Initial revision
diff --git a/drivers/tigon3.c b/drivers/tigon3.c
new file mode 100644
index 0000000..5883744
--- /dev/null
+++ b/drivers/tigon3.c
@@ -0,0 +1,6222 @@
+/******************************************************************************/
+/* */
+/* Broadcom BCM5700 Linux Network Driver, Copyright (c) 2000 Broadcom */
+/* Corporation. */
+/* All rights reserved. */
+/* */
+/* This program is free software; you can redistribute it and/or modify */
+/* it under the terms of the GNU General Public License as published by */
+/* the Free Software Foundation, located in the file LICENSE. */
+/* */
+/* History: */
+/******************************************************************************/
+#include <common.h>
+#include "bcm570x_mm.h"
+#include <asm/types.h>
+#if (CONFIG_COMMANDS & CFG_CMD_NET) && !defined(CONFIG_NET_MULTI) && \
+ defined(CONFIG_TIGON3)
+#ifdef CONFIG_BMW
+#include <mpc824x.h>
+#endif
+#include <malloc.h>
+#include <linux/byteorder/big_endian.h>
+
+#define EMBEDDED 1
+/******************************************************************************/
+/* Local functions. */
+/******************************************************************************/
+
+LM_STATUS LM_Abort(PLM_DEVICE_BLOCK pDevice);
+LM_STATUS LM_QueueRxPackets(PLM_DEVICE_BLOCK pDevice);
+
+static LM_STATUS LM_TranslateRequestedMediaType(
+ LM_REQUESTED_MEDIA_TYPE RequestedMediaType,
+ PLM_MEDIA_TYPE pMediaType, PLM_LINE_SPEED pLineSpeed,
+ PLM_DUPLEX_MODE pDuplexMode);
+
+static LM_STATUS LM_InitBcm540xPhy(PLM_DEVICE_BLOCK pDevice);
+
+__inline static LM_VOID LM_ServiceRxInterrupt(PLM_DEVICE_BLOCK pDevice);
+__inline static LM_VOID LM_ServiceTxInterrupt(PLM_DEVICE_BLOCK pDevice);
+
+static LM_STATUS LM_ForceAutoNegBcm540xPhy(PLM_DEVICE_BLOCK pDevice,
+ LM_REQUESTED_MEDIA_TYPE RequestedMediaType);
+static LM_STATUS LM_ForceAutoNeg(PLM_DEVICE_BLOCK pDevice,
+ LM_REQUESTED_MEDIA_TYPE RequestedMediaType);
+static LM_UINT32 GetPhyAdFlowCntrlSettings(PLM_DEVICE_BLOCK pDevice);
+STATIC LM_STATUS LM_SetFlowControl(PLM_DEVICE_BLOCK pDevice,
+ LM_UINT32 LocalPhyAd, LM_UINT32 RemotePhyAd);
+#if INCLUDE_TBI_SUPPORT
+STATIC LM_STATUS LM_SetupFiberPhy(PLM_DEVICE_BLOCK pDevice);
+STATIC LM_STATUS LM_InitBcm800xPhy(PLM_DEVICE_BLOCK pDevice);
+#endif
+STATIC LM_STATUS LM_SetupCopperPhy(PLM_DEVICE_BLOCK pDevice);
+STATIC PLM_ADAPTER_INFO LM_GetAdapterInfoBySsid(LM_UINT16 Svid, LM_UINT16 Ssid);
+STATIC LM_STATUS LM_DmaTest(PLM_DEVICE_BLOCK pDevice, PLM_UINT8 pBufferVirt,
+ LM_PHYSICAL_ADDRESS BufferPhy, LM_UINT32 BufferSize);
+STATIC LM_STATUS LM_HaltCpu(PLM_DEVICE_BLOCK pDevice,LM_UINT32 cpu_number);
+STATIC LM_STATUS LM_ResetChip(PLM_DEVICE_BLOCK pDevice);
+STATIC LM_STATUS LM_Test4GBoundary(PLM_DEVICE_BLOCK pDevice, PLM_PACKET pPacket,
+ PT3_SND_BD pSendBd);
+
+/******************************************************************************/
+/* External functions. */
+/******************************************************************************/
+
+LM_STATUS LM_LoadRlsFirmware(PLM_DEVICE_BLOCK pDevice);
+
+
+/******************************************************************************/
+/* Description: */
+/* */
+/* Return: */
+/******************************************************************************/
+LM_UINT32
+LM_RegRdInd(
+PLM_DEVICE_BLOCK pDevice,
+LM_UINT32 Register) {
+ LM_UINT32 Value32;
+
+#if PCIX_TARGET_WORKAROUND
+ MM_ACQUIRE_UNDI_LOCK(pDevice);
+#endif
+ MM_WriteConfig32(pDevice, T3_PCI_REG_ADDR_REG, Register);
+ MM_ReadConfig32(pDevice, T3_PCI_REG_DATA_REG, &Value32);
+#if PCIX_TARGET_WORKAROUND
+ MM_RELEASE_UNDI_LOCK(pDevice);
+#endif
+
+ return Value32;
+} /* LM_RegRdInd */
+
+
+
+/******************************************************************************/
+/* Description: */
+/* */
+/* Return: */
+/******************************************************************************/
+LM_VOID
+LM_RegWrInd(
+PLM_DEVICE_BLOCK pDevice,
+LM_UINT32 Register,
+LM_UINT32 Value32) {
+
+#if PCIX_TARGET_WORKAROUND
+ MM_ACQUIRE_UNDI_LOCK(pDevice);
+#endif
+ MM_WriteConfig32(pDevice, T3_PCI_REG_ADDR_REG, Register);
+ MM_WriteConfig32(pDevice, T3_PCI_REG_DATA_REG, Value32);
+#if PCIX_TARGET_WORKAROUND
+ MM_RELEASE_UNDI_LOCK(pDevice);
+#endif
+} /* LM_RegWrInd */
+
+
+
+/******************************************************************************/
+/* Description: */
+/* */
+/* Return: */
+/******************************************************************************/
+LM_UINT32
+LM_MemRdInd(
+PLM_DEVICE_BLOCK pDevice,
+LM_UINT32 MemAddr) {
+ LM_UINT32 Value32;
+
+ MM_ACQUIRE_UNDI_LOCK(pDevice);
+#ifdef BIG_ENDIAN_HOST
+ MM_WriteConfig32(pDevice, T3_PCI_MEM_WIN_ADDR_REG, MemAddr);
+ Value32 = REG_RD(pDevice, PciCfg.MemWindowData);
+ /* Value32 = REG_RD(pDevice,uIntMem.Mbuf[(MemAddr & 0x7fff)/4]); */
+#else
+ MM_WriteConfig32(pDevice, T3_PCI_MEM_WIN_ADDR_REG, MemAddr);
+ MM_ReadConfig32(pDevice, T3_PCI_MEM_WIN_DATA_REG, &Value32);
+#endif
+ MM_RELEASE_UNDI_LOCK(pDevice);
+
+ return Value32;
+} /* LM_MemRdInd */
+
+
+
+/******************************************************************************/
+/* Description: */
+/* */
+/* Return: */
+/******************************************************************************/
+LM_VOID
+LM_MemWrInd(
+PLM_DEVICE_BLOCK pDevice,
+LM_UINT32 MemAddr,
+LM_UINT32 Value32) {
+ MM_ACQUIRE_UNDI_LOCK(pDevice);
+#ifdef BIG_ENDIAN_HOST
+ REG_WR(pDevice,PciCfg.MemWindowBaseAddr,MemAddr);
+ REG_WR(pDevice,uIntMem.Mbuf[(MemAddr & 0x7fff)/4],Value32);
+#else
+ MM_WriteConfig32(pDevice, T3_PCI_MEM_WIN_ADDR_REG, MemAddr);
+ MM_WriteConfig32(pDevice, T3_PCI_MEM_WIN_DATA_REG, Value32);
+#endif
+ MM_RELEASE_UNDI_LOCK(pDevice);
+} /* LM_MemWrInd */
+
+
+
+/******************************************************************************/
+/* Description: */
+/* */
+/* Return: */
+/******************************************************************************/
+LM_STATUS
+LM_QueueRxPackets(
+PLM_DEVICE_BLOCK pDevice) {
+ LM_STATUS Lmstatus;
+ PLM_PACKET pPacket;
+ PT3_RCV_BD pRcvBd;
+ LM_UINT32 StdBdAdded = 0;
+#if T3_JUMBO_RCV_RCB_ENTRY_COUNT
+ LM_UINT32 JumboBdAdded = 0;
+#endif /* T3_JUMBO_RCV_RCB_ENTRY_COUNT */
+
+ Lmstatus = LM_STATUS_SUCCESS;
+
+ pPacket = (PLM_PACKET) QQ_PopHead(&pDevice->RxPacketFreeQ.Container);
+ while(pPacket) {
+ switch(pPacket->u.Rx.RcvProdRing) {
+#if T3_JUMBO_RCV_RCB_ENTRY_COUNT
+ case T3_JUMBO_RCV_PROD_RING: /* Jumbo Receive Ring. */
+ /* Initialize the buffer descriptor. */
+ pRcvBd =
+ &pDevice->pRxJumboBdVirt[pDevice->RxJumboProdIdx];
+ pRcvBd->Flags = RCV_BD_FLAG_END | RCV_BD_FLAG_JUMBO_RING;
+ pRcvBd->Len = (LM_UINT16) pDevice->RxJumboBufferSize;
+
+ /* Initialize the receive buffer pointer */
+#if 0 /* Jimmy, deleted in new */
+ pRcvBd->HostAddr.Low = pPacket->u.Rx.RxBufferPhy.Low;
+ pRcvBd->HostAddr.High = pPacket->u.Rx.RxBufferPhy.High;
+#endif
+ MM_MapRxDma(pDevice, pPacket, &pRcvBd->HostAddr);
+
+ /* The opaque field may point to an offset from a fix addr. */
+ pRcvBd->Opaque = (LM_UINT32) (MM_UINT_PTR(pPacket) -
+ MM_UINT_PTR(pDevice->pPacketDescBase));
+
+ /* Update the producer index. */
+ pDevice->RxJumboProdIdx = (pDevice->RxJumboProdIdx + 1) &
+ T3_JUMBO_RCV_RCB_ENTRY_COUNT_MASK;
+
+ JumboBdAdded++;
+ break;
+#endif /* T3_JUMBO_RCV_RCB_ENTRY_COUNT */
+
+ case T3_STD_RCV_PROD_RING: /* Standard Receive Ring. */
+ /* Initialize the buffer descriptor. */
+ pRcvBd = &pDevice->pRxStdBdVirt[pDevice->RxStdProdIdx];
+ pRcvBd->Flags = RCV_BD_FLAG_END;
+ pRcvBd->Len = MAX_STD_RCV_BUFFER_SIZE;
+
+ /* Initialize the receive buffer pointer */
+#if 0 /* Jimmy, deleted in new replaced with MM_MapRxDma */
+ pRcvBd->HostAddr.Low = pPacket->u.Rx.RxBufferPhy.Low;
+ pRcvBd->HostAddr.High = pPacket->u.Rx.RxBufferPhy.High;
+#endif
+ MM_MapRxDma(pDevice, pPacket, &pRcvBd->HostAddr);
+
+ /* The opaque field may point to an offset from a fix addr. */
+ pRcvBd->Opaque = (LM_UINT32) (MM_UINT_PTR(pPacket) -
+ MM_UINT_PTR(pDevice->pPacketDescBase));
+
+ /* Update the producer index. */
+ pDevice->RxStdProdIdx = (pDevice->RxStdProdIdx + 1) &
+ T3_STD_RCV_RCB_ENTRY_COUNT_MASK;
+
+ StdBdAdded++;
+ break;
+
+ case T3_UNKNOWN_RCV_PROD_RING:
+ default:
+ Lmstatus = LM_STATUS_FAILURE;
+ break;
+ } /* switch */
+
+ /* Bail out if there is any error. */
+ if(Lmstatus != LM_STATUS_SUCCESS)
+ {
+ break;
+ }
+
+ pPacket = (PLM_PACKET) QQ_PopHead(&pDevice->RxPacketFreeQ.Container);
+ } /* while */
+
+ wmb();
+ /* Update the procedure index. */
+ if(StdBdAdded)
+ {
+ MB_REG_WR(pDevice, Mailbox.RcvStdProdIdx.Low, pDevice->RxStdProdIdx);
+ }
+#if T3_JUMBO_RCV_RCB_ENTRY_COUNT
+ if(JumboBdAdded)
+ {
+ MB_REG_WR(pDevice, Mailbox.RcvJumboProdIdx.Low,
+ pDevice->RxJumboProdIdx);
+ }
+#endif /* T3_JUMBO_RCV_RCB_ENTRY_COUNT */
+
+ return Lmstatus;
+} /* LM_QueueRxPackets */
+
+
+/******************************************************************************/
+/* Description: */
+/* */
+/* Return: */
+/******************************************************************************/
+STATIC LM_VOID
+LM_NvramInit(
+ PLM_DEVICE_BLOCK pDevice)
+{
+ LM_UINT32 Value32;
+ LM_UINT32 j;
+
+ /* Intialize clock period and state machine. */
+ Value32 = SEEPROM_ADDR_CLK_PERD(SEEPROM_CLOCK_PERIOD) |
+ SEEPROM_ADDR_FSM_RESET;
+ REG_WR(pDevice, Grc.EepromAddr, Value32);
+
+ for(j = 0; j < 100; j++)
+ {
+ MM_Wait(10);
+ }
+
+ /* Serial eeprom access using the Grc.EepromAddr/EepromData registers. */
+ Value32 = REG_RD(pDevice, Grc.LocalCtrl);
+ REG_WR(pDevice, Grc.LocalCtrl, Value32 | GRC_MISC_LOCAL_CTRL_AUTO_SEEPROM);
+
+ /* Set the 5701 compatibility mode if we are using EEPROM. */
+ if(T3_ASIC_REV(pDevice->ChipRevId) != T3_ASIC_REV_5700 &&
+ T3_ASIC_REV(pDevice->ChipRevId) != T3_ASIC_REV_5701)
+ {
+ Value32 = REG_RD(pDevice, Nvram.Config1);
+ if((Value32 & FLASH_INTERFACE_ENABLE) == 0)
+ {
+ /* Use the new interface to read EEPROM. */
+ Value32 &= ~FLASH_COMPAT_BYPASS;
+
+ REG_WR(pDevice, Nvram.Config1, Value32);
+ }
+ }
+} /* LM_NvRamInit */
+
+
+/******************************************************************************/
+/* Description: */
+/* */
+/* Return: */
+/******************************************************************************/
+STATIC LM_STATUS
+LM_EepromRead(
+ PLM_DEVICE_BLOCK pDevice,
+ LM_UINT32 Offset,
+ LM_UINT32 *pData)
+{
+ LM_UINT32 Value32;
+ LM_UINT32 Addr;
+ LM_UINT32 Dev;
+ LM_UINT32 j;
+
+ if(Offset > SEEPROM_CHIP_SIZE)
+ {
+ return LM_STATUS_FAILURE;
+ }
+
+ Dev = Offset / SEEPROM_CHIP_SIZE;
+ Addr = Offset % SEEPROM_CHIP_SIZE;
+
+ Value32 = REG_RD(pDevice, Grc.EepromAddr);
+ Value32 &= ~(SEEPROM_ADDR_ADDRESS_MASK | SEEPROM_ADDR_DEV_ID_MASK |
+ SEEPROM_ADDR_RW_MASK);
+ REG_WR(pDevice, Grc.EepromAddr, Value32 | SEEPROM_ADDR_DEV_ID(Dev) |
+ SEEPROM_ADDR_ADDRESS(Addr) | SEEPROM_ADDR_START | SEEPROM_ADDR_READ);
+
+ for(j = 0; j < 1000; j++)
+ {
+ Value32 = REG_RD(pDevice, Grc.EepromAddr);
+ if(Value32 & SEEPROM_ADDR_COMPLETE)
+ {
+ break;
+ }
+ MM_Wait(10);
+ }
+
+ if(Value32 & SEEPROM_ADDR_COMPLETE)
+ {
+ Value32 = REG_RD(pDevice, Grc.EepromData);
+ *pData = Value32;
+
+ return LM_STATUS_SUCCESS;
+ }
+
+ return LM_STATUS_FAILURE;
+} /* LM_EepromRead */
+
+
+
+/******************************************************************************/
+/* Description: */
+/* */
+/* Return: */
+/******************************************************************************/
+STATIC LM_STATUS
+LM_NvramRead(
+ PLM_DEVICE_BLOCK pDevice,
+ LM_UINT32 Offset,
+ LM_UINT32 *pData)
+{
+ LM_UINT32 Value32;
+ LM_STATUS Status;
+ LM_UINT32 j;
+
+ if(T3_ASIC_REV(pDevice->ChipRevId) == T3_ASIC_REV_5700 ||
+ T3_ASIC_REV(pDevice->ChipRevId) == T3_ASIC_REV_5701)
+ {
+ Status = LM_EepromRead(pDevice, Offset, pData);
+ }
+ else
+ {
+ /* Determine if we have flash or EEPROM. */
+ Value32 = REG_RD(pDevice, Nvram.Config1);
+ if(Value32 & FLASH_INTERFACE_ENABLE)
+ {
+ if(Value32 & FLASH_SSRAM_BUFFERRED_MODE)
+ {
+ Offset = ((Offset/BUFFERED_FLASH_PAGE_SIZE) <<
+ BUFFERED_FLASH_PAGE_POS) +
+ (Offset % BUFFERED_FLASH_PAGE_SIZE);
+ }
+ }
+
+ REG_WR(pDevice, Nvram.SwArb, SW_ARB_REQ_SET1);
+ for (j = 0; j < 1000; j++)
+ {
+ if (REG_RD(pDevice, Nvram.SwArb) & SW_ARB_GNT1)
+ {
+ break;
+ }
+ MM_Wait(20);
+ }
+ if (j == 1000)
+ {
+ return LM_STATUS_FAILURE;
+ }
+
+ /* Read from flash or EEPROM with the new 5703/02 interface. */
+ REG_WR(pDevice, Nvram.Addr, Offset & NVRAM_ADDRESS_MASK);
+
+ REG_WR(pDevice, Nvram.Cmd, NVRAM_CMD_RD | NVRAM_CMD_DO_IT |
+ NVRAM_CMD_FIRST | NVRAM_CMD_LAST | NVRAM_CMD_DONE);
+
+ /* Wait for the done bit to clear. */
+ for(j = 0; j < 500; j++)
+ {
+ MM_Wait(10);
+
+ Value32 = REG_RD(pDevice, Nvram.Cmd);
+ if(!(Value32 & NVRAM_CMD_DONE))
+ {
+ break;
+ }
+ }
+
+ /* Wait for the done bit. */
+ if(!(Value32 & NVRAM_CMD_DONE))
+ {
+ for(j = 0; j < 500; j++)
+ {
+ MM_Wait(10);
+
+ Value32 = REG_RD(pDevice, Nvram.Cmd);
+ if(Value32 & NVRAM_CMD_DONE)
+ {
+ MM_Wait(10);
+
+ *pData = REG_RD(pDevice, Nvram.ReadData);
+
+ /* Change the endianess. */
+ *pData = ((*pData & 0xff) << 24)| ((*pData & 0xff00) << 8)|
+ ((*pData & 0xff0000) >> 8) | ((*pData >> 24) & 0xff);
+
+ break;
+ }
+ }
+ }
+
+ REG_WR(pDevice, Nvram.SwArb, SW_ARB_REQ_CLR1);
+ if(Value32 & NVRAM_CMD_DONE)
+ {
+ Status = LM_STATUS_SUCCESS;
+ }
+ else
+ {
+ Status = LM_STATUS_FAILURE;
+ }
+ }
+
+ return Status;
+} /* LM_NvramRead */
+
+
+STATIC void
+LM_ReadVPD(PLM_DEVICE_BLOCK pDevice)
+{
+ LM_UINT32 Vpd_arr[256/4];
+ LM_UINT8 *Vpd = (LM_UINT8 *) &Vpd_arr[0];
+ LM_UINT32 *Vpd_dptr = &Vpd_arr[0];
+ LM_UINT32 Value32;
+ unsigned int j;
+
+ /* Read PN from VPD */
+ for (j = 0; j < 256; j += 4, Vpd_dptr++ )
+ {
+ if (LM_NvramRead(pDevice, 0x100 + j, &Value32) != LM_STATUS_SUCCESS) {
+ printf("BCM570x: LM_ReadVPD: VPD read failed"
+ " (no EEPROM onboard)\n");
+ return;
+ }
+ *Vpd_dptr = cpu_to_le32(Value32);
+ }
+ for (j = 0; j < 256; )
+ {
+ unsigned int Vpd_r_len;
+ unsigned int Vpd_r_end;
+
+ if ((Vpd[j] == 0x82) || (Vpd[j] == 0x91))
+ {
+ j = j + 3 + Vpd[j + 1] + (Vpd[j + 2] << 8);
+ }
+ else if (Vpd[j] == 0x90)
+ {
+ Vpd_r_len = Vpd[j + 1] + (Vpd[j + 2] << 8);
+ j += 3;
+ Vpd_r_end = Vpd_r_len + j;
+ while (j < Vpd_r_end)
+ {
+ if ((Vpd[j] == 'P') && (Vpd[j + 1] == 'N'))
+ {
+ unsigned int len = Vpd[j + 2];
+
+ if (len <= 24)
+ {
+ memcpy(pDevice->PartNo, &Vpd[j + 3], len);
+ }
+ break;
+ }
+ else
+ {
+ if (Vpd[j + 2] == 0)
+ {
+ break;
+ }
+ j = j + Vpd[j + 2];
+ }
+ }
+ break;
+ }
+ else {
+ break;
+ }
+ }
+}
+
+STATIC void
+LM_ReadBootCodeVersion(PLM_DEVICE_BLOCK pDevice)
+{
+ LM_UINT32 Value32, offset, ver_offset;
+ int i;
+
+ if (LM_NvramRead(pDevice, 0x0, &Value32) != LM_STATUS_SUCCESS)
+ return;
+ if (Value32 != 0xaa559966)
+ return;
+ if (LM_NvramRead(pDevice, 0xc, &offset) != LM_STATUS_SUCCESS)
+ return;
+
+ offset = ((offset & 0xff) << 24)| ((offset & 0xff00) << 8)|
+ ((offset & 0xff0000) >> 8) | ((offset >> 24) & 0xff);
+ if (LM_NvramRead(pDevice, offset, &Value32) != LM_STATUS_SUCCESS)
+ return;
+ if ((Value32 == 0x0300000e) &&
+ (LM_NvramRead(pDevice, offset + 4, &Value32) == LM_STATUS_SUCCESS) &&
+ (Value32 == 0)) {
+
+ if (LM_NvramRead(pDevice, offset + 8, &ver_offset) != LM_STATUS_SUCCESS)
+ return;
+ ver_offset = ((ver_offset & 0xff0000) >> 8) |
+ ((ver_offset >> 24) & 0xff);
+ for (i = 0; i < 16; i += 4) {
+ if (LM_NvramRead(pDevice, offset + ver_offset + i, &Value32) !=
+ LM_STATUS_SUCCESS)
+ {
+ return;
+ }
+ *((LM_UINT32 *) &pDevice->BootCodeVer[i]) = cpu_to_le32(Value32);
+ }
+ }
+ else {
+ char c;
+
+ if (LM_NvramRead(pDevice, 0x94, &Value32) != LM_STATUS_SUCCESS)
+ return;
+
+ i = 0;
+ c = ((Value32 & 0xff0000) >> 16);
+
+ if (c < 10) {
+ pDevice->BootCodeVer[i++] = c + '0';
+ }
+ else {
+ pDevice->BootCodeVer[i++] = (c / 10) + '0';
+ pDevice->BootCodeVer[i++] = (c % 10) + '0';
+ }
+ pDevice->BootCodeVer[i++] = '.';
+ c = (Value32 & 0xff000000) >> 24;
+ if (c < 10) {
+ pDevice->BootCodeVer[i++] = c + '0';
+ }
+ else {
+ pDevice->BootCodeVer[i++] = (c / 10) + '0';
+ pDevice->BootCodeVer[i++] = (c % 10) + '0';
+ }
+ pDevice->BootCodeVer[i] = 0;
+ }
+}
+
+STATIC void
+LM_GetBusSpeed(PLM_DEVICE_BLOCK pDevice)
+{
+ LM_UINT32 PciState = pDevice->PciState;
+ LM_UINT32 ClockCtrl;
+ char *SpeedStr = "";
+
+ if (PciState & T3_PCI_STATE_32BIT_PCI_BUS)
+ {
+ strcpy(pDevice->BusSpeedStr, "32-bit ");
+ }
+ else
+ {
+ strcpy(pDevice->BusSpeedStr, "64-bit ");
+ }
+ if (PciState & T3_PCI_STATE_CONVENTIONAL_PCI_MODE)
+ {
+ strcat(pDevice->BusSpeedStr, "PCI ");
+ if (PciState & T3_PCI_STATE_HIGH_BUS_SPEED)
+ {
+ SpeedStr = "66MHz";
+ }
+ else
+ {
+ SpeedStr = "33MHz";
+ }
+ }
+ else
+ {
+ strcat(pDevice->BusSpeedStr, "PCIX ");
+ if (pDevice->BondId == GRC_MISC_BD_ID_5704CIOBE)
+ {
+ SpeedStr = "133MHz";
+ }
+ else
+ {
+ ClockCtrl = REG_RD(pDevice, PciCfg.ClockCtrl) & 0x1f;
+ switch (ClockCtrl)
+ {
+ case 0:
+ SpeedStr = "33MHz";
+ break;
+
+ case 2:
+ SpeedStr = "50MHz";
+ break;
+
+ case 4:
+ SpeedStr = "66MHz";
+ break;
+
+ case 6:
+ SpeedStr = "100MHz";
+ break;
+
+ case 7:
+ SpeedStr = "133MHz";
+ break;
+ }
+ }
+ }
+ strcat(pDevice->BusSpeedStr, SpeedStr);
+}
+
+/******************************************************************************/
+/* Description: */
+/* This routine initializes default parameters and reads the PCI */
+/* configurations. */
+/* */
+/* Return: */
+/* LM_STATUS_SUCCESS */
+/******************************************************************************/
+LM_STATUS
+LM_GetAdapterInfo(
+PLM_DEVICE_BLOCK pDevice)
+{
+ PLM_ADAPTER_INFO pAdapterInfo;
+ LM_UINT32 Value32;
+ LM_STATUS Status;
+ LM_UINT32 j;
+ LM_UINT32 EeSigFound;
+ LM_UINT32 EePhyTypeSerdes = 0;
+ LM_UINT32 EePhyLedMode = 0;
+ LM_UINT32 EePhyId = 0;
+
+ /* Get Device Id and Vendor Id */
+ Status = MM_ReadConfig32(pDevice, PCI_VENDOR_ID_REG, &Value32);
+ if(Status != LM_STATUS_SUCCESS)
+ {
+ return Status;
+ }
+ pDevice->PciVendorId = (LM_UINT16) Value32;
+ pDevice->PciDeviceId = (LM_UINT16) (Value32 >> 16);
+
+ /* If we are not getting the write adapter, exit. */
+ if((Value32 != T3_PCI_ID_BCM5700) &&
+ (Value32 != T3_PCI_ID_BCM5701) &&
+ (Value32 != T3_PCI_ID_BCM5702) &&
+ (Value32 != T3_PCI_ID_BCM5702x) &&
+ (Value32 != T3_PCI_ID_BCM5702FE) &&
+ (Value32 != T3_PCI_ID_BCM5703) &&
+ (Value32 != T3_PCI_ID_BCM5703x) &&
+ (Value32 != T3_PCI_ID_BCM5704))
+ {
+ return LM_STATUS_FAILURE;
+ }
+
+ Status = MM_ReadConfig32(pDevice, PCI_REV_ID_REG, &Value32);
+ if(Status != LM_STATUS_SUCCESS)
+ {
+ return Status;
+ }
+ pDevice->PciRevId = (LM_UINT8) Value32;
+
+ /* Get IRQ. */
+ Status = MM_ReadConfig32(pDevice, PCI_INT_LINE_REG, &Value32);
+ if(Status != LM_STATUS_SUCCESS)
+ {
+ return Status;
+ }
+ pDevice->Irq = (LM_UINT8) Value32;
+
+ /* Get interrupt pin. */
+ pDevice->IntPin = (LM_UINT8) (Value32 >> 8);
+
+ /* Get chip revision id. */
+ Status = MM_ReadConfig32(pDevice, T3_PCI_MISC_HOST_CTRL_REG, &Value32);
+ pDevice->ChipRevId = Value32 >> 16;
+
+ /* Get subsystem vendor. */
+ Status = MM_ReadConfig32(pDevice, PCI_SUBSYSTEM_VENDOR_ID_REG, &Value32);
+ if(Status != LM_STATUS_SUCCESS)
+ {
+ return Status;
+ }
+ pDevice->SubsystemVendorId = (LM_UINT16) Value32;
+
+ /* Get PCI subsystem id. */
+ pDevice->SubsystemId = (LM_UINT16) (Value32 >> 16);
+
+ /* Get the cache line size. */
+ MM_ReadConfig32(pDevice, PCI_CACHE_LINE_SIZE_REG, &Value32);
+ pDevice->CacheLineSize = (LM_UINT8) Value32;
+ pDevice->SavedCacheLineReg = Value32;
+
+ if(pDevice->ChipRevId != T3_CHIP_ID_5703_A1 &&
+ pDevice->ChipRevId != T3_CHIP_ID_5703_A2 &&
+ pDevice->ChipRevId != T3_CHIP_ID_5704_A0)
+ {
+ pDevice->UndiFix = FALSE;
+ }
+#if !PCIX_TARGET_WORKAROUND
+ pDevice->UndiFix = FALSE;
+#endif
+ /* Map the memory base to system address space. */
+ if (!pDevice->UndiFix)
+ {
+ Status = MM_MapMemBase(pDevice);
+ if(Status != LM_STATUS_SUCCESS)
+ {
+ return Status;
+ }
+ /* Initialize the memory view pointer. */
+ pDevice->pMemView = (PT3_STD_MEM_MAP) pDevice->pMappedMemBase;
+ }
+
+#if PCIX_TARGET_WORKAROUND
+ /* store whether we are in PCI are PCI-X mode */
+ pDevice->EnablePciXFix = FALSE;
+
+ MM_ReadConfig32(pDevice, T3_PCI_STATE_REG, &Value32);
+ if((Value32 & T3_PCI_STATE_CONVENTIONAL_PCI_MODE) == 0)
+ {
+ /* Enable PCI-X workaround only if we are running on 5700 BX. */
+ if(T3_CHIP_REV(pDevice->ChipRevId) == T3_CHIP_REV_5700_BX)
+ {
+ pDevice->EnablePciXFix = TRUE;
+ }
+ }
+ if (pDevice->UndiFix)
+ {
+ pDevice->EnablePciXFix = TRUE;
+ }
+#endif
+ /* Bx bug: due to the "byte_enable bug" in PCI-X mode, the power */
+ /* management register may be clobbered which may cause the */
+ /* BCM5700 to go into D3 state. While in this state, we will */
+ /* not have memory mapped register access. As a workaround, we */
+ /* need to restore the device to D0 state. */
+ MM_ReadConfig32(pDevice, T3_PCI_PM_STATUS_CTRL_REG, &Value32);
+ Value32 |= T3_PM_PME_ASSERTED;
+ Value32 &= ~T3_PM_POWER_STATE_MASK;
+ Value32 |= T3_PM_POWER_STATE_D0;
+ MM_WriteConfig32(pDevice, T3_PCI_PM_STATUS_CTRL_REG, Value32);
+
+ /* read the current PCI command word */
+ MM_ReadConfig32(pDevice, PCI_COMMAND_REG, &Value32);
+
+ /* Make sure bus-mastering is enabled. */
+ Value32 |= PCI_BUSMASTER_ENABLE;
+
+#if PCIX_TARGET_WORKAROUND
+ /* if we are in PCI-X mode, also make sure mem-mapping and SERR#/PERR#
+ are enabled */
+ if (pDevice->EnablePciXFix == TRUE) {
+ Value32 |= (PCI_MEM_SPACE_ENABLE | PCI_SYSTEM_ERROR_ENABLE |
+ PCI_PARITY_ERROR_ENABLE);
+ }
+ if (pDevice->UndiFix)
+ {
+ Value32 &= ~PCI_MEM_SPACE_ENABLE;
+ }
+
+#endif
+
+ if(pDevice->EnableMWI)
+ {
+ Value32 |= PCI_MEMORY_WRITE_INVALIDATE;
+ }
+ else {
+ Value32 &= (~PCI_MEMORY_WRITE_INVALIDATE);
+ }
+
+ /* Error out if mem-mapping is NOT enabled for PCI systems */
+ if (!(Value32 | PCI_MEM_SPACE_ENABLE))
+ {
+ return LM_STATUS_FAILURE;
+ }
+
+ /* save the value we are going to write into the PCI command word */
+ pDevice->PciCommandStatusWords = Value32;
+
+ Status = MM_WriteConfig32(pDevice, PCI_COMMAND_REG, Value32);
+ if(Status != LM_STATUS_SUCCESS)
+ {
+ return Status;
+ }
+
+ /* Set power state to D0. */
+ LM_SetPowerState(pDevice, LM_POWER_STATE_D0);
+
+#ifdef BIG_ENDIAN_PCI
+ pDevice->MiscHostCtrl =
+ MISC_HOST_CTRL_MASK_PCI_INT |
+ MISC_HOST_CTRL_ENABLE_INDIRECT_ACCESS |
+ MISC_HOST_CTRL_ENABLE_ENDIAN_WORD_SWAP |
+ MISC_HOST_CTRL_ENABLE_PCI_STATE_REG_RW;
+#else /* No CPU Swap modes for PCI IO */
+
+ /* Setup the mode registers. */
+ pDevice->MiscHostCtrl =
+ MISC_HOST_CTRL_MASK_PCI_INT |
+ MISC_HOST_CTRL_ENABLE_ENDIAN_WORD_SWAP |
+#ifdef BIG_ENDIAN_HOST
+ MISC_HOST_CTRL_ENABLE_ENDIAN_BYTE_SWAP |
+#endif /* BIG_ENDIAN_HOST */
+ MISC_HOST_CTRL_ENABLE_INDIRECT_ACCESS |
+ MISC_HOST_CTRL_ENABLE_PCI_STATE_REG_RW;
+#endif /* !BIG_ENDIAN_PCI */
+
+ /* write to PCI misc host ctr first in order to enable indirect accesses */
+ MM_WriteConfig32(pDevice, T3_PCI_MISC_HOST_CTRL_REG, pDevice->MiscHostCtrl);
+
+ REG_WR(pDevice, PciCfg.MiscHostCtrl, pDevice->MiscHostCtrl);
+
+#ifdef BIG_ENDIAN_PCI
+ Value32 = GRC_MODE_WORD_SWAP_DATA|
+ GRC_MODE_WORD_SWAP_NON_FRAME_DATA;
+#else
+/* No CPU Swap modes for PCI IO */
+#ifdef BIG_ENDIAN_HOST
+ Value32 = GRC_MODE_BYTE_SWAP_NON_FRAME_DATA |
+ GRC_MODE_WORD_SWAP_NON_FRAME_DATA;
+#else
+ Value32 = GRC_MODE_BYTE_SWAP_NON_FRAME_DATA | GRC_MODE_BYTE_SWAP_DATA;
+#endif
+#endif /* !BIG_ENDIAN_PCI */
+
+ REG_WR(pDevice, Grc.Mode, Value32);
+
+ if(T3_ASIC_REV(pDevice->ChipRevId) == T3_ASIC_REV_5700)
+ {
+ REG_WR(pDevice, Grc.LocalCtrl, GRC_MISC_LOCAL_CTRL_GPIO_OUTPUT1 |
+ GRC_MISC_LOCAL_CTRL_GPIO_OE1);
+ }
+ MM_Wait(40);
+
+ /* Enable indirect memory access */
+ REG_WR(pDevice, MemArbiter.Mode, T3_MEM_ARBITER_MODE_ENABLE);
+
+ if (REG_RD(pDevice, PciCfg.ClockCtrl) & T3_PCI_44MHZ_CORE_CLOCK)
+ {
+ REG_WR(pDevice, PciCfg.ClockCtrl, T3_PCI_44MHZ_CORE_CLOCK |
+ T3_PCI_SELECT_ALTERNATE_CLOCK);
+ REG_WR(pDevice, PciCfg.ClockCtrl, T3_PCI_SELECT_ALTERNATE_CLOCK);
+ MM_Wait(40); /* required delay is 27usec */
+ }
+ REG_WR(pDevice, PciCfg.ClockCtrl, 0);
+ REG_WR(pDevice, PciCfg.MemWindowBaseAddr, 0);
+
+#if PCIX_TARGET_WORKAROUND
+ MM_ReadConfig32(pDevice, T3_PCI_STATE_REG, &Value32);
+ if ((pDevice->EnablePciXFix == FALSE) &&
+ ((Value32 & T3_PCI_STATE_CONVENTIONAL_PCI_MODE) == 0))
+ {
+ if (pDevice->ChipRevId == T3_CHIP_ID_5701_A0 ||
+ pDevice->ChipRevId == T3_CHIP_ID_5701_B0 ||
+ pDevice->ChipRevId == T3_CHIP_ID_5701_B2 ||
+ pDevice->ChipRevId == T3_CHIP_ID_5701_B5)
+ {
+ __raw_writel(0, &(pDevice->pMemView->uIntMem.MemBlock32K[0x300]));
+ __raw_writel(0, &(pDevice->pMemView->uIntMem.MemBlock32K[0x301]));
+ __raw_writel(0xffffffff, &(pDevice->pMemView->uIntMem.MemBlock32K[0x301]));
+ if (__raw_readl(&(pDevice->pMemView->uIntMem.MemBlock32K[0x300])))
+ {
+ pDevice->EnablePciXFix = TRUE;
+ }
+ }
+ }
+#endif
+#if 1
+ /*
+ * This code was at the beginning of else block below, but that's
+ * a bug if node address in shared memory.
