diff --git a/include/configs/xpedite520x.h b/include/configs/xpedite520x.h
new file mode 100644
index 0000000..fc15d8e
--- /dev/null
+++ b/include/configs/xpedite520x.h
@@ -0,0 +1,544 @@
+/*
+ * Copyright 2008 Extreme Engineering Solutions, Inc.
+ * Copyright 2004-2008 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * xpedite520x board configuration file
+ */
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ */
+#define CONFIG_BOOKE		1	/* BOOKE */
+#define CONFIG_E500		1	/* BOOKE e500 family */
+#define CONFIG_MPC85xx		1	/* MPC8540/60/55/41/48 */
+#define CONFIG_MPC8548		1
+#define CONFIG_XPEDITE5200	1
+#define CONFIG_SYS_BOARD_NAME	"XPedite5200"
+#define CONFIG_SYS_FORM_PMC_XMC	1
+#define CONFIG_BOARD_EARLY_INIT_R	/* Call board_pre_init */
+
+#ifndef CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_TEXT_BASE	0xfff80000
+#endif
+
+#define CONFIG_PCI		1	/* Enable PCI/PCIE */
+#define CONFIG_PCI_PNP		1	/* do pci plug-and-play */
+#define CONFIG_PCI_SCAN_SHOW	1	/* show pci devices on startup */
+#define CONFIG_PCI1		1	/* PCI controller 1 */
+#define CONFIG_FSL_PCI_INIT	1	/* Use common FSL init code */
+#define CONFIG_SYS_PCI_64BIT	1	/* enable 64-bit PCI resources */
+#define CONFIG_FSL_LAW		1	/* Use common FSL init code */
+
+/*
+ * DDR config
+ */
+#define CONFIG_FSL_DDR2
+#undef CONFIG_FSL_DDR_INTERACTIVE
+#define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup */
+#define CONFIG_DDR_SPD
+#define CONFIG_MEM_INIT_VALUE		0xdeadbeef
+#define SPD_EEPROM_ADDRESS		0x54
+#define CONFIG_NUM_DDR_CONTROLLERS	1
+#define CONFIG_DIMM_SLOTS_PER_CTLR	1
+#define CONFIG_CHIP_SELECTS_PER_CTRL	2
+#define CONFIG_DDR_ECC
+#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
+#define CONFIG_SYS_DDR_SDRAM_BASE	0x00000000
+#define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE
+#define CONFIG_VERY_BIG_RAM
+
+#define CONFIG_SYS_CLK_FREQ	66666666
+
+/*
+ * These can be toggled for performance analysis, otherwise use default.
+ */
+#define CONFIG_L2_CACHE			/* toggle L2 cache */
+#define CONFIG_BTB			/* toggle branch predition */
+#define CONFIG_ENABLE_36BIT_PHYS	1
+
+/*
+ * Base addresses -- Note these are effective addresses where the
+ * actual resources get mapped (not physical addresses)
+ */
+#define CONFIG_SYS_CCSRBAR_DEFAULT	0xff700000	/* CCSRBAR Default */
+#define CONFIG_SYS_CCSRBAR		0xef000000	/* relocated CCSRBAR */
+#define CONFIG_SYS_CCSRBAR_PHYS	CONFIG_SYS_CCSRBAR	/* physical addr of CCSRBAR */
+#define CONFIG_SYS_IMMR		CONFIG_SYS_CCSRBAR	/* PQII uses CONFIG_SYS_IMMR */
+
+/*
+ * Diagnostics
+ */
+#define CONFIG_SYS_ALT_MEMTEST
+#define CONFIG_SYS_MEMTEST_START	0x10000000
+#define CONFIG_SYS_MEMTEST_END		0x20000000
+
+/*
+ * Memory map
+ * 0x0000_0000	0x7fff_ffff	DDR			2G Cacheable
+ * 0x8000_0000	0xbfff_ffff	PCI1 Mem		1G non-cacheable
