diff --git a/board/mpl/common/common_util.c b/board/mpl/common/common_util.c
index 9c98c93..5117394 100644
--- a/board/mpl/common/common_util.c
+++ b/board/mpl/common/common_util.c
@@ -42,6 +42,9 @@
 #include "../mip405/mip405.h"
 #include <405gp_pci.h>
 #endif
+#if defined(CONFIG_PATI)
+#define FIRM_START 0xFFF00000
+#endif
 
 extern int gunzip(void *, int, uchar *, int *);
 extern int mem_test(ulong start, ulong ramsize, int quiet);
@@ -60,14 +63,17 @@
 	ulong start;
 	flash_info_t *info;
 	int i, rc;
-#if defined(CONFIG_PIP405) || defined(CONFIG_MIP405)
+#if defined(CONFIG_PATI)
+	int start_sect;
+#endif
+#if defined(CONFIG_PIP405) || defined(CONFIG_MIP405) || defined(CONFIG_PATI)
 	char *copystr = (char *)src;
 	ulong *magic = (ulong *)src;
 #endif
 
 	info = &flash_info[0];
 
-#if defined(CONFIG_PIP405) || defined(CONFIG_MIP405)
+#if defined(CONFIG_PIP405) || defined(CONFIG_MIP405) || defined(CONFIG_PATI)
 	if (ntohl(magic[0]) != IH_MAGIC) {
 		puts("Bad Magic number\n");
 		return -1;
@@ -90,6 +96,7 @@
 		printf("Wrong Firmware Image: %s\n", &copystr[i]);
 		return -1;
 	}
+#if !defined(CONFIG_PATI)
 	start = 0 - size;
 	for (i = info->sector_count-1; i > 0; i--) {
 		info->protect[i] = 0; /* unprotect this sector */
@@ -106,6 +113,36 @@
 		return (1);
 	}
 
+#else /* #if !defined(CONFIG_PATI */
+	start = FIRM_START;
+	start_sect = -1;
+	for (i = 0; i < info->sector_count; i++) {
+		if (start < info->start[i]) {
+			start_sect = i - 1;
+			break;
+		}
+	}
+
+	info->protect[i - 1] = 0;	/* unprotect this sector */
+	for (; i < info->sector_count; i++) {
+		if ((start + size) < info->start[i])
+			break;
+		info->protect[i] = 0;	/* unprotect this sector */
+	}
+
+	i--;
+	/* set-up flash location */
+	/* now erase flash */
+	printf ("Erasing at %lx to %lx (sector %d to %d) (%lx to %lx)\n",
+		start, start + size, start_sect, i,
+		info->start[start_sect], info->start[i]);
+	if ((rc = flash_erase (info, start_sect, i)) != 0) {
+		puts ("ERROR ");
+		flash_perror (rc);
+		return (1);
+	}
+#endif /* defined(CONFIG_PATI) */
+
 #elif defined(CONFIG_VCMA9)
 	start = 0;
 	for (i = 0; i <info->sector_count; i++) {
@@ -227,7 +264,7 @@
 	return(rc);
 }
 
-
+#if !defined(CONFIG_PATI)
 void get_backup_values(backup_t *buf)
 {
 	i2c_read(CFG_DEF_EEPROM_ADDR, I2C_BACKUP_ADDR,2,(void *)buf,sizeof(backup_t));
@@ -417,14 +454,17 @@
 	}
 }
 
+#endif /* #if !defined(CONFIG_PATI) */
 
 int do_mplcommon(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
 {
  	ulong size,src,ld_addr;
 	int result;
+#if !defined(CONFIG_PATI)
 	backup_t back;
 	src = MULTI_PURPOSE_SOCKET_ADDR;
 	size = IMAGE_SIZE;
+#endif
 
 	if (strcmp(argv[1], "flash") == 0)
 	{
@@ -460,11 +500,13 @@
 			result=mpl_prg_image((uchar *)ld_addr);
 			return result;
 		}
+#if !defined(CONFIG_PATI)
 		if (strcmp(argv[2], "mps") == 0) {
 			puts("\nupdating bootloader image from MPS\n");
 			result=mpl_prg((uchar *)src,size);
 			return result;
 		}
+#endif /* #if !defined(CONFIG_PATI)	*/
 	}
 	if (strcmp(argv[1], "mem") == 0)
 	{
@@ -490,6 +532,7 @@
 		}while(result);
 		return 0;
 	}
+#if !defined(CONFIG_PATI)
 	if (strcmp(argv[1], "clearenvvalues") == 0)
 	{
  		if (strcmp(argv[2], "yes") == 0)
@@ -512,6 +555,7 @@
 		set_backup_values(1);
 		return 0;
 	}
+#endif
 	printf("Usage:\n%s\n", cmdtp->usage);
 	return 1;
 }
diff --git a/board/mpl/common/flash.c b/board/mpl/common/flash.c
index 5f50200..fd43008 100644
--- a/board/mpl/common/flash.c
+++ b/board/mpl/common/flash.c
@@ -36,6 +36,8 @@
  */
 
 #include <common.h>
+
+#if !defined(CONFIG_PATI)
 #include <ppc4xx.h>
 #include <asm/processor.h>
 #include "common_util.h"
@@ -46,6 +48,9 @@
 #include "../pip405/pip405.h"
 #endif
 #include <405gp_pci.h>
+#else /* defined(CONFIG_PATI) */
+#include <mpc5xx.h>
+#endif
 
 flash_info_t	flash_info[CFG_MAX_FLASH_BANKS]; /* info for FLASH chips	*/
 /*-----------------------------------------------------------------------
@@ -56,22 +61,15 @@
 
 void unlock_intel_sectors(flash_info_t *info,ulong addr,ulong cnt);
 
-
-#ifdef CONFIG_PIP405
 #define ADDR0           0x5555
 #define ADDR1           0x2aaa
 #define FLASH_WORD_SIZE unsigned short
-#endif
-
-#ifdef CONFIG_MIP405
-#define ADDR0           0x5555
-#define ADDR1           0x2aaa
-#define FLASH_WORD_SIZE unsigned short
-#endif
 
 #define FALSE           0
 #define TRUE            1
 
+#if !defined(CONFIG_PATI)
+
 /*-----------------------------------------------------------------------
  * Some CS switching routines:
  *
@@ -151,11 +149,16 @@
 	}
 }
 
+#endif /* #if !defined(CONFIG_PATI) */
 
 unsigned long flash_init (void)
 {
-	unsigned long size_b0, size_b1,flashcr, size_reg;
-	int mode, i;
+	unsigned long size_b0;
+	int i;
+
+#if !defined(CONFIG_PATI)
+	unsigned long size_b1,flashcr,size_reg;
+	int mode;
 	extern char version_string;
 	char *p=&version_string;
 
@@ -169,6 +172,7 @@
 	else
 		printf("(%s Boot) ",(mode & BOOT_MPS) ?
 			"MPS" : "Flash");
+#endif /* #if !defined(CONFIG_PATI) */
 	/* Init: no FLASHes known */
 	for (i=0; i<CFG_MAX_FLASH_BANKS; ++i) {
 		flash_info[i].flash_id = FLASH_UNKNOWN;
@@ -190,6 +194,7 @@
 			CFG_MONITOR_BASE+monitor_flash_len-1,
 			&flash_info[0]);
 #endif
+#if !defined(CONFIG_PATI)
 	/* protect reset vector */
 	flash_info[0].protect[flash_info[0].sector_count-1] = 1;
 	size_b1 = 0 ;
@@ -233,7 +238,7 @@
 		mtdcr(ebccfgd, flashcr);
 	}
 #if 0
-	/* enable this if you want to test if
+	/* enable this (PIP405/MIP405 only) if you want to test if
 	   the relocation has be done ok.
 	   This will disable both Chipselects */
 	mtdcr (ebccfga, pb0cr);
@@ -250,6 +255,15 @@
 		}
 		p++;
 	}
+#else /* #if !defined(CONFIG_PATI) */
+#ifdef	CFG_ENV_IS_IN_FLASH
+	/* ENV protection ON by default */
+	flash_protect(FLAG_PROTECT_SET,
+		      CFG_ENV_ADDR,
+		      CFG_ENV_ADDR+CFG_ENV_SECT_SIZE-1,
+		      &flash_info[0]);
+#endif
+#endif /* #if !defined(CONFIG_PATI) */
 	return (size_b0);
 }
 
