####
+ * -------------------------------------------
+ * This file is part of eCos, the Embedded Configurable Operating System.
+ * Copyright (C) 1998, 1999, 2000, 2001, 2002 Red Hat, Inc.
+ * Copyright (C) 2002 Gary Thomas
+ *
+ * eCos is free software; you can redistribute it and/or modify it under
+ * the terms of the GNU General Public License as published by the Free
+ * Software Foundation; either version 2 or (at your option) any later version.
+ *
+ * eCos is distributed in the hope that it will be useful, but WITHOUT ANY
+ * WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
+ * for more details.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with eCos; if not, write to the Free Software Foundation, Inc.,
+ * 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA.
+ *
+ * As a special exception, if other files instantiate templates or use macros
+ * or inline functions from this file, or you compile this file and link it
+ * with other works to produce a work based on this file, this file does not
+ * by itself cause the resulting work to be covered by the GNU General Public
+ * License. However the source code for this file must still be made available
+ * in accordance with section (3) of the GNU General Public License.
+ *
+ * This exception does not invalidate any other reasons why a work based on
+ * this file might be covered by the GNU General Public License.
+ *
+ * Alternative licenses for eCos may be arranged by contacting Red Hat, Inc.
+ * at http: *sources.redhat.com/ecos/ecos-license/
+ * -------------------------------------------
+ *####ECOSGPLCOPYRIGHTEND####
+ *==========================================================================
+ *#####DESCRIPTIONBEGIN####
+ *
+ * Author(s): gthomas
+ * Contributors: gthomas,asl
+ * Date: 2001-01-31
+ * Purpose:
+ * Description:
+ *
+ * This code is part of eCos (tm).
+ *
+ *####DESCRIPTIONEND####
+ *
+ *==========================================================================
+ */
#include "crc.h"
-// Table of CRC constants - implements x^16+x^12+x^5+1
+/* Table of CRC constants - implements x^16+x^12+x^5+1 */
static const uint16_t crc16_tab[] = {
- 0x0000, 0x1021, 0x2042, 0x3063, 0x4084, 0x50a5, 0x60c6, 0x70e7,
- 0x8108, 0x9129, 0xa14a, 0xb16b, 0xc18c, 0xd1ad, 0xe1ce, 0xf1ef,
- 0x1231, 0x0210, 0x3273, 0x2252, 0x52b5, 0x4294, 0x72f7, 0x62d6,
- 0x9339, 0x8318, 0xb37b, 0xa35a, 0xd3bd, 0xc39c, 0xf3ff, 0xe3de,
- 0x2462, 0x3443, 0x0420, 0x1401, 0x64e6, 0x74c7, 0x44a4, 0x5485,
- 0xa56a, 0xb54b, 0x8528, 0x9509, 0xe5ee, 0xf5cf, 0xc5ac, 0xd58d,
- 0x3653, 0x2672, 0x1611, 0x0630, 0x76d7, 0x66f6, 0x5695, 0x46b4,
- 0xb75b, 0xa77a, 0x9719, 0x8738, 0xf7df, 0xe7fe, 0xd79d, 0xc7bc,
- 0x48c4, 0x58e5, 0x6886, 0x78a7, 0x0840, 0x1861, 0x2802, 0x3823,
- 0xc9cc, 0xd9ed, 0xe98e, 0xf9af, 0x8948, 0x9969, 0xa90a, 0xb92b,
- 0x5af5, 0x4ad4, 0x7ab7, 0x6a96, 0x1a71, 0x0a50, 0x3a33, 0x2a12,
- 0xdbfd, 0xcbdc, 0xfbbf, 0xeb9e, 0x9b79, 0x8b58, 0xbb3b, 0xab1a,
- 0x6ca6, 0x7c87, 0x4ce4, 0x5cc5, 0x2c22, 0x3c03, 0x0c60, 0x1c41,
- 0xedae, 0xfd8f, 0xcdec, 0xddcd, 0xad2a, 0xbd0b, 0x8d68, 0x9d49,
- 0x7e97, 0x6eb6, 0x5ed5, 0x4ef4, 0x3e13, 0x2e32, 0x1e51, 0x0e70,
- 0xff9f, 0xefbe, 0xdfdd, 0xcffc, 0xbf1b, 0xaf3a, 0x9f59, 0x8f78,
- 0x9188, 0x81a9, 0xb1ca, 0xa1eb, 0xd10c, 0xc12d, 0xf14e, 0xe16f,
- 0x1080, 0x00a1, 0x30c2, 0x20e3, 0x5004, 0x4025, 0x7046, 0x6067,
- 0x83b9, 0x9398, 0xa3fb, 0xb3da, 0xc33d, 0xd31c, 0xe37f, 0xf35e,
- 0x02b1, 0x1290, 0x22f3, 0x32d2, 0x4235, 0x5214, 0x6277, 0x7256,
- 0xb5ea, 0xa5cb, 0x95a8, 0x8589, 0xf56e, 0xe54f, 0xd52c, 0xc50d,
- 0x34e2, 0x24c3, 0x14a0, 0x0481, 0x7466, 0x6447, 0x5424, 0x4405,
- 0xa7db, 0xb7fa, 0x8799, 0x97b8, 0xe75f, 0xf77e, 0xc71d, 0xd73c,
- 0x26d3, 0x36f2, 0x0691, 0x16b0, 0x6657, 0x7676, 0x4615, 0x5634,
- 0xd94c, 0xc96d, 0xf90e, 0xe92f, 0x99c8, 0x89e9, 0xb98a, 0xa9ab,
- 0x5844, 0x4865, 0x7806, 0x6827, 0x18c0, 0x08e1, 0x3882, 0x28a3,
- 0xcb7d, 0xdb5c, 0xeb3f, 0xfb1e, 0x8bf9, 0x9bd8, 0xabbb, 0xbb9a,
- 0x4a75, 0x5a54, 0x6a37, 0x7a16, 0x0af1, 0x1ad0, 0x2ab3, 0x3a92,
- 0xfd2e, 0xed0f, 0xdd6c, 0xcd4d, 0xbdaa, 0xad8b, 0x9de8, 0x8dc9,
- 0x7c26, 0x6c07, 0x5c64, 0x4c45, 0x3ca2, 0x2c83, 0x1ce0, 0x0cc1,
- 0xef1f, 0xff3e, 0xcf5d, 0xdf7c, 0xaf9b, 0xbfba, 0x8fd9, 0x9ff8,
- 0x6e17, 0x7e36, 0x4e55, 0x5e74, 0x2e93, 0x3eb2, 0x0ed1, 0x1ef0,
+ 0x0000, 0x1021, 0x2042, 0x3063, 0x4084, 0x50a5, 0x60c6, 0x70e7,
+ 0x8108, 0x9129, 0xa14a, 0xb16b, 0xc18c, 0xd1ad, 0xe1ce, 0xf1ef,
+ 0x1231, 0x0210, 0x3273, 0x2252, 0x52b5, 0x4294, 0x72f7, 0x62d6,
+ 0x9339, 0x8318, 0xb37b, 0xa35a, 0xd3bd, 0xc39c, 0xf3ff, 0xe3de,
+ 0x2462, 0x3443, 0x0420, 0x1401, 0x64e6, 0x74c7, 0x44a4, 0x5485,
+ 0xa56a, 0xb54b, 0x8528, 0x9509, 0xe5ee, 0xf5cf, 0xc5ac, 0xd58d,
+ 0x3653, 0x2672, 0x1611, 0x0630, 0x76d7, 0x66f6, 0x5695, 0x46b4,
+ 0xb75b, 0xa77a, 0x9719, 0x8738, 0xf7df, 0xe7fe, 0xd79d, 0xc7bc,
+ 0x48c4, 0x58e5, 0x6886, 0x78a7, 0x0840, 0x1861, 0x2802, 0x3823,
+ 0xc9cc, 0xd9ed, 0xe98e, 0xf9af, 0x8948, 0x9969, 0xa90a, 0xb92b,
+ 0x5af5, 0x4ad4, 0x7ab7, 0x6a96, 0x1a71, 0x0a50, 0x3a33, 0x2a12,
+ 0xdbfd, 0xcbdc, 0xfbbf, 0xeb9e, 0x9b79, 0x8b58, 0xbb3b, 0xab1a,
+ 0x6ca6, 0x7c87, 0x4ce4, 0x5cc5, 0x2c22, 0x3c03, 0x0c60, 0x1c41,
+ 0xedae, 0xfd8f, 0xcdec, 0xddcd, 0xad2a, 0xbd0b, 0x8d68, 0x9d49,
+ 0x7e97, 0x6eb6, 0x5ed5, 0x4ef4, 0x3e13, 0x2e32, 0x1e51, 0x0e70,