+ * 0xe000_0000	0xe7ff_ffff	SRAM/SSRAM/L1 Cache	128M non-cacheable
+ * 0xe800_0000	0xe87f_ffff	PCI1 IO			8M non-cacheable
+ * 0xef00_0000	0xef0f_ffff	CCSR/IMMR		1M non-cacheable
+ * 0xef80_0000	0xef8f_ffff	NAND Flash		1M non-cacheable
+ * 0xf800_0000	0xfbff_ffff	NOR Flash 2		64M non-cacheable
+ * 0xfc00_0000	0xffff_ffff	NOR Flash 1		64M non-cacheable
+ */
+
+#define CONFIG_SYS_LBC_LCRR	(LCRR_CLKDIV_8 | LCRR_EADC_3)
+
+/*
+ * NAND flash configuration
+ */
+#define CONFIG_SYS_NAND_BASE		0xef800000
+#define CONFIG_SYS_NAND_BASE2		0xef840000 /* Unused at this time */
+#define CONFIG_SYS_MAX_NAND_DEVICE	1
+#define CONFIG_NAND_ACTL
+#define CONFIG_SYS_NAND_ACTL_CLE	(1 << 3)	/* ADDR3 is CLE */
+#define CONFIG_SYS_NAND_ACTL_ALE	(1 << 4)	/* ADDR4 is ALE */
+#define CONFIG_SYS_NAND_ACTL_NCE	(0)		/* NCE not controlled by ADDR */
+#define CONFIG_SYS_NAND_ACTL_DELAY	25
+
+/*
+ * NOR flash configuration
+ */
+#define CONFIG_SYS_FLASH_BASE		0xfc000000
+#define CONFIG_SYS_FLASH_BASE2		0xf8000000
+#define CONFIG_SYS_FLASH_BANKS_LIST	{CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE2}
+#define CONFIG_SYS_MAX_FLASH_BANKS	2		/* number of banks */
+#define CONFIG_SYS_MAX_FLASH_SECT	1024		/* sectors per device */
+#define CONFIG_SYS_FLASH_ERASE_TOUT	60000		/* Flash Erase Timeout (ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT	500		/* Flash Write Timeout (ms) */
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
+#define CONFIG_SYS_FLASH_AUTOPROTECT_LIST	{ {0xfff40000, 0xc0000}, \
+						  {0xfbf40000, 0xc0000} }
+#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE	/* start of monitor */
+
+/*
+ * Chip select configuration
+ */
+/* NOR Flash 0 on CS0 */
+#define CONFIG_SYS_BR0_PRELIM	(CONFIG_SYS_FLASH_BASE	| \
+				 BR_PS_16		| \
+				 BR_V)
+#define CONFIG_SYS_OR0_PRELIM	(OR_AM_64MB		| \
+				 OR_GPCM_ACS_DIV4	| \
+				 OR_GPCM_SCY_8)
+
+/* NOR Flash 1 on CS1 */
+#define CONFIG_SYS_BR1_PRELIM	(CONFIG_SYS_FLASH_BASE2	| \
+				 BR_PS_16		| \
+				 BR_V)
+#define CONFIG_SYS_OR1_PRELIM	CONFIG_SYS_OR0_PRELIM
+
+/* NAND flash on CS2 */
+#define CONFIG_SYS_BR2_PRELIM	(CONFIG_SYS_NAND_BASE	| \
+				 BR_PS_8		| \
+				 BR_V)
+
+/* NAND flash on CS2 */
+#define CONFIG_SYS_OR2_PRELIM	(OR_AM_256KB		| \
+				 OR_GPCM_BCTLD		| \
+				 OR_GPCM_CSNT		| \
+				 OR_GPCM_ACS_DIV4	| \
+				 OR_GPCM_SCY_4		| \
+				 OR_GPCM_TRLX		| \
+				 OR_GPCM_EHTR)
+
+/* NAND flash on CS3 */
+#define CONFIG_SYS_BR3_PRELIM	(CONFIG_SYS_NAND_BASE2	| \
+				 BR_PS_8		| \
+				 BR_V)
+#define CONFIG_SYS_OR3_PRELIM	CONFIG_SYS_OR2_PRELIM
+
+/*
+ * Use L1 as initial stack
+ */
+#define CONFIG_SYS_INIT_RAM_LOCK	1
+#define CONFIG_SYS_INIT_RAM_ADDR	0xe0000000
+#define CONFIG_SYS_INIT_RAM_END		0x4000
+
+#define CONFIG_SYS_GBL_DATA_SIZE	128		/* num bytes initial data */