diff --git a/board/mpl/pati/Makefile b/board/mpl/pati/Makefile
new file mode 100644
index 0000000..1a9ce12
--- /dev/null
+++ b/board/mpl/pati/Makefile
@@ -0,0 +1,48 @@
+#
+# (C) Copyright 2001	Wolfgang Denk, DENX Software Engineering, wd@denx.de
+#
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= lib$(BOARD).a
+
+OBJS	:=  pati.o ../common/flash.o ../common/memtst.o cmd_pati.o ../common/common_util.o
+#### cmd_pati.o
+SOBJS	:=
+
+$(LIB):	$(OBJS)
+	$(AR) crv $@ $(OBJS)
+
+clean:
+	rm -f $(SOBJS) $(OBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+.depend:	Makefile $(SOBJS:.o=.S) $(OBJS:.o=.c)
+		$(CC) -M $(CPPFLAGS) $(SOBJS:.o=.S) $(OBJS:.o=.c) > $@
+
+-include .depend
+
+#########################################################################
diff --git a/board/mpl/pati/cmd_pati.c b/board/mpl/pati/cmd_pati.c
new file mode 100644
index 0000000..cdab286
--- /dev/null
+++ b/board/mpl/pati/cmd_pati.c
@@ -0,0 +1,451 @@
+/*
+ * (C) Copyright 2001
+ * Denis Peter, MPL AG Switzerland, d.peter@mpl.ch
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ * Adapted for PATI
+ */
+
+#include <common.h>
+#include <command.h>
+#define PLX9056_LOC
+#include "plx9056.h"
+#include "pati.h"
+#include "pci_eeprom.h"
+
+extern void show_pld_regs(void);
+extern int do_mplcommon(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]);
+
+extern void user_led0(int led_on);
+extern void user_led1(int led_on);
+
+/* ------------------------------------------------------------------------- */
+#if defined(CFG_PCI_CON_DEVICE)
+extern void pci_con_disc(void);
+extern void pci_con_connect(void);
+#endif
+
+/******************************************************************************
+ * Eeprom Support
+ ******************************************************************************/
+unsigned long get32(unsigned long addr)
+{
+	unsigned long *p=(unsigned long *)addr;
+	return *p;
+}
+
+void set32(unsigned long addr,unsigned long data)
+{
+	unsigned long *p=(unsigned long *)addr;
+	*p=data;
+}
+
+#define PCICFG_GET_REG(x)	(get32((x) + PCI_CONFIG_BASE))
+#define PCICFG_SET_REG(x,y)	(set32((x) + PCI_CONFIG_BASE,(y)))
+
+
+/******************************************************************************
+ * reload_pci_eeprom
+ ******************************************************************************/
+
+static void reload_pci_eeprom(void)
+{
+	unsigned long reg;
+	/* Set Bit 29 and clear it again */
+	reg=PCICFG_GET_REG(PCI9056_EEPROM_CTRL_STAT);
+	udelay(1);
+	/* set it*/
+	reg|=(1<<29);
+	PCICFG_SET_REG(PCI9056_EEPROM_CTRL_STAT,reg);
+	/* EECLK @ 33MHz = 125kHz
+	 * -> extra long load = 32 * 16bit = 512Bit @ 125kHz = 4.1msec
+	 * use 20msec
+	 */
+	udelay(20000); /* wait 20ms */
+	reg &= ~(1<<29); /* set it low */
+	PCICFG_SET_REG(PCI9056_EEPROM_CTRL_STAT,reg);
+	udelay(1); /* wait some time */
+}
+
+/******************************************************************************
+ * clock_pci_eeprom
+ ******************************************************************************/
+
+static void clock_pci_eeprom(void)
+{
+	unsigned long reg;
+	/* clock is low, data is valid */
+	reg=PCICFG_GET_REG(PCI9056_EEPROM_CTRL_STAT);
+	udelay(1);
+	/* set clck high */
+	reg|=(1<<24);
+	PCICFG_SET_REG(PCI9056_EEPROM_CTRL_STAT,reg);
+	udelay(1); /* wait some time */
+	reg &= ~(1<<24); /* set clock low */
+	PCICFG_SET_REG(PCI9056_EEPROM_CTRL_STAT,reg);
+	udelay(1); /* wait some time */
+}
+
+/******************************************************************************
+ * send_pci_eeprom_cmd
+ ******************************************************************************/
+static void send_pci_eeprom_cmd(unsigned long cmd, unsigned char len)
+{
+	unsigned long reg;
+	int i;
+	reg=PCICFG_GET_REG(PCI9056_EEPROM_CTRL_STAT);
+	/* Clear all EEPROM bits */
+	reg &= ~(0xF << 24);
+	/* Toggle EEPROM's Chip select to get it out of Shift Register Mode */
+	PCICFG_SET_REG(PCI9056_EEPROM_CTRL_STAT,reg);
+	udelay(1); /* wait some time */
+	/* Enable EEPROM Chip Select */
+	reg |= (1 << 25);
+	PCICFG_SET_REG(PCI9056_EEPROM_CTRL_STAT,reg);
+	/* Send EEPROM command - one bit at a time */
+	for (i = (int)(len-1); i >= 0; i--) {
+		/* Check if current bit is 0 or 1 */
+		if (cmd & (1 << i))
+			PCICFG_SET_REG(PCI9056_EEPROM_CTRL_STAT,(reg | (1<<26)));
+		else
+			PCICFG_SET_REG(PCI9056_EEPROM_CTRL_STAT,reg);
+		clock_pci_eeprom();
+	}
+}
+
+/******************************************************************************
+ * write_pci_eeprom_offs
+ ******************************************************************************/
+static void write_pci_eeprom_offs(unsigned short offset, unsigned short value)
+{
+	unsigned long reg;
+	int bitpos, cmdshft, cmdlen, timeout;
+	/* we're using the Eeprom 93CS66 */
+	cmdshft  = 2;
+	cmdlen = EE66_CMD_LEN;
+	/* Send Write_Enable command to EEPROM */
+	send_pci_eeprom_cmd((EE_WREN << cmdshft),cmdlen);
+	/* Send EEPROM Write command and offset to EEPROM */
+	send_pci_eeprom_cmd((EE_WRITE << cmdshft) | (offset / 2),cmdlen);
+	reg=PCICFG_GET_REG(PCI9056_EEPROM_CTRL_STAT);
+	/* Clear all EEPROM bits */
+	reg &= ~(0xF << 24);
+	/* Make sure EEDO Input is disabled for some PLX chips */
+	reg &= ~(1 << 31);
+	/* Enable EEPROM Chip Select */
+	reg |= (1 << 25);
+	/* Write 16-bit value to EEPROM - one bit at a time */
+	for (bitpos = 15; bitpos >= 0; bitpos--) {
+		/* Get bit value and shift into result */
+		if (value & (1 << bitpos))
+			PCICFG_SET_REG(PCI9056_EEPROM_CTRL_STAT,(reg | (1<<26)));
+		else
+			PCICFG_SET_REG(PCI9056_EEPROM_CTRL_STAT,reg );
+		clock_pci_eeprom();
+	} /* for */
+	/* Deselect Chip */
+	PCICFG_SET_REG(PCI9056_EEPROM_CTRL_STAT,reg & ~(1 << 25));
+	/* Re-select Chip */
+	PCICFG_SET_REG(PCI9056_EEPROM_CTRL_STAT,reg | (1 << 25));
+	/* A small delay is needed to let EEPROM complete */
+	timeout = 0;
+	do {
+		udelay(10);
+		reg=PCICFG_GET_REG(PCI9056_EEPROM_CTRL_STAT);
+		timeout++;
+	} while (((reg & (1 << 27)) == 0) && timeout < 20000);
+	/* Send Write_Disable command to EEPROM */
+	send_pci_eeprom_cmd((EE_WDS << cmdshft),cmdlen);
+	/* Clear Chip Select and all other EEPROM bits */
+	PCICFG_SET_REG(PCI9056_EEPROM_CTRL_STAT,reg & ~(0xF << 24));
+}
+
+
+/******************************************************************************
+ * read_pci_eeprom_offs
+ ******************************************************************************/
+static void read_pci_eeprom_offs(unsigned short offset, unsigned short *pvalue)
+{
+	unsigned long reg;
+	int bitpos, cmdshft, cmdlen;
+	/* we're using the Eeprom 93CS66 */
+	cmdshft  = 2;
+	cmdlen = EE66_CMD_LEN;
+	/* Send EEPROM read command and offset to EEPROM */
+	send_pci_eeprom_cmd((EE_READ << cmdshft) | (offset / 2),cmdlen);
+	/* Set EEPROM write output bit */
+	reg=PCICFG_GET_REG(PCI9056_EEPROM_CTRL_STAT);
+	/* Set EEDO Input enable */
+	reg |= (1 << 31);
+	PCICFG_SET_REG(PCI9056_EEPROM_CTRL_STAT,reg | (1 << 26));
+	/* Get 16-bit value from EEPROM - one bit at a time */
+	for (bitpos = 0; bitpos < 16; bitpos++) {
+		clock_pci_eeprom();
+		udelay(10);
+		reg=PCICFG_GET_REG(PCI9056_EEPROM_CTRL_STAT);
+		/* Get bit value and shift into result */
+		if (reg & (1 << 27))
+			*pvalue = (unsigned short)((*pvalue << 1) | 1);
+		else
+			*pvalue = (unsigned short)(*pvalue << 1);
+	}
+	/* Clear EEDO Input enable */
+	reg &= ~(1 << 31);
+	/* Clear Chip Select and all other EEPROM bits */
+	PCICFG_SET_REG(PCI9056_EEPROM_CTRL_STAT,reg & ~(0xF << 24));
+}
+
+
+/******************************************************************************
+ * EEPROM read/writes
+******************************************************************************/
+
+#undef EEPROM_DBG
+static int pati_pci_eeprom_erase(void)
+{
+	int i;
+	printf("Erasing EEPROM ");
+	for( i=0; i < PATI_EEPROM_LAST_OFFSET; i+=2) {
+		write_pci_eeprom_offs(i,0xffff);
+		if((i%0x10))
+			printf(".");
+	}
+	printf("\nDone\n");
+	return 0;
+}
+
+static int pati_pci_eeprom_prg(void)
+{
+	int i;
+	i=0;
+	printf("Programming EEPROM ");
+	while(pati_eeprom[i].offset<0xffff) {