+ */
+ MM_Wait(50);
+ LM_NvramInit(pDevice);
+#endif
+ /* Get the node address. First try to get in from the shared memory. */
+ /* If the signature is not present, then get it from the NVRAM. */
+ Value32 = MEM_RD_OFFSET(pDevice, T3_MAC_ADDR_HIGH_MAILBOX);
+ if((Value32 >> 16) == 0x484b)
+ {
+
+ pDevice->NodeAddress[0] = (LM_UINT8) (Value32 >> 8);
+ pDevice->NodeAddress[1] = (LM_UINT8) Value32;
+
+ Value32 = MEM_RD_OFFSET(pDevice, T3_MAC_ADDR_LOW_MAILBOX);
+
+ pDevice->NodeAddress[2] = (LM_UINT8) (Value32 >> 24);
+ pDevice->NodeAddress[3] = (LM_UINT8) (Value32 >> 16);
+ pDevice->NodeAddress[4] = (LM_UINT8) (Value32 >> 8);
+ pDevice->NodeAddress[5] = (LM_UINT8) Value32;
+
+ Status = LM_STATUS_SUCCESS;
+ }
+ else
+ {
+ Status = LM_NvramRead(pDevice, 0x7c, &Value32);
+ if(Status == LM_STATUS_SUCCESS)
+ {
+ pDevice->NodeAddress[0] = (LM_UINT8) (Value32 >> 16);
+ pDevice->NodeAddress[1] = (LM_UINT8) (Value32 >> 24);
+
+ Status = LM_NvramRead(pDevice, 0x80, &Value32);
+
+ pDevice->NodeAddress[2] = (LM_UINT8) Value32;
+ pDevice->NodeAddress[3] = (LM_UINT8) (Value32 >> 8);
+ pDevice->NodeAddress[4] = (LM_UINT8) (Value32 >> 16);
+ pDevice->NodeAddress[5] = (LM_UINT8) (Value32 >> 24);
+ }
+ }
+
+ /* Assign a default address. */
+ if(Status != LM_STATUS_SUCCESS)
+ {
+#ifndef EMBEDDED
+ printk(KERN_ERR "Cannot get MAC addr from NVRAM. Using default.\n");
+#endif
+ pDevice->NodeAddress[0] = 0x00; pDevice->NodeAddress[1] = 0x10;
+ pDevice->NodeAddress[2] = 0x18; pDevice->NodeAddress[3] = 0x68;
+ pDevice->NodeAddress[4] = 0x61; pDevice->NodeAddress[5] = 0x76;
+ }
+
+ pDevice->PermanentNodeAddress[0] = pDevice->NodeAddress[0];
+ pDevice->PermanentNodeAddress[1] = pDevice->NodeAddress[1];
+ pDevice->PermanentNodeAddress[2] = pDevice->NodeAddress[2];
+ pDevice->PermanentNodeAddress[3] = pDevice->NodeAddress[3];
+ pDevice->PermanentNodeAddress[4] = pDevice->NodeAddress[4];
+ pDevice->PermanentNodeAddress[5] = pDevice->NodeAddress[5];
+
+ /* Initialize the default values. */
+ pDevice->NoTxPseudoHdrChksum = FALSE;
+ pDevice->NoRxPseudoHdrChksum = FALSE;
+ pDevice->NicSendBd = FALSE;
+ pDevice->TxPacketDescCnt = DEFAULT_TX_PACKET_DESC_COUNT;
+ pDevice->RxStdDescCnt = DEFAULT_STD_RCV_DESC_COUNT;
+ pDevice->RxCoalescingTicks = DEFAULT_RX_COALESCING_TICKS;
+ pDevice->TxCoalescingTicks = DEFAULT_TX_COALESCING_TICKS;
+ pDevice->RxMaxCoalescedFrames = DEFAULT_RX_MAX_COALESCED_FRAMES;
+ pDevice->TxMaxCoalescedFrames = DEFAULT_TX_MAX_COALESCED_FRAMES;
+ pDevice->RxCoalescingTicksDuringInt = BAD_DEFAULT_VALUE;
+ pDevice->TxCoalescingTicksDuringInt = BAD_DEFAULT_VALUE;
+ pDevice->RxMaxCoalescedFramesDuringInt = BAD_DEFAULT_VALUE;
+ pDevice->TxMaxCoalescedFramesDuringInt = BAD_DEFAULT_VALUE;
+ pDevice->StatsCoalescingTicks = DEFAULT_STATS_COALESCING_TICKS;
+ pDevice->EnableMWI = FALSE;
+ pDevice->TxMtu = MAX_ETHERNET_PACKET_SIZE_NO_CRC;
+ pDevice->RxMtu = MAX_ETHERNET_PACKET_SIZE_NO_CRC;
+ pDevice->DisableAutoNeg = FALSE;
+ pDevice->PhyIntMode = T3_PHY_INT_MODE_AUTO;
+ pDevice->LinkChngMode = T3_LINK_CHNG_MODE_AUTO;
+ pDevice->LedMode = LED_MODE_AUTO;
+ pDevice->ResetPhyOnInit = TRUE;
+ pDevice->DelayPciGrant = TRUE;
+ pDevice->UseTaggedStatus = FALSE;
+ pDevice->OneDmaAtOnce = BAD_DEFAULT_VALUE;
+
+ pDevice->DmaMbufLowMark = T3_DEF_DMA_MBUF_LOW_WMARK_JUMBO;
+ pDevice->RxMacMbufLowMark = T3_DEF_RX_MAC_MBUF_LOW_WMARK_JUMBO;
+ pDevice->MbufHighMark = T3_DEF_MBUF_HIGH_WMARK_JUMBO;
+
+ pDevice->RequestedMediaType = LM_REQUESTED_MEDIA_TYPE_AUTO;
+ pDevice->TaskOffloadCap = LM_TASK_OFFLOAD_NONE;
+ pDevice->FlowControlCap = LM_FLOW_CONTROL_AUTO_PAUSE;
+ pDevice->EnableTbi = FALSE;
+#if INCLUDE_TBI_SUPPORT
+ pDevice->PollTbiLink = BAD_DEFAULT_VALUE;
+#endif
+
+ switch (T3_ASIC_REV(pDevice->ChipRevId))
+ {
+ case T3_ASIC_REV_5704:
+ pDevice->MbufBase = T3_NIC_MBUF_POOL_ADDR;
+ pDevice->MbufSize = T3_NIC_MBUF_POOL_SIZE64;
+ break;
+ default:
+ pDevice->MbufBase = T3_NIC_MBUF_POOL_ADDR;
+ pDevice->MbufSize = T3_NIC_MBUF_POOL_SIZE96;
+ break;
+ }
+
+ pDevice->LinkStatus = LM_STATUS_LINK_DOWN;
+ pDevice->QueueRxPackets = TRUE;
+
+ pDevice->EnableWireSpeed = TRUE;
+
+#if T3_JUMBO_RCV_RCB_ENTRY_COUNT
+ pDevice->RxJumboDescCnt = DEFAULT_JUMBO_RCV_DESC_COUNT;
+#endif /* T3_JUMBO_RCV_RCB_ENTRY_COUNT */
+
+ /* Make this is a known adapter. */
+ pAdapterInfo = LM_GetAdapterInfoBySsid(pDevice->SubsystemVendorId,
+ pDevice->SubsystemId);
+
+ pDevice->BondId = REG_RD(pDevice, Grc.MiscCfg) & GRC_MISC_BD_ID_MASK;
+ if (pDevice->BondId != GRC_MISC_BD_ID_5700 &&
+ pDevice->BondId != GRC_MISC_BD_ID_5701 &&
+ pDevice->BondId != GRC_MISC_BD_ID_5702FE &&
+ pDevice->BondId != GRC_MISC_BD_ID_5703 &&
+ pDevice->BondId != GRC_MISC_BD_ID_5703S &&
+ pDevice->BondId != GRC_MISC_BD_ID_5704 &&
+ pDevice->BondId != GRC_MISC_BD_ID_5704CIOBE)
+ {
+ return LM_STATUS_UNKNOWN_ADAPTER;
+ }
+
+ pDevice->SplitModeEnable = SPLIT_MODE_DISABLE;
+ if ((pDevice->ChipRevId == T3_CHIP_ID_5704_A0) &&
+ (pDevice->BondId == GRC_MISC_BD_ID_5704CIOBE))
+ {
+ pDevice->SplitModeEnable = SPLIT_MODE_ENABLE;
+ pDevice->SplitModeMaxReq = SPLIT_MODE_5704_MAX_REQ;
+ }
+
+ /* Get Eeprom info. */
+ Value32 = MEM_RD_OFFSET(pDevice, T3_NIC_DATA_SIG_ADDR);
+ if (Value32 == T3_NIC_DATA_SIG)
+ {
+ EeSigFound = TRUE;
+ Value32 = MEM_RD_OFFSET(pDevice, T3_NIC_DATA_NIC_CFG_ADDR);
+
+ /* Determine PHY type. */
+ switch (Value32 & T3_NIC_CFG_PHY_TYPE_MASK)
+ {
+ case T3_NIC_CFG_PHY_TYPE_COPPER:
+ EePhyTypeSerdes = FALSE;
+ break;
+
+ case T3_NIC_CFG_PHY_TYPE_FIBER:
+ EePhyTypeSerdes = TRUE;
+ break;
+
+ default:
+ EePhyTypeSerdes = FALSE;
+ break;
+ }
+
+ /* Determine PHY led mode. */
+ if(T3_ASIC_REV(pDevice->ChipRevId) == T3_ASIC_REV_5700 ||
+ T3_ASIC_REV(pDevice->ChipRevId) == T3_ASIC_REV_5701)
+ {
+ switch(Value32 & T3_NIC_CFG_LED_MODE_MASK)
+ {
+ case T3_NIC_CFG_LED_MODE_TRIPLE_SPEED:
+ EePhyLedMode = LED_MODE_THREE_LINK;
+ break;
+
+ case T3_NIC_CFG_LED_MODE_LINK_SPEED:
+ EePhyLedMode = LED_MODE_LINK10;
+ break;
+
+ default:
+ EePhyLedMode = LED_MODE_AUTO;
+ break;
+ }
+ }
+ else
+ {
+ switch(Value32 & T3_NIC_CFG_LED_MODE_MASK)
+ {
+ case T3_NIC_CFG_LED_MODE_OPEN_DRAIN:
+ EePhyLedMode = LED_MODE_OPEN_DRAIN;
+ break;
+
+ case T3_NIC_CFG_LED_MODE_OUTPUT:
+ EePhyLedMode = LED_MODE_OUTPUT;
+ break;
+
+ default:
+ EePhyLedMode = LED_MODE_AUTO;
+ break;
+ }
+ }
+ if(pDevice->ChipRevId == T3_CHIP_ID_5703_A1 ||
+ pDevice->ChipRevId == T3_CHIP_ID_5703_A2)
+ {
+ /* Enable EEPROM write protection. */
+ if(Value32 & T3_NIC_EEPROM_WP)
+ {
+ pDevice->EepromWp = TRUE;
+ }
+ }
+
+ /* Get the PHY Id. */
+ Value32 = MEM_RD_OFFSET(pDevice, T3_NIC_DATA_PHY_ID_ADDR);
+ if (Value32)
+ {
+ EePhyId = (((Value32 & T3_NIC_PHY_ID1_MASK) >> 16) &
+ PHY_ID1_OUI_MASK) << 10;
+
+ Value32 = Value32 & T3_NIC_PHY_ID2_MASK;
+
+ EePhyId |= ((Value32 & PHY_ID2_OUI_MASK) << 16) |
+ (Value32 & PHY_ID2_MODEL_MASK) | (Value32 & PHY_ID2_REV_MASK);
+ }
+ else
+ {
+ EePhyId = 0;
+ }
+ }
+ else
+ {
+ EeSigFound = FALSE;
+ }
+
+ /* Set the PHY address. */
+ pDevice->PhyAddr = PHY_DEVICE_ID;
+
+ /* Disable auto polling. */
+ pDevice->MiMode = 0xc0000;
+ REG_WR(pDevice, MacCtrl.MiMode, pDevice->MiMode);
+ MM_Wait(40);
+
+ /* Get the PHY id. */
+ LM_ReadPhy(pDevice, PHY_ID1_REG, &Value32);
+ pDevice->PhyId = (Value32 & PHY_ID1_OUI_MASK) << 10;
+
+ LM_ReadPhy(pDevice, PHY_ID2_REG, &Value32);
+ pDevice->PhyId |= ((Value32 & PHY_ID2_OUI_MASK) << 16) |
+ (Value32 & PHY_ID2_MODEL_MASK) | (Value32 & PHY_ID2_REV_MASK);
+
+ /* Set the EnableTbi flag to false if we have a copper PHY. */
+ switch(pDevice->PhyId & PHY_ID_MASK)
+ {
+ case PHY_BCM5400_PHY_ID:
+ pDevice->EnableTbi = FALSE;
+ break;
+
+ case PHY_BCM5401_PHY_ID:
+ pDevice->EnableTbi = FALSE;
+ break;
+
+ case PHY_BCM5411_PHY_ID:
+ pDevice->EnableTbi = FALSE;
+ break;
+
+ case PHY_BCM5701_PHY_ID:
+ pDevice->EnableTbi = FALSE;
+ break;
+
+ case PHY_BCM5703_PHY_ID:
+ pDevice->EnableTbi = FALSE;
+ break;
+
+ case PHY_BCM5704_PHY_ID:
+ pDevice->EnableTbi = FALSE;
+ break;
+
+ case PHY_BCM8002_PHY_ID:
+ pDevice->EnableTbi = TRUE;
+ break;
+
+ default:
+
+ if (pAdapterInfo)
+ {
+ pDevice->PhyId = pAdapterInfo->PhyId;
+ pDevice->EnableTbi = pAdapterInfo->Serdes;
+ }
+ else if (EeSigFound)
+ {
+ pDevice->PhyId = EePhyId;
+ pDevice->EnableTbi = EePhyTypeSerdes;
+ }
+ break;
+ }
+
+ /* Bail out if we don't know the copper PHY id. */
+ if(UNKNOWN_PHY_ID(pDevice->PhyId) && !pDevice->EnableTbi)
+ {
+ return LM_STATUS_FAILURE;
+ }
+
+ if(T3_ASIC_REV(pDevice->ChipRevId) == T3_ASIC_REV_5703)
+ {
+ if((pDevice->SavedCacheLineReg & 0xff00) < 0x4000)
+ {
+ pDevice->SavedCacheLineReg &= 0xffff00ff;
+ pDevice->SavedCacheLineReg |= 0x4000;
+ }
+ }
+ /* Change driver parameters. */
+ Status = MM_GetConfig(pDevice);
+ if(Status != LM_STATUS_SUCCESS)
+ {
+ return Status;
+ }
+
+#if INCLUDE_5701_AX_FIX
+ if (pDevice->ChipRevId == T3_CHIP_ID_5701_A0 ||
+ pDevice->ChipRevId == T3_CHIP_ID_5701_B0)
+ {
+ pDevice->ResetPhyOnInit = TRUE;
+ }
+#endif
+
+ /* Save the current phy link status. */
+ if(!pDevice->EnableTbi)
+ {
+ LM_ReadPhy(pDevice, PHY_STATUS_REG, &Value32);
+ LM_ReadPhy(pDevice, PHY_STATUS_REG, &Value32);
+
+ /* If we don't have link reset the PHY. */
+ if(!(Value32 & PHY_STATUS_LINK_PASS) || pDevice->ResetPhyOnInit)
+ {
+
+ LM_WritePhy(pDevice, PHY_CTRL_REG, PHY_CTRL_PHY_RESET);
+
+ for(j = 0; j < 100; j++)
+ {
+ MM_Wait(10);
+
+ LM_ReadPhy(pDevice, PHY_CTRL_REG, &Value32);
+ if(Value32 && !(Value32 & PHY_CTRL_PHY_RESET))
+ {
+ MM_Wait(40);
+ break;
+ }
+ }
+
+
+#if INCLUDE_5701_AX_FIX
+ /* 5701_AX_BX bug: only advertises 10mb speed. */
+ if(pDevice->ChipRevId == T3_CHIP_ID_5701_A0 ||
+ pDevice->ChipRevId == T3_CHIP_ID_5701_B0)
+ {
+
+ Value32 = PHY_AN_AD_PROTOCOL_802_3_CSMA_CD |
+ PHY_AN_AD_10BASET_HALF | PHY_AN_AD_10BASET_FULL |
+ PHY_AN_AD_100BASETX_FULL | PHY_AN_AD_100BASETX_HALF;
+ Value32 |= GetPhyAdFlowCntrlSettings(pDevice);
+ LM_WritePhy(pDevice, PHY_AN_AD_REG, Value32);
+ pDevice->advertising = Value32;
+
+ Value32 = BCM540X_AN_AD_1000BASET_HALF |
+ BCM540X_AN_AD_1000BASET_FULL | BCM540X_CONFIG_AS_MASTER |
+ BCM540X_ENABLE_CONFIG_AS_MASTER;
+ LM_WritePhy(pDevice, BCM540X_1000BASET_CTRL_REG, Value32);
+ pDevice->advertising1000 = Value32;
+
+ LM_WritePhy(pDevice, PHY_CTRL_REG, PHY_CTRL_AUTO_NEG_ENABLE |
+ PHY_CTRL_RESTART_AUTO_NEG);
+ }
+#endif
+ if(T3_ASIC_REV(pDevice->ChipRevId) == T3_ASIC_REV_5703)
+ {
+ LM_WritePhy(pDevice, 0x18, 0x0c00);
+ LM_WritePhy(pDevice, 0x17, 0x201f);
+ LM_WritePhy(pDevice, 0x15, 0x2aaa);
+ }
+ if(pDevice->ChipRevId == T3_CHIP_ID_5704_A0)
+ {
+ LM_WritePhy(pDevice, 0x1c, 0x8d68);
+ LM_WritePhy(pDevice, 0x1c, 0x8d68);
+ }
+ /* Enable Ethernet@WireSpeed. */
+ if(pDevice->EnableWireSpeed)
+ {
+ LM_WritePhy(pDevice, 0x18, 0x7007);
+ LM_ReadPhy(pDevice, 0x18, &Value32);
+ LM_WritePhy(pDevice, 0x18, Value32 | BIT_15 | BIT_4);
+ }
+ }
+ }
+
+ /* Turn off tap power management. */
+ if((pDevice->PhyId & PHY_ID_MASK) == PHY_BCM5401_PHY_ID)
+ {
+ LM_WritePhy(pDevice, BCM5401_AUX_CTRL, 0x0c20);
+ LM_WritePhy(pDevice, BCM540X_DSP_ADDRESS_REG, 0x0012);
+ LM_WritePhy(pDevice, BCM540X_DSP_RW_PORT, 0x1804);
+ LM_WritePhy(pDevice, BCM540X_DSP_ADDRESS_REG, 0x0013);
+ LM_WritePhy(pDevice, BCM540X_DSP_RW_PORT, 0x1204);
+ LM_WritePhy(pDevice, BCM540X_DSP_ADDRESS_REG, 0x8006);
+ LM_WritePhy(pDevice, BCM540X_DSP_RW_PORT, 0x0132);
+ LM_WritePhy(pDevice, BCM540X_DSP_ADDRESS_REG, 0x8006);
+ LM_WritePhy(pDevice, BCM540X_DSP_RW_PORT, 0x0232);
+ LM_WritePhy(pDevice, BCM540X_DSP_ADDRESS_REG, 0x201f);
+ LM_WritePhy(pDevice, BCM540X_DSP_RW_PORT, 0x0a20);
+
+ MM_Wait(40);
+ }
+
+#if INCLUDE_TBI_SUPPORT
+ pDevice->IgnoreTbiLinkChange = FALSE;
+
+ if(pDevice->EnableTbi)
+ {
+ pDevice->WakeUpModeCap = LM_WAKE_UP_MODE_NONE;
+ pDevice->PhyIntMode = T3_PHY_INT_MODE_LINK_READY;
+ if ((pDevice->PollTbiLink == BAD_DEFAULT_VALUE) ||
+ pDevice->DisableAutoNeg)
+ {
+ pDevice->PollTbiLink = FALSE;
+ }
+ }
+ else
+ {
+ pDevice->PollTbiLink = FALSE;
+ }
+#endif /* INCLUDE_TBI_SUPPORT */
+
+ /* UseTaggedStatus is only valid for 5701 and later. */
+ if (T3_ASIC_REV(pDevice->ChipRevId) == T3_ASIC_REV_5700)
+ {
+ pDevice->UseTaggedStatus = FALSE;
+
+ pDevice->CoalesceMode = 0;
+ }
+ else
+ {
+ pDevice->CoalesceMode = HOST_COALESCE_CLEAR_TICKS_ON_RX_BD_EVENT |
+ HOST_COALESCE_CLEAR_TICKS_ON_TX_BD_EVENT;
+ }
+
+ /* Set the status block size. */
+ if(T3_CHIP_REV(pDevice->ChipRevId) != T3_CHIP_REV_5700_AX &&
+ T3_CHIP_REV(pDevice->ChipRevId) != T3_CHIP_REV_5700_BX)
+ {
+ pDevice->CoalesceMode |= HOST_COALESCE_32_BYTE_STATUS_MODE;
+ }
+
+ /* Check the DURING_INT coalescing ticks parameters. */
+ if(pDevice->UseTaggedStatus)
+ {
+ if(pDevice->RxCoalescingTicksDuringInt == BAD_DEFAULT_VALUE)
+ {
+ pDevice->RxCoalescingTicksDuringInt =
+ DEFAULT_RX_COALESCING_TICKS_DURING_INT;
+ }
+
+ if(pDevice->TxCoalescingTicksDuringInt == BAD_DEFAULT_VALUE)
+ {
+ pDevice->TxCoalescingTicksDuringInt =
+ DEFAULT_TX_COALESCING_TICKS_DURING_INT;
+ }
+
+ if(pDevice->RxMaxCoalescedFramesDuringInt == BAD_DEFAULT_VALUE)
+ {
+ pDevice->RxMaxCoalescedFramesDuringInt =
+ DEFAULT_RX_MAX_COALESCED_FRAMES_DURING_INT;
+ }
+
+ if(pDevice->TxMaxCoalescedFramesDuringInt == BAD_DEFAULT_VALUE)
+ {
+ pDevice->TxMaxCoalescedFramesDuringInt =
+ DEFAULT_TX_MAX_COALESCED_FRAMES_DURING_INT;
+ }
+ }
+ else
+ {
+ if(pDevice->RxCoalescingTicksDuringInt == BAD_DEFAULT_VALUE)
+ {
+ pDevice->RxCoalescingTicksDuringInt = 0;
+ }
+
+ if(pDevice->TxCoalescingTicksDuringInt == BAD_DEFAULT_VALUE)
+ {
+ pDevice->TxCoalescingTicksDuringInt = 0;
+ }
+
+ if(pDevice->RxMaxCoalescedFramesDuringInt == BAD_DEFAULT_VALUE)
+ {
+ pDevice->RxMaxCoalescedFramesDuringInt = 0;
+ }
+
+ if(pDevice->TxMaxCoalescedFramesDuringInt == BAD_DEFAULT_VALUE)
+ {
+ pDevice->TxMaxCoalescedFramesDuringInt = 0;
+ }
+ }
+
+#if T3_JUMBO_RCV_RCB_ENTRY_COUNT
+ if(pDevice->RxMtu <= (MAX_STD_RCV_BUFFER_SIZE - 8 /* CRC */))
+ {
+ pDevice->RxJumboDescCnt = 0;
+ if(pDevice->RxMtu <= MAX_ETHERNET_PACKET_SIZE_NO_CRC)
+ {
+ pDevice->RxMtu = MAX_ETHERNET_PACKET_SIZE_NO_CRC;
+ }
+ }
+ else
+ {
+ pDevice->RxJumboBufferSize = (pDevice->RxMtu + 8 /* CRC + VLAN */ +
+ COMMON_CACHE_LINE_SIZE-1) & ~COMMON_CACHE_LINE_MASK;
+
+ if(pDevice->RxJumboBufferSize > MAX_JUMBO_RCV_BUFFER_SIZE)
+ {
+ pDevice->RxJumboBufferSize = DEFAULT_JUMBO_RCV_BUFFER_SIZE;
+ pDevice->RxMtu = pDevice->RxJumboBufferSize - 8 /* CRC + VLAN */;
+ }
+ pDevice->TxMtu = pDevice->RxMtu;
+
+ }
+#else
+ pDevice->RxMtu = MAX_ETHERNET_PACKET_SIZE_NO_CRC;
+#endif /* T3_JUMBO_RCV_RCB_ENTRY_COUNT */
+
+ pDevice->RxPacketDescCnt =
+#if T3_JUMBO_RCV_RCB_ENTRY_COUNT
+ pDevice->RxJumboDescCnt +
+#endif /* T3_JUMBO_RCV_RCB_ENTRY_COUNT */
+ pDevice->RxStdDescCnt;
+
+ if(pDevice->TxMtu < MAX_ETHERNET_PACKET_SIZE_NO_CRC)
+ {
+ pDevice->TxMtu = MAX_ETHERNET_PACKET_SIZE_NO_CRC;
+ }
+
+ if(pDevice->TxMtu > MAX_JUMBO_TX_BUFFER_SIZE)
+ {
+ pDevice->TxMtu = MAX_JUMBO_TX_BUFFER_SIZE;
+ }
+
+ /* Configure the proper ways to get link change interrupt. */
+ if(pDevice->PhyIntMode == T3_PHY_INT_MODE_AUTO)
+ {
+ if(T3_ASIC_REV(pDevice->ChipRevId) == T3_ASIC_REV_5700)
+ {
+ pDevice->PhyIntMode = T3_PHY_INT_MODE_MI_INTERRUPT;
+ }
+ else
+ {
+ pDevice->PhyIntMode = T3_PHY_INT_MODE_LINK_READY;
+ }
+ }
+ else if(pDevice->PhyIntMode == T3_PHY_INT_MODE_AUTO_POLLING)
+ {
+ /* Auto-polling does not work on 5700_AX and 5700_BX. */
+ if(T3_ASIC_REV(pDevice->ChipRevId) == T3_ASIC_REV_5700)
+ {
+ pDevice->PhyIntMode = T3_PHY_INT_MODE_MI_INTERRUPT;
+ }
+ }
+
+ /* Determine the method to get link change status. */
+ if(pDevice->LinkChngMode == T3_LINK_CHNG_MODE_AUTO)
+ {
+ /* The link status bit in the status block does not work on 5700_AX */
+ /* and 5700_BX chips. */
+ if(T3_ASIC_REV(pDevice->ChipRevId) == T3_ASIC_REV_5700)
+ {
+ pDevice->LinkChngMode = T3_LINK_CHNG_MODE_USE_STATUS_REG;
+ }
+ else
+ {
+ pDevice->LinkChngMode = T3_LINK_CHNG_MODE_USE_STATUS_BLOCK;
+ }
+ }
+
+ if(pDevice->PhyIntMode == T3_PHY_INT_MODE_MI_INTERRUPT ||
+ T3_ASIC_REV(pDevice->ChipRevId) == T3_ASIC_REV_5700)
+ {
+ pDevice->LinkChngMode = T3_LINK_CHNG_MODE_USE_STATUS_REG;
+ }
+
+ /* Configure PHY led mode. */
+ if(pDevice->LedMode == LED_MODE_AUTO)
+ {
+ if(T3_ASIC_REV(pDevice->ChipRevId) == T3_ASIC_REV_5700 ||
+ T3_ASIC_REV(pDevice->ChipRevId) == T3_ASIC_REV_5701)
+ {
+ if(pDevice->SubsystemVendorId == T3_SVID_DELL)
+ {
+ pDevice->LedMode = LED_MODE_LINK10;
+ }
+ else
+ {
+ pDevice->LedMode = LED_MODE_THREE_LINK;
+
+ if(EeSigFound && EePhyLedMode != LED_MODE_AUTO)
+ {
+ pDevice->LedMode = EePhyLedMode;
+ }
+ }
+
+ /* bug? 5701 in LINK10 mode does not seem to work when */
+ /* PhyIntMode is LINK_READY. */
+ if(T3_ASIC_REV(pDevice->ChipRevId) != T3_ASIC_REV_5700 &&
+#if INCLUDE_TBI_SUPPORT
+ pDevice->EnableTbi == FALSE &&
+#endif
+ pDevice->LedMode == LED_MODE_LINK10)
+ {
+ pDevice->PhyIntMode = T3_PHY_INT_MODE_MI_INTERRUPT;
+ pDevice->LinkChngMode = T3_LINK_CHNG_MODE_USE_STATUS_REG;
+ }
+
+ if(pDevice->EnableTbi)
+ {
+ pDevice->LedMode = LED_MODE_THREE_LINK;
+ }
+ }
+ else
+ {
+ if(EeSigFound && EePhyLedMode != LED_MODE_AUTO)
+ {
+ pDevice->LedMode = EePhyLedMode;
+ }
+ else
+ {
+ pDevice->LedMode = LED_MODE_OPEN_DRAIN;
+ }
+ }
+ }
+
+ /* Enable OneDmaAtOnce. */
+ if(pDevice->OneDmaAtOnce == BAD_DEFAULT_VALUE)
+ {
+ pDevice->OneDmaAtOnce = FALSE;
+ }
+
+ if (T3_ASIC_REV(pDevice->ChipRevId) == T3_ASIC_REV_5700 ||
+ pDevice->ChipRevId == T3_CHIP_ID_5701_A0 ||
+ pDevice->ChipRevId == T3_CHIP_ID_5701_B0 ||
+ pDevice->ChipRevId == T3_CHIP_ID_5701_B2)
+ {
+ pDevice->WolSpeed = WOL_SPEED_10MB;
+ }
+ else
+ {
+ pDevice->WolSpeed = WOL_SPEED_100MB;
+ }
+
+ /* Offloadings. */
+ pDevice->TaskToOffload = LM_TASK_OFFLOAD_NONE;
+
+ /* Turn off task offloading on Ax. */
+ if(pDevice->ChipRevId == T3_CHIP_ID_5700_B0)
+ {
+ pDevice->TaskOffloadCap &= ~(LM_TASK_OFFLOAD_TX_TCP_CHECKSUM |
+ LM_TASK_OFFLOAD_TX_UDP_CHECKSUM);
+ }
+ pDevice->PciState = REG_RD(pDevice, PciCfg.PciState);
+ LM_ReadVPD(pDevice);
+ LM_ReadBootCodeVersion(pDevice);
+ LM_GetBusSpeed(pDevice);
+
+ return LM_STATUS_SUCCESS;
+} /* LM_GetAdapterInfo */
+
+STATIC PLM_ADAPTER_INFO
+LM_GetAdapterInfoBySsid(
+ LM_UINT16 Svid,
+ LM_UINT16 Ssid)
+{
+ static LM_ADAPTER_INFO AdapterArr[] =
+ {
+ { T3_SVID_BROADCOM, T3_SSID_BROADCOM_BCM95700A6, PHY_BCM5401_PHY_ID, 0},
+ { T3_SVID_BROADCOM, T3_SSID_BROADCOM_BCM95701A5, PHY_BCM5701_PHY_ID, 0},
+ { T3_SVID_BROADCOM, T3_SSID_BROADCOM_BCM95700T6, PHY_BCM8002_PHY_ID, 1},
+ { T3_SVID_BROADCOM, T3_SSID_BROADCOM_BCM95700A9, 0, 1 },
+ { T3_SVID_BROADCOM, T3_SSID_BROADCOM_BCM95701T1, PHY_BCM5701_PHY_ID, 0},
+ { T3_SVID_BROADCOM, T3_SSID_BROADCOM_BCM95701T8, PHY_BCM5701_PHY_ID, 0},
+ { T3_SVID_BROADCOM, T3_SSID_BROADCOM_BCM95701A7, 0, 1},
+ { T3_SVID_BROADCOM, T3_SSID_BROADCOM_BCM95701A10, PHY_BCM5701_PHY_ID, 0},
+ { T3_SVID_BROADCOM, T3_SSID_BROADCOM_BCM95701A12, PHY_BCM5701_PHY_ID, 0},
+ { T3_SVID_BROADCOM, T3_SSID_BROADCOM_BCM95703Ax1, PHY_BCM5701_PHY_ID, 0},
+ { T3_SVID_BROADCOM, T3_SSID_BROADCOM_BCM95703Ax2, PHY_BCM5701_PHY_ID, 0},
+
+ { T3_SVID_3COM, T3_SSID_3COM_3C996T, PHY_BCM5401_PHY_ID, 0 },
+ { T3_SVID_3COM, T3_SSID_3COM_3C996BT, PHY_BCM5701_PHY_ID, 0 },
+ { T3_SVID_3COM, T3_SSID_3COM_3C996SX, 0, 1 },
+ { T3_SVID_3COM, T3_SSID_3COM_3C1000T, PHY_BCM5701_PHY_ID, 0 },
+ { T3_SVID_3COM, T3_SSID_3COM_3C940BR01, PHY_BCM5701_PHY_ID, 0 },
+
+ { T3_SVID_DELL, T3_SSID_DELL_VIPER, PHY_BCM5401_PHY_ID, 0 },
+ { T3_SVID_DELL, T3_SSID_DELL_JAGUAR, PHY_BCM5401_PHY_ID, 0 },
+ { T3_SVID_DELL, T3_SSID_DELL_MERLOT, PHY_BCM5411_PHY_ID, 0 },
+ { T3_SVID_DELL, T3_SSID_DELL_SLIM_MERLOT, PHY_BCM5411_PHY_ID, 0 },
+
+ { T3_SVID_COMPAQ, T3_SSID_COMPAQ_BANSHEE, PHY_BCM5701_PHY_ID, 0 },
+ { T3_SVID_COMPAQ, T3_SSID_COMPAQ_BANSHEE_2, PHY_BCM5701_PHY_ID, 0 },
+ { T3_SVID_COMPAQ, T3_SSID_COMPAQ_CHANGELING, 0, 1 },
+ { T3_SVID_COMPAQ, T3_SSID_COMPAQ_NC7780, PHY_BCM5701_PHY_ID, 0 },
+ { T3_SVID_COMPAQ, T3_SSID_COMPAQ_NC7780_2, PHY_BCM5701_PHY_ID, 0 },
+
+ };
+ LM_UINT32 j;
+
+ for(j = 0; j < sizeof(AdapterArr)/sizeof(LM_ADAPTER_INFO); j++)
+ {
+ if(AdapterArr[j].Svid == Svid && AdapterArr[j].Ssid == Ssid)
+ {
+ return &AdapterArr[j];
+ }
+ }
+
