/*
 * board/renesas/koelsch/koelsch.c
 *
 * Copyright (C) 2013 Renesas Electronics Corporation
 *
 * SPDX-License-Identifier: GPL-2.0
 *
 */

#include <common.h>
#include <malloc.h>
#include <asm/processor.h>
#include <asm/mach-types.h>
#include <asm/io.h>
#include <asm/errno.h>
#include <asm/arch/sys_proto.h>
#include <asm/gpio.h>
#include <asm/arch/rmobile.h>
#include <netdev.h>
#include <miiphy.h>
#include <i2c.h>
#include <div64.h>
#include "qos.h"

DECLARE_GLOBAL_DATA_PTR;

#define CLK2MHZ(clk)	(clk / 1000 / 1000)
void s_init(void)
{
	struct rcar_rwdt *rwdt = (struct rcar_rwdt *)RWDT_BASE;
	struct rcar_swdt *swdt = (struct rcar_swdt *)SWDT_BASE;
	u32 stc;

	/* Watchdog init */
	writel(0xA5A5A500, &rwdt->rwtcsra);
	writel(0xA5A5A500, &swdt->swtcsra);

	/* CPU frequency setting. Set to 1.5GHz */
	stc = ((1500 / CLK2MHZ(CONFIG_SYS_CLK_FREQ)) - 1) << PLL0_STC_BIT;
	clrsetbits_le32(PLL0CR, PLL0_STC_MASK, stc);

	/* QoS */
	qos_init();
}

#define MSTPSR1		0xE6150038
#define SMSTPCR1	0xE6150134
#define TMU0_MSTP125	(1 << 25)

#define MSTPSR7		0xE61501C4
#define SMSTPCR7	0xE615014C
#define SCIF0_MSTP721	(1 << 21)

#define MSTPSR8		0xE61509A0
#define SMSTPCR8	0xE6150990
#define ETHER_MSTP813	(1 << 13)

#define mstp_setbits(type, addr, saddr, set) \
	out_##type((saddr), in_##type(addr) | (set))
#define mstp_clrbits(type, addr, saddr, clear) \
	out_##type((saddr), in_##type(addr) & ~(clear))
#define mstp_setbits_le32(addr, saddr, set) \
	mstp_setbits(le32, addr, saddr, set)
#define mstp_clrbits_le32(addr, saddr, clear)   \
	mstp_clrbits(le32, addr, saddr, clear)

int board_early_init_f(void)
{
	mstp_clrbits_le32(MSTPSR1, SMSTPCR1, TMU0_MSTP125);

	/* SCIF0 */
	mstp_clrbits_le32(MSTPSR7, SMSTPCR7, SCIF0_MSTP721);

	/* ETHER */
	mstp_clrbits_le32(MSTPSR8, SMSTPCR8, ETHER_MSTP813);

	return 0;
}

void arch_preboot_os(void)
{
	/* Disable TMU0 */
	mstp_setbits_le32(MSTPSR1, SMSTPCR1, TMU0_MSTP125);
}

/* LSI pin pull-up control */
#define PUPR5 0xe6060114
#define PUPR5_ETH 0x3FFC0000
#define PUPR5_ETH_MAGIC	(1 << 27)
int board_init(void)
{
	/* adress of boot parameters */
	gd->bd->bi_boot_params = KOELSCH_SDRAM_BASE + 0x100;

	/* Init PFC controller */
	r8a7791_pinmux_init();

	/* ETHER Enable */
	gpio_request(GPIO_FN_ETH_CRS_DV, NULL);
	gpio_request(GPIO_FN_ETH_RX_ER, NULL);
	gpio_request(GPIO_FN_ETH_RXD0, NULL);
	gpio_request(GPIO_FN_ETH_RXD1, NULL);
	gpio_request(GPIO_FN_ETH_LINK, NULL);
	gpio_request(GPIO_FN_ETH_REFCLK, NULL);
	gpio_request(GPIO_FN_ETH_MDIO, NULL);
	gpio_request(GPIO_FN_ETH_TXD1, NULL);
	gpio_request(GPIO_FN_ETH_TX_EN, NULL);
	gpio_request(GPIO_FN_ETH_TXD0, NULL);
	gpio_request(GPIO_FN_ETH_MDC, NULL);
	gpio_request(GPIO_FN_IRQ0, NULL);

	mstp_clrbits_le32(PUPR5, PUPR5, PUPR5_ETH & ~PUPR5_ETH_MAGIC);
	gpio_request(GPIO_GP_5_22, NULL); /* PHY_RST */
	mstp_clrbits_le32(PUPR5, PUPR5, PUPR5_ETH_MAGIC);

	gpio_direction_output(GPIO_GP_5_22, 0);
	mdelay(20);
	gpio_set_value(GPIO_GP_5_22, 1);
	udelay(1);

	return 0;
}

#define CXR24 0xEE7003C0 /* MAC address high register */
#define CXR25 0xEE7003C8 /* MAC address low register */
int board_eth_init(bd_t *bis)
{
#ifdef CONFIG_SH_ETHER
	int ret = -ENODEV;
	u32 val;
	unsigned char enetaddr[6];

	ret = sh_eth_initialize(bis);
	if (!eth_getenv_enetaddr("ethaddr", enetaddr))
		return ret;

	/* Set Mac address */
	val = enetaddr[0] << 24 | enetaddr[1] << 16 |
		enetaddr[2] << 8 | enetaddr[3];
	writel(val, CXR24);

	val = enetaddr[4] << 8 | enetaddr[5];
	writel(val, CXR25);

	return ret;
#else
	return 0;
#endif
}

int dram_init(void)
{
	gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE;
	gd->ram_size = CONFIG_SYS_SDRAM_SIZE;

	return 0;
}

/* koelsch has KSZ8041NL/RNL */
#define PHY_CONTROL1	0x1E
#define PHY_LED_MODE	0xC0000
#define PHY_LED_MODE_ACK	0x4000
int board_phy_config(struct phy_device *phydev)
{
	int ret = phy_read(phydev, MDIO_DEVAD_NONE, PHY_CONTROL1);
	ret &= ~PHY_LED_MODE;
	ret |= PHY_LED_MODE_ACK;
	ret = phy_write(phydev, MDIO_DEVAD_NONE, PHY_CONTROL1, (u16)ret);

	return 0;
}

const struct rmobile_sysinfo sysinfo = {
	CONFIG_RMOBILE_BOARD_STRING
};

void dram_init_banksize(void)
{
	gd->bd->bi_dram[0].start = KOELSCH_SDRAM_BASE;
	gd->bd->bi_dram[0].size = KOELSCH_SDRAM_SIZE;
}

int board_late_init(void)
{
	return 0;
}

void reset_cpu(ulong addr)
{
	u8 val;

	i2c_set_bus_num(2); /* PowerIC connected to ch2 */
	i2c_read(CONFIG_SYS_I2C_POWERIC_ADDR, 0x13, 1, &val, 1);
	val |= 0x02;
	i2c_write(CONFIG_SYS_I2C_POWERIC_ADDR, 0x13, 1, &val, 1);
}