+#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
+
+#define CONFIG_SYS_MONITOR_LEN		(512 * 1024)	/* Reserve 512 KB for Mon */
+#define CONFIG_SYS_MALLOC_LEN		(1024 * 1024)	/* Reserved for malloc */
+
+/*
+ * Serial Port
+ */
+#define CONFIG_CONS_INDEX		1
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE	1
+#define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)
+#define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_CCSRBAR+0x4500)
+#define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_CCSRBAR+0x4600)
+#define CONFIG_SYS_BAUDRATE_TABLE	\
+	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
+#define CONFIG_BAUDRATE			115200
+#define CONFIG_LOADS_ECHO		1	/* echo on for serial download */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change */
+
+/*
+ * Use the HUSH parser
+ */
+#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2	"> "
+
+/*
+ * Pass open firmware flat tree
+ */
+#define CONFIG_OF_LIBFDT		1
+#define CONFIG_OF_BOARD_SETUP		1
+#define CONFIG_OF_STDOUT_VIA_ALIAS	1
+
+/*
+ * I2C
+ */
+#define CONFIG_FSL_I2C				/* Use FSL common I2C driver */
+#define CONFIG_HARD_I2C				/* I2C with hardware support */
+#define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address */
+#define CONFIG_SYS_I2C_SLAVE		0x7F
+#define CONFIG_SYS_I2C_OFFSET		0x3000
+#define CONFIG_SYS_I2C2_OFFSET		0x3100
+#define CONFIG_I2C_MULTI_BUS
+
+/* I2C EEPROM */
+#define CONFIG_SYS_I2C_EEPROM_ADDR		0x50
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		1
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	6	/* 64 byte pages */
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	10	/* take up to 10 msec */
+
+/* I2C RTC */
+#define CONFIG_RTC_M41T11			1
+#define CONFIG_SYS_I2C_RTC_ADDR			0x68
+#define CONFIG_SYS_M41T11_BASE_YEAR		2000
+
+/* GPIO */
+#define CONFIG_PCA953X
+#define CONFIG_SYS_I2C_PCA953X_ADDR0		0x18
+#define CONFIG_SYS_I2C_PCA953X_ADDR1		0x19
+#define CONFIG_SYS_I2C_PCA953X_ADDR		CONFIG_SYS_I2C_PCA953X_ADDR0
+
+/* PCA957 @ 0x18 */
+#define CONFIG_SYS_PCA953X_BRD_CFG0		0x01
+#define CONFIG_SYS_PCA953X_BRD_CFG1		0x02
+#define CONFIG_SYS_PCA953X_BRD_CFG2		0x04
+#define CONFIG_SYS_PCA953X_XMC_ROOT0		0x08
+#define CONFIG_SYS_PCA953X_FLASH_PASS_CS	0x10
+#define CONFIG_SYS_PCA953X_NVM_WP		0x20
+#define CONFIG_SYS_PCA953X_MONARCH		0x40
+#define CONFIG_SYS_PCA953X_EREADY		0x80
+
+/* PCA957 @ 0x19 */
+#define CONFIG_SYS_PCA953X_P14_IO0		0x01
+#define CONFIG_SYS_PCA953X_P14_IO1		0x02
+#define CONFIG_SYS_PCA953X_P14_IO2		0x04
+#define CONFIG_SYS_PCA953X_P14_IO3		0x08
+#define CONFIG_SYS_PCA953X_P14_IO4		0x10
+#define CONFIG_SYS_PCA953X_P14_IO5		0x20
+#define CONFIG_SYS_PCA953X_P14_IO6		0x40
+#define CONFIG_SYS_PCA953X_P14_IO7		0x80
+
+/*
+ * General PCI
+ * Memory space is mapped 1-1, but I/O space must start from 0.