+ return NULL;
+}
+
+
+/******************************************************************************/
+/* Description: */
+/* This routine sets up receive/transmit buffer descriptions queues. */
+/* */
+/* Return: */
+/* LM_STATUS_SUCCESS */
+/******************************************************************************/
+LM_STATUS
+LM_InitializeAdapter(
+PLM_DEVICE_BLOCK pDevice)
+{
+ LM_PHYSICAL_ADDRESS MemPhy;
+ PLM_UINT8 pMemVirt;
+ PLM_PACKET pPacket;
+ LM_STATUS Status;
+ LM_UINT32 Size;
+ LM_UINT32 j;
+
+ /* Set power state to D0. */
+ LM_SetPowerState(pDevice, LM_POWER_STATE_D0);
+
+ /* Intialize the queues. */
+ QQ_InitQueue(&pDevice->RxPacketReceivedQ.Container,
+ MAX_RX_PACKET_DESC_COUNT);
+ QQ_InitQueue(&pDevice->RxPacketFreeQ.Container,
+ MAX_RX_PACKET_DESC_COUNT);
+
+ QQ_InitQueue(&pDevice->TxPacketFreeQ.Container,MAX_TX_PACKET_DESC_COUNT);
+ QQ_InitQueue(&pDevice->TxPacketActiveQ.Container,MAX_TX_PACKET_DESC_COUNT);
+ QQ_InitQueue(&pDevice->TxPacketXmittedQ.Container,MAX_TX_PACKET_DESC_COUNT);
+
+ /* Allocate shared memory for: status block, the buffers for receive */
+ /* rings -- standard, mini, jumbo, and return rings. */
+ Size = T3_STATUS_BLOCK_SIZE + sizeof(T3_STATS_BLOCK) +
+ T3_STD_RCV_RCB_ENTRY_COUNT * sizeof(T3_RCV_BD) +
+#if T3_JUMBO_RCV_RCB_ENTRY_COUNT
+ T3_JUMBO_RCV_RCB_ENTRY_COUNT * sizeof(T3_RCV_BD) +
+#endif /* T3_JUMBO_RCV_RCB_ENTRY_COUNT */
+ T3_RCV_RETURN_RCB_ENTRY_COUNT * sizeof(T3_RCV_BD);
+
+ /* Memory for host based Send BD. */
+ if(pDevice->NicSendBd == FALSE)
+ {
+ Size += sizeof(T3_SND_BD) * T3_SEND_RCB_ENTRY_COUNT;
+ }
+
+ /* Allocate the memory block. */
+ Status = MM_AllocateSharedMemory(pDevice, Size, (PLM_VOID) &pMemVirt, &MemPhy, FALSE);
+ if(Status != LM_STATUS_SUCCESS)
+ {
+ return Status;
+ }
+
+ /* Program DMA Read/Write */
+ if (pDevice->PciState & T3_PCI_STATE_NOT_PCI_X_BUS)
+ {
+ pDevice->DmaReadWriteCtrl = 0x763f000f;
+ }
+ else
+ {
+ if(T3_ASIC_REV(pDevice->ChipRevId) == T3_ASIC_REV_5704)
+ {
+ pDevice->DmaReadWriteCtrl = 0x761f0000;
+ }
+ else
+ {
+ pDevice->DmaReadWriteCtrl = 0x761b000f;
+ }
+ if(pDevice->ChipRevId == T3_CHIP_ID_5703_A1 ||
+ pDevice->ChipRevId == T3_CHIP_ID_5703_A2)
+ {
+ pDevice->OneDmaAtOnce = TRUE;
+ }
+ }
+ if(T3_ASIC_REV(pDevice->ChipRevId) == T3_ASIC_REV_5703)
+ {
+ pDevice->DmaReadWriteCtrl &= 0xfffffff0;
+ }
+
+ if(pDevice->OneDmaAtOnce)
+ {
+ pDevice->DmaReadWriteCtrl |= DMA_CTRL_WRITE_ONE_DMA_AT_ONCE;
+ }
+ REG_WR(pDevice, PciCfg.DmaReadWriteCtrl, pDevice->DmaReadWriteCtrl);
+
+ if (LM_DmaTest(pDevice, pMemVirt, MemPhy, 0x400) != LM_STATUS_SUCCESS)
+ {
+ return LM_STATUS_FAILURE;
+ }
+
+ /* Status block. */
+ pDevice->pStatusBlkVirt = (PT3_STATUS_BLOCK) pMemVirt;
+ pDevice->StatusBlkPhy = MemPhy;
+ pMemVirt += T3_STATUS_BLOCK_SIZE;
+ LM_INC_PHYSICAL_ADDRESS(&MemPhy, T3_STATUS_BLOCK_SIZE);
+
+ /* Statistics block. */
+ pDevice->pStatsBlkVirt = (PT3_STATS_BLOCK) pMemVirt;
+ pDevice->StatsBlkPhy = MemPhy;
+ pMemVirt += sizeof(T3_STATS_BLOCK);
+ LM_INC_PHYSICAL_ADDRESS(&MemPhy, sizeof(T3_STATS_BLOCK));
+
+ /* Receive standard BD buffer. */
+ pDevice->pRxStdBdVirt = (PT3_RCV_BD) pMemVirt;
+ pDevice->RxStdBdPhy = MemPhy;
+
+ pMemVirt += T3_STD_RCV_RCB_ENTRY_COUNT * sizeof(T3_RCV_BD);
+ LM_INC_PHYSICAL_ADDRESS(&MemPhy,
+ T3_STD_RCV_RCB_ENTRY_COUNT * sizeof(T3_RCV_BD));
+
+#if T3_JUMBO_RCV_RCB_ENTRY_COUNT
+ /* Receive jumbo BD buffer. */
+ pDevice->pRxJumboBdVirt = (PT3_RCV_BD) pMemVirt;
+ pDevice->RxJumboBdPhy = MemPhy;
+
+ pMemVirt += T3_JUMBO_RCV_RCB_ENTRY_COUNT * sizeof(T3_RCV_BD);
+ LM_INC_PHYSICAL_ADDRESS(&MemPhy,
+ T3_JUMBO_RCV_RCB_ENTRY_COUNT * sizeof(T3_RCV_BD));
+#endif /* T3_JUMBO_RCV_RCB_ENTRY_COUNT */
+
+ /* Receive return BD buffer. */
+ pDevice->pRcvRetBdVirt = (PT3_RCV_BD) pMemVirt;
+ pDevice->RcvRetBdPhy = MemPhy;
+
+ pMemVirt += T3_RCV_RETURN_RCB_ENTRY_COUNT * sizeof(T3_RCV_BD);
+ LM_INC_PHYSICAL_ADDRESS(&MemPhy,
+ T3_RCV_RETURN_RCB_ENTRY_COUNT * sizeof(T3_RCV_BD));
+
+ /* Set up Send BD. */
+ if(pDevice->NicSendBd == FALSE)
+ {
+ pDevice->pSendBdVirt = (PT3_SND_BD) pMemVirt;
+ pDevice->SendBdPhy = MemPhy;
+
+ pMemVirt += sizeof(T3_SND_BD) * T3_SEND_RCB_ENTRY_COUNT;
+ LM_INC_PHYSICAL_ADDRESS(&MemPhy,
+ sizeof(T3_SND_BD) * T3_SEND_RCB_ENTRY_COUNT);
+ }
+ else
+ {
+ pDevice->pSendBdVirt = (PT3_SND_BD)
+ pDevice->pMemView->uIntMem.First32k.BufferDesc;
+ pDevice->SendBdPhy.High = 0;
+ pDevice->SendBdPhy.Low = T3_NIC_SND_BUFFER_DESC_ADDR;
+ }
+
+ /* Allocate memory for packet descriptors. */
+ Size = (pDevice->RxPacketDescCnt +
+ pDevice->TxPacketDescCnt) * MM_PACKET_DESC_SIZE;
+ Status = MM_AllocateMemory(pDevice, Size, (PLM_VOID *) &pPacket);
+ if(Status != LM_STATUS_SUCCESS)
+ {
+ return Status;
+ }
+ pDevice->pPacketDescBase = (PLM_VOID) pPacket;
+
+ /* Create transmit packet descriptors from the memory block and add them */
+ /* to the TxPacketFreeQ for each send ring. */
+ for(j = 0; j < pDevice->TxPacketDescCnt; j++)
+ {
+ /* Ring index. */
+ pPacket->Flags = 0;
+
+ /* Queue the descriptor in the TxPacketFreeQ of the 'k' ring. */
+ QQ_PushTail(&pDevice->TxPacketFreeQ.Container, pPacket);
+
+ /* Get the pointer to the next descriptor. MM_PACKET_DESC_SIZE */
+ /* is the total size of the packet descriptor including the */
+ /* os-specific extensions in the UM_PACKET structure. */
+ pPacket = (PLM_PACKET) ((PLM_UINT8) pPacket + MM_PACKET_DESC_SIZE);
+ } /* for(j.. */
+
+ /* Create receive packet descriptors from the memory block and add them */
+ /* to the RxPacketFreeQ. Create the Standard packet descriptors. */
+ for(j = 0; j < pDevice->RxStdDescCnt; j++)
+ {
+ /* Receive producer ring. */
+ pPacket->u.Rx.RcvProdRing = T3_STD_RCV_PROD_RING;
+
+ /* Receive buffer size. */
+ pPacket->u.Rx.RxBufferSize = MAX_STD_RCV_BUFFER_SIZE;
+
+ /* Add the descriptor to RxPacketFreeQ. */
+ QQ_PushTail(&pDevice->RxPacketFreeQ.Container, pPacket);
+
+ /* Get the pointer to the next descriptor. MM_PACKET_DESC_SIZE */
+ /* is the total size of the packet descriptor including the */
+ /* os-specific extensions in the UM_PACKET structure. */
+ pPacket = (PLM_PACKET) ((PLM_UINT8) pPacket + MM_PACKET_DESC_SIZE);
+ } /* for */
+
+#if T3_JUMBO_RCV_RCB_ENTRY_COUNT
+ /* Create the Jumbo packet descriptors. */
+ for(j = 0; j < pDevice->RxJumboDescCnt; j++)
+ {
+ /* Receive producer ring. */
+ pPacket->u.Rx.RcvProdRing = T3_JUMBO_RCV_PROD_RING;
+
+ /* Receive buffer size. */
+ pPacket->u.Rx.RxBufferSize = pDevice->RxJumboBufferSize;
+
+ /* Add the descriptor to RxPacketFreeQ. */
+ QQ_PushTail(&pDevice->RxPacketFreeQ.Container, pPacket);
+
+ /* Get the pointer to the next descriptor. MM_PACKET_DESC_SIZE */
+ /* is the total size of the packet descriptor including the */
+ /* os-specific extensions in the UM_PACKET structure. */
+ pPacket = (PLM_PACKET) ((PLM_UINT8) pPacket + MM_PACKET_DESC_SIZE);
+ } /* for */
+#endif /* T3_JUMBO_RCV_RCB_ENTRY_COUNT */
+
+ /* Initialize the rest of the packet descriptors. */
+ Status = MM_InitializeUmPackets(pDevice);
+ if(Status != LM_STATUS_SUCCESS)
+ {
+ return Status;
+ } /* if */
+
+ /* Default receive mask. */
+ pDevice->ReceiveMask = LM_ACCEPT_MULTICAST | LM_ACCEPT_BROADCAST |
+ LM_ACCEPT_UNICAST;
+
+ /* Make sure we are in the first 32k memory window or NicSendBd. */
+ REG_WR(pDevice, PciCfg.MemWindowBaseAddr, 0);
+
+ /* Initialize the hardware. */
+ Status = LM_ResetAdapter(pDevice);
+ if(Status != LM_STATUS_SUCCESS)
+ {
+ return Status;
+ }
+
+ /* We are done with initialization. */
+ pDevice->InitDone = TRUE;
+
+ return LM_STATUS_SUCCESS;
+} /* LM_InitializeAdapter */
+
+
+
+/******************************************************************************/
+/* Description: */
+/* This function Enables/Disables a given block. */
+/* */
+/* Return: */
+/* LM_STATUS_SUCCESS */
+/******************************************************************************/
+LM_STATUS
+LM_CntrlBlock(
+PLM_DEVICE_BLOCK pDevice,
+LM_UINT32 mask,LM_UINT32 cntrl)
+{
+ LM_UINT32 j,i,data;
+ LM_UINT32 MaxWaitCnt;
+
+ MaxWaitCnt = 2;
+ j = 0;
+
+ for(i = 0 ; i < 32; i++)
+ {
+ if(!(mask & (1 << i)))
+ continue;
+
+ switch (1 << i)
+ {
+ case T3_BLOCK_DMA_RD:
+ data = REG_RD(pDevice, DmaRead.Mode);
+ if (cntrl == LM_DISABLE)
+ {
+ data &= ~DMA_READ_MODE_ENABLE;
+ REG_WR(pDevice, DmaRead.Mode, data);
+ for(j = 0; j < MaxWaitCnt; j++)
+ {
+ if(!(REG_RD(pDevice, DmaRead.Mode) & DMA_READ_MODE_ENABLE))
+ break;
+ MM_Wait(10);
+ }
+ }
+ else
+ REG_WR(pDevice, DmaRead.Mode, data | DMA_READ_MODE_ENABLE);
+ break;
+
+ case T3_BLOCK_DMA_COMP:
+ data = REG_RD(pDevice,DmaComp.Mode);
+ if (cntrl == LM_DISABLE)
+ {
+ data &= ~DMA_COMP_MODE_ENABLE;
+ REG_WR(pDevice, DmaComp.Mode, data);
+ for(j = 0; j < MaxWaitCnt; j++)
+ {
+ if(!(REG_RD(pDevice, DmaComp.Mode) & DMA_COMP_MODE_ENABLE))
+ break;
+ MM_Wait(10);
+ }
+ }
+ else
+ REG_WR(pDevice, DmaComp.Mode, data | DMA_COMP_MODE_ENABLE);
+ break;
+
+ case T3_BLOCK_RX_BD_INITIATOR:
+ data = REG_RD(pDevice, RcvBdIn.Mode);
+ if (cntrl == LM_DISABLE)
+ {
+ data &= ~RCV_BD_IN_MODE_ENABLE;
+ REG_WR(pDevice, RcvBdIn.Mode,data);
+ for(j = 0; j < MaxWaitCnt; j++)
+ {
+ if(!(REG_RD(pDevice, RcvBdIn.Mode) & RCV_BD_IN_MODE_ENABLE))
+ break;
+ MM_Wait(10);
+ }
+ }
+ else
+ REG_WR(pDevice, RcvBdIn.Mode,data | RCV_BD_IN_MODE_ENABLE);
+ break;
+
+ case T3_BLOCK_RX_BD_COMP:
+ data = REG_RD(pDevice, RcvBdComp.Mode);
+ if (cntrl == LM_DISABLE)
+ {
+ data &= ~RCV_BD_COMP_MODE_ENABLE;
+ REG_WR(pDevice, RcvBdComp.Mode,data);
+ for(j = 0; j < MaxWaitCnt; j++)
+ {
+ if(!(REG_RD(pDevice, RcvBdComp.Mode) & RCV_BD_COMP_MODE_ENABLE))
+ break;
+ MM_Wait(10);
+ }
+ }
+ else
+ REG_WR(pDevice, RcvBdComp.Mode,data | RCV_BD_COMP_MODE_ENABLE);
+ break;
+
+ case T3_BLOCK_DMA_WR:
+ data = REG_RD(pDevice, DmaWrite.Mode);
+ if (cntrl == LM_DISABLE)
+ {
+ data &= ~DMA_WRITE_MODE_ENABLE;
+ REG_WR(pDevice, DmaWrite.Mode,data);
+
+ for(j = 0; j < MaxWaitCnt; j++)
+ {
+ if(!(REG_RD(pDevice, DmaWrite.Mode) & DMA_WRITE_MODE_ENABLE))
+ break;
+ MM_Wait(10);
+ }
+ }
+ else
+ REG_WR(pDevice, DmaWrite.Mode,data | DMA_WRITE_MODE_ENABLE);
+ break;
+
+ case T3_BLOCK_MSI_HANDLER:
+ data = REG_RD(pDevice, Msi.Mode);
+ if (cntrl == LM_DISABLE)
+ {
+ data &= ~MSI_MODE_ENABLE;
+ REG_WR(pDevice, Msi.Mode, data);
+ for(j = 0; j < MaxWaitCnt; j++)
+ {
+ if(!(REG_RD(pDevice, Msi.Mode) & MSI_MODE_ENABLE))
+ break;
+ MM_Wait(10);
+ }
+ }
+ else
+ REG_WR(pDevice, Msi.Mode, data |MSI_MODE_ENABLE);
+ break;
+
+ case T3_BLOCK_RX_LIST_PLMT:
+ data = REG_RD(pDevice, RcvListPlmt.Mode);
+ if (cntrl == LM_DISABLE)
+ {
+ data &= ~RCV_LIST_PLMT_MODE_ENABLE;
+ REG_WR(pDevice, RcvListPlmt.Mode,data);
+ for(j = 0; j < MaxWaitCnt; j++)
+ {
+ if(!(REG_RD(pDevice, RcvListPlmt.Mode) & RCV_LIST_PLMT_MODE_ENABLE))
+ break;
+ MM_Wait(10);
+ }
+ }
+ else
+ REG_WR(pDevice, RcvListPlmt.Mode,data | RCV_LIST_PLMT_MODE_ENABLE);
+ break;
+
+ case T3_BLOCK_RX_LIST_SELECTOR:
+ data = REG_RD(pDevice, RcvListSel.Mode);
+ if (cntrl == LM_DISABLE)
+ {
+ data &= ~RCV_LIST_SEL_MODE_ENABLE;
+ REG_WR(pDevice, RcvListSel.Mode,data);
+ for(j = 0; j < MaxWaitCnt; j++)
+ {
+ if(!(REG_RD(pDevice, RcvListSel.Mode) & RCV_LIST_SEL_MODE_ENABLE))
+ break;
+ MM_Wait(10);
+ }
+ }
+ else
+ REG_WR(pDevice, RcvListSel.Mode,data |RCV_LIST_SEL_MODE_ENABLE);
+ break;
+
+ case T3_BLOCK_RX_DATA_INITIATOR:
+ data = REG_RD(pDevice, RcvDataBdIn.Mode);
+ if (cntrl == LM_DISABLE)
+ {
+ data &= ~RCV_DATA_BD_IN_MODE_ENABLE;
+ REG_WR(pDevice, RcvDataBdIn.Mode,data);
+ for(j = 0; j < MaxWaitCnt; j++)
+ {
+ if(!(REG_RD(pDevice, RcvDataBdIn.Mode) & RCV_DATA_BD_IN_MODE_ENABLE))
+ break;
+ MM_Wait(10);
+ }
+ }
+ else
+ REG_WR(pDevice, RcvDataBdIn.Mode, data | RCV_DATA_BD_IN_MODE_ENABLE);
+ break;
+
+ case T3_BLOCK_RX_DATA_COMP:
+ data = REG_RD(pDevice, RcvDataComp.Mode);
+ if (cntrl == LM_DISABLE)
+ {
+ data &= ~RCV_DATA_COMP_MODE_ENABLE;
+ REG_WR(pDevice, RcvDataComp.Mode,data);
+ for(j = 0; j < MaxWaitCnt; j++)
+ {
+ if(!(REG_RD(pDevice, RcvDataBdIn.Mode) & RCV_DATA_COMP_MODE_ENABLE))
+ break;
+ MM_Wait(10);
+ }
+ }
+ else
+ REG_WR(pDevice, RcvDataComp.Mode,data | RCV_DATA_COMP_MODE_ENABLE);
+ break;
+
+ case T3_BLOCK_HOST_COALESING:
+ data = REG_RD(pDevice, HostCoalesce.Mode);
+ if (cntrl == LM_DISABLE)
+ {
+ data &= ~HOST_COALESCE_ENABLE;
+ REG_WR(pDevice, HostCoalesce.Mode, data);
+ for(j = 0; j < MaxWaitCnt; j++)
+ {
+ if(!(REG_RD(pDevice, SndBdIn.Mode) & HOST_COALESCE_ENABLE))
+ break;
+ MM_Wait(10);
+ }
+ }
+ else
+ REG_WR(pDevice, HostCoalesce.Mode, data | HOST_COALESCE_ENABLE);
+ break;
+
+ case T3_BLOCK_MAC_RX_ENGINE:
+ if(cntrl == LM_DISABLE)
+ {
+ pDevice->RxMode &= ~RX_MODE_ENABLE;
+ REG_WR(pDevice, MacCtrl.RxMode, pDevice->RxMode);
+ for(j = 0; j < MaxWaitCnt; j++)
+ {
+ if(!(REG_RD(pDevice, MacCtrl.RxMode) & RX_MODE_ENABLE))
+ {
+ break;
+ }
+ MM_Wait(10);
+ }
+ }
+ else
+ {
+ pDevice->RxMode |= RX_MODE_ENABLE;
+ REG_WR(pDevice, MacCtrl.RxMode, pDevice->RxMode);
+ }
+ break;
+
+ case T3_BLOCK_MBUF_CLUSTER_FREE:
+ data = REG_RD(pDevice, MbufClusterFree.Mode);
+ if (cntrl == LM_DISABLE)
+ {
+ data &= ~MBUF_CLUSTER_FREE_MODE_ENABLE;
+ REG_WR(pDevice, MbufClusterFree.Mode,data);
+ for(j = 0; j < MaxWaitCnt; j++)
+ {
+ if(!(REG_RD(pDevice, MbufClusterFree.Mode) & MBUF_CLUSTER_FREE_MODE_ENABLE))
+ break;
+ MM_Wait(10);
+ }
+ }
+ else
+ REG_WR(pDevice, MbufClusterFree.Mode, data | MBUF_CLUSTER_FREE_MODE_ENABLE);
+ break;
+
+ case T3_BLOCK_SEND_BD_INITIATOR:
+ data = REG_RD(pDevice, SndBdIn.Mode);
+ if (cntrl == LM_DISABLE)
+ {
+ data &= ~SND_BD_IN_MODE_ENABLE;
+ REG_WR(pDevice, SndBdIn.Mode, data);
+ for(j = 0; j < MaxWaitCnt; j++)
+ {
+ if(!(REG_RD(pDevice, SndBdIn.Mode) & SND_BD_IN_MODE_ENABLE))
+ break;
+ MM_Wait(10);
+ }
+ }
+ else
+ REG_WR(pDevice, SndBdIn.Mode, data | SND_BD_IN_MODE_ENABLE);
+ break;
+
+ case T3_BLOCK_SEND_BD_COMP:
+ data = REG_RD(pDevice, SndBdComp.Mode);
+ if (cntrl == LM_DISABLE)
+ {
+ data &= ~SND_BD_COMP_MODE_ENABLE;
+ REG_WR(pDevice, SndBdComp.Mode, data);
+ for(j = 0; j < MaxWaitCnt; j++)
+ {
+ if(!(REG_RD(pDevice, SndBdComp.Mode) & SND_BD_COMP_MODE_ENABLE))
+ break;
+ MM_Wait(10);
+ }
+ }
+ else
+ REG_WR(pDevice, SndBdComp.Mode, data | SND_BD_COMP_MODE_ENABLE);
+ break;
+
+ case T3_BLOCK_SEND_BD_SELECTOR:
+ data = REG_RD(pDevice, SndBdSel.Mode);
+ if (cntrl == LM_DISABLE)
+ {
+ data &= ~SND_BD_SEL_MODE_ENABLE;
+ REG_WR(pDevice, SndBdSel.Mode, data);
+ for(j = 0; j < MaxWaitCnt; j++)
+ {
+ if(!(REG_RD(pDevice, SndBdSel.Mode) & SND_BD_SEL_MODE_ENABLE))
+ break;
+ MM_Wait(10);
+ }
+ }
+ else
+ REG_WR(pDevice, SndBdSel.Mode, data | SND_BD_SEL_MODE_ENABLE);
+ break;
+
+ case T3_BLOCK_SEND_DATA_INITIATOR:
+ data = REG_RD(pDevice, SndDataIn.Mode);
+ if (cntrl == LM_DISABLE)
+ {
+ data &= ~T3_SND_DATA_IN_MODE_ENABLE;
+ REG_WR(pDevice, SndDataIn.Mode,data);
+ for(j = 0; j < MaxWaitCnt; j++)
+ {
+ if(!(REG_RD(pDevice, SndDataIn.Mode) & T3_SND_DATA_IN_MODE_ENABLE))
+ break;
+ MM_Wait(10);
+ }
+ }
+ else
+ REG_WR(pDevice, SndDataIn.Mode,data | T3_SND_DATA_IN_MODE_ENABLE);
+ break;
+
+ case T3_BLOCK_SEND_DATA_COMP:
+ data = REG_RD(pDevice, SndDataComp.Mode);
+ if (cntrl == LM_DISABLE)
+ {
+ data &= ~SND_DATA_COMP_MODE_ENABLE;
+ REG_WR(pDevice, SndDataComp.Mode, data);
+ for(j = 0; j < MaxWaitCnt; j++)
+ {
+ if(!(REG_RD(pDevice, SndDataComp.Mode) & SND_DATA_COMP_MODE_ENABLE))
+ break;
+ MM_Wait(10);
+ }
+ }
+ else
+ REG_WR(pDevice, SndDataComp.Mode,data | SND_DATA_COMP_MODE_ENABLE);
+ break;
+
+ case T3_BLOCK_MAC_TX_ENGINE:
+ if(cntrl == LM_DISABLE)
+ {
+ pDevice->TxMode &= ~TX_MODE_ENABLE;
+ REG_WR(pDevice, MacCtrl.TxMode, pDevice->TxMode);
+ for(j = 0; j < MaxWaitCnt; j++)
+ {
+ if(!(REG_RD(pDevice, MacCtrl.TxMode) & TX_MODE_ENABLE))
+ break;
+ MM_Wait(10);
+ }
+ }
+ else
+ {
+ pDevice->TxMode |= TX_MODE_ENABLE;
+ REG_WR(pDevice, MacCtrl.TxMode, pDevice->TxMode);
+ }
+ break;
+
+ case T3_BLOCK_MEM_ARBITOR:
+ data = REG_RD(pDevice, MemArbiter.Mode);
+ if (cntrl == LM_DISABLE)
+ {
+ data &= ~T3_MEM_ARBITER_MODE_ENABLE;
+ REG_WR(pDevice, MemArbiter.Mode, data);
+ for(j = 0; j < MaxWaitCnt; j++)
+ {
+ if(!(REG_RD(pDevice, MemArbiter.Mode) & T3_MEM_ARBITER_MODE_ENABLE))
+ break;
+ MM_Wait(10);
+ }
+ }
+ else
+ REG_WR(pDevice, MemArbiter.Mode,data|T3_MEM_ARBITER_MODE_ENABLE);
+ break;
+
+ case T3_BLOCK_MBUF_MANAGER:
+ data = REG_RD(pDevice, BufMgr.Mode);
+ if (cntrl == LM_DISABLE)
+ {
+ data &= ~BUFMGR_MODE_ENABLE;
+ REG_WR(pDevice, BufMgr.Mode,data);
+ for(j = 0; j < MaxWaitCnt; j++)
+ {
+ if(!(REG_RD(pDevice, BufMgr.Mode) & BUFMGR_MODE_ENABLE))
+ break;
+ MM_Wait(10);
+ }
+ }
+ else
+ REG_WR(pDevice, BufMgr.Mode,data | BUFMGR_MODE_ENABLE);
+ break;
+
+ case T3_BLOCK_MAC_GLOBAL:
+ if(cntrl == LM_DISABLE)
+ {
+ pDevice->MacMode &= ~(MAC_MODE_ENABLE_TDE |
+ MAC_MODE_ENABLE_RDE |
+ MAC_MODE_ENABLE_FHDE);
+ }
+ else
+ {
+ pDevice->MacMode |= (MAC_MODE_ENABLE_TDE |
+ MAC_MODE_ENABLE_RDE |
+ MAC_MODE_ENABLE_FHDE);
+ }
+ REG_WR(pDevice, MacCtrl.Mode, pDevice->MacMode);
+ break;
+
+ default:
+ return LM_STATUS_FAILURE;
+ } /* switch */
+
+ if(j >= MaxWaitCnt)
+ {
+ return LM_STATUS_FAILURE;
+ }
+ }
+
+ return LM_STATUS_SUCCESS;
+}
+
+/******************************************************************************/
+/* Description: */
+/* This function reinitializes the adapter. */
+/* */
+/* Return: */
+/* LM_STATUS_SUCCESS */
+/******************************************************************************/
+LM_STATUS
+LM_ResetAdapter(
+PLM_DEVICE_BLOCK pDevice)
+{
+ LM_UINT32 Value32;
+ LM_UINT16 Value16;
+ LM_UINT32 j, k;
+
+ /* Disable interrupt. */
+ LM_DisableInterrupt(pDevice);
+
+ /* May get a spurious interrupt */
+ pDevice->pStatusBlkVirt->Status = STATUS_BLOCK_UPDATED;
+
+ /* Disable transmit and receive DMA engines. Abort all pending requests. */
+ if(pDevice->InitDone)
+ {
+ LM_Abort(pDevice);
+ }
+
+ pDevice->ShuttingDown = FALSE;
+
+ LM_ResetChip(pDevice);
+
+ /* Bug: Athlon fix for B3 silicon only. This bit does not do anything */
+ /* in other chip revisions. */
+ if(pDevice->DelayPciGrant)
+ {
+ Value32 = REG_RD(pDevice, PciCfg.ClockCtrl);
+ REG_WR(pDevice, PciCfg.ClockCtrl, Value32 | BIT_31);
+ }
+
+ if(pDevice->ChipRevId == T3_CHIP_ID_5704_A0)
+ {
+ if (!(pDevice->PciState & T3_PCI_STATE_CONVENTIONAL_PCI_MODE))
+ {
+ Value32 = REG_RD(pDevice, PciCfg.PciState);
+ Value32 |= T3_PCI_STATE_RETRY_SAME_DMA;
+ REG_WR(pDevice, PciCfg.PciState, Value32);
+ }
+ }
+
+ /* Enable TaggedStatus mode. */
+ if(pDevice->UseTaggedStatus)
+ {
+ pDevice->MiscHostCtrl |= MISC_HOST_CTRL_ENABLE_TAGGED_STATUS_MODE;
+ }
+
+ /* Restore PCI configuration registers. */
+ MM_WriteConfig32(pDevice, PCI_CACHE_LINE_SIZE_REG,
+ pDevice->SavedCacheLineReg);
+ MM_WriteConfig32(pDevice, PCI_SUBSYSTEM_VENDOR_ID_REG,
+ (pDevice->SubsystemId << 16) | pDevice->SubsystemVendorId);
+
+ /* Clear the statistics block. */
+ for(j = 0x0300; j < 0x0b00; j++)
+ {
+ MEM_WR_OFFSET(pDevice, j, 0);
+ }
+
+ /* Initialize the statistis Block */
+ pDevice->pStatusBlkVirt->Status = 0;
+ pDevice->pStatusBlkVirt->RcvStdConIdx = 0;
+ pDevice->pStatusBlkVirt->RcvJumboConIdx = 0;
+ pDevice->pStatusBlkVirt->RcvMiniConIdx = 0;
+
+ for(j = 0; j < 16; j++)
+ {
+ pDevice->pStatusBlkVirt->Idx[j].RcvProdIdx = 0;
+ pDevice->pStatusBlkVirt->Idx[j].SendConIdx = 0;
+ }
+
+ for(k = 0; k < T3_STD_RCV_RCB_ENTRY_COUNT ;k++)
+ {
+ pDevice->pRxStdBdVirt[k].HostAddr.High = 0;
+ pDevice->pRxStdBdVirt[k].HostAddr.Low = 0;
+ }
+
+#if T3_JUMBO_RCV_RCB_ENTRY_COUNT
+ /* Receive jumbo BD buffer. */
+ for(k = 0; k < T3_JUMBO_RCV_RCB_ENTRY_COUNT; k++)
+ {
+ pDevice->pRxJumboBdVirt[k].HostAddr.High = 0;
+ pDevice->pRxJumboBdVirt[k].HostAddr.Low = 0;
+ }
+#endif
+
+ REG_WR(pDevice, PciCfg.DmaReadWriteCtrl, pDevice->DmaReadWriteCtrl);
+
+ /* GRC mode control register. */
+#ifdef BIG_ENDIAN_PCI /* Jimmy, this ifdef block deleted in new code! */
+ Value32 =
+ GRC_MODE_WORD_SWAP_DATA |
+ GRC_MODE_WORD_SWAP_NON_FRAME_DATA |
+ GRC_MODE_INT_ON_MAC_ATTN |
+ GRC_MODE_HOST_STACK_UP;
+#else
+ /* No CPU Swap modes for PCI IO */
+ Value32 =
+#ifdef BIG_ENDIAN_HOST
+ GRC_MODE_BYTE_SWAP_NON_FRAME_DATA |
+ GRC_MODE_WORD_SWAP_NON_FRAME_DATA |
+ GRC_MODE_BYTE_SWAP_DATA |