+		write_pci_eeprom_offs(pati_eeprom[i].offset,pati_eeprom[i].value);
+		#ifdef EEPROM_DBG
+		printf("0x%04X: 0x%04X\n",pati_eeprom[i].offset, pati_eeprom[i].value);
+		#else
+		if((i%0x10))
+			printf(".");
+		#endif
+		i++;
+	}
+	printf("\nDone\n");
+	return 0;
+}
+
+static int pati_pci_eeprom_write(unsigned short offset, unsigned long addr, unsigned short size)
+{
+	int i;
+	unsigned short value;
+	unsigned short *buffer =(unsigned short *)addr;
+	if((offset + size) > PATI_EEPROM_LAST_OFFSET) {
+		size = PATI_EEPROM_LAST_OFFSET - offset;
+	}
+	printf("Write To EEPROM from 0x%lX to 0x%X 0x%X words\n", addr, offset, size/2);
+	for( i = offset; i< (offset + size); i+=2) {
+		value = *buffer++;
+		write_pci_eeprom_offs(i,value);
+		#ifdef EEPROM_DBG
+		printf("0x%04X: 0x%04X\n",i, value);
+		#else
+		if((i%0x10))
+			printf(".");
+		#endif
+	}
+	printf("\nDone\n");
+	return 0;
+}
+
+static int pati_pci_eeprom_read(unsigned short offset, unsigned long addr, unsigned short size)
+{
+	int i;
+	unsigned short value;
+	unsigned short *buffer =(unsigned short *)addr;
+	if((offset + size) > PATI_EEPROM_LAST_OFFSET) {
+		size = PATI_EEPROM_LAST_OFFSET - offset;
+	}
+	printf("Read from EEPROM from 0x%X to 0x%lX 0x%X words\n", offset, addr, size/2);
+	for( i = offset; i< (offset + size); i+=2) {
+		read_pci_eeprom_offs(i,&value);
+		*buffer++=value;
+		#ifdef EEPROM_DBG
+		printf("0x%04X: 0x%04X\n",i, value);
+		#else
+		if((i%0x10))
+			printf(".");
+		#endif
+	}
+	printf("\nDone\n");
+	return 0;
+}
+
+
+
+/******************************************************************************
+ * PCI Bridge Registers Dump
+*******************************************************************************/
+static void display_pci_regs(void)
+{
+	printf(" PCI9056_SPACE0_RANGE     %08lX\n",PCICFG_GET_REG(PCI9056_SPACE0_RANGE));
+	printf(" PCI9056_SPACE0_REMAP     %08lX\n",PCICFG_GET_REG(PCI9056_SPACE0_REMAP));
+	printf(" PCI9056_LOCAL_DMA_ARBIT  %08lX\n",PCICFG_GET_REG(PCI9056_LOCAL_DMA_ARBIT));
+	printf(" PCI9056_ENDIAN_DESC      %08lX\n",PCICFG_GET_REG(PCI9056_ENDIAN_DESC));
+	printf(" PCI9056_EXP_ROM_RANGE    %08lX\n",PCICFG_GET_REG(PCI9056_EXP_ROM_RANGE));
+	printf(" PCI9056_EXP_ROM_REMAP    %08lX\n",PCICFG_GET_REG(PCI9056_EXP_ROM_REMAP));
+	printf(" PCI9056_SPACE0_ROM_DESC  %08lX\n",PCICFG_GET_REG(PCI9056_SPACE0_ROM_DESC));
+	printf(" PCI9056_DM_RANGE         %08lX\n",PCICFG_GET_REG(PCI9056_DM_RANGE));
+	printf(" PCI9056_DM_MEM_BASE      %08lX\n",PCICFG_GET_REG(PCI9056_DM_MEM_BASE));
+	printf(" PCI9056_DM_IO_BASE       %08lX\n",PCICFG_GET_REG(PCI9056_DM_IO_BASE));
+	printf(" PCI9056_DM_PCI_MEM_REMAP %08lX\n",PCICFG_GET_REG(PCI9056_DM_PCI_MEM_REMAP));
+	printf(" PCI9056_DM_PCI_IO_CONFIG %08lX\n",PCICFG_GET_REG(PCI9056_DM_PCI_IO_CONFIG));
+	printf(" PCI9056_SPACE1_RANGE     %08lX\n",PCICFG_GET_REG(PCI9056_SPACE1_RANGE));
+	printf(" PCI9056_SPACE1_REMAP     %08lX\n",PCICFG_GET_REG(PCI9056_SPACE1_REMAP));
+	printf(" PCI9056_SPACE1_DESC      %08lX\n",PCICFG_GET_REG(PCI9056_SPACE1_DESC));
+	printf(" PCI9056_DM_DAC           %08lX\n",PCICFG_GET_REG(PCI9056_DM_DAC));
+	printf(" PCI9056_MAILBOX0         %08lX\n",PCICFG_GET_REG(PCI9056_MAILBOX0));
+	printf(" PCI9056_MAILBOX1         %08lX\n",PCICFG_GET_REG(PCI9056_MAILBOX1));
+	printf(" PCI9056_MAILBOX2         %08lX\n",PCICFG_GET_REG(PCI9056_MAILBOX2));
+	printf(" PCI9056_MAILBOX3         %08lX\n",PCICFG_GET_REG(PCI9056_MAILBOX3));
+	printf(" PCI9056_MAILBOX4         %08lX\n",PCICFG_GET_REG(PCI9056_MAILBOX4));
+	printf(" PCI9056_MAILBOX5         %08lX\n",PCICFG_GET_REG(PCI9056_MAILBOX5));
+	printf(" PCI9056_MAILBOX6         %08lX\n",PCICFG_GET_REG(PCI9056_MAILBOX6));
+	printf(" PCI9056_MAILBOX7         %08lX\n",PCICFG_GET_REG(PCI9056_MAILBOX7));
+	printf(" PCI9056_PCI_TO_LOC_DBELL %08lX\n",PCICFG_GET_REG(PCI9056_PCI_TO_LOC_DBELL));
+	printf(" PCI9056_LOC_TO_PCI_DBELL %08lX\n",PCICFG_GET_REG(PCI9056_LOC_TO_PCI_DBELL));
+	printf(" PCI9056_INT_CTRL_STAT    %08lX\n",PCICFG_GET_REG(PCI9056_INT_CTRL_STAT));
+	printf(" PCI9056_EEPROM_CTRL_STAT %08lX\n",PCICFG_GET_REG(PCI9056_EEPROM_CTRL_STAT));
+	printf(" PCI9056_PERM_VENDOR_ID   %08lX\n",PCICFG_GET_REG(PCI9056_PERM_VENDOR_ID));
+	printf(" PCI9056_REVISION_ID      %08lX\n",PCICFG_GET_REG(PCI9056_REVISION_ID));
+	printf(" \n");
+	printf(" PCI9056_VENDOR_ID        %08lX\n",PCICFG_GET_REG(PCI9056_VENDOR_ID));
+	printf(" PCI9056_COMMAND          %08lX\n",PCICFG_GET_REG(PCI9056_COMMAND));
+	printf(" PCI9056_REVISION         %08lX\n",PCICFG_GET_REG(PCI9056_REVISION));
+	printf(" PCI9056_CACHE_SIZE       %08lX\n",PCICFG_GET_REG(PCI9056_CACHE_SIZE));
+	printf(" PCI9056_RTR_BASE         %08lX\n",PCICFG_GET_REG(PCI9056_RTR_BASE));
+	printf(" PCI9056_RTR_IO_BASE      %08lX\n",PCICFG_GET_REG(PCI9056_RTR_IO_BASE));
+	printf(" PCI9056_LOCAL_BASE0      %08lX\n",PCICFG_GET_REG(PCI9056_LOCAL_BASE0));
+	printf(" PCI9056_LOCAL_BASE1      %08lX\n",PCICFG_GET_REG(PCI9056_LOCAL_BASE1));
+	printf(" PCI9056_UNUSED_BASE1     %08lX\n",PCICFG_GET_REG(PCI9056_UNUSED_BASE1));
+	printf(" PCI9056_UNUSED_BASE2     %08lX\n",PCICFG_GET_REG(PCI9056_UNUSED_BASE2));
+	printf(" PCI9056_CIS_PTR          %08lX\n",PCICFG_GET_REG(PCI9056_CIS_PTR));
+	printf(" PCI9056_SUB_ID           %08lX\n",PCICFG_GET_REG(PCI9056_SUB_ID));
+	printf(" PCI9056_EXP_ROM_BASE     %08lX\n",PCICFG_GET_REG(PCI9056_EXP_ROM_BASE));
+	printf(" PCI9056_CAP_PTR          %08lX\n",PCICFG_GET_REG(PCI9056_CAP_PTR));
+	printf(" PCI9056_INT_LINE         %08lX\n",PCICFG_GET_REG(PCI9056_INT_LINE));
+	printf(" PCI9056_PM_CAP_ID        %08lX\n",PCICFG_GET_REG(PCI9056_PM_CAP_ID));
+	printf(" PCI9056_PM_CSR           %08lX\n",PCICFG_GET_REG(PCI9056_PM_CSR));
+	printf(" PCI9056_HS_CAP_ID        %08lX\n",PCICFG_GET_REG(PCI9056_HS_CAP_ID));
+	printf(" PCI9056_VPD_CAP_ID       %08lX\n",PCICFG_GET_REG(PCI9056_VPD_CAP_ID));
+	printf(" PCI9056_VPD_DATA         %08lX\n",PCICFG_GET_REG(PCI9056_VPD_DATA));
+}
+
+
+int do_pati(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
+{
+	if (strcmp(argv[1], "info") == 0)
+	{
+		show_pld_regs();
+	 	return 0;
+	}
+	if (strcmp(argv[1], "pci") == 0)
+	{
+		display_pci_regs();
+	 	return 0;
+	}
+	if (strcmp(argv[1], "led") == 0)
+	{
+		int led_nr,led_on;
+		led_nr = (int)simple_strtoul(argv[2], NULL, 10);
+		led_on = (int)simple_strtoul(argv[3], NULL, 10);
+		if(!led_nr)
+			user_led0(led_on);
+		else
+			user_led1(led_on);
+		return 0;
+   	}
+#if defined(CFG_PCI_CON_DEVICE)
+	if (strcmp(argv[1], "con") == 0) {
+		pci_con_connect();
+		return 0;
+	}
+	if (strcmp(argv[1], "disc") == 0) {
+		pci_con_disc();
+		return 0;
+	}
+#endif
+	if (strcmp(argv[1], "eeprom") == 0) {
+		unsigned long addr;
+		int size, offset;
+		offset = 0;
+		size = PATI_EEPROM_LAST_OFFSET;
+		if(argc>2) {
+			if(argc>3) {
+				addr = simple_strtoul(argv[3], NULL, 16);
+				if(argc>4)
+					offset = (int) simple_strtoul(argv[4], NULL, 16);
+				if(argc>5)
+					size = (int) simple_strtoul(argv[5], NULL, 16);
+				if (strcmp(argv[2], "read") == 0) {
+					return (pati_pci_eeprom_read(offset, addr, size));
+				}
+				if (strcmp(argv[2], "write") == 0) {
+					return (pati_pci_eeprom_write(offset, addr, size));
+				}
+			}
+			if (strcmp(argv[2], "prg") == 0) {
+				return (pati_pci_eeprom_prg());
+			}
+			if (strcmp(argv[2], "era") == 0) {
+				return (pati_pci_eeprom_erase());
+			}
+			if (strcmp(argv[2], "reload") == 0) {
+				reload_pci_eeprom();
+				return 0;
+			}
+
+
+		}
+	}
+
+	return (do_mplcommon(cmdtp, flag, argc, argv));
+}
+
+U_BOOT_CMD(
+	pati,	8,	1,	do_pati,
+	"pati    - PATI specific Cmds\n",
+	"info - displays board information\n"
+	"pati pci  - displays PCI registers\n"
+	"pati led <nr> <on> \n"
+	"          - switch LED <nr> <on>\n"
+	"pati flash mem [SrcAddr]\n"
+	"          - updates U-Boot with image in memory\n"
+	"pati eeprom <cmd> - PCI EEPROM sub-system\n"
+	"    read <addr> <offset> <size>\n"
+	"          - read PCI EEPROM to <addr> from <offset> <size> words\n"
+	"    write <addr> <offset> <size>\n"
+	"          - write PCI EEPROM from <addr> to <offset> <size> words\n"
+	"    prg   - programm PCI EEPROM with default values\n"
