* The PS/2 mux on the BMS2003 board needs 450 ms after power on
before we can access it; add delay in case we are faster (with no
CF card inserted)
* Cleanup of some init functions
* Make sure SCC Ethernet is always stopped by the time we boot Linux
to avoid Linux crashes by early packets coming in.
* Accelerate flash accesses on LWMON board by using buffered writes
diff --git a/CHANGELOG b/CHANGELOG
index b136f21..6560859 100644
--- a/CHANGELOG
+++ b/CHANGELOG
@@ -2,6 +2,17 @@
Changes since U-Boot 1.0.1:
======================================================================
+* The PS/2 mux on the BMS2003 board needs 450 ms after power on
+ before we can access it; add delay in case we are faster (with no
+ CF card inserted)
+
+* Cleanup of some init functions
+
+* Make sure SCC Ethernet is always stopped by the time we boot Linux
+ to avoid Linux crashes by early packets coming in.
+
+* Accelerate flash accesses on LWMON board by using buffered writes
+
* Fix typo in Makefile;
fix problem with PARTNUM detection
diff --git a/board/LEOX/elpt860/elpt860.c b/board/LEOX/elpt860/elpt860.c
index c8bc41a..82a831f 100644
--- a/board/LEOX/elpt860/elpt860.c
+++ b/board/LEOX/elpt860/elpt860.c
@@ -33,7 +33,7 @@
/*
** Note 1: In this file, you have to provide the following functions:
** ------
-** int board_pre_init(void)
+** int board_early_init_f(void)
** int checkboard(void)
** long int initdram(int board_type)
** called from 'board_init_f()' into 'common/board.c'
@@ -145,7 +145,7 @@
/*
* Very early board init code (fpga boot, etc.)
*/
-int board_pre_init (void)
+int board_early_init_f (void)
{
volatile immap_t *immr = (immap_t *) CFG_IMMR;
diff --git a/board/MAI/AmigaOneG3SE/articiaS.c b/board/MAI/AmigaOneG3SE/articiaS.c
index 9fd6b95..a4dad64 100644
--- a/board/MAI/AmigaOneG3SE/articiaS.c
+++ b/board/MAI/AmigaOneG3SE/articiaS.c
@@ -675,7 +675,7 @@
asm volatile ("mtmsr %0"::"r" (msr));
}
-int board_pre_init (void)
+int board_early_init_f (void)
{
unsigned char c_value = 0;
unsigned long msr;
diff --git a/board/Marvell/common/bootseq.txt b/board/Marvell/common/bootseq.txt
index 648c2ff..391d49a 100644
--- a/board/Marvell/common/bootseq.txt
+++ b/board/Marvell/common/bootseq.txt
@@ -58,7 +58,7 @@
call cpu_init_f
debug leds
board_init_f: (common/board.c)
- board_pre_init:
+ board_early_init_f:
remap gt regs?
map PCI mem/io
map device space
diff --git a/board/Marvell/db64360/db64360.c b/board/Marvell/db64360/db64360.c
index 438700a..7cadafd 100644
--- a/board/Marvell/db64360/db64360.c
+++ b/board/Marvell/db64360/db64360.c
@@ -61,7 +61,7 @@
/* Unfortunately, we cant change it while we are in flash, so we initialize it
* to the "final" value. This means that any debug_led calls before
- * board_pre_init wont work right (like in cpu_init_f).
+ * board_early_init_f wont work right (like in cpu_init_f).
* See also my_remap_gt_regs below. (NTL)
*/
@@ -237,11 +237,11 @@
}
/*
- * board_pre_init.
+ * board_early_init_f.
*
* set up gal. device mappings, etc.
*/
-int board_pre_init (void)
+int board_early_init_f (void)
{
uchar sram_boot = 0;
diff --git a/board/Marvell/db64460/db64460.c b/board/Marvell/db64460/db64460.c
index 572dc47..85b2331 100644
--- a/board/Marvell/db64460/db64460.c
+++ b/board/Marvell/db64460/db64460.c
@@ -61,7 +61,7 @@
/* Unfortunately, we cant change it while we are in flash, so we initialize it
* to the "final" value. This means that any debug_led calls before
- * board_pre_init wont work right (like in cpu_init_f).
+ * board_early_init_f wont work right (like in cpu_init_f).
* See also my_remap_gt_regs below. (NTL)
*/
@@ -237,11 +237,11 @@
}
/*
- * board_pre_init.
+ * board_early_init_f.
*
* set up gal. device mappings, etc.
*/
-int board_pre_init (void)
+int board_early_init_f (void)
{
uchar sram_boot = 0;
diff --git a/board/altera/dk1c20/dk1c20.c b/board/altera/dk1c20/dk1c20.c
index 96f1ece..3954486 100644
--- a/board/altera/dk1c20/dk1c20.c
+++ b/board/altera/dk1c20/dk1c20.c
@@ -31,7 +31,7 @@
printf ("default_hdlr\n");
}
-int board_pre_init (void)
+int board_early_init_f (void)
{
/* init seven segment led display and switch off */
sevenseg_set(SEVENSEG_OFF);
diff --git a/board/altera/dk1s10/dk1s10.c b/board/altera/dk1s10/dk1s10.c
index 6d7be2d..832a0b9 100644
--- a/board/altera/dk1s10/dk1s10.c
+++ b/board/altera/dk1s10/dk1s10.c
@@ -31,7 +31,7 @@
printf ("default_hdlr\n");
}
-int board_pre_init (void)
+int board_early_init_f (void)
{
/* init seven segment led display and switch off */
sevenseg_set(SEVENSEG_OFF);
diff --git a/board/bubinga405ep/bubinga405ep.c b/board/bubinga405ep/bubinga405ep.c
index f73b166..0be7965 100644
--- a/board/bubinga405ep/bubinga405ep.c
+++ b/board/bubinga405ep/bubinga405ep.c
@@ -26,7 +26,7 @@
#include <asm/processor.h>
-int board_pre_init (void)
+int board_early_init_f (void)
{
mtdcr (uicsr, 0xFFFFFFFF); /* clear all ints */
mtdcr (uicer, 0x00000000); /* disable all ints */
diff --git a/board/cpc45/cpc45.c b/board/cpc45/cpc45.c
index 455cc12..f44a59d 100644
--- a/board/cpc45/cpc45.c
+++ b/board/cpc45/cpc45.c
@@ -32,7 +32,7 @@
/* We have to clear the initial data area here. Couldn't have done it
* earlier because DRAM had not been initialized.
*/
-int board_pre_init(void)
+int board_early_init_f(void)
{
/* enable DUAL UART Mode on CPC45 */
diff --git a/board/cradle/cradle.c b/board/cradle/cradle.c
index f599a31..f5c99b1 100644
--- a/board/cradle/cradle.c
+++ b/board/cradle/cradle.c
@@ -170,7 +170,7 @@
int
/**********************************************************/
-board_post_init (void)
+board_late_init (void)
/**********************************************************/
{
return (0);
diff --git a/board/cray/L1/L1.c b/board/cray/L1/L1.c
index af0456d..fb28c42 100644
--- a/board/cray/L1/L1.c
+++ b/board/cray/L1/L1.c
@@ -109,7 +109,7 @@
static void init_sdram (void);
/* ------------------------------------------------------------------------- */
-int board_pre_init (void)
+int board_early_init_f (void)
{
/* Running from ROM: global data is still READONLY */
init_sdram ();
diff --git a/board/dave/PPChameleonEVB/PPChameleonEVB.c b/board/dave/PPChameleonEVB/PPChameleonEVB.c
index 61f7031..603bb1e 100644
--- a/board/dave/PPChameleonEVB/PPChameleonEVB.c
+++ b/board/dave/PPChameleonEVB/PPChameleonEVB.c
@@ -51,7 +51,7 @@
int gunzip(void *, int, unsigned char *, int *);
-int board_pre_init (void)
+int board_early_init_f (void)
{
out32(GPIO0_OR, CFG_NAND0_CE); /* set initial outputs */
out32(GPIO0_OR, CFG_NAND1_CE); /* set initial outputs */
diff --git a/board/ebony/ebony.c b/board/ebony/ebony.c
index bb284ae..a5b3fb6 100644
--- a/board/ebony/ebony.c
+++ b/board/ebony/ebony.c
@@ -32,7 +32,7 @@
long int fixed_sdram (void);
-int board_pre_init (void)
+int board_early_init_f (void)
{
uint reg;
unsigned char *fpga_base = (unsigned char *) CFG_FPGA_BASE;
diff --git a/board/eltec/mhpc/mhpc.c b/board/eltec/mhpc/mhpc.c
index f084ce3..76f9f37 100644
--- a/board/eltec/mhpc/mhpc.c
+++ b/board/eltec/mhpc/mhpc.c
@@ -104,7 +104,7 @@
/* ------------------------------------------------------------------------- */
-int board_pre_init (void)
+int board_early_init_f (void)
{
volatile immap_t *im = (immap_t *)CFG_IMMR;
volatile cpm8xx_t *cp = &(im->im_cpm);
diff --git a/board/ep8260/ep8260.c b/board/ep8260/ep8260.c
index a49c53e..7a2c23f 100644
--- a/board/ep8260/ep8260.c
+++ b/board/ep8260/ep8260.c
@@ -188,7 +188,7 @@
* Setup CS4 to enable the Board Control/Status registers.
* Otherwise the smcs won't work.
*/
-int board_pre_init (void)
+int board_early_init_f (void)
{
volatile t_ep_regs *regs = (t_ep_regs*)CFG_REGS_BASE;
volatile immap_t *immap = (immap_t *)CFG_IMMR;
diff --git a/board/eric/eric.c b/board/eric/eric.c
index 17fe6ac..860e506 100644
--- a/board/eric/eric.c
+++ b/board/eric/eric.c
@@ -31,7 +31,7 @@
#define IBM405GP_GPIO0_ODR 0xef600718 /* GPIO Open Drain */
#define IBM405GP_GPIO0_IR 0xef60071c /* GPIO Input */
-int board_pre_init (void)
+int board_early_init_f (void)
{
/*-------------------------------------------------------------------------+
diff --git a/board/esd/adciop/adciop.c b/board/esd/adciop/adciop.c
index 0c12e98..93bc843 100644
--- a/board/esd/adciop/adciop.c
+++ b/board/esd/adciop/adciop.c
@@ -31,7 +31,7 @@
/* ------------------------------------------------------------------------- */
-int board_pre_init (void)
+int board_early_init_f (void)
{
/*
* Set port pin in escc2 to keep living, and configure user led output
diff --git a/board/esd/ar405/ar405.c b/board/esd/ar405/ar405.c
index d0b06e6..6535a19 100644
--- a/board/esd/ar405/ar405.c
+++ b/board/esd/ar405/ar405.c
@@ -46,7 +46,7 @@
#include "../common/fpga.c"
-int board_pre_init (void)
+int board_early_init_f (void)
{
DECLARE_GLOBAL_DATA_PTR;
diff --git a/board/esd/ash405/ash405.c b/board/esd/ash405/ash405.c
index 39b2dfc..22b3828 100644
--- a/board/esd/ash405/ash405.c
+++ b/board/esd/ash405/ash405.c
@@ -50,7 +50,7 @@
int gunzip(void *, int, unsigned char *, int *);
-int board_pre_init (void)
+int board_early_init_f (void)
{
/*
* IRQ 0-15 405GP internally generated; active high; level sensitive
diff --git a/board/esd/canbt/canbt.c b/board/esd/canbt/canbt.c
index ae0e880..ab49249 100644
--- a/board/esd/canbt/canbt.c
+++ b/board/esd/canbt/canbt.c
@@ -48,7 +48,7 @@
#include "../common/fpga.c"
-int board_pre_init (void)
+int board_early_init_f (void)
{
DECLARE_GLOBAL_DATA_PTR;
diff --git a/board/esd/cpci405/cpci405.c b/board/esd/cpci405/cpci405.c
index 461e3a5..1b90d05 100644
--- a/board/esd/cpci405/cpci405.c
+++ b/board/esd/cpci405/cpci405.c
@@ -57,7 +57,7 @@
int gunzip(void *, int, unsigned char *, int *);
-int board_pre_init (void)
+int board_early_init_f (void)
{
#ifndef CONFIG_CPCI405_VER2
int index, len, i;
diff --git a/board/esd/cpci440/cpci440.c b/board/esd/cpci440/cpci440.c
index 66cfe06..20c8303 100644
--- a/board/esd/cpci440/cpci440.c
+++ b/board/esd/cpci440/cpci440.c
@@ -28,7 +28,7 @@
long int fixed_sdram( void );
-int board_pre_init (void)
+int board_early_init_f (void)
{
uint reg;
diff --git a/board/esd/cpciiser4/cpciiser4.c b/board/esd/cpciiser4/cpciiser4.c
index 725abe9..e90f4ea 100644
--- a/board/esd/cpciiser4/cpciiser4.c
+++ b/board/esd/cpciiser4/cpciiser4.c
@@ -52,7 +52,7 @@
#include "../common/fpga.c"
-int board_pre_init (void)
+int board_early_init_f (void)
{
DECLARE_GLOBAL_DATA_PTR;
diff --git a/board/esd/dasa_sim/dasa_sim.c b/board/esd/dasa_sim/dasa_sim.c
index c1b9093..57a971f 100644
--- a/board/esd/dasa_sim/dasa_sim.c
+++ b/board/esd/dasa_sim/dasa_sim.c
@@ -137,7 +137,7 @@
}
-int board_pre_init (void)
+int board_early_init_f (void)
{
/*
* Init pci regs
diff --git a/board/esd/dp405/dp405.c b/board/esd/dp405/dp405.c
index 6d99b60..84a4a33 100644
--- a/board/esd/dp405/dp405.c
+++ b/board/esd/dp405/dp405.c
@@ -35,7 +35,7 @@
int filesize = sizeof(fpgadata);
-int board_pre_init (void)
+int board_early_init_f (void)
{
/*
* IRQ 0-15 405GP internally generated; active high; level sensitive
diff --git a/board/esd/du405/du405.c b/board/esd/du405/du405.c
index 7b430ea..6e43bb0 100644
--- a/board/esd/du405/du405.c
+++ b/board/esd/du405/du405.c
@@ -53,7 +53,7 @@
#include "../common/fpga.c"
-int board_pre_init (void)
+int board_early_init_f (void)
{
DECLARE_GLOBAL_DATA_PTR;
diff --git a/board/esd/hub405/hub405.c b/board/esd/hub405/hub405.c
index ba8e8e3..d8e3be2 100644
--- a/board/esd/hub405/hub405.c
+++ b/board/esd/hub405/hub405.c
@@ -29,7 +29,7 @@
/* ------------------------------------------------------------------------- */
-int board_pre_init (void)
+int board_early_init_f (void)
{
/*
* IRQ 0-15 405GP internally generated; active high; level sensitive
diff --git a/board/esd/ocrtc/ocrtc.c b/board/esd/ocrtc/ocrtc.c
index 0600273..dc425ae 100644
--- a/board/esd/ocrtc/ocrtc.c
+++ b/board/esd/ocrtc/ocrtc.c
@@ -29,7 +29,7 @@
/* ------------------------------------------------------------------------- */
-int board_pre_init (void)
+int board_early_init_f (void)
{
/*
* IRQ 0-15 405GP internally generated; active high; level sensitive
diff --git a/board/esd/pci405/pci405.c b/board/esd/pci405/pci405.c
index cc45fa9..44bfe10 100644
--- a/board/esd/pci405/pci405.c
+++ b/board/esd/pci405/pci405.c
@@ -53,7 +53,7 @@
int gunzip(void *, int, unsigned char *, int *);
-int board_pre_init (void)
+int board_early_init_f (void)
{
unsigned long cntrl0Reg;
diff --git a/board/esd/plu405/plu405.c b/board/esd/plu405/plu405.c
index 2efd56d..ebefa67 100644
--- a/board/esd/plu405/plu405.c
+++ b/board/esd/plu405/plu405.c
@@ -50,7 +50,7 @@
int gunzip(void *, int, unsigned char *, int *);
-int board_pre_init (void)
+int board_early_init_f (void)
{
/*
* IRQ 0-15 405GP internally generated; active high; level sensitive
diff --git a/board/esd/pmc405/pmc405.c b/board/esd/pmc405/pmc405.c
index 5410a56..6d2432c 100644
--- a/board/esd/pmc405/pmc405.c
+++ b/board/esd/pmc405/pmc405.c
@@ -35,7 +35,7 @@
int filesize = sizeof(fpgadata);
-int board_pre_init (void)
+int board_early_init_f (void)
{
/*
* IRQ 0-15 405GP internally generated; active high; level sensitive
diff --git a/board/esd/voh405/voh405.c b/board/esd/voh405/voh405.c
index d951138..d62c570 100644
--- a/board/esd/voh405/voh405.c
+++ b/board/esd/voh405/voh405.c
@@ -50,7 +50,7 @@
int gunzip(void *, int, unsigned char *, int *);
-int board_pre_init (void)
+int board_early_init_f (void)
{
/*
* IRQ 0-15 405GP internally generated; active high; level sensitive
diff --git a/board/evb64260/bootseq.txt b/board/evb64260/bootseq.txt
index 648c2ff..391d49a 100644
--- a/board/evb64260/bootseq.txt
+++ b/board/evb64260/bootseq.txt
@@ -58,7 +58,7 @@
call cpu_init_f
debug leds
board_init_f: (common/board.c)
- board_pre_init:
+ board_early_init_f:
remap gt regs?
map PCI mem/io
map device space
diff --git a/board/evb64260/evb64260.c b/board/evb64260/evb64260.c
index 99717be..6a9d164 100644
--- a/board/evb64260/evb64260.c
+++ b/board/evb64260/evb64260.c
@@ -57,7 +57,7 @@
/* Unfortunately, we cant change it while we are in flash, so we initialize it
* to the "final" value. This means that any debug_led calls before
- * board_pre_init wont work right (like in cpu_init_f).
+ * board_early_init_f wont work right (like in cpu_init_f).
* See also my_remap_gt_regs below. (NTL)
*/
@@ -182,11 +182,11 @@
}
/*
- * board_pre_init.
+ * board_early_init_f.
*
* set up gal. device mappings, etc.
*/
-int board_pre_init (void)
+int board_early_init_f (void)
{
uchar sram_boot = 0;
diff --git a/board/exbitgen/exbitgen.c b/board/exbitgen/exbitgen.c
index f2cd8ca..39a9722 100644
--- a/board/exbitgen/exbitgen.c
+++ b/board/exbitgen/exbitgen.c
@@ -4,7 +4,7 @@
#include "exbitgen.h"
/* ************************************************************************ */
-int board_pre_init (void)
+int board_early_init_f (void)
/* ------------------------------------------------------------------------ --
* Purpose :
* Remarks :
diff --git a/board/ip860/ip860.c b/board/ip860/ip860.c
index d66621c..5b634e4 100644
--- a/board/ip860/ip860.c
+++ b/board/ip860/ip860.c
@@ -85,7 +85,7 @@
/* ------------------------------------------------------------------------- */
-int board_pre_init(void)
+int board_early_init_f(void)
{
volatile immap_t *immap = (immap_t *)CFG_IMMR;
volatile memctl8xx_t *memctl = &immap->im_memctl;
diff --git a/board/ixdp425/ixdp425.c b/board/ixdp425/ixdp425.c
index 22617b3..1b34f96 100644
--- a/board/ixdp425/ixdp425.c
+++ b/board/ixdp425/ixdp425.c
@@ -40,7 +40,7 @@
int
/**********************************************************/
-board_post_init (void)
+board_late_init (void)
/**********************************************************/
{
return (0);
diff --git a/board/lubbock/lubbock.c b/board/lubbock/lubbock.c
index dcb5087..353c722 100644
--- a/board/lubbock/lubbock.c
+++ b/board/lubbock/lubbock.c
@@ -50,10 +50,10 @@
return 0;
}
-int board_post_init(void)
+int board_late_init(void)
{
- setenv("stdout", "serial");
- setenv("stderr", "serial");
+ setenv("stdout", "serial");
+ setenv("stderr", "serial");
return 0;
}
@@ -71,5 +71,5 @@
gd->bd->bi_dram[3].start = PHYS_SDRAM_4;
gd->bd->bi_dram[3].size = PHYS_SDRAM_4_SIZE;
- return 0;
+ return 0;
}
diff --git a/board/lwmon/flash.c b/board/lwmon/flash.c
index 127738a..4004865 100644
--- a/board/lwmon/flash.c
+++ b/board/lwmon/flash.c
@@ -47,6 +47,9 @@
*/
static ulong flash_get_size (vu_long *addr, flash_info_t *info);
static int write_data (flash_info_t *info, ulong dest, ulong data);
+#ifdef CFG_FLASH_USE_BUFFER_WRITE
+static int write_data_buf (flash_info_t * info, ulong dest, uchar * cp, int len);
+#endif
static void flash_get_offsets (ulong base, flash_info_t *info);
/*-----------------------------------------------------------------------
@@ -480,6 +483,17 @@
/*
* handle FLASH_WIDTH aligned part
*/
+#ifdef CFG_FLASH_USE_BUFFER_WRITE
+ while(cnt >= FLASH_WIDTH) {
+ i = CFG_FLASH_BUFFER_SIZE > cnt ?
+ (cnt & ~(FLASH_WIDTH - 1)) : CFG_FLASH_BUFFER_SIZE;
+ if((rc = write_data_buf(info, wp, src,i)) != 0)
+ return rc;
+ wp += i;
+ src += i;
+ cnt -=i;
+ }
+#else
while (cnt >= FLASH_WIDTH) {
data = 0;
for (i=0; i<FLASH_WIDTH; ++i) {
@@ -491,6 +505,7 @@
wp += FLASH_WIDTH;
cnt -= FLASH_WIDTH;
}
+#endif /* CFG_FLASH_USE_BUFFER_WRITE */
if (cnt == 0) {
return (0);
@@ -512,6 +527,28 @@
}
/*-----------------------------------------------------------------------
+ * Check flash status, returns:
+ * 0 - OK
+ * 1 - timeout
+ */
+static int flash_status_check(vu_long *addr, ulong tout, char * prompt)
+{
+ ulong status;
+ ulong start;
+
+ /* Wait for command completion */
+ start = get_timer (0);
+ while(((status = *addr) & 0x00800080) != 0x00800080) {
+ if (get_timer(start) > tout) {
+ printf("Flash %s timeout at address %p\n", prompt, addr);
+ *addr = 0x00FF00FF; /* restore read mode */
+ return (1);
+ }
+ }
+ return 0;
+}
+
+/*-----------------------------------------------------------------------
* Write a word to Flash, returns:
* 0 - OK
* 1 - write timeout
@@ -520,8 +557,6 @@
static int write_data (flash_info_t *info, ulong dest, ulong data)
{
vu_long *addr = (vu_long *)dest;
- ulong status;
- ulong start;
int flag;
/* Check if Flash is (sufficiently) erased */
@@ -538,13 +573,8 @@
if (flag)
enable_interrupts();
- start = get_timer (0);
-
- while (((status = *addr) & 0x00800080) != 0x00800080) {
- if (get_timer(start) > CFG_FLASH_WRITE_TOUT) {
- *addr = 0x00FF00FF; /* restore read mode */
- return (1);
- }
+ if (flash_status_check(addr, CFG_FLASH_WRITE_TOUT, "write") != 0) {
+ return (1);
}
*addr = 0x00FF00FF; /* restore read mode */
@@ -552,5 +582,46 @@
return (0);
}
+#ifdef CFG_FLASH_USE_BUFFER_WRITE
+/*-----------------------------------------------------------------------
+ * Write a buffer to Flash, returns:
+ * 0 - OK
+ * 1 - write timeout
+ */
+static int write_data_buf(flash_info_t * info, ulong dest, uchar * cp, int len)
+{
+ vu_long *addr = (vu_long *)dest;
+ int sector;
+ int cnt;
+ int retcode;
+ vu_long * src = (vu_long *)cp;
+ vu_long * dst = (vu_long *)dest;
+
+ /* find sector */
+ for(sector = info->sector_count - 1; sector >= 0; sector--) {
+ if(dest >= info->start[sector])
+ break;
+ }
+
+ *addr = 0x00500050; /* clear status */
+ *addr = 0x00e800e8; /* write buffer */
+
+ if((retcode = flash_status_check(addr, CFG_FLASH_BUFFER_WRITE_TOUT,
+ "write to buffer")) == 0) {
+ cnt = len / FLASH_WIDTH;
+ *addr = (cnt-1) | ((cnt-1) << 16);
+ while(cnt-- > 0) {
+ *dst++ = *src++;
+ }
+ *addr = 0x00d000d0; /* write buffer confirm */
+ retcode = flash_status_check(addr, CFG_FLASH_BUFFER_WRITE_TOUT,
+ "buffer write");
+ }
+ *addr = 0x00FF00FF; /* restore read mode */
+ *addr = 0x00500050; /* clear status */
+ return retcode;
+}
+#endif /* CFG_USE_FLASH_BUFFER_WRITE */
+
/*-----------------------------------------------------------------------
*/
diff --git a/board/lwmon/lwmon.c b/board/lwmon/lwmon.c
index 3ec9fa5..6776dbf 100644
--- a/board/lwmon/lwmon.c
+++ b/board/lwmon/lwmon.c
@@ -339,14 +339,14 @@
#endif
/***********************************************************************
-F* Function: int board_pre_init (void) P*A*Z*
+F* Function: int board_early_init_f (void) P*A*Z*
*
P* Parameters: none
P*
P* Returnvalue: int
P* - 0 is always returned.
*
-Z* Intention: This function is the board_pre_init() method implementation
+Z* Intention: This function is the board_early_init_f() method implementation
Z* for the lwmon board.
Z* Disable Ethernet TENA on Port B.
*
@@ -354,7 +354,7 @@
C* Coding: wd@denx.de
V* Verification: dzu@denx.de
***********************************************************************/
-int board_pre_init (void)
+int board_early_init_f (void)
{
volatile immap_t *immr = (immap_t *) CFG_IMMR;
diff --git a/board/ml2/ml2.c b/board/ml2/ml2.c
index 6cc1bec..ff5f816 100644
--- a/board/ml2/ml2.c
+++ b/board/ml2/ml2.c
@@ -22,7 +22,7 @@
#include <asm/processor.h>
-int board_pre_init (void)
+int board_early_init_f (void)
{
return 0;
}
diff --git a/board/mpc8260ads/mpc8260ads.c b/board/mpc8260ads/mpc8260ads.c
index 3de0387..67a7523 100644
--- a/board/mpc8260ads/mpc8260ads.c
+++ b/board/mpc8260ads/mpc8260ads.c
@@ -225,7 +225,7 @@
#endif /* CONFIG_MII */
}
-int board_pre_init (void)
+int board_early_init_f (void)
{
vu_long *bcsr = (vu_long *)CFG_BCSR;
diff --git a/board/mpc8266ads/mpc8266ads.c b/board/mpc8266ads/mpc8266ads.c
index e2c98b1..8f7273c 100644
--- a/board/mpc8266ads/mpc8266ads.c
+++ b/board/mpc8266ads/mpc8266ads.c
@@ -232,7 +232,7 @@
}
-int board_pre_init (void)
+int board_early_init_f (void)
{
volatile bcsr_t *bcsr = (bcsr_t *)CFG_BCSR;
volatile pci_ic_t *pci_ic = (pci_ic_t *) CFG_PCI_INT;
diff --git a/board/mpc8540ads/mpc8540ads.c b/board/mpc8540ads/mpc8540ads.c
index c21cd9e..0644de8 100644
--- a/board/mpc8540ads/mpc8540ads.c
+++ b/board/mpc8540ads/mpc8540ads.c
@@ -47,7 +47,7 @@
} bcsr_t;
#endif
-int board_pre_init (void)
+int board_early_init_f (void)
{
#if defined(CONFIG_PCI)
volatile immap_t *immr = (immap_t *)CFG_IMMR;
diff --git a/board/mpc8560ads/mpc8560ads.c b/board/mpc8560ads/mpc8560ads.c
index 5567b69..823ab0d 100644
--- a/board/mpc8560ads/mpc8560ads.c
+++ b/board/mpc8560ads/mpc8560ads.c
@@ -199,7 +199,7 @@
volatile unsigned char bcsr5;
} bcsr_t;
-int board_pre_init (void)
+int board_early_init_f (void)
{
#if defined(CONFIG_PCI)
volatile immap_t *immr = (immap_t *)CFG_IMMR;
diff --git a/board/mpl/mip405/mip405.c b/board/mpl/mip405/mip405.c
index c147175..709e1a4 100644
--- a/board/mpl/mip405/mip405.c
+++ b/board/mpl/mip405/mip405.c
@@ -469,7 +469,7 @@
return (0);
}
-int board_pre_init (void)
+int board_early_init_f (void)
{
init_sdram ();
diff --git a/board/mpl/pip405/pip405.c b/board/mpl/pip405/pip405.c
index b4715aa..590bd20 100644
--- a/board/mpl/pip405/pip405.c
+++ b/board/mpl/pip405/pip405.c
@@ -176,7 +176,7 @@
#endif
-int board_pre_init (void)
+int board_early_init_f (void)
{
unsigned char dataout[1];
unsigned char datain[128];
diff --git a/board/netvia/netvia.c b/board/netvia/netvia.c
index db36b22..fb7f770 100644
--- a/board/netvia/netvia.c
+++ b/board/netvia/netvia.c
@@ -356,7 +356,7 @@
#error Unknown NETVIA board version.
#endif
-int board_pre_init(void)
+int board_early_init_f(void)
{
volatile immap_t *immap = (immap_t *) CFG_IMMR;
volatile iop8xx_t *ioport = &immap->im_ioport;
diff --git a/board/oxc/oxc.c b/board/oxc/oxc.c
index 8ac0e79..fa7ff02 100644
--- a/board/oxc/oxc.c
+++ b/board/oxc/oxc.c
@@ -87,7 +87,7 @@
pci_mpc824x_init(&hose);
}
-int board_pre_init (void)
+int board_early_init_f (void)
{
*(volatile unsigned char *)(CFG_CPLD_RESET) = 0x89;
return 0;
diff --git a/board/pcippc2/pcippc2.c b/board/pcippc2/pcippc2.c
index a0fe39a..231b505 100644
--- a/board/pcippc2/pcippc2.c
+++ b/board/pcippc2/pcippc2.c
@@ -75,7 +75,7 @@
return (-1);
}
-int board_pre_init (void)
+int board_early_init_f (void)
{
out32 (REG (CPC0, RSTR), 0xC0000000);
iobarrier_rw ();
diff --git a/board/rpxsuper/rpxsuper.c b/board/rpxsuper/rpxsuper.c
index 50b3c5c..b4331f1 100644
--- a/board/rpxsuper/rpxsuper.c
+++ b/board/rpxsuper/rpxsuper.c
@@ -191,7 +191,7 @@
* Setup CS4 to enable the Board Control/Status registers.
* Otherwise the smcs won't work.
*/
-int board_pre_init (void)
+int board_early_init_f (void)
{
volatile t_rpx_regs *regs = (t_rpx_regs*)CFG_REGS_BASE;
volatile immap_t *immap = (immap_t *)CFG_IMMR;
diff --git a/board/siemens/IAD210/IAD210.c b/board/siemens/IAD210/IAD210.c
index 1243887..52cd4e6 100644
--- a/board/siemens/IAD210/IAD210.c
+++ b/board/siemens/IAD210/IAD210.c
@@ -228,7 +228,7 @@
iop->iop_pdpar |= 0x0080; /* set pin as MII_clock */
}
-int board_pre_init (void)
+int board_early_init_f (void)
{
volatile immap_t *immap = (immap_t *) CFG_IMMR;
volatile cpmtimer8xx_t *timers = &immap->im_cpmtimer;
diff --git a/board/tqm8xx/tqm8xx.c b/board/tqm8xx/tqm8xx.c
index 1fbceb5..73bee32 100644
--- a/board/tqm8xx/tqm8xx.c
+++ b/board/tqm8xx/tqm8xx.c
@@ -419,6 +419,14 @@
{ BASE_BAUD, 6, (void*)0xec160000 },
{ BASE_BAUD, 10, (void*)0xec170000 },
};
+
+#ifdef CONFIG_BOARD_EARLY_INIT_R
+int board_early_init_r (void)
+{
+ ps2mult_early_init();
+ return (0);
+}
+#endif
#endif /* CONFIG_BMS2003 */
#endif /* CONFIG_PS2MULT */
diff --git a/board/w7o/w7o.c b/board/w7o/w7o.c
index 924a449..1e3ceb2 100644
--- a/board/w7o/w7o.c
+++ b/board/w7o/w7o.c
@@ -41,7 +41,7 @@
/* ------------------------------------------------------------------------- */
-int board_pre_init (void)
+int board_early_init_f (void)
{
#if defined(CONFIG_W7OLMG)
/*
diff --git a/board/walnut405/walnut405.c b/board/walnut405/walnut405.c
index 1d02ad4..7035599 100644
--- a/board/walnut405/walnut405.c
+++ b/board/walnut405/walnut405.c
@@ -26,7 +26,7 @@
#include <asm/processor.h>
#include <spd_sdram.h>
-int board_pre_init (void)
+int board_early_init_f (void)
{
/*-------------------------------------------------------------------------+
| Interrupt controller setup for the Walnut board.
diff --git a/cpu/74xx_7xx/start.S b/cpu/74xx_7xx/start.S
index e8854f0..534c818 100644
--- a/cpu/74xx_7xx/start.S
+++ b/cpu/74xx_7xx/start.S
@@ -267,7 +267,7 @@
* everything is write-through.
* The init-mem BAT can be reused after reloc. The old
* gt-regs BAT can be reused after board_init_f calls
- * board_pre_init (EVB only).
+ * board_early_init_f (EVB only).
*/
#if !defined(CONFIG_BAB7xx) && !defined(CONFIG_ELPPC)
/* enable address translation */
diff --git a/cpu/mpc8xx/spi.c b/cpu/mpc8xx/spi.c
index 16b3f3a..5d75207 100644
--- a/cpu/mpc8xx/spi.c
+++ b/cpu/mpc8xx/spi.c
@@ -503,8 +503,7 @@
char c = (char) length;
int i;
- for (i = 0; i < length; i++)
- {
+ for (i = 0; i < length; i++) {
if (packet[i] != c++) return -1;
}
@@ -513,37 +512,32 @@
int spi_post_test (int flags)
{
- DECLARE_GLOBAL_DATA_PTR;
-
int res = -1;
volatile immap_t *immr = (immap_t *) CFG_IMMR;
- volatile cpm8xx_t *cp = (cpm8xx_t *) &immr->im_cpm;
+ volatile cpm8xx_t *cp = (cpm8xx_t *) & immr->im_cpm;
int i;
int l;
- spi_init_f();
- spi_init_r();
+ spi_init_f ();
+ spi_init_r ();
cp->cp_spmode |= SPMODE_LOOP;
- for (i = 0; i < TEST_NUM; i++)
- {
- for (l = TEST_MIN_LENGTH; l <= TEST_MAX_LENGTH; l += 8)
- {
- packet_fill(txbuf, l);
+ for (i = 0; i < TEST_NUM; i++) {
+ for (l = TEST_MIN_LENGTH; l <= TEST_MAX_LENGTH; l += 8) {
+ packet_fill (txbuf, l);
- spi_xfer(l);
+ spi_xfer (l);
- if (packet_check(rxbuf, l) < 0)
- {
- goto Done;
+ if (packet_check (rxbuf, l) < 0) {
+ goto Done;
+ }
}
- }
}
res = 0;
- Done:
+ Done:
cp->cp_spmode &= ~SPMODE_LOOP;
@@ -554,16 +548,11 @@
*/
#if defined(CONFIG_8xx_CONS_SCC2)
- serial_init();
+ serial_init ();
#endif
-#if defined(SCC_ENET) && (SCC_ENET == 1)
- eth_init(gd->bd);
-#endif
-
- if (res != 0)
- {
- post_log("SPI test failed\n");
+ if (res != 0) {
+ post_log ("SPI test failed\n");
}
return res;
diff --git a/drivers/keyboard.c b/drivers/keyboard.c
index 7ba87be..738ff9f 100644
--- a/drivers/keyboard.c
+++ b/drivers/keyboard.c
@@ -194,8 +194,14 @@
case 0xBA: /* caps lock released */
return; /* just swallow */
}
+#if 0
if((scancode&0x80)==0x80) /* key released */
return;
+#else
+ if((scancode&0x80)==0x00) /* key pressed */
+ return;
+ scancode &= ~0x80;
+#endif
/* now, decide which table we need */
if(scancode > (sizeof(kbd_plain_xlate)/sizeof(kbd_plain_xlate[0]))) { /* scancode not in list */
PRINTF("unkown scancode %X\n",scancode);
diff --git a/drivers/ps2mult.c b/drivers/ps2mult.c
index c0457b8..9515a0f 100644
--- a/drivers/ps2mult.c
+++ b/drivers/ps2mult.c
@@ -42,6 +42,7 @@
#endif
+static ulong start_time;
static int init_done = 0;
static int received_escape = 0;
@@ -63,6 +64,13 @@
static u_char ps2mult_buf_status [PS2BUF_SIZE];
+#ifndef CONFIG_BOARD_EARLY_INIT_R
+#error #define CONFIG_BOARD_EARLY_INIT_R and call ps2mult_early_init() in board_early_init_r()
+#endif
+void ps2mult_early_init (void)
+{
+ start_time = get_timer(0);
+}
static void ps2mult_send_byte(u_char byte, u_char sel)
{
@@ -360,6 +368,8 @@
int kbd_found = 0;
int mouse_found = 0;
+ while (get_timer(start_time) < CONFIG_PS2MULT_DELAY);
+
ps2ser_init();
ps2ser_putc(PS2MULT_SESSION_START);
diff --git a/include/common.h b/include/common.h
index f4656fc..206f8cf 100644
--- a/include/common.h
+++ b/include/common.h
@@ -285,9 +285,10 @@
void load_sernum_ethaddr (void);
/* $(BOARD)/$(BOARD).c */
-int board_pre_init (void);
-int board_post_init (void);
+int board_early_init_f (void);
+int board_late_init (void);
int board_postclk_init (void); /* after clocks/timebase, before env/serial */
+int board_early_init_r (void);
void board_poweroff (void);
#if defined(CFG_DRAM_TEST)
diff --git a/include/configs/ADCIOP.h b/include/configs/ADCIOP.h
index 255942a..5a62139 100644
--- a/include/configs/ADCIOP.h
+++ b/include/configs/ADCIOP.h
@@ -12,7 +12,7 @@
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
@@ -34,27 +34,27 @@
*/
#define CONFIG_IOP480 1 /* This is a IOP480 CPU */
-#define CONFIG_ADCIOP 1 /* ...on a ADCIOP board */
+#define CONFIG_ADCIOP 1 /* ...on a ADCIOP board */
-#define CONFIG_BOARD_PRE_INIT 1 /* call board_pre_init() */
+#define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */
-#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */
+#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */
-#define CONFIG_CPUCLOCK 66
-#define CONFIG_BUSCLOCK (CONFIG_CPUCLOCK)
+#define CONFIG_CPUCLOCK 66
+#define CONFIG_BUSCLOCK (CONFIG_CPUCLOCK)
-#define CONFIG_BAUDRATE 9600
+#define CONFIG_BAUDRATE 9600
#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */
#define CONFIG_BOOTCOMMAND "bootm ffc00000" /* autoboot command */
-#undef CONFIG_BOOTARGS
+#undef CONFIG_BOOTARGS
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
#undef CONFIG_WATCHDOG /* watchdog disabled */
-#define CONFIG_PHY_ADDR 0 /* PHY address */
+#define CONFIG_PHY_ADDR 0 /* PHY address */
#define CONFIG_IPADDR 10.0.18.222
#define CONFIG_SERVERIP 10.0.18.190
@@ -62,7 +62,7 @@
#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \
CFG_CMD_DHCP | \
CFG_CMD_IRQ | \
- CFG_CMD_ELF | \
+ CFG_CMD_ELF | \
CFG_CMD_ASKENV )
/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
@@ -74,33 +74,33 @@
#define CFG_LONGHELP /* undef to save memory */
#define CFG_PROMPT "=> " /* Monitor Command Prompt */
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
#endif
#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
#define CFG_MAXARGS 16 /* max number of command args */
#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
+#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
/* The following table includes the supported baudrates */
-#define CFG_BAUDRATE_TABLE \
+#define CFG_BAUDRATE_TABLE \
{ 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200 }
-#define CFG_LOAD_ADDR 0x100000 /* default load address */
+#define CFG_LOAD_ADDR 0x100000 /* default load address */
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
/*-----------------------------------------------------------------------
* Definitions for initial stack pointer and data area (in DPRAM)
*/
-#define CFG_INIT_RAM_ADDR 0x00df0000 /* inside of SDRAM */
+#define CFG_INIT_RAM_ADDR 0x00df0000 /* inside of SDRAM */
#define CFG_INIT_RAM_END 0x0f00 /* End of used area in RAM */
#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
@@ -122,28 +122,28 @@
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
/*-----------------------------------------------------------------------
* FLASH organization
*/
#define CFG_MAX_FLASH_BANKS 2 /* max number of memory banks */
-#define CFG_MAX_FLASH_SECT 256 /* max number of sectors on one chip */
+#define CFG_MAX_FLASH_SECT 256 /* max number of sectors on one chip */
#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
-#define CFG_FLASH_WORD_SIZE unsigned char /* flash word size (width) */
-#define CFG_FLASH_ADDR0 0x0AA9 /* 1st address for flash config cycles */
-#define CFG_FLASH_ADDR1 0x0556 /* 2nd address for flash config cycles */
+#define CFG_FLASH_WORD_SIZE unsigned char /* flash word size (width) */
+#define CFG_FLASH_ADDR0 0x0AA9 /* 1st address for flash config cycles */
+#define CFG_FLASH_ADDR1 0x0556 /* 2nd address for flash config cycles */
/*
* The following defines are added for buggy IOP480 byte interface.
* All other boards should use the standard values (CPCI405 etc.)
*/
-#define CFG_FLASH_READ0 0x0002 /* 0 is standard */
-#define CFG_FLASH_READ1 0x0000 /* 1 is standard */
-#define CFG_FLASH_READ2 0x0004 /* 2 is standard */
+#define CFG_FLASH_READ0 0x0002 /* 0 is standard */
+#define CFG_FLASH_READ1 0x0000 /* 1 is standard */
+#define CFG_FLASH_READ2 0x0004 /* 2 is standard */
-#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
+#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
#if 1 /* Use NVRAM for environment variables */
/*-----------------------------------------------------------------------
@@ -159,8 +159,8 @@
#else /* Use FLASH for environment variables */
-#define CFG_ENV_IS_IN_FLASH 1
-#define CFG_ENV_OFFSET 0x00010000 /* Offset of Environment Sector */
+#define CFG_ENV_IS_IN_FLASH 1
+#define CFG_ENV_OFFSET 0x00010000 /* Offset of Environment Sector */
#define CFG_ENV_SIZE 0x1000 /* Total Size of Environment Sector */
#define CFG_ENV_SECT_SIZE 0x8000 /* see README - env sector total size */
@@ -173,12 +173,12 @@
#define CONFIG_PCI /* include pci support */
#undef CONFIG_PCI_PNP
-#define CONFIG_NET_MULTI /* Multi ethernet cards support */
+#define CONFIG_NET_MULTI /* Multi ethernet cards support */
#define CONFIG_TULIP
-#define CFG_ETH_DEV_FN 0x0000
-#define CFG_ETH_IOBASE 0x0fff0000
+#define CFG_ETH_DEV_FN 0x0000
+#define CFG_ETH_IOBASE 0x0fff0000
/*-----------------------------------------------------------------------
* Cache Configuration
diff --git a/include/configs/AR405.h b/include/configs/AR405.h
index 847edbc..1fae916 100644
--- a/include/configs/AR405.h
+++ b/include/configs/AR405.h
@@ -34,12 +34,12 @@
*/
#define CONFIG_405GP 1 /* This is a PPC405GP CPU */
-#define CONFIG_4xx 1 /* ...member of PPC4xx family */
-#define CONFIG_AR405 1 /* ...on a AR405 board */
+#define CONFIG_4xx 1 /* ...member of PPC4xx family */
+#define CONFIG_AR405 1 /* ...on a AR405 board */
-#define CONFIG_BOARD_PRE_INIT 1 /* call board_pre_init() */
+#define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */
-#define CONFIG_SYS_CLK_FREQ 33000000 /* external frequency to pll */
+#define CONFIG_SYS_CLK_FREQ 33000000 /* external frequency to pll */
#define CONFIG_BAUDRATE 9600
#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */
@@ -51,8 +51,8 @@
#endif
#if 0
-#define CONFIG_BOOTARGS "root=/dev/nfs " \
- "ip=192.168.2.176:192.168.2.190:192.168.2.79:255.255.255.0 " \
+#define CONFIG_BOOTARGS "root=/dev/nfs " \
+ "ip=192.168.2.176:192.168.2.190:192.168.2.79:255.255.255.0 " \
"nfsroot=192.168.2.190:/home/stefan/cpci405/target_ftest4"
#else
#define CONFIG_BOOTARGS "root=/dev/hda1 " \
@@ -64,7 +64,7 @@
#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
#define CONFIG_MII 1 /* MII PHY management */
-#define CONFIG_PHY_ADDR 0 /* PHY address */
+#define CONFIG_PHY_ADDR 0 /* PHY address */
#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \
CFG_CMD_PCI | \
@@ -76,7 +76,7 @@
#undef CONFIG_WATCHDOG /* watchdog disabled */
-#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */
+#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */
/*
* Miscellaneous configurable options
@@ -84,30 +84,30 @@
#define CFG_LONGHELP /* undef to save memory */
#define CFG_PROMPT "=> " /* Monitor Command Prompt */
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
#endif
#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
#define CFG_MAXARGS 16 /* max number of command args */
#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
+#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-#define CFG_EXT_SERIAL_CLOCK 14745600 /* use external serial clock */
+#define CFG_EXT_SERIAL_CLOCK 14745600 /* use external serial clock */
/* The following table includes the supported baudrates */
-#define CFG_BAUDRATE_TABLE \
+#define CFG_BAUDRATE_TABLE \
{ 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \
57600, 115200, 230400, 460800, 921600 }
#define CFG_LOAD_ADDR 0x100000 /* default load address */
#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
@@ -115,27 +115,27 @@
* PCI stuff
*-----------------------------------------------------------------------
*/
-#define PCI_HOST_ADAPTER 0 /* configure ar pci adapter */
-#define PCI_HOST_FORCE 1 /* configure as pci host */
-#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
+#define PCI_HOST_ADAPTER 0 /* configure ar pci adapter */
+#define PCI_HOST_FORCE 1 /* configure as pci host */
+#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
-#define CONFIG_PCI /* include pci support */
-#define CONFIG_PCI_HOST PCI_HOST_FORCE /* select pci host function */
-#define CONFIG_PCI_PNP /* do pci plug-and-play */
- /* resource configuration */
+#define CONFIG_PCI /* include pci support */
+#define CONFIG_PCI_HOST PCI_HOST_FORCE /* select pci host function */
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
+ /* resource configuration */
-#define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */
+#define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */
-#define CONFIG_PCI_BOOTDELAY 0 /* enable pci bootdelay variable*/
+#define CONFIG_PCI_BOOTDELAY 0 /* enable pci bootdelay variable*/
-#define CFG_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */
-#define CFG_PCI_SUBSYS_DEVICEID 0x0403 /* PCI Device ID: ARISTO405 */
-#define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */
-#define CFG_PCI_PTM1MS 0x80000001 /* 2GB, enable hard-wired to 1 */
-#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
-#define CFG_PCI_PTM2LA 0xfff00000 /* point to flash */
-#define CFG_PCI_PTM2MS 0xfff00001 /* 1MB, enable */
-#define CFG_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */
+#define CFG_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */
+#define CFG_PCI_SUBSYS_DEVICEID 0x0403 /* PCI Device ID: ARISTO405 */
+#define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */
+#define CFG_PCI_PTM1MS 0x80000001 /* 2GB, enable hard-wired to 1 */
+#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
+#define CFG_PCI_PTM2LA 0xfff00000 /* point to flash */
+#define CFG_PCI_PTM2MS 0xfff00001 /* 1MB, enable */
+#define CFG_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */
/*-----------------------------------------------------------------------
* Start addresses for the final memory configuration
@@ -163,24 +163,24 @@
#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
-#define CFG_FLASH_WORD_SIZE unsigned short /* flash word size (width) */
-#define CFG_FLASH_ADDR0 0x5555 /* 1st address for flash config cycles */
-#define CFG_FLASH_ADDR1 0x2AAA /* 2nd address for flash config cycles */
+#define CFG_FLASH_WORD_SIZE unsigned short /* flash word size (width) */
+#define CFG_FLASH_ADDR0 0x5555 /* 1st address for flash config cycles */
+#define CFG_FLASH_ADDR1 0x2AAA /* 2nd address for flash config cycles */
/*
* The following defines are added for buggy IOP480 byte interface.
* All other boards should use the standard values (CPCI405 etc.)