+ GRC_MODE_WORD_SWAP_DATA |
+#else
+ GRC_MODE_WORD_SWAP_NON_FRAME_DATA |
+ GRC_MODE_BYTE_SWAP_DATA |
+ GRC_MODE_WORD_SWAP_DATA |
+#endif
+ GRC_MODE_INT_ON_MAC_ATTN |
+ GRC_MODE_HOST_STACK_UP;
+#endif /* !BIG_ENDIAN_PCI */
+
+ /* Configure send BD mode. */
+ if(pDevice->NicSendBd == FALSE)
+ {
+ Value32 |= GRC_MODE_HOST_SEND_BDS;
+ }
+ else
+ {
+ Value32 |= GRC_MODE_4X_NIC_BASED_SEND_RINGS;
+ }
+
+ /* Configure pseudo checksum mode. */
+ if(pDevice->NoTxPseudoHdrChksum)
+ {
+ Value32 |= GRC_MODE_TX_NO_PSEUDO_HEADER_CHKSUM;
+ }
+
+ if(pDevice->NoRxPseudoHdrChksum)
+ {
+ Value32 |= GRC_MODE_RX_NO_PSEUDO_HEADER_CHKSUM;
+ }
+
+ REG_WR(pDevice, Grc.Mode, Value32);
+
+ /* Setup the timer prescalar register. */
+ REG_WR(pDevice, Grc.MiscCfg, 65 << 1); /* Clock is alwasy 66Mhz. */
+
+ /* Set up the MBUF pool base address and size. */
+ REG_WR(pDevice, BufMgr.MbufPoolAddr, pDevice->MbufBase);
+ REG_WR(pDevice, BufMgr.MbufPoolSize, pDevice->MbufSize);
+
+ /* Set up the DMA descriptor pool base address and size. */
+ REG_WR(pDevice, BufMgr.DmaDescPoolAddr, T3_NIC_DMA_DESC_POOL_ADDR);
+ REG_WR(pDevice, BufMgr.DmaDescPoolSize, T3_NIC_DMA_DESC_POOL_SIZE);
+
+ /* Configure MBUF and Threshold watermarks */
+ /* Configure the DMA read MBUF low water mark. */
+ if(pDevice->DmaMbufLowMark)
+ {
+ REG_WR(pDevice, BufMgr.MbufReadDmaLowWaterMark,
+ pDevice->DmaMbufLowMark);
+ }
+ else
+ {
+ if(pDevice->TxMtu < MAX_ETHERNET_PACKET_BUFFER_SIZE)
+ {
+ REG_WR(pDevice, BufMgr.MbufReadDmaLowWaterMark,
+ T3_DEF_DMA_MBUF_LOW_WMARK);
+ }
+ else
+ {
+ REG_WR(pDevice, BufMgr.MbufReadDmaLowWaterMark,
+ T3_DEF_DMA_MBUF_LOW_WMARK_JUMBO);
+ }
+ }
+
+ /* Configure the MAC Rx MBUF low water mark. */
+ if(pDevice->RxMacMbufLowMark)
+ {
+ REG_WR(pDevice, BufMgr.MbufMacRxLowWaterMark,
+ pDevice->RxMacMbufLowMark);
+ }
+ else
+ {
+ if(pDevice->TxMtu < MAX_ETHERNET_PACKET_BUFFER_SIZE)
+ {
+ REG_WR(pDevice, BufMgr.MbufMacRxLowWaterMark,
+ T3_DEF_RX_MAC_MBUF_LOW_WMARK);
+ }
+ else
+ {
+ REG_WR(pDevice, BufMgr.MbufMacRxLowWaterMark,
+ T3_DEF_RX_MAC_MBUF_LOW_WMARK_JUMBO);
+ }
+ }
+
+ /* Configure the MBUF high water mark. */
+ if(pDevice->MbufHighMark)
+ {
+ REG_WR(pDevice, BufMgr.MbufHighWaterMark, pDevice->MbufHighMark);
+ }
+ else
+ {
+ if(pDevice->TxMtu < MAX_ETHERNET_PACKET_BUFFER_SIZE)
+ {
+ REG_WR(pDevice, BufMgr.MbufHighWaterMark,
+ T3_DEF_MBUF_HIGH_WMARK);
+ }
+ else
+ {
+ REG_WR(pDevice, BufMgr.MbufHighWaterMark,
+ T3_DEF_MBUF_HIGH_WMARK_JUMBO);
+ }
+ }
+
+ REG_WR(pDevice, BufMgr.DmaLowWaterMark, T3_DEF_DMA_DESC_LOW_WMARK);
+ REG_WR(pDevice, BufMgr.DmaHighWaterMark, T3_DEF_DMA_DESC_HIGH_WMARK);
+
+ /* Enable buffer manager. */
+ REG_WR(pDevice, BufMgr.Mode, BUFMGR_MODE_ENABLE | BUFMGR_MODE_ATTN_ENABLE);
+
+ for(j = 0 ;j < 2000; j++)
+ {
+ if(REG_RD(pDevice, BufMgr.Mode) & BUFMGR_MODE_ENABLE)
+ break;
+ MM_Wait(10);
+ }
+
+ if(j >= 2000)
+ {
+ return LM_STATUS_FAILURE;
+ }
+
+ /* Enable the FTQs. */
+ REG_WR(pDevice, Ftq.Reset, 0xffffffff);
+ REG_WR(pDevice, Ftq.Reset, 0);
+
+ /* Wait until FTQ is ready */
+ for(j = 0; j < 2000; j++)
+ {
+ if(REG_RD(pDevice, Ftq.Reset) == 0)
+ break;
+ MM_Wait(10);
+ }
+
+ if(j >= 2000)
+ {
+ return LM_STATUS_FAILURE;
+ }
+
+ /* Initialize the Standard Receive RCB. */
+ REG_WR(pDevice, RcvDataBdIn.StdRcvRcb.HostRingAddr.High,
+ pDevice->RxStdBdPhy.High);
+ REG_WR(pDevice, RcvDataBdIn.StdRcvRcb.HostRingAddr.Low,
+ pDevice->RxStdBdPhy.Low);
+ REG_WR(pDevice, RcvDataBdIn.StdRcvRcb.u.MaxLen_Flags,
+ MAX_STD_RCV_BUFFER_SIZE << 16);
+
+ /* Initialize the Jumbo Receive RCB. */
+ REG_WR(pDevice, RcvDataBdIn.JumboRcvRcb.u.MaxLen_Flags,
+ T3_RCB_FLAG_RING_DISABLED);
+#if T3_JUMBO_RCV_RCB_ENTRY_COUNT
+ REG_WR(pDevice, RcvDataBdIn.JumboRcvRcb.HostRingAddr.High,
+ pDevice->RxJumboBdPhy.High);
+ REG_WR(pDevice, RcvDataBdIn.JumboRcvRcb.HostRingAddr.Low,
+ pDevice->RxJumboBdPhy.Low);
+
+ REG_WR(pDevice, RcvDataBdIn.JumboRcvRcb.u.MaxLen_Flags, 0);
+
+#endif /* T3_JUMBO_RCV_RCB_ENTRY_COUNT */
+
+ /* Initialize the Mini Receive RCB. */
+ REG_WR(pDevice, RcvDataBdIn.MiniRcvRcb.u.MaxLen_Flags,
+ T3_RCB_FLAG_RING_DISABLED);
+
+ {
+ REG_WR(pDevice, RcvDataBdIn.StdRcvRcb.NicRingAddr,
+ (LM_UINT32) T3_NIC_STD_RCV_BUFFER_DESC_ADDR);
+ REG_WR(pDevice, RcvDataBdIn.JumboRcvRcb.NicRingAddr,
+ (LM_UINT32) T3_NIC_JUMBO_RCV_BUFFER_DESC_ADDR);
+ }
+
+ /* Receive BD Ring replenish threshold. */
+ REG_WR(pDevice, RcvBdIn.StdRcvThreshold, pDevice->RxStdDescCnt/8);
+#if T3_JUMBO_RCV_RCB_ENTRY_COUNT
+ REG_WR(pDevice, RcvBdIn.JumboRcvThreshold, pDevice->RxJumboDescCnt/8);
+#endif /* T3_JUMBO_RCV_RCB_ENTRY_COUNT */
+
+ /* Disable all the unused rings. */
+ for(j = 0; j < T3_MAX_SEND_RCB_COUNT; j++) {
+ MEM_WR(pDevice, SendRcb[j].u.MaxLen_Flags, T3_RCB_FLAG_RING_DISABLED);
+ } /* for */
+
+ /* Initialize the indices. */
+ pDevice->SendProdIdx = 0;
+ pDevice->SendConIdx = 0;
+
+ MB_REG_WR(pDevice, Mailbox.SendHostProdIdx[0].Low, 0);
+ MB_REG_WR(pDevice, Mailbox.SendNicProdIdx[0].Low, 0);
+
+ /* Set up host or NIC based send RCB. */
+ if(pDevice->NicSendBd == FALSE)
+ {
+ MEM_WR(pDevice, SendRcb[0].HostRingAddr.High,
+ pDevice->SendBdPhy.High);
+ MEM_WR(pDevice, SendRcb[0].HostRingAddr.Low,
+ pDevice->SendBdPhy.Low);
+
+ /* Set up the NIC ring address in the RCB. */
+ MEM_WR(pDevice, SendRcb[0].NicRingAddr,T3_NIC_SND_BUFFER_DESC_ADDR);
+
+ /* Setup the RCB. */
+ MEM_WR(pDevice, SendRcb[0].u.MaxLen_Flags,
+ T3_SEND_RCB_ENTRY_COUNT << 16);
+
+ for(k = 0; k < T3_SEND_RCB_ENTRY_COUNT; k++)
+ {
+ pDevice->pSendBdVirt[k].HostAddr.High = 0;
+ pDevice->pSendBdVirt[k].HostAddr.Low = 0;
+ }
+ }
+ else
+ {
+ MEM_WR(pDevice, SendRcb[0].HostRingAddr.High, 0);
+ MEM_WR(pDevice, SendRcb[0].HostRingAddr.Low, 0);
+ MEM_WR(pDevice, SendRcb[0].NicRingAddr,
+ pDevice->SendBdPhy.Low);
+
+ for(k = 0; k < T3_SEND_RCB_ENTRY_COUNT; k++)
+ {
+ __raw_writel(0, &(pDevice->pSendBdVirt[k].HostAddr.High));
+ __raw_writel(0, &(pDevice->pSendBdVirt[k].HostAddr.Low));
+ __raw_writel(0, &(pDevice->pSendBdVirt[k].u1.Len_Flags));
+ pDevice->ShadowSendBd[k].HostAddr.High = 0;
+ pDevice->ShadowSendBd[k].u1.Len_Flags = 0;
+ }
+ }
+ atomic_set(&pDevice->SendBdLeft, T3_SEND_RCB_ENTRY_COUNT-1);
+
+ /* Configure the receive return rings. */
+ for(j = 0; j < T3_MAX_RCV_RETURN_RCB_COUNT; j++)
+ {
+ MEM_WR(pDevice, RcvRetRcb[j].u.MaxLen_Flags, T3_RCB_FLAG_RING_DISABLED);
+ }
+
+ pDevice->RcvRetConIdx = 0;
+
+ MEM_WR(pDevice, RcvRetRcb[0].HostRingAddr.High,
+ pDevice->RcvRetBdPhy.High);
+ MEM_WR(pDevice, RcvRetRcb[0].HostRingAddr.Low,
+ pDevice->RcvRetBdPhy.Low);
+
+ /* Set up the NIC ring address in the RCB. */
+ /* Not very clear from the spec. I am guessing that for Receive */
+ /* Return Ring, NicRingAddr is not used. */
+ MEM_WR(pDevice, RcvRetRcb[0].NicRingAddr, 0);
+
+ /* Setup the RCB. */
+ MEM_WR(pDevice, RcvRetRcb[0].u.MaxLen_Flags,
+ T3_RCV_RETURN_RCB_ENTRY_COUNT << 16);
+
+ /* Reinitialize RX ring producer index */
+ MB_REG_WR(pDevice, Mailbox.RcvStdProdIdx.Low, 0);
+ MB_REG_WR(pDevice, Mailbox.RcvJumboProdIdx.Low, 0);
+ MB_REG_WR(pDevice, Mailbox.RcvMiniProdIdx.Low, 0);
+
+#if T3_JUMBO_RCV_RCB_ENTRY_COUNT
+ pDevice->RxJumboProdIdx = 0;
+ pDevice->RxJumboQueuedCnt = 0;
+#endif
+
+ /* Reinitialize our copy of the indices. */
+ pDevice->RxStdProdIdx = 0;
+ pDevice->RxStdQueuedCnt = 0;
+
+#if T3_JUMBO_RCV_ENTRY_COUNT
+ pDevice->RxJumboProdIdx = 0;
+#endif /* T3_JUMBO_RCV_ENTRY_COUNT */
+
+ /* Configure the MAC address. */
+ LM_SetMacAddress(pDevice, pDevice->NodeAddress);
+
+ /* Initialize the transmit random backoff seed. */
+ Value32 = (pDevice->NodeAddress[0] + pDevice->NodeAddress[1] +
+ pDevice->NodeAddress[2] + pDevice->NodeAddress[3] +
+ pDevice->NodeAddress[4] + pDevice->NodeAddress[5]) &
+ MAC_TX_BACKOFF_SEED_MASK;
+ REG_WR(pDevice, MacCtrl.TxBackoffSeed, Value32);
+
+ /* Receive MTU. Frames larger than the MTU is marked as oversized. */
+ REG_WR(pDevice, MacCtrl.MtuSize, pDevice->RxMtu + 8); /* CRC + VLAN. */
+
+ /* Configure Time slot/IPG per 802.3 */
+ REG_WR(pDevice, MacCtrl.TxLengths, 0x2620);
+
+ /*
+ * Configure Receive Rules so that packets don't match
+ * Programmble rule will be queued to Return Ring 1
+ */
+ REG_WR(pDevice, MacCtrl.RcvRuleCfg, RX_RULE_DEFAULT_CLASS);
+
+ /*
+ * Configure to have 16 Classes of Services (COS) and one
+ * queue per class. Bad frames are queued to RRR#1.
+ * And frames don't match rules are also queued to COS#1.
+ */
+ REG_WR(pDevice, RcvListPlmt.Config, 0x181);
+
+ /* Enable Receive Placement Statistics */
+ REG_WR(pDevice, RcvListPlmt.StatsEnableMask,0xffffff);
+ REG_WR(pDevice, RcvListPlmt.StatsCtrl, RCV_LIST_STATS_ENABLE);
+
+ /* Enable Send Data Initator Statistics */
+ REG_WR(pDevice, SndDataIn.StatsEnableMask,0xffffff);
+ REG_WR(pDevice, SndDataIn.StatsCtrl,
+ T3_SND_DATA_IN_STATS_CTRL_ENABLE | \
+ T3_SND_DATA_IN_STATS_CTRL_FASTER_UPDATE);
+
+ /* Disable the host coalescing state machine before configuring it's */
+ /* parameters. */
+ REG_WR(pDevice, HostCoalesce.Mode, 0);
+ for(j = 0; j < 2000; j++)
+ {
+ Value32 = REG_RD(pDevice, HostCoalesce.Mode);
+ if(!(Value32 & HOST_COALESCE_ENABLE))
+ {
+ break;
+ }
+ MM_Wait(10);
+ }
+
+ /* Host coalescing configurations. */
+ REG_WR(pDevice, HostCoalesce.RxCoalescingTicks, pDevice->RxCoalescingTicks);
+ REG_WR(pDevice, HostCoalesce.TxCoalescingTicks, pDevice->TxCoalescingTicks);
+ REG_WR(pDevice, HostCoalesce.RxMaxCoalescedFrames,
+ pDevice->RxMaxCoalescedFrames);
+ REG_WR(pDevice, HostCoalesce.TxMaxCoalescedFrames,
+ pDevice->TxMaxCoalescedFrames);
+ REG_WR(pDevice, HostCoalesce.RxCoalescedTickDuringInt,
+ pDevice->RxCoalescingTicksDuringInt);
+ REG_WR(pDevice, HostCoalesce.TxCoalescedTickDuringInt,
+ pDevice->TxCoalescingTicksDuringInt);
+ REG_WR(pDevice, HostCoalesce.RxMaxCoalescedFramesDuringInt,
+ pDevice->RxMaxCoalescedFramesDuringInt);
+ REG_WR(pDevice, HostCoalesce.TxMaxCoalescedFramesDuringInt,
+ pDevice->TxMaxCoalescedFramesDuringInt);
+
+ /* Initialize the address of the status block. The NIC will DMA */
+ /* the status block to this memory which resides on the host. */
+ REG_WR(pDevice, HostCoalesce.StatusBlkHostAddr.High,
+ pDevice->StatusBlkPhy.High);
+ REG_WR(pDevice, HostCoalesce.StatusBlkHostAddr.Low,
+ pDevice->StatusBlkPhy.Low);
+
+ /* Initialize the address of the statistics block. The NIC will DMA */
+ /* the statistics to this block of memory. */
+ REG_WR(pDevice, HostCoalesce.StatsBlkHostAddr.High,
+ pDevice->StatsBlkPhy.High);
+ REG_WR(pDevice, HostCoalesce.StatsBlkHostAddr.Low,
+ pDevice->StatsBlkPhy.Low);
+
+ REG_WR(pDevice, HostCoalesce.StatsCoalescingTicks,
+ pDevice->StatsCoalescingTicks);
+
+ REG_WR(pDevice, HostCoalesce.StatsBlkNicAddr, 0x300);
+ REG_WR(pDevice, HostCoalesce.StatusBlkNicAddr,0xb00);
+
+ /* Enable Host Coalesing state machine */
+ REG_WR(pDevice, HostCoalesce.Mode, HOST_COALESCE_ENABLE |
+ pDevice->CoalesceMode);
+
+ /* Enable the Receive BD Completion state machine. */
+ REG_WR(pDevice, RcvBdComp.Mode, RCV_BD_COMP_MODE_ENABLE |
+ RCV_BD_COMP_MODE_ATTN_ENABLE);
+
+ /* Enable the Receive List Placement state machine. */
+ REG_WR(pDevice, RcvListPlmt.Mode, RCV_LIST_PLMT_MODE_ENABLE);
+
+ /* Enable the Receive List Selector state machine. */
+ REG_WR(pDevice, RcvListSel.Mode, RCV_LIST_SEL_MODE_ENABLE |
+ RCV_LIST_SEL_MODE_ATTN_ENABLE);
+
+ /* Enable transmit DMA, clear statistics. */
+ pDevice->MacMode = MAC_MODE_ENABLE_TX_STATISTICS |
+ MAC_MODE_ENABLE_RX_STATISTICS | MAC_MODE_ENABLE_TDE |
+ MAC_MODE_ENABLE_RDE | MAC_MODE_ENABLE_FHDE;
+ REG_WR(pDevice, MacCtrl.Mode, pDevice->MacMode |
+ MAC_MODE_CLEAR_RX_STATISTICS | MAC_MODE_CLEAR_TX_STATISTICS);
+
+ /* GRC miscellaneous local control register. */
+ pDevice->GrcLocalCtrl = GRC_MISC_LOCAL_CTRL_INT_ON_ATTN |
+ GRC_MISC_LOCAL_CTRL_AUTO_SEEPROM;
+
+ if(T3_ASIC_REV(pDevice->ChipRevId) == T3_ASIC_REV_5700)
+ {
+ pDevice->GrcLocalCtrl |= GRC_MISC_LOCAL_CTRL_GPIO_OE1 |
+ GRC_MISC_LOCAL_CTRL_GPIO_OUTPUT1;
+ }
+
+ REG_WR(pDevice, Grc.LocalCtrl, pDevice->GrcLocalCtrl);
+ MM_Wait(40);
+
+ /* Reset RX counters. */
+ for(j = 0; j < sizeof(LM_RX_COUNTERS); j++)
+ {
+ ((PLM_UINT8) &pDevice->RxCounters)[j] = 0;
+ }
+
+ /* Reset TX counters. */
+ for(j = 0; j < sizeof(LM_TX_COUNTERS); j++)
+ {
+ ((PLM_UINT8) &pDevice->TxCounters)[j] = 0;
+ }
+
+ MB_REG_WR(pDevice, Mailbox.Interrupt[0].Low, 0);
+
+ /* Enable the DMA Completion state machine. */
+ REG_WR(pDevice, DmaComp.Mode, DMA_COMP_MODE_ENABLE);
+
+ /* Enable the DMA Write state machine. */
+ Value32 = DMA_WRITE_MODE_ENABLE |
+ DMA_WRITE_MODE_TARGET_ABORT_ATTN_ENABLE |
+ DMA_WRITE_MODE_MASTER_ABORT_ATTN_ENABLE |
+ DMA_WRITE_MODE_PARITY_ERROR_ATTN_ENABLE |
+ DMA_WRITE_MODE_ADDR_OVERFLOW_ATTN_ENABLE |
+ DMA_WRITE_MODE_FIFO_OVERRUN_ATTN_ENABLE |
+ DMA_WRITE_MODE_FIFO_UNDERRUN_ATTN_ENABLE |
+ DMA_WRITE_MODE_FIFO_OVERREAD_ATTN_ENABLE |
+ DMA_WRITE_MODE_LONG_READ_ATTN_ENABLE;
+ REG_WR(pDevice, DmaWrite.Mode, Value32);
+
+ if (!(pDevice->PciState & T3_PCI_STATE_CONVENTIONAL_PCI_MODE))
+ {
+ if (pDevice->ChipRevId == T3_CHIP_ID_5704_A0)
+ {
+ Value16 = REG_RD(pDevice, PciCfg.PciXCommand);
+ Value16 &= ~(PCIX_CMD_MAX_SPLIT_MASK | PCIX_CMD_MAX_BURST_MASK);
+ Value16 |= ((PCIX_CMD_MAX_BURST_CPIOB << PCIX_CMD_MAX_BURST_SHL) &
+ PCIX_CMD_MAX_BURST_MASK);
+ if (pDevice->SplitModeEnable == SPLIT_MODE_ENABLE)
+ {
+ Value16 |= (pDevice->SplitModeMaxReq << PCIX_CMD_MAX_SPLIT_SHL)
+ & PCIX_CMD_MAX_SPLIT_MASK;
+ }
+ REG_WR(pDevice, PciCfg.PciXCommand, Value16);
+ }
+ }
+
+ /* Enable the Read DMA state machine. */
+ Value32 = DMA_READ_MODE_ENABLE |
+ DMA_READ_MODE_TARGET_ABORT_ATTN_ENABLE |
+ DMA_READ_MODE_MASTER_ABORT_ATTN_ENABLE |
+ DMA_READ_MODE_PARITY_ERROR_ATTN_ENABLE |
+ DMA_READ_MODE_ADDR_OVERFLOW_ATTN_ENABLE |
+ DMA_READ_MODE_FIFO_OVERRUN_ATTN_ENABLE |
+ DMA_READ_MODE_FIFO_UNDERRUN_ATTN_ENABLE |
+ DMA_READ_MODE_FIFO_OVERREAD_ATTN_ENABLE |
+ DMA_READ_MODE_LONG_READ_ATTN_ENABLE;
+
+ if (pDevice->SplitModeEnable == SPLIT_MODE_ENABLE)
+ {
+ Value32 |= DMA_READ_MODE_SPLIT_ENABLE;
+ }
+ REG_WR(pDevice, DmaRead.Mode, Value32);
+
+ /* Enable the Receive Data Completion state machine. */
+ REG_WR(pDevice, RcvDataComp.Mode, RCV_DATA_COMP_MODE_ENABLE |
+ RCV_DATA_COMP_MODE_ATTN_ENABLE);
+
+ /* Enable the Mbuf Cluster Free state machine. */
+ REG_WR(pDevice, MbufClusterFree.Mode, MBUF_CLUSTER_FREE_MODE_ENABLE);
+
+ /* Enable the Send Data Completion state machine. */
+ REG_WR(pDevice, SndDataComp.Mode, SND_DATA_COMP_MODE_ENABLE);
+
+ /* Enable the Send BD Completion state machine. */
+ REG_WR(pDevice, SndBdComp.Mode, SND_BD_COMP_MODE_ENABLE |
+ SND_BD_COMP_MODE_ATTN_ENABLE);
+
+ /* Enable the Receive BD Initiator state machine. */
+ REG_WR(pDevice, RcvBdIn.Mode, RCV_BD_IN_MODE_ENABLE |
+ RCV_BD_IN_MODE_BD_IN_DIABLED_RCB_ATTN_ENABLE);
+
+ /* Enable the Receive Data and Receive BD Initiator state machine. */
+ REG_WR(pDevice, RcvDataBdIn.Mode, RCV_DATA_BD_IN_MODE_ENABLE |
+ RCV_DATA_BD_IN_MODE_INVALID_RING_SIZE);
+
+ /* Enable the Send Data Initiator state machine. */
+ REG_WR(pDevice, SndDataIn.Mode, T3_SND_DATA_IN_MODE_ENABLE);
+
+ /* Enable the Send BD Initiator state machine. */
+ REG_WR(pDevice, SndBdIn.Mode, SND_BD_IN_MODE_ENABLE |
+ SND_BD_IN_MODE_ATTN_ENABLE);
+
+ /* Enable the Send BD Selector state machine. */
+ REG_WR(pDevice, SndBdSel.Mode, SND_BD_SEL_MODE_ENABLE |
+ SND_BD_SEL_MODE_ATTN_ENABLE);
+
+#if INCLUDE_5701_AX_FIX
+ /* Load the firmware for the 5701_A0 workaround. */
+ if(pDevice->ChipRevId == T3_CHIP_ID_5701_A0)
+ {
+ LM_LoadRlsFirmware(pDevice);
+ }
+#endif
+
+ /* Enable the transmitter. */
+ pDevice->TxMode = TX_MODE_ENABLE;
+ REG_WR(pDevice, MacCtrl.TxMode, pDevice->TxMode);
+
+ /* Enable the receiver. */
+ pDevice->RxMode = RX_MODE_ENABLE;
+ REG_WR(pDevice, MacCtrl.RxMode, pDevice->RxMode);
+
+ if (pDevice->RestoreOnWakeUp)
+ {
+ pDevice->RestoreOnWakeUp = FALSE;
+ pDevice->DisableAutoNeg = pDevice->WakeUpDisableAutoNeg;
+ pDevice->RequestedMediaType = pDevice->WakeUpRequestedMediaType;
+ }
+
+ /* Disable auto polling. */
+ pDevice->MiMode = 0xc0000;
+ REG_WR(pDevice, MacCtrl.MiMode, pDevice->MiMode);
+
+ if(T3_ASIC_REV(pDevice->ChipRevId) == T3_ASIC_REV_5700 ||
+ T3_ASIC_REV(pDevice->ChipRevId) == T3_ASIC_REV_5701)
+ {
+ Value32 = LED_CTRL_PHY_MODE_1;
+ }
+ else
+ {
+ if(pDevice->LedMode == LED_MODE_OUTPUT)
+ {
+ Value32 = LED_CTRL_PHY_MODE_2;
+ }
+ else
+ {
+ Value32 = LED_CTRL_PHY_MODE_1;
+ }
+ }
+ REG_WR(pDevice, MacCtrl.LedCtrl, Value32);
+
+ /* Activate Link to enable MAC state machine */
+ REG_WR(pDevice, MacCtrl.MiStatus, MI_STATUS_ENABLE_LINK_STATUS_ATTN);
+
+ if (pDevice->EnableTbi)
+ {
+ REG_WR(pDevice, MacCtrl.RxMode, RX_MODE_RESET);
+ MM_Wait(10);
+ REG_WR(pDevice, MacCtrl.RxMode, pDevice->RxMode);
+ if (pDevice->ChipRevId == T3_CHIP_ID_5703_A1)
+ {
+ REG_WR(pDevice, MacCtrl.SerdesCfg, 0x616000);
+ }
+ }
+ /* Setup the phy chip. */
+ LM_SetupPhy(pDevice);
+
+ if (!pDevice->EnableTbi) {
+ /* Clear CRC stats */
+ LM_ReadPhy(pDevice, 0x1e, &Value32);
+ LM_WritePhy(pDevice, 0x1e, Value32 | 0x8000);
+ LM_ReadPhy(pDevice, 0x14, &Value32);
+ }
+
+ /* Set up the receive mask. */
+ LM_SetReceiveMask(pDevice, pDevice->ReceiveMask);
+
+ /* Queue Rx packet buffers. */
+ if(pDevice->QueueRxPackets)
+ {
+ LM_QueueRxPackets(pDevice);
+ }
+
+ /* Enable interrupt to the host. */
+ if(pDevice->InitDone)
+ {
+ LM_EnableInterrupt(pDevice);
+ }
+
+ return LM_STATUS_SUCCESS;
+} /* LM_ResetAdapter */
+
+
+/******************************************************************************/
+/* Description: */
+/* This routine disables the adapter from generating interrupts. */
+/* */
+/* Return: */
+/* LM_STATUS_SUCCESS */
+/******************************************************************************/
+LM_STATUS
+LM_DisableInterrupt(
+ PLM_DEVICE_BLOCK pDevice)
+{
+ REG_WR(pDevice, PciCfg.MiscHostCtrl, pDevice->MiscHostCtrl |
+ MISC_HOST_CTRL_MASK_PCI_INT);
+ MB_REG_WR(pDevice, Mailbox.Interrupt[0].Low, 1);
+
+ return LM_STATUS_SUCCESS;
+}
+
+
+
+/******************************************************************************/
+/* Description: */
+/* This routine enables the adapter to generate interrupts. */
+/* */
+/* Return: */
+/* LM_STATUS_SUCCESS */
+/******************************************************************************/
+LM_STATUS
+LM_EnableInterrupt(
+ PLM_DEVICE_BLOCK pDevice)
+{
+ REG_WR(pDevice, PciCfg.MiscHostCtrl, pDevice->MiscHostCtrl &
+ ~MISC_HOST_CTRL_MASK_PCI_INT);
+ MB_REG_WR(pDevice, Mailbox.Interrupt[0].Low, 0);
+
+ if(pDevice->pStatusBlkVirt->Status & STATUS_BLOCK_UPDATED)
+ {
+ REG_WR(pDevice, Grc.LocalCtrl, pDevice->GrcLocalCtrl |
+ GRC_MISC_LOCAL_CTRL_SET_INT);
+ }
+
+ return LM_STATUS_SUCCESS;
+}
+
+
+
+/******************************************************************************/
+/* Description: */
+/* This routine puts a packet on the wire if there is a transmit DMA */
+/* descriptor available; otherwise the packet is queued for later */
+/* transmission. If the second argue is NULL, this routine will put */
+/* the queued packet on the wire if possible. */
+/* */
+/* Return: */
+/* LM_STATUS_SUCCESS */
+/******************************************************************************/
+#if 0
+LM_STATUS
+LM_SendPacket(PLM_DEVICE_BLOCK pDevice, PLM_PACKET pPacket)
+{
+ LM_UINT32 FragCount;
+ PT3_SND_BD pSendBd;
+ PT3_SND_BD pShadowSendBd;
+ LM_UINT32 Value32, Len;
+ LM_UINT32 Idx;
+
+ if (T3_ASIC_REV(pDevice->ChipRevId) == T3_ASIC_REV_5700) {
+ return LM_5700SendPacket(pDevice, pPacket);
+ }
+
+ /* Update the SendBdLeft count. */
+ atomic_sub(pPacket->u.Tx.FragCount, &pDevice->SendBdLeft);
+
+ /* Initalize the send buffer descriptors. */
+ Idx = pDevice->SendProdIdx;
+
+ pSendBd = &pDevice->pSendBdVirt[Idx];
+
+ /* Next producer index. */
+ if (pDevice->NicSendBd == TRUE)
+ {
+ T3_64BIT_HOST_ADDR paddr;
+
+ pShadowSendBd = &pDevice->ShadowSendBd[Idx];
+ for(FragCount = 0; ; )
+ {
+ MM_MapTxDma(pDevice, pPacket, &paddr, &Len, FragCount);
+ /* Initialize the pointer to the send buffer fragment. */
+ if (paddr.High != pShadowSendBd->HostAddr.High)
+ {
+ __raw_writel(paddr.High, &(pSendBd->HostAddr.High));