+ */
+#define CONFIG_SYS_PCI1_MEM_BUS		0x80000000
+#define CONFIG_SYS_PCI1_MEM_PHYS	CONFIG_SYS_PCI1_MEM_BUS
+#define CONFIG_SYS_PCI1_MEM_SIZE	0x40000000	/* 1G */
+#define CONFIG_SYS_PCI1_IO_BUS		0x00000000
+#define CONFIG_SYS_PCI1_IO_PHYS		0xe8000000
+#define CONFIG_SYS_PCI1_IO_SIZE		0x00800000	/* 1M */
+
+/*
+ * Networking options
+ */
+#define CONFIG_TSEC_ENET		/* tsec ethernet support */
+#define CONFIG_PHY_GIGE		1	/* Include GbE speed/duplex detection */
+#define CONFIG_NET_MULTI	1
+#define CONFIG_MII		1	/* MII PHY management */
+#define CONFIG_ETHPRIME		"eTSEC1"
+
+#define CONFIG_TSEC1		1
+#define CONFIG_TSEC1_NAME	"eTSEC1"
+#define TSEC1_FLAGS		TSEC_GIGABIT
+#define TSEC1_PHY_ADDR		1
+#define TSEC1_PHYIDX		0
+#define CONFIG_HAS_ETH0
+
+#define CONFIG_TSEC2		1
+#define CONFIG_TSEC2_NAME	"eTSEC2"
+#define TSEC2_FLAGS		TSEC_GIGABIT
+#define TSEC2_PHY_ADDR		2
+#define TSEC2_PHYIDX		0
+#define CONFIG_HAS_ETH1
+
+#define CONFIG_TSEC3	1
+#define CONFIG_TSEC3_NAME	"eTSEC3"
+#define TSEC3_FLAGS		TSEC_GIGABIT
+#define TSEC3_PHY_ADDR		3
+#define TSEC3_PHYIDX		0
+#define CONFIG_HAS_ETH2
+
+#define CONFIG_TSEC4	1
+#define CONFIG_TSEC4_NAME	"eTSEC4"
+#define TSEC4_FLAGS		TSEC_GIGABIT
+#define TSEC4_PHY_ADDR		4
+#define TSEC4_PHYIDX		0
+#define CONFIG_HAS_ETH3
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+
+/*
+ * Command configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_SAVEENV
+#define CONFIG_CMD_FLASH
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_JFFS2
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_PCA953X
+#define CONFIG_CMD_PCA953X_INFO
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_PCI_ENUM
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_SNTP
+#define CONFIG_CMD_REGINFO
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LONGHELP			/* undef to save memory	*/
+#define CONFIG_SYS_LOAD_ADDR	0x2000000	/* default load address */
+#define CONFIG_SYS_PROMPT	"=> "		/* Monitor Command Prompt */
+#define CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS	16		/* max number of command args */
+#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size */
+#define CONFIG_SYS_HZ		1000		/* decrementer freq: 1ms ticks */
+#define CONFIG_CMDLINE_EDITING	1		/* add command line history	*/
+#define CONFIG_AUTO_COMPLETE	1		/* add autocompletion support */
+#define CONFIG_LOADADDR		0x1000000	/* default location for tftp and bootm */
+#define CONFIG_BOOTDELAY	3		/* -1 disables auto-boot */
+#define CONFIG_PANIC_HANG			/* do not reset board on panic */
+#define CONFIG_PREBOOT				/* enable preboot variable */
+#define CONFIG_FIT		1
+#define CONFIG_FIT_VERBOSE	1
+#define CONFIG_INTEGRITY			/* support booting INTEGRITY OS */
+#define CONFIG_INTERRUPTS		/* enable pci, srio, ddr interrupts */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 16 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ	(16 << 20)	/* Initial Memory map for Linux*/
+#define CONFIG_SYS_BOOTM_LEN	(16 << 20)	/* Increase max gunzip size */