+	"    era   - erase PCI EEPROM (write all word to 0xffff)\n"
+	"    reload- Reload PCI Bridge with EEPROM Values\n"
+	"    NOTE: <addr> must start on word boundary\n"
+	"          <offset> and <size> must be even byte values\n"
+);
+
+/* ------------------------------------------------------------------------- */
diff --git a/board/mpl/pati/config.mk b/board/mpl/pati/config.mk
new file mode 100644
index 0000000..b8a0985
--- /dev/null
+++ b/board/mpl/pati/config.mk
@@ -0,0 +1,31 @@
+#
+# (C) Copyright 2003
+# Martin Winistoerfer, martinwinistoerfer@gmx.ch.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+#
+# EPQ Board Configuration
+#
+
+# Boot from flash at location 0x00000000
+TEXT_BASE = 0xFFF00000
+
+PLATFORM_CPPFLAGS += -DTEXT_BASE=$(TEXT_BASE) -I$(TOPDIR)
diff --git a/board/mpl/pati/pati.c b/board/mpl/pati/pati.c
new file mode 100644
index 0000000..0355b65
--- /dev/null
+++ b/board/mpl/pati/pati.c
@@ -0,0 +1,618 @@
+/*
+ * (C) Copyright 2003
+ * Martin Winistoerfer, martinwinistoerfer@gmx.ch.
+ * Atapted for PATI
+ * Denis Peter, d.peter@mpl.ch
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/***********************************************************************************
+ * Bits for the SDRAM controller
+ * -----------------------------
+ *
+ * CAL:	CAS Latency. If cleared to 0 (default) the SDRAM controller asserts TA# on
+ *	the 2nd Clock after ACTIVE command (CAS Latency = 2). If set to 1 the SDRAM
+ *	controller asserts TA# on the 3rd Clock after ACTIVE command (CAS Latency = 3).
+ * RCD:	RCD ACTIVE to READ or WRITE Delay (Ras to Cas Delay). If cleared 0 (default)
+ *	tRCD of the SDRAM must equal or less 25ns. If set to 1 tRCD must be equal or less 50ns.
+ * WREC:Write Recovery. If cleared 0 (default) tWR of the SDRAM must equal or less 25ns.
+ *	If set to 1 tWR must be equal or less 50ns.
+ * RP:	Precharge Command Time. If cleared 0 (default) tRP of the SDRAM must equal or less
+ *	25ns. If set to 1 tRP must be equal or less 50ns.
+ * RC:	Auto Refresh to Active Time. If cleared 0 (default) tRC of the SDRAM must equal
+ *	or less 75ns. If set to 1 tRC must be equal or less 100ns.
+ * LMR:	Bit to set the Mode Register of the SDRAM. If set, the next access to the SDRAM
+ *	is the Load Mode Register Command.
+ * IIP:	Init in progress. Set to 1 for starting the init sequence
+ *	(Precharge All). As long this bit is set, the Precharge All is still in progress.
+ *	After command has completed, wait at least for 8 refresh (200usec) before proceed.
+ **********************************************************************************/
+
+#include <common.h>
+#include <mpc5xx.h>
+#include <devices.h>
+#include <pci_ids.h>
+#define PLX9056_LOC
+#include "plx9056.h"
+#include "pati.h"
+
+#if defined(__APPLE__)
+/* Leading underscore on symbols */
+#  define SYM_CHAR "_"
+#else /* No leading character on symbols */
+#  define SYM_CHAR
+#endif
+
+#undef SDRAM_DEBUG
+/*
+ * Macros to generate global absolutes.
+ */
+#define GEN_SYMNAME(str) SYM_CHAR #str
+#define GEN_VALUE(str) #str
+#define GEN_ABS(name, value) \
+		asm (".globl " GEN_SYMNAME(name)); \
+		asm (GEN_SYMNAME(name) " = " GEN_VALUE(value))
+
+
+/************************************************************************
+ * Early debug routines
+ */
+void write_hex (unsigned char i)
+{
+	char cc;
+
+	cc = i >> 4;
+	cc &= 0xf;
+	if (cc > 9)
+		serial_putc (cc + 55);
+	else
+		serial_putc (cc + 48);
+	cc = i & 0xf;
+	if (cc > 9)
+		serial_putc (cc + 55);
+	else
+		serial_putc (cc + 48);
+}
+
+#if defined(SDRAM_DEBUG)
+
+void write_4hex (unsigned long val)
+{
+	write_hex ((unsigned char) (val >> 24));
+	write_hex ((unsigned char) (val >> 16));
+	write_hex ((unsigned char) (val >> 8));
+	write_hex ((unsigned char) val);
+}
+
+#endif
+
+unsigned long in32(unsigned long addr)
+{
+	unsigned long *p=(unsigned long *)addr;
+	return *p;
+}
+
+void out32(unsigned long addr,unsigned long data)
+{
+	unsigned long *p=(unsigned long *)addr;
+	*p=data;
+}
+
+typedef struct {
+	unsigned short boardtype; /* Board revision and Population Options */
+	unsigned char cal;		/* cas Latency  0:CAL=2 1:CAL=3 */
+	unsigned char rcd;		/* ras to cas delay  0:<25ns 1:<50ns*/
+	unsigned char wrec;		/* write recovery 0:<25ns 1:<50ns */
+	unsigned char pr;		/* Precharge Command Time 0:<25ns 1:<50ns */
+	unsigned char rc;		/* Auto Refresh to Active Time 0:<75ns 1:<100ns */
+	unsigned char sz;		/* log binary => Size = (4MByte<<sz) 5 = 128, 4 = 64, 3 = 32, 2 = 16, 1=8 */
+} sdram_t;
+
+const sdram_t sdram_table[] = {
+	{ 0x0000,	/* PATI Rev A, 16MByte -1 Board */
+		1,	/* Case Latenty = 3 */
+		0,	/* ras to cas delay  0 (20ns) */
+		0,	/* write recovery 0:<25ns 1:<50ns*/
+		0,	/* Precharge Command Time 0 (20ns) */
+		0,	/* Auto Refresh to Active Time 0 (68) */
+		2	/* log binary => Size 2 = 16MByte, 1=8 */
+	},
+	{ 0xffff, /* terminator */
+	  0xff,
+	  0xff,
+	  0xff,
+	  0xff,
+	  0xff,
+	  0xff }
+};
+
+
+extern int mem_test (unsigned long start, unsigned long ramsize, int quiet);
+extern void mem_test_reloc(void);
+
+/*
+ * Get RAM size.
+ */
+long int initdram(int board_type)
+{
+	unsigned char board_rev;
+	unsigned long reg;
+	unsigned long lmr;
+	int i,timeout;
+
+#if defined(SDRAM_DEBUG)
+	reg=in32(PLD_CONFIG_BASE+PLD_PART_ID);
+	puts("\n\nSYSTEM part 0x"); write_4hex(SYSCNTR_PART(reg));
+	puts(" Vers 0x"); write_4hex(SYSCNTR_ID(reg));
+	puts("\nSDRAM  part  0x"); write_4hex(SDRAM_PART(reg));
+	puts(" Vers 0x"); write_4hex(SDRAM_ID(reg));
+	reg=in32(PLD_CONFIG_BASE+PLD_BOARD_TIMING);
+	puts("\nBoard rev.   0x"); write_4hex(SYSCNTR_BREV(reg));
+   putc('\n');
+#endif
+	reg=in32(PLD_CONFIG_BASE+PLD_BOARD_TIMING);
+	board_rev=(unsigned char)(SYSCNTR_BREV(reg));
+	i=0;
+	while(1) {
+		if(sdram_table[i].boardtype==0xffff) {
+			puts("ERROR, found no table for Board 0x");
+			write_hex(board_rev);
+			while(1);
+		}
+		if(sdram_table[i].boardtype==(unsigned char)board_rev)
+			break;
+		i++;
+	}
+	/* Set CAL, RCD, WREQ, PR and RC Bits */
+#if defined(SDRAM_DEBUG)
+	puts("Set CAL, RCD, WREQ, PR and RC Bits\n");
+#endif
+	/* mask bits */
+	reg &= ~(SET_REG_BIT(1,SDRAM_CAL) | SET_REG_BIT(1,SDRAM_RCD) | SET_REG_BIT(1,SDRAM_WREQ) |
+				SET_REG_BIT(1,SDRAM_PR)  |  SET_REG_BIT(1,SDRAM_RC) | SET_REG_BIT(1,SDRAM_LMR)  |
+				SET_REG_BIT(1,SDRAM_IIP) | SET_REG_BIT(1,SDRAM_RES0));
+	/* set bits */
+	reg |= (SET_REG_BIT(sdram_table[i].cal,SDRAM_CAL) |
+			  SET_REG_BIT(sdram_table[i].rcd,SDRAM_RCD) |
+			  SET_REG_BIT(sdram_table[i].wrec,SDRAM_WREQ) |
+			  SET_REG_BIT(sdram_table[i].pr,SDRAM_PR) |
+			  SET_REG_BIT(sdram_table[i].rc,SDRAM_RC));
+
+	out32(PLD_CONFIG_BASE+PLD_BOARD_TIMING,reg);
+	/* step 2 set IIP */
+#if defined(SDRAM_DEBUG)
+	puts("step 2 set IIP\n");
+#endif
+	/* step 2 set IIP */
+	reg |= SET_REG_BIT(1,SDRAM_IIP);
+	timeout=0;
+	while (timeout!=0xffff) {
+		__asm__ volatile("eieio");
+		reg=in32(PLD_CONFIG_BASE+PLD_BOARD_TIMING);
+		if((reg & SET_REG_BIT(1,SDRAM_IIP))==0)
+			break;
+		timeout++;
+		udelay(1);
+	}
+	/* wait for at least 8 refresh */
+	udelay(1000);
+	/* set LMR */
+	reg |= SET_REG_BIT(1,SDRAM_LMR);
+	out32(PLD_CONFIG_BASE+PLD_BOARD_TIMING,reg);
+	__asm__ volatile("eieio");
+	lmr=0x00000002; /* sequential burst 4 data */
+	if(sdram_table[i].cal==1)
+		lmr|=0x00000030; /* cal = 3 */
+	else
+		lmr|=0000000020; /* cal = 2 */
+	/* rest standard operation programmed write burst length */
+	/* we have a x32 bit bus to the SDRAM, so shift the addr with 2 */
+	lmr<<=2;
+	in32(CFG_SDRAM_BASE + lmr);
+	/* ok, we're done, return SDRAM size */
+	return ((0x400000 << sdram_table[i].sz));		/* log2 value of 4MByte  */
+}
+
+
+void set_flash_vpp(int ext_vpp, int ext_wp, int int_vpp)
+{
+	unsigned long reg;
+	reg=in32(PLD_CONF_REG2+PLD_CONFIG_BASE);
+	reg &= ~(SET_REG_BIT(1,SYSCNTR_CPU_VPP) |
+			   SET_REG_BIT(1,SYSCNTR_FL_VPP) |
+				SET_REG_BIT(1,SYSCNTR_FL_WP));
+
+	reg |= (SET_REG_BIT(int_vpp,SYSCNTR_CPU_VPP) |
+			   SET_REG_BIT(ext_vpp,SYSCNTR_FL_VPP) |
+				SET_REG_BIT(ext_wp,SYSCNTR_FL_WP));
+	out32(PLD_CONF_REG2+PLD_CONFIG_BASE,reg);