*/
-#define CFG_FLASH_READ0 0x0000 /* 0 is standard */
-#define CFG_FLASH_READ1 0x0001 /* 1 is standard */
-#define CFG_FLASH_READ2 0x0002 /* 2 is standard */
+#define CFG_FLASH_READ0 0x0000 /* 0 is standard */
+#define CFG_FLASH_READ1 0x0001 /* 1 is standard */
+#define CFG_FLASH_READ2 0x0002 /* 2 is standard */
-#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
+#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
-#define CFG_ENV_IS_IN_FLASH 1
-#define CFG_ENV_OFFSET 0x00010000 /* Offset of Environment Sector */
+#define CFG_ENV_IS_IN_FLASH 1
+#define CFG_ENV_OFFSET 0x00010000 /* Offset of Environment Sector */
#define CFG_ENV_SIZE 0x1000 /* Total Size of Environment Sector */
-#define CFG_ENV_SECT_SIZE 0x10000 /* see README - env sector total size */
+#define CFG_ENV_SECT_SIZE 0x10000 /* see README - env sector total size */
/*-----------------------------------------------------------------------
* Cache Configuration
@@ -204,40 +204,40 @@
* External Bus Controller (EBC) Setup
*/
-/* Memory Bank 0 (Flash Bank 0) initialization */
-#define CFG_EBC_PB0AP 0x92015480
-#define CFG_EBC_PB0CR 0xFFC5A000 /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
+/* Memory Bank 0 (Flash Bank 0) initialization */
+#define CFG_EBC_PB0AP 0x92015480
+#define CFG_EBC_PB0CR 0xFFC5A000 /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
-/* Memory Bank 1 (CAN0, 1, 2, 3) initialization */
-#define CFG_EBC_PB1AP 0x01000380 /* enable Ready, BEM=0 */
-#define CFG_EBC_PB1CR 0xF0018000 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */
+/* Memory Bank 1 (CAN0, 1, 2, 3) initialization */
+#define CFG_EBC_PB1AP 0x01000380 /* enable Ready, BEM=0 */
+#define CFG_EBC_PB1CR 0xF0018000 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */
-/* Memory Bank 2 (Expension Bus) initialization */
-#define CFG_EBC_PB2AP 0x01000280 /* disable Ready, BEM=0 */
-#define CFG_EBC_PB2CR 0xF0118000 /* BAS=0xF01,BS=1MB,BU=R/W,BW=8bit */
+/* Memory Bank 2 (Expension Bus) initialization */
+#define CFG_EBC_PB2AP 0x01000280 /* disable Ready, BEM=0 */
+#define CFG_EBC_PB2CR 0xF0118000 /* BAS=0xF01,BS=1MB,BU=R/W,BW=8bit */
-/* Memory Bank 3 (16552) initialization */
-#define CFG_EBC_PB3AP 0x01000380 /* enable Ready, BEM=0 */
-#define CFG_EBC_PB3CR 0xF0218000 /* BAS=0xF02,BS=1MB,BU=R/W,BW=8bit */
+/* Memory Bank 3 (16552) initialization */
+#define CFG_EBC_PB3AP 0x01000380 /* enable Ready, BEM=0 */
+#define CFG_EBC_PB3CR 0xF0218000 /* BAS=0xF02,BS=1MB,BU=R/W,BW=8bit */
-/* Memory Bank 4 (FPGA regs) initialization */
-#define CFG_EBC_PB4AP 0x01005380 /* enable Ready, BEM=0 */
-#define CFG_EBC_PB4CR 0xF031C000 /* BAS=0xF03,BS=1MB,BU=R/W,BW=32bit */
+/* Memory Bank 4 (FPGA regs) initialization */
+#define CFG_EBC_PB4AP 0x01005380 /* enable Ready, BEM=0 */
+#define CFG_EBC_PB4CR 0xF031C000 /* BAS=0xF03,BS=1MB,BU=R/W,BW=32bit */
-/* Memory Bank 5 (Flash Bank 1/DUMMY) initialization */
-#define CFG_EBC_PB5AP 0x92015480
-#define CFG_EBC_PB5CR 0xFF85A000 /* BAS=0xFF8,BS=4MB,BU=R/W,BW=16bit */
+/* Memory Bank 5 (Flash Bank 1/DUMMY) initialization */
+#define CFG_EBC_PB5AP 0x92015480
+#define CFG_EBC_PB5CR 0xFF85A000 /* BAS=0xFF8,BS=4MB,BU=R/W,BW=16bit */
/*-----------------------------------------------------------------------
* Definitions for initial stack pointer and data area (in data cache)
*/
-#define CFG_INIT_DCACHE_CS 7 /* use cs # 7 for data cache memory */
+#define CFG_INIT_DCACHE_CS 7 /* use cs # 7 for data cache memory */
-#define CFG_INIT_RAM_ADDR 0x40000000 /* use data cache */
-#define CFG_INIT_RAM_END 0x2000 /* End of used area in RAM */
+#define CFG_INIT_RAM_ADDR 0x40000000 /* use data cache */
+#define CFG_INIT_RAM_END 0x2000 /* End of used area in RAM */
#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
/*
* Internal Definitions
diff --git a/include/configs/ASH405.h b/include/configs/ASH405.h
index 3868997..7ed01d1 100644
--- a/include/configs/ASH405.h
+++ b/include/configs/ASH405.h
@@ -34,13 +34,13 @@
*/
#define CONFIG_405EP 1 /* This is a PPC405 CPU */
-#define CONFIG_4xx 1 /* ...member of PPC4xx family */
-#define CONFIG_ASH405 1 /* ...on a ASH405 board */
+#define CONFIG_4xx 1 /* ...member of PPC4xx family */
+#define CONFIG_ASH405 1 /* ...on a ASH405 board */
-#define CONFIG_BOARD_PRE_INIT 1 /* call board_pre_init() */
-#define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */
+#define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */
+#define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */
-#define CONFIG_SYS_CLK_FREQ 33333334 /* external frequency to pll */
+#define CONFIG_SYS_CLK_FREQ 33333334 /* external frequency to pll */
#define CONFIG_BAUDRATE 9600
#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */
@@ -60,7 +60,7 @@
#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
#define CONFIG_MII 1 /* MII PHY management */
-#define CONFIG_PHY_ADDR 0 /* PHY address */
+#define CONFIG_PHY_ADDR 0 /* PHY address */
#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \
CFG_CMD_DHCP | \
@@ -71,17 +71,17 @@
CFG_CMD_I2C | \
CFG_CMD_MII | \
CFG_CMD_PING | \
- CFG_CMD_EEPROM )
+ CFG_CMD_EEPROM )
/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
#include <cmd_confdefs.h>
-#undef CONFIG_WATCHDOG /* watchdog disabled */
+#undef CONFIG_WATCHDOG /* watchdog disabled */
-#define CONFIG_RTC_MC146818 /* DS1685 is MC146818 compatible*/
-#define CFG_RTC_REG_BASE_ADDR 0xF0000500 /* RTC Base Address */
+#define CONFIG_RTC_MC146818 /* DS1685 is MC146818 compatible*/
+#define CFG_RTC_REG_BASE_ADDR 0xF0000500 /* RTC Base Address */
-#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */
+#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */
/*
* Miscellaneous configurable options
@@ -91,45 +91,45 @@
#undef CFG_HUSH_PARSER /* use "hush" command parser */
#ifdef CFG_HUSH_PARSER
-#define CFG_PROMPT_HUSH_PS2 "> "
+#define CFG_PROMPT_HUSH_PS2 "> "
#endif
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
#endif
#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
#define CFG_MAXARGS 16 /* max number of command args */
#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_DEVICE_NULLDEV 1 /* include nulldev device */
+#define CFG_DEVICE_NULLDEV 1 /* include nulldev device */
-#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
+#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-#undef CFG_EXT_SERIAL_CLOCK /* no external serial clock used */
-#define CFG_IGNORE_405_UART_ERRATA_59 /* ignore ppc405gp errata #59 */
-#define CFG_BASE_BAUD 691200
-#undef CONFIG_UART1_CONSOLE /* define for uart1 as console */
+#undef CFG_EXT_SERIAL_CLOCK /* no external serial clock used */
+#define CFG_IGNORE_405_UART_ERRATA_59 /* ignore ppc405gp errata #59 */
+#define CFG_BASE_BAUD 691200
+#undef CONFIG_UART1_CONSOLE /* define for uart1 as console */
/* The following table includes the supported baudrates */
-#define CFG_BAUDRATE_TABLE \
+#define CFG_BAUDRATE_TABLE \
{ 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \
57600, 115200, 230400, 460800, 921600 }
#define CFG_LOAD_ADDR 0x100000 /* default load address */
#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
+#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
-#define CFG_RX_ETH_BUFFER 16 /* use 16 rx buffer on 405 emac */
+#define CFG_RX_ETH_BUFFER 16 /* use 16 rx buffer on 405 emac */
/*-----------------------------------------------------------------------
* NAND-FLASH stuff
@@ -142,14 +142,14 @@
#define ADDR_PAGE 2
#define ADDR_COLUMN_PAGE 3
-#define NAND_ChipID_UNKNOWN 0x00
+#define NAND_ChipID_UNKNOWN 0x00
#define NAND_MAX_FLOORS 1
#define NAND_MAX_CHIPS 1
-#define CFG_NAND_CE (0x80000000 >> 1) /* our CE is GPIO1 */
-#define CFG_NAND_CLE (0x80000000 >> 2) /* our CLE is GPIO2 */
-#define CFG_NAND_ALE (0x80000000 >> 3) /* our ALE is GPIO3 */
-#define CFG_NAND_RDY (0x80000000 >> 4) /* our RDY is GPIO4 */
+#define CFG_NAND_CE (0x80000000 >> 1) /* our CE is GPIO1 */
+#define CFG_NAND_CLE (0x80000000 >> 2) /* our CLE is GPIO2 */
+#define CFG_NAND_ALE (0x80000000 >> 3) /* our ALE is GPIO3 */
+#define CFG_NAND_RDY (0x80000000 >> 4) /* our RDY is GPIO4 */
#define NAND_DISABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CE);} while(0)
#define NAND_ENABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CE);} while(0)
@@ -168,26 +168,26 @@
* PCI stuff
*-----------------------------------------------------------------------
*/
-#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */
-#define PCI_HOST_FORCE 1 /* configure as pci host */
-#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
+#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */
+#define PCI_HOST_FORCE 1 /* configure as pci host */
+#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
-#define CONFIG_PCI /* include pci support */
-#define CONFIG_PCI_HOST PCI_HOST_HOST /* select pci host function */
-#undef CONFIG_PCI_PNP /* do pci plug-and-play */
- /* resource configuration */
+#define CONFIG_PCI /* include pci support */
+#define CONFIG_PCI_HOST PCI_HOST_HOST /* select pci host function */
+#undef CONFIG_PCI_PNP /* do pci plug-and-play */
+ /* resource configuration */
-#undef CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */
+#undef CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */
-#define CFG_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */
-#define CFG_PCI_SUBSYS_DEVICEID 0x0405 /* PCI Device ID: CPCI-405 */
-#define CFG_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/
-#define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */
-#define CFG_PCI_PTM1MS 0xfc000001 /* 64MB, enable hard-wired to 1 */
-#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
-#define CFG_PCI_PTM2LA 0xffc00000 /* point to flash */
-#define CFG_PCI_PTM2MS 0xffc00001 /* 4MB, enable */
-#define CFG_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */
+#define CFG_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */
+#define CFG_PCI_SUBSYS_DEVICEID 0x0405 /* PCI Device ID: CPCI-405 */
+#define CFG_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/
+#define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */
+#define CFG_PCI_PTM1MS 0xfc000001 /* 64MB, enable hard-wired to 1 */
+#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
+#define CFG_PCI_PTM2LA 0xffc00000 /* point to flash */
+#define CFG_PCI_PTM2MS 0xffc00001 /* 4MB, enable */
+#define CFG_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */
/*-----------------------------------------------------------------------
* Start addresses for the final memory configuration
@@ -215,34 +215,34 @@
#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
#define CFG_FLASH_WRITE_TOUT 1000 /* Timeout for Flash Write (in ms) */
-#define CFG_FLASH_WORD_SIZE unsigned short /* flash word size (width) */
-#define CFG_FLASH_ADDR0 0x5555 /* 1st address for flash config cycles */
-#define CFG_FLASH_ADDR1 0x2AAA /* 2nd address for flash config cycles */
+#define CFG_FLASH_WORD_SIZE unsigned short /* flash word size (width) */
+#define CFG_FLASH_ADDR0 0x5555 /* 1st address for flash config cycles */
+#define CFG_FLASH_ADDR1 0x2AAA /* 2nd address for flash config cycles */
/*
* The following defines are added for buggy IOP480 byte interface.
* All other boards should use the standard values (CPCI405 etc.)
*/
-#define CFG_FLASH_READ0 0x0000 /* 0 is standard */
-#define CFG_FLASH_READ1 0x0001 /* 1 is standard */
-#define CFG_FLASH_READ2 0x0002 /* 2 is standard */
+#define CFG_FLASH_READ0 0x0000 /* 0 is standard */
+#define CFG_FLASH_READ1 0x0001 /* 1 is standard */
+#define CFG_FLASH_READ2 0x0002 /* 2 is standard */
-#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
+#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
#if 0 /* test-only */
-#define CFG_JFFS2_FIRST_BANK 0 /* use for JFFS2 */
-#define CFG_JFFS2_NUM_BANKS 1 /* ! second bank contains U-Boot */
+#define CFG_JFFS2_FIRST_BANK 0 /* use for JFFS2 */
+#define CFG_JFFS2_NUM_BANKS 1 /* ! second bank contains U-Boot */
#endif
/*-----------------------------------------------------------------------
* Environment Variable setup
*/
-#define CFG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
-#define CFG_ENV_OFFSET 0x100 /* environment starts at the beginning of the EEPROM */
-#define CFG_ENV_SIZE 0x700 /* 2048 bytes may be used for env vars*/
+#define CFG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
+#define CFG_ENV_OFFSET 0x100 /* environment starts at the beginning of the EEPROM */
+#define CFG_ENV_SIZE 0x700 /* 2048 bytes may be used for env vars*/
/* total size of a CAT24WC16 is 2048 bytes */
#define CFG_NVRAM_BASE_ADDR 0xF0000500 /* NVRAM base address */
-#define CFG_NVRAM_SIZE 242 /* NVRAM size */
+#define CFG_NVRAM_SIZE 242 /* NVRAM size */
/*-----------------------------------------------------------------------
* I2C EEPROM (CAT24WC16) for environment
@@ -252,20 +252,20 @@
#define CFG_I2C_SLAVE 0x7F
#define CFG_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC08 */
-#define CFG_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
-/* mask of address bits that overflow into the "EEPROM chip address" */
+#define CFG_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
+/* mask of address bits that overflow into the "EEPROM chip address" */
#define CFG_I2C_EEPROM_ADDR_OVERFLOW 0x07
#define CFG_EEPROM_PAGE_WRITE_BITS 4 /* The Catalyst CAT24WC08 has */
/* 16 byte page write mode using*/
- /* last 4 bits of the address */
+ /* last 4 bits of the address */
#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
#define CFG_EEPROM_PAGE_WRITE_ENABLE
/*-----------------------------------------------------------------------
* Cache Configuration
*/
-#define CFG_DCACHE_SIZE 16384 /* For IBM 405 CPUs, older 405 ppc's */
- /* have only 8kB, 16kB is save here */
+#define CFG_DCACHE_SIZE 16384 /* For IBM 405 CPUs, older 405 ppc's */
+ /* have only 8kB, 16kB is save here */
#define CFG_CACHELINE_SIZE 32 /* ... */
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
@@ -283,49 +283,49 @@
* External Bus Controller (EBC) Setup
*/
-/* Memory Bank 0 (Flash Bank 0, NOR-FLASH) initialization */
-#define CFG_EBC_PB0AP 0x92015480
-/*#define CFG_EBC_PB0AP 0x08055880 /XXX* TWT=16,CSN=1,OEN=1,WBN=1,WBF=1,TH=4,SOR=1 */
-#define CFG_EBC_PB0CR 0xFFC5A000 /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
+/* Memory Bank 0 (Flash Bank 0, NOR-FLASH) initialization */
+#define CFG_EBC_PB0AP 0x92015480
+/*#define CFG_EBC_PB0AP 0x08055880 /XXX* TWT=16,CSN=1,OEN=1,WBN=1,WBF=1,TH=4,SOR=1 */
+#define CFG_EBC_PB0CR 0xFFC5A000 /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
-/* Memory Bank 1 (Flash Bank 1, NAND-FLASH) initialization */
-#define CFG_EBC_PB1AP 0x92015480
-#define CFG_EBC_PB1CR 0xF4018000 /* BAS=0xF40,BS=1MB,BU=R/W,BW=8bit */
+/* Memory Bank 1 (Flash Bank 1, NAND-FLASH) initialization */
+#define CFG_EBC_PB1AP 0x92015480
+#define CFG_EBC_PB1CR 0xF4018000 /* BAS=0xF40,BS=1MB,BU=R/W,BW=8bit */
-/* Memory Bank 2 (8 Bit Peripheral: CAN, UART, RTC) initialization */
-#define CFG_EBC_PB2AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
-#define CFG_EBC_PB2CR 0xF0018000 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */
+/* Memory Bank 2 (8 Bit Peripheral: CAN, UART, RTC) initialization */
+#define CFG_EBC_PB2AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
+#define CFG_EBC_PB2CR 0xF0018000 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */
-/* Memory Bank 3 (16 Bit Peripheral: FPGA internal, dig. IO) initialization */
-#define CFG_EBC_PB3AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
-#define CFG_EBC_PB3CR 0xF011A000 /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */
+/* Memory Bank 3 (16 Bit Peripheral: FPGA internal, dig. IO) initialization */
+#define CFG_EBC_PB3AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
+#define CFG_EBC_PB3CR 0xF011A000 /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */
-#define CAN_BA 0xF0000000 /* CAN Base Address */
-#define DUART0_BA 0xF0000400 /* DUART Base Address */
-#define DUART1_BA 0xF0000408 /* DUART Base Address */
-#define DUART2_BA 0xF0000410 /* DUART Base Address */
-#define DUART3_BA 0xF0000418 /* DUART Base Address */
-#define RTC_BA 0xF0000500 /* RTC Base Address */
-#define CFG_NAND_BASE 0xF4000000
+#define CAN_BA 0xF0000000 /* CAN Base Address */
+#define DUART0_BA 0xF0000400 /* DUART Base Address */
+#define DUART1_BA 0xF0000408 /* DUART Base Address */
+#define DUART2_BA 0xF0000410 /* DUART Base Address */
+#define DUART3_BA 0xF0000418 /* DUART Base Address */
+#define RTC_BA 0xF0000500 /* RTC Base Address */
+#define CFG_NAND_BASE 0xF4000000
/*-----------------------------------------------------------------------
* FPGA stuff
*/
-#define CFG_FPGA_SPARTAN2 1 /* using Xilinx Spartan 2 now */
-#define CFG_FPGA_MAX_SIZE 128*1024 /* 128kByte is enough for XC2S50E*/
+#define CFG_FPGA_SPARTAN2 1 /* using Xilinx Spartan 2 now */
+#define CFG_FPGA_MAX_SIZE 128*1024 /* 128kByte is enough for XC2S50E*/
/* FPGA program pin configuration */
-#define CFG_FPGA_PRG 0x04000000 /* FPGA program pin (ppc output) */
-#define CFG_FPGA_CLK 0x02000000 /* FPGA clk pin (ppc output) */
-#define CFG_FPGA_DATA 0x01000000 /* FPGA data pin (ppc output) */
-#define CFG_FPGA_INIT 0x00010000 /* FPGA init pin (ppc input) */
-#define CFG_FPGA_DONE 0x00008000 /* FPGA done pin (ppc input) */
+#define CFG_FPGA_PRG 0x04000000 /* FPGA program pin (ppc output) */
+#define CFG_FPGA_CLK 0x02000000 /* FPGA clk pin (ppc output) */
+#define CFG_FPGA_DATA 0x01000000 /* FPGA data pin (ppc output) */
+#define CFG_FPGA_INIT 0x00010000 /* FPGA init pin (ppc input) */
+#define CFG_FPGA_DONE 0x00008000 /* FPGA done pin (ppc input) */
/*-----------------------------------------------------------------------
* Definitions for initial stack pointer and data area (in data cache)
*/
/* use on chip memory ( OCM ) for temperary stack until sdram is tested */
-#define CFG_TEMP_STACK_OCM 1
+#define CFG_TEMP_STACK_OCM 1
/* On Chip Memory location */
#define CFG_OCM_DATA_ADDR 0xF8000000
@@ -335,13 +335,13 @@
#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
/*-----------------------------------------------------------------------
* Definitions for GPIO setup (PPC405EP specific)
*
- * GPIO0[0] - External Bus Controller BLAST output
- * GPIO0[1-9] - Instruction trace outputs -> GPIO
+ * GPIO0[0] - External Bus Controller BLAST output
+ * GPIO0[1-9] - Instruction trace outputs -> GPIO
* GPIO0[10-13] - External Bus Controller CS_1 - CS_4 outputs
* GPIO0[14-16] - External Bus Controller ABUS3-ABUS5 outputs -> GPIO
* GPIO0[17-23] - External Interrupts IRQ0 - IRQ6 inputs
@@ -349,15 +349,15 @@
* GPIO0[28-29] - UART1 data signal input/output
* GPIO0[30-31] - EMAC0 and EMAC1 reject packet inputs
*/
-#define CFG_GPIO0_OSRH 0x40000550
-#define CFG_GPIO0_OSRL 0x00000110
-#define CFG_GPIO0_ISR1H 0x00000000
-#define CFG_GPIO0_ISR1L 0x15555445
-#define CFG_GPIO0_TSRH 0x00000000
-#define CFG_GPIO0_TSRL 0x00000000
-#define CFG_GPIO0_TCR 0xF7FE0014
+#define CFG_GPIO0_OSRH 0x40000550
+#define CFG_GPIO0_OSRL 0x00000110
+#define CFG_GPIO0_ISR1H 0x00000000
+#define CFG_GPIO0_ISR1L 0x15555445
+#define CFG_GPIO0_TSRH 0x00000000
+#define CFG_GPIO0_TSRL 0x00000000
+#define CFG_GPIO0_TCR 0xF7FE0014
-#define CFG_DUART_RST (0x80000000 >> 14)
+#define CFG_DUART_RST (0x80000000 >> 14)
/*
* Internal Definitions
@@ -372,16 +372,16 @@
* This value will be set if iic boot eprom is disabled.
*/
#if 0
-#define PLLMR0_DEFAULT PLLMR0_266_133_66_33
-#define PLLMR1_DEFAULT PLLMR1_266_133_66_33
+#define PLLMR0_DEFAULT PLLMR0_266_133_66_33
+#define PLLMR1_DEFAULT PLLMR1_266_133_66_33
#endif
#if 1
-#define PLLMR0_DEFAULT PLLMR0_200_100_50_33
-#define PLLMR1_DEFAULT PLLMR1_200_100_50_33
+#define PLLMR0_DEFAULT PLLMR0_200_100_50_33
+#define PLLMR1_DEFAULT PLLMR1_200_100_50_33
#endif
#if 0
-#define PLLMR0_DEFAULT PLLMR0_133_66_66_33
-#define PLLMR1_DEFAULT PLLMR1_133_66_66_33
+#define PLLMR0_DEFAULT PLLMR0_133_66_66_33
+#define PLLMR1_DEFAULT PLLMR1_133_66_66_33
#endif
#endif /* __CONFIG_H */
diff --git a/include/configs/AmigaOneG3SE.h b/include/configs/AmigaOneG3SE.h
index 99b42e9..ea50f41 100644
--- a/include/configs/AmigaOneG3SE.h
+++ b/include/configs/AmigaOneG3SE.h
@@ -43,7 +43,7 @@
#define CONFIG_AMIGAONEG3SE 1
-#define CONFIG_BOARD_PRE_INIT 1
+#define CONFIG_BOARD_EARLY_INIT_F 1
#define CONFIG_MISC_INIT_R 1
#define CONFIG_VERY_BIG_RAM 1
diff --git a/include/configs/BMW.h b/include/configs/BMW.h
index edfd68f..050054d 100644
--- a/include/configs/BMW.h
+++ b/include/configs/BMW.h
@@ -45,7 +45,9 @@
#define CONFIG_MPC8245 1
#define CONFIG_BMW 1
-#define CONFIG_BCM570x 1 /* Use Broadcom BCM570x Ethernet Driver */
+#define CONFIG_MISC_INIT_F 1 /* Use misc_init_f() */
+
+#define CONFIG_BCM570x 1 /* Use Broadcom BCM570x Ethernet Driver */
#define CONFIG_TIGON3 1
#define CONFIG_CONS_INDEX 1
diff --git a/include/configs/BUBINGA405EP.h b/include/configs/BUBINGA405EP.h
index a485e4e..507cb75 100644
--- a/include/configs/BUBINGA405EP.h
+++ b/include/configs/BUBINGA405EP.h
@@ -42,7 +42,7 @@
#define CONFIG_4xx 1 /* ...member of PPC4xx family */
#define CONFIG_BUBINGA405EP 1 /* ...on a BUBINGA405EP board */
-#define CONFIG_BOARD_PRE_INIT 1 /* Call board_pre_init */
+#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
#define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */
diff --git a/include/configs/CANBT.h b/include/configs/CANBT.h
index 7aceb58..21bc441 100644
--- a/include/configs/CANBT.h
+++ b/include/configs/CANBT.h
@@ -34,12 +34,12 @@
*/
#define CONFIG_405CR 1 /* This is a PPC405CR CPU */
-#define CONFIG_4xx 1 /* ...member of PPC4xx family */
-#define CONFIG_CANBT 1 /* ...on a CANBT board */
+#define CONFIG_4xx 1 /* ...member of PPC4xx family */
+#define CONFIG_CANBT 1 /* ...on a CANBT board */
-#define CONFIG_BOARD_PRE_INIT 1 /* call board_pre_init() */
+#define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */
-#define CONFIG_SYS_CLK_FREQ 25000000 /* external frequency to pll */
+#define CONFIG_SYS_CLK_FREQ 25000000 /* external frequency to pll */
#define CONFIG_BAUDRATE 115200
#define CONFIG_BOOTDELAY 1 /* autoboot after 1 seconds */
@@ -52,13 +52,13 @@
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-#undef CONFIG_PCI_PNP /* no pci plug-and-play */
+#undef CONFIG_PCI_PNP /* no pci plug-and-play */
-#define CONFIG_PHY_ADDR 0 /* PHY address */
+#define CONFIG_PHY_ADDR 0 /* PHY address */
-#define CONFIG_COMMANDS (( CONFIG_CMD_DFL | \
- CFG_CMD_IRQ | \
- CFG_CMD_EEPROM ) & \
+#define CONFIG_COMMANDS (( CONFIG_CMD_DFL | \
+ CFG_CMD_IRQ | \
+ CFG_CMD_EEPROM ) & \
~CFG_CMD_NET)
/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
@@ -66,7 +66,7 @@
#undef CONFIG_WATCHDOG /* watchdog disabled */
-#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */
+#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */
/*
* Miscellaneous configurable options
@@ -74,30 +74,30 @@
#define CFG_LONGHELP /* undef to save memory */
#define CFG_PROMPT "=> " /* Monitor Command Prompt */
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
#endif
#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
#define CFG_MAXARGS 16 /* max number of command args */
#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
+#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-#define CFG_EXT_SERIAL_CLOCK 14745600 /* use external serial clock */
+#define CFG_EXT_SERIAL_CLOCK 14745600 /* use external serial clock */
/* The following table includes the supported baudrates */
-#define CFG_BAUDRATE_TABLE \
+#define CFG_BAUDRATE_TABLE \
{ 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \
57600, 115200, 230400, 460800, 921600 }
#define CFG_LOAD_ADDR 0x100000 /* default load address */
#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
@@ -127,44 +127,44 @@
#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
-#define CFG_FLASH_WORD_SIZE unsigned short /* flash word size (width) */
-#define CFG_FLASH_ADDR0 0x5555 /* 1st address for flash config cycles */
-#define CFG_FLASH_ADDR1 0x2AAA /* 2nd address for flash config cycles */
+#define CFG_FLASH_WORD_SIZE unsigned short /* flash word size (width) */
+#define CFG_FLASH_ADDR0 0x5555 /* 1st address for flash config cycles */
+#define CFG_FLASH_ADDR1 0x2AAA /* 2nd address for flash config cycles */
/*
* The following defines are added for buggy IOP480 byte interface.
* All other boards should use the standard values (CPCI405 etc.)
*/
-#define CFG_FLASH_READ0 0x0000 /* 0 is standard */
-#define CFG_FLASH_READ1 0x0001 /* 1 is standard */
-#define CFG_FLASH_READ2 0x0002 /* 2 is standard */
+#define CFG_FLASH_READ0 0x0000 /* 0 is standard */
+#define CFG_FLASH_READ1 0x0001 /* 1 is standard */
+#define CFG_FLASH_READ2 0x0002 /* 2 is standard */
-#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
+#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
#if 0 /* Use FLASH for environment variables */
-#define CFG_ENV_IS_IN_FLASH 1
-#define CFG_ENV_OFFSET 0x00010000 /* Offset of Environment Sector */
+#define CFG_ENV_IS_IN_FLASH 1
+#define CFG_ENV_OFFSET 0x00010000 /* Offset of Environment Sector */
#define CFG_ENV_SIZE 0x1000 /* Total Size of Environment Sector */
-#define CFG_ENV_SECT_SIZE 0x10000 /* see README - env sector total size */
+#define CFG_ENV_SECT_SIZE 0x10000 /* see README - env sector total size */
#else /* Use EEPROM for environment variables */
-#define CFG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
-#define CFG_ENV_OFFSET 0x000 /* environment starts at the beginning of the EEPROM */
-#define CFG_ENV_SIZE 0x400 /* 1024 bytes may be used for env vars */
+#define CFG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
+#define CFG_ENV_OFFSET 0x000 /* environment starts at the beginning of the EEPROM */
+#define CFG_ENV_SIZE 0x400 /* 1024 bytes may be used for env vars */
/* total size of a CAT24WC08 is 1024 bytes */
#endif
/*-----------------------------------------------------------------------
* I2C EEPROM (CAT24WC08) for environment
*/
-#define CONFIG_HARD_I2C /* I2C with hardware support */
+#define CONFIG_HARD_I2C /* I2C with hardware support */
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
#define CFG_I2C_SLAVE 0x7F
#define CFG_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC08 */
-#define CFG_I2C_EEPROM_ADDR_LEN 1 /* bytes of address */
+#define CFG_I2C_EEPROM_ADDR_LEN 1 /* bytes of address */
/* mask of address bits that overflow into the "EEPROM chip address" */
#define CFG_I2C_EEPROM_ADDR_OVERFLOW 0x07
@@ -190,26 +190,26 @@
* External Bus Controller (EBC) Setup
*/
-/* Memory Bank 0 (Flash Bank 0) initialization */
-#define CFG_EBC_PB0AP 0x92015480
-#define CFG_EBC_PB0CR 0xFFC5A000 /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
+/* Memory Bank 0 (Flash Bank 0) initialization */
+#define CFG_EBC_PB0AP 0x92015480
+#define CFG_EBC_PB0CR 0xFFC5A000 /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
-/* Memory Bank 1 (CAN/USB) initialization */
-#define CFG_EBC_PB1AP 0x010053C0 /* enable Ready, BEM=1 */
-#define CFG_EBC_PB1CR 0xF0018000 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */
+/* Memory Bank 1 (CAN/USB) initialization */
+#define CFG_EBC_PB1AP 0x010053C0 /* enable Ready, BEM=1 */
+#define CFG_EBC_PB1CR 0xF0018000 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */
-/* Memory Bank 2 (Misc-IO/LEDs) initialization */
-#define CFG_EBC_PB2AP 0x000004c0 /* no Ready, BEM=1 */
-#define CFG_EBC_PB2CR 0xF0118000 /* BAS=0xF01,BS=1MB,BU=R/W,BW=8bit */
+/* Memory Bank 2 (Misc-IO/LEDs) initialization */
+#define CFG_EBC_PB2AP 0x000004c0 /* no Ready, BEM=1 */
+#define CFG_EBC_PB2CR 0xF0118000 /* BAS=0xF01,BS=1MB,BU=R/W,BW=8bit */
-/* Memory Bank 3 (CAN Features) initialization */
-#define CFG_EBC_PB3AP 0x80000040 /* no Ready, BEM=1 */
-#define CFG_EBC_PB3CR 0xF021C000 /* BAS=0xF02,BS=1MB,BU=R/W,BW=32bit */
+/* Memory Bank 3 (CAN Features) initialization */
+#define CFG_EBC_PB3AP 0x80000040 /* no Ready, BEM=1 */
+#define CFG_EBC_PB3CR 0xF021C000 /* BAS=0xF02,BS=1MB,BU=R/W,BW=32bit */
/*-----------------------------------------------------------------------
* Definitions for initial stack pointer and data area (in RAM)
*/
-#define CFG_INIT_RAM_ADDR 0x00ef0000 /* inside of SDRAM */
+#define CFG_INIT_RAM_ADDR 0x00ef0000 /* inside of SDRAM */
#define CFG_INIT_RAM_END 0x0f00 /* End of used area in RAM */
#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
diff --git a/include/configs/CPCI405.h b/include/configs/CPCI405.h
index b877043..7c600d9 100644
--- a/include/configs/CPCI405.h
+++ b/include/configs/CPCI405.h
@@ -34,21 +34,21 @@
*/
#define CONFIG_405GP 1 /* This is a PPC405 CPU */
-#define CONFIG_4xx 1 /* ...member of PPC4xx family */
+#define CONFIG_4xx 1 /* ...member of PPC4xx family */
#define CONFIG_CPCI405 1 /* ...on a CPCI405 board */
-#define CONFIG_BOARD_PRE_INIT 1 /* call board_pre_init() */
+#define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */
-#define CONFIG_SYS_CLK_FREQ 33000000 /* external frequency to pll */
+#define CONFIG_SYS_CLK_FREQ 33000000 /* external frequency to pll */
#define CONFIG_BAUDRATE 9600
#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */
#if 0
-#define CONFIG_PREBOOT \
- "crc32 f0207004 ffc 0;" \
- "if cmp 0 f0207000 1;" \
- "then;echo Old CRC is correct;crc32 f0207004 ff4 f0207000;" \
+#define CONFIG_PREBOOT \
+ "crc32 f0207004 ffc 0;" \
+ "if cmp 0 f0207000 1;" \
+ "then;echo Old CRC is correct;crc32 f0207004 ff4 f0207000;" \
"else;echo Old CRC is bad;fi"
#endif
@@ -67,9 +67,9 @@
#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
#define CONFIG_MII 1 /* MII PHY management */
-#define CONFIG_PHY_ADDR 0 /* PHY address */
+#define CONFIG_PHY_ADDR 0 /* PHY address */
-#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT | \
+#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT | \
CONFIG_BOOTP_DNS | \
CONFIG_BOOTP_DNS2 | \
CONFIG_BOOTP_SEND_HOSTNAME )
@@ -81,7 +81,7 @@
CFG_CMD_IDE | \
CFG_CMD_ELF | \
CFG_CMD_MII | \
- CFG_CMD_EEPROM )
+ CFG_CMD_EEPROM )
#define CONFIG_MAC_PARTITION
#define CONFIG_DOS_PARTITION
@@ -89,9 +89,9 @@
/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
#include <cmd_confdefs.h>
-#undef CONFIG_WATCHDOG /* watchdog disabled */
+#undef CONFIG_WATCHDOG /* watchdog disabled */
-#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */
+#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */
/*
* Miscellaneous configurable options
@@ -101,38 +101,38 @@
#undef CFG_HUSH_PARSER /* use "hush" command parser */
#ifdef CFG_HUSH_PARSER
-#define CFG_PROMPT_HUSH_PS2 "> "
+#define CFG_PROMPT_HUSH_PS2 "> "
#endif
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
#endif
#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
#define CFG_MAXARGS 16 /* max number of command args */
#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_DEVICE_NULLDEV 1 /* include nulldev device */
+#define CFG_DEVICE_NULLDEV 1 /* include nulldev device */
-#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
+#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-#undef CFG_EXT_SERIAL_CLOCK /* no external serial clock used */
-#define CFG_IGNORE_405_UART_ERRATA_59 /* ignore ppc405gp errata #59 */
-#define CFG_BASE_BAUD 691200
+#undef CFG_EXT_SERIAL_CLOCK /* no external serial clock used */
+#define CFG_IGNORE_405_UART_ERRATA_59 /* ignore ppc405gp errata #59 */
+#define CFG_BASE_BAUD 691200
/* The following table includes the supported baudrates */
-#define CFG_BAUDRATE_TABLE \
+#define CFG_BAUDRATE_TABLE \
{ 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \
57600, 115200, 230400, 460800, 921600 }
#define CFG_LOAD_ADDR 0x100000 /* default load address */
#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
@@ -140,46 +140,46 @@
* PCI stuff
*-----------------------------------------------------------------------
*/
-#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */
-#define PCI_HOST_FORCE 1 /* configure as pci host */
-#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
+#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */
+#define PCI_HOST_FORCE 1 /* configure as pci host */
+#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
-#define CONFIG_PCI /* include pci support */
-#define CONFIG_PCI_HOST PCI_HOST_AUTO /* select pci host function */
-#define CONFIG_PCI_PNP /* do pci plug-and-play */
- /* resource configuration */
+#define CONFIG_PCI /* include pci support */
+#define CONFIG_PCI_HOST PCI_HOST_AUTO /* select pci host function */
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
+ /* resource configuration */
-#define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */
+#define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */
-#define CONFIG_PCI_BOOTDELAY 0 /* enable pci bootdelay variable*/
+#define CONFIG_PCI_BOOTDELAY 0 /* enable pci bootdelay variable*/
-#define CFG_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */
-#define CFG_PCI_SUBSYS_DEVICEID 0x0405 /* PCI Device ID: CPCI-405 */
-#define CFG_PCI_SUBSYS_DEVICEID2 0x0406 /* PCI Device ID: CPCI-405-A */
-#define CFG_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/
-#define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */
-#define CFG_PCI_PTM1MS 0xfc000001 /* 64MB, enable hard-wired to 1 */
-#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
-#define CFG_PCI_PTM2LA 0xffc00000 /* point to flash */
-#define CFG_PCI_PTM2MS 0xffc00001 /* 4MB, enable */
-#define CFG_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */
+#define CFG_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */
+#define CFG_PCI_SUBSYS_DEVICEID 0x0405 /* PCI Device ID: CPCI-405 */
+#define CFG_PCI_SUBSYS_DEVICEID2 0x0406 /* PCI Device ID: CPCI-405-A */
+#define CFG_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/
+#define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */
+#define CFG_PCI_PTM1MS 0xfc000001 /* 64MB, enable hard-wired to 1 */
+#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
+#define CFG_PCI_PTM2LA 0xffc00000 /* point to flash */
+#define CFG_PCI_PTM2MS 0xffc00001 /* 4MB, enable */
+#define CFG_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */
/*-----------------------------------------------------------------------
* IDE/ATA stuff
*-----------------------------------------------------------------------
*/
-#undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */
-#undef CONFIG_IDE_LED /* no led for ide supported */
-#undef CONFIG_IDE_RESET /* no reset for ide supported */
+#undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */
+#undef CONFIG_IDE_LED /* no led for ide supported */
+#undef CONFIG_IDE_RESET /* no reset for ide supported */
-#define CFG_IDE_MAXBUS 1 /* max. 1 IDE busses */
-#define CFG_IDE_MAXDEVICE (CFG_IDE_MAXBUS*1) /* max. 1 drives per IDE bus */
+#define CFG_IDE_MAXBUS 1 /* max. 1 IDE busses */
+#define CFG_IDE_MAXDEVICE (CFG_IDE_MAXBUS*1) /* max. 1 drives per IDE bus */
-#define CFG_ATA_BASE_ADDR 0xF0100000
-#define CFG_ATA_IDE0_OFFSET 0x0000
+#define CFG_ATA_BASE_ADDR 0xF0100000
+#define CFG_ATA_IDE0_OFFSET 0x0000
#define CFG_ATA_DATA_OFFSET 0x0000 /* Offset for data I/O */
-#define CFG_ATA_REG_OFFSET 0x0000 /* Offset for normal register accesses */
+#define CFG_ATA_REG_OFFSET 0x0000 /* Offset for normal register accesses */
#define CFG_ATA_ALT_OFFSET 0x0000 /* Offset for alternate registers */
/*-----------------------------------------------------------------------
@@ -208,18 +208,18 @@
#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
-#define CFG_FLASH_WORD_SIZE unsigned short /* flash word size (width) */
-#define CFG_FLASH_ADDR0 0x5555 /* 1st address for flash config cycles */
-#define CFG_FLASH_ADDR1 0x2AAA /* 2nd address for flash config cycles */
+#define CFG_FLASH_WORD_SIZE unsigned short /* flash word size (width) */
+#define CFG_FLASH_ADDR0 0x5555 /* 1st address for flash config cycles */
+#define CFG_FLASH_ADDR1 0x2AAA /* 2nd address for flash config cycles */
/*
* The following defines are added for buggy IOP480 byte interface.
* All other boards should use the standard values (CPCI405 etc.)
*/
-#define CFG_FLASH_READ0 0x0000 /* 0 is standard */
-#define CFG_FLASH_READ1 0x0001 /* 1 is standard */
-#define CFG_FLASH_READ2 0x0002 /* 2 is standard */
+#define CFG_FLASH_READ0 0x0000 /* 0 is standard */
+#define CFG_FLASH_READ1 0x0001 /* 1 is standard */
+#define CFG_FLASH_READ2 0x0002 /* 2 is standard */
-#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
+#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
#if 1 /* Use NVRAM for environment variables */
/*-----------------------------------------------------------------------
@@ -235,9 +235,9 @@
#else /* Use EEPROM for environment variables */
-#define CFG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
-#define CFG_ENV_OFFSET 0x000 /* environment starts at the beginning of the EEPROM */
-#define CFG_ENV_SIZE 0x200 /* 512 bytes may be used for env vars */
+#define CFG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
+#define CFG_ENV_OFFSET 0x000 /* environment starts at the beginning of the EEPROM */
+#define CFG_ENV_SIZE 0x200 /* 512 bytes may be used for env vars */
/* total size of a CAT24WC08 is 1024 bytes */
#endif
@@ -249,12 +249,12 @@
#define CFG_I2C_SLAVE 0x7F
#define CFG_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC08 */
-#define CFG_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
-/* mask of address bits that overflow into the "EEPROM chip address" */
+#define CFG_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
+/* mask of address bits that overflow into the "EEPROM chip address" */
#define CFG_I2C_EEPROM_ADDR_OVERFLOW 0x07
#define CFG_EEPROM_PAGE_WRITE_BITS 4 /* The Catalyst CAT24WC08 has */
/* 16 byte page write mode using*/
- /* last 4 bits of the address */
+ /* last 4 bits of the address */
#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
#define CFG_EEPROM_PAGE_WRITE_ENABLE
@@ -280,55 +280,55 @@
* External Bus Controller (EBC) Setup
*/
-/* Memory Bank 0 (Flash Bank 0) initialization */
-#define CFG_EBC_PB0AP 0x92015480
-#define CFG_EBC_PB0CR 0xFFC5A000 /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
+/* Memory Bank 0 (Flash Bank 0) initialization */
+#define CFG_EBC_PB0AP 0x92015480
+#define CFG_EBC_PB0CR 0xFFC5A000 /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
-/* Memory Bank 1 (Flash Bank 1) initialization */
-#define CFG_EBC_PB1AP 0x92015480
-#define CFG_EBC_PB1CR 0xFF85A000 /* BAS=0xFF8,BS=4MB,BU=R/W,BW=16bit */
+/* Memory Bank 1 (Flash Bank 1) initialization */
+#define CFG_EBC_PB1AP 0x92015480
+#define CFG_EBC_PB1CR 0xFF85A000 /* BAS=0xFF8,BS=4MB,BU=R/W,BW=16bit */
-/* Memory Bank 2 (CAN0, 1, 2, Codeswitch) initialization */
-#define CFG_EBC_PB2AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
-#define CFG_EBC_PB2CR 0xF0018000 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */
+/* Memory Bank 2 (CAN0, 1, 2, Codeswitch) initialization */
+#define CFG_EBC_PB2AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
+#define CFG_EBC_PB2CR 0xF0018000 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */
-/* Memory Bank 3 (CompactFlash IDE) initialization */
-#define CFG_EBC_PB3AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
-#define CFG_EBC_PB3CR 0xF011A000 /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */
+/* Memory Bank 3 (CompactFlash IDE) initialization */
+#define CFG_EBC_PB3AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
+#define CFG_EBC_PB3CR 0xF011A000 /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */
-/* Memory Bank 4 (NVRAM) initialization */
-#define CFG_EBC_PB4AP 0x01005280 /* TWT=2,WBN=1,WBF=1,TH=1,SOR=1 */
-#define CFG_EBC_PB4CR 0xF0218000 /* BAS=0xF02,BS=1MB,BU=R/W,BW=8bit */
+/* Memory Bank 4 (NVRAM) initialization */
+#define CFG_EBC_PB4AP 0x01005280 /* TWT=2,WBN=1,WBF=1,TH=1,SOR=1 */
+#define CFG_EBC_PB4CR 0xF0218000 /* BAS=0xF02,BS=1MB,BU=R/W,BW=8bit */
-/* Memory Bank 5 (Quart) initialization */
-#define CFG_EBC_PB5AP 0x04005B80 /* TWT=8,WBN=1,WBF=1,TH=5,RE=1,SOR=1*/
-#define CFG_EBC_PB5CR 0xF0318000 /* BAS=0xF03,BS=1MB,BU=R/W,BW=8bit */
+/* Memory Bank 5 (Quart) initialization */
+#define CFG_EBC_PB5AP 0x04005B80 /* TWT=8,WBN=1,WBF=1,TH=5,RE=1,SOR=1*/
+#define CFG_EBC_PB5CR 0xF0318000 /* BAS=0xF03,BS=1MB,BU=R/W,BW=8bit */
/*-----------------------------------------------------------------------
* FPGA stuff
*/
/* FPGA program pin configuration */
-#define CFG_FPGA_PRG 0x04000000 /* FPGA program pin (ppc output) */
-#define CFG_FPGA_CLK 0x02000000 /* FPGA clk pin (ppc output) */
-#define CFG_FPGA_DATA 0x01000000 /* FPGA data pin (ppc output) */
-#define CFG_FPGA_INIT 0x00400000 /* FPGA init pin (ppc input) */
-#define CFG_FPGA_DONE 0x00800000 /* FPGA done pin (ppc input) */
+#define CFG_FPGA_PRG 0x04000000 /* FPGA program pin (ppc output) */
+#define CFG_FPGA_CLK 0x02000000 /* FPGA clk pin (ppc output) */
+#define CFG_FPGA_DATA 0x01000000 /* FPGA data pin (ppc output) */
+#define CFG_FPGA_INIT 0x00400000 /* FPGA init pin (ppc input) */
+#define CFG_FPGA_DONE 0x00800000 /* FPGA done pin (ppc input) */
/*-----------------------------------------------------------------------
* Definitions for initial stack pointer and data area (in data cache)
*/
#if 1 /* test-only */
-#define CFG_INIT_DCACHE_CS 7 /* use cs # 7 for data cache memory */
+#define CFG_INIT_DCACHE_CS 7 /* use cs # 7 for data cache memory */
-#define CFG_INIT_RAM_ADDR 0x40000000 /* use data cache */
+#define CFG_INIT_RAM_ADDR 0x40000000 /* use data cache */
#else
-#define CFG_INIT_RAM_ADDR 0x00df0000 /* inside of SDRAM */
+#define CFG_INIT_RAM_ADDR 0x00df0000 /* inside of SDRAM */
#endif
-#define CFG_INIT_RAM_END 0x2000 /* End of used area in RAM */
+#define CFG_INIT_RAM_END 0x2000 /* End of used area in RAM */
#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
/*
diff --git a/include/configs/CPCI4052.h b/include/configs/CPCI4052.h
index dd2fa7f..6ee5698 100644
--- a/include/configs/CPCI4052.h
+++ b/include/configs/CPCI4052.h
@@ -34,22 +34,22 @@
*/
#define CONFIG_405GP 1 /* This is a PPC405 CPU */
-#define CONFIG_4xx 1 /* ...member of PPC4xx family */
+#define CONFIG_4xx 1 /* ...member of PPC4xx family */
#define CONFIG_CPCI405 1 /* ...on a CPCI405 board */
-#define CONFIG_CPCI405_VER2 1 /* ...version 2 */
+#define CONFIG_CPCI405_VER2 1 /* ...version 2 */
-#define CONFIG_BOARD_PRE_INIT 1 /* call board_pre_init() */
+#define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */
-#define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */
+#define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */
#define CONFIG_BAUDRATE 9600
#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */
#if 0
-#define CONFIG_PREBOOT \
- "crc32 f0207004 ffc 0;" \
- "if cmp 0 f0207000 1;" \
- "then;echo Old CRC is correct;crc32 f0207004 ff4 f0207000;" \
+#define CONFIG_PREBOOT \
+ "crc32 f0207004 ffc 0;" \
+ "if cmp 0 f0207000 1;" \
+ "then;echo Old CRC is correct;crc32 f0207004 ff4 f0207000;" \
"else;echo Old CRC is bad;fi"
#endif
@@ -68,11 +68,11 @@
#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
#define CONFIG_MII 1 /* MII PHY management */
-#define CONFIG_PHY_ADDR 0 /* PHY address */
+#define CONFIG_PHY_ADDR 0 /* PHY address */
#define CONFIG_RTC_M48T35A 1 /* ST Electronics M48 timekeeper */
-#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT | \
+#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT | \
CONFIG_BOOTP_DNS | \
CONFIG_BOOTP_DNS2 | \
CONFIG_BOOTP_SEND_HOSTNAME )
@@ -88,7 +88,7 @@
CFG_CMD_I2C | \
CFG_CMD_MII | \
CFG_CMD_PING | \
- CFG_CMD_EEPROM )
+ CFG_CMD_EEPROM )
#define CONFIG_MAC_PARTITION
#define CONFIG_DOS_PARTITION
@@ -96,9 +96,9 @@
/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
#include <cmd_confdefs.h>
-#undef CONFIG_WATCHDOG /* watchdog disabled */
+#undef CONFIG_WATCHDOG /* watchdog disabled */
-#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */
+#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */
/*
* Miscellaneous configurable options
@@ -108,89 +108,89 @@
#undef CFG_HUSH_PARSER /* use "hush" command parser */
#ifdef CFG_HUSH_PARSER
-#define CFG_PROMPT_HUSH_PS2 "> "
+#define CFG_PROMPT_HUSH_PS2 "> "
#endif
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
#endif
#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
#define CFG_MAXARGS 16 /* max number of command args */
#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_DEVICE_NULLDEV 1 /* include nulldev device */
+#define CFG_DEVICE_NULLDEV 1 /* include nulldev device */
-#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
+#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-#undef CFG_EXT_SERIAL_CLOCK /* no external serial clock used */
-#define CFG_IGNORE_405_UART_ERRATA_59 /* ignore ppc405gp errata #59 */
-#define CFG_BASE_BAUD 691200
+#undef CFG_EXT_SERIAL_CLOCK /* no external serial clock used */
+#define CFG_IGNORE_405_UART_ERRATA_59 /* ignore ppc405gp errata #59 */
+#define CFG_BASE_BAUD 691200
/* The following table includes the supported baudrates */
-#define CFG_BAUDRATE_TABLE \
+#define CFG_BAUDRATE_TABLE \
{ 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \
57600, 115200, 230400, 460800, 921600 }
#define CFG_LOAD_ADDR 0x100000 /* default load address */
#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
+#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
-#define CFG_RX_ETH_BUFFER 16 /* use 16 rx buffer on 405 emac */
+#define CFG_RX_ETH_BUFFER 16 /* use 16 rx buffer on 405 emac */
/*-----------------------------------------------------------------------
* PCI stuff
*-----------------------------------------------------------------------
*/
-#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */
-#define PCI_HOST_FORCE 1 /* configure as pci host */
-#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
+#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */
+#define PCI_HOST_FORCE 1 /* configure as pci host */
+#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
-#define CONFIG_PCI /* include pci support */
-#define CONFIG_PCI_HOST PCI_HOST_AUTO /* select pci host function */
-#define CONFIG_PCI_PNP /* do pci plug-and-play */
- /* resource configuration */
+#define CONFIG_PCI /* include pci support */
+#define CONFIG_PCI_HOST PCI_HOST_AUTO /* select pci host function */
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
+ /* resource configuration */
-#define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */
+#define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */
-#define CONFIG_PCI_BOOTDELAY 0 /* enable pci bootdelay variable*/
+#define CONFIG_PCI_BOOTDELAY 0 /* enable pci bootdelay variable*/
-#define CFG_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */
-#define CFG_PCI_SUBSYS_DEVICEID 0x0405 /* PCI Device ID: CPCI-405 */
-#define CFG_PCI_SUBSYS_DEVICEID2 0x0406 /* PCI Device ID: CPCI-405-A */
-#define CFG_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/
-#define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */
-#define CFG_PCI_PTM1MS 0xfc000001 /* 64MB, enable hard-wired to 1 */
-#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
-#define CFG_PCI_PTM2LA 0xffc00000 /* point to flash */
-#define CFG_PCI_PTM2MS 0xffc00001 /* 4MB, enable */
-#define CFG_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */
+#define CFG_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */
+#define CFG_PCI_SUBSYS_DEVICEID 0x0405 /* PCI Device ID: CPCI-405 */
+#define CFG_PCI_SUBSYS_DEVICEID2 0x0406 /* PCI Device ID: CPCI-405-A */
+#define CFG_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/
+#define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */
+#define CFG_PCI_PTM1MS 0xfc000001 /* 64MB, enable hard-wired to 1 */
+#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
+#define CFG_PCI_PTM2LA 0xffc00000 /* point to flash */
+#define CFG_PCI_PTM2MS 0xffc00001 /* 4MB, enable */
+#define CFG_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */
/*-----------------------------------------------------------------------
* IDE/ATA stuff
*-----------------------------------------------------------------------
*/
-#undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */
-#undef CONFIG_IDE_LED /* no led for ide supported */
+#undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */
+#undef CONFIG_IDE_LED /* no led for ide supported */
#define CONFIG_IDE_RESET 1 /* reset for ide supported */
-#define CFG_IDE_MAXBUS 1 /* max. 1 IDE busses */
-#define CFG_IDE_MAXDEVICE (CFG_IDE_MAXBUS*1) /* max. 1 drives per IDE bus */
+#define CFG_IDE_MAXBUS 1 /* max. 1 IDE busses */
+#define CFG_IDE_MAXDEVICE (CFG_IDE_MAXBUS*1) /* max. 1 drives per IDE bus */
-#define CFG_ATA_BASE_ADDR 0xF0100000
-#define CFG_ATA_IDE0_OFFSET 0x0000
+#define CFG_ATA_BASE_ADDR 0xF0100000
+#define CFG_ATA_IDE0_OFFSET 0x0000
#define CFG_ATA_DATA_OFFSET 0x0000 /* Offset for data I/O */
-#define CFG_ATA_REG_OFFSET 0x0000 /* Offset for normal register accesses */
+#define CFG_ATA_REG_OFFSET 0x0000 /* Offset for normal register accesses */
#define CFG_ATA_ALT_OFFSET 0x0000 /* Offset for alternate registers */
/*-----------------------------------------------------------------------
@@ -219,21 +219,21 @@
#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
-#define CFG_FLASH_WORD_SIZE unsigned short /* flash word size (width) */
-#define CFG_FLASH_ADDR0 0x5555 /* 1st address for flash config cycles */
-#define CFG_FLASH_ADDR1 0x2AAA /* 2nd address for flash config cycles */
+#define CFG_FLASH_WORD_SIZE unsigned short /* flash word size (width) */
+#define CFG_FLASH_ADDR0 0x5555 /* 1st address for flash config cycles */
+#define CFG_FLASH_ADDR1 0x2AAA /* 2nd address for flash config cycles */
/*
* The following defines are added for buggy IOP480 byte interface.
* All other boards should use the standard values (CPCI405 etc.)