+ pShadowSendBd->HostAddr.High = paddr.High;
+ }
+ __raw_writel(paddr.Low, &(pSendBd->HostAddr.Low));
+
+ /* Setup the control flags and send buffer size. */
+ Value32 = (Len << 16) | pPacket->Flags;
+
+ Idx = (Idx + 1) & T3_SEND_RCB_ENTRY_COUNT_MASK;
+
+ FragCount++;
+ if (FragCount >= pPacket->u.Tx.FragCount)
+ {
+ Value32 |= SND_BD_FLAG_END;
+ if (Value32 != pShadowSendBd->u1.Len_Flags)
+ {
+ __raw_writel(Value32, &(pSendBd->u1.Len_Flags));
+ pShadowSendBd->u1.Len_Flags = Value32;
+ }
+ if (pPacket->Flags & SND_BD_FLAG_VLAN_TAG) {
+ __raw_writel(pPacket->VlanTag, &(pSendBd->u2.VlanTag));
+ }
+ break;
+ }
+ else
+ {
+ if (Value32 != pShadowSendBd->u1.Len_Flags)
+ {
+ __raw_writel(Value32, &(pSendBd->u1.Len_Flags));
+ pShadowSendBd->u1.Len_Flags = Value32;
+ }
+ if (pPacket->Flags & SND_BD_FLAG_VLAN_TAG) {
+ __raw_writel(pPacket->VlanTag, &(pSendBd->u2.VlanTag));
+ }
+ }
+
+ pSendBd++;
+ pShadowSendBd++;
+ if (Idx == 0)
+ {
+ pSendBd = &pDevice->pSendBdVirt[0];
+ pShadowSendBd = &pDevice->ShadowSendBd[0];
+ }
+ } /* for */
+
+ /* Put the packet descriptor in the ActiveQ. */
+ QQ_PushTail(&pDevice->TxPacketActiveQ.Container, pPacket);
+
+ wmb();
+ MB_REG_WR(pDevice, Mailbox.SendNicProdIdx[0].Low, Idx);
+
+ }
+ else
+ {
+ for(FragCount = 0; ; )
+ {
+ /* Initialize the pointer to the send buffer fragment. */
+ MM_MapTxDma(pDevice, pPacket, &pSendBd->HostAddr, &Len, FragCount);
+
+ pSendBd->u2.VlanTag = pPacket->VlanTag;
+
+ /* Setup the control flags and send buffer size. */
+ Value32 = (Len << 16) | pPacket->Flags;
+
+ Idx = (Idx + 1) & T3_SEND_RCB_ENTRY_COUNT_MASK;
+
+ FragCount++;
+ if (FragCount >= pPacket->u.Tx.FragCount)
+ {
+ pSendBd->u1.Len_Flags = Value32 | SND_BD_FLAG_END;
+ break;
+ }
+ else
+ {
+ pSendBd->u1.Len_Flags = Value32;
+ }
+ pSendBd++;
+ if (Idx == 0)
+ {
+ pSendBd = &pDevice->pSendBdVirt[0];
+ }
+ } /* for */
+
+ /* Put the packet descriptor in the ActiveQ. */
+ QQ_PushTail(&pDevice->TxPacketActiveQ.Container, pPacket);
+
+ wmb();
+ MB_REG_WR(pDevice, Mailbox.SendHostProdIdx[0].Low, Idx);
+
+ }
+
+ /* Update the producer index. */
+ pDevice->SendProdIdx = Idx;
+
+ return LM_STATUS_SUCCESS;
+}
+#endif
+
+LM_STATUS
+LM_SendPacket(PLM_DEVICE_BLOCK pDevice, PLM_PACKET pPacket)
+{
+ LM_UINT32 FragCount;
+ PT3_SND_BD pSendBd, pTmpSendBd, pShadowSendBd;
+ T3_SND_BD NicSendBdArr[MAX_FRAGMENT_COUNT];
+ LM_UINT32 StartIdx, Idx;
+
+ while (1)
+ {
+ /* Initalize the send buffer descriptors. */
+ StartIdx = Idx = pDevice->SendProdIdx;
+
+ if (pDevice->NicSendBd)
+ {
+ pTmpSendBd = pSendBd = &NicSendBdArr[0];
+ }
+ else
+ {
+ pTmpSendBd = pSendBd = &pDevice->pSendBdVirt[Idx];
+ }
+
+ /* Next producer index. */
+ for(FragCount = 0; ; )
+ {
+ LM_UINT32 Value32, Len;
+
+ /* Initialize the pointer to the send buffer fragment. */
+ MM_MapTxDma(pDevice, pPacket, &pSendBd->HostAddr, &Len, FragCount);
+
+ pSendBd->u2.VlanTag = pPacket->VlanTag;
+
+ /* Setup the control flags and send buffer size. */
+ Value32 = (Len << 16) | pPacket->Flags;
+
+ Idx = (Idx + 1) & T3_SEND_RCB_ENTRY_COUNT_MASK;
+
+ FragCount++;
+ if (FragCount >= pPacket->u.Tx.FragCount)
+ {
+ pSendBd->u1.Len_Flags = Value32 | SND_BD_FLAG_END;
+ break;
+ }
+ else
+ {
+ pSendBd->u1.Len_Flags = Value32;
+ }
+ pSendBd++;
+ if ((Idx == 0) && !pDevice->NicSendBd)
+ {
+ pSendBd = &pDevice->pSendBdVirt[0];
+ }
+ } /* for */
+ if (T3_ASIC_REV(pDevice->ChipRevId) == T3_ASIC_REV_5700)
+ {
+ if (LM_Test4GBoundary(pDevice, pPacket, pTmpSendBd) ==
+ LM_STATUS_SUCCESS)
+ {
+ if (MM_CoalesceTxBuffer(pDevice, pPacket) != LM_STATUS_SUCCESS)
+ {
+ QQ_PushHead(&pDevice->TxPacketFreeQ.Container, pPacket);
+ return LM_STATUS_FAILURE;
+ }
+ continue;
+ }
+ }
+ break;
+ }
+ /* Put the packet descriptor in the ActiveQ. */
+ QQ_PushTail(&pDevice->TxPacketActiveQ.Container, pPacket);
+
+ if (pDevice->NicSendBd)
+ {
+ pSendBd = &pDevice->pSendBdVirt[StartIdx];
+ pShadowSendBd = &pDevice->ShadowSendBd[StartIdx];
+
+ while (StartIdx != Idx)
+ {
+ LM_UINT32 Value32;
+
+ if ((Value32 = pTmpSendBd->HostAddr.High) !=
+ pShadowSendBd->HostAddr.High)
+ {
+ __raw_writel(Value32, &(pSendBd->HostAddr.High));
+ pShadowSendBd->HostAddr.High = Value32;
+ }
+
+ __raw_writel(pTmpSendBd->HostAddr.Low, &(pSendBd->HostAddr.Low));
+
+ if ((Value32 = pTmpSendBd->u1.Len_Flags) !=
+ pShadowSendBd->u1.Len_Flags)
+ {
+ __raw_writel(Value32, &(pSendBd->u1.Len_Flags));
+ pShadowSendBd->u1.Len_Flags = Value32;
+ }
+
+ if (pPacket->Flags & SND_BD_FLAG_VLAN_TAG)
+ {
+ __raw_writel(pTmpSendBd->u2.VlanTag, &(pSendBd->u2.VlanTag));
+ }
+
+ StartIdx = (StartIdx + 1) & T3_SEND_RCB_ENTRY_COUNT_MASK;
+ if (StartIdx == 0)
+ pSendBd = &pDevice->pSendBdVirt[0];
+ else
+ pSendBd++;
+ pTmpSendBd++;
+ }
+ wmb();
+ MB_REG_WR(pDevice, Mailbox.SendNicProdIdx[0].Low, Idx);
+
+ if(T3_CHIP_REV(pDevice->ChipRevId) == T3_CHIP_REV_5700_BX)
+ {
+ MB_REG_WR(pDevice, Mailbox.SendNicProdIdx[0].Low, Idx);
+ }
+ }
+ else
+ {
+ wmb();
+ MB_REG_WR(pDevice, Mailbox.SendHostProdIdx[0].Low, Idx);
+
+ if(T3_CHIP_REV(pDevice->ChipRevId) == T3_CHIP_REV_5700_BX)
+ {
+ MB_REG_WR(pDevice, Mailbox.SendHostProdIdx[0].Low, Idx);
+ }
+ }
+
+ /* Update the SendBdLeft count. */
+ atomic_sub(pPacket->u.Tx.FragCount, &pDevice->SendBdLeft);
+
+ /* Update the producer index. */
+ pDevice->SendProdIdx = Idx;
+
+ return LM_STATUS_SUCCESS;
+}
+
+STATIC LM_STATUS
+LM_Test4GBoundary(PLM_DEVICE_BLOCK pDevice, PLM_PACKET pPacket,
+ PT3_SND_BD pSendBd)
+{
+ int FragCount;
+ LM_UINT32 Idx, Base, Len;
+
+ Idx = pDevice->SendProdIdx;
+ for(FragCount = 0; ; )
+ {
+ Len = pSendBd->u1.Len_Flags >> 16;
+ if (((Base = pSendBd->HostAddr.Low) > 0xffffdcc0) &&
+ (pSendBd->HostAddr.High == 0) &&
+ ((Base + 8 + Len) < Base))
+ {
+ return LM_STATUS_SUCCESS;
+ }
+ FragCount++;
+ if (FragCount >= pPacket->u.Tx.FragCount)
+ {
+ break;
+ }
+ pSendBd++;
+ if (!pDevice->NicSendBd)
+ {
+ Idx = (Idx + 1) & T3_SEND_RCB_ENTRY_COUNT_MASK;
+ if (Idx == 0)
+ {
+ pSendBd = &pDevice->pSendBdVirt[0];
+ }
+ }
+ }
+ return LM_STATUS_FAILURE;
+}
+
+/******************************************************************************/
+/* Description: */
+/* */
+/* Return: */
+/******************************************************************************/
+__inline static unsigned long
+ComputeCrc32(
+unsigned char *pBuffer,
+unsigned long BufferSize) {
+ unsigned long Reg;
+ unsigned long Tmp;
+ unsigned long j, k;
+
+ Reg = 0xffffffff;
+
+ for(j = 0; j < BufferSize; j++)
+ {
+ Reg ^= pBuffer[j];
+
+ for(k = 0; k < 8; k++)
+ {
+ Tmp = Reg & 0x01;
+
+ Reg >>= 1;
+
+ if(Tmp)
+ {
+ Reg ^= 0xedb88320;
+ }
+ }
+ }
+
+ return ~Reg;
+} /* ComputeCrc32 */
+
+
+
+/******************************************************************************/
+/* Description: */
+/* This routine sets the receive control register according to ReceiveMask */
+/* */
+/* Return: */
+/* LM_STATUS_SUCCESS */
+/******************************************************************************/
+LM_STATUS
+LM_SetReceiveMask(
+PLM_DEVICE_BLOCK pDevice,
+LM_UINT32 Mask) {
+ LM_UINT32 ReceiveMask;
+ LM_UINT32 RxMode;
+ LM_UINT32 j, k;
+
+ ReceiveMask = Mask;
+
+ RxMode = pDevice->RxMode;
+
+ if(Mask & LM_ACCEPT_UNICAST)
+ {
+ Mask &= ~LM_ACCEPT_UNICAST;
+ }
+
+ if(Mask & LM_ACCEPT_MULTICAST)
+ {
+ Mask &= ~LM_ACCEPT_MULTICAST;
+ }
+
+ if(Mask & LM_ACCEPT_ALL_MULTICAST)
+ {
+ Mask &= ~LM_ACCEPT_ALL_MULTICAST;
+ }
+
+ if(Mask & LM_ACCEPT_BROADCAST)
+ {
+ Mask &= ~LM_ACCEPT_BROADCAST;
+ }
+
+ RxMode &= ~RX_MODE_PROMISCUOUS_MODE;
+ if(Mask & LM_PROMISCUOUS_MODE)
+ {
+ RxMode |= RX_MODE_PROMISCUOUS_MODE;
+ Mask &= ~LM_PROMISCUOUS_MODE;
+ }
+
+ RxMode &= ~(RX_MODE_ACCEPT_RUNTS | RX_MODE_ACCEPT_OVERSIZED);
+ if(Mask & LM_ACCEPT_ERROR_PACKET)
+ {
+ RxMode |= RX_MODE_ACCEPT_RUNTS | RX_MODE_ACCEPT_OVERSIZED;
+ Mask &= ~LM_ACCEPT_ERROR_PACKET;
+ }
+
+ /* Make sure all the bits are valid before committing changes. */
+ if(Mask)
+ {
+ return LM_STATUS_FAILURE;
+ }
+
+ /* Commit the new filter. */
+ pDevice->RxMode = RxMode;
+ REG_WR(pDevice, MacCtrl.RxMode, RxMode);
+
+ pDevice->ReceiveMask = ReceiveMask;
+
+ /* Set up the MC hash table. */
+ if(ReceiveMask & LM_ACCEPT_ALL_MULTICAST)
+ {
+ for(k = 0; k < 4; k++)
+ {
+ REG_WR(pDevice, MacCtrl.HashReg[k], 0xffffffff);
+ }
+ }
+ else if(ReceiveMask & LM_ACCEPT_MULTICAST)
+ {
+ LM_UINT32 HashReg[4];
+
+ HashReg[0] = 0; HashReg[1] = 0; HashReg[2] = 0; HashReg[3] = 0;
+ for(j = 0; j < pDevice->McEntryCount; j++)
+ {
+ LM_UINT32 RegIndex;
+ LM_UINT32 Bitpos;
+ LM_UINT32 Crc32;
+
+ Crc32 = ComputeCrc32(pDevice->McTable[j], ETHERNET_ADDRESS_SIZE);
+
+ /* The most significant 7 bits of the CRC32 (no inversion), */
+ /* are used to index into one of the possible 128 bit positions. */
+ Bitpos = ~Crc32 & 0x7f;
+
+ /* Hash register index. */
+ RegIndex = (Bitpos & 0x60) >> 5;
+
+ /* Bit to turn on within a hash register. */
+ Bitpos &= 0x1f;
+
+ /* Enable the multicast bit. */
+ HashReg[RegIndex] |= (1 << Bitpos);
+ }
+
+ /* REV_AX has problem with multicast filtering where it uses both */
+ /* DA and SA to perform hashing. */
+ for(k = 0; k < 4; k++)
+ {
+ REG_WR(pDevice, MacCtrl.HashReg[k], HashReg[k]);
+ }
+ }
+ else
+ {
+ /* Reject all multicast frames. */
+ for(j = 0; j < 4; j++)
+ {
+ REG_WR(pDevice, MacCtrl.HashReg[j], 0);
+ }
+ }
+
+ /* By default, Tigon3 will accept broadcast frames. We need to setup */
+ if(ReceiveMask & LM_ACCEPT_BROADCAST)
+ {
+ REG_WR(pDevice, MacCtrl.RcvRules[RCV_RULE1_REJECT_BROADCAST_IDX].Rule,
+ REJECT_BROADCAST_RULE1_RULE & RCV_DISABLE_RULE_MASK);
+ REG_WR(pDevice, MacCtrl.RcvRules[RCV_RULE1_REJECT_BROADCAST_IDX].Value,
+ REJECT_BROADCAST_RULE1_VALUE & RCV_DISABLE_RULE_MASK);
+ REG_WR(pDevice, MacCtrl.RcvRules[RCV_RULE2_REJECT_BROADCAST_IDX].Rule,
+ REJECT_BROADCAST_RULE1_RULE & RCV_DISABLE_RULE_MASK);
+ REG_WR(pDevice, MacCtrl.RcvRules[RCV_RULE2_REJECT_BROADCAST_IDX].Value,
+ REJECT_BROADCAST_RULE1_VALUE & RCV_DISABLE_RULE_MASK);
+ }
+ else
+ {
+ REG_WR(pDevice, MacCtrl.RcvRules[RCV_RULE1_REJECT_BROADCAST_IDX].Rule,
+ REJECT_BROADCAST_RULE1_RULE);
+ REG_WR(pDevice, MacCtrl.RcvRules[RCV_RULE1_REJECT_BROADCAST_IDX].Value,
+ REJECT_BROADCAST_RULE1_VALUE);
+ REG_WR(pDevice, MacCtrl.RcvRules[RCV_RULE2_REJECT_BROADCAST_IDX].Rule,
+ REJECT_BROADCAST_RULE2_RULE);
+ REG_WR(pDevice, MacCtrl.RcvRules[RCV_RULE2_REJECT_BROADCAST_IDX].Value,
+ REJECT_BROADCAST_RULE2_VALUE);
+ }
+
+ /* disable the rest of the rules. */
+ for(j = RCV_LAST_RULE_IDX; j < 16; j++)
+ {
+ REG_WR(pDevice, MacCtrl.RcvRules[j].Rule, 0);
+ REG_WR(pDevice, MacCtrl.RcvRules[j].Value, 0);
+ }
+
+ return LM_STATUS_SUCCESS;
+} /* LM_SetReceiveMask */
+
+
+
+/******************************************************************************/
+/* Description: */
+/* Disable the interrupt and put the transmitter and receiver engines in */
+/* an idle state. Also aborts all pending send requests and receive */
+/* buffers. */
+/* */
+/* Return: */
+/* LM_STATUS_SUCCESS */
+/******************************************************************************/
+LM_STATUS
+LM_Abort(
+PLM_DEVICE_BLOCK pDevice)
+{
+ PLM_PACKET pPacket;
+ LM_UINT Idx;
+
+ LM_DisableInterrupt(pDevice);
+
+ /* Disable all the state machines. */
+ LM_CntrlBlock(pDevice,T3_BLOCK_MAC_RX_ENGINE,LM_DISABLE);
+ LM_CntrlBlock(pDevice,T3_BLOCK_RX_BD_INITIATOR,LM_DISABLE);
+ LM_CntrlBlock(pDevice,T3_BLOCK_RX_LIST_PLMT,LM_DISABLE);
+ LM_CntrlBlock(pDevice,T3_BLOCK_RX_LIST_SELECTOR,LM_DISABLE);
+ LM_CntrlBlock(pDevice,T3_BLOCK_RX_DATA_INITIATOR,LM_DISABLE);
+ LM_CntrlBlock(pDevice,T3_BLOCK_RX_DATA_COMP,LM_DISABLE);
+ LM_CntrlBlock(pDevice,T3_BLOCK_RX_BD_COMP,LM_DISABLE);
+
+ LM_CntrlBlock(pDevice,T3_BLOCK_SEND_BD_SELECTOR,LM_DISABLE);
+ LM_CntrlBlock(pDevice,T3_BLOCK_SEND_BD_INITIATOR,LM_DISABLE);
+ LM_CntrlBlock(pDevice,T3_BLOCK_SEND_DATA_INITIATOR,LM_DISABLE);
+ LM_CntrlBlock(pDevice,T3_BLOCK_DMA_RD,LM_DISABLE);
+ LM_CntrlBlock(pDevice,T3_BLOCK_SEND_DATA_COMP,LM_DISABLE);
+ LM_CntrlBlock(pDevice,T3_BLOCK_DMA_COMP,LM_DISABLE);
+ LM_CntrlBlock(pDevice,T3_BLOCK_SEND_BD_COMP,LM_DISABLE);
+
+ /* Clear TDE bit */
+ pDevice->MacMode &= ~MAC_MODE_ENABLE_TDE;
+ REG_WR(pDevice, MacCtrl.Mode, pDevice->MacMode);
+
+ LM_CntrlBlock(pDevice,T3_BLOCK_MAC_TX_ENGINE,LM_DISABLE);
+ LM_CntrlBlock(pDevice,T3_BLOCK_HOST_COALESING,LM_DISABLE);
+ LM_CntrlBlock(pDevice,T3_BLOCK_DMA_WR,LM_DISABLE);
+ LM_CntrlBlock(pDevice,T3_BLOCK_MBUF_CLUSTER_FREE,LM_DISABLE);
+
+ /* Reset all FTQs */
+ REG_WR(pDevice, Ftq.Reset, 0xffffffff);
+ REG_WR(pDevice, Ftq.Reset, 0x0);
+
+ LM_CntrlBlock(pDevice,T3_BLOCK_MBUF_MANAGER,LM_DISABLE);
+ LM_CntrlBlock(pDevice,T3_BLOCK_MEM_ARBITOR,LM_DISABLE);
+
+ MM_ACQUIRE_INT_LOCK(pDevice);
+
+ /* Abort packets that have already queued to go out. */
+ pPacket = (PLM_PACKET) QQ_PopHead(&pDevice->TxPacketActiveQ.Container);
+ while(pPacket)
+ {
+
+ pPacket->PacketStatus = LM_STATUS_TRANSMIT_ABORTED;
+ pDevice->TxCounters.TxPacketAbortedCnt++;
+
+ atomic_add(pPacket->u.Tx.FragCount, &pDevice->SendBdLeft);
+
+ QQ_PushTail(&pDevice->TxPacketXmittedQ.Container, pPacket);
+
+ pPacket = (PLM_PACKET)
+ QQ_PopHead(&pDevice->TxPacketActiveQ.Container);
+ }
+
+ /* Cleanup the receive return rings. */
+ LM_ServiceRxInterrupt(pDevice);
+
+ /* Don't want to indicate rx packets in Ndis miniport shutdown context. */
+ /* Doing so may cause system crash. */
+ if(!pDevice->ShuttingDown)
+ {
+ /* Indicate packets to the protocol. */
+ MM_IndicateTxPackets(pDevice);
+
+ /* Indicate received packets to the protocols. */
+ MM_IndicateRxPackets(pDevice);
+ }
+ else
+ {
+ /* Move the receive packet descriptors in the ReceivedQ to the */
+ /* free queue. */
+ for(; ;)
+ {
+ pPacket = (PLM_PACKET) QQ_PopHead(
+ &pDevice->RxPacketReceivedQ.Container);
+ if(pPacket == NULL)
+ {
+ break;
+ }
+ QQ_PushTail(&pDevice->RxPacketFreeQ.Container, pPacket);
+ }
+ }
+
+ /* Clean up the Std Receive Producer ring. */
+ Idx = pDevice->pStatusBlkVirt->RcvStdConIdx;
+
+ while(Idx != pDevice->RxStdProdIdx) {
+ pPacket = (PLM_PACKET) (MM_UINT_PTR(pDevice->pPacketDescBase) +
+ MM_UINT_PTR(pDevice->pRxStdBdVirt[Idx].Opaque));
+
+ QQ_PushTail(&pDevice->RxPacketFreeQ.Container, pPacket);
+
+ Idx = (Idx + 1) & T3_STD_RCV_RCB_ENTRY_COUNT_MASK;
+ } /* while */
+
+ /* Reinitialize our copy of the indices. */
+ pDevice->RxStdProdIdx = 0;
+
+#if T3_JUMBO_RCV_RCB_ENTRY_COUNT
+ /* Clean up the Jumbo Receive Producer ring. */
+ Idx = pDevice->pStatusBlkVirt->RcvJumboConIdx;
+
+ while(Idx != pDevice->RxJumboProdIdx) {
+ pPacket = (PLM_PACKET) (MM_UINT_PTR(pDevice->pPacketDescBase) +
+ MM_UINT_PTR(pDevice->pRxJumboBdVirt[Idx].Opaque));
+
+ QQ_PushTail(&pDevice->RxPacketFreeQ.Container, pPacket);
+
+ Idx = (Idx + 1) & T3_JUMBO_RCV_RCB_ENTRY_COUNT_MASK;
+ } /* while */
+
+ /* Reinitialize our copy of the indices. */
+ pDevice->RxJumboProdIdx = 0;
+#endif /* T3_JUMBO_RCV_RCB_ENTRY_COUNT */
+
+ MM_RELEASE_INT_LOCK(pDevice);
+
+ /* Initialize the statistis Block */
+ pDevice->pStatusBlkVirt->Status = 0;
+ pDevice->pStatusBlkVirt->RcvStdConIdx = 0;
+ pDevice->pStatusBlkVirt->RcvJumboConIdx = 0;
+ pDevice->pStatusBlkVirt->RcvMiniConIdx = 0;
+
+ return LM_STATUS_SUCCESS;
+} /* LM_Abort */
+
+
+
+/******************************************************************************/
+/* Description: */
+/* Disable the interrupt and put the transmitter and receiver engines in */
+/* an idle state. Aborts all pending send requests and receive buffers. */
+/* Also free all the receive buffers. */
+/* */
+/* Return: */
+/* LM_STATUS_SUCCESS */
+/******************************************************************************/
+LM_STATUS
+LM_Halt(
+PLM_DEVICE_BLOCK pDevice) {
+ PLM_PACKET pPacket;
+ LM_UINT32 EntryCnt;
+
+ LM_Abort(pDevice);
+
+ /* Get the number of entries in the queue. */
+ EntryCnt = QQ_GetEntryCnt(&pDevice->RxPacketFreeQ.Container);
+
+ /* Make sure all the packets have been accounted for. */
+ for(EntryCnt = 0; EntryCnt < pDevice->RxPacketDescCnt; EntryCnt++)
+ {
+ pPacket = (PLM_PACKET) QQ_PopHead(&pDevice->RxPacketFreeQ.Container);
+ if (pPacket == 0)
+ break;
+
+ MM_FreeRxBuffer(pDevice, pPacket);
+
+ QQ_PushTail(&pDevice->RxPacketFreeQ.Container, pPacket);
+ }
+
+ LM_ResetChip(pDevice);
+
+ /* Restore PCI configuration registers. */
+ MM_WriteConfig32(pDevice, PCI_CACHE_LINE_SIZE_REG,
+ pDevice->SavedCacheLineReg);
+ LM_RegWrInd(pDevice, PCI_SUBSYSTEM_VENDOR_ID_REG,
+ (pDevice->SubsystemId << 16) | pDevice->SubsystemVendorId);
+
+ /* Reprogram the MAC address. */
+ LM_SetMacAddress(pDevice, pDevice->NodeAddress);
+
+ return LM_STATUS_SUCCESS;
+} /* LM_Halt */
+
+
+STATIC LM_STATUS
+LM_ResetChip(PLM_DEVICE_BLOCK pDevice)
+{
+ LM_UINT32 Value32;
+ LM_UINT32 j;
+
+ /* Wait for access to the nvram interface before resetting. This is */
+ /* a workaround to prevent EEPROM corruption. */
+ if(T3_ASIC_REV(pDevice->ChipRevId) != T3_ASIC_REV_5700 &&
+ T3_ASIC_REV(pDevice->ChipRevId) != T3_ASIC_REV_5701)
+ {
+ /* Request access to the flash interface. */
+ REG_WR(pDevice, Nvram.SwArb, SW_ARB_REQ_SET1);
+
+ for(j = 0; j < 100000; j++)
+ {
+ Value32 = REG_RD(pDevice, Nvram.SwArb);
+ if(Value32 & SW_ARB_GNT1)
+ {
+ break;
+ }
+ MM_Wait(10);
+ }
+ }
+
+ /* Global reset. */
+ REG_WR(pDevice, Grc.MiscCfg, GRC_MISC_CFG_CORE_CLOCK_RESET);
+ MM_Wait(40); MM_Wait(40); MM_Wait(40);
+
+ /* make sure we re-enable indirect accesses */
+ MM_WriteConfig32(pDevice, T3_PCI_MISC_HOST_CTRL_REG,
+ pDevice->MiscHostCtrl);
+
+ /* Set MAX PCI retry to zero. */
+ Value32 = T3_PCI_STATE_PCI_ROM_ENABLE | T3_PCI_STATE_PCI_ROM_RETRY_ENABLE;
+ if (pDevice->ChipRevId == T3_CHIP_ID_5704_A0)
+ {
+ if (!(pDevice->PciState & T3_PCI_STATE_CONVENTIONAL_PCI_MODE))
+ {
+ Value32 |= T3_PCI_STATE_RETRY_SAME_DMA;
+ }
+ }
+ MM_WriteConfig32(pDevice, T3_PCI_STATE_REG, Value32);
+
+ /* Restore PCI command register. */
+ MM_WriteConfig32(pDevice, PCI_COMMAND_REG,
+ pDevice->PciCommandStatusWords);
+
+ /* Disable PCI-X relaxed ordering bit. */
+ MM_ReadConfig32(pDevice, PCIX_CAP_REG, &Value32);
+ Value32 &= ~PCIX_ENABLE_RELAXED_ORDERING;
+ MM_WriteConfig32(pDevice, PCIX_CAP_REG, Value32);
+
+ /* Enable memory arbiter. */
+ REG_WR(pDevice, MemArbiter.Mode, T3_MEM_ARBITER_MODE_ENABLE);
+
+#ifdef BIG_ENDIAN_PCI /* This from jfd */
+ Value32 = GRC_MODE_WORD_SWAP_DATA|
+ GRC_MODE_WORD_SWAP_NON_FRAME_DATA;
+#else
+#ifdef BIG_ENDIAN_HOST
+ /* Reconfigure the mode register. */
+ Value32 = GRC_MODE_BYTE_SWAP_NON_FRAME_DATA |
+ GRC_MODE_WORD_SWAP_NON_FRAME_DATA |
+ GRC_MODE_BYTE_SWAP_DATA |
+ GRC_MODE_WORD_SWAP_DATA;
+#else
+ /* Reconfigure the mode register. */
+ Value32 = GRC_MODE_BYTE_SWAP_NON_FRAME_DATA | GRC_MODE_BYTE_SWAP_DATA;
+#endif
+#endif
+ REG_WR(pDevice, Grc.Mode, Value32);
+
+ /* Prevent PXE from restarting. */
+ MEM_WR_OFFSET(pDevice, 0x0b50, T3_MAGIC_NUM);
+
+ if(pDevice->EnableTbi) {
+ pDevice->MacMode = MAC_MODE_PORT_MODE_TBI;
+ REG_WR(pDevice, MacCtrl.Mode, MAC_MODE_PORT_MODE_TBI);
+ }
+ else {
+ REG_WR(pDevice, MacCtrl.Mode, 0);
+ }
+
+ /* Wait for the firmware to finish initialization. */
+ for(j = 0; j < 100000; j++)
+ {
+ MM_Wait(10);
+
+ Value32 = MEM_RD_OFFSET(pDevice, 0x0b50);
+ if(Value32 == ~T3_MAGIC_NUM)
+ {
+ break;
+ }
+ }
+ return LM_STATUS_SUCCESS;
+}
+
+/******************************************************************************/
+/* Description: */
+/* */
+/* Return: */
+/******************************************************************************/
+__inline static void
+LM_ServiceTxInterrupt(
+PLM_DEVICE_BLOCK pDevice) {
+ PLM_PACKET pPacket;
+ LM_UINT32 HwConIdx;
+ LM_UINT32 SwConIdx;
+
+ HwConIdx = pDevice->pStatusBlkVirt->Idx[0].SendConIdx;
+
+ /* Get our copy of the consumer index. The buffer descriptors */
+ /* that are in between the consumer indices are freed. */
+ SwConIdx = pDevice->SendConIdx;
+
+ /* Move the packets from the TxPacketActiveQ that are sent out to */
+ /* the TxPacketXmittedQ. Packets that are sent use the */
+ /* descriptors that are between SwConIdx and HwConIdx. */
+ while(SwConIdx != HwConIdx)
+ {
+ /* Get the packet that was sent from the TxPacketActiveQ. */