+
+/*
+ * Environment Configuration
+ */
+#define CONFIG_ENV_IS_IN_FLASH	1
+#define CONFIG_ENV_SECT_SIZE	0x20000		/* 128k (one sector) for env */
+#define CONFIG_ENV_SIZE		0x8000
+#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - (256 * 1024))
+
+/*
+ * Flash memory map:
+ * fff80000 - ffffffff     Pri U-Boot (512 KB)
+ * fff40000 - fff7ffff     Pri U-Boot Environment (256 KB)
+ * fff00000 - fff3ffff     Pri FDT (256KB)
+ * fef00000 - ffefffff     Pri OS image (16MB)
+ * fc000000 - feefffff     Pri OS Use/Filesystem (47MB)
+ *
+ * fbf80000 - fbffffff     Sec U-Boot (512 KB)
+ * fbf40000 - fbf7ffff     Sec U-Boot Environment (256 KB)
+ * fbf00000 - fbf3ffff     Sec FDT (256KB)
+ * faf00000 - fbefffff     Sec OS image (16MB)
+ * f8000000 - faefffff     Sec OS Use/Filesystem (47MB)
+ */
+#define CONFIG_UBOOT1_ENV_ADDR	MK_STR(0xfff80000)
+#define CONFIG_UBOOT2_ENV_ADDR	MK_STR(0xfbf80000)
+#define CONFIG_FDT1_ENV_ADDR	MK_STR(0xfff00000)
+#define CONFIG_FDT2_ENV_ADDR	MK_STR(0xfbf00000)
+#define CONFIG_OS1_ENV_ADDR	MK_STR(0xfef00000)
+#define CONFIG_OS2_ENV_ADDR	MK_STR(0xfaf00000)
+
+#define CONFIG_PROG_UBOOT1						\
+	"$download_cmd $loadaddr $ubootfile; "				\
+	"if test $? -eq 0; then "					\
+		"protect off "CONFIG_UBOOT1_ENV_ADDR" +80000; "		\
+		"erase "CONFIG_UBOOT1_ENV_ADDR" +80000; "		\
+		"cp.w $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 40000; "	\
+		"protect on "CONFIG_UBOOT1_ENV_ADDR" +80000; "		\
+		"cmp.b $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 80000; "	\
+		"if test $? -ne 0; then "				\
+			"echo PROGRAM FAILED; "				\
+		"else; "						\
+			"echo PROGRAM SUCCEEDED; "			\
+		"fi; "							\
+	"else; "							\
+		"echo DOWNLOAD FAILED; "				\
+	"fi;"
+
+#define CONFIG_PROG_UBOOT2						\
+	"$download_cmd $loadaddr $ubootfile; "				\
+	"if test $? -eq 0; then "					\
+		"protect off "CONFIG_UBOOT2_ENV_ADDR" +80000; "		\
+		"erase "CONFIG_UBOOT2_ENV_ADDR" +80000; "		\
+		"cp.w $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 40000; "	\
+		"protect on "CONFIG_UBOOT2_ENV_ADDR" +80000; "		\
+		"cmp.b $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 80000; "	\
+		"if test $? -ne 0; then "				\
+			"echo PROGRAM FAILED; "				\
+		"else; "						\
+			"echo PROGRAM SUCCEEDED; "			\
+		"fi; "							\
+	"else; "							\
+		"echo DOWNLOAD FAILED; "				\
+	"fi;"
+
+#define CONFIG_BOOT_OS_NET						\
+	"$download_cmd $osaddr $osfile; "				\
+	"if test $? -eq 0; then "					\
+		"if test -n $fdtaddr; then "				\
+			"$download_cmd $fdtaddr $fdtfile; "		\
+			"if test $? -eq 0; then "			\
+				"bootm $osaddr - $fdtaddr; "		\
+			"else; "					\
+				"echo FDT DOWNLOAD FAILED; "		\
+			"fi; "						\
+		"else; "						\
+			"bootm $osaddr; "				\
+		"fi; "							\
+	"else; "							\
+		"echo OS DOWNLOAD FAILED; "				\
+	"fi;"
+
+#define CONFIG_PROG_OS1							\
+	"$download_cmd $osaddr $osfile; "				\
+	"if test $? -eq 0; then "					\
+		"erase "CONFIG_OS1_ENV_ADDR" +$filesize; "		\