+	udelay(100);
+}
+
+
+void show_pld_regs(void)
+{
+	unsigned long reg,reg1;
+	reg=in32(PLD_CONFIG_BASE+PLD_PART_ID);
+	printf("\nSYSTEM part %ld, Vers %ld\n",SYSCNTR_PART(reg),SYSCNTR_ID(reg));
+	printf("SDRAM  part %ld, Vers %ld\n",SDRAM_PART(reg),SDRAM_ID(reg));
+	reg=in32(PLD_CONFIG_BASE+PLD_BOARD_TIMING);
+	printf("Board rev.  %c\n",(char) (SYSCNTR_BREV(reg)+'A'));
+	printf("Waitstates  %ld\n",GET_SYSCNTR_FLWAIT(reg));
+	printf("SDRAM:      CAL=%ld RCD=%ld WREQ=%ld PR=%ld\n            RC=%ld  LMR=%ld IIP=%ld\n",
+		GET_REG_BIT(reg,SDRAM_CAL),GET_REG_BIT(reg,SDRAM_RCD),
+		GET_REG_BIT(reg,SDRAM_WREQ),GET_REG_BIT(reg,SDRAM_PR),
+		GET_REG_BIT(reg,SDRAM_RC),GET_REG_BIT(reg,SDRAM_LMR),
+		GET_REG_BIT(reg,SDRAM_IIP));
+	reg=in32(PLD_CONFIG_BASE+PLD_CONF_REG1);
+	reg1=in32(PLD_CONFIG_BASE+PLD_CONF_REG2);
+	printf("HW Config:  FLAG=%ld IP=%ld  index=%ld PRPM=%ld\n            ICW=%ld  ISB=%ld BDIS=%ld  PCIM=%ld\n",
+		GET_REG_BIT(reg,SYSCNTR_FLAG),GET_REG_BIT(reg,SYSCNTR_IP),
+		GET_SYSCNTR_BOOTIND(reg),GET_REG_BIT(reg,SYSCNTR_PRM),
+		GET_REG_BIT(reg,SYSCNTR_ICW),GET_SYSCNTR_ISB(reg),
+		GET_REG_BIT(reg1,SYSCNTR_BDIS),GET_REG_BIT(reg1,SYSCNTR_PCIM));
+	printf("Switches:   MUX=%ld PCI_DIS=%ld Boot_EN=%ld  Config=%ld\n",GET_SDRAM_MUX(reg),
+		GET_REG_BIT(reg,SDRAM_PDIS),GET_REG_BIT(reg1,SYSCNTR_BOOTEN),
+		GET_SYSCNTR_CFG(reg1));
+	printf("Misc:       RIP=%ld CPU_VPP=%ld FLSH_VPP=%ld FLSH_WP=%ld\n\n",
+		GET_REG_BIT(reg,SDRAM_RIP),GET_REG_BIT(reg1,SYSCNTR_CPU_VPP),
+		GET_REG_BIT(reg1,SYSCNTR_FL_VPP),GET_REG_BIT(reg1,SYSCNTR_FL_WP));
+}
+
+
+/****************************************************************
+ * Setting IOs
+ * -----------
+ * GPIO6 is User LED1
+ * GPIO7 is Interrupt PLX (Output)
+ * GPIO5 is User LED0
+ * GPIO2 is PLX USERi (Output)
+ * GPIO1 is PLX Interrupt (Input)
+ ****************************************************************/
+ void init_ios(void)
+ {
+	volatile immap_t * immr = (immap_t *) CFG_IMMR;
+	volatile sysconf5xx_t *sysconf = &immr->im_siu_conf;
+	unsigned long reg;
+	reg=sysconf->sc_sgpiocr; /* Data direction register */
+	reg &= ~0x67000000;
+	reg |= 0x27000000; /* set outpupts */
+	sysconf->sc_sgpiocr=reg; /* Data direction register */
+	reg=sysconf->sc_sgpiodt2; /* Data register */
+	/* set output to 0 */
+	reg &= ~0x27000000;
+	/* set IRQ and USERi to 1 */
+	reg |= 0x28000000;
+	sysconf->sc_sgpiodt2=reg; /* Data register */
+}
+
+void user_led0(int led_on)
+{
+	volatile immap_t * immr = (immap_t *) CFG_IMMR;
+	volatile sysconf5xx_t *sysconf = &immr->im_siu_conf;
+	unsigned long reg;
+	reg=sysconf->sc_sgpiodt2; /* Data register */
+	if(led_on)	/* set output to 1 */
+		reg |= 0x04000000;
+	else
+		reg &= ~0x04000000;
+	sysconf->sc_sgpiodt2=reg; /* Data register */
+}
+
+void user_led1(int led_on)
+{
+	volatile immap_t * immr = (immap_t *) CFG_IMMR;
+	volatile sysconf5xx_t *sysconf = &immr->im_siu_conf;
+	unsigned long reg;
+	reg=sysconf->sc_sgpiodt2; /* Data register */
+	if(led_on)	/* set output to 1 */
+		reg |= 0x02000000;
+	else
+		reg &= ~0x02000000;
+	sysconf->sc_sgpiodt2=reg; /* Data register */
+}
+
+
+/****************************************************************
+ * Last Stage Init
+ ****************************************************************/
+int last_stage_init (void)
+{
+	mem_test_reloc();
+	init_ios();
+	return 0;
+}
+
+/****************************************************************
+ * Check the board
+ ****************************************************************/
+
+#define BOARD_NAME	"PATI"
+
+int checkboard (void)
+{
+	unsigned char s[50];
+	unsigned long reg;
+	char rev;
+	int i;
+
+	puts ("\nBoard: ");
+	reg=in32(PLD_CONFIG_BASE+PLD_BOARD_TIMING);
+	rev=(char)(SYSCNTR_BREV(reg)+'A');
+	i = getenv_r ("serial#", s, 32);
+	if ((i == -1)) {
+		puts ("### No HW ID - assuming " BOARD_NAME);
+		printf(" Rev. %c\n",rev);
+	}
+	else {
+		s[sizeof(BOARD_NAME)-1] = 0;
+		printf ("%s-1 Rev %c SN: %s\n", s,rev,
+				&s[sizeof(BOARD_NAME)]);
+	}
+	set_flash_vpp(1,0,0); /* set Flash VPP */
+	return 0;
+}
+
+
+#ifdef CFG_PCI_CON_DEVICE
+/************************************************************************
+ * PCI Communication
+ *
+ * Alive (Pinging):
+ * ----------------
+ * PCI Host sends message ALIVE, Local acknowledges with ALIVE
+ *
+ * PCI_CON console over PCI:
+ * -------------------------
+ * Local side:
+ *     - uses PCI9056_LOC_TO_PCI_DBELL register to signal that
+ *       data is avaible (PCIMSG_CONN)
+ *     - uses PCI9056_MAILBOX1 to send data
+ *     - uses PCI9056_MAILBOX0 to receive data
+ * PCI side:
+ *     - uses PCI9056_PCI_TO_LOC_DBELL register to signal that
+ *       data is avaible (PCIMSG_CONN)
+ *     - uses PCI9056_MAILBOX0 to send data
+ *     - uses PCI9056_MAILBOX1 to receive data
+ *
+ * How it works:
+ *     Send:
+ *     - check if PCICON_TRANSMIT_REG is empty
+ *     - write data or'ed with 0x80000000 into the PCICON_TRANSMIT_REG
+ *     - write PCIMSG_CONN into the PCICON_DBELL_REG to signal a data
+ *       is waiting
+ *     Receive:
+ *     - get an interrupt via the PCICON_ACK_REG register message
+ *       PCIMSG_CONN
+ *     - write the data from the PCICON_RECEIVE_REG into the receive
+ *       buffer and if the receive buffer is not full, clear the
+ *       PCICON_RECEIVE_REG (this allows the counterpart to write more data)
+ *     - Clear the interrupt by writing 0xFFFFFFFF to the PCICON_ACK_REG
+ *
+ *     The PCICON_RECEIVE_REG must be cleared by the routine which reads
+ *     the receive buffer if the buffer is not full any more
+ *
+ */
+
+#undef PCI_CON_DEBUG
+
+#ifdef	PCI_CON_DEBUG
+#define	PCI_CON_PRINTF(fmt,args...)	serial_printf (fmt ,##args)
+#else
+#define PCI_CON_PRINTF(fmt,args...)
+#endif
+
+
+/*********************************************************
+ * we work only with a receive buffer on eiter side.
+ * Transmit buffer is free, if mailbox is cleared.
+ * Transmit character is or'ed with 0x80000000
+ * PATI receive register MAILBOX0
+ * PATI transmit register MAILBOX1
+ *********************************************************/
+#define PCICON_RECEIVE_REG	PCI9056_MAILBOX0
+#define PCICON_TRANSMIT_REG	PCI9056_MAILBOX1
+#define PCICON_DBELL_REG	PCI9056_LOC_TO_PCI_DBELL
+#define PCICON_ACK_REG		PCI9056_PCI_TO_LOC_DBELL
+
+
+#define PCIMSG_ALIVE		0x1
+#define PCIMSG_CONN		0x2
+#define PCIMSG_DISC		0x3
+#define PCIMSG_CON_DATA	0x5
+
+
+#define PCICON_GET_REG(x)	(in32(x + PCI_CONFIG_BASE))
+#define PCICON_SET_REG(x,y)	(out32(x + PCI_CONFIG_BASE,y))
+#define PCICON_TX_FLAG		0x80000000
+
+
+#define REC_BUFFER_SIZE	0x100
+int recbuf[REC_BUFFER_SIZE];
+static int r_ptr = 0;
+int w_ptr;
+device_t pci_con_dev;
+int conn=0;
+int buff_full=0;
+
+void pci_con_put_it(const char c)
+{
+	/* Test for completition */
+	unsigned long reg;
+	do {
+		reg=PCICON_GET_REG(PCICON_TRANSMIT_REG);
+	}while(reg);
+	reg=PCICON_TX_FLAG + c;
+	PCICON_SET_REG(PCICON_TRANSMIT_REG,reg);
+	PCICON_SET_REG(PCICON_DBELL_REG,PCIMSG_CON_DATA);
+}
+
+void pci_con_putc(const char c)
+{
+	pci_con_put_it(c);
+	if(c == '\n')
+		pci_con_put_it('\r');
+}
+
+
+int pci_con_getc(void)
+{
+	int res;
+	int diff;
+	while(r_ptr==(volatile int)w_ptr);
+	res=recbuf[r_ptr++];
+	if(r_ptr==REC_BUFFER_SIZE)
+		r_ptr=0;
+	if(w_ptr<r_ptr)
+		diff=r_ptr+REC_BUFFER_SIZE-w_ptr;
+	else
+		diff=r_ptr-w_ptr;
+	if((diff<(REC_BUFFER_SIZE-4)) && buff_full) {
+   		/* clear Mail box */
+			buff_full=0;
+			PCICON_SET_REG(PCICON_RECEIVE_REG,0L);
+	}
+	return res;
+}
+
+int pci_con_tstc(void)
+{
+	if(r_ptr==(volatile int)w_ptr)
+		return 0;
+	return 1;
+}
+
+void pci_con_puts (const char *s)
+{
+	while (*s) {
+		pci_con_putc(*s);
+		++s;
+	}
+}
+
+void pci_con_init (void)
+{
+	w_ptr = 0;
+	r_ptr = 0;
+	PCICON_SET_REG(PCICON_RECEIVE_REG,0L);
+	conn=1;
+}
+
+/*******************************************
+ * IRQ routine
+ ******************************************/
+int pci_dorbell_irq(void)
+{
+	unsigned long reg,data;
+	int diff;
+	reg=PCICON_GET_REG(PCI9056_INT_CTRL_STAT);
+	PCI_CON_PRINTF(" PCI9056_INT_CTRL_STAT = %08lX\n",reg);