+ pPacket = (PLM_PACKET) QQ_PopHead(
+ &pDevice->TxPacketActiveQ.Container);
+
+ /* Set the return status. */
+ pPacket->PacketStatus = LM_STATUS_SUCCESS;
+
+ /* Put the packet in the TxPacketXmittedQ for indication later. */
+ QQ_PushTail(&pDevice->TxPacketXmittedQ.Container, pPacket);
+
+ /* Move to the next packet's BD. */
+ SwConIdx = (SwConIdx + pPacket->u.Tx.FragCount) &
+ T3_SEND_RCB_ENTRY_COUNT_MASK;
+
+ /* Update the number of unused BDs. */
+ atomic_add(pPacket->u.Tx.FragCount, &pDevice->SendBdLeft);
+
+ /* Get the new updated HwConIdx. */
+ HwConIdx = pDevice->pStatusBlkVirt->Idx[0].SendConIdx;
+ } /* while */
+
+ /* Save the new SwConIdx. */
+ pDevice->SendConIdx = SwConIdx;
+
+} /* LM_ServiceTxInterrupt */
+
+
+
+/******************************************************************************/
+/* Description: */
+/* */
+/* Return: */
+/******************************************************************************/
+__inline static void
+LM_ServiceRxInterrupt(
+PLM_DEVICE_BLOCK pDevice) {
+ PLM_PACKET pPacket;
+ PT3_RCV_BD pRcvBd;
+ LM_UINT32 HwRcvRetProdIdx;
+ LM_UINT32 SwRcvRetConIdx;
+
+ /* Loop thru the receive return rings for received packets. */
+ HwRcvRetProdIdx = pDevice->pStatusBlkVirt->Idx[0].RcvProdIdx;
+
+ SwRcvRetConIdx = pDevice->RcvRetConIdx;
+ while(SwRcvRetConIdx != HwRcvRetProdIdx)
+ {
+ pRcvBd = &pDevice->pRcvRetBdVirt[SwRcvRetConIdx];
+
+ /* Get the received packet descriptor. */
+ pPacket = (PLM_PACKET) (MM_UINT_PTR(pDevice->pPacketDescBase) +
+ MM_UINT_PTR(pRcvBd->Opaque));
+
+ /* Check the error flag. */
+ if(pRcvBd->ErrorFlag &&
+ pRcvBd->ErrorFlag != RCV_BD_ERR_ODD_NIBBLED_RCVD_MII)
+ {
+ pPacket->PacketStatus = LM_STATUS_FAILURE;
+
+ pDevice->RxCounters.RxPacketErrCnt++;
+
+ if(pRcvBd->ErrorFlag & RCV_BD_ERR_BAD_CRC)
+ {
+ pDevice->RxCounters.RxErrCrcCnt++;
+ }
+
+ if(pRcvBd->ErrorFlag & RCV_BD_ERR_COLL_DETECT)
+ {
+ pDevice->RxCounters.RxErrCollCnt++;
+ }
+
+ if(pRcvBd->ErrorFlag & RCV_BD_ERR_LINK_LOST_DURING_PKT)
+ {
+ pDevice->RxCounters.RxErrLinkLostCnt++;
+ }
+
+ if(pRcvBd->ErrorFlag & RCV_BD_ERR_PHY_DECODE_ERR)
+ {
+ pDevice->RxCounters.RxErrPhyDecodeCnt++;
+ }
+
+ if(pRcvBd->ErrorFlag & RCV_BD_ERR_ODD_NIBBLED_RCVD_MII)
+ {
+ pDevice->RxCounters.RxErrOddNibbleCnt++;
+ }
+
+ if(pRcvBd->ErrorFlag & RCV_BD_ERR_MAC_ABORT)
+ {
+ pDevice->RxCounters.RxErrMacAbortCnt++;
+ }
+
+ if(pRcvBd->ErrorFlag & RCV_BD_ERR_LEN_LT_64)
+ {
+ pDevice->RxCounters.RxErrShortPacketCnt++;
+ }
+
+ if(pRcvBd->ErrorFlag & RCV_BD_ERR_TRUNC_NO_RESOURCES)
+ {
+ pDevice->RxCounters.RxErrNoResourceCnt++;
+ }
+
+ if(pRcvBd->ErrorFlag & RCV_BD_ERR_GIANT_FRAME_RCVD)
+ {
+ pDevice->RxCounters.RxErrLargePacketCnt++;
+ }
+ }
+ else
+ {
+ pPacket->PacketStatus = LM_STATUS_SUCCESS;
+ pPacket->PacketSize = pRcvBd->Len - 4;
+
+ pPacket->Flags = pRcvBd->Flags;
+ if(pRcvBd->Flags & RCV_BD_FLAG_VLAN_TAG)
+ {
+ pPacket->VlanTag = pRcvBd->VlanTag;
+ }
+
+ pPacket->u.Rx.TcpUdpChecksum = pRcvBd->TcpUdpCksum;
+ }
+
+ /* Put the packet descriptor containing the received packet */
+ /* buffer in the RxPacketReceivedQ for indication later. */
+ QQ_PushTail(&pDevice->RxPacketReceivedQ.Container, pPacket);
+
+ /* Go to the next buffer descriptor. */
+ SwRcvRetConIdx = (SwRcvRetConIdx + 1) &
+ T3_RCV_RETURN_RCB_ENTRY_COUNT_MASK;
+
+ /* Get the updated HwRcvRetProdIdx. */
+ HwRcvRetProdIdx = pDevice->pStatusBlkVirt->Idx[0].RcvProdIdx;
+ } /* while */
+
+ pDevice->RcvRetConIdx = SwRcvRetConIdx;
+
+ /* Update the receive return ring consumer index. */
+ MB_REG_WR(pDevice, Mailbox.RcvRetConIdx[0].Low, SwRcvRetConIdx);
+} /* LM_ServiceRxInterrupt */
+
+
+
+/******************************************************************************/
+/* Description: */
+/* This is the interrupt event handler routine. It acknowledges all */
+/* pending interrupts and process all pending events. */
+/* */
+/* Return: */
+/* LM_STATUS_SUCCESS */
+/******************************************************************************/
+LM_STATUS
+LM_ServiceInterrupts(
+ PLM_DEVICE_BLOCK pDevice)
+{
+ LM_UINT32 Value32;
+ int ServicePhyInt = FALSE;
+
+ /* Setup the phy chip whenever the link status changes. */
+ if(pDevice->LinkChngMode == T3_LINK_CHNG_MODE_USE_STATUS_REG)
+ {
+ Value32 = REG_RD(pDevice, MacCtrl.Status);
+ if(pDevice->PhyIntMode == T3_PHY_INT_MODE_MI_INTERRUPT)
+ {
+ if (Value32 & MAC_STATUS_MI_INTERRUPT)
+ {
+ ServicePhyInt = TRUE;
+ }
+ }
+ else if(Value32 & MAC_STATUS_LINK_STATE_CHANGED)
+ {
+ ServicePhyInt = TRUE;
+ }
+ }
+ else
+ {
+ if(pDevice->pStatusBlkVirt->Status & STATUS_BLOCK_LINK_CHANGED_STATUS)
+ {
+ pDevice->pStatusBlkVirt->Status = STATUS_BLOCK_UPDATED |
+ (pDevice->pStatusBlkVirt->Status & ~STATUS_BLOCK_LINK_CHANGED_STATUS);
+ ServicePhyInt = TRUE;
+ }
+ }
+#if INCLUDE_TBI_SUPPORT
+ if (pDevice->IgnoreTbiLinkChange == TRUE)
+ {
+ ServicePhyInt = FALSE;
+ }
+#endif
+ if (ServicePhyInt == TRUE)
+ {
+ LM_SetupPhy(pDevice);
+ }
+
+ /* Service receive and transmit interrupts. */
+ LM_ServiceRxInterrupt(pDevice);
+ LM_ServiceTxInterrupt(pDevice);
+
+ /* No spinlock for this queue since this routine is serialized. */
+ if(!QQ_Empty(&pDevice->RxPacketReceivedQ.Container))
+ {
+ /* Indicate receive packets. */
+ MM_IndicateRxPackets(pDevice);
+ /* LM_QueueRxPackets(pDevice); */
+ }
+
+ /* No spinlock for this queue since this routine is serialized. */
+ if(!QQ_Empty(&pDevice->TxPacketXmittedQ.Container))
+ {
+ MM_IndicateTxPackets(pDevice);
+ }
+
+ return LM_STATUS_SUCCESS;
+} /* LM_ServiceInterrupts */
+
+
+
+/******************************************************************************/
+/* Description: */
+/* */
+/* Return: */
+/******************************************************************************/
+LM_STATUS
+LM_MulticastAdd(
+PLM_DEVICE_BLOCK pDevice,
+PLM_UINT8 pMcAddress) {
+ PLM_UINT8 pEntry;
+ LM_UINT32 j;
+
+ pEntry = pDevice->McTable[0];
+ for(j = 0; j < pDevice->McEntryCount; j++)
+ {
+ if(IS_ETH_ADDRESS_EQUAL(pEntry, pMcAddress))
+ {
+ /* Found a match, increment the instance count. */
+ pEntry[LM_MC_INSTANCE_COUNT_INDEX] += 1;
+
+ return LM_STATUS_SUCCESS;
+ }
+
+ pEntry += LM_MC_ENTRY_SIZE;
+ }
+
+ if(pDevice->McEntryCount >= LM_MAX_MC_TABLE_SIZE)
+ {
+ return LM_STATUS_FAILURE;
+ }
+
+ pEntry = pDevice->McTable[pDevice->McEntryCount];
+
+ COPY_ETH_ADDRESS(pMcAddress, pEntry);
+ pEntry[LM_MC_INSTANCE_COUNT_INDEX] = 1;
+
+ pDevice->McEntryCount++;
+
+ LM_SetReceiveMask(pDevice, pDevice->ReceiveMask | LM_ACCEPT_MULTICAST);
+
+ return LM_STATUS_SUCCESS;
+} /* LM_MulticastAdd */
+
+
+
+/******************************************************************************/
+/* Description: */
+/* */
+/* Return: */
+/******************************************************************************/
+LM_STATUS
+LM_MulticastDel(
+PLM_DEVICE_BLOCK pDevice,
+PLM_UINT8 pMcAddress) {
+ PLM_UINT8 pEntry;
+ LM_UINT32 j;
+
+ pEntry = pDevice->McTable[0];
+ for(j = 0; j < pDevice->McEntryCount; j++)
+ {
+ if(IS_ETH_ADDRESS_EQUAL(pEntry, pMcAddress))
+ {
+ /* Found a match, decrement the instance count. */
+ pEntry[LM_MC_INSTANCE_COUNT_INDEX] -= 1;
+
+ /* No more instance left, remove the address from the table. */
+ /* Move the last entry in the table to the delete slot. */
+ if(pEntry[LM_MC_INSTANCE_COUNT_INDEX] == 0 &&
+ pDevice->McEntryCount > 1)
+ {
+
+ COPY_ETH_ADDRESS(
+ pDevice->McTable[pDevice->McEntryCount-1], pEntry);
+ pEntry[LM_MC_INSTANCE_COUNT_INDEX] =
+ pDevice->McTable[pDevice->McEntryCount-1]
+ [LM_MC_INSTANCE_COUNT_INDEX];
+ }
+ pDevice->McEntryCount--;
+
+ /* Update the receive mask if the table is empty. */
+ if(pDevice->McEntryCount == 0)
+ {
+ LM_SetReceiveMask(pDevice,
+ pDevice->ReceiveMask & ~LM_ACCEPT_MULTICAST);
+ }
+
+ return LM_STATUS_SUCCESS;
+ }
+
+ pEntry += LM_MC_ENTRY_SIZE;
+ }
+
+ return LM_STATUS_FAILURE;
+} /* LM_MulticastDel */
+
+
+
+/******************************************************************************/
+/* Description: */
+/* */
+/* Return: */
+/******************************************************************************/
+LM_STATUS
+LM_MulticastClear(
+PLM_DEVICE_BLOCK pDevice) {
+ pDevice->McEntryCount = 0;
+
+ LM_SetReceiveMask(pDevice, pDevice->ReceiveMask & ~LM_ACCEPT_MULTICAST);
+
+ return LM_STATUS_SUCCESS;
+} /* LM_MulticastClear */
+
+
+
+/******************************************************************************/
+/* Description: */
+/* */
+/* Return: */
+/******************************************************************************/
+LM_STATUS
+LM_SetMacAddress(
+ PLM_DEVICE_BLOCK pDevice,
+ PLM_UINT8 pMacAddress)
+{
+ LM_UINT32 j;
+
+ for(j = 0; j < 4; j++)
+ {
+ REG_WR(pDevice, MacCtrl.MacAddr[j].High,
+ (pMacAddress[0] << 8) | pMacAddress[1]);
+ REG_WR(pDevice, MacCtrl.MacAddr[j].Low,
+ (pMacAddress[2] << 24) | (pMacAddress[3] << 16) |
+ (pMacAddress[4] << 8) | pMacAddress[5]);
+ }
+
+ return LM_STATUS_SUCCESS;
+}
+
+
+/******************************************************************************/
+/* Description: */
+/* Sets up the default line speed, and duplex modes based on the requested */
+/* media type. */
+/* */
+/* Return: */
+/* None. */
+/******************************************************************************/
+static LM_STATUS
+LM_TranslateRequestedMediaType(
+LM_REQUESTED_MEDIA_TYPE RequestedMediaType,
+PLM_MEDIA_TYPE pMediaType,
+PLM_LINE_SPEED pLineSpeed,
+PLM_DUPLEX_MODE pDuplexMode) {
+ *pMediaType = LM_MEDIA_TYPE_AUTO;
+ *pLineSpeed = LM_LINE_SPEED_UNKNOWN;
+ *pDuplexMode = LM_DUPLEX_MODE_UNKNOWN;
+
+ /* determine media type */
+ switch(RequestedMediaType) {
+ case LM_REQUESTED_MEDIA_TYPE_BNC:
+ *pMediaType = LM_MEDIA_TYPE_BNC;
+ *pLineSpeed = LM_LINE_SPEED_10MBPS;
+ *pDuplexMode = LM_DUPLEX_MODE_HALF;
+ break;
+
+ case LM_REQUESTED_MEDIA_TYPE_UTP_AUTO:
+ *pMediaType = LM_MEDIA_TYPE_UTP;
+ break;
+
+ case LM_REQUESTED_MEDIA_TYPE_UTP_10MBPS:
+ *pMediaType = LM_MEDIA_TYPE_UTP;
+ *pLineSpeed = LM_LINE_SPEED_10MBPS;
+ *pDuplexMode = LM_DUPLEX_MODE_HALF;
+ break;
+
+ case LM_REQUESTED_MEDIA_TYPE_UTP_10MBPS_FULL_DUPLEX:
+ *pMediaType = LM_MEDIA_TYPE_UTP;
+ *pLineSpeed = LM_LINE_SPEED_10MBPS;
+ *pDuplexMode = LM_DUPLEX_MODE_FULL;
+ break;
+
+ case LM_REQUESTED_MEDIA_TYPE_UTP_100MBPS:
+ *pMediaType = LM_MEDIA_TYPE_UTP;
+ *pLineSpeed = LM_LINE_SPEED_100MBPS;
+ *pDuplexMode = LM_DUPLEX_MODE_HALF;
+ break;
+
+ case LM_REQUESTED_MEDIA_TYPE_UTP_100MBPS_FULL_DUPLEX:
+ *pMediaType = LM_MEDIA_TYPE_UTP;
+ *pLineSpeed = LM_LINE_SPEED_100MBPS;
+ *pDuplexMode = LM_DUPLEX_MODE_FULL;
+ break;
+
+ case LM_REQUESTED_MEDIA_TYPE_UTP_1000MBPS:
+ *pMediaType = LM_MEDIA_TYPE_UTP;
+ *pLineSpeed = LM_LINE_SPEED_1000MBPS;
+ *pDuplexMode = LM_DUPLEX_MODE_HALF;
+ break;
+
+ case LM_REQUESTED_MEDIA_TYPE_UTP_1000MBPS_FULL_DUPLEX:
+ *pMediaType = LM_MEDIA_TYPE_UTP;
+ *pLineSpeed = LM_LINE_SPEED_1000MBPS;
+ *pDuplexMode = LM_DUPLEX_MODE_FULL;
+ break;
+
+ case LM_REQUESTED_MEDIA_TYPE_FIBER_100MBPS:
+ *pMediaType = LM_MEDIA_TYPE_FIBER;
+ *pLineSpeed = LM_LINE_SPEED_100MBPS;
+ *pDuplexMode = LM_DUPLEX_MODE_HALF;
+ break;
+
+ case LM_REQUESTED_MEDIA_TYPE_FIBER_100MBPS_FULL_DUPLEX:
+ *pMediaType = LM_MEDIA_TYPE_FIBER;
+ *pLineSpeed = LM_LINE_SPEED_100MBPS;
+ *pDuplexMode = LM_DUPLEX_MODE_FULL;
+ break;
+
+ case LM_REQUESTED_MEDIA_TYPE_FIBER_1000MBPS:
+ *pMediaType = LM_MEDIA_TYPE_FIBER;
+ *pLineSpeed = LM_LINE_SPEED_1000MBPS;
+ *pDuplexMode = LM_DUPLEX_MODE_HALF;
+ break;
+
+ case LM_REQUESTED_MEDIA_TYPE_FIBER_1000MBPS_FULL_DUPLEX:
+ *pMediaType = LM_MEDIA_TYPE_FIBER;
+ *pLineSpeed = LM_LINE_SPEED_1000MBPS;
+ *pDuplexMode = LM_DUPLEX_MODE_FULL;
+ break;
+
+ default:
+ break;
+ } /* switch */
+
+ return LM_STATUS_SUCCESS;
+} /* LM_TranslateRequestedMediaType */
+
+/******************************************************************************/
+/* Description: */
+/* */
+/* Return: */
+/* LM_STATUS_LINK_ACTIVE */
+/* LM_STATUS_LINK_DOWN */
+/******************************************************************************/
+static LM_STATUS
+LM_InitBcm540xPhy(
+PLM_DEVICE_BLOCK pDevice)
+{
+ LM_LINE_SPEED CurrentLineSpeed;
+ LM_DUPLEX_MODE CurrentDuplexMode;
+ LM_STATUS CurrentLinkStatus;
+ LM_UINT32 Value32;
+ LM_UINT32 j;
+
+#if 1 /* jmb: bugfix -- moved here, out of code that sets initial pwr state */
+ LM_WritePhy(pDevice, BCM5401_AUX_CTRL, 0x2);
+#endif
+ if((pDevice->PhyId & PHY_ID_MASK) == PHY_BCM5401_PHY_ID)
+ {
+ LM_ReadPhy(pDevice, PHY_STATUS_REG, &Value32);
+ LM_ReadPhy(pDevice, PHY_STATUS_REG, &Value32);
+
+ if(!pDevice->InitDone)
+ {
+ Value32 = 0;
+ }
+
+ if(!(Value32 & PHY_STATUS_LINK_PASS))
+ {
+ LM_WritePhy(pDevice, BCM5401_AUX_CTRL, 0x0c20);
+
+ LM_WritePhy(pDevice, BCM540X_DSP_ADDRESS_REG, 0x0012);
+ LM_WritePhy(pDevice, BCM540X_DSP_RW_PORT, 0x1804);
+
+ LM_WritePhy(pDevice, BCM540X_DSP_ADDRESS_REG, 0x0013);
+ LM_WritePhy(pDevice, BCM540X_DSP_RW_PORT, 0x1204);
+
+ LM_WritePhy(pDevice, BCM540X_DSP_ADDRESS_REG, 0x8006);
+ LM_WritePhy(pDevice, BCM540X_DSP_RW_PORT, 0x0132);
+
+ LM_WritePhy(pDevice, BCM540X_DSP_ADDRESS_REG, 0x8006);
+ LM_WritePhy(pDevice, BCM540X_DSP_RW_PORT, 0x0232);
+
+ LM_WritePhy(pDevice, BCM540X_DSP_ADDRESS_REG, 0x201f);
+ LM_WritePhy(pDevice, BCM540X_DSP_RW_PORT, 0x0a20);
+
+ LM_ReadPhy(pDevice, PHY_STATUS_REG, &Value32);
+ for(j = 0; j < 1000; j++)
+ {
+ MM_Wait(10);
+
+ LM_ReadPhy(pDevice, PHY_STATUS_REG, &Value32);
+ if(Value32 & PHY_STATUS_LINK_PASS)
+ {
+ MM_Wait(40);
+ break;
+ }
+ }
+
+ if((pDevice->PhyId & PHY_ID_REV_MASK) == PHY_BCM5401_B0_REV)
+ {
+ if(!(Value32 & PHY_STATUS_LINK_PASS) &&
+ (pDevice->OldLineSpeed == LM_LINE_SPEED_1000MBPS))
+ {
+ LM_WritePhy(pDevice, PHY_CTRL_REG, PHY_CTRL_PHY_RESET);
+ for(j = 0; j < 100; j++)
+ {
+ MM_Wait(10);
+
+ LM_ReadPhy(pDevice, PHY_CTRL_REG, &Value32);
+ if(!(Value32 & PHY_CTRL_PHY_RESET))
+ {
+ MM_Wait(40);
+ break;
+ }
+ }
+
+ LM_WritePhy(pDevice, BCM5401_AUX_CTRL, 0x0c20);
+
+ LM_WritePhy(pDevice, BCM540X_DSP_ADDRESS_REG, 0x0012);
+ LM_WritePhy(pDevice, BCM540X_DSP_RW_PORT, 0x1804);
+
+ LM_WritePhy(pDevice, BCM540X_DSP_ADDRESS_REG, 0x0013);
+ LM_WritePhy(pDevice, BCM540X_DSP_RW_PORT, 0x1204);
+
+ LM_WritePhy(pDevice, BCM540X_DSP_ADDRESS_REG, 0x8006);
+ LM_WritePhy(pDevice, BCM540X_DSP_RW_PORT, 0x0132);
+
+ LM_WritePhy(pDevice, BCM540X_DSP_ADDRESS_REG, 0x8006);
+ LM_WritePhy(pDevice, BCM540X_DSP_RW_PORT, 0x0232);
+
+ LM_WritePhy(pDevice, BCM540X_DSP_ADDRESS_REG, 0x201f);
+ LM_WritePhy(pDevice, BCM540X_DSP_RW_PORT, 0x0a20);
+ }
+ }
+ }
+ }
+ else if(pDevice->ChipRevId == T3_CHIP_ID_5701_A0 ||
+ pDevice->ChipRevId == T3_CHIP_ID_5701_B0)
+ {
+ /* Bug: 5701 A0, B0 TX CRC workaround. */
+ LM_WritePhy(pDevice, 0x15, 0x0a75);
+ LM_WritePhy(pDevice, 0x1c, 0x8c68);
+ LM_WritePhy(pDevice, 0x1c, 0x8d68);
+ LM_WritePhy(pDevice, 0x1c, 0x8c68);
+ }
+
+ /* Acknowledge interrupts. */
+ LM_ReadPhy(pDevice, BCM540X_INT_STATUS_REG, &Value32);
+ LM_ReadPhy(pDevice, BCM540X_INT_STATUS_REG, &Value32);
+
+ /* Configure the interrupt mask. */
+ if(pDevice->PhyIntMode == T3_PHY_INT_MODE_MI_INTERRUPT)
+ {
+ LM_WritePhy(pDevice, BCM540X_INT_MASK_REG, ~BCM540X_INT_LINK_CHANGE);
+ }
+
+ /* Configure PHY led mode. */
+ if(T3_ASIC_REV(pDevice->ChipRevId) == T3_ASIC_REV_5701 ||
+ (T3_ASIC_REV(pDevice->ChipRevId) == T3_ASIC_REV_5700))
+ {
+ if(pDevice->LedMode == LED_MODE_THREE_LINK)
+ {
+ LM_WritePhy(pDevice, BCM540X_EXT_CTRL_REG,
+ BCM540X_EXT_CTRL_LINK3_LED_MODE);
+ }
+ else
+ {
+ LM_WritePhy(pDevice, BCM540X_EXT_CTRL_REG, 0);
+ }
+ }
+
+ CurrentLinkStatus = LM_STATUS_LINK_DOWN;
+
+ /* Get current link and duplex mode. */
+ for(j = 0; j < 100; j++)
+ {
+ LM_ReadPhy(pDevice, PHY_STATUS_REG, &Value32);
+ LM_ReadPhy(pDevice, PHY_STATUS_REG, &Value32);
+
+ if(Value32 & PHY_STATUS_LINK_PASS)
+ {
+ break;
+ }
+ MM_Wait(40);
+ }
+
+ if(Value32 & PHY_STATUS_LINK_PASS)
+ {
+
+ /* Determine the current line and duplex settings. */
+ LM_ReadPhy(pDevice, BCM540X_AUX_STATUS_REG, &Value32);
+ for(j = 0; j < 2000; j++)
+ {
+ MM_Wait(10);
+
+ LM_ReadPhy(pDevice, BCM540X_AUX_STATUS_REG, &Value32);
+ if(Value32)
+ {
+ break;
+ }
+ }
+
+ switch(Value32 & BCM540X_AUX_SPEED_MASK)
+ {
+ case BCM540X_AUX_10BASET_HD:
+ CurrentLineSpeed = LM_LINE_SPEED_10MBPS;
+ CurrentDuplexMode = LM_DUPLEX_MODE_HALF;
+ break;
+
+ case BCM540X_AUX_10BASET_FD:
+ CurrentLineSpeed = LM_LINE_SPEED_10MBPS;
+ CurrentDuplexMode = LM_DUPLEX_MODE_FULL;
+ break;
+
+ case BCM540X_AUX_100BASETX_HD:
+ CurrentLineSpeed = LM_LINE_SPEED_100MBPS;
+ CurrentDuplexMode = LM_DUPLEX_MODE_HALF;
+ break;
+
+ case BCM540X_AUX_100BASETX_FD:
+ CurrentLineSpeed = LM_LINE_SPEED_100MBPS;
+ CurrentDuplexMode = LM_DUPLEX_MODE_FULL;
+ break;
+
+ case BCM540X_AUX_100BASET_HD:
+ CurrentLineSpeed = LM_LINE_SPEED_1000MBPS;
+ CurrentDuplexMode = LM_DUPLEX_MODE_HALF;
+ break;
+
+ case BCM540X_AUX_100BASET_FD:
+ CurrentLineSpeed = LM_LINE_SPEED_1000MBPS;
+ CurrentDuplexMode = LM_DUPLEX_MODE_FULL;
+ break;
+
+ default:
+
+ CurrentLineSpeed = LM_LINE_SPEED_UNKNOWN;
+ CurrentDuplexMode = LM_DUPLEX_MODE_UNKNOWN;
+ break;
+ }
+
+ /* Make sure we are in auto-neg mode. */
+ for (j = 0; j < 200; j++)
+ {
+ LM_ReadPhy(pDevice, PHY_CTRL_REG, &Value32);
+ if(Value32 && Value32 != 0x7fff)
+ {
+ break;
+ }
+
+ if(Value32 == 0 && pDevice->RequestedMediaType ==
+ LM_REQUESTED_MEDIA_TYPE_UTP_10MBPS)
+ {
+ break;
+ }
+
+ MM_Wait(10);
+ }
+
+ /* Use the current line settings for "auto" mode. */
+ if(pDevice->RequestedMediaType == LM_REQUESTED_MEDIA_TYPE_AUTO ||
+ pDevice->RequestedMediaType == LM_REQUESTED_MEDIA_TYPE_UTP_AUTO)
+ {
+ if(Value32 & PHY_CTRL_AUTO_NEG_ENABLE)
+ {
+ CurrentLinkStatus = LM_STATUS_LINK_ACTIVE;
+
+ /* We may be exiting low power mode and the link is in */
+ /* 10mb. In this case, we need to restart autoneg. */
+ LM_ReadPhy(pDevice, BCM540X_1000BASET_CTRL_REG, &Value32);
+ pDevice->advertising1000 = Value32;
+ /* 5702FE supports 10/100Mb only. */
+ if(T3_ASIC_REV(pDevice->ChipRevId) != T3_ASIC_REV_5703 ||
+ pDevice->BondId != GRC_MISC_BD_ID_5702FE)
+ {
+ if(!(Value32 & (BCM540X_AN_AD_1000BASET_HALF |
+ BCM540X_AN_AD_1000BASET_FULL)))
+ {
+ CurrentLinkStatus = LM_STATUS_LINK_SETTING_MISMATCH;
+ }
+ }
+ }
+ else
+ {
+ CurrentLinkStatus = LM_STATUS_LINK_SETTING_MISMATCH;
+ }
+ }
+ else
+ {
+ /* Force line settings. */
+ /* Use the current setting if it matches the user's requested */
+ /* setting. */
+ LM_ReadPhy(pDevice, PHY_CTRL_REG, &Value32);
+ if((pDevice->LineSpeed == CurrentLineSpeed) &&
+ (pDevice->DuplexMode == CurrentDuplexMode))
+ {
+ if ((pDevice->DisableAutoNeg &&
+ !(Value32 & PHY_CTRL_AUTO_NEG_ENABLE)) ||
+ (!pDevice->DisableAutoNeg &&
+ (Value32 & PHY_CTRL_AUTO_NEG_ENABLE)))
+ {
+ CurrentLinkStatus = LM_STATUS_LINK_ACTIVE;
+ }
+ else
+ {
+ CurrentLinkStatus = LM_STATUS_LINK_SETTING_MISMATCH;
+ }
+ }
+ else
+ {
+ CurrentLinkStatus = LM_STATUS_LINK_SETTING_MISMATCH;
+ }
+ }
+
+ /* Save line settings. */
+ pDevice->LineSpeed = CurrentLineSpeed;
+ pDevice->DuplexMode = CurrentDuplexMode;
+ pDevice->MediaType = LM_MEDIA_TYPE_UTP;
+ }
+
+ return CurrentLinkStatus;
+} /* LM_InitBcm540xPhy */
+
+/******************************************************************************/
+/* Description: */
+/* */
+/* Return: */
+/******************************************************************************/
+LM_STATUS
+LM_SetFlowControl(
+ PLM_DEVICE_BLOCK pDevice,
+ LM_UINT32 LocalPhyAd,
+ LM_UINT32 RemotePhyAd)
+{
+ LM_FLOW_CONTROL FlowCap;
+
+ /* Resolve flow control. */
+ FlowCap = LM_FLOW_CONTROL_NONE;
+
+ /* See Table 28B-3 of 802.3ab-1999 spec. */
+ if(pDevice->FlowControlCap & LM_FLOW_CONTROL_AUTO_PAUSE)
+ {
+ if(LocalPhyAd & PHY_AN_AD_PAUSE_CAPABLE)
+ {
+ if(LocalPhyAd & PHY_AN_AD_ASYM_PAUSE)
+ {
+ if(RemotePhyAd & PHY_LINK_PARTNER_PAUSE_CAPABLE)
+ {
+ FlowCap = LM_FLOW_CONTROL_TRANSMIT_PAUSE |
+ LM_FLOW_CONTROL_RECEIVE_PAUSE;
+ }
+ else if(RemotePhyAd & PHY_LINK_PARTNER_ASYM_PAUSE)
+ {
+ FlowCap = LM_FLOW_CONTROL_RECEIVE_PAUSE;
+ }
+ }
+ else
+ {
+ if(RemotePhyAd & PHY_LINK_PARTNER_PAUSE_CAPABLE)
+ {
+ FlowCap = LM_FLOW_CONTROL_TRANSMIT_PAUSE |
+ LM_FLOW_CONTROL_RECEIVE_PAUSE;
+ }
+ }
+ }
+ else if(LocalPhyAd & PHY_AN_AD_ASYM_PAUSE)
+ {