*/
-#define CFG_FLASH_READ0 0x0000 /* 0 is standard */
-#define CFG_FLASH_READ1 0x0001 /* 1 is standard */
-#define CFG_FLASH_READ2 0x0002 /* 2 is standard */
+#define CFG_FLASH_READ0 0x0000 /* 0 is standard */
+#define CFG_FLASH_READ1 0x0001 /* 1 is standard */
+#define CFG_FLASH_READ2 0x0002 /* 2 is standard */
-#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
+#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
-#define CFG_JFFS2_FIRST_BANK 0 /* use for JFFS2 */
-#define CFG_JFFS2_NUM_BANKS 1 /* ! second bank contains U-Boot */
+#define CFG_JFFS2_FIRST_BANK 0 /* use for JFFS2 */
+#define CFG_JFFS2_NUM_BANKS 1 /* ! second bank contains U-Boot */
#if 0 /* Use NVRAM for environment variables */
/*-----------------------------------------------------------------------
@@ -246,9 +246,9 @@
#else /* Use EEPROM for environment variables */
-#define CFG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
-#define CFG_ENV_OFFSET 0x000 /* environment starts at the beginning of the EEPROM */
-#define CFG_ENV_SIZE 0x800 /* 2048 bytes may be used for env vars*/
+#define CFG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
+#define CFG_ENV_OFFSET 0x000 /* environment starts at the beginning of the EEPROM */
+#define CFG_ENV_SIZE 0x800 /* 2048 bytes may be used for env vars*/
/* total size of a CAT24WC16 is 2048 bytes */
#endif
@@ -264,20 +264,20 @@
#define CFG_I2C_SLAVE 0x7F
#define CFG_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC08 */
-#define CFG_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
-/* mask of address bits that overflow into the "EEPROM chip address" */
+#define CFG_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
+/* mask of address bits that overflow into the "EEPROM chip address" */
#define CFG_I2C_EEPROM_ADDR_OVERFLOW 0x07
#define CFG_EEPROM_PAGE_WRITE_BITS 4 /* The Catalyst CAT24WC08 has */
/* 16 byte page write mode using*/
- /* last 4 bits of the address */
+ /* last 4 bits of the address */
#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
#define CFG_EEPROM_PAGE_WRITE_ENABLE
/*-----------------------------------------------------------------------
* Cache Configuration
*/
-#define CFG_DCACHE_SIZE 16384 /* For IBM 405 CPUs, older 405 ppc's */
- /* have only 8kB, 16kB is save here */
+#define CFG_DCACHE_SIZE 16384 /* For IBM 405 CPUs, older 405 ppc's */
+ /* have only 8kB, 16kB is save here */
#define CFG_CACHELINE_SIZE 32 /* ... */
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
@@ -296,89 +296,89 @@
* External Bus Controller (EBC) Setup
*/
-/* Memory Bank 0 (Flash Bank 0) initialization */
-#define CFG_EBC_PB0AP 0x92015480
-#define CFG_EBC_PB0CR 0xFFC5A000 /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
+/* Memory Bank 0 (Flash Bank 0) initialization */
+#define CFG_EBC_PB0AP 0x92015480
+#define CFG_EBC_PB0CR 0xFFC5A000 /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
-/* Memory Bank 1 (Flash Bank 1) initialization */
-#define CFG_EBC_PB1AP 0x92015480
-#define CFG_EBC_PB1CR 0xFF85A000 /* BAS=0xFF8,BS=4MB,BU=R/W,BW=16bit */
+/* Memory Bank 1 (Flash Bank 1) initialization */
+#define CFG_EBC_PB1AP 0x92015480
+#define CFG_EBC_PB1CR 0xFF85A000 /* BAS=0xFF8,BS=4MB,BU=R/W,BW=16bit */
-/* Memory Bank 2 (CAN0, 1) initialization */
-#define CFG_EBC_PB2AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
-#define CFG_EBC_PB2CR 0xF0018000 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */
-#define CFG_LED_ADDR 0xF0000380
+/* Memory Bank 2 (CAN0, 1) initialization */
+#define CFG_EBC_PB2AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
+#define CFG_EBC_PB2CR 0xF0018000 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */
+#define CFG_LED_ADDR 0xF0000380
-/* Memory Bank 3 (CompactFlash IDE) initialization */
-#define CFG_EBC_PB3AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
-#define CFG_EBC_PB3CR 0xF011A000 /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */
+/* Memory Bank 3 (CompactFlash IDE) initialization */
+#define CFG_EBC_PB3AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
+#define CFG_EBC_PB3CR 0xF011A000 /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */
-/* Memory Bank 4 (NVRAM/RTC) initialization */
-/*#define CFG_EBC_PB4AP 0x01805280 / * TWT=3,WBN=1,WBF=1,TH=1,SOR=1 */
-#define CFG_EBC_PB4AP 0x01805680 /* TWT=3,WBN=1,WBF=1,TH=3,SOR=1 */
-#define CFG_EBC_PB4CR 0xF0218000 /* BAS=0xF02,BS=1MB,BU=R/W,BW=8bit */
+/* Memory Bank 4 (NVRAM/RTC) initialization */
+/*#define CFG_EBC_PB4AP 0x01805280 / * TWT=3,WBN=1,WBF=1,TH=1,SOR=1 */
+#define CFG_EBC_PB4AP 0x01805680 /* TWT=3,WBN=1,WBF=1,TH=3,SOR=1 */
+#define CFG_EBC_PB4CR 0xF0218000 /* BAS=0xF02,BS=1MB,BU=R/W,BW=8bit */
-/* Memory Bank 5 (optional Quart) initialization */
-#define CFG_EBC_PB5AP 0x04005B80 /* TWT=8,WBN=1,WBF=1,TH=5,RE=1,SOR=1*/
-#define CFG_EBC_PB5CR 0xF0318000 /* BAS=0xF03,BS=1MB,BU=R/W,BW=8bit */
+/* Memory Bank 5 (optional Quart) initialization */
+#define CFG_EBC_PB5AP 0x04005B80 /* TWT=8,WBN=1,WBF=1,TH=5,RE=1,SOR=1*/
+#define CFG_EBC_PB5CR 0xF0318000 /* BAS=0xF03,BS=1MB,BU=R/W,BW=8bit */
-/* Memory Bank 6 (FPGA internal) initialization */
-#define CFG_EBC_PB6AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
-#define CFG_EBC_PB6CR 0xF041A000 /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */
-#define CFG_FPGA_BASE_ADDR 0xF0400000
+/* Memory Bank 6 (FPGA internal) initialization */
+#define CFG_EBC_PB6AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
+#define CFG_EBC_PB6CR 0xF041A000 /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */
+#define CFG_FPGA_BASE_ADDR 0xF0400000
/*-----------------------------------------------------------------------
* FPGA stuff
*/
/* FPGA internal regs */
-#define CFG_FPGA_MODE 0x00
-#define CFG_FPGA_STATUS 0x02
-#define CFG_FPGA_TS 0x04
-#define CFG_FPGA_TS_LOW 0x06
-#define CFG_FPGA_TS_CAP0 0x10
-#define CFG_FPGA_TS_CAP0_LOW 0x12
-#define CFG_FPGA_TS_CAP1 0x14
-#define CFG_FPGA_TS_CAP1_LOW 0x16
-#define CFG_FPGA_TS_CAP2 0x18
-#define CFG_FPGA_TS_CAP2_LOW 0x1a
-#define CFG_FPGA_TS_CAP3 0x1c
-#define CFG_FPGA_TS_CAP3_LOW 0x1e
+#define CFG_FPGA_MODE 0x00
+#define CFG_FPGA_STATUS 0x02
+#define CFG_FPGA_TS 0x04
+#define CFG_FPGA_TS_LOW 0x06
+#define CFG_FPGA_TS_CAP0 0x10
+#define CFG_FPGA_TS_CAP0_LOW 0x12
+#define CFG_FPGA_TS_CAP1 0x14
+#define CFG_FPGA_TS_CAP1_LOW 0x16
+#define CFG_FPGA_TS_CAP2 0x18
+#define CFG_FPGA_TS_CAP2_LOW 0x1a
+#define CFG_FPGA_TS_CAP3 0x1c
+#define CFG_FPGA_TS_CAP3_LOW 0x1e
/* FPGA Mode Reg */
-#define CFG_FPGA_MODE_CF_RESET 0x0001
+#define CFG_FPGA_MODE_CF_RESET 0x0001
#define CFG_FPGA_MODE_DUART_RESET 0x0002
#define CFG_FPGA_MODE_ENABLE_OUTPUT 0x0004 /* only set on CPCI-405 Ver 3 */
#define CFG_FPGA_MODE_TS_IRQ_ENABLE 0x0100
#define CFG_FPGA_MODE_TS_IRQ_CLEAR 0x1000
-#define CFG_FPGA_MODE_TS_CLEAR 0x2000
+#define CFG_FPGA_MODE_TS_CLEAR 0x2000
/* FPGA Status Reg */
-#define CFG_FPGA_STATUS_DIP0 0x0001
-#define CFG_FPGA_STATUS_DIP1 0x0002
-#define CFG_FPGA_STATUS_DIP2 0x0004
-#define CFG_FPGA_STATUS_FLASH 0x0008
-#define CFG_FPGA_STATUS_TS_IRQ 0x1000
+#define CFG_FPGA_STATUS_DIP0 0x0001
+#define CFG_FPGA_STATUS_DIP1 0x0002
+#define CFG_FPGA_STATUS_DIP2 0x0004
+#define CFG_FPGA_STATUS_FLASH 0x0008
+#define CFG_FPGA_STATUS_TS_IRQ 0x1000
-#define CFG_FPGA_SPARTAN2 1 /* using Xilinx Spartan 2 now */
-#define CFG_FPGA_MAX_SIZE 32*1024 /* 32kByte is enough for XC2S15 */
+#define CFG_FPGA_SPARTAN2 1 /* using Xilinx Spartan 2 now */
+#define CFG_FPGA_MAX_SIZE 32*1024 /* 32kByte is enough for XC2S15 */
/* FPGA program pin configuration */
-#define CFG_FPGA_PRG 0x04000000 /* FPGA program pin (ppc output) */
-#define CFG_FPGA_CLK 0x02000000 /* FPGA clk pin (ppc output) */
-#define CFG_FPGA_DATA 0x01000000 /* FPGA data pin (ppc output) */
-#define CFG_FPGA_INIT 0x00010000 /* FPGA init pin (ppc input) */
-#define CFG_FPGA_DONE 0x00008000 /* FPGA done pin (ppc input) */
+#define CFG_FPGA_PRG 0x04000000 /* FPGA program pin (ppc output) */
+#define CFG_FPGA_CLK 0x02000000 /* FPGA clk pin (ppc output) */
+#define CFG_FPGA_DATA 0x01000000 /* FPGA data pin (ppc output) */
+#define CFG_FPGA_INIT 0x00010000 /* FPGA init pin (ppc input) */
+#define CFG_FPGA_DONE 0x00008000 /* FPGA done pin (ppc input) */
/*-----------------------------------------------------------------------
* Definitions for initial stack pointer and data area (in data cache)
*/
-#define CFG_INIT_DCACHE_CS 7 /* use cs # 7 for data cache memory */
+#define CFG_INIT_DCACHE_CS 7 /* use cs # 7 for data cache memory */
-#define CFG_INIT_RAM_ADDR 0x40000000 /* use data cache */
-#define CFG_INIT_RAM_END 0x2000 /* End of used area in RAM */
+#define CFG_INIT_RAM_ADDR 0x40000000 /* use data cache */
+#define CFG_INIT_RAM_END 0x2000 /* End of used area in RAM */
#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
/*
diff --git a/include/configs/CPCI405AB.h b/include/configs/CPCI405AB.h
index 492fe49..3c94ebc 100644
--- a/include/configs/CPCI405AB.h
+++ b/include/configs/CPCI405AB.h
@@ -34,38 +34,38 @@
*/
#define CONFIG_405GP 1 /* This is a PPC405 CPU */
-#define CONFIG_4xx 1 /* ...member of PPC4xx family */
+#define CONFIG_4xx 1 /* ...member of PPC4xx family */
#define CONFIG_CPCI405 1 /* ...on a CPCI405 board */
-#define CONFIG_CPCI405_VER2 1 /* ...version 2 */
-#define CONFIG_CPCI405AB 1 /* ...and special AB version */
+#define CONFIG_CPCI405_VER2 1 /* ...version 2 */
+#define CONFIG_CPCI405AB 1 /* ...and special AB version */
-#define CONFIG_BOARD_PRE_INIT 1 /* call board_pre_init() */
+#define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */
-#define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */
+#define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */
#define CONFIG_BAUDRATE 9600
#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */
#if 0
-#define CONFIG_PREBOOT \
- "crc32 f0207004 ffc 0;" \
- "if cmp 0 f0207000 1;" \
- "then;echo Old CRC is correct;crc32 f0207004 ff4 f0207000;" \
+#define CONFIG_PREBOOT \
+ "crc32 f0207004 ffc 0;" \
+ "if cmp 0 f0207000 1;" \
+ "then;echo Old CRC is correct;crc32 f0207004 ff4 f0207000;" \
"else;echo Old CRC is bad;fi"
#endif
#undef CONFIG_BOOTARGS
-#define CONFIG_BOOTCOMMAND "bootm 100000" /* default boot command */
+#define CONFIG_BOOTCOMMAND "bootm 100000" /* default boot command */
-#undef CONFIG_LOADS_ECHO /* echo on for serial download */
+#undef CONFIG_LOADS_ECHO /* echo on for serial download */
#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
#define CONFIG_MII 1 /* MII PHY management */
-#define CONFIG_PHY_ADDR 0 /* PHY address */
+#define CONFIG_PHY_ADDR 0 /* PHY address */
#define CONFIG_RTC_M48T35A 1 /* ST Electronics M48 timekeeper */
-#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT | \
+#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT | \
CONFIG_BOOTP_DNS | \
CONFIG_BOOTP_DNS2 | \
CONFIG_BOOTP_SEND_HOSTNAME )
@@ -81,7 +81,7 @@
CFG_CMD_I2C | \
CFG_CMD_MII | \
CFG_CMD_PING | \
- CFG_CMD_EEPROM )
+ CFG_CMD_EEPROM )
#define CONFIG_MAC_PARTITION
#define CONFIG_DOS_PARTITION
@@ -89,9 +89,9 @@
/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
#include <cmd_confdefs.h>
-#undef CONFIG_WATCHDOG /* watchdog disabled */
+#undef CONFIG_WATCHDOG /* watchdog disabled */
-#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */
+#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */
/*
* Miscellaneous configurable options
@@ -101,89 +101,89 @@
#undef CFG_HUSH_PARSER /* use "hush" command parser */
#ifdef CFG_HUSH_PARSER
-#define CFG_PROMPT_HUSH_PS2 "> "
+#define CFG_PROMPT_HUSH_PS2 "> "
#endif
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
#endif
#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
#define CFG_MAXARGS 16 /* max number of command args */
#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_DEVICE_NULLDEV 1 /* include nulldev device */
+#define CFG_DEVICE_NULLDEV 1 /* include nulldev device */
-#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
+#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-#undef CFG_EXT_SERIAL_CLOCK /* no external serial clock used */
-#define CFG_IGNORE_405_UART_ERRATA_59 /* ignore ppc405gp errata #59 */
-#define CFG_BASE_BAUD 691200
+#undef CFG_EXT_SERIAL_CLOCK /* no external serial clock used */
+#define CFG_IGNORE_405_UART_ERRATA_59 /* ignore ppc405gp errata #59 */
+#define CFG_BASE_BAUD 691200
/* The following table includes the supported baudrates */
-#define CFG_BAUDRATE_TABLE \
+#define CFG_BAUDRATE_TABLE \
{ 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \
57600, 115200, 230400, 460800, 921600 }
#define CFG_LOAD_ADDR 0x100000 /* default load address */
#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
+#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
-#define CFG_RX_ETH_BUFFER 16 /* use 16 rx buffer on 405 emac */
+#define CFG_RX_ETH_BUFFER 16 /* use 16 rx buffer on 405 emac */
/*-----------------------------------------------------------------------
* PCI stuff
*-----------------------------------------------------------------------
*/
-#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */
-#define PCI_HOST_FORCE 1 /* configure as pci host */
-#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
+#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */
+#define PCI_HOST_FORCE 1 /* configure as pci host */
+#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
-#define CONFIG_PCI /* include pci support */
-#define CONFIG_PCI_HOST PCI_HOST_AUTO /* select pci host function */
-#define CONFIG_PCI_PNP /* do pci plug-and-play */
- /* resource configuration */
+#define CONFIG_PCI /* include pci support */
+#define CONFIG_PCI_HOST PCI_HOST_AUTO /* select pci host function */
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
+ /* resource configuration */
-#define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */
+#define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */
-#define CONFIG_PCI_BOOTDELAY 0 /* enable pci bootdelay variable*/
+#define CONFIG_PCI_BOOTDELAY 0 /* enable pci bootdelay variable*/
-#define CFG_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */
-#define CFG_PCI_SUBSYS_DEVICEID 0x0405 /* PCI Device ID: CPCI-405 */
-#define CFG_PCI_SUBSYS_DEVICEID2 0x0406 /* PCI Device ID: CPCI-405-A */
-#define CFG_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/
-#define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */
-#define CFG_PCI_PTM1MS 0xfc000001 /* 64MB, enable hard-wired to 1 */
-#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
-#define CFG_PCI_PTM2LA 0xffc00000 /* point to flash */
-#define CFG_PCI_PTM2MS 0xffc00001 /* 4MB, enable */
-#define CFG_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */
+#define CFG_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */
+#define CFG_PCI_SUBSYS_DEVICEID 0x0405 /* PCI Device ID: CPCI-405 */
+#define CFG_PCI_SUBSYS_DEVICEID2 0x0406 /* PCI Device ID: CPCI-405-A */
+#define CFG_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/
+#define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */
+#define CFG_PCI_PTM1MS 0xfc000001 /* 64MB, enable hard-wired to 1 */
+#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
+#define CFG_PCI_PTM2LA 0xffc00000 /* point to flash */
+#define CFG_PCI_PTM2MS 0xffc00001 /* 4MB, enable */
+#define CFG_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */
/*-----------------------------------------------------------------------
* IDE/ATA stuff
*-----------------------------------------------------------------------
*/
-#undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */
-#undef CONFIG_IDE_LED /* no led for ide supported */
+#undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */
+#undef CONFIG_IDE_LED /* no led for ide supported */
#define CONFIG_IDE_RESET 1 /* reset for ide supported */
-#define CFG_IDE_MAXBUS 1 /* max. 1 IDE busses */
-#define CFG_IDE_MAXDEVICE (CFG_IDE_MAXBUS*1) /* max. 1 drives per IDE bus */
+#define CFG_IDE_MAXBUS 1 /* max. 1 IDE busses */
+#define CFG_IDE_MAXDEVICE (CFG_IDE_MAXBUS*1) /* max. 1 drives per IDE bus */
-#define CFG_ATA_BASE_ADDR 0xF0100000
-#define CFG_ATA_IDE0_OFFSET 0x0000
+#define CFG_ATA_BASE_ADDR 0xF0100000
+#define CFG_ATA_IDE0_OFFSET 0x0000
#define CFG_ATA_DATA_OFFSET 0x0000 /* Offset for data I/O */
-#define CFG_ATA_REG_OFFSET 0x0000 /* Offset for normal register accesses */
+#define CFG_ATA_REG_OFFSET 0x0000 /* Offset for normal register accesses */
#define CFG_ATA_ALT_OFFSET 0x0000 /* Offset for alternate registers */
/*-----------------------------------------------------------------------
@@ -212,21 +212,21 @@
#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
-#define CFG_FLASH_WORD_SIZE unsigned short /* flash word size (width) */
-#define CFG_FLASH_ADDR0 0x5555 /* 1st address for flash config cycles */
-#define CFG_FLASH_ADDR1 0x2AAA /* 2nd address for flash config cycles */
+#define CFG_FLASH_WORD_SIZE unsigned short /* flash word size (width) */
+#define CFG_FLASH_ADDR0 0x5555 /* 1st address for flash config cycles */
+#define CFG_FLASH_ADDR1 0x2AAA /* 2nd address for flash config cycles */
/*
* The following defines are added for buggy IOP480 byte interface.
* All other boards should use the standard values (CPCI405 etc.)
*/
-#define CFG_FLASH_READ0 0x0000 /* 0 is standard */
-#define CFG_FLASH_READ1 0x0001 /* 1 is standard */
-#define CFG_FLASH_READ2 0x0002 /* 2 is standard */
+#define CFG_FLASH_READ0 0x0000 /* 0 is standard */
+#define CFG_FLASH_READ1 0x0001 /* 1 is standard */
+#define CFG_FLASH_READ2 0x0002 /* 2 is standard */
-#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
+#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
-#define CFG_JFFS2_FIRST_BANK 0 /* use for JFFS2 */
-#define CFG_JFFS2_NUM_BANKS 1 /* ! second bank contains U-Boot */
+#define CFG_JFFS2_FIRST_BANK 0 /* use for JFFS2 */
+#define CFG_JFFS2_NUM_BANKS 1 /* ! second bank contains U-Boot */
/*-----------------------------------------------------------------------
* I2C EEPROM (CAT24WC32) for environment
@@ -236,20 +236,20 @@
#define CFG_I2C_SLAVE 0x7F
#define CFG_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC32 */
-#define CFG_I2C_EEPROM_ADDR_LEN 2 /* Bytes of address */
-/* mask of address bits that overflow into the "EEPROM chip address" */
+#define CFG_I2C_EEPROM_ADDR_LEN 2 /* Bytes of address */
+/* mask of address bits that overflow into the "EEPROM chip address" */
#define CFG_I2C_EEPROM_ADDR_OVERFLOW 0x01
#define CFG_EEPROM_PAGE_WRITE_BITS 5 /* The Catalyst CAT24WC32 has */
/* 32 byte page write mode using*/
- /* last 5 bits of the address */
+ /* last 5 bits of the address */
#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
#define CFG_EEPROM_PAGE_WRITE_ENABLE
/* Use EEPROM for environment variables */
-#define CFG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
-#define CFG_ENV_OFFSET 0x000 /* environment starts at the beginning of the EEPROM */
-#define CFG_ENV_SIZE 0x800 /* 2048 bytes may be used for env vars*/
+#define CFG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
+#define CFG_ENV_OFFSET 0x000 /* environment starts at the beginning of the EEPROM */
+#define CFG_ENV_SIZE 0x800 /* 2048 bytes may be used for env vars*/
/* total size of a CAT24WC32 is 4096 bytes */
#define CFG_NVRAM_BASE_ADDR 0xf0200000 /* NVRAM base address */
@@ -259,8 +259,8 @@
/*-----------------------------------------------------------------------
* Cache Configuration
*/
-#define CFG_DCACHE_SIZE 16384 /* For IBM 405 CPUs, older 405 ppc's */
- /* have only 8kB, 16kB is save here */
+#define CFG_DCACHE_SIZE 16384 /* For IBM 405 CPUs, older 405 ppc's */
+ /* have only 8kB, 16kB is save here */
#define CFG_CACHELINE_SIZE 32 /* ... */
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
@@ -279,89 +279,89 @@
* External Bus Controller (EBC) Setup
*/
-/* Memory Bank 0 (Flash Bank 0) initialization */
-#define CFG_EBC_PB0AP 0x92015480
-#define CFG_EBC_PB0CR 0xFFC5A000 /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
+/* Memory Bank 0 (Flash Bank 0) initialization */
+#define CFG_EBC_PB0AP 0x92015480
+#define CFG_EBC_PB0CR 0xFFC5A000 /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
-/* Memory Bank 1 (Flash Bank 1) initialization */
-#define CFG_EBC_PB1AP 0x92015480
-#define CFG_EBC_PB1CR 0xFF85A000 /* BAS=0xFF8,BS=4MB,BU=R/W,BW=16bit */
+/* Memory Bank 1 (Flash Bank 1) initialization */
+#define CFG_EBC_PB1AP 0x92015480
+#define CFG_EBC_PB1CR 0xFF85A000 /* BAS=0xFF8,BS=4MB,BU=R/W,BW=16bit */
-/* Memory Bank 2 (CAN0, 1) initialization */
-#define CFG_EBC_PB2AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
-#define CFG_EBC_PB2CR 0xF0018000 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */
-#define CFG_LED_ADDR 0xF0000380
+/* Memory Bank 2 (CAN0, 1) initialization */
+#define CFG_EBC_PB2AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
+#define CFG_EBC_PB2CR 0xF0018000 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */
+#define CFG_LED_ADDR 0xF0000380
-/* Memory Bank 3 (CompactFlash IDE) initialization */
-#define CFG_EBC_PB3AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
-#define CFG_EBC_PB3CR 0xF011A000 /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */
+/* Memory Bank 3 (CompactFlash IDE) initialization */
+#define CFG_EBC_PB3AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
+#define CFG_EBC_PB3CR 0xF011A000 /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */
-/* Memory Bank 4 (NVRAM/RTC) initialization */
-/*#define CFG_EBC_PB4AP 0x01805280 / * TWT=3,WBN=1,WBF=1,TH=1,SOR=1 */
-#define CFG_EBC_PB4AP 0x01805680 /* TWT=3,WBN=1,WBF=1,TH=3,SOR=1 */
-#define CFG_EBC_PB4CR 0xF0218000 /* BAS=0xF02,BS=1MB,BU=R/W,BW=8bit */
+/* Memory Bank 4 (NVRAM/RTC) initialization */
+/*#define CFG_EBC_PB4AP 0x01805280 / * TWT=3,WBN=1,WBF=1,TH=1,SOR=1 */
+#define CFG_EBC_PB4AP 0x01805680 /* TWT=3,WBN=1,WBF=1,TH=3,SOR=1 */
+#define CFG_EBC_PB4CR 0xF0218000 /* BAS=0xF02,BS=1MB,BU=R/W,BW=8bit */
-/* Memory Bank 5 (optional Quart) initialization */
-#define CFG_EBC_PB5AP 0x04005B80 /* TWT=8,WBN=1,WBF=1,TH=5,RE=1,SOR=1*/
-#define CFG_EBC_PB5CR 0xF0318000 /* BAS=0xF03,BS=1MB,BU=R/W,BW=8bit */
+/* Memory Bank 5 (optional Quart) initialization */
+#define CFG_EBC_PB5AP 0x04005B80 /* TWT=8,WBN=1,WBF=1,TH=5,RE=1,SOR=1*/
+#define CFG_EBC_PB5CR 0xF0318000 /* BAS=0xF03,BS=1MB,BU=R/W,BW=8bit */
-/* Memory Bank 6 (FPGA internal) initialization */
-#define CFG_EBC_PB6AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
-#define CFG_EBC_PB6CR 0xF041A000 /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */
-#define CFG_FPGA_BASE_ADDR 0xF0400000
+/* Memory Bank 6 (FPGA internal) initialization */
+#define CFG_EBC_PB6AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
+#define CFG_EBC_PB6CR 0xF041A000 /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */
+#define CFG_FPGA_BASE_ADDR 0xF0400000
/*-----------------------------------------------------------------------
* FPGA stuff
*/
/* FPGA internal regs */
-#define CFG_FPGA_MODE 0x00
-#define CFG_FPGA_STATUS 0x02
-#define CFG_FPGA_TS 0x04
-#define CFG_FPGA_TS_LOW 0x06
-#define CFG_FPGA_TS_CAP0 0x10
-#define CFG_FPGA_TS_CAP0_LOW 0x12
-#define CFG_FPGA_TS_CAP1 0x14
-#define CFG_FPGA_TS_CAP1_LOW 0x16
-#define CFG_FPGA_TS_CAP2 0x18
-#define CFG_FPGA_TS_CAP2_LOW 0x1a
-#define CFG_FPGA_TS_CAP3 0x1c
-#define CFG_FPGA_TS_CAP3_LOW 0x1e
+#define CFG_FPGA_MODE 0x00
+#define CFG_FPGA_STATUS 0x02
+#define CFG_FPGA_TS 0x04
+#define CFG_FPGA_TS_LOW 0x06
+#define CFG_FPGA_TS_CAP0 0x10
+#define CFG_FPGA_TS_CAP0_LOW 0x12
+#define CFG_FPGA_TS_CAP1 0x14
+#define CFG_FPGA_TS_CAP1_LOW 0x16
+#define CFG_FPGA_TS_CAP2 0x18
+#define CFG_FPGA_TS_CAP2_LOW 0x1a
+#define CFG_FPGA_TS_CAP3 0x1c
+#define CFG_FPGA_TS_CAP3_LOW 0x1e
/* FPGA Mode Reg */
-#define CFG_FPGA_MODE_CF_RESET 0x0001
+#define CFG_FPGA_MODE_CF_RESET 0x0001
#define CFG_FPGA_MODE_DUART_RESET 0x0002
#define CFG_FPGA_MODE_ENABLE_OUTPUT 0x0004 /* only set on CPCI-405 Ver 3 */
#define CFG_FPGA_MODE_TS_IRQ_ENABLE 0x0100
#define CFG_FPGA_MODE_TS_IRQ_CLEAR 0x1000
-#define CFG_FPGA_MODE_TS_CLEAR 0x2000
+#define CFG_FPGA_MODE_TS_CLEAR 0x2000
/* FPGA Status Reg */
-#define CFG_FPGA_STATUS_DIP0 0x0001
-#define CFG_FPGA_STATUS_DIP1 0x0002
-#define CFG_FPGA_STATUS_DIP2 0x0004
-#define CFG_FPGA_STATUS_FLASH 0x0008
-#define CFG_FPGA_STATUS_TS_IRQ 0x1000
+#define CFG_FPGA_STATUS_DIP0 0x0001
+#define CFG_FPGA_STATUS_DIP1 0x0002
+#define CFG_FPGA_STATUS_DIP2 0x0004
+#define CFG_FPGA_STATUS_FLASH 0x0008
+#define CFG_FPGA_STATUS_TS_IRQ 0x1000
-#define CFG_FPGA_SPARTAN2 1 /* using Xilinx Spartan 2 now */
-#define CFG_FPGA_MAX_SIZE 128*1024 /* 128kByte is enough for XC2S30 */
+#define CFG_FPGA_SPARTAN2 1 /* using Xilinx Spartan 2 now */
+#define CFG_FPGA_MAX_SIZE 128*1024 /* 128kByte is enough for XC2S30 */
/* FPGA program pin configuration */
-#define CFG_FPGA_PRG 0x04000000 /* FPGA program pin (ppc output) */
-#define CFG_FPGA_CLK 0x02000000 /* FPGA clk pin (ppc output) */
-#define CFG_FPGA_DATA 0x01000000 /* FPGA data pin (ppc output) */
-#define CFG_FPGA_INIT 0x00010000 /* FPGA init pin (ppc input) */
-#define CFG_FPGA_DONE 0x00008000 /* FPGA done pin (ppc input) */
+#define CFG_FPGA_PRG 0x04000000 /* FPGA program pin (ppc output) */
+#define CFG_FPGA_CLK 0x02000000 /* FPGA clk pin (ppc output) */
+#define CFG_FPGA_DATA 0x01000000 /* FPGA data pin (ppc output) */
+#define CFG_FPGA_INIT 0x00010000 /* FPGA init pin (ppc input) */
+#define CFG_FPGA_DONE 0x00008000 /* FPGA done pin (ppc input) */
/*-----------------------------------------------------------------------
* Definitions for initial stack pointer and data area (in data cache)
*/
-#define CFG_INIT_DCACHE_CS 7 /* use cs # 7 for data cache memory */
+#define CFG_INIT_DCACHE_CS 7 /* use cs # 7 for data cache memory */
-#define CFG_INIT_RAM_ADDR 0x40000000 /* use data cache */
-#define CFG_INIT_RAM_END 0x2000 /* End of used area in RAM */
+#define CFG_INIT_RAM_ADDR 0x40000000 /* use data cache */
+#define CFG_INIT_RAM_END 0x2000 /* End of used area in RAM */
#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
/*
diff --git a/include/configs/CPCI440.h b/include/configs/CPCI440.h
index 55bb1ec..3e0cee4 100644
--- a/include/configs/CPCI440.h
+++ b/include/configs/CPCI440.h
@@ -33,7 +33,7 @@
*----------------------------------------------------------------------*/
#define CONFIG_EBONY 1 /* Board is ebony */
#define CONFIG_4xx 1 /* ... PPC4xx family */
-#define CONFIG_BOARD_PRE_INIT 1 /* Call board_pre_init */
+#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
#undef CFG_DRAM_TEST /* Disable-takes long time! */
#define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */
diff --git a/include/configs/CPCIISER4.h b/include/configs/CPCIISER4.h
index bcda699..1aff9e4 100644
--- a/include/configs/CPCIISER4.h
+++ b/include/configs/CPCIISER4.h
@@ -34,12 +34,12 @@
*/
#define CONFIG_405GP 1 /* This is a PPC405 CPU */
-#define CONFIG_4xx 1 /* ...member of PPC4xx family */
+#define CONFIG_4xx 1 /* ...member of PPC4xx family */
#define CONFIG_CPCIISER4 1 /* ...on a CPCIISER4 board */
-#define CONFIG_BOARD_PRE_INIT 1 /* call board_pre_init() */
+#define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */
-#define CONFIG_SYS_CLK_FREQ 25000000 /* external frequency to pll */
+#define CONFIG_SYS_CLK_FREQ 25000000 /* external frequency to pll */
#define CONFIG_BAUDRATE 9600
#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */
@@ -51,21 +51,21 @@
#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
#define CONFIG_MII 1 /* MII PHY management */
-#define CONFIG_PHY_ADDR 0 /* PHY address */
+#define CONFIG_PHY_ADDR 0 /* PHY address */
#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \
CFG_CMD_PCI | \
CFG_CMD_IRQ | \
CFG_CMD_MII | \
CFG_CMD_ELF | \
- CFG_CMD_EEPROM )
+ CFG_CMD_EEPROM )
/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
#include <cmd_confdefs.h>
#undef CONFIG_WATCHDOG /* watchdog disabled */
-#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */
+#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */
/*
* Miscellaneous configurable options
@@ -73,30 +73,30 @@
#define CFG_LONGHELP /* undef to save memory */
#define CFG_PROMPT "=> " /* Monitor Command Prompt */
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
#endif
#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
#define CFG_MAXARGS 16 /* max number of command args */
#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
+#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-#define CFG_EXT_SERIAL_CLOCK 1843200 /* use external serial clock */
+#define CFG_EXT_SERIAL_CLOCK 1843200 /* use external serial clock */
/* The following table includes the supported baudrates */
-#define CFG_BAUDRATE_TABLE \
+#define CFG_BAUDRATE_TABLE \
{ 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \
57600, 115200, 230400, 460800, 921600 }
#define CFG_LOAD_ADDR 0x100000 /* default load address */
#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
@@ -104,23 +104,23 @@
* PCI stuff
*-----------------------------------------------------------------------
*/
-#define PCI_HOST_ADAPTER 0 /* configure ar pci adapter */
-#define PCI_HOST_FORCE 1 /* configure as pci host */
-#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
+#define PCI_HOST_ADAPTER 0 /* configure ar pci adapter */
+#define PCI_HOST_FORCE 1 /* configure as pci host */
+#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
-#define CONFIG_PCI /* include pci support */
-#define CONFIG_PCI_HOST PCI_HOST_AUTO /* select pci host function */
-#define CONFIG_PCI_PNP /* do pci plug-and-play */
- /* resource configuration */
+#define CONFIG_PCI /* include pci support */
+#define CONFIG_PCI_HOST PCI_HOST_AUTO /* select pci host function */
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
+ /* resource configuration */
-#define CFG_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */
-#define CFG_PCI_SUBSYS_DEVICEID 0x0404 /* PCI Device ID: CPCI-ISER4 */
-#define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */
-#define CFG_PCI_PTM1MS 0xff000001 /* 16MB, enable hard-wired to 1 */
-#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
-#define CFG_PCI_PTM2LA 0xffe00000 /* point to flash */
-#define CFG_PCI_PTM2MS 0xffe00001 /* 2MB, enable */
-#define CFG_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */
+#define CFG_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */
+#define CFG_PCI_SUBSYS_DEVICEID 0x0404 /* PCI Device ID: CPCI-ISER4 */
+#define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */
+#define CFG_PCI_PTM1MS 0xff000001 /* 16MB, enable hard-wired to 1 */
+#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
+#define CFG_PCI_PTM2LA 0xffe00000 /* point to flash */
+#define CFG_PCI_PTM2MS 0xffe00001 /* 2MB, enable */
+#define CFG_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */
/*-----------------------------------------------------------------------
* Start addresses for the final memory configuration
@@ -148,18 +148,18 @@
#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
-#define CFG_FLASH_WORD_SIZE unsigned short /* flash word size (width) */
-#define CFG_FLASH_ADDR0 0x5555 /* 1st address for flash config cycles */
-#define CFG_FLASH_ADDR1 0x2AAA /* 2nd address for flash config cycles */
+#define CFG_FLASH_WORD_SIZE unsigned short /* flash word size (width) */
+#define CFG_FLASH_ADDR0 0x5555 /* 1st address for flash config cycles */
+#define CFG_FLASH_ADDR1 0x2AAA /* 2nd address for flash config cycles */
/*
* The following defines are added for buggy IOP480 byte interface.
* All other boards should use the standard values (CPCI405 etc.)
*/
-#define CFG_FLASH_READ0 0x0000 /* 0 is standard */
-#define CFG_FLASH_READ1 0x0001 /* 1 is standard */
-#define CFG_FLASH_READ2 0x0002 /* 2 is standard */
+#define CFG_FLASH_READ0 0x0000 /* 0 is standard */
+#define CFG_FLASH_READ1 0x0001 /* 1 is standard */
+#define CFG_FLASH_READ2 0x0002 /* 2 is standard */
-#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
+#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
/*-----------------------------------------------------------------------
* I2C EEPROM (CAT24WC08) for environment
@@ -169,18 +169,18 @@
#define CFG_I2C_SLAVE 0x7F
#define CFG_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC08 */
-#define CFG_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
-/* mask of address bits that overflow into the "EEPROM chip address" */
+#define CFG_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
+/* mask of address bits that overflow into the "EEPROM chip address" */
#define CFG_I2C_EEPROM_ADDR_OVERFLOW 0x07
#define CFG_EEPROM_PAGE_WRITE_BITS 4 /* The Catalyst CAT24WC08 has */
/* 16 byte page write mode using*/
- /* last 4 bits of the address */
+ /* last 4 bits of the address */
#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
#define CFG_EEPROM_PAGE_WRITE_ENABLE
-#define CFG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
-#define CFG_ENV_OFFSET 0x000 /* environment starts at the beginning of the EEPROM */
-#define CFG_ENV_SIZE 0x300 /* 768 bytes may be used for env vars */
+#define CFG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
+#define CFG_ENV_OFFSET 0x000 /* environment starts at the beginning of the EEPROM */
+#define CFG_ENV_SIZE 0x300 /* 768 bytes may be used for env vars */
/* total size of a CAT24WC08 is 1024 bytes */
/*-----------------------------------------------------------------------
@@ -205,31 +205,31 @@
* External Bus Controller (EBC) Setup
*/
-/* Memory Bank 0 (Flash Bank 0) initialization */
-#define CFG_EBC_PB0AP 0x92015480
-#define CFG_EBC_PB0CR 0xFFC5A000 /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
+/* Memory Bank 0 (Flash Bank 0) initialization */
+#define CFG_EBC_PB0AP 0x92015480
+#define CFG_EBC_PB0CR 0xFFC5A000 /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
-/* Memory Bank 1 (Uart 8bit) initialization */
-#define CFG_EBC_PB1AP 0x01000480 /* TWT=2,TH=2,no Ready,BEM=0,SOR=1 */
-#define CFG_EBC_PB1CR 0xF0018000 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */
+/* Memory Bank 1 (Uart 8bit) initialization */
+#define CFG_EBC_PB1AP 0x01000480 /* TWT=2,TH=2,no Ready,BEM=0,SOR=1 */
+#define CFG_EBC_PB1CR 0xF0018000 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */
-/* Memory Bank 2 (Uart 32bit) initialization */
-#define CFG_EBC_PB2AP 0x000004c0 /* no Ready, BEM=1 */
-#define CFG_EBC_PB2CR 0xF011C000 /* BAS=0xF01,BS=1MB,BU=R/W,BW=32bit */
+/* Memory Bank 2 (Uart 32bit) initialization */
+#define CFG_EBC_PB2AP 0x000004c0 /* no Ready, BEM=1 */
+#define CFG_EBC_PB2CR 0xF011C000 /* BAS=0xF01,BS=1MB,BU=R/W,BW=32bit */
-/* Memory Bank 3 (FPGA Reset) initialization */
-#define CFG_EBC_PB3AP 0x010004C0 /* no Ready, BEM=1 */
-#define CFG_EBC_PB3CR 0xF021A000 /* BAS=0xF02,BS=1MB,BU=R/W,BW=16bit */
+/* Memory Bank 3 (FPGA Reset) initialization */
+#define CFG_EBC_PB3AP 0x010004C0 /* no Ready, BEM=1 */
+#define CFG_EBC_PB3CR 0xF021A000 /* BAS=0xF02,BS=1MB,BU=R/W,BW=16bit */
/*-----------------------------------------------------------------------
* Definitions for initial stack pointer and data area (in DPRAM)
*/
-#define CFG_INIT_DCACHE_CS 7 /* use cs # 7 for data cache memory */
-#define CFG_INIT_RAM_ADDR 0x40000000 /* use data cache */
-#define CFG_INIT_RAM_END 0x2000 /* End of used area in RAM */
+#define CFG_INIT_DCACHE_CS 7 /* use cs # 7 for data cache memory */
+#define CFG_INIT_RAM_ADDR 0x40000000 /* use data cache */
+#define CFG_INIT_RAM_END 0x2000 /* End of used area in RAM */
#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
/*
* Internal Definitions
diff --git a/include/configs/CRAYL1.h b/include/configs/CRAYL1.h
index fd85944..63d7a92 100644
--- a/include/configs/CRAYL1.h
+++ b/include/configs/CRAYL1.h
@@ -1,5 +1,5 @@
/*
- * (C) Copyright 2000, 2001
+ * (C) Copyright 2000-2004
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
* David Updegraff, Cray, Inc. dave@cray.com: our 405 is walnut-lite..
*
@@ -41,7 +41,7 @@
#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_PHY_ADDR 1 /* PHY address; handling of ENET */
-#define CONFIG_BOARD_PRE_INIT 1 /* early setup for 405gp */
+#define CONFIG_BOARD_EARLY_INIT_F 1 /* early setup for 405gp */
#define CONFIG_MISC_INIT_R 1 /* so that a misc_init_r() is called */
/* set PRAM to keep U-Boot out, mem= to keep linux out, and initrd_hi to
diff --git a/include/configs/DASA_SIM.h b/include/configs/DASA_SIM.h
index 30e978c..5ff9b9e 100644
--- a/include/configs/DASA_SIM.h
+++ b/include/configs/DASA_SIM.h
@@ -12,7 +12,7 @@
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
@@ -34,20 +34,20 @@
*/
#define CONFIG_IOP480 1 /* This is a IOP480 CPU */
-#define CONFIG_DASA_SIM 1 /* ...on a DASA_SIM board */
+#define CONFIG_DASA_SIM 1 /* ...on a DASA_SIM board */
-#define CONFIG_BOARD_PRE_INIT 1 /* call board_pre_init() */
+#define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */
-#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */
+#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */
-#define CONFIG_CPUCLOCK 66
-#define CONFIG_BUSCLOCK (CONFIG_CPUCLOCK)
+#define CONFIG_CPUCLOCK 66
+#define CONFIG_BUSCLOCK (CONFIG_CPUCLOCK)
-#define CONFIG_BAUDRATE 9600
+#define CONFIG_BAUDRATE 9600
#define CONFIG_BOOTDELAY 3 /* autoboot after 5 seconds */
#define CONFIG_BOOTCOMMAND "bootm ffe00000" /* autoboot command */
-#undef CONFIG_BOOTARGS
+#undef CONFIG_BOOTARGS
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
@@ -63,16 +63,16 @@
CFG_CMD_IRQ | \
CFG_CMD_BSP | \
CFG_CMD_ASKENV | \
- CFG_CMD_ELF )
+ CFG_CMD_ELF )
#else
#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \
- CFG_CMD_BSP )
+ CFG_CMD_BSP )
#endif
#if 0 /* Does not appear to be used?! If it is used, needs to be fixed */
#define CONFIG_SOFT_I2C /* Software I2C support enabled */
#endif
-#define CFG_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
+#define CFG_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
#include <cmd_confdefs.h>
@@ -83,33 +83,33 @@
#define CFG_LONGHELP /* undef to save memory */
#define CFG_PROMPT "=> " /* Monitor Command Prompt */
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
#endif
#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
#define CFG_MAXARGS 16 /* max number of command args */
#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
+#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
/* The following table includes the supported baudrates */
-#define CFG_BAUDRATE_TABLE \
+#define CFG_BAUDRATE_TABLE \
{ 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200 }
-#define CFG_LOAD_ADDR 0x100000 /* default load address */
+#define CFG_LOAD_ADDR 0x100000 /* default load address */
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
/*-----------------------------------------------------------------------
* Definitions for initial stack pointer and data area (in DPRAM)
*/
-#define CFG_INIT_RAM_ADDR 0x00df0000 /* inside of SDRAM */
+#define CFG_INIT_RAM_ADDR 0x00df0000 /* inside of SDRAM */
#define CFG_INIT_RAM_END 0x0f00 /* End of used area in RAM */
#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
@@ -131,37 +131,37 @@
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
/*-----------------------------------------------------------------------
* FLASH organization
*/
#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#define CFG_MAX_FLASH_SECT 256 /* max number of sectors on one chip */
+#define CFG_MAX_FLASH_SECT 256 /* max number of sectors on one chip */
#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
-#define CFG_FLASH_WORD_SIZE unsigned char /* flash word size (width) */
-#define CFG_FLASH_ADDR0 0x0AA9 /* 1st address for flash config cycles */
-#define CFG_FLASH_ADDR1 0x0556 /* 2nd address for flash config cycles */
+#define CFG_FLASH_WORD_SIZE unsigned char /* flash word size (width) */
+#define CFG_FLASH_ADDR0 0x0AA9 /* 1st address for flash config cycles */
+#define CFG_FLASH_ADDR1 0x0556 /* 2nd address for flash config cycles */
/*
* The following defines are added for buggy IOP480 byte interface.
* All other boards should use the standard values (CPCI405 etc.)
*/
-#define CFG_FLASH_READ0 0x0002 /* 0 is standard */
-#define CFG_FLASH_READ1 0x0000 /* 1 is standard */
-#define CFG_FLASH_READ2 0x0004 /* 2 is standard */
+#define CFG_FLASH_READ0 0x0002 /* 0 is standard */
+#define CFG_FLASH_READ1 0x0000 /* 1 is standard */
+#define CFG_FLASH_READ2 0x0004 /* 2 is standard */
-#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
+#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
-#define CFG_ENV_IS_IN_FLASH 1
-#define CFG_ENV_OFFSET 0x00010000 /* Offset of Environment Sector */
+#define CFG_ENV_IS_IN_FLASH 1
+#define CFG_ENV_OFFSET 0x00010000 /* Offset of Environment Sector */
#define CFG_ENV_SIZE 0x1000 /* Total Size of Environment Sector */
#if 0
#define CFG_ENV_SECT_SIZE 0x8000 /* see README - env sector total size */
#else
-#define CFG_ENV_SECT_SIZE 0x10000 /* see README - env sector total size */
+#define CFG_ENV_SECT_SIZE 0x10000 /* see README - env sector total size */
#endif
/*-----------------------------------------------------------------------
@@ -170,12 +170,12 @@
#define CONFIG_PCI /* include pci support */
#undef CONFIG_PCI_PNP
-#define CONFIG_NET_MULTI /* Multi ethernet cards support */
+#define CONFIG_NET_MULTI /* Multi ethernet cards support */
#define CONFIG_TULIP
-#define CFG_ETH_DEV_FN 0x0000
-#define CFG_ETH_IOBASE 0x0fff0000
+#define CFG_ETH_DEV_FN 0x0000
+#define CFG_ETH_IOBASE 0x0fff0000
#define CFG_PCI9054_DEV_FN 0x0800
#define CFG_PCI9054_IOBASE 0x0eff0000
diff --git a/include/configs/DB64360.h b/include/configs/DB64360.h
index 25614b0..e318b27 100644
--- a/include/configs/DB64360.h
+++ b/include/configs/DB64360.h
@@ -131,7 +131,7 @@
/* which initialization functions to call for this board */
#define CONFIG_MISC_INIT_R /* initialize the icache L1 */
-#define CONFIG_BOARD_PRE_INIT
+#define CONFIG_BOARD_EARLY_INIT_F
#define CFG_BOARD_NAME "DB64360"
#define CONFIG_IDENT_STRING "Marvell DB64360 (1.1)"
diff --git a/include/configs/DB64460.h b/include/configs/DB64460.h
index acf2bec..e58b63a 100644
--- a/include/configs/DB64460.h
+++ b/include/configs/DB64460.h
@@ -68,7 +68,7 @@
/* which initialization functions to call for this board */
#define CONFIG_MISC_INIT_R /* initialize the icache L1 */
-#define CONFIG_BOARD_PRE_INIT
+#define CONFIG_BOARD_EARLY_INIT_F
#define CFG_BOARD_NAME "DB64460"
#define CONFIG_IDENT_STRING "Marvell DB64460 (1.0)"
diff --git a/include/configs/DK1C20.h b/include/configs/DK1C20.h
index 0d8e463..92c8e51 100644
--- a/include/configs/DK1C20.h
+++ b/include/configs/DK1C20.h
@@ -295,7 +295,7 @@
#define CONFIG_SYS_CLK_FREQ CFG_NIOS_CPU_CLK/* 50 MHz core clock */
#define CFG_HZ 1000 /* 1 msec time tick */
#undef CFG_CLKS_IN_HZ
-#define CONFIG_BOARD_PRE_INIT 1 /* enable early board-spec. init*/
+#define CONFIG_BOARD_EARLY_INIT_F 1 /* enable early board-spec. init*/
/*------------------------------------------------------------------------
* BASE ADDRESSES / SIZE (Flash, SRAM, SDRAM)
diff --git a/include/configs/DK1S10.h b/include/configs/DK1S10.h
index c54ac58..bd7ded5 100644
--- a/include/configs/DK1S10.h
+++ b/include/configs/DK1S10.h
@@ -294,7 +294,7 @@
#define CONFIG_SYS_CLK_FREQ CFG_NIOS_CPU_CLK/* 50 MHz core clock */
#define CFG_HZ 1000 /* 1 msec time tick */
#undef CFG_CLKS_IN_HZ
-#define CONFIG_BOARD_PRE_INIT 1 /* enable early board-spec. init*/
+#define CONFIG_BOARD_EARLY_INIT_F 1 /* enable early board-spec. init*/
/*------------------------------------------------------------------------
* BASE ADDRESSES / SIZE (Flash, SRAM, SDRAM)
diff --git a/include/configs/DP405.h b/include/configs/DP405.h
index 03bd080..666a0d0 100644
--- a/include/configs/DP405.h
+++ b/include/configs/DP405.h
@@ -34,13 +34,13 @@
*/
#define CONFIG_405EP 1 /* This is a PPC405 CPU */
-#define CONFIG_4xx 1 /* ...member of PPC4xx family */
-#define CONFIG_DP405 1 /* ...on a DP405 board */
+#define CONFIG_4xx 1 /* ...member of PPC4xx family */
+#define CONFIG_DP405 1 /* ...on a DP405 board */
-#define CONFIG_BOARD_PRE_INIT 1 /* call board_pre_init() */
-#define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */
+#define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */
+#define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */
-#define CONFIG_SYS_CLK_FREQ 33333334 /* external frequency to pll */
+#define CONFIG_SYS_CLK_FREQ 33333334 /* external frequency to pll */
#define CONFIG_BAUDRATE 9600
#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */
@@ -60,7 +60,7 @@
#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
#define CONFIG_MII 1 /* MII PHY management */
-#define CONFIG_PHY_ADDR 0 /* PHY address */
+#define CONFIG_PHY_ADDR 0 /* PHY address */
#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \
CFG_CMD_BSP | \
@@ -69,17 +69,17 @@
CFG_CMD_ELF | \
CFG_CMD_DATE | \
CFG_CMD_I2C | \
- CFG_CMD_EEPROM )
+ CFG_CMD_EEPROM )
/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
#include <cmd_confdefs.h>
-#undef CONFIG_WATCHDOG /* watchdog disabled */
+#undef CONFIG_WATCHDOG /* watchdog disabled */
-#define CONFIG_RTC_MC146818 /* DS1685 is MC146818 compatible*/
-#define CFG_RTC_REG_BASE_ADDR 0xF0000500 /* RTC Base Address */
+#define CONFIG_RTC_MC146818 /* DS1685 is MC146818 compatible*/
+#define CFG_RTC_REG_BASE_ADDR 0xF0000500 /* RTC Base Address */
-#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */
+#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */
/*
* Miscellaneous configurable options
@@ -89,70 +89,70 @@
#undef CFG_HUSH_PARSER /* use "hush" command parser */
#ifdef CFG_HUSH_PARSER
-#define CFG_PROMPT_HUSH_PS2 "> "
+#define CFG_PROMPT_HUSH_PS2 "> "
#endif
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
#endif
#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
#define CFG_MAXARGS 16 /* max number of command args */
#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_DEVICE_NULLDEV 1 /* include nulldev device */
+#define CFG_DEVICE_NULLDEV 1 /* include nulldev device */
-#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
+#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-#undef CFG_EXT_SERIAL_CLOCK /* no external serial clock used */
-#define CFG_IGNORE_405_UART_ERRATA_59 /* ignore ppc405gp errata #59 */
-#define CFG_BASE_BAUD 691200
-#undef CONFIG_UART1_CONSOLE /* define for uart1 as console */
+#undef CFG_EXT_SERIAL_CLOCK /* no external serial clock used */
+#define CFG_IGNORE_405_UART_ERRATA_59 /* ignore ppc405gp errata #59 */
+#define CFG_BASE_BAUD 691200
+#undef CONFIG_UART1_CONSOLE /* define for uart1 as console */
/* The following table includes the supported baudrates */
-#define CFG_BAUDRATE_TABLE \
+#define CFG_BAUDRATE_TABLE \
{ 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \
57600, 115200, 230400, 460800, 921600 }
#define CFG_LOAD_ADDR 0x100000 /* default load address */
#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
+#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
-#define CFG_RX_ETH_BUFFER 16 /* use 16 rx buffer on 405 emac */
+#define CFG_RX_ETH_BUFFER 16 /* use 16 rx buffer on 405 emac */
/*-----------------------------------------------------------------------
* PCI stuff
*-----------------------------------------------------------------------
*/
-#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */
-#define PCI_HOST_FORCE 1 /* configure as pci host */
-#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
+#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */
+#define PCI_HOST_FORCE 1 /* configure as pci host */
+#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
-#define CONFIG_PCI /* include pci support */
-#define CONFIG_PCI_HOST PCI_HOST_HOST /* select pci host function */
-#undef CONFIG_PCI_PNP /* do pci plug-and-play */
- /* resource configuration */
+#define CONFIG_PCI /* include pci support */
+#define CONFIG_PCI_HOST PCI_HOST_HOST /* select pci host function */
+#undef CONFIG_PCI_PNP /* do pci plug-and-play */
+ /* resource configuration */
-#undef CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */
+#undef CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */
-#define CFG_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */
-#define CFG_PCI_SUBSYS_DEVICEID 0x0405 /* PCI Device ID: CPCI-405 */
-#define CFG_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/
-#define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */
-#define CFG_PCI_PTM1MS 0xfc000001 /* 64MB, enable hard-wired to 1 */
-#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
-#define CFG_PCI_PTM2LA 0xffc00000 /* point to flash */
-#define CFG_PCI_PTM2MS 0xffc00001 /* 4MB, enable */
-#define CFG_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */
+#define CFG_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */
+#define CFG_PCI_SUBSYS_DEVICEID 0x0405 /* PCI Device ID: CPCI-405 */
+#define CFG_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/
+#define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */
+#define CFG_PCI_PTM1MS 0xfc000001 /* 64MB, enable hard-wired to 1 */
+#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
+#define CFG_PCI_PTM2LA 0xffc00000 /* point to flash */
+#define CFG_PCI_PTM2MS 0xffc00001 /* 4MB, enable */
+#define CFG_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */
/*
* For booting Linux, the board info and command line data
@@ -171,22 +171,22 @@
#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
#define CFG_FLASH_WRITE_TOUT 1000 /* Timeout for Flash Write (in ms) */
-#define CFG_FLASH_WORD_SIZE unsigned short /* flash word size (width) */
-#define CFG_FLASH_ADDR0 0x5555 /* 1st address for flash config cycles */
-#define CFG_FLASH_ADDR1 0x2AAA /* 2nd address for flash config cycles */
+#define CFG_FLASH_WORD_SIZE unsigned short /* flash word size (width) */
+#define CFG_FLASH_ADDR0 0x5555 /* 1st address for flash config cycles */
+#define CFG_FLASH_ADDR1 0x2AAA /* 2nd address for flash config cycles */
/*
* The following defines are added for buggy IOP480 byte interface.