+	if(reg & (1<<20) ) {
+		/* read doorbell */
+		reg=PCICON_GET_REG(PCICON_ACK_REG);
+		switch(reg) {
+			case PCIMSG_ALIVE:
+				PCI_CON_PRINTF(" Alive\n");
+				PCICON_SET_REG(PCICON_DBELL_REG,PCIMSG_ALIVE);
+				break;
+			case PCIMSG_CONN:
+				PCI_CON_PRINTF(" Conn %d",conn);
+				w_ptr = 0;
+				r_ptr = 0;
+				buff_full=0;
+				PCICON_SET_REG(PCICON_RECEIVE_REG,0L);
+				conn=1;
+				PCI_CON_PRINTF(" ... %d\n",conn);
+				break;
+			case PCIMSG_CON_DATA:
+				data=PCICON_GET_REG(PCICON_RECEIVE_REG);
+				recbuf[w_ptr++]=(int)(data&0xff);
+				PCI_CON_PRINTF(" Data Console %lX, %X %d %d %X\n",data,((int)(data&0xFF)),
+					r_ptr,w_ptr,recbuf[w_ptr-1]);
+				if(w_ptr==REC_BUFFER_SIZE)
+					w_ptr=0;
+				if(w_ptr<r_ptr)
+					diff=r_ptr+REC_BUFFER_SIZE-w_ptr;
+				else
+					diff=r_ptr-w_ptr;
+				if(diff>(REC_BUFFER_SIZE-4))
+					buff_full=1;
+				else
+					/* clear Mail box */
+					PCICON_SET_REG(PCICON_RECEIVE_REG,0L);
+				break;
+			default:
+				serial_printf(" PCI9056_PCI_TO_LOC_DBELL = %08lX\n",reg);
+		}
+		/* clear IRQ */
+		PCICON_SET_REG(PCICON_ACK_REG,~0L);
+	}
+	return 0;
+}
+
+void pci_con_connect(void)
+{
+	unsigned long reg;
+	conn=0;
+	reg=PCICON_GET_REG(PCI9056_INT_CTRL_STAT);
+	/* default 0x0f010180 */
+	reg &= 0xff000000;
+	reg |= 0x00030000; /* enable local dorbell */
+	reg |= 0x00000300; /* enable PCI dorbell */
+	PCICON_SET_REG(PCI9056_INT_CTRL_STAT , reg);
+	irq_install_handler (0x2, (interrupt_handler_t *) pci_dorbell_irq,NULL);
+	memset (&pci_con_dev, 0, sizeof (pci_con_dev));
+	strcpy (pci_con_dev.name, "pci_con");
+	pci_con_dev.flags = DEV_FLAGS_OUTPUT | DEV_FLAGS_INPUT | DEV_FLAGS_SYSTEM;
+	pci_con_dev.putc = pci_con_putc;
+	pci_con_dev.puts = pci_con_puts;
+	pci_con_dev.getc = pci_con_getc;
+	pci_con_dev.tstc = pci_con_tstc;
+	device_register (&pci_con_dev);
+	printf("PATI ready for PCI connection, type ctrl-c for exit\n");
+	do {
+		udelay(10);
+		if((volatile int)conn)
+			break;
+		if(ctrlc()) {
+			irq_free_handler(0x2);
+			return;
+		}
+	}while(1);
+	console_assign(stdin,"pci_con");
+	console_assign(stderr,"pci_con");
+	console_assign(stdout,"pci_con");
+}
+
+void pci_con_disc(void)
+{
+	console_assign(stdin,"serial");
+	console_assign(stderr,"serial");
+	console_assign(stdout,"serial");
+	PCICON_SET_REG(PCICON_DBELL_REG,PCIMSG_DISC);
+	/* reconnection */
+	irq_free_handler(0x02);
+	pci_con_connect();
+}
+#endif /* #ifdef CFG_PCI_CON_DEVICE */
+
+/*
+ * Absolute environment address for linker file.
+ */
+GEN_ABS(env_start, CFG_ENV_OFFSET + CFG_FLASH_BASE);
diff --git a/board/mpl/pati/pati.h b/board/mpl/pati/pati.h
new file mode 100644
index 0000000..d521772
--- /dev/null
+++ b/board/mpl/pati/pati.h
@@ -0,0 +1,440 @@
+/*
+ * (C) Copyright 2003
+ * Denis Peter, d.peter@mpl.ch
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+/************************************************************************
+ * MACROS and register definitions for PATI Registers
+ ************************************************************************/
+#ifndef __PATI_H_
+#define __PATI_H_	1
+
+#define PLD_PART_ID		0x0
+#define PLD_BOARD_TIMING	0x4
+#define PLD_CONF_REG1		0x8
+#define PLD_CONF_REG2		0xC
+#define PLD_CONF_RES		0x10
+
+#define SET_REG_BIT(y,x) (y<<(31-x))
+#define GET_REG_BIT(y,x) ((y>>(31-x)) & 0x1L)
+
+/* SDRAM Controller PLD_PART_ID */
+/* 9  10 11 12 13 14 19 31 */
+#define SDRAM_PART3	9
+#define SDRAM_PART2	10
+#define SDRAM_PART1	11
+#define SDRAM_PART0	12
+#define SDRAM_ID3	13
+#define SDRAM_ID2	14
+#define SDRAM_ID1	19
+#define SDRAM_ID0	31
+
+#define SDRAM_PART(x)	(	\
+	(GET_REG_BIT(x,SDRAM_PART3)<<3) |\
+	(GET_REG_BIT(x,SDRAM_PART2)<<2) |\
+	(GET_REG_BIT(x,SDRAM_PART1)<<1) |\
+	(GET_REG_BIT(x,SDRAM_PART0)))
+
+#define SDRAM_ID(x)	(	\
+	(GET_REG_BIT(x,SDRAM_ID3)<<3) |\
+	(GET_REG_BIT(x,SDRAM_ID2)<<2) |\
+	(GET_REG_BIT(x,SDRAM_ID1)<<1) |\
+	(GET_REG_BIT(x,SDRAM_ID0)))
+
+/* System Controller */
+/* 0  1 3 4 5 16 20 28 29 30 */
+#define SYSCNTR_PART4	0
+#define SYSCNTR_PART3	1
+#define SYSCNTR_PART2	3
+#define SYSCNTR_PART1	4
+#define SYSCNTR_PART0	5
+#define SYSCNTR_ID4	16
+#define SYSCNTR_ID3	20
+#define SYSCNTR_ID2	28
+#define SYSCNTR_ID1	29
+#define SYSCNTR_ID0	30
+
+#define SYSCNTR_PART(x)	(	\
+	(GET_REG_BIT(x,SYSCNTR_PART4)<<4) |\
+	(GET_REG_BIT(x,SYSCNTR_PART3)<<3) |\
+	(GET_REG_BIT(x,SYSCNTR_PART2)<<2) |\
+	(GET_REG_BIT(x,SYSCNTR_PART1)<<1) |\
+	(GET_REG_BIT(x,SYSCNTR_PART0)))
+
+#define SYSCNTR_ID(x)	(	\
+	(GET_REG_BIT(x,SYSCNTR_ID4)<<4) |\
+	(GET_REG_BIT(x,SYSCNTR_ID3)<<3) |\
+	(GET_REG_BIT(x,SYSCNTR_ID2)<<2) |\
+	(GET_REG_BIT(x,SYSCNTR_ID1)<<1) |\
+	(GET_REG_BIT(x,SYSCNTR_ID0)))
+
+/* SDRAM Controller PLD_BOARD_TIMING */
+/* 9  10 11 12 13 14 19 31 */
+#define SDRAM_CAL	9
+#define SDRAM_RCD	10
+#define SDRAM_WREQ	11
+#define SDRAM_PR 	12
+#define SDRAM_RC	13
+#define SDRAM_LMR	14
+#define SDRAM_IIP	19
+#define SDRAM_RES0	31
+/* System Controller */
+/* 0  1 3 4 5 16 20 28 29 30 */
+#define SYSCNTR_BREV0	0
+#define SYSCNTR_BREV1	1
+#define SYSCNTR_BREV2	3
+#define SYSCNTR_BREV3	4
+#define SYSCNTR_RES0	5
+#define SYSCNTR_RES1	16
+#define SYSCNTR_RES2	20
+#define SYSCNTR_FLWAIT2	28
+#define SYSCNTR_FLWAIT1	29
+#define SYSCNTR_FLWAIT0	30
+
+#define SYSCNTR_BREV(x)	(	\
+	(GET_REG_BIT(x,SYSCNTR_BREV3)<<3) |\
+	(GET_REG_BIT(x,SYSCNTR_BREV2)<<2) |\
+	(GET_REG_BIT(x,SYSCNTR_BREV1)<<1) |\
+	(GET_REG_BIT(x,SYSCNTR_BREV0)))
+
+#define GET_SYSCNTR_FLWAIT(x)	(	\
+	(GET_REG_BIT(x,SYSCNTR_FLWAIT2)<<2) |\
+	(GET_REG_BIT(x,SYSCNTR_FLWAIT1)<<1) |\
+	(GET_REG_BIT(x,SYSCNTR_FLWAIT0)))
+
+#define SET_SYSCNTR_FLWAIT(x)	(	\
+	(SET_REG_BIT(((x & 0x04)!=0),SYSCNTR_FLWAIT2)) |\
+	(SET_REG_BIT(((x & 0x02)!=0)x,SYSCNTR_FLWAIT1)) |\
+	(SET_REG_BIT(((x & 0x01)!=0)x,SYSCNTR_FLWAIT0)))
+
+/* SDRAM Controller REG 2*/
+/* 9  10 11 12 13 14 19 31 */
+#define SDRAM_MUX0	9
+#define SDRAM_MUX1	10
+#define SDRAM_PDIS	11
+#define SDRAM_RES1 	12
+#define SDRAM_RES2	13
+#define SDRAM_RES3	14
+#define SDRAM_RES4	19
+#define SDRAM_RIP	31
+
+#define GET_SDRAM_MUX(x)	(	\
+	(GET_REG_BIT(x,SDRAM_MUX1)<<1)| \
+	(GET_REG_BIT(x,SDRAM_MUX0)))
+
+
+/* System Controller */
+/* 0  1 3 4 5 16 20 28 29 30 */
+#define SYSCNTR_FLAG	0
+#define SYSCNTR_IP	1
+#define SYSCNTR_BIND2	3
+#define SYSCNTR_BIND1	4
+#define SYSCNTR_BIND0	5
+#define SYSCNTR_PRM	16
+#define SYSCNTR_ICW	20
+#define SYSCNTR_ISB2	28
+#define SYSCNTR_ISB1	29
+#define SYSCNTR_ISB0	30
+
+#define GET_SYSCNTR_BOOTIND(x)	(	\
+	(GET_REG_BIT(x,SYSCNTR_BIND2)<<2) |\
+	(GET_REG_BIT(x,SYSCNTR_BIND1)<<1) |\
+	(GET_REG_BIT(x,SYSCNTR_BIND0)))
+
+#define SET_SYSCNTR_BOOTIND(x)	(	\
+	(SET_REG_BIT(((x & 0x04)!=0),SYSCNTR_BIND2)) |\
+	(SET_REG_BIT(((x & 0x02)!=0)x,SYSCNTR_BIND1))| \
+	(SET_REG_BIT(((x & 0x01)!=0)x,SYSCNTR_BIND0)))
+
+#define GET_SYSCNTR_ISB(x)	(	\
+	(GET_REG_BIT(x,SYSCNTR_ISB2)<<2)| \
+	(GET_REG_BIT(x,SYSCNTR_ISB1)<<1)| \
+	(GET_REG_BIT(x,SYSCNTR_ISB0)))
+
+#define SET_SYSCNTR_ISB(x)	(	\
+	(SET_REG_BIT(((x & 0x04)!=0),SYSCNTR_ISB2))| \
+	(SET_REG_BIT(((x & 0x02)!=0)x,SYSCNTR_ISB))| \
+	(SET_REG_BIT(((x & 0x01)!=0)x,SYSCNTR_ISB0)))
+
+/* SDRAM Controller REG 3*/
+/* 9  10 11 12 13 14 19 31 */
+#define SDRAM_RES5	9
+#define SDRAM_CFG1	10
+#define SDRAM_CFG2	11
+#define SDRAM_CFG3 	12
+#define SDRAM_RES6	13
+#define SDRAM_CFG5	14
+#define SDRAM_CFG6	19
+#define SDRAM_RES7	31
+
+#define GET_SDRAM_CFG(x)	(	\
+	(GET_REG_BIT(x,SDRAM_CFG6)<<4) |\
+	(GET_REG_BIT(x,SDRAM_CFG5)<<3) |\
+	(GET_REG_BIT(x,SDRAM_CFG3)<<2) |\
+	(GET_REG_BIT(x,SDRAM_CFG2)<<1) |\
+	(GET_REG_BIT(x,SDRAM_CFG1)))
+
+/* System Controller */
+/* 0  1 3 4 5 16 20 28 29 30 */
+#define SYSCNTR_BDIS	0
+#define SYSCNTR_PCIM	1
+#define SYSCNTR_CFG0	3
+#define SYSCNTR_CFG1	4
+#define SYSCNTR_CFG2	5
+#define SYSCNTR_CFG3	16
+#define SYSCNTR_BOOTEN	20
+#define SYSCNTR_CPU_VPP	28
+#define SYSCNTR_FL_VPP	29
+#define SYSCNTR_FL_WP	30
+
+#define GET_SYSCNTR_CFG(x)	(	\
+	(GET_REG_BIT(x,SYSCNTR_CFG3)<<3)| \
+	(GET_REG_BIT(x,SYSCNTR_CFG2)<<2)| \
+	(GET_REG_BIT(x,SYSCNTR_CFG1)<<1)| \
+	(GET_REG_BIT(x,SYSCNTR_CFG0)))
+
+
+/***************************************************************