+ 0xff9f, 0xefbe, 0xdfdd, 0xcffc, 0xbf1b, 0xaf3a, 0x9f59, 0x8f78,
+ 0x9188, 0x81a9, 0xb1ca, 0xa1eb, 0xd10c, 0xc12d, 0xf14e, 0xe16f,
+ 0x1080, 0x00a1, 0x30c2, 0x20e3, 0x5004, 0x4025, 0x7046, 0x6067,
+ 0x83b9, 0x9398, 0xa3fb, 0xb3da, 0xc33d, 0xd31c, 0xe37f, 0xf35e,
+ 0x02b1, 0x1290, 0x22f3, 0x32d2, 0x4235, 0x5214, 0x6277, 0x7256,
+ 0xb5ea, 0xa5cb, 0x95a8, 0x8589, 0xf56e, 0xe54f, 0xd52c, 0xc50d,
+ 0x34e2, 0x24c3, 0x14a0, 0x0481, 0x7466, 0x6447, 0x5424, 0x4405,
+ 0xa7db, 0xb7fa, 0x8799, 0x97b8, 0xe75f, 0xf77e, 0xc71d, 0xd73c,
+ 0x26d3, 0x36f2, 0x0691, 0x16b0, 0x6657, 0x7676, 0x4615, 0x5634,
+ 0xd94c, 0xc96d, 0xf90e, 0xe92f, 0x99c8, 0x89e9, 0xb98a, 0xa9ab,
+ 0x5844, 0x4865, 0x7806, 0x6827, 0x18c0, 0x08e1, 0x3882, 0x28a3,
+ 0xcb7d, 0xdb5c, 0xeb3f, 0xfb1e, 0x8bf9, 0x9bd8, 0xabbb, 0xbb9a,
+ 0x4a75, 0x5a54, 0x6a37, 0x7a16, 0x0af1, 0x1ad0, 0x2ab3, 0x3a92,
+ 0xfd2e, 0xed0f, 0xdd6c, 0xcd4d, 0xbdaa, 0xad8b, 0x9de8, 0x8dc9,
+ 0x7c26, 0x6c07, 0x5c64, 0x4c45, 0x3ca2, 0x2c83, 0x1ce0, 0x0cc1,
+ 0xef1f, 0xff3e, 0xcf5d, 0xdf7c, 0xaf9b, 0xbfba, 0x8fd9, 0x9ff8,
+ 0x6e17, 0x7e36, 0x4e55, 0x5e74, 0x2e93, 0x3eb2, 0x0ed1, 0x1ef0,
};
uint16_t
@@ -103,4 +105,3 @@
}
return cksum;
}
-
diff --git a/common/xyzModem.c b/common/xyzModem.c
index 3c86b13..4a137bf 100644
--- a/common/xyzModem.c
+++ b/common/xyzModem.c
@@ -1,65 +1,67 @@
-//==========================================================================
-//
-// xyzModem.c
-//
-// RedBoot stream handler for xyzModem protocol
-//
-//==========================================================================
-//####ECOSGPLCOPYRIGHTBEGIN####
-// -------------------------------------------
-// This file is part of eCos, the Embedded Configurable Operating System.
-// Copyright (C) 1998, 1999, 2000, 2001, 2002 Red Hat, Inc.
-// Copyright (C) 2002 Gary Thomas
-//
-// eCos is free software; you can redistribute it and/or modify it under
-// the terms of the GNU General Public License as published by the Free
-// Software Foundation; either version 2 or (at your option) any later version.
-//
-// eCos is distributed in the hope that it will be useful, but WITHOUT ANY
-// WARRANTY; without even the implied warranty of MERCHANTABILITY or
-// FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
-// for more details.
-//
-// You should have received a copy of the GNU General Public License along
-// with eCos; if not, write to the Free Software Foundation, Inc.,
-// 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA.
-//
-// As a special exception, if other files instantiate templates or use macros
-// or inline functions from this file, or you compile this file and link it
-// with other works to produce a work based on this file, this file does not
-// by itself cause the resulting work to be covered by the GNU General Public
-// License. However the source code for this file must still be made available
-// in accordance with section (3) of the GNU General Public License.
-//
-// This exception does not invalidate any other reasons why a work based on
-// this file might be covered by the GNU General Public License.
-//
-// Alternative licenses for eCos may be arranged by contacting Red Hat, Inc.
-// at http://sources.redhat.com/ecos/ecos-license/
-// -------------------------------------------
-//####ECOSGPLCOPYRIGHTEND####
-//==========================================================================
-//#####DESCRIPTIONBEGIN####
-//
-// Author(s): gthomas
-// Contributors: gthomas, tsmith, Yoshinori Sato
-// Date: 2000-07-14
-// Purpose:
-// Description:
-//
-// This code is part of RedBoot (tm).
-//
-//####DESCRIPTIONEND####
-//
-//==========================================================================
+/*
+ *==========================================================================
+ *
+ * xyzModem.c
+ *
+ * RedBoot stream handler for xyzModem protocol
+ *
+ *==========================================================================
+ *####ECOSGPLCOPYRIGHTBEGIN####
+ * -------------------------------------------
+ * This file is part of eCos, the Embedded Configurable Operating System.
+ * Copyright (C) 1998, 1999, 2000, 2001, 2002 Red Hat, Inc.
+ * Copyright (C) 2002 Gary Thomas
+ *
+ * eCos is free software; you can redistribute it and/or modify it under
+ * the terms of the GNU General Public License as published by the Free
+ * Software Foundation; either version 2 or (at your option) any later version.
+ *
+ * eCos is distributed in the hope that it will be useful, but WITHOUT ANY
+ * WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
+ * for more details.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with eCos; if not, write to the Free Software Foundation, Inc.,
+ * 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA.
+ *
+ * As a special exception, if other files instantiate templates or use macros
+ * or inline functions from this file, or you compile this file and link it
+ * with other works to produce a work based on this file, this file does not
+ * by itself cause the resulting work to be covered by the GNU General Public
+ * License. However the source code for this file must still be made available
+ * in accordance with section (3) of the GNU General Public License.