+		"cp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; "	\
+		"cmp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; "	\
+		"if test $? -ne 0; then "				\
+			"echo OS PROGRAM FAILED; "			\
+		"else; "						\
+			"echo OS PROGRAM SUCCEEDED; "			\
+		"fi; "							\
+	"else; "							\
+		"echo OS DOWNLOAD FAILED; "				\
+	"fi;"
+
+#define CONFIG_PROG_OS2							\
+	"$download_cmd $osaddr $osfile; "				\
+	"if test $? -eq 0; then "					\
+		"erase "CONFIG_OS2_ENV_ADDR" +$filesize; "		\
+		"cp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; "	\
+		"cmp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; "	\
+		"if test $? -ne 0; then "				\
+			"echo OS PROGRAM FAILED; "			\
+		"else; "						\
+			"echo OS PROGRAM SUCCEEDED; "			\
+		"fi; "							\
+	"else; "							\
+		"echo OS DOWNLOAD FAILED; "				\
+	"fi;"
+
+#define CONFIG_PROG_FDT1						\
+	"$download_cmd $fdtaddr $fdtfile; "				\
+	"if test $? -eq 0; then "					\
+		"erase "CONFIG_FDT1_ENV_ADDR" +$filesize;"		\
+		"cp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; "	\
+		"cmp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; "	\
+		"if test $? -ne 0; then "				\
+			"echo FDT PROGRAM FAILED; "			\
+		"else; "						\
+			"echo FDT PROGRAM SUCCEEDED; "			\
+		"fi; "							\
+	"else; "							\
+		"echo FDT DOWNLOAD FAILED; "				\
+	"fi;"
+
+#define CONFIG_PROG_FDT2						\
+	"$download_cmd $fdtaddr $fdtfile; "				\
+	"if test $? -eq 0; then "					\
+		"erase "CONFIG_FDT2_ENV_ADDR" +$filesize;"		\
+		"cp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; "	\
+		"cmp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; "	\
+		"if test $? -ne 0; then "				\
+			"echo FDT PROGRAM FAILED; "			\
+		"else; "						\
+			"echo FDT PROGRAM SUCCEEDED; "			\
+		"fi; "							\
+	"else; "							\
+		"echo FDT DOWNLOAD FAILED; "				\
+	"fi;"
+
+#define	CONFIG_EXTRA_ENV_SETTINGS					\
+	"autoload=yes\0"						\
+	"download_cmd=tftp\0"						\
+	"console_args=console=ttyS0,115200\0"				\
+	"root_args=root=/dev/nfs rw\0"					\
+	"misc_args=ip=on\0"						\
+	"set_bootargs=setenv bootargs ${console_args} ${root_args} ${misc_args}\0" \
+	"bootfile=/home/user/file\0"					\
+	"osfile=/home/user/board.uImage\0"				\
+	"fdtfile=/home/user/board.dtb\0"				\
+	"ubootfile=/home/user/u-boot.bin\0"				\
+	"fdtaddr=c00000\0"						\
+	"osaddr=0x1000000\0"						\
+	"loadaddr=0x1000000\0"						\
+	"prog_uboot1="CONFIG_PROG_UBOOT1"\0"				\
+	"prog_uboot2="CONFIG_PROG_UBOOT2"\0"				\
+	"prog_os1="CONFIG_PROG_OS1"\0"					\
+	"prog_os2="CONFIG_PROG_OS2"\0"					\
+	"prog_fdt1="CONFIG_PROG_FDT1"\0"				\
+	"prog_fdt2="CONFIG_PROG_FDT2"\0"				\
+	"bootcmd_net=run set_bootargs; "CONFIG_BOOT_OS_NET"\0"		\
+	"bootcmd_flash1=run set_bootargs; "				\
+		"bootm "CONFIG_OS1_ENV_ADDR" - "CONFIG_FDT1_ENV_ADDR"\0"\
+	"bootcmd_flash2=run set_bootargs; "				\
+		"bootm "CONFIG_OS2_ENV_ADDR" - "CONFIG_FDT2_ENV_ADDR"\0"\
+	"bootcmd=run bootcmd_flash1\0"
+#endif	/* __CONFIG_H */