+ * MISC Defines
+ ***************************************************************/
+
+#define PCI_VENDOR_ID_MPL 	0x18E6
+#define PCI_DEVICE_ID_PATI	0x00DA
+
+#if defined(CONFIG_MIP405)
+#define PATI_FIRMWARE_START_OFFSET	0x00300000
+#define PATI_ISO_STRING  "MEV-10084-001"
+#endif
+
+#define PATI_ENDIAN_MODE	0x3E
+
+/*******************************************
+ * PATI Mapping:
+ * -------------
+ * PCI Map:
+ * -------
+ * All addreses are mapped into the memory area
+ * (IO Area on some areas may also be possible)
+ * - pci_cfg_mem_base: fixed address to the PLX config area size 512Bytes
+ * - pci_space0_addr:  configurable
+ * - pci_space1_addr	  configurable
+ *
+ * Local Map:
+ * ----------
+ * Local addresses (Remap)
+ * - SDRAM      0x06000000 Size 16MByte mask 0xff000000
+ * - EPLD CFG   0x07000000 Size 512Bytes
+ * - FLASH      0x03000000 Size up to 8MByte
+ * - CPU        0x01000000 Size 4MByte (only accessable if special configured)
+ *
+ * Implemention:
+ * -------------
+ * To prevent using large resources reservation on the host following
+ * PCI mapping is choosed:
+ * - pci_cfg_mem_base: fixed address to the PLX config area size 512Bytes
+ * - pci_space0_addr:  configured to the EPLD Config Area size 256Bytes
+ * - pci_space1_addr:  configured to the SDRAM Area size 1MBytes, this
+ *                     space is used to switch between SDRAM, Flash and CPU
+ *
+ */
+
+/* Attribute definitions */
+#define PATI_BUS_SIZE_8		0
+#define PATI_BUS_SIZE_16	1
+#define PATI_BUS_SIZE_32	3
+
+#define PATI_SPACE0_MASK	(0xFEFFFE00)  /* Mask Attributes */
+#define PATI_SPACE1_MASK	(0x00000000)  /* Mask Attributes */
+
+#define PATI_EXTRA_LONG_EEPROM	1
+
+#define SPACE0_TA_ENABLE (1<<6)
+#define SPACE1_TA_ENABLE (1<<6)
+
+/* Config Area */
+#define PATI_LOC_CFG_ADDR		0x07000000		/* Local Address */
+#define PATI_LOC_CFG_MASK		0xFFFFFF00  		/* 256 Bytes */
+/* Attributes */
+#define PATI_LOC_CFG_BUS_SIZE		PATI_BUS_SIZE_32  	/* 32 Bit */
+#define PATI_LOC_CFG_BURST		0  			/* No Burst */
+#define PATI_LOC_CFG_NO_PREFETCH	1  			/* No Prefetch */
+#define PATI_LOC_CFG_TA_ENABLE		1 			/* Enable TA */
+
+#define PATI_LOC_CFG_SPACE0_ATTR  ( \
+		PATI_LOC_CFG_BUS_SIZE | \
+		(PATI_LOC_CFG_TA_ENABLE << 6) | \
+		(PATI_LOC_CFG_NO_PREFETCH << 8) | \
+		(PATI_LOC_CFG_BURST << 24) | \
+		(PATI_EXTRA_LONG_EEPROM << 25))
+
+/* should never be used */
+#define PATI_LOC_CFG_SPACE1_ATTR  ( \
+		PATI_LOC_CFG_BUS_SIZE | \
+		(PATI_LOC_CFG_TA_ENABLE << 6) | \
+		(PATI_LOC_CFG_NO_PREFETCH << 9) | \
+		(PATI_LOC_CFG_BURST << 8))
+
+
+/* SDRAM Area */
+#define PATI_LOC_SDRAM_ADDR		0x06000000		/* Local Address */
+#define PATI_LOC_SDRAM_MASK		0xFFF00000		/* 1MByte */
+/* Attributes */
+#define PATI_LOC_SDRAM_BUS_SIZE		PATI_BUS_SIZE_32  	/* 32 Bit */
+#define PATI_LOC_SDRAM_BURST		0  			/* No Burst */
+#define PATI_LOC_SDRAM_NO_PREFETCH	0  			/* Prefetch */
+#define PATI_LOC_SDRAM_TA_ENABLE	1  			/* Enable TA */
+
+/* should never be used */
+#define PATI_LOC_SDRAM_SPACE0_ATTR  ( \
+		PATI_LOC_SDRAM_BUS_SIZE | \
+		(PATI_LOC_SDRAM_TA_ENABLE << 6) | \
+		(PATI_LOC_SDRAM_NO_PREFETCH << 8) | \
+		(PATI_LOC_SDRAM_BURST << 24) | \
+		(PATI_EXTRA_LONG_EEPROM << 25))
+
+#define PATI_LOC_SDRAM_SPACE1_ATTR  ( \
+		PATI_LOC_SDRAM_BUS_SIZE | \
+		(PATI_LOC_SDRAM_TA_ENABLE << 6) | \
+		(PATI_LOC_SDRAM_NO_PREFETCH << 9) | \
+		(PATI_LOC_SDRAM_BURST << 8))
+
+
+/* Flash Area */
+#define PATI_LOC_FLASH_ADDR		0x03000000		/* Local Address */
+#define PATI_LOC_FLASH_MASK		0xFFF00000		/* 1MByte */
+/* Attributes */
+#define PATI_LOC_FLASH_BUS_SIZE		PATI_BUS_SIZE_16  	/* 16 Bit */
+#define PATI_LOC_FLASH_BURST		0  			/* No Burst */
+#define PATI_LOC_FLASH_NO_PREFETCH	1  			/* No Prefetch */
+#define PATI_LOC_FLASH_TA_ENABLE	1  			/* Enable TA */
+
+/* should never be used */
+#define PATI_LOC_FLASH_SPACE0_ATTR  ( \
+		PATI_LOC_FLASH_BUS_SIZE | \
+		(PATI_LOC_FLASH_TA_ENABLE << 6) | \
+		(PATI_LOC_FLASH_NO_PREFETCH << 8) | \
+		(PATI_LOC_FLASH_BURST << 24) | \
+		(PATI_EXTRA_LONG_EEPROM << 25))
+
+#define PATI_LOC_FLASH_SPACE1_ATTR  ( \
+		PATI_LOC_FLASH_BUS_SIZE | \
+		(PATI_LOC_FLASH_TA_ENABLE << 6) | \
+		(PATI_LOC_FLASH_NO_PREFETCH << 9) | \
+		(PATI_LOC_FLASH_BURST << 8))
+
+
+/* CPU Area */
+#define PATI_LOC_CPU_ADDR		0x01000000		/* Local Address */
+#define PATI_LOC_CPU_MASK		0xFFF00000		/* 1Mbyte */
+/* Attributes */
+#define PATI_LOC_CPU_BUS_SIZE		PATI_BUS_SIZE_32  	/* 32 Bit */
+#define PATI_LOC_CPU_BURST		0			/* No Burst */
+#define PATI_LOC_CPU_NO_PREFETCH	1			/* No Prefetch */
+#define PATI_LOC_CPU_TA_ENABLE		1			/* Enable TA */
+
+/* should never be used */
+#define PATI_LOC_CPU_SPACE0_ATTR  ( \
+		PATI_LOC_CPU_BUS_SIZE | \
+		(PATI_LOC_CPU_TA_ENABLE << 6) | \
+		(PATI_LOC_CPU_NO_PREFETCH << 8) | \
+		(PATI_LOC_CPU_BURST << 24) | \
+		(PATI_EXTRA_CPU_EEPROM << 25))
+
+#define PATI_LOC_CPU_SPACE1_ATTR  ( \
+		PATI_LOC_CPU_BUS_SIZE | \
+		(PATI_LOC_CPU_TA_ENABLE << 6) | \
+		(PATI_LOC_CPU_NO_PREFETCH << 9) | \
+		(PATI_LOC_CPU_BURST << 8))
+
+/***************************************************
+ * Hardware Config word definition
+ ***************************************************/
+#define BOOT_EXT_FLASH		0x00000000
+#define BOOT_INT_FLASH		0x00000004
+#define BOOT_FROM_PCI		0x00000006
+#define BOOT_FROM_SDRAM		0x00000005
+
+#define ENABLE_INT_ARB		0x00000008
+
+#define INITIAL_IRQ_PREF	0x00000010
+
+#define INITIAL_MEM_0M		0x00000000
+#define INITIAL_MEM_4M		0x00000080
+#define INITIAL_MEM_8M		0x00000040
+#define INITIAL_MEM_12M		0x000000C0
+#define INITIAL_MEM_16M		0x00000020
+#define INITIAL_MEM_20M		0x000000A0
+#define INITIAL_MEM_24M		0x00000060
+#define INITIAL_MEM_28M		0x000000E0
+/* CONF */
+#define INTERNAL_HWCONF		0x00000100
+/* PRPM */
+#define LOCAL_CPU_SLAVE		0x00000200
+/* BDIS */
+#define DISABLE_MEM_CNTR	0x00000400
+/* PCIM */
+#define PCI_MASTER_ONLY		0x00000800
+
+
+#define PATI_HW_START		((BOOT_EXT_FLASH | INITIAL_MEM_28M | INITIAL_IRQ_PREF))
+#define PATI_HW_PCI_ONLY 	((BOOT_EXT_FLASH | INITIAL_MEM_28M | INITIAL_IRQ_PREF | PCI_MASTER_ONLY))
+#define PATI_HW_CPU_ACC		((BOOT_EXT_FLASH | INITIAL_MEM_12M | INITIAL_IRQ_PREF | PCI_MASTER_ONLY))
+#define PATI_HW_CPU_SLAVE 	((BOOT_EXT_FLASH | INITIAL_MEM_12M | INITIAL_IRQ_PREF | PCI_MASTER_ONLY | LOCAL_CPU_SLAVE))
+
+/***************************************************
+ * Direct Master Config
+ ***************************************************/
+#define PATI_DMASTER_PCI_ADDR		0x01000000
+#define PATI_BUS_MASTER 1
+
+
+#define PATI_DMASTER_MASK 		0xFFF00000  /* 1MByte */
+#define PATI_DMASTER_ADDR 		0x01000000  /* Local Address */
+
+#define PATI_DMASTER_MEMORY_EN 		0x00000001 /* 0x00000001 */
+#define PATI_DMASTER_READ_AHEAD 	0x00000004 /* 0x00000004 */
+#define PATI_DMASTER_READ_NOT_AHEAD 	0x00000000 /* 0x00000004 */
+#define PATI_DMASTER_PRE_SIZE_CNTRL_0	0x00000000
+#define PATI_DMASTER_PRE_SIZE_CNTRL_4	0x00000008
+#define PATI_DMASTER_PRE_SIZE_CNTRL_8	0x00001000
+#define PATI_DMASTER_PRE_SIZE_CNTRL_16	0x00001008
+#define PATI_DMASTER_REL_PCI		0x00000000
+#define PATI_DMASTER_NOT_REL_PCI	0x00000010
+#define PATI_DMASTER_WR_INVAL		0x00000200
+#define PATI_DMASTER_NOT_WR_INVAL	0x00000000
+#define PATI_DMASTER_PRE_LIMIT		0x00000800
+#define PATI_DMASTER_PRE_CONT		0x00000000
+#define PATI_DMASTER_DELAY_WR_0		0x00000000
+#define PATI_DMASTER_DELAY_WR_4		0x00004000
+#define PATI_DMASTER_DELAY_WR_8		0x00008000
+#define PATI_DMASTER_DELAY_WR_16	0x0000C000
+
+#define PATI_DMASTER_PCI_ADDR_MASK	0xFFFF0000
+
+#define PATI_DMASTER_ATTR	\
+	PATI_DMASTER_MEMORY_EN | \
+	PATI_DMASTER_READ_AHEAD | \
+	PATI_DMASTER_PRE_SIZE_CNTRL_4 | \
+	PATI_DMASTER_REL_PCI | \
+	PATI_DMASTER_NOT_WR_INVAL | \
+	PATI_DMASTER_PRE_LIMIT | \
+	PATI_DMASTER_DELAY_WR_0
+
+
+#endif /* #ifndef __PATI_H_ */
diff --git a/board/mpl/pati/pci_eeprom.h b/board/mpl/pati/pci_eeprom.h
new file mode 100644
index 0000000..9658808
--- /dev/null
+++ b/board/mpl/pati/pci_eeprom.h
@@ -0,0 +1,91 @@
+
+#ifndef __PCI_EEPROM_H_
+#define __PCI_EEPROM_H_	1
+
+#include "pati.h"
+/******************************************************************************