+ *
+ * This exception does not invalidate any other reasons why a work based on
+ * this file might be covered by the GNU General Public License.
+ *
+ * Alternative licenses for eCos may be arranged by contacting Red Hat, Inc.
+ * at http: *sources.redhat.com/ecos/ecos-license/
+ * -------------------------------------------
+ *####ECOSGPLCOPYRIGHTEND####
+ *==========================================================================
+ *#####DESCRIPTIONBEGIN####
+ *
+ * Author(s): gthomas
+ * Contributors: gthomas, tsmith, Yoshinori Sato
+ * Date: 2000-07-14
+ * Purpose:
+ * Description:
+ *
+ * This code is part of RedBoot (tm).
+ *
+ *####DESCRIPTIONEND####
+ *
+ *==========================================================================
+ */
#include <common.h>
#include <xyzModem.h>
#include <stdarg.h>
#include <crc.h>
-// Assumption - run xyzModem protocol over the console port
+/* Assumption - run xyzModem protocol over the console port */
-// Values magic to the protocol
+/* Values magic to the protocol */
#define SOH 0x01
#define STX 0x02
#define EOT 0x04
@@ -67,11 +69,11 @@
#define BSP 0x08
#define NAK 0x15
#define CAN 0x18
-#define EOF 0x1A // ^Z for DOS officionados
+#define EOF 0x1A /* ^Z for DOS officionados */
#define USE_YMODEM_LENGTH
-// Data & state local to the protocol
+/* Data & state local to the protocol */
static struct {
#ifdef REDBOOT
hal_virtual_comm_table_t* __chan;
@@ -80,7 +82,7 @@
#endif
unsigned char pkt[1024], *bufp;
unsigned char blk,cblk,crc1,crc2;
- unsigned char next_blk; // Expected block
+ unsigned char next_blk; /* Expected block */
int len, mode, total_retries;
int total_SOH, total_STX, total_CAN;
bool crc_mode, at_eof, tx_ack;
@@ -89,13 +91,13 @@
#endif
} xyz;
-#define xyzModem_CHAR_TIMEOUT 2000 // 2 seconds
+#define xyzModem_CHAR_TIMEOUT 2000 /* 2 seconds */
#define xyzModem_MAX_RETRIES 20
#define xyzModem_MAX_RETRIES_WITH_CRC 10
-#define xyzModem_CAN_COUNT 3 // Wait for 3 CAN before quitting
+#define xyzModem_CAN_COUNT 3 /* Wait for 3 CAN before quitting */
-#ifndef REDBOOT //SB
+#ifndef REDBOOT /*SB */
typedef int cyg_int32;
int CYGACC_COMM_IF_GETC_TIMEOUT (char chan,char *c) {
#define DELAY 20
@@ -115,7 +117,7 @@
putc(y);
}
-// Validate a hex character
+/* Validate a hex character */
__inline__ static bool
_is_hex(char c)
{
@@ -124,7 +126,7 @@
((c >= 'a') && (c <= 'f')));
}
-// Convert a single hex nibble
+/* Convert a single hex nibble */
__inline__ static int
_from_hex(char c)
{
@@ -140,7 +142,7 @@
return ret;
}
-// Convert a character to lower case
+/* Convert a character to lower case */
__inline__ static char
_tolower(char c)
{
@@ -150,11 +152,7 @@
return c;
}
-
-
-//
-// Parse (scan) a number
-//
+/* Parse (scan) a number */
bool
parse_num(char *s, unsigned long *val, char **es, char *delim)
{
@@ -173,10 +171,10 @@
first = false;
c = *s++;
if (_is_hex(c) && ((digit = _from_hex(c)) < radix)) {
- // Valid digit
+ /* Valid digit */
#ifdef CYGPKG_HAL_MIPS
- // FIXME: tx49 compiler generates 0x2539018 for MUL which
- // isn't any good.
+ /* FIXME: tx49 compiler generates 0x2539018 for MUL which */
+ /* isn't any good. */
if (16 == radix)
result = result << 4;
else
@@ -187,12 +185,12 @@
#endif
} else {
if (delim != (char *)0) {
- // See if this character is one of the delimiters
+ /* See if this character is one of the delimiters */
char *dp = delim;
while (*dp && (c != *dp)) dp++;
- if (*dp) break; // Found a good delimiter
+ if (*dp) break; /* Found a good delimiter */
}
- return false; // Malformatted number
+ return false; /* Malformatted number */
}
}
*val = result;
@@ -207,11 +205,11 @@
#define USE_SPRINTF
#ifdef DEBUG
#ifndef USE_SPRINTF
-//
-// Note: this debug setup only works if the target platform has two serial ports
-// available so that the other one (currently only port 1) can be used for debug
-// messages.
-//
+/*
+ * Note: this debug setup only works if the target platform has two serial ports
+ * available so that the other one (currently only port 1) can be used for debug
+ * messages.
+ */
static int
zm_dprintf(char *fmt, ...)
{
@@ -235,9 +233,9 @@
}
#else
-//
-// Note: this debug setup works by storing the strings in a fixed buffer
-//
+/*
+ * Note: this debug setup works by storing the strings in a fixed buffer
+ */
#define FINAL
#ifdef FINAL
static char *zm_out = (char *)0x00380000;
@@ -308,7 +306,7 @@
#define ZM_DEBUG(x)
#endif
-// Wait for the line to go idle
+/* Wait for the line to go idle */
static void
xyzModem_flush(void)
{
@@ -330,7 +328,7 @@
unsigned short cksum;
ZM_DEBUG(zm_new());
- // Find the start of a header
+ /* Find the start of a header */
can_total = 0;
hdr_chars = 0;
@@ -356,11 +354,11 @@
if (++can_total == xyzModem_CAN_COUNT) {
return xyzModem_cancel;
} else {
- // Wait for multiple CAN to avoid early quits
+ /* Wait for multiple CAN to avoid early quits */
break;
}
case EOT:
- // EOT only supported if no noise
+ /* EOT only supported if no noise */
if (hdr_chars == 1) {
CYGACC_COMM_IF_PUTC(*xyz.__chan, ACK);
ZM_DEBUG(zm_dprintf("ACK on EOT #%d\n", __LINE__));
@@ -368,19 +366,19 @@
return xyzModem_eof;
}
default:
- // Ignore, waiting for start of header
+ /* Ignore, waiting for start of header */
;
}
} else {
- // Data stream timed out
- xyzModem_flush(); // Toss any current input
+ /* Data stream timed out */
+ xyzModem_flush(); /* Toss any current input */
ZM_DEBUG(zm_dump(__LINE__));
CYGACC_CALL_IF_DELAY_US((cyg_int32)250000);
return xyzModem_timeout;
}
}
- // Header found, now read the data
+ /* Header found, now read the data */
res = CYGACC_COMM_IF_GETC_TIMEOUT(*xyz.__chan, &xyz.blk);
ZM_DEBUG(zm_save(xyz.blk));
if (!res) {
@@ -420,18 +418,18 @@
}
}
ZM_DEBUG(zm_dump(__LINE__));
- // Validate the message
+ /* Validate the message */
if ((xyz.blk ^ xyz.cblk) != (unsigned char)0xFF) {
ZM_DEBUG(zm_dprintf("Framing error - blk: %x/%x/%x\n", xyz.blk, xyz.cblk, (xyz.blk ^ xyz.cblk)));