* All other boards should use the standard values (CPCI405 etc.)
*/
-#define CFG_FLASH_READ0 0x0000 /* 0 is standard */
-#define CFG_FLASH_READ1 0x0001 /* 1 is standard */
-#define CFG_FLASH_READ2 0x0002 /* 2 is standard */
+#define CFG_FLASH_READ0 0x0000 /* 0 is standard */
+#define CFG_FLASH_READ1 0x0001 /* 1 is standard */
+#define CFG_FLASH_READ2 0x0002 /* 2 is standard */
-#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
+#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
#if 0 /* test-only */
-#define CFG_JFFS2_FIRST_BANK 0 /* use for JFFS2 */
-#define CFG_JFFS2_NUM_BANKS 1 /* ! second bank contains U-Boot */
+#define CFG_JFFS2_FIRST_BANK 0 /* use for JFFS2 */
+#define CFG_JFFS2_NUM_BANKS 1 /* ! second bank contains U-Boot */
#endif
/*-----------------------------------------------------------------------
@@ -209,13 +209,13 @@
/*-----------------------------------------------------------------------
* Environment Variable setup
*/
-#define CFG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
-#define CFG_ENV_OFFSET 0x100 /* environment starts at the beginning of the EEPROM */
-#define CFG_ENV_SIZE 0x700 /* 2048 bytes may be used for env vars*/
+#define CFG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
+#define CFG_ENV_OFFSET 0x100 /* environment starts at the beginning of the EEPROM */
+#define CFG_ENV_SIZE 0x700 /* 2048 bytes may be used for env vars*/
/* total size of a CAT24WC16 is 2048 bytes */
#define CFG_NVRAM_BASE_ADDR 0xF0000500 /* NVRAM base address */
-#define CFG_NVRAM_SIZE 242 /* NVRAM size */
+#define CFG_NVRAM_SIZE 242 /* NVRAM size */
/*-----------------------------------------------------------------------
* I2C EEPROM (CAT24WC16) for environment
@@ -225,20 +225,20 @@
#define CFG_I2C_SLAVE 0x7F
#define CFG_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC08 */
-#define CFG_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
-/* mask of address bits that overflow into the "EEPROM chip address" */
+#define CFG_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
+/* mask of address bits that overflow into the "EEPROM chip address" */
#define CFG_I2C_EEPROM_ADDR_OVERFLOW 0x07
#define CFG_EEPROM_PAGE_WRITE_BITS 4 /* The Catalyst CAT24WC08 has */
/* 16 byte page write mode using*/
- /* last 4 bits of the address */
+ /* last 4 bits of the address */
#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
#define CFG_EEPROM_PAGE_WRITE_ENABLE
/*-----------------------------------------------------------------------
* Cache Configuration
*/
-#define CFG_DCACHE_SIZE 16384 /* For IBM 405 CPUs, older 405 ppc's */
- /* have only 8kB, 16kB is save here */
+#define CFG_DCACHE_SIZE 16384 /* For IBM 405 CPUs, older 405 ppc's */
+ /* have only 8kB, 16kB is save here */
#define CFG_CACHELINE_SIZE 32 /* ... */
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
@@ -248,41 +248,41 @@
* External Bus Controller (EBC) Setup
*/
-#define CAN_BA 0xF0000000 /* CAN Base Address */
-#define RTC_BA 0xF0000500 /* RTC Base Address */
+#define CAN_BA 0xF0000000 /* CAN Base Address */
+#define RTC_BA 0xF0000500 /* RTC Base Address */
-/* Memory Bank 0 (Flash Bank 0, NOR-FLASH) initialization */
-#define CFG_EBC_PB0AP 0x92015480
-#define CFG_EBC_PB0CR 0xFFC5A000 /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
+/* Memory Bank 0 (Flash Bank 0, NOR-FLASH) initialization */
+#define CFG_EBC_PB0AP 0x92015480
+#define CFG_EBC_PB0CR 0xFFC5A000 /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
#if 0 /* test-only */
-/* Memory Bank 1 (Flash Bank 1, NAND-FLASH) initialization */
-#define CFG_EBC_PB1AP 0x92015480
-#define CFG_EBC_PB1CR 0xF4018000 /* BAS=0xF40,BS=1MB,BU=R/W,BW=8bit */
+/* Memory Bank 1 (Flash Bank 1, NAND-FLASH) initialization */
+#define CFG_EBC_PB1AP 0x92015480
+#define CFG_EBC_PB1CR 0xF4018000 /* BAS=0xF40,BS=1MB,BU=R/W,BW=8bit */
#endif
-/* Memory Bank 2 (8 Bit Peripheral: CAN, UART, RTC) initialization */
-#define CFG_EBC_PB2AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
-#define CFG_EBC_PB2CR 0xF0018000 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */
+/* Memory Bank 2 (8 Bit Peripheral: CAN, UART, RTC) initialization */
+#define CFG_EBC_PB2AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
+#define CFG_EBC_PB2CR 0xF0018000 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */
/*-----------------------------------------------------------------------
* FPGA stuff
*/
-#define CFG_FPGA_XC95XL 1 /* using Xilinx XC95XL CPLD */
-#define CFG_FPGA_MAX_SIZE 32*1024 /* 32kByte is enough for CPLD */
+#define CFG_FPGA_XC95XL 1 /* using Xilinx XC95XL CPLD */
+#define CFG_FPGA_MAX_SIZE 32*1024 /* 32kByte is enough for CPLD */
/* FPGA program pin configuration */
-#define CFG_FPGA_PRG 0x04000000 /* JTAG TMS pin (ppc output) */
-#define CFG_FPGA_CLK 0x02000000 /* JTAG TCK pin (ppc output) */
-#define CFG_FPGA_DATA 0x01000000 /* JTAG TDO->TDI data pin (ppc output) */
-#define CFG_FPGA_INIT 0x00010000 /* unused (ppc input) */
-#define CFG_FPGA_DONE 0x00008000 /* JTAG TDI->TDO pin (ppc input) */
+#define CFG_FPGA_PRG 0x04000000 /* JTAG TMS pin (ppc output) */
+#define CFG_FPGA_CLK 0x02000000 /* JTAG TCK pin (ppc output) */
+#define CFG_FPGA_DATA 0x01000000 /* JTAG TDO->TDI data pin (ppc output) */
+#define CFG_FPGA_INIT 0x00010000 /* unused (ppc input) */
+#define CFG_FPGA_DONE 0x00008000 /* JTAG TDI->TDO pin (ppc input) */
/*-----------------------------------------------------------------------
* Definitions for initial stack pointer and data area (in data cache)
*/
/* use on chip memory ( OCM ) for temperary stack until sdram is tested */
-#define CFG_TEMP_STACK_OCM 1
+#define CFG_TEMP_STACK_OCM 1
/* On Chip Memory location */
#define CFG_OCM_DATA_ADDR 0xF8000000
@@ -292,13 +292,13 @@
#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
/*-----------------------------------------------------------------------
* Definitions for GPIO setup (PPC405EP specific)
*
- * GPIO0[0] - External Bus Controller BLAST output
- * GPIO0[1-9] - Instruction trace outputs -> GPIO
+ * GPIO0[0] - External Bus Controller BLAST output
+ * GPIO0[1-9] - Instruction trace outputs -> GPIO
* GPIO0[10-13] - External Bus Controller CS_1 - CS_4 outputs
* GPIO0[14-16] - External Bus Controller ABUS3-ABUS5 outputs -> GPIO
* GPIO0[17-23] - External Interrupts IRQ0 - IRQ6 inputs
@@ -306,17 +306,17 @@
* GPIO0[28-29] - UART1 data signal input/output
* GPIO0[30-31] - EMAC0 and EMAC1 reject packet inputs
*/
-/* GPIO Input: OSR=00, ISR=00, TSR=00, TCR=0 */
-/* GPIO Output: OSR=00, ISR=00, TSR=00, TCR=1 */
-/* Alt. Funtion Input: OSR=00, ISR=01, TSR=00, TCR=0 */
+/* GPIO Input: OSR=00, ISR=00, TSR=00, TCR=0 */
+/* GPIO Output: OSR=00, ISR=00, TSR=00, TCR=1 */
+/* Alt. Funtion Input: OSR=00, ISR=01, TSR=00, TCR=0 */
/* Alt. Funtion Output: OSR=01, ISR=00, TSR=00, TCR=1 */
-#define CFG_GPIO0_OSRH 0x40000540 /* 0 ... 15 */
-#define CFG_GPIO0_OSRL 0x00000110 /* 16 ... 31 */
-#define CFG_GPIO0_ISR1H 0x00000000 /* 0 ... 15 */
-#define CFG_GPIO0_ISR1L 0x14000045 /* 16 ... 31 */
-#define CFG_GPIO0_TSRH 0x00000000 /* 0 ... 15 */
-#define CFG_GPIO0_TSRL 0x00000000 /* 16 ... 31 */
-#define CFG_GPIO0_TCR 0xF7FE0014 /* 0 ... 31 */
+#define CFG_GPIO0_OSRH 0x40000540 /* 0 ... 15 */
+#define CFG_GPIO0_OSRL 0x00000110 /* 16 ... 31 */
+#define CFG_GPIO0_ISR1H 0x00000000 /* 0 ... 15 */
+#define CFG_GPIO0_ISR1L 0x14000045 /* 16 ... 31 */
+#define CFG_GPIO0_TSRH 0x00000000 /* 0 ... 15 */
+#define CFG_GPIO0_TSRL 0x00000000 /* 16 ... 31 */
+#define CFG_GPIO0_TCR 0xF7FE0014 /* 0 ... 31 */
/*
* Internal Definitions
@@ -331,16 +331,16 @@
* This value will be set if iic boot eprom is disabled.
*/
#if 0
-#define PLLMR0_DEFAULT PLLMR0_266_133_66_33
-#define PLLMR1_DEFAULT PLLMR1_266_133_66_33
+#define PLLMR0_DEFAULT PLLMR0_266_133_66_33
+#define PLLMR1_DEFAULT PLLMR1_266_133_66_33
#endif
#if 0
-#define PLLMR0_DEFAULT PLLMR0_200_100_50_33
-#define PLLMR1_DEFAULT PLLMR1_200_100_50_33
+#define PLLMR0_DEFAULT PLLMR0_200_100_50_33
+#define PLLMR1_DEFAULT PLLMR1_200_100_50_33
#endif
#if 1
-#define PLLMR0_DEFAULT PLLMR0_133_66_66_33
-#define PLLMR1_DEFAULT PLLMR1_133_66_66_33
+#define PLLMR0_DEFAULT PLLMR0_133_66_66_33
+#define PLLMR1_DEFAULT PLLMR1_133_66_66_33
#endif
#endif /* __CONFIG_H */
diff --git a/include/configs/DU405.h b/include/configs/DU405.h
index 3e5fc3f..5a5415a 100644
--- a/include/configs/DU405.h
+++ b/include/configs/DU405.h
@@ -34,12 +34,12 @@
*/
#define CONFIG_405GP 1 /* This is a PPC405 CPU */
-#define CONFIG_4xx 1 /* ...member of PPC4xx family */
-#define CONFIG_DU405 1 /* ...on a DU405 board */
+#define CONFIG_4xx 1 /* ...member of PPC4xx family */
+#define CONFIG_DU405 1 /* ...on a DU405 board */
-#define CONFIG_BOARD_PRE_INIT 1 /* call board_pre_init() */
+#define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */
-#define CONFIG_SYS_CLK_FREQ 25000000 /* external frequency to pll */
+#define CONFIG_SYS_CLK_FREQ 25000000 /* external frequency to pll */
#define CONFIG_BAUDRATE 9600
#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */
@@ -51,7 +51,7 @@
#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
#define CONFIG_MII 1 /* MII PHY management */
-#define CONFIG_PHY_ADDR 0 /* PHY address */
+#define CONFIG_PHY_ADDR 0 /* PHY address */
#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \
CFG_CMD_PCI | \
@@ -59,7 +59,7 @@
CFG_CMD_IDE | \
CFG_CMD_ELF | \
CFG_CMD_DATE | \
- CFG_CMD_EEPROM )
+ CFG_CMD_EEPROM )
#define CONFIG_MAC_PARTITION
#define CONFIG_DOS_PARTITION
@@ -69,10 +69,10 @@
#undef CONFIG_WATCHDOG /* watchdog disabled */
-#define CONFIG_RTC_MC146818 /* BQ3285 is MC146818 compatible*/
-#define CFG_RTC_REG_BASE_ADDR 0xF0000080 /* RTC Base Address */
+#define CONFIG_RTC_MC146818 /* BQ3285 is MC146818 compatible*/
+#define CFG_RTC_REG_BASE_ADDR 0xF0000080 /* RTC Base Address */
-#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */
+#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */
/*
* Miscellaneous configurable options
@@ -80,30 +80,30 @@
#define CFG_LONGHELP /* undef to save memory */
#define CFG_PROMPT "=> " /* Monitor Command Prompt */
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
#endif
#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
#define CFG_MAXARGS 16 /* max number of command args */
#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
+#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-#define CFG_EXT_SERIAL_CLOCK 11059200 /* use external serial clock */
+#define CFG_EXT_SERIAL_CLOCK 11059200 /* use external serial clock */
/* The following table includes the supported baudrates */
-#define CFG_BAUDRATE_TABLE \
+#define CFG_BAUDRATE_TABLE \
{ 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \
57600, 115200, 230400, 460800, 921600 }
#define CFG_LOAD_ADDR 0x100000 /* default load address */
#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
@@ -111,44 +111,44 @@
* PCI stuff
*-----------------------------------------------------------------------
*/
-#define PCI_HOST_ADAPTER 0 /* configure ar pci adapter */
-#define PCI_HOST_FORCE 1 /* configure as pci host */
-#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
+#define PCI_HOST_ADAPTER 0 /* configure ar pci adapter */
+#define PCI_HOST_FORCE 1 /* configure as pci host */
+#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
-#define CONFIG_PCI /* include pci support */
-#define CONFIG_PCI_HOST PCI_HOST_AUTO /* select pci host function */
-#define CONFIG_PCI_PNP /* do pci plug-and-play */
- /* resource configuration */
+#define CONFIG_PCI /* include pci support */
+#define CONFIG_PCI_HOST PCI_HOST_AUTO /* select pci host function */
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
+ /* resource configuration */
-#define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */
+#define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */
-#define CONFIG_PCI_BOOTDELAY 0 /* enable pci bootdelay variable*/
+#define CONFIG_PCI_BOOTDELAY 0 /* enable pci bootdelay variable*/
-#define CFG_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */
-#define CFG_PCI_SUBSYS_DEVICEID 0x0404 /* PCI Device ID: CPCI-ISER4 */
-#define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */
-#define CFG_PCI_PTM1MS 0xff000001 /* 16MB, enable hard-wired to 1 */
-#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
-#define CFG_PCI_PTM2LA 0xffe00000 /* point to flash */
-#define CFG_PCI_PTM2MS 0xffe00001 /* 2MB, enable */
-#define CFG_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */
+#define CFG_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */
+#define CFG_PCI_SUBSYS_DEVICEID 0x0404 /* PCI Device ID: CPCI-ISER4 */
+#define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */
+#define CFG_PCI_PTM1MS 0xff000001 /* 16MB, enable hard-wired to 1 */
+#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
+#define CFG_PCI_PTM2LA 0xffe00000 /* point to flash */
+#define CFG_PCI_PTM2MS 0xffe00001 /* 2MB, enable */
+#define CFG_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */
/*-----------------------------------------------------------------------
* IDE/ATA stuff
*-----------------------------------------------------------------------
*/
-#undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */
-#undef CONFIG_IDE_LED /* no led for ide supported */
-#undef CONFIG_IDE_RESET /* no reset for ide supported */
+#undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */
+#undef CONFIG_IDE_LED /* no led for ide supported */
+#undef CONFIG_IDE_RESET /* no reset for ide supported */
-#define CFG_IDE_MAXBUS 1 /* max. 1 IDE busses */
-#define CFG_IDE_MAXDEVICE (CFG_IDE_MAXBUS*1) /* max. 1 drives per IDE bus */
+#define CFG_IDE_MAXBUS 1 /* max. 1 IDE busses */
+#define CFG_IDE_MAXDEVICE (CFG_IDE_MAXBUS*1) /* max. 1 drives per IDE bus */
-#define CFG_ATA_BASE_ADDR 0xF0100000
-#define CFG_ATA_IDE0_OFFSET 0x0000
+#define CFG_ATA_BASE_ADDR 0xF0100000
+#define CFG_ATA_IDE0_OFFSET 0x0000
#define CFG_ATA_DATA_OFFSET 0x0000 /* Offset for data I/O */
-#define CFG_ATA_REG_OFFSET 0x0000 /* Offset for normal register accesses */
+#define CFG_ATA_REG_OFFSET 0x0000 /* Offset for normal register accesses */
#define CFG_ATA_ALT_OFFSET 0x0000 /* Offset for alternate registers */
/*-----------------------------------------------------------------------
@@ -177,18 +177,18 @@
#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
-#define CFG_FLASH_WORD_SIZE unsigned short /* flash word size (width) */
-#define CFG_FLASH_ADDR0 0x5555 /* 1st address for flash config cycles */
-#define CFG_FLASH_ADDR1 0x2AAA /* 2nd address for flash config cycles */
+#define CFG_FLASH_WORD_SIZE unsigned short /* flash word size (width) */
+#define CFG_FLASH_ADDR0 0x5555 /* 1st address for flash config cycles */
+#define CFG_FLASH_ADDR1 0x2AAA /* 2nd address for flash config cycles */
/*
* The following defines are added for buggy IOP480 byte interface.
* All other boards should use the standard values (CPCI405 etc.)
*/
-#define CFG_FLASH_READ0 0x0000 /* 0 is standard */
-#define CFG_FLASH_READ1 0x0001 /* 1 is standard */
-#define CFG_FLASH_READ2 0x0002 /* 2 is standard */
+#define CFG_FLASH_READ0 0x0000 /* 0 is standard */
+#define CFG_FLASH_READ1 0x0001 /* 1 is standard */
+#define CFG_FLASH_READ2 0x0002 /* 2 is standard */
-#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
+#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
/*-----------------------------------------------------------------------
* I2C EEPROM (CAT24WC08) for environment
@@ -198,18 +198,18 @@
#define CFG_I2C_SLAVE 0x7F
#define CFG_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC08 */
-#define CFG_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
-/* mask of address bits that overflow into the "EEPROM chip address" */
+#define CFG_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
+/* mask of address bits that overflow into the "EEPROM chip address" */
#define CFG_I2C_EEPROM_ADDR_OVERFLOW 0x07
#define CFG_EEPROM_PAGE_WRITE_BITS 4 /* The Catalyst CAT24WC08 has */
/* 16 byte page write mode using*/
- /* last 4 bits of the address */
+ /* last 4 bits of the address */
#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
#define CFG_EEPROM_PAGE_WRITE_ENABLE
-#define CFG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
-#define CFG_ENV_OFFSET 0x000 /* environment starts at the beginning of the EEPROM */
-#define CFG_ENV_SIZE 0x400 /* 1024 bytes may be used for env vars */
+#define CFG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
+#define CFG_ENV_OFFSET 0x000 /* environment starts at the beginning of the EEPROM */
+#define CFG_ENV_SIZE 0x400 /* 1024 bytes may be used for env vars */
/* total size of a CAT24WC08 is 1024 bytes */
/*-----------------------------------------------------------------------
@@ -234,48 +234,48 @@
* External Bus Controller (EBC) Setup
*/
-#define FLASH0_BA 0xFFC00000 /* FLASH 0 Base Address */
-#define FLASH1_BA 0xFF800000 /* FLASH 1 Base Address */
-#define CAN_BA 0xF0000000 /* CAN Base Address */
-#define DUART_BA 0xF0300000 /* DUART Base Address */
-#define CF_BA 0xF0100000 /* CompactFlash Base Address */
-#define SRAM_BA 0xF0200000 /* SRAM Base Address */
-#define DURAG_IO_BA 0xF0400000 /* DURAG Bus IO Base Address */
-#define DURAG_MEM_BA 0xF0500000 /* DURAG Bus Mem Base Address */
+#define FLASH0_BA 0xFFC00000 /* FLASH 0 Base Address */
+#define FLASH1_BA 0xFF800000 /* FLASH 1 Base Address */
+#define CAN_BA 0xF0000000 /* CAN Base Address */
+#define DUART_BA 0xF0300000 /* DUART Base Address */
+#define CF_BA 0xF0100000 /* CompactFlash Base Address */
+#define SRAM_BA 0xF0200000 /* SRAM Base Address */
+#define DURAG_IO_BA 0xF0400000 /* DURAG Bus IO Base Address */
+#define DURAG_MEM_BA 0xF0500000 /* DURAG Bus Mem Base Address */
-#define FPGA_MODE_REG (DUART_BA+0x80) /* FPGA Mode Register */
+#define FPGA_MODE_REG (DUART_BA+0x80) /* FPGA Mode Register */
-/* Memory Bank 0 (Flash Bank 0) initialization */
-#define CFG_EBC_PB0AP 0x92015480
-#define CFG_EBC_PB0CR FLASH0_BA | 0x5A000 /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
+/* Memory Bank 0 (Flash Bank 0) initialization */
+#define CFG_EBC_PB0AP 0x92015480
+#define CFG_EBC_PB0CR FLASH0_BA | 0x5A000 /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
-/* Memory Bank 1 (Flash Bank 1) initialization */
-#define CFG_EBC_PB1AP 0x92015480
-#define CFG_EBC_PB1CR FLASH1_BA | 0x5A000 /* BAS=0xFF8,BS=4MB,BU=R/W,BW=16bit */
+/* Memory Bank 1 (Flash Bank 1) initialization */
+#define CFG_EBC_PB1AP 0x92015480
+#define CFG_EBC_PB1CR FLASH1_BA | 0x5A000 /* BAS=0xFF8,BS=4MB,BU=R/W,BW=16bit */
-/* Memory Bank 2 (CAN0) initialization */
-#define CFG_EBC_PB2AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
-#define CFG_EBC_PB2CR CAN_BA | 0x18000 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */
+/* Memory Bank 2 (CAN0) initialization */
+#define CFG_EBC_PB2AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
+#define CFG_EBC_PB2CR CAN_BA | 0x18000 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */
-/* Memory Bank 3 (DUART) initialization */
-#define CFG_EBC_PB3AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
-#define CFG_EBC_PB3CR DUART_BA | 0x18000 /* BAS=0xF03,BS=1MB,BU=R/W,BW=8bit */
+/* Memory Bank 3 (DUART) initialization */
+#define CFG_EBC_PB3AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
+#define CFG_EBC_PB3CR DUART_BA | 0x18000 /* BAS=0xF03,BS=1MB,BU=R/W,BW=8bit */
-/* Memory Bank 4 (CompactFlash IDE) initialization */
-#define CFG_EBC_PB4AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
-#define CFG_EBC_PB4CR CF_BA | 0x1A000 /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */
+/* Memory Bank 4 (CompactFlash IDE) initialization */
+#define CFG_EBC_PB4AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
+#define CFG_EBC_PB4CR CF_BA | 0x1A000 /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */
-/* Memory Bank 5 (SRAM) initialization */
-#define CFG_EBC_PB5AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
-#define CFG_EBC_PB5CR SRAM_BA | 0x1A000 /* BAS=0xF02,BS=1MB,BU=R/W,BW=16bit */
+/* Memory Bank 5 (SRAM) initialization */
+#define CFG_EBC_PB5AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
+#define CFG_EBC_PB5CR SRAM_BA | 0x1A000 /* BAS=0xF02,BS=1MB,BU=R/W,BW=16bit */
-/* Memory Bank 6 (DURAG Bus IO Space) initialization */
-#define CFG_EBC_PB6AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
-#define CFG_EBC_PB6CR DURAG_IO_BA | 0x18000 /* BAS=0xF04,BS=1MB,BU=R/W,BW=8bit*/
+/* Memory Bank 6 (DURAG Bus IO Space) initialization */
+#define CFG_EBC_PB6AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
+#define CFG_EBC_PB6CR DURAG_IO_BA | 0x18000 /* BAS=0xF04,BS=1MB,BU=R/W,BW=8bit*/
-/* Memory Bank 7 (DURAG Bus Mem Space) initialization */
-#define CFG_EBC_PB7AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
-#define CFG_EBC_PB7CR DURAG_MEM_BA | 0x18000 /* BAS=0xF05,BS=1MB,BU=R/W,BW=8bit */
+/* Memory Bank 7 (DURAG Bus Mem Space) initialization */
+#define CFG_EBC_PB7AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
+#define CFG_EBC_PB7CR DURAG_MEM_BA | 0x18000 /* BAS=0xF05,BS=1MB,BU=R/W,BW=8bit */
/*-----------------------------------------------------------------------
@@ -283,7 +283,7 @@
*/
/* use on chip memory ( OCM ) for temperary stack until sdram is tested */
-#define CFG_TEMP_STACK_OCM 1
+#define CFG_TEMP_STACK_OCM 1
/* On Chip Memory location */
#define CFG_OCM_DATA_ADDR 0xF8000000
@@ -293,7 +293,7 @@
#define CFG_INIT_RAM_END CFG_OCM_DATA_SIZE /* End of used area in RAM */
#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
/*
diff --git a/include/configs/EBONY.h b/include/configs/EBONY.h
index aecb3c2..46e729f 100644
--- a/include/configs/EBONY.h
+++ b/include/configs/EBONY.h
@@ -32,7 +32,7 @@
*----------------------------------------------------------------------*/
#define CONFIG_EBONY 1 /* Board is ebony */
#define CONFIG_4xx 1 /* ... PPC4xx family */
-#define CONFIG_BOARD_PRE_INIT 1 /* Call board_pre_init */
+#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
#undef CFG_DRAM_TEST /* Disable-takes long time! */
#define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */
diff --git a/include/configs/ELPT860.h b/include/configs/ELPT860.h
index 2f253b9..5bfdc9b 100644
--- a/include/configs/ELPT860.h
+++ b/include/configs/ELPT860.h
@@ -19,7 +19,7 @@
**
** This program is distributed in the hope that it will be useful,
** but WITHOUT ANY WARRANTY; without even the implied warranty of
-** MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+** MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
** GNU General Public License for more details.
**
** You should have received a copy of the GNU General Public License
@@ -47,26 +47,26 @@
#define CONFIG_MPC860T 1
#define CONFIG_ELPT860 1 /* ...on a LEOX's ELPT860 CPU board */
-#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */
+#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */
#undef CONFIG_8xx_CONS_SMC2
#undef CONFIG_8xx_CONS_NONE
-#define CONFIG_CLOCKS_IN_MHZ 1 /* Clock passed to Linux (<2.4.5) in MHz */
-#define CONFIG_8xx_GCLK_FREQ 50000000 /* MPC860T runs at 50MHz */
+#define CONFIG_CLOCKS_IN_MHZ 1 /* Clock passed to Linux (<2.4.5) in MHz */
+#define CONFIG_8xx_GCLK_FREQ 50000000 /* MPC860T runs at 50MHz */
#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-#define CONFIG_BOARD_PRE_INIT 1 /* Call board_pre_init */
+#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
/* BOOT arguments */
-#define CONFIG_PREBOOT \
- "echo;" \
- "echo Type \"run nfsboot\" to mount root filesystem over NFS;" \
+#define CONFIG_PREBOOT \
+ "echo;" \
+ "echo Type \"run nfsboot\" to mount root filesystem over NFS;" \
"echo"
#undef CONFIG_BOOTARGS
-#define CONFIG_EXTRA_ENV_SETTINGS \
+#define CONFIG_EXTRA_ENV_SETTINGS \
"ramargs=setenv bootargs root=/dev/ram rw\0" \
"rootargs=setenv rootpath /tftp/$(ipaddr)\0" \
"nfsargs=setenv bootargs root=/dev/nfs rw " \
@@ -86,14 +86,14 @@
#undef CONFIG_WATCHDOG /* watchdog disabled */
#undef CONFIG_CAN_DRIVER /* CAN Driver support disabled */
#undef CONFIG_RTC_MPC8xx /* internal RTC MPC8xx unused */
-#define CONFIG_RTC_DS164x 1 /* RTC is a Dallas DS1646 */
+#define CONFIG_RTC_DS164x 1 /* RTC is a Dallas DS1646 */
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#undef CFG_LOADS_BAUD_CHANGE /* don't allow baudrate change */
-#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \
+#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \
CFG_CMD_ASKENV | \
- CFG_CMD_DATE )
+ CFG_CMD_DATE )
/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
#include <cmd_confdefs.h>
@@ -101,8 +101,8 @@
/*
* Miscellaneous configurable options
*/
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "LEOX_elpt860: " /* Monitor Command Prompt */
+#define CFG_LONGHELP /* undef to save memory */
+#define CFG_PROMPT "LEOX_elpt860: " /* Monitor Command Prompt */
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
# define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
@@ -110,35 +110,35 @@
# define CFG_CBSIZE 256 /* Console I/O Buffer Size */
#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
#define CFG_MEMTEST_START 0x00400000 /* memtest works on */
#define CFG_MEMTEST_END 0x00C00000 /* 4 ... 12 MB in DRAM */
-#define CFG_LOAD_ADDR 0x00100000 /* default load address */
+#define CFG_LOAD_ADDR 0x00100000 /* default load address */
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
/*
* Environment Variables and Storages
*/
-#define CONFIG_ENV_OVERWRITE 1 /* Allow Overwrite of serial# & ethaddr */
+#define CONFIG_ENV_OVERWRITE 1 /* Allow Overwrite of serial# & ethaddr */
-#undef CFG_ENV_IS_IN_NVRAM /* Environment is in NVRAM */
-#undef CFG_ENV_IS_IN_EEPROM /* Environment is in I2C EEPROM */
-#define CFG_ENV_IS_IN_FLASH 1 /* Environment is in FLASH */
+#undef CFG_ENV_IS_IN_NVRAM /* Environment is in NVRAM */
+#undef CFG_ENV_IS_IN_EEPROM /* Environment is in I2C EEPROM */
+#define CFG_ENV_IS_IN_FLASH 1 /* Environment is in FLASH */
-#define CONFIG_BAUDRATE 9600 /* console baudrate = 9600 bps */
+#define CONFIG_BAUDRATE 9600 /* console baudrate = 9600 bps */
#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
-#define CONFIG_ETHADDR 00:01:77:00:60:40
-#define CONFIG_IPADDR 192.168.0.30
-#define CONFIG_NETMASK 255.255.255.0
+#define CONFIG_ETHADDR 00:01:77:00:60:40
+#define CONFIG_IPADDR 192.168.0.30
+#define CONFIG_NETMASK 255.255.255.0
-#define CONFIG_SERVERIP 192.168.0.1
-#define CONFIG_GATEWAYIP 192.168.0.1
+#define CONFIG_SERVERIP 192.168.0.1
+#define CONFIG_GATEWAYIP 192.168.0.1
/*
* Low Level Configuration Settings
@@ -155,19 +155,19 @@
* Definitions for initial stack pointer and data area (in DPRAM)
*/
#define CFG_INIT_RAM_ADDR CFG_IMMR
-#define CFG_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */
-#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */
+#define CFG_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */
+#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
/*-----------------------------------------------------------------------
* Start addresses for the final memory configuration
* (Set up by the startup code)
* Please note that CFG_SDRAM_BASE _must_ start at 0
*/
-#define CFG_SDRAM_BASE 0x00000000
+#define CFG_SDRAM_BASE 0x00000000
#define CFG_FLASH_BASE 0x02000000
-#define CFG_NVRAM_BASE 0x03000000
+#define CFG_NVRAM_BASE 0x03000000
#if defined(CFG_ENV_IS_IN_FLASH)
# if defined(DEBUG)
@@ -184,48 +184,48 @@
#endif
#define CFG_MONITOR_BASE CFG_FLASH_BASE
-#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
+#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
/*-----------------------------------------------------------------------
* FLASH organization
*/
-#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
#define CFG_MAX_FLASH_SECT 8 /* max number of sectors on one chip */
#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
#if defined(CFG_ENV_IS_IN_FLASH)
-# define CFG_ENV_OFFSET 0x10000 /* Offset of Environment Sector */
-# define CFG_ENV_SIZE 0x10000 /* Total Size of Environment Sector */
+# define CFG_ENV_OFFSET 0x10000 /* Offset of Environment Sector */
+# define CFG_ENV_SIZE 0x10000 /* Total Size of Environment Sector */
#endif
/*-----------------------------------------------------------------------
* NVRAM organization
*/
-#define CFG_NVRAM_BASE_ADDR CFG_NVRAM_BASE /* Base address of NVRAM area */
-#define CFG_NVRAM_SIZE ((128*1024)-8) /* clock regs resident in the */
+#define CFG_NVRAM_BASE_ADDR CFG_NVRAM_BASE /* Base address of NVRAM area */
+#define CFG_NVRAM_SIZE ((128*1024)-8) /* clock regs resident in the */
/* 8 top NVRAM locations */
#if defined(CFG_ENV_IS_IN_NVRAM)
-# define CFG_ENV_ADDR CFG_NVRAM_BASE /* Base address of NVRAM area */
-# define CFG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */
+# define CFG_ENV_ADDR CFG_NVRAM_BASE /* Base address of NVRAM area */
+# define CFG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */
#endif
/*-----------------------------------------------------------------------
* Cache Configuration
*/
-#define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
+#define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-# define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */
+# define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */
#endif
/*-----------------------------------------------------------------------
@@ -235,10 +235,10 @@
* Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
*/
#if defined(CONFIG_WATCHDOG)
-# define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
+# define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
SYPCR_SWE | SYPCR_SWRI | SYPCR_SWP)
#else
-# define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
+# define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
SYPCR_SWP)
#endif
@@ -309,7 +309,7 @@
* BR0 and OR0 (FLASH)
*/
-#define FLASH_BASE0_PRELIM CFG_FLASH_BASE /* FLASH bank #0 */
+#define FLASH_BASE0_PRELIM CFG_FLASH_BASE /* FLASH bank #0 */
/* used to re-map FLASH both when starting from SRAM or FLASH:
* restrict access enough to keep SRAM working (if any)
@@ -327,10 +327,10 @@
* BR1 and OR1 (SDRAM)
*
*/
-#define SDRAM_BASE1_PRELIM CFG_SDRAM_BASE /* SDRAM bank #0 */
-#define SDRAM_MAX_SIZE 0x02000000 /* 32 MB MAX for CS1 */
+#define SDRAM_BASE1_PRELIM CFG_SDRAM_BASE /* SDRAM bank #0 */
+#define SDRAM_MAX_SIZE 0x02000000 /* 32 MB MAX for CS1 */
-/* SDRAM timing: */
+/* SDRAM timing: */
#define CFG_OR_TIMING_SDRAM 0x00000000
#define CFG_OR1_PRELIM ((2 * CFG_PRELIM_OR_AM) | CFG_OR_TIMING_SDRAM )
@@ -340,10 +340,10 @@
* BR2 and OR2 (NVRAM)
*
*/
-#define NVRAM_BASE1_PRELIM CFG_NVRAM_BASE /* NVRAM bank #0 */
-#define NVRAM_MAX_SIZE 0x00020000 /* 128 KB MAX for CS2 */
+#define NVRAM_BASE1_PRELIM CFG_NVRAM_BASE /* NVRAM bank #0 */
+#define NVRAM_MAX_SIZE 0x00020000 /* 128 KB MAX for CS2 */
-#define CFG_OR2_PRELIM 0xFFF80160
+#define CFG_OR2_PRELIM 0xFFF80160
#define CFG_BR2_PRELIM ((NVRAM_BASE1_PRELIM & BR_BA_MSK) | BR_PS_8 | BR_V )
/*
@@ -351,15 +351,15 @@
*/
/* periodic timer for refresh */
-#define CFG_MAMR_PTA 97 /* start with divider for 100 MHz */
+#define CFG_MAMR_PTA 97 /* start with divider for 100 MHz */
/* refresh rate 15.6 us (= 64 ms / 4K = 62.4 / quad bursts) for <= 128 MBit */
#define CFG_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */
-#define CFG_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */
+#define CFG_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */
-/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */
-#define CFG_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */
-#define CFG_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */
+/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */
+#define CFG_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */
+#define CFG_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */
/*
* MAMR settings for SDRAM
@@ -383,8 +383,8 @@
/*
* Boot Flags
*/
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
#endif /* __CONFIG_H */
diff --git a/include/configs/ERIC.h b/include/configs/ERIC.h
index 539716f..1643dee 100644
--- a/include/configs/ERIC.h
+++ b/include/configs/ERIC.h
@@ -37,7 +37,7 @@
#define CONFIG_4xx 1 /* ...member of PPC4xx family */
#define CONFIG_ERIC 1 /* ...on a ERIC board */
-#define CONFIG_BOARD_PRE_INIT 1 /* run board_pre_init() */
+#define CONFIG_BOARD_EARLY_INIT_F 1 /* run board_early_init_f() */
#define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */
diff --git a/include/configs/EVB64260.h b/include/configs/EVB64260.h
index af5122f..9baf252 100644
--- a/include/configs/EVB64260.h
+++ b/include/configs/EVB64260.h
@@ -51,7 +51,7 @@
/* which initialization functions to call for this board */
#define CONFIG_MISC_INIT_R 1
-#define CONFIG_BOARD_PRE_INIT 1
+#define CONFIG_BOARD_EARLY_INIT_F 1
#ifndef CONFIG_EVB64260_750CX
#define CFG_BOARD_NAME "EVB64260"
diff --git a/include/configs/EXBITGEN.h b/include/configs/EXBITGEN.h
index 4e70519..d85be42 100644
--- a/include/configs/EXBITGEN.h
+++ b/include/configs/EXBITGEN.h
@@ -1,5 +1,5 @@
/*
- * (C) Copyright 2000
+ * (C) Copyright 2000-2004
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*
* See file CREDITS for list of people who contributed to this
@@ -37,7 +37,7 @@
#define CONFIG_4xx 1 /* ...member of PPC4xx family */
#define CONFIG_EXBITGEN 1 /* on a Exbit Generic board */
-#define CONFIG_BOARD_PRE_INIT 1 /* Call board_pre_init */
+#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
#define CONFIG_SYS_CLK_FREQ 25000000 /* external frequency to pll */
diff --git a/include/configs/HUB405.h b/include/configs/HUB405.h
index e4dbc7a..ff0d8d0 100644
--- a/include/configs/HUB405.h
+++ b/include/configs/HUB405.h
@@ -34,13 +34,13 @@
*/
#define CONFIG_405EP 1 /* This is a PPC405 CPU */
-#define CONFIG_4xx 1 /* ...member of PPC4xx family */
-#define CONFIG_HUB405 1 /* ...on a ASH405 board */
+#define CONFIG_4xx 1 /* ...member of PPC4xx family */
+#define CONFIG_HUB405 1 /* ...on a ASH405 board */
-#define CONFIG_BOARD_PRE_INIT 1 /* call board_pre_init() */
-#define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */
+#define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */
+#define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */
-#define CONFIG_SYS_CLK_FREQ 33333334 /* external frequency to pll */
+#define CONFIG_SYS_CLK_FREQ 33333334 /* external frequency to pll */
#define CONFIG_BAUDRATE 9600
#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */
@@ -60,7 +60,7 @@
#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
#define CONFIG_MII 1 /* MII PHY management */
-#define CONFIG_PHY_ADDR 0 /* PHY address */
+#define CONFIG_PHY_ADDR 0 /* PHY address */
#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \
CFG_CMD_DHCP | \
@@ -70,14 +70,14 @@
CFG_CMD_I2C | \
CFG_CMD_MII | \
CFG_CMD_PING | \
- CFG_CMD_EEPROM )
+ CFG_CMD_EEPROM )
/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
#include <cmd_confdefs.h>
-#undef CONFIG_WATCHDOG /* watchdog disabled */
+#undef CONFIG_WATCHDOG /* watchdog disabled */
-#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */
+#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */
/*
* Miscellaneous configurable options
@@ -87,45 +87,45 @@
#undef CFG_HUSH_PARSER /* use "hush" command parser */
#ifdef CFG_HUSH_PARSER
-#define CFG_PROMPT_HUSH_PS2 "> "
+#define CFG_PROMPT_HUSH_PS2 "> "
#endif
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
#endif
#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
#define CFG_MAXARGS 16 /* max number of command args */
#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_DEVICE_NULLDEV 1 /* include nulldev device */
+#define CFG_DEVICE_NULLDEV 1 /* include nulldev device */
-#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
+#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-#undef CFG_EXT_SERIAL_CLOCK /* no external serial clock used */
-#define CFG_IGNORE_405_UART_ERRATA_59 /* ignore ppc405gp errata #59 */
-#define CFG_BASE_BAUD 691200
-#undef CONFIG_UART1_CONSOLE /* define for uart1 as console */
+#undef CFG_EXT_SERIAL_CLOCK /* no external serial clock used */
+#define CFG_IGNORE_405_UART_ERRATA_59 /* ignore ppc405gp errata #59 */
+#define CFG_BASE_BAUD 691200
+#undef CONFIG_UART1_CONSOLE /* define for uart1 as console */
/* The following table includes the supported baudrates */
-#define CFG_BAUDRATE_TABLE \
+#define CFG_BAUDRATE_TABLE \
{ 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \
57600, 115200, 230400, 460800, 921600 }
#define CFG_LOAD_ADDR 0x100000 /* default load address */
#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
+#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
-#define CFG_RX_ETH_BUFFER 16 /* use 16 rx buffer on 405 emac */
+#define CFG_RX_ETH_BUFFER 16 /* use 16 rx buffer on 405 emac */
/*-----------------------------------------------------------------------
* NAND-FLASH stuff
@@ -138,14 +138,14 @@
#define ADDR_PAGE 2
#define ADDR_COLUMN_PAGE 3
-#define NAND_ChipID_UNKNOWN 0x00
+#define NAND_ChipID_UNKNOWN 0x00
#define NAND_MAX_FLOORS 1
#define NAND_MAX_CHIPS 1
-#define CFG_NAND_CE (0x80000000 >> 1) /* our CE is GPIO1 */
-#define CFG_NAND_CLE (0x80000000 >> 2) /* our CLE is GPIO2 */
-#define CFG_NAND_ALE (0x80000000 >> 3) /* our ALE is GPIO3 */
-#define CFG_NAND_RDY (0x80000000 >> 4) /* our RDY is GPIO4 */
+#define CFG_NAND_CE (0x80000000 >> 1) /* our CE is GPIO1 */
+#define CFG_NAND_CLE (0x80000000 >> 2) /* our CLE is GPIO2 */
+#define CFG_NAND_ALE (0x80000000 >> 3) /* our ALE is GPIO3 */
+#define CFG_NAND_RDY (0x80000000 >> 4) /* our RDY is GPIO4 */
#define NAND_DISABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CE);} while(0)
#define NAND_ENABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CE);} while(0)
@@ -164,26 +164,26 @@
* PCI stuff
*-----------------------------------------------------------------------
*/
-#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */
-#define PCI_HOST_FORCE 1 /* configure as pci host */
-#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
+#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */
+#define PCI_HOST_FORCE 1 /* configure as pci host */
+#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
-#undef CONFIG_PCI /* include pci support */
-#define CONFIG_PCI_HOST PCI_HOST_HOST /* select pci host function */
-#undef CONFIG_PCI_PNP /* do pci plug-and-play */
- /* resource configuration */
+#undef CONFIG_PCI /* include pci support */
+#define CONFIG_PCI_HOST PCI_HOST_HOST /* select pci host function */
+#undef CONFIG_PCI_PNP /* do pci plug-and-play */
+ /* resource configuration */
-#undef CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */
+#undef CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */
-#define CFG_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */
-#define CFG_PCI_SUBSYS_DEVICEID 0x0405 /* PCI Device ID: CPCI-405 */
-#define CFG_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/
-#define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */
-#define CFG_PCI_PTM1MS 0xfc000001 /* 64MB, enable hard-wired to 1 */
-#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
-#define CFG_PCI_PTM2LA 0xffc00000 /* point to flash */
-#define CFG_PCI_PTM2MS 0xffc00001 /* 4MB, enable */
-#define CFG_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */
+#define CFG_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */
+#define CFG_PCI_SUBSYS_DEVICEID 0x0405 /* PCI Device ID: CPCI-405 */
+#define CFG_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/
+#define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */
+#define CFG_PCI_PTM1MS 0xfc000001 /* 64MB, enable hard-wired to 1 */
+#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
+#define CFG_PCI_PTM2LA 0xffc00000 /* point to flash */
+#define CFG_PCI_PTM2MS 0xffc00001 /* 4MB, enable */
+#define CFG_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */
/*-----------------------------------------------------------------------
* Start addresses for the final memory configuration
@@ -211,34 +211,34 @@
#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
#define CFG_FLASH_WRITE_TOUT 1000 /* Timeout for Flash Write (in ms) */
-#define CFG_FLASH_WORD_SIZE unsigned short /* flash word size (width) */
-#define CFG_FLASH_ADDR0 0x5555 /* 1st address for flash config cycles */
-#define CFG_FLASH_ADDR1 0x2AAA /* 2nd address for flash config cycles */
+#define CFG_FLASH_WORD_SIZE unsigned short /* flash word size (width) */
+#define CFG_FLASH_ADDR0 0x5555 /* 1st address for flash config cycles */
+#define CFG_FLASH_ADDR1 0x2AAA /* 2nd address for flash config cycles */
/*
* The following defines are added for buggy IOP480 byte interface.
* All other boards should use the standard values (CPCI405 etc.)