+ if((RemotePhyAd & PHY_LINK_PARTNER_PAUSE_CAPABLE) &&
+ (RemotePhyAd & PHY_LINK_PARTNER_ASYM_PAUSE))
+ {
+ FlowCap = LM_FLOW_CONTROL_TRANSMIT_PAUSE;
+ }
+ }
+ }
+ else
+ {
+ FlowCap = pDevice->FlowControlCap;
+ }
+
+ /* Enable/disable rx PAUSE. */
+ pDevice->RxMode &= ~RX_MODE_ENABLE_FLOW_CONTROL;
+ if(FlowCap & LM_FLOW_CONTROL_RECEIVE_PAUSE &&
+ (pDevice->FlowControlCap == LM_FLOW_CONTROL_AUTO_PAUSE ||
+ pDevice->FlowControlCap & LM_FLOW_CONTROL_RECEIVE_PAUSE))
+ {
+ pDevice->FlowControl |= LM_FLOW_CONTROL_RECEIVE_PAUSE;
+ pDevice->RxMode |= RX_MODE_ENABLE_FLOW_CONTROL;
+
+ }
+ REG_WR(pDevice, MacCtrl.RxMode, pDevice->RxMode);
+
+ /* Enable/disable tx PAUSE. */
+ pDevice->TxMode &= ~TX_MODE_ENABLE_FLOW_CONTROL;
+ if(FlowCap & LM_FLOW_CONTROL_TRANSMIT_PAUSE &&
+ (pDevice->FlowControlCap == LM_FLOW_CONTROL_AUTO_PAUSE ||
+ pDevice->FlowControlCap & LM_FLOW_CONTROL_TRANSMIT_PAUSE))
+ {
+ pDevice->FlowControl |= LM_FLOW_CONTROL_TRANSMIT_PAUSE;
+ pDevice->TxMode |= TX_MODE_ENABLE_FLOW_CONTROL;
+
+ }
+ REG_WR(pDevice, MacCtrl.TxMode, pDevice->TxMode);
+
+ return LM_STATUS_SUCCESS;
+}
+
+
+#if INCLUDE_TBI_SUPPORT
+/******************************************************************************/
+/* Description: */
+/* */
+/* Return: */
+/******************************************************************************/
+STATIC LM_STATUS
+LM_InitBcm800xPhy(
+ PLM_DEVICE_BLOCK pDevice)
+{
+ LM_UINT32 Value32;
+ LM_UINT32 j;
+
+ Value32 = REG_RD(pDevice, MacCtrl.Status);
+
+ /* Reset the SERDES during init and when we have link. */
+ if(!pDevice->InitDone || Value32 & MAC_STATUS_PCS_SYNCED)
+ {
+ /* Set PLL lock range. */
+ LM_WritePhy(pDevice, 0x16, 0x8007);
+
+ /* Software reset. */
+ LM_WritePhy(pDevice, 0x00, 0x8000);
+
+ /* Wait for reset to complete. */
+ for(j = 0; j < 500; j++)
+ {
+ MM_Wait(10);
+ }
+
+ /* Config mode; seletct PMA/Ch 1 regs. */
+ LM_WritePhy(pDevice, 0x10, 0x8411);
+
+ /* Enable auto-lock and comdet, select txclk for tx. */
+ LM_WritePhy(pDevice, 0x11, 0x0a10);
+
+ LM_WritePhy(pDevice, 0x18, 0x00a0);
+ LM_WritePhy(pDevice, 0x16, 0x41ff);
+
+ /* Assert and deassert POR. */
+ LM_WritePhy(pDevice, 0x13, 0x0400);
+ MM_Wait(40);
+ LM_WritePhy(pDevice, 0x13, 0x0000);
+
+ LM_WritePhy(pDevice, 0x11, 0x0a50);
+ MM_Wait(40);
+ LM_WritePhy(pDevice, 0x11, 0x0a10);
+
+ /* Delay for signal to stabilize. */
+ for(j = 0; j < 15000; j++)
+ {
+ MM_Wait(10);
+ }
+
+ /* Deselect the channel register so we can read the PHY id later. */
+ LM_WritePhy(pDevice, 0x10, 0x8011);
+ }
+
+ return LM_STATUS_SUCCESS;
+}
+
+
+
+/******************************************************************************/
+/* Description: */
+/* */
+/* Return: */
+/******************************************************************************/
+STATIC LM_STATUS
+LM_SetupFiberPhy(
+ PLM_DEVICE_BLOCK pDevice)
+{
+ LM_STATUS CurrentLinkStatus;
+ AUTONEG_STATUS AnStatus = 0;
+ LM_UINT32 Value32;
+ LM_UINT32 Cnt;
+ LM_UINT32 j, k;
+
+ pDevice->MacMode &= ~(MAC_MODE_HALF_DUPLEX | MAC_MODE_PORT_MODE_MASK);
+
+ /* Initialize the send_config register. */
+ REG_WR(pDevice, MacCtrl.TxAutoNeg, 0);
+
+ /* Enable TBI and full duplex mode. */
+ pDevice->MacMode |= MAC_MODE_PORT_MODE_TBI;
+ REG_WR(pDevice, MacCtrl.Mode, pDevice->MacMode);
+
+ /* Initialize the BCM8002 SERDES PHY. */
+ switch(pDevice->PhyId & PHY_ID_MASK)
+ {
+ case PHY_BCM8002_PHY_ID:
+ LM_InitBcm800xPhy(pDevice);
+ break;
+
+ default:
+ break;
+ }
+
+ /* Enable link change interrupt. */
+ REG_WR(pDevice, MacCtrl.MacEvent, MAC_EVENT_ENABLE_LINK_STATE_CHANGED_ATTN);
+
+ /* Default to link down. */
+ CurrentLinkStatus = LM_STATUS_LINK_DOWN;
+
+ /* Get the link status. */
+ Value32 = REG_RD(pDevice, MacCtrl.Status);
+ if(Value32 & MAC_STATUS_PCS_SYNCED)
+ {
+ if((pDevice->RequestedMediaType == LM_REQUESTED_MEDIA_TYPE_AUTO) ||
+ (pDevice->DisableAutoNeg == FALSE))
+ {
+ /* auto-negotiation mode. */
+ /* Initialize the autoneg default capaiblities. */
+ AutonegInit(&pDevice->AnInfo);
+
+ /* Set the context pointer to point to the main device structure. */
+ pDevice->AnInfo.pContext = pDevice;
+
+ /* Setup flow control advertisement register. */
+ Value32 = GetPhyAdFlowCntrlSettings(pDevice);
+ if(Value32 & PHY_AN_AD_PAUSE_CAPABLE)
+ {
+ pDevice->AnInfo.mr_adv_sym_pause = 1;
+ }
+ else
+ {
+ pDevice->AnInfo.mr_adv_sym_pause = 0;
+ }
+
+ if(Value32 & PHY_AN_AD_ASYM_PAUSE)
+ {
+ pDevice->AnInfo.mr_adv_asym_pause = 1;
+ }
+ else
+ {
+ pDevice->AnInfo.mr_adv_asym_pause = 0;
+ }
+
+ /* Try to autoneg up to six times. */
+ if (pDevice->IgnoreTbiLinkChange)
+ {
+ Cnt = 1;
+ }
+ else
+ {
+ Cnt = 6;
+ }
+ for (j = 0; j < Cnt; j++)
+ {
+ REG_WR(pDevice, MacCtrl.TxAutoNeg, 0);
+
+ Value32 = pDevice->MacMode & ~MAC_MODE_PORT_MODE_MASK;
+ REG_WR(pDevice, MacCtrl.Mode, Value32);
+ MM_Wait(20);
+
+ REG_WR(pDevice, MacCtrl.Mode, pDevice->MacMode |
+ MAC_MODE_SEND_CONFIGS);
+
+ MM_Wait(20);
+
+ pDevice->AnInfo.State = AN_STATE_UNKNOWN;
+ pDevice->AnInfo.CurrentTime_us = 0;
+
+ REG_WR(pDevice, Grc.Timer, 0);
+ for(k = 0; (pDevice->AnInfo.CurrentTime_us < 75000) &&
+ (k < 75000); k++)
+ {
+ AnStatus = Autoneg8023z(&pDevice->AnInfo);
+
+ if((AnStatus == AUTONEG_STATUS_DONE) ||
+ (AnStatus == AUTONEG_STATUS_FAILED))
+ {
+ break;
+ }
+
+ pDevice->AnInfo.CurrentTime_us = REG_RD(pDevice, Grc.Timer);
+
+ }
+ if((AnStatus == AUTONEG_STATUS_DONE) ||
+ (AnStatus == AUTONEG_STATUS_FAILED))
+ {
+ break;
+ }
+ if (j >= 1)
+ {
+ if (!(REG_RD(pDevice, MacCtrl.Status) &
+ MAC_STATUS_PCS_SYNCED)) {
+ break;
+ }
+ }
+ }
+
+ /* Stop sending configs. */
+ MM_AnTxIdle(&pDevice->AnInfo);
+
+ /* Resolve flow control settings. */
+ if((AnStatus == AUTONEG_STATUS_DONE) &&
+ pDevice->AnInfo.mr_an_complete && pDevice->AnInfo.mr_link_ok &&
+ pDevice->AnInfo.mr_lp_adv_full_duplex)
+ {
+ LM_UINT32 RemotePhyAd;
+ LM_UINT32 LocalPhyAd;
+
+ LocalPhyAd = 0;
+ if(pDevice->AnInfo.mr_adv_sym_pause)
+ {
+ LocalPhyAd |= PHY_AN_AD_PAUSE_CAPABLE;
+ }
+
+ if(pDevice->AnInfo.mr_adv_asym_pause)
+ {
+ LocalPhyAd |= PHY_AN_AD_ASYM_PAUSE;
+ }
+
+ RemotePhyAd = 0;
+ if(pDevice->AnInfo.mr_lp_adv_sym_pause)
+ {
+ RemotePhyAd |= PHY_LINK_PARTNER_PAUSE_CAPABLE;
+ }
+
+ if(pDevice->AnInfo.mr_lp_adv_asym_pause)
+ {
+ RemotePhyAd |= PHY_LINK_PARTNER_ASYM_PAUSE;
+ }
+
+ LM_SetFlowControl(pDevice, LocalPhyAd, RemotePhyAd);
+
+ CurrentLinkStatus = LM_STATUS_LINK_ACTIVE;
+ }
+ for (j = 0; j < 30; j++)
+ {
+ MM_Wait(20);
+ REG_WR(pDevice, MacCtrl.Status, MAC_STATUS_SYNC_CHANGED |
+ MAC_STATUS_CFG_CHANGED);
+ MM_Wait(20);
+ if ((REG_RD(pDevice, MacCtrl.Status) &
+ (MAC_STATUS_SYNC_CHANGED | MAC_STATUS_CFG_CHANGED)) == 0)
+ break;
+ }
+ if (pDevice->PollTbiLink)
+ {
+ Value32 = REG_RD(pDevice, MacCtrl.Status);
+ if (Value32 & MAC_STATUS_RECEIVING_CFG)
+ {
+ pDevice->IgnoreTbiLinkChange = TRUE;
+ }
+ else
+ {
+ pDevice->IgnoreTbiLinkChange = FALSE;
+ }
+ }
+ Value32 = REG_RD(pDevice, MacCtrl.Status);
+ if (CurrentLinkStatus == LM_STATUS_LINK_DOWN &&
+ (Value32 & MAC_STATUS_PCS_SYNCED) &&
+ ((Value32 & MAC_STATUS_RECEIVING_CFG) == 0))
+ {
+ CurrentLinkStatus = LM_STATUS_LINK_ACTIVE;
+ }
+ }
+ else
+ {
+ /* We are forcing line speed. */
+ pDevice->FlowControlCap &= ~LM_FLOW_CONTROL_AUTO_PAUSE;
+ LM_SetFlowControl(pDevice, 0, 0);
+
+ CurrentLinkStatus = LM_STATUS_LINK_ACTIVE;
+ REG_WR(pDevice, MacCtrl.Mode, pDevice->MacMode |
+ MAC_MODE_SEND_CONFIGS);
+ }
+ }
+ /* Set the link polarity bit. */
+ pDevice->MacMode &= ~MAC_MODE_LINK_POLARITY;
+ REG_WR(pDevice, MacCtrl.Mode, pDevice->MacMode);
+
+ pDevice->pStatusBlkVirt->Status = STATUS_BLOCK_UPDATED |
+ (pDevice->pStatusBlkVirt->Status & ~STATUS_BLOCK_LINK_CHANGED_STATUS);
+
+ for (j = 0; j < 100; j++)
+ {
+ REG_WR(pDevice, MacCtrl.Status, MAC_STATUS_SYNC_CHANGED |
+ MAC_STATUS_CFG_CHANGED);
+ MM_Wait(5);
+ if ((REG_RD(pDevice, MacCtrl.Status) &
+ (MAC_STATUS_SYNC_CHANGED | MAC_STATUS_CFG_CHANGED)) == 0)
+ break;
+ }
+
+ Value32 = REG_RD(pDevice, MacCtrl.Status);
+ if((Value32 & MAC_STATUS_PCS_SYNCED) == 0)
+ {
+ CurrentLinkStatus = LM_STATUS_LINK_DOWN;
+ if (pDevice->DisableAutoNeg == FALSE)
+ {
+ REG_WR(pDevice, MacCtrl.Mode, pDevice->MacMode |
+ MAC_MODE_SEND_CONFIGS);
+ MM_Wait(1);
+ REG_WR(pDevice, MacCtrl.Mode, pDevice->MacMode);
+ }
+ }
+
+ /* Initialize the current link status. */
+ if(CurrentLinkStatus == LM_STATUS_LINK_ACTIVE)
+ {
+ pDevice->LineSpeed = LM_LINE_SPEED_1000MBPS;
+ pDevice->DuplexMode = LM_DUPLEX_MODE_FULL;
+ REG_WR(pDevice, MacCtrl.LedCtrl, LED_CTRL_OVERRIDE_LINK_LED |
+ LED_CTRL_1000MBPS_LED_ON);
+ }
+ else
+ {
+ pDevice->LineSpeed = LM_LINE_SPEED_UNKNOWN;
+ pDevice->DuplexMode = LM_DUPLEX_MODE_UNKNOWN;
+ REG_WR(pDevice, MacCtrl.LedCtrl, LED_CTRL_OVERRIDE_LINK_LED |
+ LED_CTRL_OVERRIDE_TRAFFIC_LED);
+ }
+
+ /* Indicate link status. */
+ if (pDevice->LinkStatus != CurrentLinkStatus) {
+ pDevice->LinkStatus = CurrentLinkStatus;
+ MM_IndicateStatus(pDevice, CurrentLinkStatus);
+ }
+
+ return LM_STATUS_SUCCESS;
+}
+#endif /* INCLUDE_TBI_SUPPORT */
+
+
+/******************************************************************************/
+/* Description: */
+/* */
+/* Return: */
+/******************************************************************************/
+LM_STATUS
+LM_SetupCopperPhy(
+ PLM_DEVICE_BLOCK pDevice)
+{
+ LM_STATUS CurrentLinkStatus;
+ LM_UINT32 Value32;
+
+ /* Assume there is not link first. */
+ CurrentLinkStatus = LM_STATUS_LINK_DOWN;
+
+ /* Disable phy link change attention. */
+ REG_WR(pDevice, MacCtrl.MacEvent, 0);
+
+ /* Clear link change attention. */
+ REG_WR(pDevice, MacCtrl.Status, MAC_STATUS_SYNC_CHANGED |
+ MAC_STATUS_CFG_CHANGED);
+
+ /* Disable auto-polling for the moment. */
+ pDevice->MiMode = 0xc0000;
+ REG_WR(pDevice, MacCtrl.MiMode, pDevice->MiMode);
+ MM_Wait(40);
+
+ /* Determine the requested line speed and duplex. */
+ pDevice->OldLineSpeed = pDevice->LineSpeed;
+ LM_TranslateRequestedMediaType(pDevice->RequestedMediaType,
+ &pDevice->MediaType, &pDevice->LineSpeed, &pDevice->DuplexMode);
+
+ /* Initialize the phy chip. */
+ switch(pDevice->PhyId & PHY_ID_MASK)
+ {
+ case PHY_BCM5400_PHY_ID:
+ case PHY_BCM5401_PHY_ID:
+ case PHY_BCM5411_PHY_ID:
+ case PHY_BCM5701_PHY_ID:
+ case PHY_BCM5703_PHY_ID:
+ case PHY_BCM5704_PHY_ID:
+ CurrentLinkStatus = LM_InitBcm540xPhy(pDevice);
+ break;
+
+ default:
+ break;
+ }
+
+ if(CurrentLinkStatus == LM_STATUS_LINK_SETTING_MISMATCH)
+ {
+ CurrentLinkStatus = LM_STATUS_LINK_DOWN;
+ }
+
+ /* Setup flow control. */
+ pDevice->FlowControl = LM_FLOW_CONTROL_NONE;
+ if(CurrentLinkStatus == LM_STATUS_LINK_ACTIVE)
+ {
+ LM_FLOW_CONTROL FlowCap; /* Flow control capability. */
+
+ FlowCap = LM_FLOW_CONTROL_NONE;
+
+ if(pDevice->DuplexMode == LM_DUPLEX_MODE_FULL)
+ {
+ if(pDevice->DisableAutoNeg == FALSE ||
+ pDevice->RequestedMediaType == LM_REQUESTED_MEDIA_TYPE_AUTO ||
+ pDevice->RequestedMediaType == LM_REQUESTED_MEDIA_TYPE_UTP_AUTO)
+ {
+ LM_UINT32 ExpectedPhyAd;
+ LM_UINT32 LocalPhyAd;
+ LM_UINT32 RemotePhyAd;
+
+ LM_ReadPhy(pDevice, PHY_AN_AD_REG, &LocalPhyAd);
+ pDevice->advertising = LocalPhyAd;
+ LocalPhyAd &= (PHY_AN_AD_ASYM_PAUSE | PHY_AN_AD_PAUSE_CAPABLE);
+
+ ExpectedPhyAd = GetPhyAdFlowCntrlSettings(pDevice);
+
+ if(LocalPhyAd != ExpectedPhyAd)
+ {
+ CurrentLinkStatus = LM_STATUS_LINK_DOWN;
+ }
+ else
+ {
+ LM_ReadPhy(pDevice, PHY_LINK_PARTNER_ABILITY_REG,
+ &RemotePhyAd);
+
+ LM_SetFlowControl(pDevice, LocalPhyAd, RemotePhyAd);
+ }
+ }
+ else
+ {
+ pDevice->FlowControlCap &= ~LM_FLOW_CONTROL_AUTO_PAUSE;
+ LM_SetFlowControl(pDevice, 0, 0);
+ }
+ }
+ }
+
+ if(CurrentLinkStatus == LM_STATUS_LINK_DOWN)
+ {
+ LM_ForceAutoNeg(pDevice, pDevice->RequestedMediaType);
+
+ /* If we force line speed, we make get link right away. */
+ LM_ReadPhy(pDevice, PHY_STATUS_REG, &Value32);
+ LM_ReadPhy(pDevice, PHY_STATUS_REG, &Value32);
+ if(Value32 & PHY_STATUS_LINK_PASS)
+ {
+ CurrentLinkStatus = LM_STATUS_LINK_ACTIVE;
+ }
+ }
+
+ /* GMII interface. */
+ pDevice->MacMode &= ~MAC_MODE_PORT_MODE_MASK;
+ if(CurrentLinkStatus == LM_STATUS_LINK_ACTIVE)
+ {
+ if(pDevice->LineSpeed == LM_LINE_SPEED_100MBPS ||
+ pDevice->LineSpeed == LM_LINE_SPEED_10MBPS)
+ {
+ pDevice->MacMode |= MAC_MODE_PORT_MODE_MII;
+ }
+ else
+ {
+ pDevice->MacMode |= MAC_MODE_PORT_MODE_GMII;
+ }
+ }
+ else {
+ pDevice->MacMode |= MAC_MODE_PORT_MODE_GMII;
+ }
+
+ /* Set the MAC to operate in the appropriate duplex mode. */
+ pDevice->MacMode &= ~MAC_MODE_HALF_DUPLEX;
+ if(pDevice->DuplexMode == LM_DUPLEX_MODE_HALF)
+ {
+ pDevice->MacMode |= MAC_MODE_HALF_DUPLEX;
+ }
+
+ /* Set the link polarity bit. */
+ pDevice->MacMode &= ~MAC_MODE_LINK_POLARITY;
+ if(T3_ASIC_REV(pDevice->ChipRevId) == T3_ASIC_REV_5700)
+ {
+ if((pDevice->LedMode == LED_MODE_LINK10) ||
+ (CurrentLinkStatus == LM_STATUS_LINK_ACTIVE &&
+ pDevice->LineSpeed == LM_LINE_SPEED_10MBPS))
+ {
+ pDevice->MacMode |= MAC_MODE_LINK_POLARITY;
+ }
+ }
+ else
+ {
+ if (CurrentLinkStatus == LM_STATUS_LINK_ACTIVE)
+ {
+ pDevice->MacMode |= MAC_MODE_LINK_POLARITY;
+ }
+
+ /* Set LED mode. */
+ if(T3_ASIC_REV(pDevice->ChipRevId) == T3_ASIC_REV_5700 ||
+ T3_ASIC_REV(pDevice->ChipRevId) == T3_ASIC_REV_5701)
+ {
+ Value32 = LED_CTRL_PHY_MODE_1;
+ }
+ else
+ {
+ if(pDevice->LedMode == LED_MODE_OUTPUT)
+ {
+ Value32 = LED_CTRL_PHY_MODE_2;
+ }
+ else
+ {
+ Value32 = LED_CTRL_PHY_MODE_1;
+ }
+ }
+ REG_WR(pDevice, MacCtrl.LedCtrl, Value32);
+ }
+
+ REG_WR(pDevice, MacCtrl.Mode, pDevice->MacMode);
+
+ /* Enable auto polling. */
+ if(pDevice->PhyIntMode == T3_PHY_INT_MODE_AUTO_POLLING)
+ {
+ pDevice->MiMode |= MI_MODE_AUTO_POLLING_ENABLE;
+ REG_WR(pDevice, MacCtrl.MiMode, pDevice->MiMode);
+ }
+
+ /* Enable phy link change attention. */
+ if(pDevice->PhyIntMode == T3_PHY_INT_MODE_MI_INTERRUPT)
+ {
+ REG_WR(pDevice, MacCtrl.MacEvent, MAC_EVENT_ENABLE_MI_INTERRUPT);
+ }
+ else
+ {
+ REG_WR(pDevice, MacCtrl.MacEvent,
+ MAC_EVENT_ENABLE_LINK_STATE_CHANGED_ATTN);
+ }
+ if ((T3_ASIC_REV(pDevice->ChipRevId) == T3_ASIC_REV_5700) &&
+ (CurrentLinkStatus == LM_STATUS_LINK_ACTIVE) &&
+ (pDevice->LineSpeed == LM_LINE_SPEED_1000MBPS) &&
+ (((pDevice->PciState & T3_PCI_STATE_CONVENTIONAL_PCI_MODE) &&
+ (pDevice->PciState & T3_PCI_STATE_BUS_SPEED_HIGH)) ||
+ !(pDevice->PciState & T3_PCI_STATE_CONVENTIONAL_PCI_MODE)))
+ {
+ MM_Wait(120);
+ REG_WR(pDevice, MacCtrl.Status, MAC_STATUS_SYNC_CHANGED |
+ MAC_STATUS_CFG_CHANGED);
+ MEM_WR_OFFSET(pDevice, T3_FIRMWARE_MAILBOX,
+ T3_MAGIC_NUM_DISABLE_DMAW_ON_LINK_CHANGE);
+ }
+
+ /* Indicate link status. */
+ if (pDevice->LinkStatus != CurrentLinkStatus) {
+ pDevice->LinkStatus = CurrentLinkStatus;
+ MM_IndicateStatus(pDevice, CurrentLinkStatus);
+ }
+
+ return LM_STATUS_SUCCESS;
+} /* LM_SetupCopperPhy */
+
+/******************************************************************************/
+/* Description: */
+/* */
+/* Return: */
+/******************************************************************************/
+LM_STATUS
+LM_SetupPhy(
+ PLM_DEVICE_BLOCK pDevice)
+{
+ LM_STATUS LmStatus;
+ LM_UINT32 Value32;
+
+#if INCLUDE_TBI_SUPPORT
+ if(pDevice->EnableTbi)
+ {
+ LmStatus = LM_SetupFiberPhy(pDevice);
+ }
+ else
+#endif /* INCLUDE_TBI_SUPPORT */
+ {
+ LmStatus = LM_SetupCopperPhy(pDevice);
+ }
+ if (pDevice->ChipRevId == T3_CHIP_ID_5704_A0)
+ {
+ if (!(pDevice->PciState & T3_PCI_STATE_CONVENTIONAL_PCI_MODE))
+ {
+ Value32 = REG_RD(pDevice, PciCfg.PciState);
+ REG_WR(pDevice, PciCfg.PciState,
+ Value32 | T3_PCI_STATE_RETRY_SAME_DMA);
+ }
+ }
+ if ((pDevice->LineSpeed == LM_LINE_SPEED_1000MBPS) &&
+ (pDevice->DuplexMode == LM_DUPLEX_MODE_HALF))
+ {
+ REG_WR(pDevice, MacCtrl.TxLengths, 0x26ff);
+ }
+ else
+ {
+ REG_WR(pDevice, MacCtrl.TxLengths, 0x2620);
+ }
+
+ return LmStatus;
+}
+
+/******************************************************************************/
+/* Description: */
+/* */
+/* Return: */
+/******************************************************************************/
+LM_VOID
+LM_ReadPhy(
+PLM_DEVICE_BLOCK pDevice,
+LM_UINT32 PhyReg,
+PLM_UINT32 pData32) {
+ LM_UINT32 Value32;
+ LM_UINT32 j;
+
+ if(pDevice->PhyIntMode == T3_PHY_INT_MODE_AUTO_POLLING)
+ {
+ REG_WR(pDevice, MacCtrl.MiMode, pDevice->MiMode &
+ ~MI_MODE_AUTO_POLLING_ENABLE);
+ MM_Wait(40);
+ }
+
+ Value32 = (pDevice->PhyAddr << MI_COM_FIRST_PHY_ADDR_BIT) |
+ ((PhyReg & MI_COM_PHY_REG_ADDR_MASK) << MI_COM_FIRST_PHY_REG_ADDR_BIT) |
+ MI_COM_CMD_READ | MI_COM_START;
+
+ REG_WR(pDevice, MacCtrl.MiCom, Value32);
+
+ for(j = 0; j < 20; j++)
+ {
+ MM_Wait(25);
+
+ Value32 = REG_RD(pDevice, MacCtrl.MiCom);
+
+ if(!(Value32 & MI_COM_BUSY))
+ {
+ MM_Wait(5);
+ Value32 = REG_RD(pDevice, MacCtrl.MiCom);
+ Value32 &= MI_COM_PHY_DATA_MASK;
+ break;
+ }
+ }
+
+ if(Value32 & MI_COM_BUSY)
+ {
+ Value32 = 0;
+ }
+
+ *pData32 = Value32;
+
+ if(pDevice->PhyIntMode == T3_PHY_INT_MODE_AUTO_POLLING)
+ {
+ REG_WR(pDevice, MacCtrl.MiMode, pDevice->MiMode);
+ MM_Wait(40);
+ }
+} /* LM_ReadPhy */
+
+
+
+/******************************************************************************/
+/* Description: */
+/* */
+/* Return: */
+/******************************************************************************/
+LM_VOID
+LM_WritePhy(
+PLM_DEVICE_BLOCK pDevice,
+LM_UINT32 PhyReg,
+LM_UINT32 Data32) {
+ LM_UINT32 Value32;
+ LM_UINT32 j;
+
+ if(pDevice->PhyIntMode == T3_PHY_INT_MODE_AUTO_POLLING)
+ {
+ REG_WR(pDevice, MacCtrl.MiMode, pDevice->MiMode &
+ ~MI_MODE_AUTO_POLLING_ENABLE);
+ MM_Wait(40);
+ }
+
+ Value32 = (pDevice->PhyAddr << MI_COM_FIRST_PHY_ADDR_BIT) |
+ ((PhyReg & MI_COM_PHY_REG_ADDR_MASK) << MI_COM_FIRST_PHY_REG_ADDR_BIT) |
+ (Data32 & MI_COM_PHY_DATA_MASK) | MI_COM_CMD_WRITE | MI_COM_START;
+
+ REG_WR(pDevice, MacCtrl.MiCom, Value32);
+
+ for(j = 0; j < 20; j++)
+ {
+ MM_Wait(25);
+
+ Value32 = REG_RD(pDevice, MacCtrl.MiCom);
+
+ if(!(Value32 & MI_COM_BUSY))
+ {
+ MM_Wait(5);
+ break;
+ }
+ }
+
+ if(pDevice->PhyIntMode == T3_PHY_INT_MODE_AUTO_POLLING)
+ {
+ REG_WR(pDevice, MacCtrl.MiMode, pDevice->MiMode);
+ MM_Wait(40);
+ }
+} /* LM_WritePhy */
+
+
+/******************************************************************************/
+/* Description: */
+/* */
+/* Return: */
+/******************************************************************************/
+LM_STATUS
+LM_SetPowerState(
+PLM_DEVICE_BLOCK pDevice,
+LM_POWER_STATE PowerLevel) {
+ LM_UINT32 PmeSupport;
+ LM_UINT32 Value32;
+ LM_UINT32 PmCtrl;
+
+ /* make sureindirect accesses are enabled*/
+ MM_WriteConfig32(pDevice, T3_PCI_MISC_HOST_CTRL_REG, pDevice->MiscHostCtrl);
+
+ /* Clear the PME_ASSERT bit and the power state bits. Also enable */
+ /* the PME bit. */
+ MM_ReadConfig32(pDevice, T3_PCI_PM_STATUS_CTRL_REG, &PmCtrl);
+
+ PmCtrl |= T3_PM_PME_ASSERTED;
+ PmCtrl &= ~T3_PM_POWER_STATE_MASK;
+
+ /* Set the appropriate power state. */
+ if(PowerLevel == LM_POWER_STATE_D0)
+ {
+
+ /* Bring the card out of low power mode. */
+ PmCtrl |= T3_PM_POWER_STATE_D0;
+ MM_WriteConfig32(pDevice, T3_PCI_PM_STATUS_CTRL_REG, PmCtrl);
+
+ REG_WR(pDevice, Grc.LocalCtrl, pDevice->GrcLocalCtrl);
+ MM_Wait (40);
+#if 0 /* Bugfix by jmb...can't call WritePhy here because pDevice not fully initialized */
+ LM_WritePhy(pDevice, BCM5401_AUX_CTRL, 0x02);
+#endif
+
+ return LM_STATUS_SUCCESS;
+ }
+ else if(PowerLevel == LM_POWER_STATE_D1)
+ {
+ PmCtrl |= T3_PM_POWER_STATE_D1;
+ }
+ else if(PowerLevel == LM_POWER_STATE_D2)
+ {
+ PmCtrl |= T3_PM_POWER_STATE_D2;
+ }
+ else if(PowerLevel == LM_POWER_STATE_D3)
+ {
+ PmCtrl |= T3_PM_POWER_STATE_D3;
+ }
+ else
+ {
+ return LM_STATUS_FAILURE;
+ }
+ PmCtrl |= T3_PM_PME_ENABLE;
+
+ /* Mask out all interrupts so LM_SetupPhy won't be called while we are */
+ /* setting new line speed. */
+ Value32 = REG_RD(pDevice, PciCfg.MiscHostCtrl);
+ REG_WR(pDevice, PciCfg.MiscHostCtrl, Value32 | MISC_HOST_CTRL_MASK_PCI_INT);
+
+ if(!pDevice->RestoreOnWakeUp)
+ {
+ pDevice->RestoreOnWakeUp = TRUE;
+ pDevice->WakeUpDisableAutoNeg = pDevice->DisableAutoNeg;
+ pDevice->WakeUpRequestedMediaType = pDevice->RequestedMediaType;
+ }
+
+ /* Force auto-negotiation to 10 line speed. */
+ pDevice->DisableAutoNeg = FALSE;
+ pDevice->RequestedMediaType = LM_REQUESTED_MEDIA_TYPE_UTP_10MBPS;