ZM_DEBUG(zm_dump_buf(xyz.pkt, xyz.len));
xyzModem_flush();
return xyzModem_frame;
}
- // Verify checksum/CRC
+ /* Verify checksum/CRC */
if (xyz.crc_mode) {
cksum = cyg_crc16(xyz.pkt, xyz.len);
if (cksum != ((xyz.crc1 << 8) | xyz.crc2)) {
- ZM_DEBUG(zm_dprintf("CRC error - recvd: %02x%02x, computed: %x\n",
+ ZM_DEBUG(zm_dprintf("CRC error - recvd: %02x%02x, computed: %x\n",
xyz.crc1, xyz.crc2, cksum & 0xFFFF));
return xyzModem_cksum;
}
@@ -445,18 +443,18 @@
return xyzModem_cksum;
}
}
- // If we get here, the message passes [structural] muster
+ /* If we get here, the message passes [structural] muster */
return 0;
}
-int
+int
xyzModem_stream_open(connection_info_t *info, int *err)
{
int console_chan, stat=0;
int retries = xyzModem_MAX_RETRIES;
int crc_retries = xyzModem_MAX_RETRIES_WITH_CRC;
-// ZM_DEBUG(zm_out = zm_out_start);
+/* ZM_DEBUG(zm_out = zm_out_start); */
#ifdef xyzModem_zmodem
if (info->mode == xyzModem_zmodem) {
*err = xyzModem_noZmodem;
@@ -465,7 +463,7 @@
#endif
#ifdef REDBOOT
- // Set up the I/O channel. Note: this allows for using a different port in the future
+ /* Set up the I/O channel. Note: this allows for using a different port in the future */
console_chan = CYGACC_CALL_IF_SET_CONSOLE_COMM(CYGNUM_CALL_IF_SET_COMM_ID_QUERY_CURRENT);
if (info->chan >= 0) {
CYGACC_CALL_IF_SET_CONSOLE_COMM(info->chan);
@@ -477,9 +475,9 @@
CYGACC_CALL_IF_SET_CONSOLE_COMM(console_chan);
CYGACC_COMM_IF_CONTROL(*xyz.__chan, __COMMCTL_SET_TIMEOUT, xyzModem_CHAR_TIMEOUT);
#else
-// TODO: CHECK !
+/* TODO: CHECK ! */
int dummy;
- xyz.__chan=&dummy;
+ xyz.__chan=&dummy;
#endif
xyz.len = 0;
xyz.crc_mode = true;
@@ -494,11 +492,11 @@
xyz.read_length = 0;
xyz.file_length = 0;
#endif
-
+
CYGACC_COMM_IF_PUTC(*xyz.__chan, (xyz.crc_mode ? 'C' : NAK));
if (xyz.mode == xyzModem_xmodem) {
- // X-modem doesn't have an information header - exit here
+ /* X-modem doesn't have an information header - exit here */
xyz.next_blk = 1;
return 0;
}
@@ -506,24 +504,24 @@
while (retries-- > 0) {
stat = xyzModem_get_hdr();
if (stat == 0) {
- // Y-modem file information header
+ /* Y-modem file information header */
if (xyz.blk == 0) {
#ifdef USE_YMODEM_LENGTH
- // skip filename
+ /* skip filename */
while (*xyz.bufp++);
- // get the length
+ /* get the length */
parse_num(xyz.bufp, &xyz.file_length, NULL, " ");
#endif
- // The rest of the file name data block quietly discarded
+ /* The rest of the file name data block quietly discarded */
xyz.tx_ack = true;
}
xyz.next_blk = 1;
xyz.len = 0;
return 0;
- } else
+ } else
if (stat == xyzModem_timeout) {
if (--crc_retries <= 0) xyz.crc_mode = false;
- CYGACC_CALL_IF_DELAY_US(5*100000); // Extra delay for startup
+ CYGACC_CALL_IF_DELAY_US(5*100000); /* Extra delay for startup */
CYGACC_COMM_IF_PUTC(*xyz.__chan, (xyz.crc_mode ? 'C' : NAK));
xyz.total_retries++;
ZM_DEBUG(zm_dprintf("NAK (%d)\n", __LINE__));
@@ -537,7 +535,7 @@
return -1;
}
-int
+int
xyzModem_stream_read(char *buf, int size, int *err)
{
int stat, total, len;
@@ -545,7 +543,7 @@
total = 0;
stat = xyzModem_cancel;
- // Try and get 'size' bytes into the buffer
+ /* Try and get 'size' bytes into the buffer */
while (!xyz.at_eof && (size > 0)) {
if (xyz.len == 0) {
retries = xyzModem_MAX_RETRIES;
@@ -562,8 +560,8 @@
#else
if (1) {
#endif
- // Data blocks can be padded with ^Z (EOF) characters
- // This code tries to detect and remove them
+ /* Data blocks can be padded with ^Z (EOF) characters */
+ /* This code tries to detect and remove them */
if ((xyz.bufp[xyz.len-1] == EOF) &&
(xyz.bufp[xyz.len-2] == EOF) &&
(xyz.bufp[xyz.len-3] == EOF)) {
@@ -574,10 +572,12 @@
}
#ifdef USE_YMODEM_LENGTH
- // See if accumulated length exceeds that of the file.
- // If so, reduce size (i.e., cut out pad bytes)
- // Only do this for Y-modem (and Z-modem should it ever
- // be supported since it can fall back to Y-modem mode).
+ /*
+ * See if accumulated length exceeds that of the file.
+ * If so, reduce size (i.e., cut out pad bytes)
+ * Only do this for Y-modem (and Z-modem should it ever
+ * be supported since it can fall back to Y-modem mode).
+ */
if (xyz.mode != xyzModem_xmodem && 0 != xyz.file_length) {
xyz.read_length += xyz.len;
if (xyz.read_length > xyz.file_length) {
@@ -587,9 +587,9 @@
#endif
break;
} else if (xyz.blk == ((xyz.next_blk - 1) & 0xFF)) {
- // Just re-ACK this so sender will get on with it
+ /* Just re-ACK this so sender will get on with it */
CYGACC_COMM_IF_PUTC(*xyz.__chan, ACK);
- continue; // Need new header
+ continue; /* Need new header */
} else {
stat = xyzModem_sequence;
}
@@ -604,7 +604,7 @@
CYGACC_COMM_IF_PUTC(*xyz.__chan, (xyz.crc_mode ? 'C' : NAK));
xyz.total_retries++;
ZM_DEBUG(zm_dprintf("Reading Final Header\n"));
- stat = xyzModem_get_hdr();
+ stat = xyzModem_get_hdr();
CYGACC_COMM_IF_PUTC(*xyz.__chan, ACK);
ZM_DEBUG(zm_dprintf("FINAL ACK (%d)\n", __LINE__));
}
@@ -621,7 +621,7 @@
return total;
}
}
- // Don't "read" data from the EOF protocol package
+ /* Don't "read" data from the EOF protocol package */
if (!xyz.at_eof) {
len = xyz.len;
if (size < len) len = size;
@@ -639,15 +639,15 @@
void
xyzModem_stream_close(int *err)
{
- diag_printf("xyzModem - %s mode, %d(SOH)/%d(STX)/%d(CAN) packets, %d retries\n",
+ diag_printf("xyzModem - %s mode, %d(SOH)/%d(STX)/%d(CAN) packets, %d retries\n",
xyz.crc_mode ? "CRC" : "Cksum",
xyz.total_SOH, xyz.total_STX, xyz.total_CAN,
xyz.total_retries);
ZM_DEBUG(zm_flush());
}
-// Need to be able to clean out the input buffer, so have to take the
-// getc
+/* Need to be able to clean out the input buffer, so have to take the */
+/* getc */
void xyzModem_stream_terminate(bool abort, int (*getc)(void))
{
int c;
@@ -657,8 +657,8 @@
switch (xyz.mode) {
case xyzModem_xmodem:
case xyzModem_ymodem:
- // The X/YMODEM Spec seems to suggest that multiple CAN followed by an equal
- // number of Backspaces is a friendly way to get the other end to abort.