*/
-#define CFG_FLASH_READ0 0x0000 /* 0 is standard */
-#define CFG_FLASH_READ1 0x0001 /* 1 is standard */
-#define CFG_FLASH_READ2 0x0002 /* 2 is standard */
+#define CFG_FLASH_READ0 0x0000 /* 0 is standard */
+#define CFG_FLASH_READ1 0x0001 /* 1 is standard */
+#define CFG_FLASH_READ2 0x0002 /* 2 is standard */
-#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
+#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
#if 0 /* test-only */
-#define CFG_JFFS2_FIRST_BANK 0 /* use for JFFS2 */
-#define CFG_JFFS2_NUM_BANKS 1 /* ! second bank contains U-Boot */
+#define CFG_JFFS2_FIRST_BANK 0 /* use for JFFS2 */
+#define CFG_JFFS2_NUM_BANKS 1 /* ! second bank contains U-Boot */
#endif
/*-----------------------------------------------------------------------
* Environment Variable setup
*/
-#define CFG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
-#define CFG_ENV_OFFSET 0x100 /* environment starts at the beginning of the EEPROM */
-#define CFG_ENV_SIZE 0x700 /* 2048 bytes may be used for env vars*/
+#define CFG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
+#define CFG_ENV_OFFSET 0x100 /* environment starts at the beginning of the EEPROM */
+#define CFG_ENV_SIZE 0x700 /* 2048 bytes may be used for env vars*/
/* total size of a CAT24WC16 is 2048 bytes */
#define CFG_NVRAM_BASE_ADDR 0xF0000500 /* NVRAM base address */
-#define CFG_NVRAM_SIZE 242 /* NVRAM size */
+#define CFG_NVRAM_SIZE 242 /* NVRAM size */
/*-----------------------------------------------------------------------
* I2C EEPROM (CAT24WC16) for environment
@@ -248,20 +248,20 @@
#define CFG_I2C_SLAVE 0x7F
#define CFG_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC08 */
-#define CFG_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
-/* mask of address bits that overflow into the "EEPROM chip address" */
+#define CFG_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
+/* mask of address bits that overflow into the "EEPROM chip address" */
#define CFG_I2C_EEPROM_ADDR_OVERFLOW 0x07
#define CFG_EEPROM_PAGE_WRITE_BITS 4 /* The Catalyst CAT24WC08 has */
/* 16 byte page write mode using*/
- /* last 4 bits of the address */
+ /* last 4 bits of the address */
#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
#define CFG_EEPROM_PAGE_WRITE_ENABLE
/*-----------------------------------------------------------------------
* Cache Configuration
*/
-#define CFG_DCACHE_SIZE 16384 /* For IBM 405 CPUs, older 405 ppc's */
- /* have only 8kB, 16kB is save here */
+#define CFG_DCACHE_SIZE 16384 /* For IBM 405 CPUs, older 405 ppc's */
+ /* have only 8kB, 16kB is save here */
#define CFG_CACHELINE_SIZE 32 /* ... */
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
@@ -279,48 +279,48 @@
* External Bus Controller (EBC) Setup
*/
-/* Memory Bank 0 (Flash Bank 0, NOR-FLASH) initialization */
-#define CFG_EBC_PB0AP 0x92015480
-/*#define CFG_EBC_PB0AP 0x08055880 /XXX* TWT=16,CSN=1,OEN=1,WBN=1,WBF=1,TH=4,SOR=1 */
-#define CFG_EBC_PB0CR 0xFFC5A000 /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
+/* Memory Bank 0 (Flash Bank 0, NOR-FLASH) initialization */
+#define CFG_EBC_PB0AP 0x92015480
+/*#define CFG_EBC_PB0AP 0x08055880 /XXX* TWT=16,CSN=1,OEN=1,WBN=1,WBF=1,TH=4,SOR=1 */
+#define CFG_EBC_PB0CR 0xFFC5A000 /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
-/* Memory Bank 1 (Flash Bank 1, NAND-FLASH) initialization */
-#define CFG_EBC_PB1AP 0x92015480
-#define CFG_EBC_PB1CR 0xF4018000 /* BAS=0xF40,BS=1MB,BU=R/W,BW=8bit */
+/* Memory Bank 1 (Flash Bank 1, NAND-FLASH) initialization */
+#define CFG_EBC_PB1AP 0x92015480
+#define CFG_EBC_PB1CR 0xF4018000 /* BAS=0xF40,BS=1MB,BU=R/W,BW=8bit */
-/* Memory Bank 2 (8 Bit Peripheral: UART) initialization */
+/* Memory Bank 2 (8 Bit Peripheral: UART) initialization */
#if 0
-#define CFG_EBC_PB2AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
-#define CFG_EBC_PB2CR 0xF0018000 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */
+#define CFG_EBC_PB2AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
+#define CFG_EBC_PB2CR 0xF0018000 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */
#else
-#define CFG_EBC_PB2AP 0x92015480
-#define CFG_EBC_PB2CR 0xF0018000 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */
+#define CFG_EBC_PB2AP 0x92015480
+#define CFG_EBC_PB2CR 0xF0018000 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */
#endif
-#define DUART0_BA 0xF0000000 /* DUART Base Address */
-#define DUART1_BA 0xF0000008 /* DUART Base Address */
-#define DUART2_BA 0xF0000010 /* DUART Base Address */
-#define DUART3_BA 0xF0000018 /* DUART Base Address */
-#define CFG_NAND_BASE 0xF4000000
+#define DUART0_BA 0xF0000000 /* DUART Base Address */
+#define DUART1_BA 0xF0000008 /* DUART Base Address */
+#define DUART2_BA 0xF0000010 /* DUART Base Address */
+#define DUART3_BA 0xF0000018 /* DUART Base Address */
+#define CFG_NAND_BASE 0xF4000000
/*-----------------------------------------------------------------------
* FPGA stuff
*/
-#define CFG_FPGA_SPARTAN2 1 /* using Xilinx Spartan 2 now */
-#define CFG_FPGA_MAX_SIZE 128*1024 /* 128kByte is enough for XC2S50E*/
+#define CFG_FPGA_SPARTAN2 1 /* using Xilinx Spartan 2 now */
+#define CFG_FPGA_MAX_SIZE 128*1024 /* 128kByte is enough for XC2S50E*/
/* FPGA program pin configuration */
-#define CFG_FPGA_PRG 0x04000000 /* FPGA program pin (ppc output) */
-#define CFG_FPGA_CLK 0x02000000 /* FPGA clk pin (ppc output) */
-#define CFG_FPGA_DATA 0x01000000 /* FPGA data pin (ppc output) */
-#define CFG_FPGA_INIT 0x00010000 /* FPGA init pin (ppc input) */
-#define CFG_FPGA_DONE 0x00008000 /* FPGA done pin (ppc input) */
+#define CFG_FPGA_PRG 0x04000000 /* FPGA program pin (ppc output) */
+#define CFG_FPGA_CLK 0x02000000 /* FPGA clk pin (ppc output) */
+#define CFG_FPGA_DATA 0x01000000 /* FPGA data pin (ppc output) */
+#define CFG_FPGA_INIT 0x00010000 /* FPGA init pin (ppc input) */
+#define CFG_FPGA_DONE 0x00008000 /* FPGA done pin (ppc input) */
/*-----------------------------------------------------------------------
* Definitions for initial stack pointer and data area (in data cache)
*/
/* use on chip memory ( OCM ) for temperary stack until sdram is tested */
-#define CFG_TEMP_STACK_OCM 1
+#define CFG_TEMP_STACK_OCM 1
/* On Chip Memory location */
#define CFG_OCM_DATA_ADDR 0xF8000000
@@ -330,13 +330,13 @@
#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
/*-----------------------------------------------------------------------
* Definitions for GPIO setup (PPC405EP specific)
*
- * GPIO0[0] - External Bus Controller BLAST output
- * GPIO0[1-9] - Instruction trace outputs -> GPIO
+ * GPIO0[0] - External Bus Controller BLAST output
+ * GPIO0[1-9] - Instruction trace outputs -> GPIO
* GPIO0[10-13] - External Bus Controller CS_1 - CS_4 outputs
* GPIO0[14-16] - External Bus Controller ABUS3-ABUS5 outputs -> GPIO
* GPIO0[17-23] - External Interrupts IRQ0 - IRQ6 inputs
@@ -344,15 +344,15 @@
* GPIO0[28-29] - UART1 data signal input/output
* GPIO0[30-31] - EMAC0 and EMAC1 reject packet inputs
*/
-#define CFG_GPIO0_OSRH 0x40000550
-#define CFG_GPIO0_OSRL 0x00000110
-#define CFG_GPIO0_ISR1H 0x00000000
-#define CFG_GPIO0_ISR1L 0x15555445
-#define CFG_GPIO0_TSRH 0x00000000
-#define CFG_GPIO0_TSRL 0x00000000
-#define CFG_GPIO0_TCR 0xF7FE0014
+#define CFG_GPIO0_OSRH 0x40000550
+#define CFG_GPIO0_OSRL 0x00000110
+#define CFG_GPIO0_ISR1H 0x00000000
+#define CFG_GPIO0_ISR1L 0x15555445
+#define CFG_GPIO0_TSRH 0x00000000
+#define CFG_GPIO0_TSRL 0x00000000
+#define CFG_GPIO0_TCR 0xF7FE0014
-#define CFG_DUART_RST (0x80000000 >> 14)
+#define CFG_DUART_RST (0x80000000 >> 14)
/*
* Internal Definitions
@@ -367,16 +367,16 @@
* This value will be set if iic boot eprom is disabled.
*/
#if 0
-#define PLLMR0_DEFAULT PLLMR0_266_133_66_33
-#define PLLMR1_DEFAULT PLLMR1_266_133_66_33
+#define PLLMR0_DEFAULT PLLMR0_266_133_66_33
+#define PLLMR1_DEFAULT PLLMR1_266_133_66_33
#endif
#if 0
-#define PLLMR0_DEFAULT PLLMR0_200_100_50_33
-#define PLLMR1_DEFAULT PLLMR1_200_100_50_33
+#define PLLMR0_DEFAULT PLLMR0_200_100_50_33
+#define PLLMR1_DEFAULT PLLMR1_200_100_50_33
#endif
#if 1
-#define PLLMR0_DEFAULT PLLMR0_133_66_66_33
-#define PLLMR1_DEFAULT PLLMR1_133_66_66_33
+#define PLLMR0_DEFAULT PLLMR0_133_66_66_33
+#define PLLMR1_DEFAULT PLLMR1_133_66_66_33
#endif
#endif /* __CONFIG_H */
diff --git a/include/configs/IAD210.h b/include/configs/IAD210.h
index 6dedbd7..fd15b85 100644
--- a/include/configs/IAD210.h
+++ b/include/configs/IAD210.h
@@ -66,7 +66,7 @@
#define CONFIG_PREBOOT "echo;echo Type \"run flash_nfs\" to mount root filesystem over NFS;echo"
/* using this define saves us updating another source file */
-#define CONFIG_BOARD_PRE_INIT 1
+#define CONFIG_BOARD_EARLY_INIT_F 1
#undef CONFIG_BOOTARGS
/* #define CONFIG_BOOTCOMMAND \
diff --git a/include/configs/IP860.h b/include/configs/IP860.h
index 6490962..47f69a2 100644
--- a/include/configs/IP860.h
+++ b/include/configs/IP860.h
@@ -1,5 +1,5 @@
/*
- * (C) Copyright 2000
+ * (C) Copyright 2000-2004
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*
* See file CREDITS for list of people who contributed to this
@@ -35,7 +35,7 @@
#define CONFIG_MPC860 1 /* This is a MPC860 CPU */
#define CONFIG_IP860 1 /* ...on a IP860 board */
-#define CONFIG_BOARD_PRE_INIT 1 /* Call board_pre_init */
+#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */
#define CONFIG_BAUDRATE 9600
diff --git a/include/configs/MHPC.h b/include/configs/MHPC.h
index e36341f..f942e95 100644
--- a/include/configs/MHPC.h
+++ b/include/configs/MHPC.h
@@ -18,7 +18,7 @@
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
@@ -39,23 +39,23 @@
* (easy to change)
*/
#define CONFIG_MPC823 1 /* This is a MPC823 CPU */
-#define CONFIG_MHPC 1 /* on a miniHiPerCam */
-#define CONFIG_BOARD_PRE_INIT 1 /* do special hardware init. */
-#define CONFIG_MISC_INIT_R 1
+#define CONFIG_MHPC 1 /* on a miniHiPerCam */
+#define CONFIG_BOARD_EARLY_INIT_F 1 /* do special hardware init. */
+#define CONFIG_MISC_INIT_R 1
#define CONFIG_8xx_GCLK_FREQ MPC8XX_SPEED
#undef CONFIG_8xx_CONS_SMC1
-#define CONFIG_8xx_CONS_SMC2 1 /* Console is on SMC2 */
+#define CONFIG_8xx_CONS_SMC2 1 /* Console is on SMC2 */
#undef CONFIG_8xx_CONS_NONE
#define CONFIG_BAUDRATE 9600
#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */
+#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */
-#define CONFIG_ENV_OVERWRITE 1
-#define CONFIG_ETHADDR 00:00:5b:ee:de:ad
+#define CONFIG_ENV_OVERWRITE 1
+#define CONFIG_ETHADDR 00:00:5b:ee:de:ad
-#undef CONFIG_BOOTARGS
+#undef CONFIG_BOOTARGS
#define CONFIG_BOOTCOMMAND \
"bootp;" \
"setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) " \
@@ -66,12 +66,12 @@
#undef CFG_LOADS_BAUD_CHANGE /* don't allow baudrate change */
#undef CONFIG_WATCHDOG /* watchdog disabled */
-#define CONFIG_RTC_MPC8xx /* use internal RTC of MPC8xx */
+#define CONFIG_RTC_MPC8xx /* use internal RTC of MPC8xx */
-#undef CONFIG_UCODE_PATCH
+#undef CONFIG_UCODE_PATCH
/* enable I2C and select the hardware/software driver */
-#undef CONFIG_HARD_I2C /* I2C with hardware support */
+#undef CONFIG_HARD_I2C /* I2C with hardware support */
#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */
/*
* Software (bit-bang) I2C driver configuration
@@ -84,36 +84,36 @@
#define I2C_TRISTATE (immr->im_cpm.cp_pbdir &= ~PB_SDA)
#define I2C_READ ((immr->im_cpm.cp_pbdat & PB_SDA) != 0)
#define I2C_SDA(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SDA; \
- else immr->im_cpm.cp_pbdat &= ~PB_SDA
+ else immr->im_cpm.cp_pbdat &= ~PB_SDA
#define I2C_SCL(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SCL; \
- else immr->im_cpm.cp_pbdat &= ~PB_SCL
+ else immr->im_cpm.cp_pbdat &= ~PB_SCL
#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */
-#define CFG_I2C_SPEED 50000
-#define CFG_I2C_SLAVE 0xFE
-#define CFG_I2C_EEPROM_ADDR 0x50 /* EEPROM X24C04 */
-#define CFG_I2C_EEPROM_ADDR_LEN 1 /* bytes of address */
-/* mask of address bits that overflow into the "EEPROM chip address" */
-#define CFG_I2C_EEPROM_ADDR_OVERFLOW 0x07
-#define CFG_EEPROM_PAGE_WRITE_BITS 3
-#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10
+#define CFG_I2C_SPEED 50000
+#define CFG_I2C_SLAVE 0xFE
+#define CFG_I2C_EEPROM_ADDR 0x50 /* EEPROM X24C04 */
+#define CFG_I2C_EEPROM_ADDR_LEN 1 /* bytes of address */
+/* mask of address bits that overflow into the "EEPROM chip address" */
+#define CFG_I2C_EEPROM_ADDR_OVERFLOW 0x07
+#define CFG_EEPROM_PAGE_WRITE_BITS 3
+#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10
-#define LCD_VIDEO_ADDR (SDRAM_MAX_SIZE-SDRAM_RES_SIZE)
-#define LCD_VIDEO_SIZE SDRAM_RES_SIZE /* 2MB */
-#define LCD_VIDEO_COLS 640
-#define LCD_VIDEO_ROWS 480
-#define LCD_VIDEO_FG 255
-#define LCD_VIDEO_BG 0
+#define LCD_VIDEO_ADDR (SDRAM_MAX_SIZE-SDRAM_RES_SIZE)
+#define LCD_VIDEO_SIZE SDRAM_RES_SIZE /* 2MB */
+#define LCD_VIDEO_COLS 640
+#define LCD_VIDEO_ROWS 480
+#define LCD_VIDEO_FG 255
+#define LCD_VIDEO_BG 0
-#undef CONFIG_VIDEO /* test only ! s.a devices.c and 8xx */
-#define CONFIG_CFB_CONSOLE /* framebuffer console with std input */
+#undef CONFIG_VIDEO /* test only ! s.a devices.c and 8xx */
+#define CONFIG_CFB_CONSOLE /* framebuffer console with std input */
#define CONFIG_VIDEO_LOGO
-#define VIDEO_KBD_INIT_FCT 0 /* no KBD dev on MHPC - use serial */
-#define VIDEO_TSTC_FCT serial_tstc
-#define VIDEO_GETC_FCT serial_getc
+#define VIDEO_KBD_INIT_FCT 0 /* no KBD dev on MHPC - use serial */
+#define VIDEO_TSTC_FCT serial_tstc
+#define VIDEO_GETC_FCT serial_getc
-#define CONFIG_BR0_WORKAROUND 1
+#define CONFIG_BR0_WORKAROUND 1
#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \
CFG_CMD_DATE | \
@@ -131,23 +131,23 @@
/*
* Miscellaneous configurable options
*/
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+#define CFG_LONGHELP /* undef to save memory */
+#define CFG_PROMPT "=> " /* Monitor Command Prompt */
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-#define CFG_LOAD_ADDR 0x300000 /* default load address */
+#define CFG_LOAD_ADDR 0x300000 /* default load address */
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
@@ -166,33 +166,33 @@
* Definitions for initial stack pointer and data area (in DPRAM)
*/
#define CFG_INIT_RAM_ADDR CFG_IMMR
-#define CFG_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */
-#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */
-#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+#define CFG_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */
+#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */
+#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
/*-----------------------------------------------------------------------
* Start addresses for the final memory configuration
* (Set up by the startup code)
* Please note that CFG_SDRAM_BASE _must_ start at 0
*/
-#define CFG_SDRAM_BASE 0x00000000
+#define CFG_SDRAM_BASE 0x00000000
#define CFG_FLASH_BASE 0xfe000000
-#define CFG_MONITOR_LEN 0x40000 /* Reserve 256 kB for Monitor */
-#undef CFG_MONITOR_BASE /* to run U-Boot from RAM */
+#define CFG_MONITOR_LEN 0x40000 /* Reserve 256 kB for Monitor */
+#undef CFG_MONITOR_BASE /* to run U-Boot from RAM */
#define CFG_MONITOR_BASE CFG_FLASH_BASE
-#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
+#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
-#define CFG_JFFS2_FIRST_BANK 0 /* use for JFFS2 */
-#define CFG_JFFS2_NUM_BANKS 1 /* one flash only */
+#define CFG_JFFS2_FIRST_BANK 0 /* use for JFFS2 */
+#define CFG_JFFS2_NUM_BANKS 1 /* one flash only */
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map- for Linux */
+#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map- for Linux */
/*-----------------------------------------------------------------------
* FLASH organization
@@ -202,9 +202,9 @@
#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
-#define CFG_ENV_IS_IN_FLASH 1
-#define CFG_ENV_OFFSET CFG_MONITOR_LEN /* Offset of Environment */
-#define CFG_ENV_SIZE 0x20000 /* Total Size of Environment */
+#define CFG_ENV_IS_IN_FLASH 1
+#define CFG_ENV_OFFSET CFG_MONITOR_LEN /* Offset of Environment */
+#define CFG_ENV_SIZE 0x20000 /* Total Size of Environment */
/*-----------------------------------------------------------------------
* Cache Configuration
@@ -262,7 +262,7 @@
* interrupt status bit - leave PLL multiplication factor unchanged !
*/
#define MPC8XX_SPEED 50000000L
-#define MPC8XX_XIN 5000000L /* ref clk */
+#define MPC8XX_XIN 5000000L /* ref clk */
#define MPC8XX_FACT (MPC8XX_SPEED/MPC8XX_XIN)
#define CFG_PLPRCR (((MPC8XX_FACT-1) << PLPRCR_MF_SHIFT) | \
PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
@@ -307,8 +307,8 @@
* BR1 and OR1 (SDRAM)
*/
#define SDRAM_BASE1_PRELIM 0x00000000 /* SDRAM bank #0 */
-#define SDRAM_MAX_SIZE 0x01000000 /* max 16 MB */
-#define SDRAM_RES_SIZE 0x00200000 /* 2 MB for framebuffer */
+#define SDRAM_MAX_SIZE 0x01000000 /* max 16 MB */
+#define SDRAM_RES_SIZE 0x00200000 /* 2 MB for framebuffer */
/* SDRAM timing: drive GPL5 high on first cycle */
#define CFG_OR_TIMING_SDRAM (OR_G5LS)
@@ -358,14 +358,14 @@
*-----------------------------------------------------------------------
*
*/
-#define CFG_DER 0
+#define CFG_DER 0
/*
* Internal Definitions
*
* Boot Flags
*/
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
#define BOOTFLAG_WARM 0x02 /* Software reboot */
#endif /* __CONFIG_H */
diff --git a/include/configs/MIP405.h b/include/configs/MIP405.h
index 9c21745..cfe74e1 100644
--- a/include/configs/MIP405.h
+++ b/include/configs/MIP405.h
@@ -252,7 +252,7 @@
/* Size: 0=1MB, 1=2MB, 2=4MB, 3=8MB, 4=16MB, 5=32MB, 6=64MB, 7=128MB */
#define FLASH_SIZE_PRELIM 3 /* maximal flash FLASH size bank #0 */
-#define CONFIG_BOARD_PRE_INIT
+#define CONFIG_BOARD_EARLY_INIT_F 1
/* Peripheral Bus Mapping */
#define PER_PLD_ADDR 0xF4000000 /* smallest window is 1MByte 0x10 0000*/
diff --git a/include/configs/MPC8260ADS.h b/include/configs/MPC8260ADS.h
index 9625cdf..f4ccdaf 100644
--- a/include/configs/MPC8260ADS.h
+++ b/include/configs/MPC8260ADS.h
@@ -51,7 +51,7 @@
#define CONFIG_ADSTYPE CFG_8260ADS
#endif /* CONFIG_ADSTYPE */
-#define CONFIG_BOARD_PRE_INIT 1 /* Call board_pre_init */
+#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
/* allow serial and ethaddr to be overwritten */
#define CONFIG_ENV_OVERWRITE
diff --git a/include/configs/MPC8266ADS.h b/include/configs/MPC8266ADS.h
index 26c1306..c62f942 100644
--- a/include/configs/MPC8266ADS.h
+++ b/include/configs/MPC8266ADS.h
@@ -49,10 +49,10 @@
* (easy to change)
*/
-#define CONFIG_MPC8260 1 /* This is an MPC8260 CPU */
-#define CONFIG_MPC8266ADS 1 /* ...on motorola ads board */
+#define CONFIG_MPC8260 1 /* This is an MPC8260 CPU */
+#define CONFIG_MPC8266ADS 1 /* ...on motorola ADS board */
-#define CONFIG_BOARD_PRE_INIT 1 /* Call board_pre_init */
+#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
/* allow serial and ethaddr to be overwritten */
#define CONFIG_ENV_OVERWRITE
diff --git a/include/configs/MPC8540ADS.h b/include/configs/MPC8540ADS.h
index 951d1fe..2f1bb48 100644
--- a/include/configs/MPC8540ADS.h
+++ b/include/configs/MPC8540ADS.h
@@ -31,21 +31,21 @@
#define __CONFIG_H
/* High Level Configuration Options */
-#define CONFIG_BOOKE 1 /* BOOKE */
+#define CONFIG_BOOKE 1 /* BOOKE */
#define CONFIG_E500 1 /* BOOKE e500 family */
#define CONFIG_MPC85xx 1 /* MPC8540/MPC8560 */
-#define CONFIG_MPC85xx_REV1 1 /* MPC85xx Rev 1 Chip */
-#define CONFIG_MPC8540 1 /* MPC8540 specific */
+#define CONFIG_MPC85xx_REV1 1 /* MPC85xx Rev 1 Chip */
+#define CONFIG_MPC8540 1 /* MPC8540 specific */
#define CONFIG_MPC8540ADS 1 /* MPC8540ADS board specific*/
-#undef CONFIG_PCI /* pci ethernet support */
-#define CONFIG_TSEC_ENET /* tsec ethernet support */
+#undef CONFIG_PCI /* pci ethernet support */
+#define CONFIG_TSEC_ENET /* tsec ethernet support */
#define CONFIG_ENV_OVERWRITE
-#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
-#undef CONFIG_DDR_ECC /* only for ECC DDR module */
+#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
+#undef CONFIG_DDR_ECC /* only for ECC DDR module */
#if defined(CONFIG_MPC85xx_REV1)
-#define CONFIG_DDR_DLL /* possible DLL fix needed */
+#define CONFIG_DDR_DLL /* possible DLL fix needed */
#endif
/* Using Localbus SDRAM to emulate flash before we can program the flash,
@@ -53,24 +53,24 @@
*/
#undef CONFIG_RAM_AS_FLASH
-#if !defined(CONFIG_PCI) /* some PCI card is 33Mhz only */
+#if !defined(CONFIG_PCI) /* some PCI card is 33Mhz only */
#define CONFIG_SYS_CLK_FREQ 66000000 /* sysclk for MPC85xx */
#else
#define CONFIG_SYS_CLK_FREQ 33000000 /* most pci cards are 33Mhz */
#endif
-#if !defined(CONFIG_SPD_EEPROM) /* manually set up DDR parameters */
+#if !defined(CONFIG_SPD_EEPROM) /* manually set up DDR parameters */
#define CONFIG_DDR_SETTING
#endif
/* below can be toggled for performance analysis. otherwise use default */
-#define CONFIG_L2_CACHE /* toggle L2 cache */
-#undef CONFIG_BTB /* toggle branch predition */
-#undef CONFIG_ADDR_STREAMING /* toggle addr streaming */
+#define CONFIG_L2_CACHE /* toggle L2 cache */
+#undef CONFIG_BTB /* toggle branch predition */
+#undef CONFIG_ADDR_STREAMING /* toggle addr streaming */
-#define CONFIG_BOARD_PRE_INIT 1 /* Call board_pre_init */
+#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
-#undef CFG_DRAM_TEST /* memory test, takes time */
+#undef CFG_DRAM_TEST /* memory test, takes time */
#define CFG_MEMTEST_START 0x00200000 /* memtest works on */
#define CFG_MEMTEST_END 0x00400000
@@ -82,13 +82,13 @@
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*/
-#define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
-#define CFG_CCSRBAR 0xfdf00000 /* relocated CCSRBAR */
+#define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
+#define CFG_CCSRBAR 0xfdf00000 /* relocated CCSRBAR */
#define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */
-#define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory */
+#define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory */
#define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE
-#define CFG_SDRAM_SIZE 128 /* DDR is now 128MB */
+#define CFG_SDRAM_SIZE 128 /* DDR is now 128MB */
#if defined(CONFIG_RAM_AS_FLASH)
#define CFG_LBC_SDRAM_BASE 0xfc000000 /* Localbus SDRAM */
@@ -98,44 +98,44 @@
#define CFG_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */
#if defined(CONFIG_RAM_AS_FLASH)
-#define CFG_FLASH_BASE 0xf8000000 /* start of FLASH 16M */
+#define CFG_FLASH_BASE 0xf8000000 /* start of FLASH 16M */
#define CFG_BR0_PRELIM 0xf8001801 /* port size 32bit */
#else /* Boot from real Flash */
-#define CFG_FLASH_BASE 0xff000000 /* start of FLASH 16M */
+#define CFG_FLASH_BASE 0xff000000 /* start of FLASH 16M */
#define CFG_BR0_PRELIM 0xff001801 /* port size 32bit */
#endif
-#define CFG_OR0_PRELIM 0xff006ff7 /* 16MB Flash */
+#define CFG_OR0_PRELIM 0xff006ff7 /* 16MB Flash */
#define CFG_MAX_FLASH_BANKS 1 /* number of banks */
-#define CFG_MAX_FLASH_SECT 64 /* sectors per device */
+#define CFG_MAX_FLASH_SECT 64 /* sectors per device */
#undef CFG_FLASH_CHECKSUM
#define CFG_FLASH_ERASE_TOUT 60000 /* Timeout for Flash Erase (in ms)*/
#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms)*/
-#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */
+#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */
#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
#define CFG_RAMBOOT
#else
-#undef CFG_RAMBOOT
+#undef CFG_RAMBOOT
#endif
#define SPD_EEPROM_ADDRESS 0x51 /* DDR DIMM */
#if defined(CONFIG_DDR_SETTING)
-#define CFG_DDR_CS0_BNDS 0x00000007 /* 0-128MB */
-#define CFG_DDR_CS0_CONFIG 0x80000002
-#define CFG_DDR_TIMING_1 0x37344321
-#define CFG_DDR_TIMING_2 0x00000800 /* P9-45,may need tuning*/
-#define CFG_DDR_CONTROL 0xc2000000 /* unbuffered,no DYN_PWR*/
-#define CFG_DDR_MODE 0x00000062 /* DLL,normal,seq,4/2.5 */
-#define CFG_DDR_INTERVAL 0x05200100 /* autocharge,no open page*/
+#define CFG_DDR_CS0_BNDS 0x00000007 /* 0-128MB */
+#define CFG_DDR_CS0_CONFIG 0x80000002
+#define CFG_DDR_TIMING_1 0x37344321
+#define CFG_DDR_TIMING_2 0x00000800 /* P9-45,may need tuning*/
+#define CFG_DDR_CONTROL 0xc2000000 /* unbuffered,no DYN_PWR*/
+#define CFG_DDR_MODE 0x00000062 /* DLL,normal,seq,4/2.5 */
+#define CFG_DDR_INTERVAL 0x05200100 /* autocharge,no open page*/
#endif
#undef CONFIG_CLOCKS_IN_MHZ
/* local bus definitions */
-#define CFG_BR2_PRELIM 0xf8001861 /* 64MB localbus SDRAM */
+#define CFG_BR2_PRELIM 0xf8001861 /* 64MB localbus SDRAM */
#define CFG_OR2_PRELIM 0xfc006901
#define CFG_LBC_LCRR 0x00030004 /* local bus freq divider*/
#define CFG_LBC_LBCR 0x00000000
@@ -148,52 +148,52 @@
#define CFG_LBC_LSDMR_5 0x4061b723
#if defined(CONFIG_RAM_AS_FLASH)
-#define CFG_BR4_PRELIM 0xf8000801 /* 32KB, 8-bit wide for ADS config reg */
+#define CFG_BR4_PRELIM 0xf8000801 /* 32KB, 8-bit wide for ADS config reg */
#else
-#define CFG_BR4_PRELIM 0xfc000801 /* 32KB, 8-bit wide for ADS config reg */
+#define CFG_BR4_PRELIM 0xfc000801 /* 32KB, 8-bit wide for ADS config reg */
#endif
-#define CFG_OR4_PRELIM 0xffffe1f1
-#define CFG_BCSR (CFG_BR4_PRELIM & 0xffff8000)
+#define CFG_OR4_PRELIM 0xffffe1f1
+#define CFG_BCSR (CFG_BR4_PRELIM & 0xffff8000)
#define CONFIG_L1_INIT_RAM
-#define CFG_INIT_RAM_LOCK 1
-#define CFG_INIT_RAM_ADDR 0x40000000 /* Initial RAM address */
-#define CFG_INIT_RAM_END 0x4000 /* End of used area in RAM */
+#define CFG_INIT_RAM_LOCK 1
+#define CFG_INIT_RAM_ADDR 0x40000000 /* Initial RAM address */
+#define CFG_INIT_RAM_END 0x4000 /* End of used area in RAM */
-#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */
+#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
-#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
-#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
+#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
+#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
/* Serial Port */
#define CONFIG_CONS_INDEX 1
#undef CONFIG_SERIAL_SOFTWARE_FIFO
#define CFG_NS16550
#define CFG_NS16550_SERIAL
-#define CFG_NS16550_REG_SIZE 1
+#define CFG_NS16550_REG_SIZE 1
#define CFG_NS16550_CLK get_bus_freq(0)
-#define CONFIG_BAUDRATE 115200
+#define CONFIG_BAUDRATE 115200
#define CFG_BAUDRATE_TABLE \
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
-#define CFG_NS16550_COM1 (CFG_CCSRBAR+0x4500)
-#define CFG_NS16550_COM2 (CFG_CCSRBAR+0x4600)
+#define CFG_NS16550_COM1 (CFG_CCSRBAR+0x4500)
+#define CFG_NS16550_COM2 (CFG_CCSRBAR+0x4600)
/* Use the HUSH parser */
#define CFG_HUSH_PARSER
-#ifdef CFG_HUSH_PARSER
+#ifdef CFG_HUSH_PARSER
#define CFG_PROMPT_HUSH_PS2 "> "
#endif
/* I2C */
-#define CONFIG_HARD_I2C /* I2C with hardware support*/
+#define CONFIG_HARD_I2C /* I2C with hardware support*/
#undef CONFIG_SOFT_I2C /* I2C bit-banged */
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
#define CFG_I2C_SLAVE 0x7F
-#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */
+#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */
/* General PCI */
#define CFG_PCI_MEM_BASE 0xe0000000
@@ -203,22 +203,22 @@
#define CONFIG_NET_MULTI
#undef CONFIG_EEPRO100
#define CONFIG_TULIP
-#define CONFIG_PCI_PNP /* do pci plug-and-play */
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
#if !defined(CONFIG_PCI_PNP)
- #define PCI_ENET0_IOADDR 0xe0000000
- #define PCI_ENET0_MEMADDR 0xe0000000
- #define PCI_IDSEL_NUMBER 0x0c /*slot0->3(IDSEL)=12->15*/
+ #define PCI_ENET0_IOADDR 0xe0000000
+ #define PCI_ENET0_MEMADDR 0xe0000000
+ #define PCI_IDSEL_NUMBER 0x0c /*slot0->3(IDSEL)=12->15*/
#endif
-#define CONFIG_PCI_SCAN_SHOW 1 /* show pci devices on startup */
-#define CFG_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */
+#define CONFIG_PCI_SCAN_SHOW 1 /* show pci devices on startup */
+#define CFG_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */
#if defined(CONFIG_MPC85xx_REV1) /* Errata PCI 8 */
#define CFG_PCI_SUBSYS_DEVICEID 0x0003
#else
#define CFG_PCI_SUBSYS_DEVICEID 0x0008
#endif
#elif defined(CONFIG_TSEC_ENET)
-#define CONFIG_NET_MULTI 1
-#define CONFIG_PHY_M88E1011 1 /* GigaBit Ether PHY */
+#define CONFIG_NET_MULTI 1
+#define CONFIG_PHY_M88E1011 1 /* GigaBit Ether PHY */
#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_PHY_ADDR 8 /* PHY address */
#endif
@@ -232,7 +232,7 @@
#else
#define CFG_ENV_IS_IN_FLASH 1
#define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000)
- #define CFG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */
+ #define CFG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */
#endif
#define CFG_ENV_SIZE 0x2000
#else
@@ -242,10 +242,10 @@
#define CFG_ENV_SIZE 0x2000
#endif
-#define CONFIG_BOOTARGS "root=/dev/nfs rw nfsroot=163.12.64.52:/localhome/r6aads/linuxppc/target ip=10.82.0.105:163.12.64.52:10.82.1.254:255.255.254.0:mpc8540ads-003:eth0:off console=ttyS0,115200"
+#define CONFIG_BOOTARGS "root=/dev/nfs rw nfsroot=163.12.64.52:/localhome/r6aads/linuxppc/target ip=10.82.0.105:163.12.64.52:10.82.1.254:255.255.254.0:mpc8540ads-003:eth0:off console=ttyS0,115200"
/*#define CONFIG_BOOTARGS "root=/dev/ram rw console=ttyS0,115200"*/
#define CONFIG_BOOTCOMMAND "bootm 0xff300000 0xff700000"
-#define CONFIG_BOOTDELAY 3 /* -1 disable autoboot */
+#define CONFIG_BOOTDELAY 3 /* -1 disable autoboot */
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
@@ -274,7 +274,7 @@
* Miscellaneous configurable options
*/
#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "MPC8540ADS=> " /* Monitor Command Prompt */
+#define CFG_PROMPT "MPC8540ADS=> " /* Monitor Command Prompt */
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
@@ -291,10 +291,10 @@
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
/* Cache Configuration */
-#define CFG_DCACHE_SIZE 32768
+#define CFG_DCACHE_SIZE 32768
#define CFG_CACHELINE_SIZE 32
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
@@ -315,17 +315,17 @@
/* NOTE: change below for your network setting!!! */
#if defined(CONFIG_TSEC_ENET)
-#define CONFIG_ETHADDR 00:01:af:07:9b:8a
-#define CONFIG_ETH1ADDR 00:01:af:07:9b:8b
-#define CONFIG_ETH2ADDR 00:01:af:07:9b:8c
+#define CONFIG_ETHADDR 00:01:af:07:9b:8a
+#define CONFIG_ETH1ADDR 00:01:af:07:9b:8b
+#define CONFIG_ETH2ADDR 00:01:af:07:9b:8c
#endif
-#define CONFIG_SERVERIP 163.12.64.52
-#define CONFIG_IPADDR 10.82.0.105
-#define CONFIG_GATEWAYIP 10.82.1.254
-#define CONFIG_NETMASK 255.255.254.0
-#define CONFIG_HOSTNAME MPC8560ADS_PILOT_003
-#define CONFIG_ROOTPATH /home/r6aads/mpclinux/eldk-2.0.2/ppc_82xx
-#define CONFIG_BOOTFILE pImage
+#define CONFIG_SERVERIP 163.12.64.52
+#define CONFIG_IPADDR 10.82.0.105
+#define CONFIG_GATEWAYIP 10.82.1.254
+#define CONFIG_NETMASK 255.255.254.0
+#define CONFIG_HOSTNAME MPC8560ADS_PILOT_003
+#define CONFIG_ROOTPATH /home/r6aads/mpclinux/eldk-2.0.2/ppc_82xx
+#define CONFIG_BOOTFILE pImage
#endif /* __CONFIG_H */
diff --git a/include/configs/MPC8560ADS.h b/include/configs/MPC8560ADS.h
index 0d844d1..44b128f 100644
--- a/include/configs/MPC8560ADS.h
+++ b/include/configs/MPC8560ADS.h
@@ -31,22 +31,22 @@
#define __CONFIG_H
/* High Level Configuration Options */
-#define CONFIG_BOOKE 1 /* BOOKE */
-#define CONFIG_E500 1 /* BOOKE e500 family */
-#define CONFIG_MPC85xx 1 /* MPC8540/MPC8560 */
-#define CONFIG_MPC85xx_REV1 1 /* MPC85xx Rev 1.0 chip */
-#define CONFIG_MPC8560 1 /* MPC8560 specific */
-#define CONFIG_MPC8560ADS 1 /* MPC8560ADS board specific*/
+#define CONFIG_BOOKE 1 /* BOOKE */
+#define CONFIG_E500 1 /* BOOKE e500 family */
+#define CONFIG_MPC85xx 1 /* MPC8540/MPC8560 */
+#define CONFIG_MPC85xx_REV1 1 /* MPC85xx Rev 1.0 chip */
+#define CONFIG_MPC8560 1 /* MPC8560 specific */
+#define CONFIG_MPC8560ADS 1 /* MPC8560ADS board specific */
-#undef CONFIG_PCI /* pci ethernet support */
-#define CONFIG_TSEC_ENET /* tsec ethernet support*/
-#undef CONFIG_ETHER_ON_FCC /* cpm FCC ethernet support */
+#undef CONFIG_PCI /* pci ethernet support */
+#define CONFIG_TSEC_ENET /* tsec ethernet support */
+#undef CONFIG_ETHER_ON_FCC /* cpm FCC ethernet support */
#define CONFIG_ENV_OVERWRITE
-#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
-#undef CONFIG_DDR_ECC /* only for ECC DDR module */
+#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
+#undef CONFIG_DDR_ECC /* only for ECC DDR module */
#if defined(CONFIG_MPC85xx_REV1)
-#define CONFIG_DDR_DLL /* possible DLL fix needed */
+#define CONFIG_DDR_DLL /* possible DLL fix needed */
#endif
/* Using Localbus SDRAM to emulate flash before we can program the flash,
@@ -54,10 +54,10 @@
*/
#undef CONFIG_RAM_AS_FLASH
-#if !defined(CONFIG_PCI) /* some PCI card is 33Mhz only */
-#define CONFIG_SYS_CLK_FREQ 66000000/* sysclk for MPC85xx */
+#if !defined(CONFIG_PCI) /* some PCI card is 33Mhz only */
+#define CONFIG_SYS_CLK_FREQ 66000000/* sysclk for MPC85xx */
#else
-#define CONFIG_SYS_CLK_FREQ 33000000/* most pci cards are 33Mhz */
+#define CONFIG_SYS_CLK_FREQ 33000000/* most pci cards are 33Mhz */
#endif
#if !defined(CONFIG_SPD_EEPROM) /* manually set up DDR parameters */
@@ -65,15 +65,15 @@
#endif
/* below can be toggled for performance analysis. otherwise use default */
-#define CONFIG_L2_CACHE /* toggle L2 cache */
-#undef CONFIG_BTB /* toggle branch predition */
-#undef CONFIG_ADDR_STREAMING /* toggle addr streaming */
+#define CONFIG_L2_CACHE /* toggle L2 cache */
+#undef CONFIG_BTB /* toggle branch predition */
+#undef CONFIG_ADDR_STREAMING /* toggle addr streaming */
-#define CONFIG_BOARD_PRE_INIT 1 /* Call board_pre_init */
+#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
-#undef CFG_DRAM_TEST /* memory test, takes time */
-#define CFG_MEMTEST_START 0x00200000 /* memtest region */
-#define CFG_MEMTEST_END 0x00400000
+#undef CFG_DRAM_TEST /* memory test, takes time */
+#define CFG_MEMTEST_START 0x00200000 /* memtest region */
+#define CFG_MEMTEST_END 0x00400000
#if (defined(CONFIG_PCI) && defined(CONFIG_TSEC_ENET) || \
defined(CONFIG_PCI) && defined(CONFIG_ETHER_ON_FCC) || \
@@ -85,48 +85,48 @@
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*/
-#define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
-#define CFG_CCSRBAR 0xfdf00000 /* relocated CCSRBAR */
+#define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
+#define CFG_CCSRBAR 0xfdf00000 /* relocated CCSRBAR */
#define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */
-#define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory */
+#define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory */
#define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE
-#define CFG_SDRAM_SIZE 128 /* DDR is 128MB */
+#define CFG_SDRAM_SIZE 128 /* DDR is 128MB */
#if defined(CONFIG_RAM_AS_FLASH)
-#define CFG_LBC_SDRAM_BASE 0xfc000000 /* Localbus SDRAM */
+#define CFG_LBC_SDRAM_BASE 0xfc000000 /* Localbus SDRAM */
#else
-#define CFG_LBC_SDRAM_BASE 0xf8000000 /* Localbus SDRAM */
+#define CFG_LBC_SDRAM_BASE 0xf8000000 /* Localbus SDRAM */
#endif
#define CFG_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */
#if defined(CONFIG_RAM_AS_FLASH)
-#define CFG_FLASH_BASE 0xf8000000 /* start of FLASH 16M */
-#define CFG_BR0_PRELIM 0xf8001801 /* port size 32bit */
+#define CFG_FLASH_BASE 0xf8000000 /* start of FLASH 16M */
+#define CFG_BR0_PRELIM 0xf8001801 /* port size 32bit */
#else /* Boot from real Flash */
-#define CFG_FLASH_BASE 0xff000000 /* start of FLASH 16M */
-#define CFG_BR0_PRELIM 0xff001801 /* port size 32bit */
+#define CFG_FLASH_BASE 0xff000000 /* start of FLASH 16M */
+#define CFG_BR0_PRELIM 0xff001801 /* port size 32bit */
#endif
-#define CFG_OR0_PRELIM 0xff006ff7 /* 16MB Flash */
+#define CFG_OR0_PRELIM 0xff006ff7 /* 16MB Flash */
#define CFG_MAX_FLASH_BANKS 1 /* number of banks */
-#define CFG_MAX_FLASH_SECT 64 /* sectors per device */
+#define CFG_MAX_FLASH_SECT 64 /* sectors per device */
#undef CFG_FLASH_CHECKSUM
#define CFG_FLASH_ERASE_TOUT 60000 /* Timeout for Flash Erase (in ms) */
#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
-#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */
+#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */
#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
#define CFG_RAMBOOT
#else
-#undef CFG_RAMBOOT
+#undef CFG_RAMBOOT
#endif
-#define SPD_EEPROM_ADDRESS 0x51 /* DDR DIMM */
+#define SPD_EEPROM_ADDRESS 0x51 /* DDR DIMM */
#if defined(CONFIG_DDR_SETTING)
-#define CFG_DDR_CS0_BNDS 0x00000007 /* 0-128MB */
+#define CFG_DDR_CS0_BNDS 0x00000007 /* 0-128MB */
#define CFG_DDR_CS0_CONFIG 0x80000002
#define CFG_DDR_TIMING_1 0x37344321
#define CFG_DDR_TIMING_2 0x00000800 /* P9-45,may need tuning*/
@@ -138,9 +138,9 @@
#undef CONFIG_CLOCKS_IN_MHZ
/* local bus definitions */
-#define CFG_BR2_PRELIM 0xf8001861 /* 64MB localbus SDRAM */
+#define CFG_BR2_PRELIM 0xf8001861 /* 64MB localbus SDRAM */
#define CFG_OR2_PRELIM 0xfc006901
-#define CFG_LBC_LCRR 0x00030004 /* local bus freq */
+#define CFG_LBC_LCRR 0x00030004 /* local bus freq */
#define CFG_LBC_LBCR 0x00000000
#define CFG_LBC_LSRT 0x20000000
#define CFG_LBC_MRTPR 0x20000000
@@ -151,78 +151,78 @@
#define CFG_LBC_LSDMR_5 0x4061b723
#if defined(CONFIG_RAM_AS_FLASH)
-#define CFG_BR4_PRELIM 0xf8000801 /* 32KB, 8-bit wide for ADS config reg */
+#define CFG_BR4_PRELIM 0xf8000801 /* 32KB, 8-bit wide for ADS config reg */
#else
-#define CFG_BR4_PRELIM 0xfc000801 /* 32KB, 8-bit wide for ADS config reg */
+#define CFG_BR4_PRELIM 0xfc000801 /* 32KB, 8-bit wide for ADS config reg */
#endif
#define CFG_OR4_PRELIM 0xffffe1f1
#define CFG_BCSR (CFG_BR4_PRELIM & 0xffff8000)
#define CONFIG_L1_INIT_RAM
-#define CFG_INIT_RAM_LOCK 1
-#define CFG_INIT_RAM_ADDR 0x40000000 /* Initial RAM address */
-#define CFG_INIT_RAM_END 0x4000 /* End of used area in RAM */
+#define CFG_INIT_RAM_LOCK 1
+#define CFG_INIT_RAM_ADDR 0x40000000 /* Initial RAM address */
+#define CFG_INIT_RAM_END 0x4000 /* End of used area in RAM */
-#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */
+#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
-#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
-#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
+#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
+#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
/* Serial Port */
-#define CONFIG_CONS_ON_SCC /* define if console on SCC */
-#undef CONFIG_CONS_NONE /* define if console on something else */
-#define CONFIG_CONS_INDEX 1 /* which serial channel for console */
+#define CONFIG_CONS_ON_SCC /* define if console on SCC */
+#undef CONFIG_CONS_NONE /* define if console on something else */
+#define CONFIG_CONS_INDEX 1 /* which serial channel for console */
-#define CONFIG_BAUDRATE 115200
+#define CONFIG_BAUDRATE 115200
#define CFG_BAUDRATE_TABLE \
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
/* Use the HUSH parser */
#define CFG_HUSH_PARSER
-#ifdef CFG_HUSH_PARSER
+#ifdef CFG_HUSH_PARSER
#define CFG_PROMPT_HUSH_PS2 "> "
#endif
/* I2C */
-#define CONFIG_HARD_I2C /* I2C with hardware support*/
+#define CONFIG_HARD_I2C /* I2C with hardware support*/
#undef CONFIG_SOFT_I2C /* I2C bit-banged */
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
#define CFG_I2C_SLAVE 0x7F
-#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */
+#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */
#define CFG_PCI_MEM_BASE 0xe0000000
#define CFG_PCI_MEM_PHYS 0xe0000000
#define CFG_PCI_MEM_SIZE 0x10000000
-#if defined(CONFIG_PCI) /* PCI Ethernet card */
+#if defined(CONFIG_PCI) /* PCI Ethernet card */
#define CONFIG_NET_MULTI
#define CONFIG_EEPRO100
#undef CONFIG_TULIP
-#define CONFIG_PCI_PNP /* do pci plug-and-play */
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
#if !defined(CONFIG_PCI_PNP)
- #define PCI_ENET0_IOADDR 0xe0000000
- #define PCI_ENET0_MEMADDR 0xe0000000
- #define PCI_IDSEL_NUMBER 0x0c /* slot0->3(IDSEL)=12->15 */
+ #define PCI_ENET0_IOADDR 0xe0000000
+ #define PCI_ENET0_MEMADDR 0xe0000000
+ #define PCI_IDSEL_NUMBER 0x0c /* slot0->3(IDSEL)=12->15 */
#endif
-#define CONFIG_PCI_SCAN_SHOW 1 /* show pci devices on startup */
-#define CFG_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */
-#if defined(CONFIG_MPC85xx_REV1) /* Errata PCI 7 */
+#define CONFIG_PCI_SCAN_SHOW 1 /* show pci devices on startup */
+#define CFG_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */
+#if defined(CONFIG_MPC85xx_REV1) /* Errata PCI 7 */
#define CFG_PCI_SUBSYS_DEVICEID 0x0003
#else
#define CFG_PCI_SUBSYS_DEVICEID 0x0009
#endif
-#elif defined(CONFIG_TSEC_ENET) /* TSEC Ethernet port */
-#define CONFIG_NET_MULTI 1
-#define CONFIG_PHY_M88E1011 1 /* GigaBit Ether PHY */
+#elif defined(CONFIG_TSEC_ENET) /* TSEC Ethernet port */
+#define CONFIG_NET_MULTI 1
+#define CONFIG_PHY_M88E1011 1 /* GigaBit Ether PHY */
#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_PHY_ADDR 8 /* PHY address */
#elif defined(CONFIG_ETHER_ON_FCC) /* CPM FCC Ethernet */
-#define CONFIG_ETHER_ON_FCC /* define if ether on FCC */
-#undef CONFIG_ETHER_NONE /* define if ether on something else */
-#define CONFIG_ETHER_INDEX 2 /* which channel for ether */
+#define CONFIG_ETHER_ON_FCC /* define if ether on FCC */
+#undef CONFIG_ETHER_NONE /* define if ether on something else */
+#define CONFIG_ETHER_INDEX 2 /* which channel for ether */
#if (CONFIG_ETHER_INDEX == 2)
/*
* - Rx-CLK is CLK13
@@ -230,15 +230,15 @@
* - Select bus for bd/buffers
* - Full duplex
*/
- #define CFG_CMXFCR_MASK (CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK)
- #define CFG_CMXFCR_VALUE (CMXFCR_RF2CS_CLK13 | CMXFCR_TF2CS_CLK14)
- #define CFG_CPMFCR_RAMTYPE 0
- #define CFG_FCC_PSMR (FCC_PSMR_FDE)
+ #define CFG_CMXFCR_MASK (CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK)
+ #define CFG_CMXFCR_VALUE (CMXFCR_RF2CS_CLK13 | CMXFCR_TF2CS_CLK14)
+ #define CFG_CPMFCR_RAMTYPE 0
+ #define CFG_FCC_PSMR (FCC_PSMR_FDE)
#define FETH2_RST 0x01
#elif (CONFIG_ETHER_INDEX == 3)
/* need more definitions here for FE3 */
#define FETH3_RST 0x80
- #endif /* CONFIG_ETHER_INDEX */
+ #endif /* CONFIG_ETHER_INDEX */
#define CONFIG_MII /* MII PHY management */
#define CONFIG_BITBANGMII /* bit-bang MII PHY management */
/*
@@ -267,7 +267,7 @@
#else
#define CFG_ENV_IS_IN_FLASH 1
#define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000)
- #define CFG_ENV_SECT_SIZE 0x40000 /* 128K(one sector) for env */
+ #define CFG_ENV_SECT_SIZE 0x40000 /* 128K(one sector) for env */
#endif
#define CFG_ENV_SIZE 0x2000
#else
@@ -320,7 +320,7 @@
* Miscellaneous configurable options
*/
#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "MPC8560ADS=> " /* Monitor Command Prompt */
+#define CFG_PROMPT "MPC8560ADS=> " /* Monitor Command Prompt */
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
@@ -361,17 +361,17 @@
/*Note: change below for your network setting!!! */
#if defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC)
-#define CONFIG_ETHADDR 00:01:af:07:9b:8a
-#define CONFIG_ETH1ADDR 00:01:af:07:9b:8b
-#define CONFIG_ETH2ADDR 00:01:af:07:9b:8c
+#define CONFIG_ETHADDR 00:01:af:07:9b:8a
+#define CONFIG_ETH1ADDR 00:01:af:07:9b:8b
+#define CONFIG_ETH2ADDR 00:01:af:07:9b:8c
#endif
-#define CONFIG_SERVERIP 163.12.64.52
-#define CONFIG_IPADDR 10.82.0.105
+#define CONFIG_SERVERIP 163.12.64.52
+#define CONFIG_IPADDR 10.82.0.105
#define CONFIG_GATEWAYIP 10.82.1.254
#define CONFIG_NETMASK 255.255.254.0
-#define CONFIG_HOSTNAME MPC8560ADS_PILOT_003
-#define CONFIG_ROOTPATH /home/r6aads/mpclinux/eldk-2.0.2/ppc_82xx
-#define CONFIG_BOOTFILE pImage
+#define CONFIG_HOSTNAME MPC8560ADS_PILOT_003
+#define CONFIG_ROOTPATH /home/r6aads/mpclinux/eldk-2.0.2/ppc_82xx
+#define CONFIG_BOOTFILE pImage
#endif /* __CONFIG_H */
diff --git a/include/configs/NETVIA.h b/include/configs/NETVIA.h
index 8221a19..46505b6 100644
--- a/include/configs/NETVIA.h
+++ b/include/configs/NETVIA.h
@@ -105,7 +105,7 @@
#define CONFIG_COMMANDS CONFIG_COMMANDS_BASE
#endif
-#define CONFIG_BOARD_PRE_INIT
+#define CONFIG_BOARD_EARLY_INIT_F 1
#define CONFIG_MISC_INIT_R
/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
diff --git a/include/configs/OCRTC.h b/include/configs/OCRTC.h
index 698b89c..c88d882 100644
--- a/include/configs/OCRTC.h
+++ b/include/configs/OCRTC.h
@@ -34,12 +34,12 @@
*/
#define CONFIG_405GP 1 /* This is a PPC405 CPU */
-#define CONFIG_4xx 1 /* ...member of PPC4xx family */
-#define CONFIG_OCRTC 1 /* ...on a OCRTC board */
+#define CONFIG_4xx 1 /* ...member of PPC4xx family */
+#define CONFIG_OCRTC 1 /* ...on a OCRTC board */
-#define CONFIG_BOARD_PRE_INIT 1 /* call board_pre_init() */
+#define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */
-#define CONFIG_SYS_CLK_FREQ 33000000 /* external frequency to pll */
+#define CONFIG_SYS_CLK_FREQ 33000000 /* external frequency to pll */
#define CONFIG_BAUDRATE 9600
#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */
@@ -51,7 +51,7 @@
#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
#define CONFIG_MII 1 /* MII PHY management */
-#define CONFIG_PHY_ADDR 0 /* PHY address */
+#define CONFIG_PHY_ADDR 0 /* PHY address */
#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \
CFG_CMD_PCI | \
@@ -59,7 +59,7 @@
CFG_CMD_ASKENV | \
CFG_CMD_ELF | \
CFG_CMD_BSP | \
- CFG_CMD_EEPROM )
+ CFG_CMD_EEPROM )
#define CONFIG_MAC_PARTITION
#define CONFIG_DOS_PARTITION
@@ -67,9 +67,9 @@
/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
#include <cmd_confdefs.h>
-#undef CONFIG_WATCHDOG /* watchdog disabled */
+#undef CONFIG_WATCHDOG /* watchdog disabled */
-#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */
+#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */
/*
* Miscellaneous configurable options
@@ -77,32 +77,32 @@
#define CFG_LONGHELP /* undef to save memory */
#define CFG_PROMPT "=> " /* Monitor Command Prompt */
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
#endif
#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
#define CFG_MAXARGS 16 /* max number of command args */
#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
+#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-#undef CFG_EXT_SERIAL_CLOCK /* no external serial clock used */
-#define CFG_IGNORE_405_UART_ERRATA_59 /* ignore ppc405gp errata #59 */
-#define CFG_BASE_BAUD 691200
+#undef CFG_EXT_SERIAL_CLOCK /* no external serial clock used */
+#define CFG_IGNORE_405_UART_ERRATA_59 /* ignore ppc405gp errata #59 */
+#define CFG_BASE_BAUD 691200
/* The following table includes the supported baudrates */
-#define CFG_BAUDRATE_TABLE \
+#define CFG_BAUDRATE_TABLE \
{ 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \
57600, 115200, 230400, 460800, 921600 }
#define CFG_LOAD_ADDR 0x100000 /* default load address */
#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
@@ -110,28 +110,28 @@
* PCI stuff
*-----------------------------------------------------------------------
*/
-#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */
-#define PCI_HOST_FORCE 1 /* configure as pci host */
-#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
+#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */
+#define PCI_HOST_FORCE 1 /* configure as pci host */
+#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
-#define CONFIG_PCI /* include pci support */
-#define CONFIG_PCI_HOST PCI_HOST_AUTO /* select pci host function */
-#define CONFIG_PCI_PNP /* do pci plug-and-play */
- /* resource configuration */
+#define CONFIG_PCI /* include pci support */
+#define CONFIG_PCI_HOST PCI_HOST_AUTO /* select pci host function */
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
+ /* resource configuration */
-#define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */
+#define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */
-#define CONFIG_PCI_BOOTDELAY 0 /* enable pci bootdelay variable*/
+#define CONFIG_PCI_BOOTDELAY 0 /* enable pci bootdelay variable*/
-#define CFG_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */
-#define CFG_PCI_SUBSYS_DEVICEID 0x0410 /* PCI Device ID: OCRTC */
-#define CFG_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/
-#define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */
-#define CFG_PCI_PTM1MS 0xfc000001 /* 64MB, enable hard-wired to 1 */
-#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
-#define CFG_PCI_PTM2LA 0xffc00000 /* point to flash */
-#define CFG_PCI_PTM2MS 0xffc00001 /* 4MB, enable */
-#define CFG_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */
+#define CFG_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */
+#define CFG_PCI_SUBSYS_DEVICEID 0x0410 /* PCI Device ID: OCRTC */
+#define CFG_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/
+#define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */
+#define CFG_PCI_PTM1MS 0xfc000001 /* 64MB, enable hard-wired to 1 */
+#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
+#define CFG_PCI_PTM2LA 0xffc00000 /* point to flash */
+#define CFG_PCI_PTM2MS 0xffc00001 /* 4MB, enable */
+#define CFG_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */
/*-----------------------------------------------------------------------
* Start addresses for the final memory configuration
@@ -159,18 +159,18 @@
#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
-#define CFG_FLASH_WORD_SIZE unsigned short /* flash word size (width) */
-#define CFG_FLASH_ADDR0 0x5555 /* 1st address for flash config cycles */
-#define CFG_FLASH_ADDR1 0x2AAA /* 2nd address for flash config cycles */
+#define CFG_FLASH_WORD_SIZE unsigned short /* flash word size (width) */
+#define CFG_FLASH_ADDR0 0x5555 /* 1st address for flash config cycles */
+#define CFG_FLASH_ADDR1 0x2AAA /* 2nd address for flash config cycles */
/*
* The following defines are added for buggy IOP480 byte interface.