+ LM_SetupPhy(pDevice);
+
+ /* Put the driver in the initial state, and go through the power down */
+ /* sequence. */
+ LM_Halt(pDevice);
+
+ MM_ReadConfig32(pDevice, T3_PCI_PM_CAP_REG, &PmeSupport);
+
+ if (pDevice->WakeUpModeCap != LM_WAKE_UP_MODE_NONE)
+ {
+
+ /* Enable WOL. */
+ LM_WritePhy(pDevice, BCM5401_AUX_CTRL, 0x5a);
+ MM_Wait(40);
+
+ /* Set LED mode. */
+ if(T3_ASIC_REV(pDevice->ChipRevId) == T3_ASIC_REV_5700 ||
+ T3_ASIC_REV(pDevice->ChipRevId) == T3_ASIC_REV_5701)
+ {
+ Value32 = LED_CTRL_PHY_MODE_1;
+ }
+ else
+ {
+ if(pDevice->LedMode == LED_MODE_OUTPUT)
+ {
+ Value32 = LED_CTRL_PHY_MODE_2;
+ }
+ else
+ {
+ Value32 = LED_CTRL_PHY_MODE_1;
+ }
+ }
+
+ Value32 = MAC_MODE_PORT_MODE_MII;
+ if(T3_ASIC_REV(pDevice->ChipRevId) == T3_ASIC_REV_5700)
+ {
+ if(pDevice->LedMode == LED_MODE_LINK10 ||
+ pDevice->WolSpeed == WOL_SPEED_10MB)
+ {
+ Value32 |= MAC_MODE_LINK_POLARITY;
+ }
+ }
+ else
+ {
+ Value32 |= MAC_MODE_LINK_POLARITY;
+ }
+ REG_WR(pDevice, MacCtrl.Mode, Value32);
+ MM_Wait(40); MM_Wait(40); MM_Wait(40);
+
+ /* Always enable magic packet wake-up if we have vaux. */
+ if((PmeSupport & T3_PCI_PM_CAP_PME_D3COLD) &&
+ (pDevice->WakeUpModeCap & LM_WAKE_UP_MODE_MAGIC_PACKET))
+ {
+ Value32 |= MAC_MODE_DETECT_MAGIC_PACKET_ENABLE;
+ }
+
+ REG_WR(pDevice, MacCtrl.Mode, Value32);
+
+ /* Enable the receiver. */
+ REG_WR(pDevice, MacCtrl.RxMode, RX_MODE_ENABLE);
+ }
+
+ /* Disable tx/rx clocks, and seletect an alternate clock. */
+ if(pDevice->WolSpeed == WOL_SPEED_100MB)
+ {
+ if(T3_ASIC_REV(pDevice->ChipRevId) == T3_ASIC_REV_5700 ||
+ T3_ASIC_REV(pDevice->ChipRevId) == T3_ASIC_REV_5701)
+ {
+ Value32 = T3_PCI_DISABLE_RX_CLOCK | T3_PCI_DISABLE_TX_CLOCK |
+ T3_PCI_SELECT_ALTERNATE_CLOCK;
+ }
+ else
+ {
+ Value32 = T3_PCI_SELECT_ALTERNATE_CLOCK;
+ }
+ REG_WR(pDevice, PciCfg.ClockCtrl, Value32);
+
+ MM_Wait(40);
+
+ if(T3_ASIC_REV(pDevice->ChipRevId) == T3_ASIC_REV_5700 ||
+ T3_ASIC_REV(pDevice->ChipRevId) == T3_ASIC_REV_5701)
+ {
+ Value32 = T3_PCI_DISABLE_RX_CLOCK | T3_PCI_DISABLE_TX_CLOCK |
+ T3_PCI_SELECT_ALTERNATE_CLOCK | T3_PCI_44MHZ_CORE_CLOCK;
+ }
+ else
+ {
+ Value32 = T3_PCI_SELECT_ALTERNATE_CLOCK |
+ T3_PCI_44MHZ_CORE_CLOCK;
+ }
+
+ REG_WR(pDevice, PciCfg.ClockCtrl, Value32);
+
+ MM_Wait(40);
+
+ if(T3_ASIC_REV(pDevice->ChipRevId) == T3_ASIC_REV_5700 ||
+ T3_ASIC_REV(pDevice->ChipRevId) == T3_ASIC_REV_5701)
+ {
+ Value32 = T3_PCI_DISABLE_RX_CLOCK | T3_PCI_DISABLE_TX_CLOCK |
+ T3_PCI_44MHZ_CORE_CLOCK;
+ }
+ else
+ {
+ Value32 = T3_PCI_44MHZ_CORE_CLOCK;
+ }
+
+ REG_WR(pDevice, PciCfg.ClockCtrl, Value32);
+ }
+ else
+ {
+ if(T3_ASIC_REV(pDevice->ChipRevId) == T3_ASIC_REV_5700 ||
+ T3_ASIC_REV(pDevice->ChipRevId) == T3_ASIC_REV_5701)
+ {
+ Value32 = T3_PCI_DISABLE_RX_CLOCK | T3_PCI_DISABLE_TX_CLOCK |
+ T3_PCI_SELECT_ALTERNATE_CLOCK |
+ T3_PCI_POWER_DOWN_PCI_PLL133;
+ }
+ else
+ {
+ Value32 = T3_PCI_SELECT_ALTERNATE_CLOCK |
+ T3_PCI_POWER_DOWN_PCI_PLL133;
+ }
+
+ REG_WR(pDevice, PciCfg.ClockCtrl, Value32);
+ }
+
+ MM_Wait(40);
+
+ if(!pDevice->EepromWp && (pDevice->WakeUpModeCap != LM_WAKE_UP_MODE_NONE))
+ {
+ /* Switch adapter to auxilliary power. */
+ if(T3_ASIC_REV(pDevice->ChipRevId) == T3_ASIC_REV_5700 ||
+ T3_ASIC_REV(pDevice->ChipRevId) == T3_ASIC_REV_5701)
+ {
+ /* GPIO0 = 1, GPIO1 = 1, GPIO2 = 0. */
+ REG_WR(pDevice, Grc.LocalCtrl, pDevice->GrcLocalCtrl |
+ GRC_MISC_LOCAL_CTRL_GPIO_OE0 |
+ GRC_MISC_LOCAL_CTRL_GPIO_OE1 |
+ GRC_MISC_LOCAL_CTRL_GPIO_OE2 |
+ GRC_MISC_LOCAL_CTRL_GPIO_OUTPUT0 |
+ GRC_MISC_LOCAL_CTRL_GPIO_OUTPUT1);
+ MM_Wait(40);
+ }
+ else
+ {
+ /* GPIO0 = 0, GPIO1 = 1, GPIO2 = 1. */
+ REG_WR(pDevice, Grc.LocalCtrl, pDevice->GrcLocalCtrl |
+ GRC_MISC_LOCAL_CTRL_GPIO_OE0 |
+ GRC_MISC_LOCAL_CTRL_GPIO_OE1 |
+ GRC_MISC_LOCAL_CTRL_GPIO_OE2 |
+ GRC_MISC_LOCAL_CTRL_GPIO_OUTPUT1 |
+ GRC_MISC_LOCAL_CTRL_GPIO_OUTPUT2);
+ MM_Wait(40);
+
+ /* GPIO0 = 1, GPIO1 = 1, GPIO2 = 1. */
+ REG_WR(pDevice, Grc.LocalCtrl, pDevice->GrcLocalCtrl |
+ GRC_MISC_LOCAL_CTRL_GPIO_OE0 |
+ GRC_MISC_LOCAL_CTRL_GPIO_OE1 |
+ GRC_MISC_LOCAL_CTRL_GPIO_OE2 |
+ GRC_MISC_LOCAL_CTRL_GPIO_OUTPUT0 |
+ GRC_MISC_LOCAL_CTRL_GPIO_OUTPUT1 |
+ GRC_MISC_LOCAL_CTRL_GPIO_OUTPUT2);
+ MM_Wait(40);
+
+ /* GPIO0 = 1, GPIO1 = 1, GPIO2 = 0. */
+ REG_WR(pDevice, Grc.LocalCtrl, pDevice->GrcLocalCtrl |
+ GRC_MISC_LOCAL_CTRL_GPIO_OE0 |
+ GRC_MISC_LOCAL_CTRL_GPIO_OE1 |
+ GRC_MISC_LOCAL_CTRL_GPIO_OE2 |
+ GRC_MISC_LOCAL_CTRL_GPIO_OUTPUT0 |
+ GRC_MISC_LOCAL_CTRL_GPIO_OUTPUT1);
+ MM_Wait(40);
+ }
+ }
+
+ /* Set the phy to low power mode. */
+ /* Put the the hardware in low power mode. */
+ MM_WriteConfig32(pDevice, T3_PCI_PM_STATUS_CTRL_REG, PmCtrl);
+
+ return LM_STATUS_SUCCESS;
+} /* LM_SetPowerState */
+
+
+
+/******************************************************************************/
+/* Description: */
+/* */
+/* Return: */
+/******************************************************************************/
+static LM_UINT32
+GetPhyAdFlowCntrlSettings(
+ PLM_DEVICE_BLOCK pDevice)
+{
+ LM_UINT32 Value32;
+
+ Value32 = 0;
+
+ /* Auto negotiation flow control only when autonegotiation is enabled. */
+ if(pDevice->DisableAutoNeg == FALSE ||
+ pDevice->RequestedMediaType == LM_REQUESTED_MEDIA_TYPE_AUTO ||
+ pDevice->RequestedMediaType == LM_REQUESTED_MEDIA_TYPE_UTP_AUTO)
+ {
+ /* Please refer to Table 28B-3 of the 802.3ab-1999 spec. */
+ if((pDevice->FlowControlCap == LM_FLOW_CONTROL_AUTO_PAUSE) ||
+ ((pDevice->FlowControlCap & LM_FLOW_CONTROL_RECEIVE_PAUSE) &&
+ (pDevice->FlowControlCap & LM_FLOW_CONTROL_TRANSMIT_PAUSE)))
+ {
+ Value32 |= PHY_AN_AD_PAUSE_CAPABLE;
+ }
+ else if(pDevice->FlowControlCap & LM_FLOW_CONTROL_TRANSMIT_PAUSE)
+ {
+ Value32 |= PHY_AN_AD_ASYM_PAUSE;
+ }
+ else if(pDevice->FlowControlCap & LM_FLOW_CONTROL_RECEIVE_PAUSE)
+ {
+ Value32 |= PHY_AN_AD_PAUSE_CAPABLE | PHY_AN_AD_ASYM_PAUSE;
+ }
+ }
+
+ return Value32;
+}
+
+
+
+/******************************************************************************/
+/* Description: */
+/* */
+/* Return: */
+/* LM_STATUS_FAILURE */
+/* LM_STATUS_SUCCESS */
+/* */
+/******************************************************************************/
+static LM_STATUS
+LM_ForceAutoNegBcm540xPhy(
+PLM_DEVICE_BLOCK pDevice,
+LM_REQUESTED_MEDIA_TYPE RequestedMediaType)
+{
+ LM_MEDIA_TYPE MediaType;
+ LM_LINE_SPEED LineSpeed;
+ LM_DUPLEX_MODE DuplexMode;
+ LM_UINT32 NewPhyCtrl;
+ LM_UINT32 Value32;
+ LM_UINT32 Cnt;
+
+ /* Get the interface type, line speed, and duplex mode. */
+ LM_TranslateRequestedMediaType(RequestedMediaType, &MediaType, &LineSpeed,
+ &DuplexMode);
+
+ if (pDevice->RestoreOnWakeUp)
+ {
+ LM_WritePhy(pDevice, BCM540X_1000BASET_CTRL_REG, 0);
+ pDevice->advertising1000 = 0;
+ Value32 = PHY_AN_AD_10BASET_FULL | PHY_AN_AD_10BASET_HALF;
+ if (pDevice->WolSpeed == WOL_SPEED_100MB)
+ {
+ Value32 |= PHY_AN_AD_100BASETX_FULL | PHY_AN_AD_100BASETX_HALF;
+ }
+ Value32 |= PHY_AN_AD_PROTOCOL_802_3_CSMA_CD;
+ Value32 |= GetPhyAdFlowCntrlSettings(pDevice);
+ LM_WritePhy(pDevice, PHY_AN_AD_REG, Value32);
+ pDevice->advertising = Value32;
+ }
+ /* Setup the auto-negotiation advertisement register. */
+ else if(LineSpeed == LM_LINE_SPEED_UNKNOWN)
+ {
+ /* Setup the 10/100 Mbps auto-negotiation advertisement register. */
+ Value32 = PHY_AN_AD_PROTOCOL_802_3_CSMA_CD |
+ PHY_AN_AD_10BASET_HALF | PHY_AN_AD_10BASET_FULL |
+ PHY_AN_AD_100BASETX_FULL | PHY_AN_AD_100BASETX_HALF;
+ Value32 |= GetPhyAdFlowCntrlSettings(pDevice);
+
+ LM_WritePhy(pDevice, PHY_AN_AD_REG, Value32);
+ pDevice->advertising = Value32;
+
+ /* Advertise 1000Mbps */
+ Value32 = BCM540X_AN_AD_1000BASET_HALF | BCM540X_AN_AD_1000BASET_FULL;
+
+#if INCLUDE_5701_AX_FIX
+ /* Bug: workaround for CRC error in gigabit mode when we are in */
+ /* slave mode. This will force the PHY to operate in */
+ /* master mode. */
+ if(pDevice->ChipRevId == T3_CHIP_ID_5701_A0 ||
+ pDevice->ChipRevId == T3_CHIP_ID_5701_B0)
+ {
+ Value32 |= BCM540X_CONFIG_AS_MASTER |
+ BCM540X_ENABLE_CONFIG_AS_MASTER;
+ }
+#endif
+
+ LM_WritePhy(pDevice, BCM540X_1000BASET_CTRL_REG, Value32);
+ pDevice->advertising1000 = Value32;
+ }
+ else
+ {
+ if(LineSpeed == LM_LINE_SPEED_1000MBPS)
+ {
+ Value32 = PHY_AN_AD_PROTOCOL_802_3_CSMA_CD;
+ Value32 |= GetPhyAdFlowCntrlSettings(pDevice);
+
+ LM_WritePhy(pDevice, PHY_AN_AD_REG, Value32);
+ pDevice->advertising = Value32;
+
+ if(DuplexMode != LM_DUPLEX_MODE_FULL)
+ {
+ Value32 = BCM540X_AN_AD_1000BASET_HALF;
+ }
+ else
+ {
+ Value32 = BCM540X_AN_AD_1000BASET_FULL;
+ }
+
+ LM_WritePhy(pDevice, BCM540X_1000BASET_CTRL_REG, Value32);
+ pDevice->advertising1000 = Value32;
+ }
+ else if(LineSpeed == LM_LINE_SPEED_100MBPS)
+ {
+ LM_WritePhy(pDevice, BCM540X_1000BASET_CTRL_REG, 0);
+ pDevice->advertising1000 = 0;
+
+ if(DuplexMode != LM_DUPLEX_MODE_FULL)
+ {
+ Value32 = PHY_AN_AD_100BASETX_HALF;
+ }
+ else
+ {
+ Value32 = PHY_AN_AD_100BASETX_FULL;
+ }
+
+ Value32 |= PHY_AN_AD_PROTOCOL_802_3_CSMA_CD;
+ Value32 |= GetPhyAdFlowCntrlSettings(pDevice);
+
+ LM_WritePhy(pDevice, PHY_AN_AD_REG, Value32);
+ pDevice->advertising = Value32;
+ }
+ else if(LineSpeed == LM_LINE_SPEED_10MBPS)
+ {
+ LM_WritePhy(pDevice, BCM540X_1000BASET_CTRL_REG, 0);
+ pDevice->advertising1000 = 0;
+
+ if(DuplexMode != LM_DUPLEX_MODE_FULL)
+ {
+ Value32 = PHY_AN_AD_10BASET_HALF;
+ }
+ else
+ {
+ Value32 = PHY_AN_AD_10BASET_FULL;
+ }
+
+ Value32 |= PHY_AN_AD_PROTOCOL_802_3_CSMA_CD;
+ Value32 |= GetPhyAdFlowCntrlSettings(pDevice);
+
+ LM_WritePhy(pDevice, PHY_AN_AD_REG, Value32);
+ pDevice->advertising = Value32;
+ }
+ }
+
+ /* Force line speed if auto-negotiation is disabled. */
+ if(pDevice->DisableAutoNeg && LineSpeed != LM_LINE_SPEED_UNKNOWN)
+ {
+ /* This code path is executed only when there is link. */
+ pDevice->MediaType = MediaType;
+ pDevice->LineSpeed = LineSpeed;
+ pDevice->DuplexMode = DuplexMode;
+
+ /* Force line seepd. */
+ NewPhyCtrl = 0;
+ switch(LineSpeed)
+ {
+ case LM_LINE_SPEED_10MBPS:
+ NewPhyCtrl |= PHY_CTRL_SPEED_SELECT_10MBPS;
+ break;
+ case LM_LINE_SPEED_100MBPS:
+ NewPhyCtrl |= PHY_CTRL_SPEED_SELECT_100MBPS;
+ break;
+ case LM_LINE_SPEED_1000MBPS:
+ NewPhyCtrl |= PHY_CTRL_SPEED_SELECT_1000MBPS;
+ break;
+ default:
+ NewPhyCtrl |= PHY_CTRL_SPEED_SELECT_1000MBPS;
+ break;
+ }
+
+ if(DuplexMode == LM_DUPLEX_MODE_FULL)
+ {
+ NewPhyCtrl |= PHY_CTRL_FULL_DUPLEX_MODE;
+ }
+
+ /* Don't do anything if the PHY_CTRL is already what we wanted. */
+ LM_ReadPhy(pDevice, PHY_CTRL_REG, &Value32);
+ if(Value32 != NewPhyCtrl)
+ {
+ /* Temporary bring the link down before forcing line speed. */
+ LM_WritePhy(pDevice, PHY_CTRL_REG, PHY_CTRL_LOOPBACK_MODE);
+
+ /* Wait for link to go down. */
+ for(Cnt = 0; Cnt < 15000; Cnt++)
+ {
+ MM_Wait(10);
+
+ LM_ReadPhy(pDevice, PHY_STATUS_REG, &Value32);
+ LM_ReadPhy(pDevice, PHY_STATUS_REG, &Value32);
+
+ if(!(Value32 & PHY_STATUS_LINK_PASS))
+ {
+ MM_Wait(40);
+ break;
+ }
+ }
+
+ LM_WritePhy(pDevice, PHY_CTRL_REG, NewPhyCtrl);
+ MM_Wait(40);
+ }
+ }
+ else
+ {
+ LM_WritePhy(pDevice, PHY_CTRL_REG, PHY_CTRL_AUTO_NEG_ENABLE |
+ PHY_CTRL_RESTART_AUTO_NEG);
+ }
+
+ return LM_STATUS_SUCCESS;
+} /* LM_ForceAutoNegBcm540xPhy */
+
+
+
+/******************************************************************************/
+/* Description: */
+/* */
+/* Return: */
+/******************************************************************************/
+static LM_STATUS
+LM_ForceAutoNeg(
+PLM_DEVICE_BLOCK pDevice,
+LM_REQUESTED_MEDIA_TYPE RequestedMediaType)
+{
+ LM_STATUS LmStatus;
+
+ /* Initialize the phy chip. */
+ switch(pDevice->PhyId & PHY_ID_MASK)
+ {
+ case PHY_BCM5400_PHY_ID:
+ case PHY_BCM5401_PHY_ID:
+ case PHY_BCM5411_PHY_ID:
+ case PHY_BCM5701_PHY_ID:
+ case PHY_BCM5703_PHY_ID:
+ case PHY_BCM5704_PHY_ID:
+ LmStatus = LM_ForceAutoNegBcm540xPhy(pDevice, RequestedMediaType);
+ break;
+
+ default:
+ LmStatus = LM_STATUS_FAILURE;
+ break;
+ }
+
+ return LmStatus;
+} /* LM_ForceAutoNeg */
+
+/******************************************************************************/
+/* Description: */
+/* */
+/* Return: */
+/******************************************************************************/
+LM_STATUS LM_LoadFirmware(PLM_DEVICE_BLOCK pDevice,
+ PT3_FWIMG_INFO pFwImg,
+ LM_UINT32 LoadCpu,
+ LM_UINT32 StartCpu)
+{
+ LM_UINT32 i;
+ LM_UINT32 address;
+
+ if (LoadCpu & T3_RX_CPU_ID)
+ {
+ if (LM_HaltCpu(pDevice,T3_RX_CPU_ID) != LM_STATUS_SUCCESS)
+ {
+ return LM_STATUS_FAILURE;
+ }
+
+ /* First of all clear scrach pad memory */
+ for (i = 0; i < T3_RX_CPU_SPAD_SIZE; i+=4)
+ {
+ LM_RegWrInd(pDevice,T3_RX_CPU_SPAD_ADDR+i,0);
+ }
+
+ /* Copy code first */
+ address = T3_RX_CPU_SPAD_ADDR + (pFwImg->Text.Offset & 0xffff);
+ for (i = 0; i <= pFwImg->Text.Length; i+=4)
+ {
+ LM_RegWrInd(pDevice,address+i,
+ ((LM_UINT32 *)pFwImg->Text.Buffer)[i/4]);
+ }
+
+ address = T3_RX_CPU_SPAD_ADDR + (pFwImg->ROnlyData.Offset & 0xffff);
+ for (i = 0; i <= pFwImg->ROnlyData.Length; i+=4)
+ {
+ LM_RegWrInd(pDevice,address+i,
+ ((LM_UINT32 *)pFwImg->ROnlyData.Buffer)[i/4]);
+ }
+
+ address = T3_RX_CPU_SPAD_ADDR + (pFwImg->Data.Offset & 0xffff);
+ for (i= 0; i <= pFwImg->Data.Length; i+=4)
+ {
+ LM_RegWrInd(pDevice,address+i,
+ ((LM_UINT32 *)pFwImg->Data.Buffer)[i/4]);
+ }
+ }
+
+ if (LoadCpu & T3_TX_CPU_ID)
+ {
+ if (LM_HaltCpu(pDevice,T3_TX_CPU_ID) != LM_STATUS_SUCCESS)
+ {
+ return LM_STATUS_FAILURE;
+ }
+
+ /* First of all clear scrach pad memory */
+ for (i = 0; i < T3_TX_CPU_SPAD_SIZE; i+=4)
+ {
+ LM_RegWrInd(pDevice,T3_TX_CPU_SPAD_ADDR+i,0);
+ }
+
+ /* Copy code first */
+ address = T3_TX_CPU_SPAD_ADDR + (pFwImg->Text.Offset & 0xffff);
+ for (i= 0; i <= pFwImg->Text.Length; i+=4)
+ {
+ LM_RegWrInd(pDevice,address+i,
+ ((LM_UINT32 *)pFwImg->Text.Buffer)[i/4]);
+ }
+
+ address = T3_TX_CPU_SPAD_ADDR + (pFwImg->ROnlyData.Offset & 0xffff);
+ for (i= 0; i <= pFwImg->ROnlyData.Length; i+=4)
+ {
+ LM_RegWrInd(pDevice,address+i,
+ ((LM_UINT32 *)pFwImg->ROnlyData.Buffer)[i/4]);
+ }
+
+ address = T3_TX_CPU_SPAD_ADDR + (pFwImg->Data.Offset & 0xffff);
+ for (i= 0; i <= pFwImg->Data.Length; i+=4)
+ {
+ LM_RegWrInd(pDevice,address+i,
+ ((LM_UINT32 *)pFwImg->Data.Buffer)[i/4]);
+ }
+ }
+
+ if (StartCpu & T3_RX_CPU_ID)
+ {
+ /* Start Rx CPU */
+ REG_WR(pDevice,rxCpu.reg.state, 0xffffffff);
+ REG_WR(pDevice,rxCpu.reg.PC,pFwImg->StartAddress);
+ for (i = 0 ; i < 5; i++)
+ {
+ if (pFwImg->StartAddress == REG_RD(pDevice,rxCpu.reg.PC))
+ break;
+
+ REG_WR(pDevice,rxCpu.reg.state, 0xffffffff);
+ REG_WR(pDevice,rxCpu.reg.mode,CPU_MODE_HALT);
+ REG_WR(pDevice,rxCpu.reg.PC,pFwImg->StartAddress);
+ MM_Wait(1000);
+ }
+
+ REG_WR(pDevice,rxCpu.reg.state, 0xffffffff);
+ REG_WR(pDevice,rxCpu.reg.mode, 0);
+ }
+
+ if (StartCpu & T3_TX_CPU_ID)
+ {
+ /* Start Tx CPU */
+ REG_WR(pDevice,txCpu.reg.state, 0xffffffff);
+ REG_WR(pDevice,txCpu.reg.PC,pFwImg->StartAddress);
+ for (i = 0 ; i < 5; i++)
+ {
+ if (pFwImg->StartAddress == REG_RD(pDevice,txCpu.reg.PC))
+ break;
+
+ REG_WR(pDevice,txCpu.reg.state, 0xffffffff);
+ REG_WR(pDevice,txCpu.reg.mode,CPU_MODE_HALT);
+ REG_WR(pDevice,txCpu.reg.PC,pFwImg->StartAddress);
+ MM_Wait(1000);
+ }
+
+ REG_WR(pDevice,txCpu.reg.state, 0xffffffff);
+ REG_WR(pDevice,txCpu.reg.mode, 0);
+ }
+
+ return LM_STATUS_SUCCESS;
+}
+
+STATIC LM_STATUS LM_HaltCpu(PLM_DEVICE_BLOCK pDevice,LM_UINT32 cpu_number)
+{
+ LM_UINT32 i;
+
+ if (cpu_number == T3_RX_CPU_ID)
+ {
+ for (i = 0 ; i < 10000; i++)
+ {
+ REG_WR(pDevice,rxCpu.reg.state, 0xffffffff);
+ REG_WR(pDevice,rxCpu.reg.mode,CPU_MODE_HALT);
+
+ if (REG_RD(pDevice,rxCpu.reg.mode) & CPU_MODE_HALT)
+ break;
+ }
+
+ REG_WR(pDevice,rxCpu.reg.state, 0xffffffff);
+ REG_WR(pDevice,rxCpu.reg.mode,CPU_MODE_HALT);
+ MM_Wait(10);
+ }
+ else
+ {
+ for (i = 0 ; i < 10000; i++)
+ {
+ REG_WR(pDevice,txCpu.reg.state, 0xffffffff);
+ REG_WR(pDevice,txCpu.reg.mode,CPU_MODE_HALT);
+
+ if (REG_RD(pDevice,txCpu.reg.mode) & CPU_MODE_HALT)
+ break;
+ }
+ }
+
+ return (( i == 10000) ? LM_STATUS_FAILURE : LM_STATUS_SUCCESS);
+}
+
+
+int
+LM_BlinkLED(PLM_DEVICE_BLOCK pDevice, LM_UINT32 BlinkDurationSec)
+{
+ LM_UINT32 Oldcfg;
+ int j;
+ int ret = 0;
+
+ if(BlinkDurationSec == 0)
+ {
+ return 0;
+ }
+ if(BlinkDurationSec > 120)
+ {
+ BlinkDurationSec = 120;
+ }
+
+ Oldcfg = REG_RD(pDevice, MacCtrl.LedCtrl);
+ for(j = 0; j < BlinkDurationSec * 2; j++)
+ {
+ if(j % 2)
+ {
+ /* Turn on the LEDs. */
+ REG_WR(pDevice, MacCtrl.LedCtrl,
+ LED_CTRL_OVERRIDE_LINK_LED |
+ LED_CTRL_1000MBPS_LED_ON |
+ LED_CTRL_100MBPS_LED_ON |
+ LED_CTRL_10MBPS_LED_ON |
+ LED_CTRL_OVERRIDE_TRAFFIC_LED |
+ LED_CTRL_BLINK_TRAFFIC_LED |
+ LED_CTRL_TRAFFIC_LED);
+ }
+ else
+ {
+ /* Turn off the LEDs. */
+ REG_WR(pDevice, MacCtrl.LedCtrl,
+ LED_CTRL_OVERRIDE_LINK_LED |
+ LED_CTRL_OVERRIDE_TRAFFIC_LED);
+ }
+
+#ifndef EMBEDDED
+ current->state = TASK_INTERRUPTIBLE;
+ if (schedule_timeout(HZ/2) != 0) {
+ ret = -EINTR;
+ break;
+ }
+#else
+ udelay(100000); /* 1s sleep */
+#endif
+ }
+ REG_WR(pDevice, MacCtrl.LedCtrl, Oldcfg);
+ return ret;
+}
+
+int t3_do_dma(PLM_DEVICE_BLOCK pDevice,
+ LM_PHYSICAL_ADDRESS host_addr_phy, int length,
+ int dma_read)
+{
+ T3_DMA_DESC dma_desc;
+ int i;
+ LM_UINT32 dma_desc_addr;
+ LM_UINT32 value32;
+
+ REG_WR(pDevice, BufMgr.Mode, 0);
+ REG_WR(pDevice, Ftq.Reset, 0);
+
+ dma_desc.host_addr.High = host_addr_phy.High;
+ dma_desc.host_addr.Low = host_addr_phy.Low;
+ dma_desc.nic_mbuf = 0x2100;
+ dma_desc.len = length;
+ dma_desc.flags = 0x00000004; /* Generate Rx-CPU event */
+
+ if (dma_read)
+ {
+ dma_desc.cqid_sqid = (T3_QID_RX_BD_COMP << 8) |
+ T3_QID_DMA_HIGH_PRI_READ;
+ REG_WR(pDevice, DmaRead.Mode, DMA_READ_MODE_ENABLE);
+ }
+ else
+ {
+ dma_desc.cqid_sqid = (T3_QID_RX_DATA_COMP << 8) |
+ T3_QID_DMA_HIGH_PRI_WRITE;
+ REG_WR(pDevice, DmaWrite.Mode, DMA_WRITE_MODE_ENABLE);
+ }
+
+ dma_desc_addr = T3_NIC_DMA_DESC_POOL_ADDR;
+
+ /* Writing this DMA descriptor to DMA memory */
+ for (i = 0; i < sizeof(T3_DMA_DESC); i += 4)
+ {
+ value32 = *((PLM_UINT32) (((PLM_UINT8) &dma_desc) + i));
+ MM_WriteConfig32(pDevice, T3_PCI_MEM_WIN_ADDR_REG, dma_desc_addr+i);
+ MM_WriteConfig32(pDevice, T3_PCI_MEM_WIN_DATA_REG, cpu_to_le32(value32));
+ }
+ MM_WriteConfig32(pDevice, T3_PCI_MEM_WIN_ADDR_REG, 0);
+
+ if (dma_read)
+ REG_WR(pDevice, Ftq.DmaHighReadFtqFifoEnqueueDequeue, dma_desc_addr);
+ else
+ REG_WR(pDevice, Ftq.DmaHighWriteFtqFifoEnqueueDequeue, dma_desc_addr);
+
+ for (i = 0; i < 40; i++)
+ {
+ if (dma_read)
+ value32 = REG_RD(pDevice, Ftq.RcvBdCompFtqFifoEnqueueDequeue);
+ else
+ value32 = REG_RD(pDevice, Ftq.RcvDataCompFtqFifoEnqueueDequeue);
+
+ if ((value32 & 0xffff) == dma_desc_addr)
+ break;
+
+ MM_Wait(10);
+ }
+
+ return LM_STATUS_SUCCESS;
+}
+
+STATIC LM_STATUS
+LM_DmaTest(PLM_DEVICE_BLOCK pDevice, PLM_UINT8 pBufferVirt,
+ LM_PHYSICAL_ADDRESS BufferPhy, LM_UINT32 BufferSize)
+{
+ int j;
+ LM_UINT32 *ptr;
+ int dma_success = 0;
+
+ if(T3_ASIC_REV(pDevice->ChipRevId) != T3_ASIC_REV_5700 &&
+ T3_ASIC_REV(pDevice->ChipRevId) != T3_ASIC_REV_5701)
+ {
+ return LM_STATUS_SUCCESS;
+ }
+ while (!dma_success)
+ {
+ /* Fill data with incremental patterns */
+ ptr = (LM_UINT32 *)pBufferVirt;
+ for (j = 0; j < BufferSize/4; j++)
+ *ptr++ = j;
+
+ if (t3_do_dma(pDevice,BufferPhy,BufferSize, 1) == LM_STATUS_FAILURE)
+ {
+ return LM_STATUS_FAILURE;
+ }
+
+ MM_Wait(40);
+ ptr = (LM_UINT32 *)pBufferVirt;
+ /* Fill data with zero */
+ for (j = 0; j < BufferSize/4; j++)
+ *ptr++ = 0;
+
+ if (t3_do_dma(pDevice,BufferPhy,BufferSize, 0) == LM_STATUS_FAILURE)
+ {
+ return LM_STATUS_FAILURE;
+ }
+
+ MM_Wait(40);
+ /* Check for data */
+ ptr = (LM_UINT32 *)pBufferVirt;
+ for (j = 0; j < BufferSize/4; j++)
+ {
+ if (*ptr++ != j)
+ {
+ if ((pDevice->DmaReadWriteCtrl & DMA_CTRL_WRITE_BOUNDARY_MASK)
+ == DMA_CTRL_WRITE_BOUNDARY_DISABLE)
+ {
+ pDevice->DmaReadWriteCtrl = (pDevice->DmaReadWriteCtrl &
+ ~DMA_CTRL_WRITE_BOUNDARY_MASK) |
+ DMA_CTRL_WRITE_BOUNDARY_16;
+ REG_WR(pDevice, PciCfg.DmaReadWriteCtrl,
+ pDevice->DmaReadWriteCtrl);
+ break;
+ }
+ else
+ {
+ return LM_STATUS_FAILURE;
+ }
+ }
+ }
+ if (j == (BufferSize/4))
+ dma_success = 1;
+ }
+ return LM_STATUS_SUCCESS;
+}
+#endif /* CFG_CMD_NET, !CONFIG_NET_MULTI, CONFIG_TIGON3 */