+ /* The X/YMODEM Spec seems to suggest that multiple CAN followed by an equal */
+ /* number of Backspaces is a friendly way to get the other end to abort. */
CYGACC_COMM_IF_PUTC(*xyz.__chan,CAN);
CYGACC_COMM_IF_PUTC(*xyz.__chan,CAN);
CYGACC_COMM_IF_PUTC(*xyz.__chan,CAN);
@@ -667,29 +667,33 @@
CYGACC_COMM_IF_PUTC(*xyz.__chan,BSP);
CYGACC_COMM_IF_PUTC(*xyz.__chan,BSP);
CYGACC_COMM_IF_PUTC(*xyz.__chan,BSP);
- // Now consume the rest of what's waiting on the line.
+ /* Now consume the rest of what's waiting on the line. */
ZM_DEBUG(zm_dprintf("Flushing serial line.\n"));
xyzModem_flush();
xyz.at_eof = true;
break;
#ifdef xyzModem_zmodem
case xyzModem_zmodem:
- // Might support it some day I suppose.
+ /* Might support it some day I suppose. */
#endif
break;
}
} else {
ZM_DEBUG(zm_dprintf("Engaging cleanup mode...\n"));
- // Consume any trailing crap left in the inbuffer from
- // previous recieved blocks. Since very few files are an exact multiple
- // of the transfer block size, there will almost always be some gunk here.
- // If we don't eat it now, RedBoot will think the user typed it.
+ /*
+ * Consume any trailing crap left in the inbuffer from
+ * previous recieved blocks. Since very few files are an exact multiple
+ * of the transfer block size, there will almost always be some gunk here.
+ * If we don't eat it now, RedBoot will think the user typed it.
+ */
ZM_DEBUG(zm_dprintf("Trailing gunk:\n"));
while ((c = (*getc)()) > -1) ;
ZM_DEBUG(zm_dprintf("\n"));
- // Make a small delay to give terminal programs like minicom
- // time to get control again after their file transfer program
- // exits.
+ /*
+ * Make a small delay to give terminal programs like minicom
+ * time to get control again after their file transfer program
+ * exits.
+ */
CYGACC_CALL_IF_DELAY_US((cyg_int32)250000);
}
}
@@ -728,12 +732,12 @@
}
}
-//
-// RedBoot interface
-//
-#if 0 // SB
+/*
+ * RedBoot interface
+ */
+#if 0 /* SB */
GETC_IO_FUNCS(xyzModem_io, xyzModem_stream_open, xyzModem_stream_close,
xyzModem_stream_terminate, xyzModem_stream_read, xyzModem_error);
RedBoot_load(xmodem, xyzModem_io, false, false, xyzModem_xmodem);
RedBoot_load(ymodem, xyzModem_io, false, false, xyzModem_ymodem);
-#endif
+#endif
diff --git a/cpu/mpc5xxx/cpu.c b/cpu/mpc5xxx/cpu.c
index 5ad4baa..6b6f828 100644
--- a/cpu/mpc5xxx/cpu.c
+++ b/cpu/mpc5xxx/cpu.c
@@ -58,7 +58,7 @@
break;
}
- printf (" v%d.%d, Core v%d.%d", SVR_MJREV (svr), SVR_MNREV (svr),
+ printf (" v%d.%d, Core v%d.%d", SVR_MJREV (svr), SVR_MNREV (svr),
PVR_MAJ(pvr), PVR_MIN(pvr));
#endif
printf (" at %s MHz\n", strmhz (buf, clock));
diff --git a/cpu/mpc83xx/cpu.c b/cpu/mpc83xx/cpu.c
index 7ca1ceb..20bba6c 100644
--- a/cpu/mpc83xx/cpu.c
+++ b/cpu/mpc83xx/cpu.c
@@ -260,7 +260,7 @@
dmamr0 = (DMA_CHANNEL_TRANSFER_MODE_DIRECT |
DMA_CHANNEL_SOURCE_ADDRESS_HOLD_8B |
DMA_CHANNEL_SOURCE_ADRESSS_HOLD_EN);
-
+
dma->dmamr0 = swab32(dmamr0);
__asm__ __volatile__ ("sync");
diff --git a/cpu/mpc83xx/spd_sdram.c b/cpu/mpc83xx/spd_sdram.c
index b4012a8..48624fe 100644
--- a/cpu/mpc83xx/spd_sdram.c
+++ b/cpu/mpc83xx/spd_sdram.c
@@ -1,7 +1,7 @@
/*
* (C) Copyright 2006
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
+ *
* Copyright 2004 Freescale Semiconductor.
* (C) Copyright 2003 Motorola Inc.
* Xianghua Xiao (X.Xiao@motorola.com)
@@ -426,7 +426,7 @@
/*
* Initialize all of memory for ECC, then enable errors.