* All other boards should use the standard values (CPCI405 etc.)
*/
-#define CFG_FLASH_READ0 0x0000 /* 0 is standard */
-#define CFG_FLASH_READ1 0x0001 /* 1 is standard */
-#define CFG_FLASH_READ2 0x0002 /* 2 is standard */
+#define CFG_FLASH_READ0 0x0000 /* 0 is standard */
+#define CFG_FLASH_READ1 0x0001 /* 1 is standard */
+#define CFG_FLASH_READ2 0x0002 /* 2 is standard */
-#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
+#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
#if 0 /* Use NVRAM for environment variables */
/*-----------------------------------------------------------------------
@@ -186,9 +186,9 @@
#else /* Use EEPROM for environment variables */
-#define CFG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
-#define CFG_ENV_OFFSET 0x000 /* environment starts at the beginning of the EEPROM */
-#define CFG_ENV_SIZE 0x300 /* 768 bytes may be used for env vars */
+#define CFG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
+#define CFG_ENV_OFFSET 0x000 /* environment starts at the beginning of the EEPROM */
+#define CFG_ENV_SIZE 0x300 /* 768 bytes may be used for env vars */
/* total size of a CAT24WC08 is 1024 bytes */
#endif
@@ -200,12 +200,12 @@
#define CFG_I2C_SLAVE 0x7F
#define CFG_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC08 */
-#define CFG_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
-/* mask of address bits that overflow into the "EEPROM chip address" */
+#define CFG_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
+/* mask of address bits that overflow into the "EEPROM chip address" */
#define CFG_I2C_EEPROM_ADDR_OVERFLOW 0x07
#define CFG_EEPROM_PAGE_WRITE_BITS 4 /* The Catalyst CAT24WC08 has */
/* 16 byte page write mode using*/
- /* last 4 bits of the address */
+ /* last 4 bits of the address */
#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
#define CFG_EEPROM_PAGE_WRITE_ENABLE
@@ -231,53 +231,53 @@
* External Bus Controller (EBC) Setup
*/
-/* Memory Bank 0 (Flash Bank 0) initialization */
-#define CFG_EBC_PB0AP 0x92015480
-#define CFG_EBC_PB0CR 0xFFC5A000 /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
+/* Memory Bank 0 (Flash Bank 0) initialization */
+#define CFG_EBC_PB0AP 0x92015480
+#define CFG_EBC_PB0CR 0xFFC5A000 /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
-/* Memory Bank 1 (Flash Bank 1) initialization */
-#define CFG_EBC_PB1AP 0x92015480
-#define CFG_EBC_PB1CR 0xFF85A000 /* BAS=0xFF8,BS=4MB,BU=R/W,BW=16bit */
+/* Memory Bank 1 (Flash Bank 1) initialization */
+#define CFG_EBC_PB1AP 0x92015480
+#define CFG_EBC_PB1CR 0xFF85A000 /* BAS=0xFF8,BS=4MB,BU=R/W,BW=16bit */
-/* Memory Bank 2 (PLD - FPGA-boot) initialization */
-#define CFG_EBC_PB2AP 0x02015480 /* BME=0x0,TWT=0x04,CSN=0x0,OEN=0x1 */
+/* Memory Bank 2 (PLD - FPGA-boot) initialization */
+#define CFG_EBC_PB2AP 0x02015480 /* BME=0x0,TWT=0x04,CSN=0x0,OEN=0x1 */
/* WBN=0x1,WBF=0x1,TH=0x2,RE=0x0,SOR=0x1,BEM=0x0,PEN=0x0*/
-#define CFG_EBC_PB2CR 0xF0018000 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */
+#define CFG_EBC_PB2CR 0xF0018000 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */
-/* Memory Bank 3 (PLD - OSL) initialization */
-#define CFG_EBC_PB3AP 0x02015480 /* BME=0x0,TWT=0x04,CSN=0x0,OEN=0x1 */
+/* Memory Bank 3 (PLD - OSL) initialization */
+#define CFG_EBC_PB3AP 0x02015480 /* BME=0x0,TWT=0x04,CSN=0x0,OEN=0x1 */
/* WBN=0x1,WBF=0x1,TH=0x2,RE=0x0,SOR=0x1,BEM=0x0,PEN=0x0*/
-#define CFG_EBC_PB3CR 0xF0118000 /* BAS=0xF01,BS=1MB,BU=R/W,BW=8bit */
+#define CFG_EBC_PB3CR 0xF0118000 /* BAS=0xF01,BS=1MB,BU=R/W,BW=8bit */
-/* Memory Bank 4 (Spartan2 1) initialization */
-#define CFG_EBC_PB4AP 0x02015580 /* BME=0x0,TWT=0x04,CSN=0x0,OEN=0x1 */
+/* Memory Bank 4 (Spartan2 1) initialization */
+#define CFG_EBC_PB4AP 0x02015580 /* BME=0x0,TWT=0x04,CSN=0x0,OEN=0x1 */
/* WBN=0x1,WBF=0x1,TH=0x2,RE=0x1,SOR=0x1,BEM=0x0,PEN=0x0*/
-#define CFG_EBC_PB4CR 0xF209C000 /* BAS=0xF20,BS=16MB,BU=R/W,BW=32bit*/
+#define CFG_EBC_PB4CR 0xF209C000 /* BAS=0xF20,BS=16MB,BU=R/W,BW=32bit*/
-/* Memory Bank 5 (Spartan2 2) initialization */
-#define CFG_EBC_PB5AP 0x02015580 /* BME=0x0,TWT=0x04,CSN=0x0,OEN=0x1 */
+/* Memory Bank 5 (Spartan2 2) initialization */
+#define CFG_EBC_PB5AP 0x02015580 /* BME=0x0,TWT=0x04,CSN=0x0,OEN=0x1 */
/* WBN=0x1,WBF=0x1,TH=0x2,RE=0x1,SOR=0x1,BEM=0x0,PEN=0x0*/
-#define CFG_EBC_PB5CR 0xF309C000 /* BAS=0xF30,BS=16MB,BU=R/W,BW=32bit*/
+#define CFG_EBC_PB5CR 0xF309C000 /* BAS=0xF30,BS=16MB,BU=R/W,BW=32bit*/
-/* Memory Bank 6 (Virtex 1) initialization */
-#define CFG_EBC_PB6AP 0x02015580 /* BME=0x0,TWT=0x04,CSN=0x0,OEN=0x1 */
+/* Memory Bank 6 (Virtex 1) initialization */
+#define CFG_EBC_PB6AP 0x02015580 /* BME=0x0,TWT=0x04,CSN=0x0,OEN=0x1 */
/* WBN=0x1,WBF=0x1,TH=0x2,RE=0x1,SOR=0x1,BEM=0x0,PEN=0x0*/
-#define CFG_EBC_PB6CR 0xF409A000 /* BAS=0xF40,BS=16MB,BU=R/W,BW=16bit*/
+#define CFG_EBC_PB6CR 0xF409A000 /* BAS=0xF40,BS=16MB,BU=R/W,BW=16bit*/
-/* Memory Bank 7 (Virtex 2) initialization */
-#define CFG_EBC_PB7AP 0x02015580 /* BME=0x0,TWT=0x04,CSN=0x0,OEN=0x1 */
+/* Memory Bank 7 (Virtex 2) initialization */
+#define CFG_EBC_PB7AP 0x02015580 /* BME=0x0,TWT=0x04,CSN=0x0,OEN=0x1 */
/* WBN=0x1,WBF=0x1,TH=0x2,RE=0x1,SOR=0x1,BEM=0x0,PEN=0x0*/
-#define CFG_EBC_PB7CR 0xF509A000 /* BAS=0xF50,BS=16MB,BU=R/W,BW=16bit*/
+#define CFG_EBC_PB7CR 0xF509A000 /* BAS=0xF50,BS=16MB,BU=R/W,BW=16bit*/
-#define CFG_ETHERNET_MAC_ADDR 0x00000000 /* Pass Ethernet MAC to VxWorks */
+#define CFG_ETHERNET_MAC_ADDR 0x00000000 /* Pass Ethernet MAC to VxWorks */
/*-----------------------------------------------------------------------
* Definitions for initial stack pointer and data area (in DPRAM)
*/
/* use on chip memory ( OCM ) for temperary stack until sdram is tested */
-#define CFG_TEMP_STACK_OCM 1
+#define CFG_TEMP_STACK_OCM 1
/* On Chip Memory location */
#define CFG_OCM_DATA_ADDR 0xF8000000
@@ -287,7 +287,7 @@
#define CFG_INIT_RAM_END CFG_OCM_DATA_SIZE /* End of used area in RAM */
#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
/*
diff --git a/include/configs/ORSG.h b/include/configs/ORSG.h
index cb4c5ee..3dcb514 100644
--- a/include/configs/ORSG.h
+++ b/include/configs/ORSG.h
@@ -34,12 +34,12 @@
*/
#define CONFIG_405GP 1 /* This is a PPC405 CPU */
-#define CONFIG_4xx 1 /* ...member of PPC4xx family */
-#define CONFIG_ORSG 1 /* ...on a ORSG board */
+#define CONFIG_4xx 1 /* ...member of PPC4xx family */
+#define CONFIG_ORSG 1 /* ...on a ORSG board */
-#define CONFIG_BOARD_PRE_INIT 1 /* call board_pre_init() */
+#define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */
-#define CONFIG_SYS_CLK_FREQ 33000000 /* external frequency to pll */
+#define CONFIG_SYS_CLK_FREQ 33000000 /* external frequency to pll */
#define CONFIG_BAUDRATE 9600
#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */
@@ -51,7 +51,7 @@
#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
#define CONFIG_MII 1 /* MII PHY management */
-#define CONFIG_PHY_ADDR 0 /* PHY address */
+#define CONFIG_PHY_ADDR 0 /* PHY address */
#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \
CFG_CMD_PCI | \
@@ -59,7 +59,7 @@
CFG_CMD_ASKENV | \
CFG_CMD_ELF | \
CFG_CMD_BSP | \
- CFG_CMD_EEPROM )
+ CFG_CMD_EEPROM )
#define CONFIG_MAC_PARTITION
#define CONFIG_DOS_PARTITION
@@ -67,9 +67,9 @@
/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
#include <cmd_confdefs.h>
-#undef CONFIG_WATCHDOG /* watchdog disabled */
+#undef CONFIG_WATCHDOG /* watchdog disabled */
-#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */
+#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */
/*
* Miscellaneous configurable options
@@ -77,32 +77,32 @@
#define CFG_LONGHELP /* undef to save memory */
#define CFG_PROMPT "=> " /* Monitor Command Prompt */
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
#endif
#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
#define CFG_MAXARGS 16 /* max number of command args */
#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
+#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-#undef CFG_EXT_SERIAL_CLOCK /* no external serial clock used */
-#define CFG_IGNORE_405_UART_ERRATA_59 /* ignore ppc405gp errata #59 */
-#define CFG_BASE_BAUD 691200
+#undef CFG_EXT_SERIAL_CLOCK /* no external serial clock used */
+#define CFG_IGNORE_405_UART_ERRATA_59 /* ignore ppc405gp errata #59 */
+#define CFG_BASE_BAUD 691200
/* The following table includes the supported baudrates */
-#define CFG_BAUDRATE_TABLE \
+#define CFG_BAUDRATE_TABLE \
{ 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \
57600, 115200, 230400, 460800, 921600 }
#define CFG_LOAD_ADDR 0x100000 /* default load address */
#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
@@ -110,26 +110,26 @@
* PCI stuff
*-----------------------------------------------------------------------
*/
-#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */
-#define PCI_HOST_FORCE 1 /* configure as pci host */
-#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
+#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */
+#define PCI_HOST_FORCE 1 /* configure as pci host */
+#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
-#define CONFIG_PCI /* include pci support */
-#define CONFIG_PCI_HOST PCI_HOST_ADAPTER /* select pci adapter */
-#undef CONFIG_PCI_PNP /* no pci plug-and-play */
- /* resource configuration */
+#define CONFIG_PCI /* include pci support */
+#define CONFIG_PCI_HOST PCI_HOST_ADAPTER /* select pci adapter */
+#undef CONFIG_PCI_PNP /* no pci plug-and-play */
+ /* resource configuration */
-#undef CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */
+#undef CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */
-#define CFG_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */
-#define CFG_PCI_SUBSYS_DEVICEID 0x0411 /* PCI Device ID: ORSG */
-#define CFG_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/
-#define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */
-#define CFG_PCI_PTM1MS 0xfc000001 /* 64MB, enable hard-wired to 1 */
-#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
-#define CFG_PCI_PTM2LA 0xffc00000 /* point to flash */
-#define CFG_PCI_PTM2MS 0xffc00001 /* 4MB, enable */
-#define CFG_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */
+#define CFG_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */
+#define CFG_PCI_SUBSYS_DEVICEID 0x0411 /* PCI Device ID: ORSG */
+#define CFG_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/
+#define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */
+#define CFG_PCI_PTM1MS 0xfc000001 /* 64MB, enable hard-wired to 1 */
+#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
+#define CFG_PCI_PTM2LA 0xffc00000 /* point to flash */
+#define CFG_PCI_PTM2MS 0xffc00001 /* 4MB, enable */
+#define CFG_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */
/*-----------------------------------------------------------------------
* Start addresses for the final memory configuration
@@ -157,18 +157,18 @@
#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
-#define CFG_FLASH_WORD_SIZE unsigned short /* flash word size (width) */
-#define CFG_FLASH_ADDR0 0x5555 /* 1st address for flash config cycles */
-#define CFG_FLASH_ADDR1 0x2AAA /* 2nd address for flash config cycles */
+#define CFG_FLASH_WORD_SIZE unsigned short /* flash word size (width) */
+#define CFG_FLASH_ADDR0 0x5555 /* 1st address for flash config cycles */
+#define CFG_FLASH_ADDR1 0x2AAA /* 2nd address for flash config cycles */
/*
* The following defines are added for buggy IOP480 byte interface.
* All other boards should use the standard values (CPCI405 etc.)
*/
-#define CFG_FLASH_READ0 0x0000 /* 0 is standard */
-#define CFG_FLASH_READ1 0x0001 /* 1 is standard */
-#define CFG_FLASH_READ2 0x0002 /* 2 is standard */
+#define CFG_FLASH_READ0 0x0000 /* 0 is standard */
+#define CFG_FLASH_READ1 0x0001 /* 1 is standard */
+#define CFG_FLASH_READ2 0x0002 /* 2 is standard */
-#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
+#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
#if 0 /* Use NVRAM for environment variables */
/*-----------------------------------------------------------------------
@@ -184,9 +184,9 @@
#else /* Use EEPROM for environment variables */
-#define CFG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
-#define CFG_ENV_OFFSET 0x000 /* environment starts at the beginning of the EEPROM */
-#define CFG_ENV_SIZE 0x300 /* 768 bytes may be used for env vars */
+#define CFG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
+#define CFG_ENV_OFFSET 0x000 /* environment starts at the beginning of the EEPROM */
+#define CFG_ENV_SIZE 0x300 /* 768 bytes may be used for env vars */
/* total size of a CAT24WC08 is 1024 bytes */
#endif
@@ -198,12 +198,12 @@
#define CFG_I2C_SLAVE 0x7F
#define CFG_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC08 */
-#define CFG_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
-/* mask of address bits that overflow into the "EEPROM chip address" */
+#define CFG_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
+/* mask of address bits that overflow into the "EEPROM chip address" */
#define CFG_I2C_EEPROM_ADDR_OVERFLOW 0x07
#define CFG_EEPROM_PAGE_WRITE_BITS 4 /* The Catalyst CAT24WC08 has */
/* 16 byte page write mode using*/
- /* last 4 bits of the address */
+ /* last 4 bits of the address */
#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
#define CFG_EEPROM_PAGE_WRITE_ENABLE
@@ -229,53 +229,53 @@
* External Bus Controller (EBC) Setup
*/
-/* Memory Bank 0 (Flash Bank 0) initialization */
-#define CFG_EBC_PB0AP 0x92015480
-#define CFG_EBC_PB0CR 0xFFC5A000 /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
+/* Memory Bank 0 (Flash Bank 0) initialization */
+#define CFG_EBC_PB0AP 0x92015480
+#define CFG_EBC_PB0CR 0xFFC5A000 /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
-/* Memory Bank 1 (Flash Bank 1) initialization */
-#define CFG_EBC_PB1AP 0x92015480
-#define CFG_EBC_PB1CR 0xFF85A000 /* BAS=0xFF8,BS=4MB,BU=R/W,BW=16bit */
+/* Memory Bank 1 (Flash Bank 1) initialization */
+#define CFG_EBC_PB1AP 0x92015480
+#define CFG_EBC_PB1CR 0xFF85A000 /* BAS=0xFF8,BS=4MB,BU=R/W,BW=16bit */
-/* Memory Bank 2 (PLD - FPGA-boot) initialization */
-#define CFG_EBC_PB2AP 0x02015480 /* BME=0x0,TWT=0x04,CSN=0x0,OEN=0x1 */
+/* Memory Bank 2 (PLD - FPGA-boot) initialization */
+#define CFG_EBC_PB2AP 0x02015480 /* BME=0x0,TWT=0x04,CSN=0x0,OEN=0x1 */
/* WBN=0x1,WBF=0x1,TH=0x2,RE=0x0,SOR=0x1,BEM=0x0,PEN=0x0*/
-#define CFG_EBC_PB2CR 0xF0018000 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */
+#define CFG_EBC_PB2CR 0xF0018000 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */
-/* Memory Bank 3 (PLD - OSL) initialization */
-#define CFG_EBC_PB3AP 0x02015480 /* BME=0x0,TWT=0x04,CSN=0x0,OEN=0x1 */
+/* Memory Bank 3 (PLD - OSL) initialization */
+#define CFG_EBC_PB3AP 0x02015480 /* BME=0x0,TWT=0x04,CSN=0x0,OEN=0x1 */
/* WBN=0x1,WBF=0x1,TH=0x2,RE=0x0,SOR=0x1,BEM=0x0,PEN=0x0*/
-#define CFG_EBC_PB3CR 0xF0118000 /* BAS=0xF01,BS=1MB,BU=R/W,BW=8bit */
+#define CFG_EBC_PB3CR 0xF0118000 /* BAS=0xF01,BS=1MB,BU=R/W,BW=8bit */
-/* Memory Bank 4 (Spartan2 1) initialization */
-#define CFG_EBC_PB4AP 0x02015580 /* BME=0x0,TWT=0x04,CSN=0x0,OEN=0x1 */
+/* Memory Bank 4 (Spartan2 1) initialization */
+#define CFG_EBC_PB4AP 0x02015580 /* BME=0x0,TWT=0x04,CSN=0x0,OEN=0x1 */
/* WBN=0x1,WBF=0x1,TH=0x2,RE=0x1,SOR=0x1,BEM=0x0,PEN=0x0*/
-#define CFG_EBC_PB4CR 0xF209C000 /* BAS=0xF20,BS=16MB,BU=R/W,BW=32bit*/
+#define CFG_EBC_PB4CR 0xF209C000 /* BAS=0xF20,BS=16MB,BU=R/W,BW=32bit*/
-/* Memory Bank 5 (Spartan2 2) initialization */
-#define CFG_EBC_PB5AP 0x02015580 /* BME=0x0,TWT=0x04,CSN=0x0,OEN=0x1 */
+/* Memory Bank 5 (Spartan2 2) initialization */
+#define CFG_EBC_PB5AP 0x02015580 /* BME=0x0,TWT=0x04,CSN=0x0,OEN=0x1 */
/* WBN=0x1,WBF=0x1,TH=0x2,RE=0x1,SOR=0x1,BEM=0x0,PEN=0x0*/
-#define CFG_EBC_PB5CR 0xF309C000 /* BAS=0xF30,BS=16MB,BU=R/W,BW=32bit*/
+#define CFG_EBC_PB5CR 0xF309C000 /* BAS=0xF30,BS=16MB,BU=R/W,BW=32bit*/
-/* Memory Bank 6 (Virtex 1) initialization */
-#define CFG_EBC_PB6AP 0x02015580 /* BME=0x0,TWT=0x04,CSN=0x0,OEN=0x1 */
+/* Memory Bank 6 (Virtex 1) initialization */
+#define CFG_EBC_PB6AP 0x02015580 /* BME=0x0,TWT=0x04,CSN=0x0,OEN=0x1 */
/* WBN=0x1,WBF=0x1,TH=0x2,RE=0x1,SOR=0x1,BEM=0x0,PEN=0x0*/
-#define CFG_EBC_PB6CR 0xF409A000 /* BAS=0xF40,BS=16MB,BU=R/W,BW=16bit*/
+#define CFG_EBC_PB6CR 0xF409A000 /* BAS=0xF40,BS=16MB,BU=R/W,BW=16bit*/
-/* Memory Bank 7 (Virtex 2) initialization */
-#define CFG_EBC_PB7AP 0x02015580 /* BME=0x0,TWT=0x04,CSN=0x0,OEN=0x1 */
+/* Memory Bank 7 (Virtex 2) initialization */
+#define CFG_EBC_PB7AP 0x02015580 /* BME=0x0,TWT=0x04,CSN=0x0,OEN=0x1 */
/* WBN=0x1,WBF=0x1,TH=0x2,RE=0x1,SOR=0x1,BEM=0x0,PEN=0x0*/
-#define CFG_EBC_PB7CR 0xF509A000 /* BAS=0xF50,BS=16MB,BU=R/W,BW=16bit*/
+#define CFG_EBC_PB7CR 0xF509A000 /* BAS=0xF50,BS=16MB,BU=R/W,BW=16bit*/
-#define CFG_ETHERNET_MAC_ADDR 0x00000000 /* Pass Ethernet MAC to VxWorks */
+#define CFG_ETHERNET_MAC_ADDR 0x00000000 /* Pass Ethernet MAC to VxWorks */
/*-----------------------------------------------------------------------
* Definitions for initial stack pointer and data area (in DPRAM)
*/
/* use on chip memory ( OCM ) for temperary stack until sdram is tested */
-#define CFG_TEMP_STACK_OCM 1
+#define CFG_TEMP_STACK_OCM 1
/* On Chip Memory location */
#define CFG_OCM_DATA_ADDR 0xF8000000
@@ -285,7 +285,7 @@
#define CFG_INIT_RAM_END CFG_OCM_DATA_SIZE /* End of used area in RAM */
#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
/*
diff --git a/include/configs/OXC.h b/include/configs/OXC.h
index 57f577d2..586b19f 100644
--- a/include/configs/OXC.h
+++ b/include/configs/OXC.h
@@ -39,7 +39,7 @@
#define CONFIG_MPC8240 1
#define CONFIG_OXC 1
-#define CONFIG_BOARD_PRE_INIT 1 /* Call board_pre_init */
+#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
#define CONFIG_IDENT_STRING " [oxc] "
diff --git a/include/configs/P3G4.h b/include/configs/P3G4.h
index b6ebc5f..c56ad11 100644
--- a/include/configs/P3G4.h
+++ b/include/configs/P3G4.h
@@ -51,7 +51,7 @@
/* which initialization functions to call for this board */
#define CONFIG_MISC_INIT_R 1
-#define CONFIG_BOARD_PRE_INIT 1
+#define CONFIG_BOARD_EARLY_INIT_F 1
#define CFG_BOARD_NAME "P3G4"
diff --git a/include/configs/PCI405.h b/include/configs/PCI405.h
index 9cd8f5a..49fdfdd 100644
--- a/include/configs/PCI405.h
+++ b/include/configs/PCI405.h
@@ -34,22 +34,22 @@
*/
#define CONFIG_405GP 1 /* This is a PPC405 CPU */
-#define CONFIG_4xx 1 /* ...member of PPC4xx family */
-#define CONFIG_PCI405 1 /* ...on a PCI405 board */
+#define CONFIG_4xx 1 /* ...member of PPC4xx family */
+#define CONFIG_PCI405 1 /* ...on a PCI405 board */
-#define CONFIG_BOARD_PRE_INIT 1 /* call board_pre_init() */
+#define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */
#define CONFIG_MISC_INIT_R 1 /* call misc_init_r() on init */
-#define CONFIG_SYS_CLK_FREQ 25000000 /* external frequency to pll */
+#define CONFIG_SYS_CLK_FREQ 25000000 /* external frequency to pll */
#define CONFIG_BAUDRATE 115200
#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */
#if 0
-#define CONFIG_PREBOOT \
- "crc32 f0207004 ffc 0;" \
- "if cmp 0 f0207000 1;" \
- "then;echo Old CRC is correct;crc32 f0207004 ff4 f0207000;" \
+#define CONFIG_PREBOOT \
+ "crc32 f0207004 ffc 0;" \
+ "if cmp 0 f0207000 1;" \
+ "then;echo Old CRC is correct;crc32 f0207004 ff4 f0207000;" \
"else;echo Old CRC is bad;fi"
#endif
@@ -59,8 +59,8 @@
"bootm fffc0000"
#else
#define CONFIG_BOOTCOMMAND \
- "mw.l 0 ffffffff; mw.l 4 ffffffff;" \
- "while cmp 0 4 1; do echo Waiting for Host...;done;" \
+ "mw.l 0 ffffffff; mw.l 4 ffffffff;" \
+ "while cmp 0 4 1; do echo Waiting for Host...;done;" \
"bootm 400000"
#endif
@@ -68,7 +68,7 @@
#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
#define CONFIG_MII 1 /* MII PHY management */
-#define CONFIG_PHY_ADDR 0 /* PHY address */
+#define CONFIG_PHY_ADDR 0 /* PHY address */
#define CONFIG_RTC_M48T35A 1 /* ST Electronics M48 timekeeper */
@@ -79,16 +79,16 @@
CFG_CMD_DATE | \
CFG_CMD_I2C | \
CFG_CMD_BSP | \
- CFG_CMD_EEPROM )
+ CFG_CMD_EEPROM )
/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
#include <cmd_confdefs.h>
-#undef CONFIG_WATCHDOG /* watchdog disabled */
+#undef CONFIG_WATCHDOG /* watchdog disabled */
-#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */
+#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */
-#define CONFIG_PRAM 2048 /* reserve 2 MB "protected RAM" */
+#define CONFIG_PRAM 2048 /* reserve 2 MB "protected RAM" */
/*
* Miscellaneous configurable options
@@ -96,75 +96,75 @@
#define CFG_LONGHELP /* undef to save memory */
#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#define CFG_HUSH_PARSER /* use "hush" command parser */
+#define CFG_HUSH_PARSER /* use "hush" command parser */
#ifdef CFG_HUSH_PARSER
-#define CFG_PROMPT_HUSH_PS2 "> "
+#define CFG_PROMPT_HUSH_PS2 "> "
#endif
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
#endif
#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
#define CFG_MAXARGS 16 /* max number of command args */
#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_DEVICE_NULLDEV 1 /* include nulldev device */
+#define CFG_DEVICE_NULLDEV 1 /* include nulldev device */
-#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
+#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-#undef CFG_EXT_SERIAL_CLOCK /* no external serial clock used */
-#define CFG_IGNORE_405_UART_ERRATA_59 /* ignore ppc405gp errata #59 */
-#define CFG_BASE_BAUD 691200
+#undef CFG_EXT_SERIAL_CLOCK /* no external serial clock used */
+#define CFG_IGNORE_405_UART_ERRATA_59 /* ignore ppc405gp errata #59 */
+#define CFG_BASE_BAUD 691200
/* The following table includes the supported baudrates */
-#define CFG_BAUDRATE_TABLE \
+#define CFG_BAUDRATE_TABLE \
{ 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \
57600, 115200, 230400, 460800, 921600 }
#define CFG_LOAD_ADDR 0x100000 /* default load address */
#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
#undef CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
+#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
/*-----------------------------------------------------------------------
* PCI stuff
*-----------------------------------------------------------------------
*/
-#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */
-#define PCI_HOST_FORCE 1 /* configure as pci host */
-#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
+#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */
+#define PCI_HOST_FORCE 1 /* configure as pci host */
+#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
-#define CONFIG_PCI /* include pci support */
-#define CONFIG_PCI_HOST PCI_HOST_ADAPTER /* select pci host function */
-#undef CONFIG_PCI_PNP /* no pci plug-and-play */
- /* resource configuration */
+#define CONFIG_PCI /* include pci support */
+#define CONFIG_PCI_HOST PCI_HOST_ADAPTER /* select pci host function */
+#undef CONFIG_PCI_PNP /* no pci plug-and-play */
+ /* resource configuration */
-#define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */
+#define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */
-#define CFG_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */
-#define CFG_PCI_SUBSYS_DEVICEID 0x0407 /* PCI Device ID: PCI-405 */
-#define CFG_PCI_CLASSCODE 0x0280 /* PCI Class Code: Network/Other*/
-#define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */
-#define CFG_PCI_PTM1MS 0xff000001 /* 16MB, enable hard-wired to 1 */
-#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
+#define CFG_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */
+#define CFG_PCI_SUBSYS_DEVICEID 0x0407 /* PCI Device ID: PCI-405 */
+#define CFG_PCI_CLASSCODE 0x0280 /* PCI Class Code: Network/Other*/
+#define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */
+#define CFG_PCI_PTM1MS 0xff000001 /* 16MB, enable hard-wired to 1 */
+#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
#if 0 /* test-only */
-#define CFG_PCI_PTM2LA 0xffc00000 /* point to flash */
-#define CFG_PCI_PTM2MS 0xffc00001 /* 4MB, enable */
-#define CFG_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */
+#define CFG_PCI_PTM2LA 0xffc00000 /* point to flash */
+#define CFG_PCI_PTM2MS 0xffc00001 /* 4MB, enable */
+#define CFG_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */
#else
-#define CFG_PCI_PTM2LA 0xef600000 /* point to internal regs */
-#define CFG_PCI_PTM2MS 0xffe00001 /* 2MB, enable */
-#define CFG_PCI_PTM2PCI 0x00000000 /* Host: use this pci address */
+#define CFG_PCI_PTM2LA 0xef600000 /* point to internal regs */
+#define CFG_PCI_PTM2MS 0xffe00001 /* 2MB, enable */
+#define CFG_PCI_PTM2PCI 0x00000000 /* Host: use this pci address */
#endif
/*-----------------------------------------------------------------------
@@ -193,18 +193,18 @@
#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
-#define CFG_FLASH_WORD_SIZE unsigned short /* flash word size (width) */
-#define CFG_FLASH_ADDR0 0x5555 /* 1st address for flash config cycles */
-#define CFG_FLASH_ADDR1 0x2AAA /* 2nd address for flash config cycles */
+#define CFG_FLASH_WORD_SIZE unsigned short /* flash word size (width) */
+#define CFG_FLASH_ADDR0 0x5555 /* 1st address for flash config cycles */
+#define CFG_FLASH_ADDR1 0x2AAA /* 2nd address for flash config cycles */
/*
* The following defines are added for buggy IOP480 byte interface.
* All other boards should use the standard values (CPCI405 etc.)
*/
-#define CFG_FLASH_READ0 0x0000 /* 0 is standard */
-#define CFG_FLASH_READ1 0x0001 /* 1 is standard */
-#define CFG_FLASH_READ2 0x0002 /* 2 is standard */
+#define CFG_FLASH_READ0 0x0000 /* 0 is standard */
+#define CFG_FLASH_READ1 0x0001 /* 1 is standard */
+#define CFG_FLASH_READ2 0x0002 /* 2 is standard */
-#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
+#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
#if 0 /* Use NVRAM for environment variables */
/*-----------------------------------------------------------------------
@@ -217,9 +217,9 @@
#else /* Use EEPROM for environment variables */
-#define CFG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
-#define CFG_ENV_OFFSET 0x000 /* environment starts at the beginning of the EEPROM */
-#define CFG_ENV_SIZE 0x400 /* 1024 bytes may be used for env vars*/
+#define CFG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
+#define CFG_ENV_OFFSET 0x000 /* environment starts at the beginning of the EEPROM */
+#define CFG_ENV_SIZE 0x400 /* 1024 bytes may be used for env vars*/
/* total size of a CAT24WC08 is 1024 bytes */
#endif
@@ -234,12 +234,12 @@
#define CFG_I2C_SLAVE 0x7F
#define CFG_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC08 */
-#define CFG_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
-/* mask of address bits that overflow into the "EEPROM chip address" */
+#define CFG_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
+/* mask of address bits that overflow into the "EEPROM chip address" */
#define CFG_I2C_EEPROM_ADDR_OVERFLOW 0x07
#define CFG_EEPROM_PAGE_WRITE_BITS 4 /* The Catalyst CAT24WC08 has */
/* 16 byte page write mode using*/
- /* last 4 bits of the address */
+ /* last 4 bits of the address */
#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
#define CFG_EEPROM_PAGE_WRITE_ENABLE
@@ -264,73 +264,73 @@
* External Bus Controller (EBC) Setup
*/
-/* Memory Bank 0 (Flash Bank 0) initialization */
-#define CFG_EBC_PB0AP 0x92015480
-#define CFG_EBC_PB0CR 0xFFC5A000 /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
+/* Memory Bank 0 (Flash Bank 0) initialization */
+#define CFG_EBC_PB0AP 0x92015480
+#define CFG_EBC_PB0CR 0xFFC5A000 /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
-/* Memory Bank 1 (NVRAM/RTC) initialization */
-#define CFG_EBC_PB1AP 0x01005280 /* TWT=2,WBN=1,WBF=1,TH=1,SOR=1 */
-#define CFG_EBC_PB1CR 0xF0218000 /* BAS=0xF02,BS=1MB,BU=R/W,BW=8bit */
+/* Memory Bank 1 (NVRAM/RTC) initialization */
+#define CFG_EBC_PB1AP 0x01005280 /* TWT=2,WBN=1,WBF=1,TH=1,SOR=1 */
+#define CFG_EBC_PB1CR 0xF0218000 /* BAS=0xF02,BS=1MB,BU=R/W,BW=8bit */
-/* Memory Bank 2 (CAN0, 1) initialization */
-#define CFG_EBC_PB2AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
-/*#define CFG_EBC_PB2AP 0x038056C0 / * BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
-#define CFG_EBC_PB2CR 0xF0018000 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */
+/* Memory Bank 2 (CAN0, 1) initialization */
+#define CFG_EBC_PB2AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
+/*#define CFG_EBC_PB2AP 0x038056C0 / * BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
+#define CFG_EBC_PB2CR 0xF0018000 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */
-/* Memory Bank 3 (FPGA internal) initialization */
-#define CFG_EBC_PB3AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
-#define CFG_EBC_PB3CR 0xF041C000 /* BAS=0xF01,BS=1MB,BU=R/W,BW=32bit */
-#define CFG_FPGA_BASE_ADDR 0xF0400000
+/* Memory Bank 3 (FPGA internal) initialization */
+#define CFG_EBC_PB3AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
+#define CFG_EBC_PB3CR 0xF041C000 /* BAS=0xF01,BS=1MB,BU=R/W,BW=32bit */
+#define CFG_FPGA_BASE_ADDR 0xF0400000
/*-----------------------------------------------------------------------
* FPGA stuff
*/
/* FPGA internal regs */
-#define CFG_FPGA_MODE 0x00
-#define CFG_FPGA_STATUS 0x02
-#define CFG_FPGA_TS 0x04
-#define CFG_FPGA_TS_LOW 0x06
-#define CFG_FPGA_TS_CAP0 0x10
-#define CFG_FPGA_TS_CAP0_LOW 0x12
-#define CFG_FPGA_TS_CAP1 0x14
-#define CFG_FPGA_TS_CAP1_LOW 0x16
-#define CFG_FPGA_TS_CAP2 0x18
-#define CFG_FPGA_TS_CAP2_LOW 0x1a
-#define CFG_FPGA_TS_CAP3 0x1c
-#define CFG_FPGA_TS_CAP3_LOW 0x1e
+#define CFG_FPGA_MODE 0x00
+#define CFG_FPGA_STATUS 0x02
+#define CFG_FPGA_TS 0x04
+#define CFG_FPGA_TS_LOW 0x06
+#define CFG_FPGA_TS_CAP0 0x10
+#define CFG_FPGA_TS_CAP0_LOW 0x12
+#define CFG_FPGA_TS_CAP1 0x14
+#define CFG_FPGA_TS_CAP1_LOW 0x16
+#define CFG_FPGA_TS_CAP2 0x18
+#define CFG_FPGA_TS_CAP2_LOW 0x1a
+#define CFG_FPGA_TS_CAP3 0x1c
+#define CFG_FPGA_TS_CAP3_LOW 0x1e
/* FPGA Mode Reg */
-#define CFG_FPGA_MODE_CF_RESET 0x0001
+#define CFG_FPGA_MODE_CF_RESET 0x0001
#define CFG_FPGA_MODE_TS_IRQ_ENABLE 0x0100
#define CFG_FPGA_MODE_TS_IRQ_CLEAR 0x1000
-#define CFG_FPGA_MODE_TS_CLEAR 0x2000
+#define CFG_FPGA_MODE_TS_CLEAR 0x2000
/* FPGA Status Reg */
-#define CFG_FPGA_STATUS_DIP0 0x0001
-#define CFG_FPGA_STATUS_DIP1 0x0002
-#define CFG_FPGA_STATUS_DIP2 0x0004
-#define CFG_FPGA_STATUS_FLASH 0x0008
-#define CFG_FPGA_STATUS_TS_IRQ 0x1000
+#define CFG_FPGA_STATUS_DIP0 0x0001
+#define CFG_FPGA_STATUS_DIP1 0x0002
+#define CFG_FPGA_STATUS_DIP2 0x0004
+#define CFG_FPGA_STATUS_FLASH 0x0008
+#define CFG_FPGA_STATUS_TS_IRQ 0x1000
-#define CFG_FPGA_SPARTAN2 1 /* using Xilinx Spartan 2 now */
-#define CFG_FPGA_MAX_SIZE 32*1024 /* 32kByte is enough for XC2S15 */
+#define CFG_FPGA_SPARTAN2 1 /* using Xilinx Spartan 2 now */
+#define CFG_FPGA_MAX_SIZE 32*1024 /* 32kByte is enough for XC2S15 */
/* FPGA program pin configuration */
-#define CFG_FPGA_PRG 0x04000000 /* FPGA program pin (ppc output) */
-#define CFG_FPGA_CLK 0x02000000 /* FPGA clk pin (ppc output) */
-#define CFG_FPGA_DATA 0x01000000 /* FPGA data pin (ppc output) */
-#define CFG_FPGA_INIT 0x00400000 /* FPGA init pin (ppc input) */
-#define CFG_FPGA_DONE 0x00800000 /* FPGA done pin (ppc input) */
+#define CFG_FPGA_PRG 0x04000000 /* FPGA program pin (ppc output) */
+#define CFG_FPGA_CLK 0x02000000 /* FPGA clk pin (ppc output) */
+#define CFG_FPGA_DATA 0x01000000 /* FPGA data pin (ppc output) */
+#define CFG_FPGA_INIT 0x00400000 /* FPGA init pin (ppc input) */
+#define CFG_FPGA_DONE 0x00800000 /* FPGA done pin (ppc input) */
/*-----------------------------------------------------------------------
* Definitions for initial stack pointer and data area (in data cache)
*/
-#define CFG_INIT_DCACHE_CS 7 /* use cs # 7 for data cache memory */
-#define CFG_INIT_RAM_ADDR 0x40000000 /* use data cache */
-#define CFG_INIT_RAM_END 0x2000 /* End of used area in RAM */
+#define CFG_INIT_DCACHE_CS 7 /* use cs # 7 for data cache memory */
+#define CFG_INIT_RAM_ADDR 0x40000000 /* use data cache */
+#define CFG_INIT_RAM_END 0x2000 /* End of used area in RAM */
#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
/*
* Internal Definitions
diff --git a/include/configs/PCIPPC2.h b/include/configs/PCIPPC2.h
index 645cdc5..f90c52e 100644
--- a/include/configs/PCIPPC2.h
+++ b/include/configs/PCIPPC2.h
@@ -43,7 +43,7 @@
#define CONFIG_PCIPPC2 1 /* this is a PCIPPC2 board */
-#define CONFIG_BOARD_PRE_INIT 1
+#define CONFIG_BOARD_EARLY_INIT_F 1
#define CONFIG_MISC_INIT_R 1
#define CONFIG_CONS_INDEX 1
diff --git a/include/configs/PCIPPC6.h b/include/configs/PCIPPC6.h
index 4953458..f4a5dd8 100644
--- a/include/configs/PCIPPC6.h
+++ b/include/configs/PCIPPC6.h
@@ -43,7 +43,7 @@
#define CONFIG_PCIPPC2 1 /* this is a PCIPPC2 board */
-#define CONFIG_BOARD_PRE_INIT 1
+#define CONFIG_BOARD_EARLY_INIT_F 1
#define CONFIG_MISC_INIT_R 1
#define CONFIG_CONS_INDEX 1
diff --git a/include/configs/PIP405.h b/include/configs/PIP405.h
index 2cd5726..dbec242 100644
--- a/include/configs/PIP405.h
+++ b/include/configs/PIP405.h
@@ -103,7 +103,7 @@
***************************************************************/
#define SPD_EEPROM_ADDRESS 0x50
-#define CONFIG_BOARD_PRE_INIT
+#define CONFIG_BOARD_EARLY_INIT_F
/**************************************************************
* Environment definitions
**************************************************************/
@@ -238,7 +238,7 @@
/* Size: 0=1MB, 1=2MB, 2=4MB, 3=8MB, 4=16MB, 5=32MB, 6=64MB, 7=128MB */
#define FLASH_SIZE_PRELIM 3 /* maximal flash FLASH size bank #0 */
-#define CONFIG_BOARD_PRE_INIT
+#define CONFIG_BOARD_EARLY_INIT_F
/* Configuration Port location */
#define CONFIG_PORT_ADDR 0xF4000000
diff --git a/include/configs/PLU405.h b/include/configs/PLU405.h
index d93deff..0798af4 100644
--- a/include/configs/PLU405.h
+++ b/include/configs/PLU405.h
@@ -34,13 +34,13 @@
*/
#define CONFIG_405EP 1 /* This is a PPC405 CPU */
-#define CONFIG_4xx 1 /* ...member of PPC4xx family */
-#define CONFIG_PLU405 1 /* ...on a PLU405 board */
+#define CONFIG_4xx 1 /* ...member of PPC4xx family */
+#define CONFIG_PLU405 1 /* ...on a PLU405 board */
-#define CONFIG_BOARD_PRE_INIT 1 /* call board_pre_init() */
-#define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */
+#define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */
+#define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */
-#define CONFIG_SYS_CLK_FREQ 33333334 /* external frequency to pll */
+#define CONFIG_SYS_CLK_FREQ 33333334 /* external frequency to pll */
#define CONFIG_BAUDRATE 9600
#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */
@@ -60,7 +60,7 @@
#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
#define CONFIG_MII 1 /* MII PHY management */
-#define CONFIG_PHY_ADDR 0 /* PHY address */
+#define CONFIG_PHY_ADDR 0 /* PHY address */
#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \
CFG_CMD_DHCP | \
@@ -73,7 +73,7 @@
CFG_CMD_I2C | \
CFG_CMD_MII | \
CFG_CMD_PING | \
- CFG_CMD_EEPROM )
+ CFG_CMD_EEPROM )
#define CONFIG_MAC_PARTITION
#define CONFIG_DOS_PARTITION
@@ -81,12 +81,12 @@
/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
#include <cmd_confdefs.h>
-#undef CONFIG_WATCHDOG /* watchdog disabled */
+#undef CONFIG_WATCHDOG /* watchdog disabled */
-#define CONFIG_RTC_MC146818 /* DS1685 is MC146818 compatible*/
-#define CFG_RTC_REG_BASE_ADDR 0xF0000500 /* RTC Base Address */
+#define CONFIG_RTC_MC146818 /* DS1685 is MC146818 compatible*/
+#define CFG_RTC_REG_BASE_ADDR 0xF0000500 /* RTC Base Address */
-#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */
+#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */
/*
* Miscellaneous configurable options
@@ -96,45 +96,45 @@
#undef CFG_HUSH_PARSER /* use "hush" command parser */
#ifdef CFG_HUSH_PARSER
-#define CFG_PROMPT_HUSH_PS2 "> "
+#define CFG_PROMPT_HUSH_PS2 "> "
#endif
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
#endif
#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
#define CFG_MAXARGS 16 /* max number of command args */
#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_DEVICE_NULLDEV 1 /* include nulldev device */
+#define CFG_DEVICE_NULLDEV 1 /* include nulldev device */
-#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
+#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-#undef CFG_EXT_SERIAL_CLOCK /* no external serial clock used */
-#define CFG_IGNORE_405_UART_ERRATA_59 /* ignore ppc405gp errata #59 */
-#define CFG_BASE_BAUD 691200
-#undef CONFIG_UART1_CONSOLE /* define for uart1 as console */
+#undef CFG_EXT_SERIAL_CLOCK /* no external serial clock used */
+#define CFG_IGNORE_405_UART_ERRATA_59 /* ignore ppc405gp errata #59 */
+#define CFG_BASE_BAUD 691200
+#undef CONFIG_UART1_CONSOLE /* define for uart1 as console */
/* The following table includes the supported baudrates */
-#define CFG_BAUDRATE_TABLE \
+#define CFG_BAUDRATE_TABLE \
{ 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \
57600, 115200, 230400, 460800, 921600 }
#define CFG_LOAD_ADDR 0x100000 /* default load address */
#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
+#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
-#define CFG_RX_ETH_BUFFER 16 /* use 16 rx buffer on 405 emac */
+#define CFG_RX_ETH_BUFFER 16 /* use 16 rx buffer on 405 emac */
/*-----------------------------------------------------------------------
* NAND-FLASH stuff
@@ -147,14 +147,14 @@
#define ADDR_PAGE 2
#define ADDR_COLUMN_PAGE 3
-#define NAND_ChipID_UNKNOWN 0x00
+#define NAND_ChipID_UNKNOWN 0x00
#define NAND_MAX_FLOORS 1
#define NAND_MAX_CHIPS 1
-#define CFG_NAND_CE (0x80000000 >> 1) /* our CE is GPIO1 */
-#define CFG_NAND_CLE (0x80000000 >> 2) /* our CLE is GPIO2 */
-#define CFG_NAND_ALE (0x80000000 >> 3) /* our ALE is GPIO3 */
-#define CFG_NAND_RDY (0x80000000 >> 4) /* our RDY is GPIO4 */
+#define CFG_NAND_CE (0x80000000 >> 1) /* our CE is GPIO1 */
+#define CFG_NAND_CLE (0x80000000 >> 2) /* our CLE is GPIO2 */
+#define CFG_NAND_ALE (0x80000000 >> 3) /* our ALE is GPIO3 */
+#define CFG_NAND_RDY (0x80000000 >> 4) /* our RDY is GPIO4 */
#define NAND_DISABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CE);} while(0)
#define NAND_ENABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CE);} while(0)
@@ -173,43 +173,43 @@
* PCI stuff
*-----------------------------------------------------------------------
*/
-#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */
-#define PCI_HOST_FORCE 1 /* configure as pci host */
-#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
+#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */
+#define PCI_HOST_FORCE 1 /* configure as pci host */
+#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
-#define CONFIG_PCI /* include pci support */
-#define CONFIG_PCI_HOST PCI_HOST_HOST /* select pci host function */
-#define CONFIG_PCI_PNP /* do pci plug-and-play */
- /* resource configuration */
+#define CONFIG_PCI /* include pci support */
+#define CONFIG_PCI_HOST PCI_HOST_HOST /* select pci host function */
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
+ /* resource configuration */
-#define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */
+#define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */
-#define CFG_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */
-#define CFG_PCI_SUBSYS_DEVICEID 0x0405 /* PCI Device ID: CPCI-405 */
-#define CFG_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/
-#define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */
-#define CFG_PCI_PTM1MS 0xfc000001 /* 64MB, enable hard-wired to 1 */
-#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
-#define CFG_PCI_PTM2LA 0xffc00000 /* point to flash */
-#define CFG_PCI_PTM2MS 0xffc00001 /* 4MB, enable */
-#define CFG_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */
+#define CFG_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */
+#define CFG_PCI_SUBSYS_DEVICEID 0x0405 /* PCI Device ID: CPCI-405 */
+#define CFG_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/
+#define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */
+#define CFG_PCI_PTM1MS 0xfc000001 /* 64MB, enable hard-wired to 1 */
+#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
+#define CFG_PCI_PTM2LA 0xffc00000 /* point to flash */
+#define CFG_PCI_PTM2MS 0xffc00001 /* 4MB, enable */
+#define CFG_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */
/*-----------------------------------------------------------------------
* IDE/ATA stuff
*-----------------------------------------------------------------------
*/
-#undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */
-#undef CONFIG_IDE_LED /* no led for ide supported */
+#undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */
+#undef CONFIG_IDE_LED /* no led for ide supported */
#define CONFIG_IDE_RESET 1 /* reset for ide supported */
-#define CFG_IDE_MAXBUS 1 /* max. 1 IDE busses */
-#define CFG_IDE_MAXDEVICE (CFG_IDE_MAXBUS*1) /* max. 1 drives per IDE bus */
+#define CFG_IDE_MAXBUS 1 /* max. 1 IDE busses */
+#define CFG_IDE_MAXDEVICE (CFG_IDE_MAXBUS*1) /* max. 1 drives per IDE bus */
-#define CFG_ATA_BASE_ADDR 0xF0100000
-#define CFG_ATA_IDE0_OFFSET 0x0000
+#define CFG_ATA_BASE_ADDR 0xF0100000
+#define CFG_ATA_IDE0_OFFSET 0x0000
#define CFG_ATA_DATA_OFFSET 0x0000 /* Offset for data I/O */
-#define CFG_ATA_REG_OFFSET 0x0000 /* Offset for normal register accesses */
+#define CFG_ATA_REG_OFFSET 0x0000 /* Offset for normal register accesses */
#define CFG_ATA_ALT_OFFSET 0x0000 /* Offset for alternate registers */
/*
@@ -229,22 +229,22 @@
#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
#define CFG_FLASH_WRITE_TOUT 1000 /* Timeout for Flash Write (in ms) */
-#define CFG_FLASH_WORD_SIZE unsigned short /* flash word size (width) */
-#define CFG_FLASH_ADDR0 0x5555 /* 1st address for flash config cycles */
-#define CFG_FLASH_ADDR1 0x2AAA /* 2nd address for flash config cycles */
+#define CFG_FLASH_WORD_SIZE unsigned short /* flash word size (width) */
+#define CFG_FLASH_ADDR0 0x5555 /* 1st address for flash config cycles */
+#define CFG_FLASH_ADDR1 0x2AAA /* 2nd address for flash config cycles */
/*
* The following defines are added for buggy IOP480 byte interface.