*/
-//#define CONFIG_DDR_ECC_INIT_VIA_DMA
+/* #define CONFIG_DDR_ECC_INIT_VIA_DMA */
void ddr_enable_ecc(unsigned int dram_size)
{
uint *p;
diff --git a/cpu/ppc4xx/sdram.c b/cpu/ppc4xx/sdram.c
index c5ab017..e31d59d 100644
--- a/cpu/ppc4xx/sdram.c
+++ b/cpu/ppc4xx/sdram.c
@@ -18,7 +18,7 @@
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
@@ -38,17 +38,17 @@
#ifndef CFG_SDRAM_TABLE
sdram_conf_t mb0cf[] = {
- {(128 << 20), 13, 0x000A4001}, /* (0-128MB) Address Mode 3, 13x10(4) */
- {(64 << 20), 13, 0x00084001}, /* (0-64MB) Address Mode 3, 13x9(4) */
- {(32 << 20), 12, 0x00062001}, /* (0-32MB) Address Mode 2, 12x9(4) */
- {(16 << 20), 12, 0x00046001}, /* (0-16MB) Address Mode 4, 12x8(4) */
- {(4 << 20), 11, 0x00008001}, /* (0-4MB) Address Mode 5, 11x8(2) */
+ {(128 << 20), 13, 0x000A4001}, /* (0-128MB) Address Mode 3, 13x10(4) */
+ {(64 << 20), 13, 0x00084001}, /* (0-64MB) Address Mode 3, 13x9(4) */
+ {(32 << 20), 12, 0x00062001}, /* (0-32MB) Address Mode 2, 12x9(4) */
+ {(16 << 20), 12, 0x00046001}, /* (0-16MB) Address Mode 4, 12x8(4) */
+ {(4 << 20), 11, 0x00008001}, /* (0-4MB) Address Mode 5, 11x8(2) */
};
#else
sdram_conf_t mb0cf[] = CFG_SDRAM_TABLE;
#endif
-#define N_MB0CF (sizeof(mb0cf) / sizeof(mb0cf[0]))
+#define N_MB0CF (sizeof(mb0cf) / sizeof(mb0cf[0]))
#ifndef CONFIG_440
@@ -65,76 +65,76 @@
static ulong compute_sdtr1(ulong speed)
{
#ifdef CFG_SDRAM_CASL
- ulong tmp;
- ulong sdtr1 = 0;
+ ulong tmp;
+ ulong sdtr1 = 0;
- /* CASL */
- if (CFG_SDRAM_CASL < 2)
- sdtr1 |= (1 << SDRAM0_TR_CASL);
- else
- if (CFG_SDRAM_CASL > 4)
- sdtr1 |= (3 << SDRAM0_TR_CASL);
- else
- sdtr1 |= ((CFG_SDRAM_CASL-1) << SDRAM0_TR_CASL);
+ /* CASL */
+ if (CFG_SDRAM_CASL < 2)
+ sdtr1 |= (1 << SDRAM0_TR_CASL);
+ else
+ if (CFG_SDRAM_CASL > 4)
+ sdtr1 |= (3 << SDRAM0_TR_CASL);
+ else
+ sdtr1 |= ((CFG_SDRAM_CASL-1) << SDRAM0_TR_CASL);
- /* PTA */
- tmp = ns2clks(CFG_SDRAM_PTA);
- if ((tmp >= 2) && (tmp <= 4))
- sdtr1 |= ((tmp-1) << SDRAM0_TR_PTA);
- else
- sdtr1 |= ((4-1) << SDRAM0_TR_PTA);
+ /* PTA */
+ tmp = ns2clks(CFG_SDRAM_PTA);
+ if ((tmp >= 2) && (tmp <= 4))
+ sdtr1 |= ((tmp-1) << SDRAM0_TR_PTA);
+ else
+ sdtr1 |= ((4-1) << SDRAM0_TR_PTA);
- /* CTP */
- tmp = ns2clks(CFG_SDRAM_CTP);
- if ((tmp >= 2) && (tmp <= 4))
- sdtr1 |= ((tmp-1) << SDRAM0_TR_CTP);
- else
- sdtr1 |= ((4-1) << SDRAM0_TR_CTP);
+ /* CTP */
+ tmp = ns2clks(CFG_SDRAM_CTP);
+ if ((tmp >= 2) && (tmp <= 4))
+ sdtr1 |= ((tmp-1) << SDRAM0_TR_CTP);
+ else
+ sdtr1 |= ((4-1) << SDRAM0_TR_CTP);
- /* LDF */
- tmp = ns2clks(CFG_SDRAM_LDF);
- if ((tmp >= 2) && (tmp <= 4))
- sdtr1 |= ((tmp-1) << SDRAM0_TR_LDF);
- else
- sdtr1 |= ((2-1) << SDRAM0_TR_LDF);
+ /* LDF */
+ tmp = ns2clks(CFG_SDRAM_LDF);
+ if ((tmp >= 2) && (tmp <= 4))
+ sdtr1 |= ((tmp-1) << SDRAM0_TR_LDF);
+ else
+ sdtr1 |= ((2-1) << SDRAM0_TR_LDF);
- /* RFTA */
- tmp = ns2clks(CFG_SDRAM_RFTA);
- if ((tmp >= 4) && (tmp <= 10))
- sdtr1 |= ((tmp-4) << SDRAM0_TR_RFTA);
- else
- sdtr1 |= ((10-4) << SDRAM0_TR_RFTA);
+ /* RFTA */
+ tmp = ns2clks(CFG_SDRAM_RFTA);
+ if ((tmp >= 4) && (tmp <= 10))
+ sdtr1 |= ((tmp-4) << SDRAM0_TR_RFTA);
+ else
+ sdtr1 |= ((10-4) << SDRAM0_TR_RFTA);
- /* RCD */
- tmp = ns2clks(CFG_SDRAM_RCD);
- if ((tmp >= 2) && (tmp <= 4))
- sdtr1 |= ((tmp-1) << SDRAM0_TR_RCD);
- else
- sdtr1 |= ((4-1) << SDRAM0_TR_RCD);
+ /* RCD */
+ tmp = ns2clks(CFG_SDRAM_RCD);
+ if ((tmp >= 2) && (tmp <= 4))
+ sdtr1 |= ((tmp-1) << SDRAM0_TR_RCD);
+ else
+ sdtr1 |= ((4-1) << SDRAM0_TR_RCD);
- return sdtr1;
+ return sdtr1;
#else /* CFG_SDRAM_CASL */
- /*
- * If no values are configured in the board config file
- * use the default values, which seem to be ok for most
- * boards.
- *
- * REMARK:
- * For new board ports we strongly recommend to define the
- * correct values for the used SDRAM chips in your board
- * config file (see PPChameleonEVB.h)
- */
- if (speed > 100000000) {
- /*
- * 133 MHz SDRAM
- */
- return 0x01074015;
- } else {
- /*
- * default: 100 MHz SDRAM
- */
- return 0x0086400d;
- }
+ /*
+ * If no values are configured in the board config file
+ * use the default values, which seem to be ok for most
+ * boards.
+ *
+ * REMARK:
+ * For new board ports we strongly recommend to define the
+ * correct values for the used SDRAM chips in your board
+ * config file (see PPChameleonEVB.h)
+ */
+ if (speed > 100000000) {
+ /*
+ * 133 MHz SDRAM
+ */
+ return 0x01074015;
+ } else {
+ /*
+ * default: 100 MHz SDRAM
+ */
+ return 0x0086400d;
+ }
#endif /* CFG_SDRAM_CASL */
}
@@ -142,24 +142,24 @@
static ulong compute_rtr(ulong speed, ulong rows, ulong refresh)
{
#ifdef CFG_SDRAM_CASL
- ulong tmp;
+ ulong tmp;
- tmp = ((refresh*1000*1000) / (1 << rows)) * (speed / 1000);
- tmp /= 1000000;
+ tmp = ((refresh*1000*1000) / (1 << rows)) * (speed / 1000);
+ tmp /= 1000000;
- return ((tmp & 0x00003FF8) << 16);
+ return ((tmp & 0x00003FF8) << 16);
#else /* CFG_SDRAM_CASL */
- if (speed > 100000000) {
- /*
- * 133 MHz SDRAM
- */
+ if (speed > 100000000) {
+ /*
+ * 133 MHz SDRAM
+ */
return 0x07f00000;
- } else {
- /*
- * default: 100 MHz SDRAM
- */
+ } else {
+ /*
+ * default: 100 MHz SDRAM
+ */
return 0x05f00000;
- }
+ }
#endif /* CFG_SDRAM_CASL */
}
@@ -172,19 +172,19 @@
ulong sdtr1;
int i;
- /*
- * Determine SDRAM speed
- */
- speed = get_bus_freq(0); /* parameter not used on ppc4xx */
+ /*
+ * Determine SDRAM speed
+ */
+ speed = get_bus_freq(0); /* parameter not used on ppc4xx */
- /*
- * sdtr1 (register SDRAM0_TR) must take into account timings listed
- * in SDRAM chip datasheet. rtr (register SDRAM0_RTR) must take into
- * account actual SDRAM size. So we can set up sdtr1 according to what
- * is specified in board configuration file while rtr dependds on SDRAM
- * size we are assuming before detection.
- */
- sdtr1 = compute_sdtr1(speed);
+ /*
+ * sdtr1 (register SDRAM0_TR) must take into account timings listed
+ * in SDRAM chip datasheet. rtr (register SDRAM0_RTR) must take into
+ * account actual SDRAM size. So we can set up sdtr1 according to what
+ * is specified in board configuration file while rtr dependds on SDRAM
+ * size we are assuming before detection.
+ */
+ sdtr1 = compute_sdtr1(speed);
for (i=0; i<N_MB0CF; i++) {
/*
@@ -343,8 +343,8 @@
* Autodetect onboard DDR SDRAM on 440 platforms
*
* NOTE: Some of the hardcoded values are hardware dependant,
- * so this should be extended for other future boards
- * using this routine!
+ * so this should be extended for other future boards
+ * using this routine!
*/
long int initdram(int board_type)
{
@@ -360,11 +360,11 @@
/*
* Setup some default
*/
- mtsdram(mem_uabba, 0x00000000); /* ubba=0 (default) */
- mtsdram(mem_slio, 0x00000000); /* rdre=0 wrre=0 rarw=0 */
+ mtsdram(mem_uabba, 0x00000000); /* ubba=0 (default) */
+ mtsdram(mem_slio, 0x00000000); /* rdre=0 wrre=0 rarw=0 */
mtsdram(mem_devopt, 0x00000000); /* dll=0 ds=0 (normal) */
mtsdram(mem_wddctr, 0x00000000); /* wrcp=0 dcd=0 */
- mtsdram(mem_clktr, 0x40000000); /* clkp=1 (90 deg wr) dcdt=0 */
+ mtsdram(mem_clktr, 0x40000000); /* clkp=1 (90 deg wr) dcdt=0 */
/*
* Following for CAS Latency = 2.5 @ 133 MHz PLB
@@ -379,7 +379,7 @@
/*
* Enable the controller, then wait for DCEN to complete
*/
- mtsdram(mem_cfg0, 0x86000000); /* DCEN=1, PMUD=1, 64-bit */
+ mtsdram(mem_cfg0, 0x86000000); /* DCEN=1, PMUD=1, 64-bit */
udelay(10000);
if (get_ram_size(0, mb0cf[i].size) == mb0cf[i].size) {
diff --git a/doc/README.mpc8349emds.ddrecc b/doc/README.mpc8349emds.ddrecc
index 401c0b6..eb249c3 100644
--- a/doc/README.mpc8349emds.ddrecc
+++ b/doc/README.mpc8349emds.ddrecc
@@ -152,5 +152,3 @@
reached Single-Bit Error Threshold. Multiple Memory Errors bit is also 'on', that
is Counter reached Threshold more than one time (it wraps back after reaching
Threshold).
-
-
diff --git a/include/configs/MPC8349EMDS.h b/include/configs/MPC8349EMDS.h
index 39e3d95..1a47980 100644
--- a/include/configs/MPC8349EMDS.h
+++ b/include/configs/MPC8349EMDS.h
@@ -75,13 +75,13 @@
/*
* 32-bit data path mode.
- *
+ *
* Please note that using this mode for devices with the real density of 64-bit
* effectively reduces the amount of available memory due to the effect of
* wrapping around while translating address to row/columns, for example in the
* 256MB module the upper 128MB get aliased with contents of the lower
* 128MB); normally this define should be used for devices with real 32-bit
- * data path.
+ * data path.
*/
#undef CONFIG_DDR_32BIT
diff --git a/include/crc.h b/include/crc.h
index 63399bf..10560c9 100644
--- a/include/crc.h
+++ b/include/crc.h
@@ -1,56 +1,58 @@
-//==========================================================================
-//
-// crc.h
-//
-// Interface for the CRC algorithms.
-//
-//==========================================================================
-//####ECOSGPLCOPYRIGHTBEGIN####
-// -------------------------------------------
-// This file is part of eCos, the Embedded Configurable Operating System.
-// Copyright (C) 2002 Andrew Lunn
-//
-// eCos is free software; you can redistribute it and/or modify it under
-// the terms of the GNU General Public License as published by the Free
-// Software Foundation; either version 2 or (at your option) any later version.
-//
-// eCos is distributed in the hope that it will be useful, but WITHOUT ANY
-// WARRANTY; without even the implied warranty of MERCHANTABILITY or
-// FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
-// for more details.
-//
-// You should have received a copy of the GNU General Public License along
-// with eCos; if not, write to the Free Software Foundation, Inc.,
-// 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA.
-//
-// As a special exception, if other files instantiate templates or use macros
-// or inline functions from this file, or you compile this file and link it
-// with other works to produce a work based on this file, this file does not
-// by itself cause the resulting work to be covered by the GNU General Public
-// License. However the source code for this file must still be made available
-// in accordance with section (3) of the GNU General Public License.
-//
-// This exception does not invalidate any other reasons why a work based on
-// this file might be covered by the GNU General Public License.
-//
-// Alternative licenses for eCos may be arranged by contacting Red Hat, Inc.
-// at http://sources.redhat.com/ecos/ecos-license/
-// -------------------------------------------
-//####ECOSGPLCOPYRIGHTEND####
-//==========================================================================
-//#####DESCRIPTIONBEGIN####
-//
-// Author(s): Andrew Lunn
-// Contributors: Andrew Lunn
-// Date: 2002-08-06
-// Purpose:
-// Description:
-//
-// This code is part of eCos (tm).
-//
-//####DESCRIPTIONEND####
-//
-//==========================================================================
+/*
+ *==========================================================================
+ *
+ * crc.h
+ *
+ * Interface for the CRC algorithms.
+ *
+ *==========================================================================
+ *####ECOSGPLCOPYRIGHTBEGIN####
+ * -------------------------------------------
+ * This file is part of eCos, the Embedded Configurable Operating System.
+ * Copyright (C) 2002 Andrew Lunn
+ *
+ * eCos is free software; you can redistribute it and/or modify it under
+ * the terms of the GNU General Public License as published by the Free
+ * Software Foundation; either version 2 or (at your option) any later version.
+ *
+ * eCos is distributed in the hope that it will be useful, but WITHOUT ANY
+ * WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
+ * for more details.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with eCos; if not, write to the Free Software Foundation, Inc.,
+ * 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA.
+ *
+ * As a special exception, if other files instantiate templates or use macros
+ * or inline functions from this file, or you compile this file and link it
+ * with other works to produce a work based on this file, this file does not
+ * by itself cause the resulting work to be covered by the GNU General Public
+ * License. However the source code for this file must still be made available
+ * in accordance with section (3) of the GNU General Public License.
+ *
+ * This exception does not invalidate any other reasons why a work based on
+ * this file might be covered by the GNU General Public License.
+ *
+ * Alternative licenses for eCos may be arranged by contacting Red Hat, Inc.
+ * at http: *sources.redhat.com/ecos/ecos-license/
+ * -------------------------------------------
+ *####ECOSGPLCOPYRIGHTEND####
+ *==========================================================================
+ *#####DESCRIPTIONBEGIN####
+ *
+ * Author(s): Andrew Lunn
+ * Contributors: Andrew Lunn
+ * Date: 2002-08-06
+ * Purpose:
+ * Description:
+ *
+ * This code is part of eCos (tm).