* All other boards should use the standard values (CPCI405 etc.)
*/
-#define CFG_FLASH_READ0 0x0000 /* 0 is standard */
-#define CFG_FLASH_READ1 0x0001 /* 1 is standard */
-#define CFG_FLASH_READ2 0x0002 /* 2 is standard */
+#define CFG_FLASH_READ0 0x0000 /* 0 is standard */
+#define CFG_FLASH_READ1 0x0001 /* 1 is standard */
+#define CFG_FLASH_READ2 0x0002 /* 2 is standard */
-#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
+#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
#if 0 /* test-only */
-#define CFG_JFFS2_FIRST_BANK 0 /* use for JFFS2 */
-#define CFG_JFFS2_NUM_BANKS 1 /* ! second bank contains U-Boot */
+#define CFG_JFFS2_FIRST_BANK 0 /* use for JFFS2 */
+#define CFG_JFFS2_NUM_BANKS 1 /* ! second bank contains U-Boot */
#endif
/*-----------------------------------------------------------------------
@@ -267,13 +267,13 @@
/*-----------------------------------------------------------------------
* Environment Variable setup
*/
-#define CFG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
-#define CFG_ENV_OFFSET 0x100 /* environment starts at the beginning of the EEPROM */
-#define CFG_ENV_SIZE 0x700 /* 2048 bytes may be used for env vars*/
+#define CFG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
+#define CFG_ENV_OFFSET 0x100 /* environment starts at the beginning of the EEPROM */
+#define CFG_ENV_SIZE 0x700 /* 2048 bytes may be used for env vars*/
/* total size of a CAT24WC16 is 2048 bytes */
#define CFG_NVRAM_BASE_ADDR 0xF0000500 /* NVRAM base address */
-#define CFG_NVRAM_SIZE 242 /* NVRAM size */
+#define CFG_NVRAM_SIZE 242 /* NVRAM size */
/*-----------------------------------------------------------------------
* I2C EEPROM (CAT24WC16) for environment
@@ -285,20 +285,20 @@
#define CFG_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT24WC08 */
#if 1 /* test-only */
/* CAT24WC08/16... */
-#define CFG_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
-/* mask of address bits that overflow into the "EEPROM chip address" */
+#define CFG_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
+/* mask of address bits that overflow into the "EEPROM chip address" */
#define CFG_I2C_EEPROM_ADDR_OVERFLOW 0x07
#define CFG_EEPROM_PAGE_WRITE_BITS 4 /* The Catalyst CAT24WC08 has */
/* 16 byte page write mode using*/
- /* last 4 bits of the address */
+ /* last 4 bits of the address */
#else
/* CAT24WC32/64... */
-#define CFG_I2C_EEPROM_ADDR_LEN 2 /* Bytes of address */
-/* mask of address bits that overflow into the "EEPROM chip address" */
+#define CFG_I2C_EEPROM_ADDR_LEN 2 /* Bytes of address */
+/* mask of address bits that overflow into the "EEPROM chip address" */
#define CFG_I2C_EEPROM_ADDR_OVERFLOW 0x01
#define CFG_EEPROM_PAGE_WRITE_BITS 5 /* The Catalyst CAT24WC32 has */
/* 32 byte page write mode using*/
- /* last 5 bits of the address */
+ /* last 5 bits of the address */
#endif
#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
#define CFG_EEPROM_PAGE_WRITE_ENABLE
@@ -306,8 +306,8 @@
/*-----------------------------------------------------------------------
* Cache Configuration
*/
-#define CFG_DCACHE_SIZE 16384 /* For IBM 405 CPUs, older 405 ppc's */
- /* have only 8kB, 16kB is save here */
+#define CFG_DCACHE_SIZE 16384 /* For IBM 405 CPUs, older 405 ppc's */
+ /* have only 8kB, 16kB is save here */
#define CFG_CACHELINE_SIZE 32 /* ... */
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
@@ -317,59 +317,59 @@
* External Bus Controller (EBC) Setup
*/
-#define CAN_BA 0xF0000000 /* CAN Base Address */
-#define DUART0_BA 0xF0000400 /* DUART Base Address */
-#define DUART1_BA 0xF0000408 /* DUART Base Address */
-#define RTC_BA 0xF0000500 /* RTC Base Address */
-#define VGA_BA 0xF1000000 /* Epson VGA Base Address */
-#define CFG_NAND_BASE 0xF4000000 /* NAND FLASH Base Address */
+#define CAN_BA 0xF0000000 /* CAN Base Address */
+#define DUART0_BA 0xF0000400 /* DUART Base Address */
+#define DUART1_BA 0xF0000408 /* DUART Base Address */
+#define RTC_BA 0xF0000500 /* RTC Base Address */
+#define VGA_BA 0xF1000000 /* Epson VGA Base Address */
+#define CFG_NAND_BASE 0xF4000000 /* NAND FLASH Base Address */
-/* Memory Bank 0 (Flash Bank 0, NOR-FLASH) initialization */
-#define CFG_EBC_PB0AP 0x92015480
-/*#define CFG_EBC_PB0AP 0x08055880 /XXX* TWT=16,CSN=1,OEN=1,WBN=1,WBF=1,TH=4,SOR=1 */
-#define CFG_EBC_PB0CR 0xFFC5A000 /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
+/* Memory Bank 0 (Flash Bank 0, NOR-FLASH) initialization */
+#define CFG_EBC_PB0AP 0x92015480
+/*#define CFG_EBC_PB0AP 0x08055880 /XXX* TWT=16,CSN=1,OEN=1,WBN=1,WBF=1,TH=4,SOR=1 */
+#define CFG_EBC_PB0CR 0xFFC5A000 /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
-/* Memory Bank 1 (Flash Bank 1, NAND-FLASH) initialization */
-#define CFG_EBC_PB1AP 0x92015480
-#define CFG_EBC_PB1CR 0xF4018000 /* BAS=0xF40,BS=1MB,BU=R/W,BW=8bit */
+/* Memory Bank 1 (Flash Bank 1, NAND-FLASH) initialization */
+#define CFG_EBC_PB1AP 0x92015480
+#define CFG_EBC_PB1CR 0xF4018000 /* BAS=0xF40,BS=1MB,BU=R/W,BW=8bit */
-/* Memory Bank 2 (8 Bit Peripheral: CAN, UART, RTC) initialization */
-#define CFG_EBC_PB2AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
-#define CFG_EBC_PB2CR 0xF0018000 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */
+/* Memory Bank 2 (8 Bit Peripheral: CAN, UART, RTC) initialization */
+#define CFG_EBC_PB2AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
+#define CFG_EBC_PB2CR 0xF0018000 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */
-/* Memory Bank 3 (16 Bit Peripheral: FPGA internal, dig. IO) initialization */
-#define CFG_EBC_PB3AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
-#define CFG_EBC_PB3CR 0xF011A000 /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */
+/* Memory Bank 3 (16 Bit Peripheral: FPGA internal, dig. IO) initialization */
+#define CFG_EBC_PB3AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
+#define CFG_EBC_PB3CR 0xF011A000 /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */
/*-----------------------------------------------------------------------
* FPGA stuff
*/
-#define CFG_FPGA_BASE_ADDR 0xF0100100 /* FPGA internal Base Address */
+#define CFG_FPGA_BASE_ADDR 0xF0100100 /* FPGA internal Base Address */
/* FPGA internal regs */
-#define CFG_FPGA_CTRL 0x000
+#define CFG_FPGA_CTRL 0x000
/* FPGA Control Reg */
-#define CFG_FPGA_CTRL_CF_RESET 0x0001
-#define CFG_FPGA_CTRL_WDI 0x0002
+#define CFG_FPGA_CTRL_CF_RESET 0x0001
+#define CFG_FPGA_CTRL_WDI 0x0002
#define CFG_FPGA_CTRL_PS2_RESET 0x0020
-#define CFG_FPGA_SPARTAN2 1 /* using Xilinx Spartan 2 now */
-#define CFG_FPGA_MAX_SIZE 128*1024 /* 128kByte is enough for XC2S50E*/
+#define CFG_FPGA_SPARTAN2 1 /* using Xilinx Spartan 2 now */
+#define CFG_FPGA_MAX_SIZE 128*1024 /* 128kByte is enough for XC2S50E*/
/* FPGA program pin configuration */
-#define CFG_FPGA_PRG 0x04000000 /* FPGA program pin (ppc output) */
-#define CFG_FPGA_CLK 0x02000000 /* FPGA clk pin (ppc output) */
-#define CFG_FPGA_DATA 0x01000000 /* FPGA data pin (ppc output) */
-#define CFG_FPGA_INIT 0x00010000 /* FPGA init pin (ppc input) */
-#define CFG_FPGA_DONE 0x00008000 /* FPGA done pin (ppc input) */
+#define CFG_FPGA_PRG 0x04000000 /* FPGA program pin (ppc output) */
+#define CFG_FPGA_CLK 0x02000000 /* FPGA clk pin (ppc output) */
+#define CFG_FPGA_DATA 0x01000000 /* FPGA data pin (ppc output) */
+#define CFG_FPGA_INIT 0x00010000 /* FPGA init pin (ppc input) */
+#define CFG_FPGA_DONE 0x00008000 /* FPGA done pin (ppc input) */
/*-----------------------------------------------------------------------
* Definitions for initial stack pointer and data area (in data cache)
*/
/* use on chip memory ( OCM ) for temperary stack until sdram is tested */
-#define CFG_TEMP_STACK_OCM 1
+#define CFG_TEMP_STACK_OCM 1
/* On Chip Memory location */
#define CFG_OCM_DATA_ADDR 0xF8000000
@@ -379,13 +379,13 @@
#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
/*-----------------------------------------------------------------------
* Definitions for GPIO setup (PPC405EP specific)
*
- * GPIO0[0] - External Bus Controller BLAST output
- * GPIO0[1-9] - Instruction trace outputs -> GPIO
+ * GPIO0[0] - External Bus Controller BLAST output
+ * GPIO0[1-9] - Instruction trace outputs -> GPIO
* GPIO0[10-13] - External Bus Controller CS_1 - CS_4 outputs
* GPIO0[14-16] - External Bus Controller ABUS3-ABUS5 outputs -> GPIO
* GPIO0[17-23] - External Interrupts IRQ0 - IRQ6 inputs
@@ -393,15 +393,15 @@
* GPIO0[28-29] - UART1 data signal input/output
* GPIO0[30-31] - EMAC0 and EMAC1 reject packet inputs
*/
-#define CFG_GPIO0_OSRH 0x40000550
-#define CFG_GPIO0_OSRL 0x00000110
-#define CFG_GPIO0_ISR1H 0x00000000
-#define CFG_GPIO0_ISR1L 0x15555445
-#define CFG_GPIO0_TSRH 0x00000000
-#define CFG_GPIO0_TSRL 0x00000000
-#define CFG_GPIO0_TCR 0xF7FE0014
+#define CFG_GPIO0_OSRH 0x40000550
+#define CFG_GPIO0_OSRL 0x00000110
+#define CFG_GPIO0_ISR1H 0x00000000
+#define CFG_GPIO0_ISR1L 0x15555445
+#define CFG_GPIO0_TSRH 0x00000000
+#define CFG_GPIO0_TSRL 0x00000000
+#define CFG_GPIO0_TCR 0xF7FE0014
-#define CFG_DUART_RST (0x80000000 >> 14)
+#define CFG_DUART_RST (0x80000000 >> 14)
/*
* Internal Definitions
@@ -416,16 +416,16 @@
* This value will be set if iic boot eprom is disabled.
*/
#if 0
-#define PLLMR0_DEFAULT PLLMR0_266_133_66_33
-#define PLLMR1_DEFAULT PLLMR1_266_133_66_33
+#define PLLMR0_DEFAULT PLLMR0_266_133_66_33
+#define PLLMR1_DEFAULT PLLMR1_266_133_66_33
#endif
#if 0
-#define PLLMR0_DEFAULT PLLMR0_200_100_50_33
-#define PLLMR1_DEFAULT PLLMR1_200_100_50_33
+#define PLLMR0_DEFAULT PLLMR0_200_100_50_33
+#define PLLMR1_DEFAULT PLLMR1_200_100_50_33
#endif
#if 1
-#define PLLMR0_DEFAULT PLLMR0_133_66_66_33
-#define PLLMR1_DEFAULT PLLMR1_133_66_66_33
+#define PLLMR0_DEFAULT PLLMR0_133_66_66_33
+#define PLLMR1_DEFAULT PLLMR1_133_66_66_33
#endif
#endif /* __CONFIG_H */
diff --git a/include/configs/PMC405.h b/include/configs/PMC405.h
index 35d49fc..49414bb 100644
--- a/include/configs/PMC405.h
+++ b/include/configs/PMC405.h
@@ -34,13 +34,13 @@
*/
#define CONFIG_405GP 1 /* This is a PPC405 CPU */
-#define CONFIG_4xx 1 /* ...member of PPC4xx family */
-#define CONFIG_PMC405 1 /* ...on a PMC405 board */
+#define CONFIG_4xx 1 /* ...member of PPC4xx family */
+#define CONFIG_PMC405 1 /* ...on a PMC405 board */
-#define CONFIG_BOARD_PRE_INIT 1 /* call board_pre_init() */
-#define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */
+#define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */
+#define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */
-#define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */
+#define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */
#define CONFIG_BAUDRATE 9600
#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */
@@ -60,7 +60,7 @@
#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
#define CONFIG_MII 1 /* MII PHY management */
-#define CONFIG_PHY_ADDR 0 /* PHY address */
+#define CONFIG_PHY_ADDR 0 /* PHY address */
#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \
CFG_CMD_BSP | \
@@ -72,7 +72,7 @@
CFG_CMD_MII | \
CFG_CMD_I2C | \
CFG_CMD_PING | \
- CFG_CMD_EEPROM )
+ CFG_CMD_EEPROM )
#define CONFIG_MAC_PARTITION
#define CONFIG_DOS_PARTITION
@@ -80,12 +80,12 @@
/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
#include <cmd_confdefs.h>
-#undef CONFIG_WATCHDOG /* watchdog disabled */
+#undef CONFIG_WATCHDOG /* watchdog disabled */
-#define CONFIG_RTC_MC146818 /* DS1685 is MC146818 compatible*/
-#define CFG_RTC_REG_BASE_ADDR 0xF0000300 /* RTC Base Address */
+#define CONFIG_RTC_MC146818 /* DS1685 is MC146818 compatible*/
+#define CFG_RTC_REG_BASE_ADDR 0xF0000300 /* RTC Base Address */
-#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */
+#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */
/*
* Miscellaneous configurable options
@@ -95,69 +95,69 @@
#undef CFG_HUSH_PARSER /* use "hush" command parser */
#ifdef CFG_HUSH_PARSER
-#define CFG_PROMPT_HUSH_PS2 "> "
+#define CFG_PROMPT_HUSH_PS2 "> "
#endif
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
#endif
#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
#define CFG_MAXARGS 16 /* max number of command args */
#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_DEVICE_NULLDEV 1 /* include nulldev device */
+#define CFG_DEVICE_NULLDEV 1 /* include nulldev device */
-#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
+#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-#undef CFG_EXT_SERIAL_CLOCK /* no external serial clock used */
-#define CFG_IGNORE_405_UART_ERRATA_59 /* ignore ppc405gp errata #59 */
-#define CFG_BASE_BAUD 691200
+#undef CFG_EXT_SERIAL_CLOCK /* no external serial clock used */
+#define CFG_IGNORE_405_UART_ERRATA_59 /* ignore ppc405gp errata #59 */
+#define CFG_BASE_BAUD 691200
/* The following table includes the supported baudrates */
-#define CFG_BAUDRATE_TABLE \
+#define CFG_BAUDRATE_TABLE \
{ 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \
57600, 115200, 230400, 460800, 921600 }
#define CFG_LOAD_ADDR 0x100000 /* default load address */
#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
+#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
-#define CFG_RX_ETH_BUFFER 16 /* use 16 rx buffer on 405 emac */
+#define CFG_RX_ETH_BUFFER 16 /* use 16 rx buffer on 405 emac */
/*-----------------------------------------------------------------------
* PCI stuff
*-----------------------------------------------------------------------
*/
-#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */
-#define PCI_HOST_FORCE 1 /* configure as pci host */
-#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
+#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */
+#define PCI_HOST_FORCE 1 /* configure as pci host */
+#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
-#define CONFIG_PCI /* include pci support */
-#define CONFIG_PCI_HOST PCI_HOST_FORCE /* select pci host function */
-#define CONFIG_PCI_PNP /* do pci plug-and-play */
- /* resource configuration */
+#define CONFIG_PCI /* include pci support */
+#define CONFIG_PCI_HOST PCI_HOST_FORCE /* select pci host function */
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
+ /* resource configuration */
-#undef CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */
+#undef CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */
-#define CFG_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */
-#define CFG_PCI_SUBSYS_DEVICEID 0x0408 /* PCI Device ID: PMC-405 */
-#define CFG_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/
-#define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */
-#define CFG_PCI_PTM1MS 0xfc000001 /* 64MB, enable hard-wired to 1 */
-#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
-#define CFG_PCI_PTM2LA 0xffc00000 /* point to flash */
-#define CFG_PCI_PTM2MS 0xffc00001 /* 4MB, enable */
-#define CFG_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */
+#define CFG_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */
+#define CFG_PCI_SUBSYS_DEVICEID 0x0408 /* PCI Device ID: PMC-405 */
+#define CFG_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/
+#define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */
+#define CFG_PCI_PTM1MS 0xfc000001 /* 64MB, enable hard-wired to 1 */
+#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
+#define CFG_PCI_PTM2LA 0xffc00000 /* point to flash */
+#define CFG_PCI_PTM2MS 0xffc00001 /* 4MB, enable */
+#define CFG_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */
/*-----------------------------------------------------------------------
* Start addresses for the final memory configuration
@@ -187,21 +187,21 @@
#define CFG_FLASH_BASE 0xFE000000
#define CFG_FLASH_INCREMENT 0x01000000
-#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
+#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
-#define CFG_JFFS2_FIRST_BANK 0 /* use for JFFS2 */
-#define CFG_JFFS2_NUM_BANKS 1 /* ! second bank contains u-boot */
+#define CFG_JFFS2_FIRST_BANK 0 /* use for JFFS2 */
+#define CFG_JFFS2_NUM_BANKS 1 /* ! second bank contains u-boot */
/*-----------------------------------------------------------------------
* Environment Variable setup
*/
-#define CFG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
-#define CFG_ENV_OFFSET 0x000 /* environment starts at the beginning of the EEPROM */
-#define CFG_ENV_SIZE 0x800 /* 2048 bytes may be used for env vars*/
+#define CFG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
+#define CFG_ENV_OFFSET 0x000 /* environment starts at the beginning of the EEPROM */
+#define CFG_ENV_SIZE 0x800 /* 2048 bytes may be used for env vars*/
/* total size of a CAT24WC16 is 2048 bytes */
#define CFG_NVRAM_BASE_ADDR 0xF0000500 /* NVRAM base address */
-#define CFG_NVRAM_SIZE 242 /* NVRAM size */
+#define CFG_NVRAM_SIZE 242 /* NVRAM size */
/*-----------------------------------------------------------------------
* I2C EEPROM (CAT24WC16) for environment
@@ -211,20 +211,20 @@
#define CFG_I2C_SLAVE 0x7F
#define CFG_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC08 */
-#define CFG_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
-/* mask of address bits that overflow into the "EEPROM chip address" */
+#define CFG_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
+/* mask of address bits that overflow into the "EEPROM chip address" */
#define CFG_I2C_EEPROM_ADDR_OVERFLOW 0x07
#define CFG_EEPROM_PAGE_WRITE_BITS 4 /* The Catalyst CAT24WC08 has */
/* 16 byte page write mode using*/
- /* last 4 bits of the address */
+ /* last 4 bits of the address */
#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
#define CFG_EEPROM_PAGE_WRITE_ENABLE
/*-----------------------------------------------------------------------
* Cache Configuration
*/
-#define CFG_DCACHE_SIZE 16384 /* For IBM 405 CPUs, older 405 ppc's */
- /* have only 8kB, 16kB is save here */
+#define CFG_DCACHE_SIZE 16384 /* For IBM 405 CPUs, older 405 ppc's */
+ /* have only 8kB, 16kB is save here */
#define CFG_CACHELINE_SIZE 32 /* ... */
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
@@ -233,47 +233,47 @@
/*-----------------------------------------------------------------------
* External Bus Controller (EBC) Setup
*/
-#define FLASH0_BA 0xFF000000 /* FLASH 0 Base Address */
-#define FLASH1_BA 0xFE000000 /* FLASH 1 Base Address */
-#define CAN_BA 0xF0000000 /* CAN Base Address */
-#define RTC_BA 0xF0000500 /* RTC Base Address */
-#define CF_BA 0xF0100000 /* CompactFlash Base Address */
+#define FLASH0_BA 0xFF000000 /* FLASH 0 Base Address */
+#define FLASH1_BA 0xFE000000 /* FLASH 1 Base Address */
+#define CAN_BA 0xF0000000 /* CAN Base Address */
+#define RTC_BA 0xF0000500 /* RTC Base Address */
+#define CF_BA 0xF0100000 /* CompactFlash Base Address */
-/* Memory Bank 0 (Flash Bank 0) initialization */
-#define CFG_EBC_PB0AP 0x92015480
-#define CFG_EBC_PB0CR FLASH0_BA | 0x9A000 /* BAS=0xFF0,BS=16MB,BU=R/W,BW=16bit*/
+/* Memory Bank 0 (Flash Bank 0) initialization */
+#define CFG_EBC_PB0AP 0x92015480
+#define CFG_EBC_PB0CR FLASH0_BA | 0x9A000 /* BAS=0xFF0,BS=16MB,BU=R/W,BW=16bit*/
-/* Memory Bank 1 (Flash Bank 1) initialization */
-#define CFG_EBC_PB1AP 0x92015480
-#define CFG_EBC_PB1CR FLASH1_BA | 0x9A000 /* BAS=0xFE0,BS=16MB,BU=R/W,BW=16bit*/
+/* Memory Bank 1 (Flash Bank 1) initialization */
+#define CFG_EBC_PB1AP 0x92015480
+#define CFG_EBC_PB1CR FLASH1_BA | 0x9A000 /* BAS=0xFE0,BS=16MB,BU=R/W,BW=16bit*/
-/* Memory Bank 2 (CAN0, 1, RTC) initialization */
-#define CFG_EBC_PB2AP 0x03000040 /* TWT=6,TH=0,CSN=0,OEN=0,WBN=0,WBF=0 */
-#define CFG_EBC_PB2CR CAN_BA | 0x18000 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */
+/* Memory Bank 2 (CAN0, 1, RTC) initialization */
+#define CFG_EBC_PB2AP 0x03000040 /* TWT=6,TH=0,CSN=0,OEN=0,WBN=0,WBF=0 */
+#define CFG_EBC_PB2CR CAN_BA | 0x18000 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */
-/* Memory Bank 3 (CompactFlash IDE, FPGA internal) initialization */
-#define CFG_EBC_PB3AP 0x010059C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
-#define CFG_EBC_PB3CR CF_BA | 0x1A000 /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */
+/* Memory Bank 3 (CompactFlash IDE, FPGA internal) initialization */
+#define CFG_EBC_PB3AP 0x010059C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
+#define CFG_EBC_PB3CR CF_BA | 0x1A000 /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */
/*-----------------------------------------------------------------------
* FPGA stuff
*/
-#define CFG_FPGA_XC95XL 1 /* using Xilinx XC95XL CPLD */
-#define CFG_FPGA_MAX_SIZE 32*1024 /* 32kByte is enough for CPLD */
+#define CFG_FPGA_XC95XL 1 /* using Xilinx XC95XL CPLD */
+#define CFG_FPGA_MAX_SIZE 32*1024 /* 32kByte is enough for CPLD */
/* FPGA program pin configuration */
-#define CFG_FPGA_PRG 0x04000000 /* JTAG TMS pin (ppc output) */
-#define CFG_FPGA_CLK 0x02000000 /* JTAG TCK pin (ppc output) */
-#define CFG_FPGA_DATA 0x01000000 /* JTAG TDO->TDI data pin (ppc output) */
-#define CFG_FPGA_INIT 0x00010000 /* unused (ppc input) */
-#define CFG_FPGA_DONE 0x00008000 /* JTAG TDI->TDO pin (ppc input) */
+#define CFG_FPGA_PRG 0x04000000 /* JTAG TMS pin (ppc output) */
+#define CFG_FPGA_CLK 0x02000000 /* JTAG TCK pin (ppc output) */
+#define CFG_FPGA_DATA 0x01000000 /* JTAG TDO->TDI data pin (ppc output) */
+#define CFG_FPGA_INIT 0x00010000 /* unused (ppc input) */
+#define CFG_FPGA_DONE 0x00008000 /* JTAG TDI->TDO pin (ppc input) */
/*-----------------------------------------------------------------------
* Definitions for initial stack pointer and data area (in data cache)
*/
/* use on chip memory ( OCM ) for temperary stack until sdram is tested */
-#define CFG_TEMP_STACK_OCM 1
+#define CFG_TEMP_STACK_OCM 1
/* On Chip Memory location */
#define CFG_OCM_DATA_ADDR 0xF8000000
@@ -283,7 +283,7 @@
#define CFG_INIT_RAM_END CFG_OCM_DATA_SIZE /* End of used area in RAM */
#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
/*
* Internal Definitions
diff --git a/include/configs/PPChameleonEVB.h b/include/configs/PPChameleonEVB.h
index 50e8a15..cb76e3c 100644
--- a/include/configs/PPChameleonEVB.h
+++ b/include/configs/PPChameleonEVB.h
@@ -34,14 +34,14 @@
#define CONFIG_PPCHAMELEON_MODULE_BA 0 /* Basic Model */
#define CONFIG_PPCHAMELEON_MODULE_ME 1 /* Medium Model */
#define CONFIG_PPCHAMELEON_MODULE_HI 2 /* High-End Model */
-#ifndef CONFIG_PPCHAMELEON_MODULE_MODEL
-#define CONFIG_PPCHAMELEON_MODULE_MODEL CONFIG_PPCHAMELEON_MODULE_BA
+#ifndef CONFIG_PPCHAMELEON_MODULE_MODEL
+#define CONFIG_PPCHAMELEON_MODULE_MODEL CONFIG_PPCHAMELEON_MODULE_BA
#endif
/*
* Debug stuff
*/
-#undef __DEBUG_START_FROM_SRAM__
+#undef __DEBUG_START_FROM_SRAM__
#define __DISABLE_MACHINE_EXCEPTION__
#ifdef __DEBUG_START_FROM_SRAM__
@@ -54,13 +54,13 @@
*/
#define CONFIG_405EP 1 /* This is a PPC405 CPU */
-#define CONFIG_4xx 1 /* ...member of PPC4xx family */
-#define CONFIG_PPCHAMELEONEVB 1 /* ...on a PPChameleonEVB board */
+#define CONFIG_4xx 1 /* ...member of PPC4xx family */
+#define CONFIG_PPCHAMELEONEVB 1 /* ...on a PPChameleonEVB board */
-#define CONFIG_BOARD_PRE_INIT 1 /* call board_pre_init() */
-#define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */
+#define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */
+#define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */
-#define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */
+#define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */
#define CONFIG_BAUDRATE 115200
#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
@@ -70,7 +70,7 @@
/* Ethernet stuff */
#define CONFIG_ENV_OVERWRITE /* Let the user to change the Ethernet MAC addresses */
#define CONFIG_ETHADDR 00:50:c2:1e:af:fe
-#define CONFIG_ETH1ADDR 00:50:c2:1e:af:fd
+#define CONFIG_ETH1ADDR 00:50:c2:1e:af:fd
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
@@ -79,12 +79,12 @@
#undef CONFIG_EXT_PHY
#define CONFIG_MII 1 /* MII PHY management */
-#ifndef CONFIG_EXT_PHY
-#define CONFIG_PHY_ADDR 1 /* PHY address */
+#ifndef CONFIG_EXT_PHY
+#define CONFIG_PHY_ADDR 1 /* PHY address */
#else
-#define CONFIG_PHY_ADDR 2 /* PHY address */
+#define CONFIG_PHY_ADDR 2 /* PHY address */
#endif
-#define CONFIG_PHY_CLK_FREQ EMAC_STACR_CLK_66MHZ
+#define CONFIG_PHY_CLK_FREQ EMAC_STACR_CLK_66MHZ
#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \
CFG_CMD_DATE | \
@@ -101,12 +101,12 @@
/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
#include <cmd_confdefs.h>
-#undef CONFIG_WATCHDOG /* watchdog disabled */
+#undef CONFIG_WATCHDOG /* watchdog disabled */
-#define CONFIG_RTC_MC146818 /* DS1685 is MC146818 compatible*/
-#define CFG_RTC_REG_BASE_ADDR 0xF0000500 /* RTC Base Address */
+#define CONFIG_RTC_MC146818 /* DS1685 is MC146818 compatible*/
+#define CFG_RTC_REG_BASE_ADDR 0xF0000500 /* RTC Base Address */
-#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */
+#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */
/*
* Miscellaneous configurable options
@@ -116,38 +116,38 @@
#undef CFG_HUSH_PARSER /* use "hush" command parser */
#ifdef CFG_HUSH_PARSER
-#define CFG_PROMPT_HUSH_PS2 "> "
+#define CFG_PROMPT_HUSH_PS2 "> "
#endif
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
#endif
#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
#define CFG_MAXARGS 16 /* max number of command args */
#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_DEVICE_NULLDEV 1 /* include nulldev device */
+#define CFG_DEVICE_NULLDEV 1 /* include nulldev device */
-#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
+#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-#undef CFG_EXT_SERIAL_CLOCK /* no external serial clock used */
-#define CFG_IGNORE_405_UART_ERRATA_59 /* ignore ppc405gp errata #59 */
-#define CFG_BASE_BAUD 691200
+#undef CFG_EXT_SERIAL_CLOCK /* no external serial clock used */
+#define CFG_IGNORE_405_UART_ERRATA_59 /* ignore ppc405gp errata #59 */
+#define CFG_BASE_BAUD 691200
/* The following table includes the supported baudrates */
-#define CFG_BAUDRATE_TABLE \
+#define CFG_BAUDRATE_TABLE \
{ 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \
57600, 115200, 230400, 460800, 921600 }
#define CFG_LOAD_ADDR 0x100000 /* default load address */
#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
@@ -166,14 +166,14 @@
#define ADDR_PAGE 2
#define ADDR_COLUMN_PAGE 3
-#define NAND_ChipID_UNKNOWN 0x00
+#define NAND_ChipID_UNKNOWN 0x00
#define NAND_MAX_FLOORS 1
#define NAND_MAX_CHIPS 1
-#define CFG_NAND0_CE (0x80000000 >> 1) /* our CE is GPIO1 */
-#define CFG_NAND0_CLE (0x80000000 >> 2) /* our CLE is GPIO2 */
-#define CFG_NAND0_ALE (0x80000000 >> 3) /* our ALE is GPIO3 */
-#define CFG_NAND0_RDY (0x80000000 >> 4) /* our RDY is GPIO4 */
+#define CFG_NAND0_CE (0x80000000 >> 1) /* our CE is GPIO1 */
+#define CFG_NAND0_CLE (0x80000000 >> 2) /* our CLE is GPIO2 */
+#define CFG_NAND0_ALE (0x80000000 >> 3) /* our ALE is GPIO3 */
+#define CFG_NAND0_RDY (0x80000000 >> 4) /* our RDY is GPIO4 */
#define CFG_NAND1_CE (0x80000000 >> 14) /* our CE is GPIO14 */
#define CFG_NAND1_CLE (0x80000000 >> 15) /* our CLE is GPIO15 */
@@ -277,26 +277,26 @@
* PCI stuff
*-----------------------------------------------------------------------
*/
-#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */
-#define PCI_HOST_FORCE 1 /* configure as pci host */
-#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
+#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */
+#define PCI_HOST_FORCE 1 /* configure as pci host */
+#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
-#define CONFIG_PCI /* include pci support */
-#define CONFIG_PCI_HOST PCI_HOST_FORCE /* select pci host function */
-#undef CONFIG_PCI_PNP /* do pci plug-and-play */
- /* resource configuration */
+#define CONFIG_PCI /* include pci support */
+#define CONFIG_PCI_HOST PCI_HOST_FORCE /* select pci host function */
+#undef CONFIG_PCI_PNP /* do pci plug-and-play */
+ /* resource configuration */
-#define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */
+#define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */
-#define CFG_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */
-#define CFG_PCI_SUBSYS_DEVICEID 0x0405 /* PCI Device ID: CPCI-405 */
-#define CFG_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/
-#define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */
-#define CFG_PCI_PTM1MS 0xfc000001 /* 64MB, enable hard-wired to 1 */
-#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
-#define CFG_PCI_PTM2LA 0xffc00000 /* point to flash */
-#define CFG_PCI_PTM2MS 0xffc00001 /* 4MB, enable */
-#define CFG_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */
+#define CFG_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */
+#define CFG_PCI_SUBSYS_DEVICEID 0x0405 /* PCI Device ID: CPCI-405 */
+#define CFG_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/
+#define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */
+#define CFG_PCI_PTM1MS 0xfc000001 /* 64MB, enable hard-wired to 1 */
+#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
+#define CFG_PCI_PTM2LA 0xffc00000 /* point to flash */
+#define CFG_PCI_PTM2MS 0xffc00001 /* 4MB, enable */
+#define CFG_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */
/*-----------------------------------------------------------------------
* Start addresses for the final memory configuration
@@ -324,34 +324,34 @@
#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
#define CFG_FLASH_WRITE_TOUT 1000 /* Timeout for Flash Write (in ms) */
-#define CFG_FLASH_WORD_SIZE unsigned short /* flash word size (width) */
-#define CFG_FLASH_ADDR0 0x5555 /* 1st address for flash config cycles */
-#define CFG_FLASH_ADDR1 0x2AAA /* 2nd address for flash config cycles */
+#define CFG_FLASH_WORD_SIZE unsigned short /* flash word size (width) */
+#define CFG_FLASH_ADDR0 0x5555 /* 1st address for flash config cycles */
+#define CFG_FLASH_ADDR1 0x2AAA /* 2nd address for flash config cycles */
/*
* The following defines are added for buggy IOP480 byte interface.
* All other boards should use the standard values (CPCI405 etc.)
*/
-#define CFG_FLASH_READ0 0x0000 /* 0 is standard */
-#define CFG_FLASH_READ1 0x0001 /* 1 is standard */
-#define CFG_FLASH_READ2 0x0002 /* 2 is standard */
+#define CFG_FLASH_READ0 0x0000 /* 0 is standard */
+#define CFG_FLASH_READ1 0x0001 /* 1 is standard */
+#define CFG_FLASH_READ2 0x0002 /* 2 is standard */
-#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
+#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
#if 0 /* test-only */
-#define CFG_JFFS2_FIRST_BANK 0 /* use for JFFS2 */
-#define CFG_JFFS2_NUM_BANKS 1 /* ! second bank contains U-Boot */
+#define CFG_JFFS2_FIRST_BANK 0 /* use for JFFS2 */
+#define CFG_JFFS2_NUM_BANKS 1 /* ! second bank contains U-Boot */
#endif
/*-----------------------------------------------------------------------
* Environment Variable setup
*/
-#define CFG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
-#define CFG_ENV_OFFSET 0x100 /* environment starts at the beginning of the EEPROM */
-#define CFG_ENV_SIZE 0x700 /* 2048 bytes may be used for env vars*/
+#define CFG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
+#define CFG_ENV_OFFSET 0x100 /* environment starts at the beginning of the EEPROM */
+#define CFG_ENV_SIZE 0x700 /* 2048 bytes may be used for env vars*/
/* total size of a CAT24WC16 is 2048 bytes */
#define CFG_NVRAM_BASE_ADDR 0xF0000500 /* NVRAM base address */
-#define CFG_NVRAM_SIZE 242 /* NVRAM size */
+#define CFG_NVRAM_SIZE 242 /* NVRAM size */
/*-----------------------------------------------------------------------
* I2C EEPROM (CAT24WC16) for environment
@@ -361,20 +361,20 @@
#define CFG_I2C_SLAVE 0x7F
#define CFG_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC08 */
-#define CFG_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
-/* mask of address bits that overflow into the "EEPROM chip address" */
+#define CFG_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
+/* mask of address bits that overflow into the "EEPROM chip address" */
/*#define CFG_I2C_EEPROM_ADDR_OVERFLOW 0x07*/
#define CFG_EEPROM_PAGE_WRITE_BITS 4 /* The Catalyst CAT24WC08 has */
/* 16 byte page write mode using*/
- /* last 4 bits of the address */
+ /* last 4 bits of the address */
#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
#define CFG_EEPROM_PAGE_WRITE_ENABLE
/*-----------------------------------------------------------------------
* Cache Configuration
*/
-#define CFG_DCACHE_SIZE 16384 /* For IBM 405 CPUs, older 405 ppc's */
- /* have only 8kB, 16kB is save here */
+#define CFG_DCACHE_SIZE 16384 /* For IBM 405 CPUs, older 405 ppc's */
+ /* have only 8kB, 16kB is save here */
#define CFG_CACHELINE_SIZE 32 /* ... */
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
@@ -392,93 +392,93 @@
* External Bus Controller (EBC) Setup
*/
-/* Memory Bank 0 (Flash Bank 0, NOR-FLASH) initialization */
-#define CFG_EBC_PB0AP 0x92015480
-#define CFG_EBC_PB0CR 0xFFC5A000 /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
+/* Memory Bank 0 (Flash Bank 0, NOR-FLASH) initialization */
+#define CFG_EBC_PB0AP 0x92015480
+#define CFG_EBC_PB0CR 0xFFC5A000 /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
-/* Memory Bank 1 (External SRAM) initialization */
+/* Memory Bank 1 (External SRAM) initialization */
/* Since this must replace NOR Flash, we use the same settings for CS0 */
-#define CFG_EBC_PB1AP 0x92015480
-#define CFG_EBC_PB1CR 0xFF85A000 /* BAS=0xFF8,BS=4MB,BU=R/W,BW=8bit */
+#define CFG_EBC_PB1AP 0x92015480
+#define CFG_EBC_PB1CR 0xFF85A000 /* BAS=0xFF8,BS=4MB,BU=R/W,BW=8bit */
-/* Memory Bank 2 (Flash Bank 1, NAND-FLASH) initialization */
-#define CFG_EBC_PB2AP 0x92015480
-#define CFG_EBC_PB2CR 0xFF458000 /* BAS=0xFF4,BS=4MB,BU=R/W,BW=8bit */
+/* Memory Bank 2 (Flash Bank 1, NAND-FLASH) initialization */
+#define CFG_EBC_PB2AP 0x92015480
+#define CFG_EBC_PB2CR 0xFF458000 /* BAS=0xFF4,BS=4MB,BU=R/W,BW=8bit */
-/* Memory Bank 3 (Flash Bank 2, NAND-FLASH) initialization */
-#define CFG_EBC_PB3AP 0x92015480
-#define CFG_EBC_PB3CR 0xFF058000 /* BAS=0xFF0,BS=4MB,BU=R/W,BW=8bit */
+/* Memory Bank 3 (Flash Bank 2, NAND-FLASH) initialization */
+#define CFG_EBC_PB3AP 0x92015480
+#define CFG_EBC_PB3CR 0xFF058000 /* BAS=0xFF0,BS=4MB,BU=R/W,BW=8bit */
#if 0 /* Roese */
-/* Memory Bank 1 (Flash Bank 1, NAND-FLASH) initialization */
-#define CFG_EBC_PB1AP 0x92015480
-#define CFG_EBC_PB1CR 0xFF858000 /* BAS=0xFF8,BS=4MB,BU=R/W,BW=8bit */
+/* Memory Bank 1 (Flash Bank 1, NAND-FLASH) initialization */
+#define CFG_EBC_PB1AP 0x92015480
+#define CFG_EBC_PB1CR 0xFF858000 /* BAS=0xFF8,BS=4MB,BU=R/W,BW=8bit */
-/* Memory Bank 2 (CAN0, 1) initialization */
-#define CFG_EBC_PB2AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
-#define CFG_EBC_PB2CR 0xF0018000 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */
+/* Memory Bank 2 (CAN0, 1) initialization */
+#define CFG_EBC_PB2AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
+#define CFG_EBC_PB2CR 0xF0018000 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */
-/* Memory Bank 3 (CompactFlash IDE) initialization */
-#define CFG_EBC_PB3AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
-#define CFG_EBC_PB3CR 0xF011A000 /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */
+/* Memory Bank 3 (CompactFlash IDE) initialization */
+#define CFG_EBC_PB3AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
+#define CFG_EBC_PB3CR 0xF011A000 /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */
-/* Memory Bank 4 (NVRAM/RTC) initialization */
-#define CFG_EBC_PB4AP 0x01005280 /* TWT=2,WBN=1,WBF=1,TH=1,SOR=1 */
-#define CFG_EBC_PB4CR 0xF0218000 /* BAS=0xF02,BS=1MB,BU=R/W,BW=8bit */
+/* Memory Bank 4 (NVRAM/RTC) initialization */
+#define CFG_EBC_PB4AP 0x01005280 /* TWT=2,WBN=1,WBF=1,TH=1,SOR=1 */
+#define CFG_EBC_PB4CR 0xF0218000 /* BAS=0xF02,BS=1MB,BU=R/W,BW=8bit */
#endif
/*-----------------------------------------------------------------------
* FPGA stuff
*/
/* FPGA internal regs */
-#define CFG_FPGA_MODE 0x00
-#define CFG_FPGA_STATUS 0x02
-#define CFG_FPGA_TS 0x04
-#define CFG_FPGA_TS_LOW 0x06
-#define CFG_FPGA_TS_CAP0 0x10
-#define CFG_FPGA_TS_CAP0_LOW 0x12
-#define CFG_FPGA_TS_CAP1 0x14
-#define CFG_FPGA_TS_CAP1_LOW 0x16
-#define CFG_FPGA_TS_CAP2 0x18
-#define CFG_FPGA_TS_CAP2_LOW 0x1a
-#define CFG_FPGA_TS_CAP3 0x1c
-#define CFG_FPGA_TS_CAP3_LOW 0x1e
+#define CFG_FPGA_MODE 0x00
+#define CFG_FPGA_STATUS 0x02
+#define CFG_FPGA_TS 0x04
+#define CFG_FPGA_TS_LOW 0x06
+#define CFG_FPGA_TS_CAP0 0x10
+#define CFG_FPGA_TS_CAP0_LOW 0x12
+#define CFG_FPGA_TS_CAP1 0x14
+#define CFG_FPGA_TS_CAP1_LOW 0x16
+#define CFG_FPGA_TS_CAP2 0x18
+#define CFG_FPGA_TS_CAP2_LOW 0x1a
+#define CFG_FPGA_TS_CAP3 0x1c
+#define CFG_FPGA_TS_CAP3_LOW 0x1e
/* FPGA Mode Reg */
-#define CFG_FPGA_MODE_CF_RESET 0x0001
+#define CFG_FPGA_MODE_CF_RESET 0x0001
#define CFG_FPGA_MODE_TS_IRQ_ENABLE 0x0100
#define CFG_FPGA_MODE_TS_IRQ_CLEAR 0x1000
-#define CFG_FPGA_MODE_TS_CLEAR 0x2000
+#define CFG_FPGA_MODE_TS_CLEAR 0x2000
/* FPGA Status Reg */
-#define CFG_FPGA_STATUS_DIP0 0x0001
-#define CFG_FPGA_STATUS_DIP1 0x0002
-#define CFG_FPGA_STATUS_DIP2 0x0004
-#define CFG_FPGA_STATUS_FLASH 0x0008
-#define CFG_FPGA_STATUS_TS_IRQ 0x1000
+#define CFG_FPGA_STATUS_DIP0 0x0001
+#define CFG_FPGA_STATUS_DIP1 0x0002
+#define CFG_FPGA_STATUS_DIP2 0x0004
+#define CFG_FPGA_STATUS_FLASH 0x0008
+#define CFG_FPGA_STATUS_TS_IRQ 0x1000
-#define CFG_FPGA_SPARTAN2 1 /* using Xilinx Spartan 2 now */
-#define CFG_FPGA_MAX_SIZE 128*1024 /* 128kByte is enough for XC2S50E*/
+#define CFG_FPGA_SPARTAN2 1 /* using Xilinx Spartan 2 now */
+#define CFG_FPGA_MAX_SIZE 128*1024 /* 128kByte is enough for XC2S50E*/
/* FPGA program pin configuration */
-#define CFG_FPGA_PRG 0x04000000 /* FPGA program pin (ppc output) */
-#define CFG_FPGA_CLK 0x02000000 /* FPGA clk pin (ppc output) */
-#define CFG_FPGA_DATA 0x01000000 /* FPGA data pin (ppc output) */
-#define CFG_FPGA_INIT 0x00010000 /* FPGA init pin (ppc input) */
-#define CFG_FPGA_DONE 0x00008000 /* FPGA done pin (ppc input) */
+#define CFG_FPGA_PRG 0x04000000 /* FPGA program pin (ppc output) */
+#define CFG_FPGA_CLK 0x02000000 /* FPGA clk pin (ppc output) */
+#define CFG_FPGA_DATA 0x01000000 /* FPGA data pin (ppc output) */
+#define CFG_FPGA_INIT 0x00010000 /* FPGA init pin (ppc input) */
+#define CFG_FPGA_DONE 0x00008000 /* FPGA done pin (ppc input) */
/*-----------------------------------------------------------------------
* Definitions for initial stack pointer and data area (in data cache)
*/
#if 0 /* test-only */
-#define CFG_INIT_DCACHE_CS 4 /* use cs # 4 for data cache memory */
+#define CFG_INIT_DCACHE_CS 4 /* use cs # 4 for data cache memory */
-#define CFG_INIT_RAM_ADDR 0x40000000 /* use data cache */
-#define CFG_INIT_RAM_END 0x2000 /* End of used area in RAM */
+#define CFG_INIT_RAM_ADDR 0x40000000 /* use data cache */
+#define CFG_INIT_RAM_END 0x2000 /* End of used area in RAM */
#else
/* use on chip memory ( OCM ) for temperary stack until sdram is tested */
-#define CFG_TEMP_STACK_OCM 1
+#define CFG_TEMP_STACK_OCM 1
/* On Chip Memory location */
#define CFG_OCM_DATA_ADDR 0xF8000000
@@ -489,29 +489,29 @@
#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
/*-----------------------------------------------------------------------
* Definitions for GPIO setup (PPC405EP specific)
*
- * GPIO0[0] - External Bus Controller BLAST output
- * GPIO0[1-9] - Instruction trace outputs -> GPIO
+ * GPIO0[0] - External Bus Controller BLAST output
+ * GPIO0[1-9] - Instruction trace outputs -> GPIO
* GPIO0[10-13] - External Bus Controller CS_1 - CS_4 outputs
* GPIO0[14-16] - External Bus Controller ABUS3-ABUS5 outputs -> GPIO
* GPIO0[17-23] - External Interrupts IRQ0 - IRQ6 inputs
* GPIO0[24-27] - UART0 control signal inputs/outputs
* GPIO0[28-29] - UART1 data signal input/output
- * GPIO0[30] - EMAC0 input
- * GPIO0[31] - EMAC1 reject packet as output
+ * GPIO0[30] - EMAC0 input
+ * GPIO0[31] - EMAC1 reject packet as output
*/
-#define CFG_GPIO0_OSRH 0x40000550
-#define CFG_GPIO0_OSRL 0x00000110
-#define CFG_GPIO0_ISR1H 0x00000000
-/*#define CFG_GPIO0_ISR1L 0x15555445*/
-#define CFG_GPIO0_ISR1L 0x15555444
-#define CFG_GPIO0_TSRH 0x00000000
-#define CFG_GPIO0_TSRL 0x00000000
-#define CFG_GPIO0_TCR 0xF7FF8014
+#define CFG_GPIO0_OSRH 0x40000550
+#define CFG_GPIO0_OSRL 0x00000110
+#define CFG_GPIO0_ISR1H 0x00000000
+/*#define CFG_GPIO0_ISR1L 0x15555445*/
+#define CFG_GPIO0_ISR1L 0x15555444
+#define CFG_GPIO0_TSRH 0x00000000
+#define CFG_GPIO0_TSRL 0x00000000
+#define CFG_GPIO0_TCR 0xF7FF8014
/*
* Internal Definitions
@@ -532,163 +532,163 @@
!-----------------------------------------------------------------------
! Defines for entry options.
! Note: Because the 405EP SDRAM controller does not support ECC, ECC DIMMs that
-! are plugged in the board will be utilized as non-ECC DIMMs.
+! are plugged in the board will be utilized as non-ECC DIMMs.
!-----------------------------------------------------------------------
*/
-#undef AUTO_MEMORY_CONFIG
-#define DIMM_READ_ADDR 0xAB
-#define DIMM_WRITE_ADDR 0xAA
+#undef AUTO_MEMORY_CONFIG
+#define DIMM_READ_ADDR 0xAB
+#define DIMM_WRITE_ADDR 0xAA
-#define CPC0_PLLMR0 (CNTRL_DCR_BASE+0x0) /* PLL mode 0 register */
+#define CPC0_PLLMR0 (CNTRL_DCR_BASE+0x0) /* PLL mode 0 register */
#define CPC0_BOOT (CNTRL_DCR_BASE+0x1) /* Chip Clock Status register */
-#define CPC0_CR1 (CNTRL_DCR_BASE+0x2) /* Chip Control 1 register */
+#define CPC0_CR1 (CNTRL_DCR_BASE+0x2) /* Chip Control 1 register */
#define CPC0_EPRCSR (CNTRL_DCR_BASE+0x3) /* EMAC PHY Rcv Clk Src register*/
-#define CPC0_PLLMR1 (CNTRL_DCR_BASE+0x4) /* PLL mode 1 register */
-#define CPC0_UCR (CNTRL_DCR_BASE+0x5) /* UART Control register */
-#define CPC0_SRR (CNTRL_DCR_BASE+0x6) /* Soft Reset register */
-#define CPC0_JTAGID (CNTRL_DCR_BASE+0x7) /* JTAG ID register */
-#define CPC0_SPARE (CNTRL_DCR_BASE+0x8) /* Spare DCR */
-#define CPC0_PCI (CNTRL_DCR_BASE+0x9) /* PCI Control register */
+#define CPC0_PLLMR1 (CNTRL_DCR_BASE+0x4) /* PLL mode 1 register */
+#define CPC0_UCR (CNTRL_DCR_BASE+0x5) /* UART Control register */
+#define CPC0_SRR (CNTRL_DCR_BASE+0x6) /* Soft Reset register */
+#define CPC0_JTAGID (CNTRL_DCR_BASE+0x7) /* JTAG ID register */
+#define CPC0_SPARE (CNTRL_DCR_BASE+0x8) /* Spare DCR */
+#define CPC0_PCI (CNTRL_DCR_BASE+0x9) /* PCI Control register */
/* Defines for CPC0_PLLMR1 Register fields */
-#define PLL_ACTIVE 0x80000000
-#define CPC0_PLLMR1_SSCS 0x80000000
-#define PLL_RESET 0x40000000
-#define CPC0_PLLMR1_PLLR 0x40000000
+#define PLL_ACTIVE 0x80000000
+#define CPC0_PLLMR1_SSCS 0x80000000
+#define PLL_RESET 0x40000000
+#define CPC0_PLLMR1_PLLR 0x40000000
/* Feedback multiplier */
-#define PLL_FBKDIV 0x00F00000
-#define CPC0_PLLMR1_FBDV 0x00F00000
-#define PLL_FBKDIV_16 0x00000000
-#define PLL_FBKDIV_1 0x00100000
-#define PLL_FBKDIV_2 0x00200000
-#define PLL_FBKDIV_3 0x00300000
-#define PLL_FBKDIV_4 0x00400000
-#define PLL_FBKDIV_5 0x00500000
-#define PLL_FBKDIV_6 0x00600000
-#define PLL_FBKDIV_7 0x00700000
-#define PLL_FBKDIV_8 0x00800000
-#define PLL_FBKDIV_9 0x00900000
-#define PLL_FBKDIV_10 0x00A00000
-#define PLL_FBKDIV_11 0x00B00000
-#define PLL_FBKDIV_12 0x00C00000
-#define PLL_FBKDIV_13 0x00D00000
-#define PLL_FBKDIV_14 0x00E00000
-#define PLL_FBKDIV_15 0x00F00000
+#define PLL_FBKDIV 0x00F00000
+#define CPC0_PLLMR1_FBDV 0x00F00000
+#define PLL_FBKDIV_16 0x00000000
+#define PLL_FBKDIV_1 0x00100000
+#define PLL_FBKDIV_2 0x00200000
+#define PLL_FBKDIV_3 0x00300000
+#define PLL_FBKDIV_4 0x00400000
+#define PLL_FBKDIV_5 0x00500000
+#define PLL_FBKDIV_6 0x00600000
+#define PLL_FBKDIV_7 0x00700000
+#define PLL_FBKDIV_8 0x00800000
+#define PLL_FBKDIV_9 0x00900000
+#define PLL_FBKDIV_10 0x00A00000
+#define PLL_FBKDIV_11 0x00B00000
+#define PLL_FBKDIV_12 0x00C00000
+#define PLL_FBKDIV_13 0x00D00000
+#define PLL_FBKDIV_14 0x00E00000
+#define PLL_FBKDIV_15 0x00F00000
/* Forward A divisor */
-#define PLL_FWDDIVA 0x00070000
-#define CPC0_PLLMR1_FWDVA 0x00070000
-#define PLL_FWDDIVA_8 0x00000000
-#define PLL_FWDDIVA_7 0x00010000
-#define PLL_FWDDIVA_6 0x00020000
-#define PLL_FWDDIVA_5 0x00030000
-#define PLL_FWDDIVA_4 0x00040000
-#define PLL_FWDDIVA_3 0x00050000
-#define PLL_FWDDIVA_2 0x00060000
-#define PLL_FWDDIVA_1 0x00070000
+#define PLL_FWDDIVA 0x00070000
+#define CPC0_PLLMR1_FWDVA 0x00070000
+#define PLL_FWDDIVA_8 0x00000000
+#define PLL_FWDDIVA_7 0x00010000
+#define PLL_FWDDIVA_6 0x00020000
+#define PLL_FWDDIVA_5 0x00030000
+#define PLL_FWDDIVA_4 0x00040000
+#define PLL_FWDDIVA_3 0x00050000
+#define PLL_FWDDIVA_2 0x00060000
+#define PLL_FWDDIVA_1 0x00070000
/* Forward B divisor */
-#define PLL_FWDDIVB 0x00007000
-#define CPC0_PLLMR1_FWDVB 0x00007000
-#define PLL_FWDDIVB_8 0x00000000
-#define PLL_FWDDIVB_7 0x00001000
-#define PLL_FWDDIVB_6 0x00002000
-#define PLL_FWDDIVB_5 0x00003000
-#define PLL_FWDDIVB_4 0x00004000
-#define PLL_FWDDIVB_3 0x00005000
-#define PLL_FWDDIVB_2 0x00006000
-#define PLL_FWDDIVB_1 0x00007000
+#define PLL_FWDDIVB 0x00007000
+#define CPC0_PLLMR1_FWDVB 0x00007000
+#define PLL_FWDDIVB_8 0x00000000
+#define PLL_FWDDIVB_7 0x00001000
+#define PLL_FWDDIVB_6 0x00002000
+#define PLL_FWDDIVB_5 0x00003000
+#define PLL_FWDDIVB_4 0x00004000
+#define PLL_FWDDIVB_3 0x00005000
+#define PLL_FWDDIVB_2 0x00006000
+#define PLL_FWDDIVB_1 0x00007000
/* PLL tune bits */
-#define PLL_TUNE_MASK 0x000003FF
-#define PLL_TUNE_2_M_3 0x00000133 /* 2 <= M <= 3 */
-#define PLL_TUNE_4_M_6 0x00000134 /* 3 < M <= 6 */
-#define PLL_TUNE_7_M_10 0x00000138 /* 6 < M <= 10 */
-#define PLL_TUNE_11_M_14 0x0000013C /* 10 < M <= 14 */
-#define PLL_TUNE_15_M_40 0x0000023E /* 14 < M <= 40 */
-#define PLL_TUNE_VCO_LOW 0x00000000 /* 500MHz <= VCO <= 800MHz */
-#define PLL_TUNE_VCO_HI 0x00000080 /* 800MHz < VCO <= 1000MHz */
+#define PLL_TUNE_MASK 0x000003FF
+#define PLL_TUNE_2_M_3 0x00000133 /* 2 <= M <= 3 */
+#define PLL_TUNE_4_M_6 0x00000134 /* 3 < M <= 6 */
+#define PLL_TUNE_7_M_10 0x00000138 /* 6 < M <= 10 */
+#define PLL_TUNE_11_M_14 0x0000013C /* 10 < M <= 14 */
+#define PLL_TUNE_15_M_40 0x0000023E /* 14 < M <= 40 */
+#define PLL_TUNE_VCO_LOW 0x00000000 /* 500MHz <= VCO <= 800MHz */
+#define PLL_TUNE_VCO_HI 0x00000080 /* 800MHz < VCO <= 1000MHz */
/* Defines for CPC0_PLLMR0 Register fields */
/* CPU divisor */
-#define PLL_CPUDIV 0x00300000
-#define CPC0_PLLMR0_CCDV 0x00300000
-#define PLL_CPUDIV_1 0x00000000
-#define PLL_CPUDIV_2 0x00100000
-#define PLL_CPUDIV_3 0x00200000
-#define PLL_CPUDIV_4 0x00300000
+#define PLL_CPUDIV 0x00300000
+#define CPC0_PLLMR0_CCDV 0x00300000
+#define PLL_CPUDIV_1 0x00000000
+#define PLL_CPUDIV_2 0x00100000
+#define PLL_CPUDIV_3 0x00200000
+#define PLL_CPUDIV_4 0x00300000
/* PLB divisor */
-#define PLL_PLBDIV 0x00030000
-#define CPC0_PLLMR0_CBDV 0x00030000
-#define PLL_PLBDIV_1 0x00000000
-#define PLL_PLBDIV_2 0x00010000
-#define PLL_PLBDIV_3 0x00020000
-#define PLL_PLBDIV_4 0x00030000
+#define PLL_PLBDIV 0x00030000
+#define CPC0_PLLMR0_CBDV 0x00030000
+#define PLL_PLBDIV_1 0x00000000
+#define PLL_PLBDIV_2 0x00010000
+#define PLL_PLBDIV_3 0x00020000
+#define PLL_PLBDIV_4 0x00030000
/* OPB divisor */
-#define PLL_OPBDIV 0x00003000
-#define CPC0_PLLMR0_OPDV 0x00003000
-#define PLL_OPBDIV_1 0x00000000
-#define PLL_OPBDIV_2 0x00001000
-#define PLL_OPBDIV_3 0x00002000
-#define PLL_OPBDIV_4 0x00003000
+#define PLL_OPBDIV 0x00003000
+#define CPC0_PLLMR0_OPDV 0x00003000
+#define PLL_OPBDIV_1 0x00000000
+#define PLL_OPBDIV_2 0x00001000
+#define PLL_OPBDIV_3 0x00002000
+#define PLL_OPBDIV_4 0x00003000
/* EBC divisor */
-#define PLL_EXTBUSDIV 0x00000300
-#define CPC0_PLLMR0_EPDV 0x00000300
-#define PLL_EXTBUSDIV_2 0x00000000
-#define PLL_EXTBUSDIV_3 0x00000100
-#define PLL_EXTBUSDIV_4 0x00000200
-#define PLL_EXTBUSDIV_5 0x00000300
+#define PLL_EXTBUSDIV 0x00000300
+#define CPC0_PLLMR0_EPDV 0x00000300
+#define PLL_EXTBUSDIV_2 0x00000000
+#define PLL_EXTBUSDIV_3 0x00000100
+#define PLL_EXTBUSDIV_4 0x00000200
+#define PLL_EXTBUSDIV_5 0x00000300
/* MAL divisor */
-#define PLL_MALDIV 0x00000030
-#define CPC0_PLLMR0_MPDV 0x00000030
-#define PLL_MALDIV_1 0x00000000
-#define PLL_MALDIV_2 0x00000010
-#define PLL_MALDIV_3 0x00000020
-#define PLL_MALDIV_4 0x00000030
+#define PLL_MALDIV 0x00000030
+#define CPC0_PLLMR0_MPDV 0x00000030
+#define PLL_MALDIV_1 0x00000000
+#define PLL_MALDIV_2 0x00000010
+#define PLL_MALDIV_3 0x00000020
+#define PLL_MALDIV_4 0x00000030
/* PCI divisor */
-#define PLL_PCIDIV 0x00000003
-#define CPC0_PLLMR0_PPFD 0x00000003
-#define PLL_PCIDIV_1 0x00000000
-#define PLL_PCIDIV_2 0x00000001
-#define PLL_PCIDIV_3 0x00000002
-#define PLL_PCIDIV_4 0x00000003
+#define PLL_PCIDIV 0x00000003
+#define CPC0_PLLMR0_PPFD 0x00000003
+#define PLL_PCIDIV_1 0x00000000
+#define PLL_PCIDIV_2 0x00000001
+#define PLL_PCIDIV_3 0x00000002
+#define PLL_PCIDIV_4 0x00000003
/* CPU - PLB/SDRAM - EBC - OPB - PCI (assuming a 33.3MHz input clock to the 405EP) */
-#define PLLMR0_133_133_33_66_33 (PLL_CPUDIV_1 | PLL_PLBDIV_1 | \
- PLL_OPBDIV_2 | PLL_EXTBUSDIV_4 | \
+#define PLLMR0_133_133_33_66_33 (PLL_CPUDIV_1 | PLL_PLBDIV_1 | \
+ PLL_OPBDIV_2 | PLL_EXTBUSDIV_4 | \
PLL_MALDIV_1 | PLL_PCIDIV_4)
-#define PLLMR1_133_133_33_66_33 (PLL_FBKDIV_4 | \
+#define PLLMR1_133_133_33_66_33 (PLL_FBKDIV_4 | \
PLL_FWDDIVA_6 | PLL_FWDDIVB_6 | \
PLL_TUNE_15_M_40 | PLL_TUNE_VCO_LOW)
#define PLLMR0_200_100_50_33 (PLL_CPUDIV_1 | PLL_PLBDIV_2 | \
- PLL_OPBDIV_2 | PLL_EXTBUSDIV_3 | \
+ PLL_OPBDIV_2 | PLL_EXTBUSDIV_3 | \
PLL_MALDIV_1 | PLL_PCIDIV_4)
#define PLLMR1_200_100_50_33 (PLL_FBKDIV_6 | \
PLL_FWDDIVA_4 | PLL_FWDDIVB_4 | \
PLL_TUNE_15_M_40 | PLL_TUNE_VCO_LOW)
-#define PLLMR0_266_133_33_66_33 (PLL_CPUDIV_1 | PLL_PLBDIV_2 | \
- PLL_OPBDIV_2 | PLL_EXTBUSDIV_4 | \
+#define PLLMR0_266_133_33_66_33 (PLL_CPUDIV_1 | PLL_PLBDIV_2 | \
+ PLL_OPBDIV_2 | PLL_EXTBUSDIV_4 | \
PLL_MALDIV_1 | PLL_PCIDIV_4)
#define PLLMR1_266_133_33_66_33 (PLL_FBKDIV_8 | \
PLL_FWDDIVA_3 | PLL_FWDDIVB_3 | \
PLL_TUNE_15_M_40 | PLL_TUNE_VCO_LOW)
-#define PLLMR0_333_111_37_55_55 (PLL_CPUDIV_1 | PLL_PLBDIV_3 | \
- PLL_OPBDIV_2 | PLL_EXTBUSDIV_3 | \
+#define PLLMR0_333_111_37_55_55 (PLL_CPUDIV_1 | PLL_PLBDIV_3 | \
+ PLL_OPBDIV_2 | PLL_EXTBUSDIV_3 | \
PLL_MALDIV_1 | PLL_PCIDIV_2)
-#define PLLMR1_333_111_37_55_55 (PLL_FBKDIV_10 | \
+#define PLLMR1_333_111_37_55_55 (PLL_FBKDIV_10 | \
PLL_FWDDIVA_3 | PLL_FWDDIVB_3 | \
PLL_TUNE_15_M_40 | PLL_TUNE_VCO_HI)
#if (CONFIG_PPCHAMELEON_MODULE_MODEL == CONFIG_PPCHAMELEON_MODULE_HI)
/* Model HI */
-#define PLLMR0_DEFAULT PLLMR0_333_111_37_55_55
-#define PLLMR1_DEFAULT PLLMR1_333_111_37_55_55
+#define PLLMR0_DEFAULT PLLMR0_333_111_37_55_55
+#define PLLMR1_DEFAULT PLLMR1_333_111_37_55_55
/* Model ME */
#elif (CONFIG_PPCHAMELEON_MODULE_MODEL == CONFIG_PPCHAMELEON_MODULE_ME)
-#define PLLMR0_DEFAULT PLLMR0_266_133_33_66_33
-#define PLLMR1_DEFAULT PLLMR1_266_133_33_66_33
+#define PLLMR0_DEFAULT PLLMR0_266_133_33_66_33
+#define PLLMR1_DEFAULT PLLMR1_266_133_33_66_33
#else
/* Model BA (default) */
-#define PLLMR0_DEFAULT PLLMR0_133_133_33_66_33
-#define PLLMR1_DEFAULT PLLMR1_133_133_33_66_33
+#define PLLMR0_DEFAULT PLLMR0_133_133_33_66_33
+#define PLLMR1_DEFAULT PLLMR1_133_133_33_66_33
#endif
diff --git a/include/configs/RPXsuper.h b/include/configs/RPXsuper.h
index 0abff11..cdf716c 100644
--- a/include/configs/RPXsuper.h
+++ b/include/configs/RPXsuper.h
@@ -174,7 +174,7 @@
#define CONFIG_MPC8260 1 /* This is an MPC8260 CPU */
#define CONFIG_RPXSUPER 1 /* on an Embedded Planet RPX Super Board */
-#define CONFIG_BOARD_PRE_INIT 1 /* Call board_pre_init */
+#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
#include <cmd_confdefs.h>
diff --git a/include/configs/VOH405.h b/include/configs/VOH405.h
index 13a0105..b64611b 100644
--- a/include/configs/VOH405.h
+++ b/include/configs/VOH405.h
@@ -34,13 +34,13 @@
*/
#define CONFIG_405EP 1 /* This is a PPC405 CPU */
-#define CONFIG_4xx 1 /* ...member of PPC4xx family */
-#define CONFIG_VOH405 1 /* ...on a VOH405 board */
+#define CONFIG_4xx 1 /* ...member of PPC4xx family */
+#define CONFIG_VOH405 1 /* ...on a VOH405 board */
-#define CONFIG_BOARD_PRE_INIT 1 /* call board_pre_init() */
-#define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */
+#define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */
+#define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */
-#define CONFIG_SYS_CLK_FREQ 33333334 /* external frequency to pll */
+#define CONFIG_SYS_CLK_FREQ 33333334 /* external frequency to pll */
#define CONFIG_BAUDRATE 9600
#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */
@@ -60,7 +60,7 @@
#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
#define CONFIG_MII 1 /* MII PHY management */
-#define CONFIG_PHY_ADDR 0 /* PHY address */
+#define CONFIG_PHY_ADDR 0 /* PHY address */
#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \
CFG_CMD_DHCP | \
@@ -73,7 +73,7 @@
CFG_CMD_I2C | \
CFG_CMD_MII | \
CFG_CMD_PING | \
- CFG_CMD_EEPROM )
+ CFG_CMD_EEPROM )
#define CONFIG_MAC_PARTITION
#define CONFIG_DOS_PARTITION
@@ -81,12 +81,12 @@
/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
#include <cmd_confdefs.h>
-#undef CONFIG_WATCHDOG /* watchdog disabled */
+#undef CONFIG_WATCHDOG /* watchdog disabled */
-#define CONFIG_RTC_MC146818 /* DS1685 is MC146818 compatible*/
-#define CFG_RTC_REG_BASE_ADDR 0xF0000500 /* RTC Base Address */
+#define CONFIG_RTC_MC146818 /* DS1685 is MC146818 compatible*/
+#define CFG_RTC_REG_BASE_ADDR 0xF0000500 /* RTC Base Address */
-#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */
+#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */
/*
* Miscellaneous configurable options
@@ -96,45 +96,45 @@
#undef CFG_HUSH_PARSER /* use "hush" command parser */
#ifdef CFG_HUSH_PARSER
-#define CFG_PROMPT_HUSH_PS2 "> "
+#define CFG_PROMPT_HUSH_PS2 "> "
#endif
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
#endif
#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
#define CFG_MAXARGS 16 /* max number of command args */
#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_DEVICE_NULLDEV 1 /* include nulldev device */
+#define CFG_DEVICE_NULLDEV 1 /* include nulldev device */
-#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
+#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-#undef CFG_EXT_SERIAL_CLOCK /* no external serial clock used */
-#define CFG_IGNORE_405_UART_ERRATA_59 /* ignore ppc405gp errata #59 */
-#define CFG_BASE_BAUD 691200
-#undef CONFIG_UART1_CONSOLE /* define for uart1 as console */
+#undef CFG_EXT_SERIAL_CLOCK /* no external serial clock used */
+#define CFG_IGNORE_405_UART_ERRATA_59 /* ignore ppc405gp errata #59 */
+#define CFG_BASE_BAUD 691200
+#undef CONFIG_UART1_CONSOLE /* define for uart1 as console */
/* The following table includes the supported baudrates */
-#define CFG_BAUDRATE_TABLE \
+#define CFG_BAUDRATE_TABLE \
{ 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \
57600, 115200, 230400, 460800, 921600 }
#define CFG_LOAD_ADDR 0x100000 /* default load address */
#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
+#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
-#define CFG_RX_ETH_BUFFER 16 /* use 16 rx buffer on 405 emac */
+#define CFG_RX_ETH_BUFFER 16 /* use 16 rx buffer on 405 emac */
/*-----------------------------------------------------------------------
* NAND-FLASH stuff
@@ -147,14 +147,14 @@
#define ADDR_PAGE 2
#define ADDR_COLUMN_PAGE 3
-#define NAND_ChipID_UNKNOWN 0x00
+#define NAND_ChipID_UNKNOWN 0x00
#define NAND_MAX_FLOORS 1
#define NAND_MAX_CHIPS 1
-#define CFG_NAND_CE (0x80000000 >> 1) /* our CE is GPIO1 */
-#define CFG_NAND_CLE (0x80000000 >> 2) /* our CLE is GPIO2 */
-#define CFG_NAND_ALE (0x80000000 >> 3) /* our ALE is GPIO3 */
-#define CFG_NAND_RDY (0x80000000 >> 4) /* our RDY is GPIO4 */
+#define CFG_NAND_CE (0x80000000 >> 1) /* our CE is GPIO1 */
+#define CFG_NAND_CLE (0x80000000 >> 2) /* our CLE is GPIO2 */
+#define CFG_NAND_ALE (0x80000000 >> 3) /* our ALE is GPIO3 */
+#define CFG_NAND_RDY (0x80000000 >> 4) /* our RDY is GPIO4 */
#define NAND_DISABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CE);} while(0)
#define NAND_ENABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CE);} while(0)
@@ -173,46 +173,46 @@
* PCI stuff
*-----------------------------------------------------------------------
*/
-#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */
-#define PCI_HOST_FORCE 1 /* configure as pci host */
-#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
+#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */
+#define PCI_HOST_FORCE 1 /* configure as pci host */
+#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
-#define CONFIG_PCI /* include pci support */
-#define CONFIG_PCI_HOST PCI_HOST_HOST /* select pci host function */
-#define CONFIG_PCI_PNP /* do pci plug-and-play */
- /* resource configuration */
+#define CONFIG_PCI /* include pci support */
+#define CONFIG_PCI_HOST PCI_HOST_HOST /* select pci host function */
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
+ /* resource configuration */
-#define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */
+#define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */
-#define CFG_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */
-#define CFG_PCI_SUBSYS_DEVICEID 0x0405 /* PCI Device ID: CPCI-405 */
-#define CFG_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/
-#define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */
-#define CFG_PCI_PTM1MS 0xfc000001 /* 64MB, enable hard-wired to 1 */
-#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
-#define CFG_PCI_PTM2LA 0xffc00000 /* point to flash */
-#define CFG_PCI_PTM2MS 0xffc00001 /* 4MB, enable */
-#define CFG_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */
+#define CFG_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */
+#define CFG_PCI_SUBSYS_DEVICEID 0x0405 /* PCI Device ID: CPCI-405 */
+#define CFG_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/
+#define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */
+#define CFG_PCI_PTM1MS 0xfc000001 /* 64MB, enable hard-wired to 1 */
+#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
+#define CFG_PCI_PTM2LA 0xffc00000 /* point to flash */
+#define CFG_PCI_PTM2MS 0xffc00001 /* 4MB, enable */
+#define CFG_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */
/*-----------------------------------------------------------------------
* IDE/ATA stuff
*-----------------------------------------------------------------------
*/
-#undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */
-#undef CONFIG_IDE_LED /* no led for ide supported */
+#undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */
+#undef CONFIG_IDE_LED /* no led for ide supported */
#define CONFIG_IDE_RESET 1 /* reset for ide supported */
-#define CFG_IDE_MAXBUS 2 /* max. 2 IDE busses */
-#define CFG_IDE_MAXDEVICE (CFG_IDE_MAXBUS*2) /* max. 2 drives per IDE bus */
+#define CFG_IDE_MAXBUS 2 /* max. 2 IDE busses */
+#define CFG_IDE_MAXDEVICE (CFG_IDE_MAXBUS*2) /* max. 2 drives per IDE bus */
-#define CONFIG_ATAPI 1 /* ATAPI for Travelstar */
+#define CONFIG_ATAPI 1 /* ATAPI for Travelstar */
-#define CFG_ATA_BASE_ADDR 0xF0100000
-#define CFG_ATA_IDE0_OFFSET 0x0000
-#define CFG_ATA_IDE1_OFFSET 0x0010
+#define CFG_ATA_BASE_ADDR 0xF0100000
+#define CFG_ATA_IDE0_OFFSET 0x0000
+#define CFG_ATA_IDE1_OFFSET 0x0010
#define CFG_ATA_DATA_OFFSET 0x0000 /* Offset for data I/O */
-#define CFG_ATA_REG_OFFSET 0x0000 /* Offset for normal register accesses */
+#define CFG_ATA_REG_OFFSET 0x0000 /* Offset for normal register accesses */
#define CFG_ATA_ALT_OFFSET 0x0000 /* Offset for alternate registers */
/*
@@ -232,22 +232,22 @@
#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
#define CFG_FLASH_WRITE_TOUT 1000 /* Timeout for Flash Write (in ms) */
-#define CFG_FLASH_WORD_SIZE unsigned short /* flash word size (width) */
-#define CFG_FLASH_ADDR0 0x5555 /* 1st address for flash config cycles */
-#define CFG_FLASH_ADDR1 0x2AAA /* 2nd address for flash config cycles */
+#define CFG_FLASH_WORD_SIZE unsigned short /* flash word size (width) */
+#define CFG_FLASH_ADDR0 0x5555 /* 1st address for flash config cycles */
+#define CFG_FLASH_ADDR1 0x2AAA /* 2nd address for flash config cycles */
/*
* The following defines are added for buggy IOP480 byte interface.
* All other boards should use the standard values (CPCI405 etc.)
*/
-#define CFG_FLASH_READ0 0x0000 /* 0 is standard */
-#define CFG_FLASH_READ1 0x0001 /* 1 is standard */
-#define CFG_FLASH_READ2 0x0002 /* 2 is standard */
+#define CFG_FLASH_READ0 0x0000 /* 0 is standard */
+#define CFG_FLASH_READ1 0x0001 /* 1 is standard */
+#define CFG_FLASH_READ2 0x0002 /* 2 is standard */
-#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
+#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
#if 0 /* test-only */
-#define CFG_JFFS2_FIRST_BANK 0 /* use for JFFS2 */
-#define CFG_JFFS2_NUM_BANKS 1 /* ! second bank contains U-Boot */
+#define CFG_JFFS2_FIRST_BANK 0 /* use for JFFS2 */
+#define CFG_JFFS2_NUM_BANKS 1 /* ! second bank contains U-Boot */
#endif
/*-----------------------------------------------------------------------
@@ -270,13 +270,13 @@
/*-----------------------------------------------------------------------
* Environment Variable setup
*/
-#define CFG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
-#define CFG_ENV_OFFSET 0x100 /* environment starts at the beginning of the EEPROM */
-#define CFG_ENV_SIZE 0x700 /* 2048 bytes may be used for env vars*/
+#define CFG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
+#define CFG_ENV_OFFSET 0x100 /* environment starts at the beginning of the EEPROM */
+#define CFG_ENV_SIZE 0x700 /* 2048 bytes may be used for env vars*/
/* total size of a CAT24WC16 is 2048 bytes */
#define CFG_NVRAM_BASE_ADDR 0xF0000500 /* NVRAM base address */
-#define CFG_NVRAM_SIZE 242 /* NVRAM size */
+#define CFG_NVRAM_SIZE 242 /* NVRAM size */
/*-----------------------------------------------------------------------
* I2C EEPROM (CAT24WC16) for environment
@@ -288,20 +288,20 @@
#define CFG_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT24WC08 */
#if 0 /* test-only */
/* CAT24WC08/16... */
-#define CFG_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
-/* mask of address bits that overflow into the "EEPROM chip address" */
+#define CFG_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
+/* mask of address bits that overflow into the "EEPROM chip address" */
#define CFG_I2C_EEPROM_ADDR_OVERFLOW 0x07
#define CFG_EEPROM_PAGE_WRITE_BITS 4 /* The Catalyst CAT24WC08 has */
/* 16 byte page write mode using*/
- /* last 4 bits of the address */
+ /* last 4 bits of the address */
#else
/* CAT24WC32/64... */
-#define CFG_I2C_EEPROM_ADDR_LEN 2 /* Bytes of address */
-/* mask of address bits that overflow into the "EEPROM chip address" */
+#define CFG_I2C_EEPROM_ADDR_LEN 2 /* Bytes of address */
+/* mask of address bits that overflow into the "EEPROM chip address" */
#define CFG_I2C_EEPROM_ADDR_OVERFLOW 0x01
#define CFG_EEPROM_PAGE_WRITE_BITS 5 /* The Catalyst CAT24WC32 has */
/* 32 byte page write mode using*/
- /* last 5 bits of the address */
+ /* last 5 bits of the address */
#endif
#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
#define CFG_EEPROM_PAGE_WRITE_ENABLE
@@ -309,8 +309,8 @@
/*-----------------------------------------------------------------------
* Cache Configuration
*/
-#define CFG_DCACHE_SIZE 16384 /* For IBM 405 CPUs, older 405 ppc's */
- /* have only 8kB, 16kB is save here */
+#define CFG_DCACHE_SIZE 16384 /* For IBM 405 CPUs, older 405 ppc's */
+ /* have only 8kB, 16kB is save here */
#define CFG_CACHELINE_SIZE 32 /* ... */
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
@@ -320,63 +320,63 @@
* External Bus Controller (EBC) Setup
*/
-#define CAN_BA 0xF0000000 /* CAN Base Address */
-#define DUART0_BA 0xF0000400 /* DUART Base Address */
-#define DUART1_BA 0xF0000408 /* DUART Base Address */
-#define RTC_BA 0xF0000500 /* RTC Base Address */
-#define VGA_BA 0xF1000000 /* Epson VGA Base Address */
-#define CFG_NAND_BASE 0xF4000000 /* NAND FLASH Base Address */
+#define CAN_BA 0xF0000000 /* CAN Base Address */
+#define DUART0_BA 0xF0000400 /* DUART Base Address */
+#define DUART1_BA 0xF0000408 /* DUART Base Address */
+#define RTC_BA 0xF0000500 /* RTC Base Address */
+#define VGA_BA 0xF1000000 /* Epson VGA Base Address */
+#define CFG_NAND_BASE 0xF4000000 /* NAND FLASH Base Address */
-/* Memory Bank 0 (Flash Bank 0, NOR-FLASH) initialization */
-#define CFG_EBC_PB0AP 0x92015480
-/*#define CFG_EBC_PB0AP 0x08055880 /XXX* TWT=16,CSN=1,OEN=1,WBN=1,WBF=1,TH=4,SOR=1 */
-#define CFG_EBC_PB0CR 0xFFC5A000 /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
+/* Memory Bank 0 (Flash Bank 0, NOR-FLASH) initialization */
+#define CFG_EBC_PB0AP 0x92015480
+/*#define CFG_EBC_PB0AP 0x08055880 /XXX* TWT=16,CSN=1,OEN=1,WBN=1,WBF=1,TH=4,SOR=1 */
+#define CFG_EBC_PB0CR 0xFFC5A000 /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
-/* Memory Bank 1 (Flash Bank 1, NAND-FLASH) initialization */
-#define CFG_EBC_PB1AP 0x92015480
-#define CFG_EBC_PB1CR 0xF4018000 /* BAS=0xF40,BS=1MB,BU=R/W,BW=8bit */
+/* Memory Bank 1 (Flash Bank 1, NAND-FLASH) initialization */
+#define CFG_EBC_PB1AP 0x92015480
+#define CFG_EBC_PB1CR 0xF4018000 /* BAS=0xF40,BS=1MB,BU=R/W,BW=8bit */
-/* Memory Bank 2 (8 Bit Peripheral: CAN, UART, RTC) initialization */
-#define CFG_EBC_PB2AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
-#define CFG_EBC_PB2CR 0xF0018000 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */
+/* Memory Bank 2 (8 Bit Peripheral: CAN, UART, RTC) initialization */
+#define CFG_EBC_PB2AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
+#define CFG_EBC_PB2CR 0xF0018000 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */
-/* Memory Bank 3 (16 Bit Peripheral: FPGA internal, dig. IO) initialization */
-#define CFG_EBC_PB3AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
-#define CFG_EBC_PB3CR 0xF011A000 /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */
+/* Memory Bank 3 (16 Bit Peripheral: FPGA internal, dig. IO) initialization */
+#define CFG_EBC_PB3AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
+#define CFG_EBC_PB3CR 0xF011A000 /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */
-/* Memory Bank 4 (Epson VGA) initialization */
-#define CFG_EBC_PB4AP 0x03805380 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=0 */
-#define CFG_EBC_PB4CR VGA_BA | 0x7A000 /* BAS=0xF10,BS=8MB,BU=R/W,BW=16bit */
+/* Memory Bank 4 (Epson VGA) initialization */
+#define CFG_EBC_PB4AP 0x03805380 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=0 */
+#define CFG_EBC_PB4CR VGA_BA | 0x7A000 /* BAS=0xF10,BS=8MB,BU=R/W,BW=16bit */
/*-----------------------------------------------------------------------
* FPGA stuff
*/
-#define CFG_FPGA_BASE_ADDR 0xF0100100 /* FPGA internal Base Address */
+#define CFG_FPGA_BASE_ADDR 0xF0100100 /* FPGA internal Base Address */
/* FPGA internal regs */
-#define CFG_FPGA_CTRL 0x000
+#define CFG_FPGA_CTRL 0x000
/* FPGA Control Reg */
-#define CFG_FPGA_CTRL_CF_RESET 0x0001
-#define CFG_FPGA_CTRL_WDI 0x0002
+#define CFG_FPGA_CTRL_CF_RESET 0x0001
+#define CFG_FPGA_CTRL_WDI 0x0002
#define CFG_FPGA_CTRL_PS2_RESET 0x0020
-#define CFG_FPGA_SPARTAN2 1 /* using Xilinx Spartan 2 now */
-#define CFG_FPGA_MAX_SIZE 128*1024 /* 128kByte is enough for XC2S50E*/
+#define CFG_FPGA_SPARTAN2 1 /* using Xilinx Spartan 2 now */
+#define CFG_FPGA_MAX_SIZE 128*1024 /* 128kByte is enough for XC2S50E*/
/* FPGA program pin configuration */
-#define CFG_FPGA_PRG 0x04000000 /* FPGA program pin (ppc output) */
-#define CFG_FPGA_CLK 0x02000000 /* FPGA clk pin (ppc output) */
-#define CFG_FPGA_DATA 0x01000000 /* FPGA data pin (ppc output) */
-#define CFG_FPGA_INIT 0x00010000 /* FPGA init pin (ppc input) */
-#define CFG_FPGA_DONE 0x00008000 /* FPGA done pin (ppc input) */
+#define CFG_FPGA_PRG 0x04000000 /* FPGA program pin (ppc output) */
+#define CFG_FPGA_CLK 0x02000000 /* FPGA clk pin (ppc output) */
+#define CFG_FPGA_DATA 0x01000000 /* FPGA data pin (ppc output) */
+#define CFG_FPGA_INIT 0x00010000 /* FPGA init pin (ppc input) */
+#define CFG_FPGA_DONE 0x00008000 /* FPGA done pin (ppc input) */
/*-----------------------------------------------------------------------
* Definitions for initial stack pointer and data area (in data cache)
*/
/* use on chip memory ( OCM ) for temperary stack until sdram is tested */
-#define CFG_TEMP_STACK_OCM 1
+#define CFG_TEMP_STACK_OCM 1
/* On Chip Memory location */
#define CFG_OCM_DATA_ADDR 0xF8000000
@@ -386,13 +386,13 @@
#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
/*-----------------------------------------------------------------------
* Definitions for GPIO setup (PPC405EP specific)
*
- * GPIO0[0] - External Bus Controller BLAST output
- * GPIO0[1-9] - Instruction trace outputs -> GPIO
+ * GPIO0[0] - External Bus Controller BLAST output
+ * GPIO0[1-9] - Instruction trace outputs -> GPIO
* GPIO0[10-13] - External Bus Controller CS_1 - CS_4 outputs
* GPIO0[14-16] - External Bus Controller ABUS3-ABUS5 outputs -> GPIO
* GPIO0[17-23] - External Interrupts IRQ0 - IRQ6 inputs
@@ -400,15 +400,15 @@
* GPIO0[28-29] - UART1 data signal input/output
* GPIO0[30-31] - EMAC0 and EMAC1 reject packet inputs
*/
-#define CFG_GPIO0_OSRH 0x40000550
-#define CFG_GPIO0_OSRL 0x00000110
-#define CFG_GPIO0_ISR1H 0x00000000
-#define CFG_GPIO0_ISR1L 0x15555445
-#define CFG_GPIO0_TSRH 0x00000000
-#define CFG_GPIO0_TSRL 0x00000000
-#define CFG_GPIO0_TCR 0xF7FE0014
+#define CFG_GPIO0_OSRH 0x40000550
+#define CFG_GPIO0_OSRL 0x00000110
+#define CFG_GPIO0_ISR1H 0x00000000
+#define CFG_GPIO0_ISR1L 0x15555445
+#define CFG_GPIO0_TSRH 0x00000000
+#define CFG_GPIO0_TSRL 0x00000000
+#define CFG_GPIO0_TCR 0xF7FE0014
-#define CFG_DUART_RST (0x80000000 >> 14)
+#define CFG_DUART_RST (0x80000000 >> 14)
/*
* Internal Definitions
@@ -423,16 +423,16 @@
* This value will be set if iic boot eprom is disabled.
*/
#if 1
-#define PLLMR0_DEFAULT PLLMR0_266_133_66_33
-#define PLLMR1_DEFAULT PLLMR1_266_133_66_33
+#define PLLMR0_DEFAULT PLLMR0_266_133_66_33
+#define PLLMR1_DEFAULT PLLMR1_266_133_66_33
#endif
#if 0
-#define PLLMR0_DEFAULT PLLMR0_200_100_50_33
-#define PLLMR1_DEFAULT PLLMR1_200_100_50_33
+#define PLLMR0_DEFAULT PLLMR0_200_100_50_33
+#define PLLMR1_DEFAULT PLLMR1_200_100_50_33
#endif
#if 0
-#define PLLMR0_DEFAULT PLLMR0_133_66_66_33
-#define PLLMR1_DEFAULT PLLMR1_133_66_66_33
+#define PLLMR0_DEFAULT PLLMR0_133_66_66_33
+#define PLLMR1_DEFAULT PLLMR1_133_66_66_33
#endif
#endif /* __CONFIG_H */
diff --git a/include/configs/W7OLMC.h b/include/configs/W7OLMC.h
index 7ae1c70..ae3f1f4 100644
--- a/include/configs/W7OLMC.h
+++ b/include/configs/W7OLMC.h
@@ -38,7 +38,8 @@
#define CONFIG_W7O 1 /* ...on a Wave 7 Optics board */
#define CONFIG_W7OLMC 1 /* ...specifically an LMC */
-#define CONFIG_BOARD_PRE_INIT 1 /* Call board_pre_init */
+#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
+#define CONFIG_MISC_INIT_F 1 /* and misc_init_f() */
#define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */
diff --git a/include/configs/W7OLMG.h b/include/configs/W7OLMG.h
index 89373b9..2a78082 100644
--- a/include/configs/W7OLMG.h
+++ b/include/configs/W7OLMG.h
@@ -38,7 +38,8 @@
#define CONFIG_W7O 1 /* ...on a Wave 7 Optics board */
#define CONFIG_W7OLMG 1 /* ...specifically an LMG */
-#define CONFIG_BOARD_PRE_INIT 1 /* Call board_pre_init */
+#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
+#define CONFIG_MISC_INIT_F 1 /* and misc_init_f() */
#define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */
diff --git a/include/configs/WALNUT405.h b/include/configs/WALNUT405.h
index cdc9a3c..9155ce8 100644
--- a/include/configs/WALNUT405.h
+++ b/include/configs/WALNUT405.h
@@ -37,7 +37,7 @@
#define CONFIG_4xx 1 /* ...member of PPC4xx family */
#define CONFIG_WALNUT405 1 /* ...on a WALNUT405 board */
-#define CONFIG_BOARD_PRE_INIT 1 /* Call board_pre_init */
+#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
#define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */
diff --git a/include/configs/ZPC1900.h b/include/configs/ZPC1900.h
index a46b9fa..673d9e5 100644
--- a/include/configs/ZPC1900.h
+++ b/include/configs/ZPC1900.h
@@ -33,7 +33,7 @@
#undef DEBUG
-#undef CONFIG_BOARD_PRE_INIT /* Don't call board_pre_init */
+#undef CONFIG_BOARD_EARLY_INIT_F /* Don't call board_early_init_f */
/* Allow serial number (serial) and MAC address (ethaddr) to be overwritten */
#define CONFIG_ENV_OVERWRITE
diff --git a/include/configs/ZUMA.h b/include/configs/ZUMA.h
index 3fde238..578f152 100644
--- a/include/configs/ZUMA.h
+++ b/include/configs/ZUMA.h
@@ -53,7 +53,7 @@
/* which initialization functions to call for this board */
#define CONFIG_MISC_INIT_R
-#define CONFIG_BOARD_PRE_INIT
+#define CONFIG_BOARD_EARLY_INIT_F
#define CFG_BOARD_ASM_INIT
#define CFG_BOARD_NAME "Zuma APv2"
diff --git a/include/configs/bms2003.h b/include/configs/bms2003.h
index 810a538..40baad0 100644
--- a/include/configs/bms2003.h
+++ b/include/configs/bms2003.h
@@ -50,8 +50,9 @@
#define CONFIG_BAUDRATE 115200 /* console baudrate = 115kbps */
#define CONFIG_PS2KBD /* AT-PS/2 Keyboard */
-#define CONFIG_PS2MULT /* .. on PS/2 Multiplexer */
+#define CONFIG_PS2MULT /* .. on PS/2 Multiplexer */
#define CONFIG_PS2SERIAL 2 /* .. on COM3 */
+#define CONFIG_PS2MULT_DELAY (CFG_HZ/2) /* Initial delay */
#define CONFIG_BOOTCOUNT_LIMIT
@@ -83,7 +84,8 @@
""
#define CONFIG_BOOTCOMMAND "run flash_self"
-#define CONFIG_MISC_INIT_R 1
+#define CONFIG_BOARD_EARLY_INIT_R 1
+#define CONFIG_MISC_INIT_R 1
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#undef CFG_LOADS_BAUD_CHANGE /* don't allow baudrate change */
diff --git a/include/configs/cogent_mpc8260.h b/include/configs/cogent_mpc8260.h
index d730527..b3ec89b 100644
--- a/include/configs/cogent_mpc8260.h
+++ b/include/configs/cogent_mpc8260.h
@@ -36,6 +36,8 @@
#define CONFIG_MPC8260 1 /* This is an MPC8260 CPU */
#define CONFIG_COGENT 1 /* using Cogent Modular Architecture */
+#define CONFIG_MISC_INIT_F 1 /* Use misc_init_f() */
+
/* Cogent Modular Architecture options */
#define CONFIG_CMA282 1 /* ...on a CMA282 CPU module */
#define CONFIG_CMA111 1 /* ...on a CMA111 motherboard */
diff --git a/include/configs/cogent_mpc8xx.h b/include/configs/cogent_mpc8xx.h
index 51d4a7a..80962d3 100644
--- a/include/configs/cogent_mpc8xx.h
+++ b/include/configs/cogent_mpc8xx.h
@@ -36,6 +36,8 @@
#define CONFIG_MPC860 1 /* This is an MPC860 CPU */
#define CONFIG_COGENT 1 /* using Cogent Modular Architecture */
+#define CONFIG_MISC_INIT_F 1 /* Use misc_init_f() */
+
/* Cogent Modular Architecture options */
#define CONFIG_CMA286_60_OLD 1 /* ...on an old CMA286-60 CPU module */
#define CONFIG_CMA102 1 /* ...on a CMA102 motherboard */
diff --git a/include/configs/ep8260.h b/include/configs/ep8260.h
index f1b2cc1..8af139b 100644
--- a/include/configs/ep8260.h
+++ b/include/configs/ep8260.h
@@ -309,7 +309,7 @@
#define CONFIG_MPC8260 1 /* This is an MPC8260 CPU */
#define CONFIG_EP8260 11 /* on an Embedded Planet EP8260 Board, Rev. 11 */
-#define CONFIG_BOARD_PRE_INIT 1 /* Call board_pre_init */
+#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
#include <cmd_confdefs.h>
diff --git a/include/configs/hymod.h b/include/configs/hymod.h
index 62b025c..e5680a5 100644
--- a/include/configs/hymod.h
+++ b/include/configs/hymod.h
@@ -36,6 +36,8 @@
#define CONFIG_MPC8260 1 /* This is an MPC8260 CPU */
#define CONFIG_HYMOD 1 /* ...on a Hymod board */
+#define CONFIG_MISC_INIT_F 1 /* Use misc_init_f() */
+
#define CONFIG_BOARD_POSTCLK_INIT /* have board_postclk_init() function */
/*
diff --git a/include/configs/lubbock.h b/include/configs/lubbock.h
index bfced44..8645a97 100644
--- a/include/configs/lubbock.h
+++ b/include/configs/lubbock.h
@@ -44,7 +44,7 @@
#define CONFIG_LUBBOCK 1 /* on an LUBBOCK Board */
#define CONFIG_LCD 1
#define CONFIG_MMC 1
-#define BOARD_POST_INIT 1
+#define BOARD_LATE_INIT 1
#undef CONFIG_USE_IRQ /* we don't need IRQ/FIQ stuff */
diff --git a/include/configs/lwmon.h b/include/configs/lwmon.h
index 04215a6..4917258 100644
--- a/include/configs/lwmon.h
+++ b/include/configs/lwmon.h
@@ -39,7 +39,7 @@
#define CONFIG_MPC823 1 /* This is a MPC823E CPU */
#define CONFIG_LWMON 1 /* ...on a LWMON board */
-#define CONFIG_BOARD_PRE_INIT 1 /* Call board_pre_init */
+#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
#define CONFIG_BOARD_POSTCLK_INIT 1 /* Call board_postclk_init */
#define CONFIG_LCD 1 /* use LCD controller ... */
@@ -282,6 +282,9 @@
#define CFG_FLASH_ERASE_TOUT 180000 /* Timeout for Flash Erase (in ms) */
#define CFG_FLASH_WRITE_TOUT 600 /* Timeout for Flash Write (in ms) */
+#define CFG_FLASH_USE_BUFFER_WRITE
+#define CFG_FLASH_BUFFER_WRITE_TOUT 2048 /* Timeout for Flash Buffer Write (in ms) */
+#define CFG_FLASH_BUFFER_SIZE 32 /* Buffer size */
#if 1
/* Put environment in flash which is much faster to boot */
diff --git a/include/configs/rsdproto.h b/include/configs/rsdproto.h
index d71b3e9..b1f6cb2 100644
--- a/include/configs/rsdproto.h
+++ b/include/configs/rsdproto.h
@@ -38,6 +38,8 @@
#define CONFIG_MPC8260 1 /* This is an MPC8260 CPU */
#define CONFIG_RSD_PROTO 1 /* on a R&S Protocol Board */
+#define CONFIG_MISC_INIT_F 1 /* Use misc_init_f() */
+
/*
* select serial console configuration
*
diff --git a/include/ps2mult.h b/include/ps2mult.h
index 8da20fc..e685817 100644
--- a/include/ps2mult.h
+++ b/include/ps2mult.h
@@ -21,6 +21,10 @@
#define PS2BUF_SIZE 512 /* power of 2, please */
+#ifndef CONFIG_PS2MULT_DELAY
+#define CONFIG_PS2MULT_DELAY (CFG_HZ/2) /* Initial delay */
+#endif
+
/* PS/2 controller interface (include/asm/keyboard.h)
*/
extern int ps2mult_init (void);
@@ -30,6 +34,7 @@
extern void ps2mult_write_output(u_char val);
extern void ps2mult_write_command(u_char val);
+extern void ps2mult_early_init (void);
extern void ps2mult_callback (int in_cnt);
/* Simple serial interface
diff --git a/lib_arm/board.c b/lib_arm/board.c
index cca708c..1591ba2 100644
--- a/lib_arm/board.c
+++ b/lib_arm/board.c
@@ -337,8 +337,8 @@
}
#endif /* CFG_CMD_NET */
-#ifdef BOARD_POST_INIT
- board_post_init ();
+#ifdef BOARD_LATE_INIT
+ board_late_init ();
#endif
/* main_loop() can return to retry autoboot, if so just run it again. */
diff --git a/lib_nios/board.c b/lib_nios/board.c
index 693651b..08085c2 100644
--- a/lib_nios/board.c
+++ b/lib_nios/board.c
@@ -90,8 +90,8 @@
init_fnc_t *init_sequence[] = {
-#if defined(CONFIG_BOARD_PRE_INIT)
- board_pre_init, /* Call board-specific init code early.*/
+#if defined(CONFIG_BOARD_EARLY_INIT_F)
+ board_early_init_f, /* Call board-specific init code early.*/
#endif
env_init,
diff --git a/lib_ppc/board.c b/lib_ppc/board.c
index d18a9a3..c495d49 100644
--- a/lib_ppc/board.c
+++ b/lib_ppc/board.c
@@ -257,10 +257,9 @@
init_fnc_t *init_sequence[] = {
-#if defined(CONFIG_BOARD_PRE_INIT)
- board_pre_init, /* very early board init code (fpga boot, etc.) */
+#if defined(CONFIG_BOARD_EARLY_INIT_F)
+ board_early_init_f,
#endif
-
get_clocks, /* get CPU and bus clocks (etc.) */
init_timebase,
#ifdef CFG_ALLOC_DPRAM
@@ -286,11 +285,7 @@
#endif /* CONFIG_MPC5XXX */
checkboard,
INIT_FUNC_WATCHDOG_INIT
-#if defined(CONFIG_BMW) || \
- defined(CONFIG_COGENT) || \
- defined(CONFIG_HYMOD) || \
- defined(CONFIG_RSD_PROTO) || \
- defined(CONFIG_W7O)
+#if defined(CONFIG_MISC_INIT_F)
misc_init_f,
#endif
INIT_FUNC_WATCHDOG_RESET
@@ -460,15 +455,15 @@
* Save local variables to board info struct
*/
- bd->bi_memstart = CFG_SDRAM_BASE; /* start of DRAM memory */
+ bd->bi_memstart = CFG_SDRAM_BASE; /* start of DRAM memory */
bd->bi_memsize = gd->ram_size; /* size of DRAM memory in bytes */
#ifdef CONFIG_IP860
- bd->bi_sramstart = SRAM_BASE; /* start of SRAM memory */
- bd->bi_sramsize = SRAM_SIZE; /* size of SRAM memory */
+ bd->bi_sramstart = SRAM_BASE; /* start of SRAM memory */
+ bd->bi_sramsize = SRAM_SIZE; /* size of SRAM memory */
#else
- bd->bi_sramstart = 0; /* FIXME */ /* start of SRAM memory */
- bd->bi_sramsize = 0; /* FIXME */ /* size of SRAM memory */
+ bd->bi_sramstart = 0; /* FIXME */ /* start of SRAM memory */
+ bd->bi_sramsize = 0; /* FIXME */ /* size of SRAM memory */
#endif
#if defined(CONFIG_8xx) || defined(CONFIG_8260) || defined(CONFIG_5xx) || \
@@ -569,6 +564,10 @@
WATCHDOG_RESET ();
+#if defined(CONFIG_BOARD_EARLY_INIT_R)
+ board_early_init_r ();
+#endif
+
gd->reloc_off = dest_addr - CFG_MONITOR_BASE;
monitor_flash_len = (ulong)&__init_end - dest_addr;
@@ -622,7 +621,7 @@
#endif
#if defined(CFG_INIT_RAM_LOCK) && defined(CONFIG_E500)
- unlock_ram_in_cache(); /* it's time to unlock D-cache in e500 */
+ unlock_ram_in_cache(); /* it's time to unlock D-cache in e500 */
#endif
#if defined(CONFIG_BAB7xx) || defined(CONFIG_CPC45)
diff --git a/post/ether.c b/post/ether.c
index 0a8b36f..b041a43 100644
--- a/post/ether.c
+++ b/post/ether.c
@@ -70,6 +70,7 @@
static struct {
void (*init) (int index);
+ void (*halt) (int index);
int (*send) (int index, volatile void *packet, int length);
int (*recv) (int index, void *packet, int length);
} ctlr_proc[1];
@@ -77,7 +78,6 @@
static char *ctlr_name[1] = { "SCC" };
static int used_by_uart[1] = { -1 };
-static int used_by_ether[1] = { -1 };
/* Ethernet Transmit and Receive Buffers */
#define DBUF_LENGTH 1520
@@ -452,6 +452,14 @@
#endif
}
+static void scc_halt (int scc_index)
+{
+ volatile immap_t *immr = (immap_t *) CFG_IMMR;
+
+ immr->im_cpm.cp_scc[scc_index].scc_gsmrl &=
+ ~(SCC_GSMRL_ENR | SCC_GSMRL_ENT);
+}
+
static int scc_send (int index, volatile void *packet, int length)
{
int i, j = 0;
@@ -573,20 +581,14 @@
Done:
+ ctlr_proc[ctlr].halt (index);
+
#if !defined(CONFIG_8xx_CONS_NONE)
if (used_by_uart[ctlr] == index) {
serial_init ();
}
#endif
-#if defined(SCC_ENET)
- if (used_by_ether[ctlr] == index) {
- DECLARE_GLOBAL_DATA_PTR;
-
- eth_init (gd->bd);
- }
-#endif
-
/*
* SCC2 Ethernet parameter RAM space overlaps
* the SPI parameter RAM space. So we need to restore
@@ -622,11 +624,8 @@
used_by_uart[CTLR_SCC] = 3;
#endif
-#if defined(SCC_ENET)
- used_by_ether[CTLR_SCC] = SCC_ENET;
-#endif
-
ctlr_proc[CTLR_SCC].init = scc_init;
+ ctlr_proc[CTLR_SCC].halt = scc_halt;
ctlr_proc[CTLR_SCC].send = scc_send;
ctlr_proc[CTLR_SCC].recv = scc_recv;
diff --git a/post/uart.c b/post/uart.c
index 15df74e..f6936ca 100644
--- a/post/uart.c
+++ b/post/uart.c
@@ -72,17 +72,14 @@
static char *ctlr_name[2] = { "SMC", "SCC" };
static int used_by_uart[2] = { -1, -1 };
-#if defined(SCC_ENET)
-static int used_by_ether[2] = { -1, -1 };
-#endif
static int proff_smc[] = { PROFF_SMC1, PROFF_SMC2 };
static int proff_scc[] =
{ PROFF_SCC1, PROFF_SCC2, PROFF_SCC3, PROFF_SCC4 };
- /*
- * SMC callbacks
- */
+/*
+ * SMC callbacks
+ */
static void smc_init (int smc_index)
{
@@ -523,14 +520,6 @@
}
#endif
-#if defined(SCC_ENET)
- if (used_by_ether[ctlr] == index) {
- DECLARE_GLOBAL_DATA_PTR;
-
- eth_init (gd->bd);
- }
-#endif
-
if (res != 0) {
post_log ("uart %s%d test failed\n",
ctlr_name[ctlr], index + 1);
@@ -558,10 +547,6 @@
used_by_uart[CTLR_SCC] = 3;
#endif
-#if defined(SCC_ENET)
- used_by_ether[CTLR_SCC] = SCC_ENET;
-#endif
-
ctlr_proc[CTLR_SMC].init = smc_init;
ctlr_proc[CTLR_SMC].putc = smc_putc;
ctlr_proc[CTLR_SMC].getc = smc_getc;