+ *
+ *####DESCRIPTIONEND####
+ *
+ *==========================================================================
+ */
#ifndef _SERVICES_CRC_CRC_H_
#define _SERVICES_CRC_CRC_H_
@@ -65,37 +67,34 @@
# endif
#endif
-// Compute a CRC, using the POSIX 1003 definition
-extern uint32_t
+/* Compute a CRC, using the POSIX 1003 definition */
+extern uint32_t
cyg_posix_crc32(unsigned char *s, int len);
-// Gary S. Brown's 32 bit CRC
+/* Gary S. Brown's 32 bit CRC */
-extern uint32_t
+extern uint32_t
cyg_crc32(unsigned char *s, int len);
-// Gary S. Brown's 32 bit CRC, but accumulate the result from a
-// previous CRC calculation
+/* Gary S. Brown's 32 bit CRC, but accumulate the result from a */
+/* previous CRC calculation */
-extern uint32_t
+extern uint32_t
cyg_crc32_accumulate(uint32_t crc, unsigned char *s, int len);
-// Ethernet FCS Algorithm
+/* Ethernet FCS Algorithm */
-extern uint32_t
+extern uint32_t
cyg_ether_crc32(unsigned char *s, int len);
-// Ethernet FCS algorithm, but accumulate the result from a previous
-// CRC calculation.
+/* Ethernet FCS algorithm, but accumulate the result from a previous */
+/* CRC calculation. */
-extern uint32_t
+extern uint32_t
cyg_ether_crc32_accumulate(uint32_t crc, unsigned char *s, int len);
-// 16 bit CRC with polynomial x^16+x^12+x^5+1
+/* 16 bit CRC with polynomial x^16+x^12+x^5+1 */
extern uint16_t cyg_crc16(unsigned char *s, int len);
-#endif // _SERVICES_CRC_CRC_H_
-
-
-
+#endif /* _SERVICES_CRC_CRC_H_ */
diff --git a/include/xyzModem.h b/include/xyzModem.h
index a62a174..4ec10b5 100644
--- a/include/xyzModem.h
+++ b/include/xyzModem.h
@@ -1,65 +1,67 @@
-//==========================================================================
-//
-// xyzModem.h
-//
-// RedBoot stream handler for xyzModem protocol
-//
-//==========================================================================
-//####ECOSGPLCOPYRIGHTBEGIN####
-// -------------------------------------------
-// This file is part of eCos, the Embedded Configurable Operating System.
-// Copyright (C) 1998, 1999, 2000, 2001, 2002 Red Hat, Inc.
-// Copyright (C) 2002 Gary Thomas
-//
-// eCos is free software; you can redistribute it and/or modify it under
-// the terms of the GNU General Public License as published by the Free
-// Software Foundation; either version 2 or (at your option) any later version.
-//
-// eCos is distributed in the hope that it will be useful, but WITHOUT ANY
-// WARRANTY; without even the implied warranty of MERCHANTABILITY or
-// FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
-// for more details.
-//
-// You should have received a copy of the GNU General Public License along
-// with eCos; if not, write to the Free Software Foundation, Inc.,
-// 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA.
-//
-// As a special exception, if other files instantiate templates or use macros
-// or inline functions from this file, or you compile this file and link it
-// with other works to produce a work based on this file, this file does not
-// by itself cause the resulting work to be covered by the GNU General Public
-// License. However the source code for this file must still be made available
-// in accordance with section (3) of the GNU General Public License.
-//
-// This exception does not invalidate any other reasons why a work based on
-// this file might be covered by the GNU General Public License.
-//
-// Alternative licenses for eCos may be arranged by contacting Red Hat, Inc.
-// at http://sources.redhat.com/ecos/ecos-license/
-// -------------------------------------------
-//####ECOSGPLCOPYRIGHTEND####
-//==========================================================================
-//#####DESCRIPTIONBEGIN####
-//
-// Author(s): gthomas
-// Contributors: gthomas
-// Date: 2000-07-14
-// Purpose:
-// Description:
-//
-// This code is part of RedBoot (tm).
-//
-//####DESCRIPTIONEND####
-//
-//==========================================================================
+/*
+ *==========================================================================
+ *
+ * xyzModem.h
+ *
+ * RedBoot stream handler for xyzModem protocol
+ *
+ *==========================================================================
+ *####ECOSGPLCOPYRIGHTBEGIN####
+ * -------------------------------------------
+ * This file is part of eCos, the Embedded Configurable Operating System.
+ * Copyright (C) 1998, 1999, 2000, 2001, 2002 Red Hat, Inc.
+ * Copyright (C) 2002 Gary Thomas
+ *
+ * eCos is free software; you can redistribute it and/or modify it under
+ * the terms of the GNU General Public License as published by the Free
+ * Software Foundation; either version 2 or (at your option) any later version.
+ *
+ * eCos is distributed in the hope that it will be useful, but WITHOUT ANY
+ * WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
+ * for more details.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with eCos; if not, write to the Free Software Foundation, Inc.,
+ * 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA.
+ *
+ * As a special exception, if other files instantiate templates or use macros
+ * or inline functions from this file, or you compile this file and link it
+ * with other works to produce a work based on this file, this file does not
+ * by itself cause the resulting work to be covered by the GNU General Public
+ * License. However the source code for this file must still be made available
+ * in accordance with section (3) of the GNU General Public License.
+ *
+ * This exception does not invalidate any other reasons why a work based on
+ * this file might be covered by the GNU General Public License.
+ *
+ * Alternative licenses for eCos may be arranged by contacting Red Hat, Inc.
+ * at http: *sources.redhat.com/ecos/ecos-license/
+ * -------------------------------------------
+ *####ECOSGPLCOPYRIGHTEND####
+ *==========================================================================
+ *#####DESCRIPTIONBEGIN####
+ *
+ * Author(s): gthomas
+ * Contributors: gthomas
+ * Date: 2000-07-14
+ * Purpose:
+ * Description:
+ *
+ * This code is part of RedBoot (tm).
+ *
+ *####DESCRIPTIONEND####
+ *
+ *==========================================================================
+ */
#ifndef _XYZMODEM_H_
#define _XYZMODEM_H_
#define xyzModem_xmodem 1
#define xyzModem_ymodem 2
-// Don't define this until the protocol support is in place
-//#define xyzModem_zmodem 3
+/* Don't define this until the protocol support is in place */
+/*#define xyzModem_zmodem 3 */
#define xyzModem_access -1
#define xyzModem_noZmodem -2
@@ -103,10 +105,10 @@
#endif
-int xyzModem_stream_open(connection_info_t *info, int *err);
-void xyzModem_stream_close(int *err);
-void xyzModem_stream_terminate(bool method, int (*getc)(void));
-int xyzModem_stream_read(char *buf, int size, int *err);
+int xyzModem_stream_open(connection_info_t *info, int *err);
+void xyzModem_stream_close(int *err);
+void xyzModem_stream_terminate(bool method, int (*getc)(void));
+int xyzModem_stream_read(char *buf, int size, int *err);
char *xyzModem_error(int err);
-#endif // _XYZMODEM_H_
+#endif /* _XYZMODEM_H_ */
diff --git a/rtc/ds1374.c b/rtc/ds1374.c
index 31f06e5..50a996c 100644
--- a/rtc/ds1374.c
+++ b/rtc/ds1374.c
@@ -116,7 +116,7 @@
/*
* Since the reads are being performed one byte at a time,
- * there is a chance that a carry will occur during the read.
+ * there is a chance that a carry will occur during the read.
* To detect this, 2 reads are performed and compared.
*/
limit = 10;