+ * Eeprom Support
+ ******************************************************************************/
+/**********************************************
+*               Definitions
+**********************************************/
+#define EE46_CMD_LEN    9       /* Bits in instructions */
+#define EE56_CMD_LEN    11      /* Bits in instructions */
+#define EE66_CMD_LEN    11      /* Bits in instructions */
+#define EE_READ         0x0180  /* 01 1000 0000 read instruction */
+#define EE_WRITE        0x0140  /* 01 0100 0000 write instruction */
+#define EE_WREN         0x0130  /* 01 0011 0000 write enable instruction */
+#define EE_WRALL        0x0110  /* 01 0001 0000 write all registers */
+#define EE_PRREAD       0x0180  /* 01 1000 0000 read address stored in Protect Register */
+#define EE_PRWRITE      0x0140  /* 01 0100 0000 write the address into PR */
+#define EE_WDS          0x0100  /* 01 0000 0000 write disable instruction */
+#define EE_PREN         0x0130  /* 01 0011 0000 protect enable instruction */
+#define EE_PRCLEAR      0x01FF  /* 01 1111 1111 clear protect register instr */
+#define EE_PRDS         0x0100  /* 01 0000 0000 ONE TIME ONLY, permenant */
+
+/***************************************************
+ * EEPROM
+ ***************************************************/
+#define LOW_WORD(x)	(((x) & 0xFFFF))
+#define HIGH_WORD(x)	(((x) >> 16) & 0xFFFF)
+
+typedef struct pci_eeprom_t {
+	unsigned short offset;
+	unsigned short value;
+} pci_eeprom;
+
+static pci_eeprom pati_eeprom[] = {
+	{ 0x00,PCI_DEVICE_ID_PATI }, 	/* PCI Device ID PCIIDR[31:16] */
+	{ 0x02,PCI_VENDOR_ID_MPL }, 	/* PCI Vendor ID PCIIDR[15:0] */
+	{ 0x04,PCI_CLASS_PROCESSOR_POWERPC }, 	/* PCI Class Code PCICCR[23:8] */
+	{ 0x06,0x00BA }, 	/* PCI Class Code / PCI Revision ID PCICCR[7:0] / PCIREV[7:0] */
+	{ 0x08,0x0007 }, 	/* PCI Maximum Latency / PCI Minimum Grant PCIMLR[7:0] / PCIMGR[7:0] */
+	{ 0x0A,0x0100 }, 	/* PCI Interrupt Pin / PCI Interrupt Line PCIIPR[7:0] / PCIILR[7:0] */
+	{ 0x0C,0x0000 }, 	/* MSW of Mailbox 0 (User Defined) PCI9056_MAILBOX0[31:16] */
+	{ 0x0E,0x0000 }, 	/* LSW of Mailbox 0 (User Defined) PCI9056_MAILBOX0[15:0] */
+	{ 0x10,0x0000 }, 	/* MSW of Mailbox 1 (User Defined) PCI9056_MAILBOX1[31:16] */
+	{ 0x12,0x0000 }, 	/* LSW of Mailbox 1 (User Defined) PCI9056_MAILBOX1[15:0] */
+	{ 0x14,HIGH_WORD(PATI_LOC_CFG_MASK) }, 	/* MSW of Direct Slave Local Address Space 0 Range LAS0RR[31:16] */
+	{ 0x16,LOW_WORD(PATI_LOC_CFG_MASK) }, 	/* LSW of Direct Slave Local Address Space 0 Range LAS0RR[15:0] */
+	{ 0x18,HIGH_WORD(PATI_LOC_CFG_ADDR) }, 	/* MSW of Direct Slave Local Address Space 0 Local Base Address (Remap) LAS0BA[31:16] (CFG) */
+	{ 0x1A,LOW_WORD(PATI_LOC_CFG_ADDR)|1 }, 	/* LSW of Direct Slave Local Address Space 0 Local Base Address (Remap) LAS0BA[15:2, 0], Reserved [1] */
+	{ 0x1C,0x0000 }, 	/* MSW of Mode/DMA Arbitration MARBR[31, 29:16] or DMAARB[31, 29:16], Reserved [30] */
+	{ 0x1E,0x0000 }, 	/* LSW of Mode/DMA Arbitration MARBR[15:0] or DMAARB[15:0] */
+	{ 0x20,0x0030 }, 	/* Local Miscellaneous Control 2 / Serial EEPROM WP Addr Boundary LMISC2[5:0], Res[7:6] / PROT_AREA[6:0], Res[7] */
+	{ 0x22,0x0510 }, 	/* Local Miscellaneous Control 1 / Local Bus Big/Little Endian Descriptor LMISC1[7:0] / BIGEND[7:0] */
+	{ 0x24,0x0000 }, 	/* MSW of Direct Slave Expansion ROM Range EROMRR[31:16] */
+	{ 0x26,0x0000 }, 	/* LSW of Direct Slave Expansion ROM Range EROMRR[15:11, 0], Reserved [10:1]  */
+	{ 0x28,0x0000 }, 	/* MSW of Direct Slave Expansion ROM Local Base Address (Remap) and BREQo Control EROMBA[31:16] */
+	{ 0x2A,0x0000 }, 	/* LSW of Direct Slave Expansion ROM Local Base Address (Remap) and BREQo Control EROMBA[15:11, 5:0], Reserved [10:6] */
+	{ 0x2C,(0x4243 | HIGH_WORD((PATI_LOC_CFG_SPACE0_ATTR))) }, 	/* MSW of Local Address Space 0/Expansion ROM Bus Region Descriptor LBRD0[31:16] */
+	{ 0x2E,LOW_WORD(PATI_LOC_CFG_SPACE0_ATTR) }, 	/* LSW of Local Address Space 0/Expansion ROM Bus Region Descriptor LBRD0[15:0] */
+	{ 0x30,HIGH_WORD(PATI_DMASTER_MASK) }, 	/* MSW of Local Range for Direct Master-to-PCI DMRR[31:16] */
+	{ 0x32,LOW_WORD(PATI_DMASTER_MASK) }, 	/* LSW of Local Range for Direct Master-to-PCI (Reserved) DMRR[15:0] */
+	{ 0x34,HIGH_WORD(PATI_DMASTER_ADDR) }, 	/* MSW of Local Base Address for Direct Master-to-PCI Memory DMLBAM[31:16] */
+	{ 0x36,LOW_WORD(PATI_DMASTER_ADDR) }, 	/* LSW of Local Base Address for Direct Master-to-PCI Memory (Reserved) DMLBAM[15:0] */
+	{ 0x38,0x0000 }, 	/* MSW of Local Bus Address for Direct Master-to-PCI I/O Configuration DMLBAI[31:16] */
+	{ 0x3A,0x0000 }, 	/* LSW of Local Bus Address for Direct Master-to-PCI I/O Configuration (Reserved) DMLBAI[15:0] */
+	{ 0x3C,0x0000 }, 	/* MSW of PCI Base Address (Remap) for Direct Master-to-PCI Memory DMPBAM[31:16] */
+	{ 0x3E,0x0000 }, 	/* LSW of PCI Base Address (Remap) for Direct Master-to-PCI Memory DMPBAM[15:0] */
+	{ 0x40,0x0000 }, 	/* MSW of PCI Configuration Address for Direct Master-to-PCI I/O Configuration DMCFGA[31, 23:16] Reserved [30:24]*/
+	{ 0x42,0x0000 }, 	/* LSW of PCI Configuration Address for Direct Master-to-PCI I/O Configuration DMCFGA[15:0] */
+	{ 0x44,0x0000 }, 	/* PCI Subsystem ID PCISID[15:0] */
+	{ 0x46,0x0000 }, 	/* PCI Subsystem Vendor ID PCISVID[15:0] */
+	{ 0x48,HIGH_WORD(PATI_LOC_SDRAM_MASK) }, 	/* MSW of Direct Slave Local Address Space 1 Range (1 MB) LAS1RR[31:16] */
+	{ 0x4A,LOW_WORD(PATI_LOC_SDRAM_MASK) }, 	/* LSW of Direct Slave Local Address Space 1 Range (1 MB) LAS1RR[15:0] */
+	{ 0x4C,HIGH_WORD(PATI_LOC_SDRAM_ADDR) }, 	/* MSW of Direct Slave Local Address Space 1 Local Base Address (Remap) LAS1BA[31:16] (SDRAM) */
+	{ 0x4E,LOW_WORD(PATI_LOC_SDRAM_ADDR) | 0x1 }, 	/* LSW of Direct Slave Local Address Space 1 Local Base Address (Remap) LAS1BA[15:2, 0], Reserved [1] */
+	{ 0x50,HIGH_WORD(PATI_LOC_SDRAM_SPACE1_ATTR) }, 	/* MSW of Local Address Space 1 Bus Region Descriptor LBRD1[31:16] */
+	{ 0x52,LOW_WORD(PATI_LOC_SDRAM_SPACE1_ATTR) }, 	/* LSW of Local Address Space 1 Bus Region Descriptor (Reserved) LBRD1[15:0] */
+	{ 0x54,0x0000 }, 	/* Hot Swap Control/Status (Reserved) Reserved */
+	{ 0x56,0x0000 }, 	/* Hot Swap Next Capability Pointer / Hot Swap Control HS_NEXT[7:0] / HS_CNTL[7:0] */
+	{ 0x58,0x0000 }, 	/* Reserved Reserved */
+	{ 0x5A,0x0000 }, 	/* PCI Arbiter Control PCIARB[3:0], Reserved [15:4] */
+	{ 0x5C,0x0000 }, 	/* Power Management Capabilities PMC[15:9, 2:0] */
+	{ 0x5E,0x0000 }, 	/* Power Management Next Capability Pointer (Reserved) / Power Management Capability ID (Reserved) Reserved*/
+	{ 0x60,0x0000 }, 	/* Power Management Data / PMCSR Bridge Support Extension (Reserved) PMDATA[7:0] / Reserved */
+	{ 0x62,0x0000 }, 	/* Power Management Control/Status PMCSR[14:8] */
+	{ 0xFFFF,0xFFFF} 	/* terminaror */
+};
+#define PATI_EEPROM_LAST_OFFSET	0x64
+#endif /* #ifndef __PCI_EEPROM_H_ */
diff --git a/board/mpl/pati/plx9056.h b/board/mpl/pati/plx9056.h
new file mode 100644
index 0000000..763a793
--- /dev/null
+++ b/board/mpl/pati/plx9056.h
@@ -0,0 +1,114 @@
+/*
+ * (C) Copyright 2003
+ * Denis Peter, d.peter@mpl.ch
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+/* PLX9096 register definitions
+*/
+#ifndef __PLX9056_H_
+#define __PLX9056_H_	1
+
+#include <pci.h>
+
+#ifdef PLX9056_LOC
+#define LOCAL_OFFSET					0x080
+/* PCI Config regs */
+#else
+#define LOCAL_OFFSET					0x000
+#endif
+
+#define PCI9056_VENDOR_ID            PCI_VENDOR_ID
+//#define PCI9656_DEVICE_ID            PCI_DEVICE_ID
+#define PCI9056_COMMAND              PCI_COMMAND
+//#define PCI9656_STATUS               PCI_STATUS
+#define PCI9056_REVISION             PCI_REVISION_ID
+
+#define PCI9056_CACHE_SIZE           PCI_CACHE_LINE_SIZE
+#define PCI9056_RTR_BASE             PCI_BASE_ADDRESS_0
+#define PCI9056_RTR_IO_BASE          PCI_BASE_ADDRESS_1
+#define PCI9056_LOCAL_BASE0          PCI_BASE_ADDRESS_2
+#define PCI9056_LOCAL_BASE1          PCI_BASE_ADDRESS_3
+#define PCI9056_UNUSED_BASE1         PCI_BASE_ADDRESS_4
+#define PCI9056_UNUSED_BASE2         PCI_BASE_ADDRESS_5
+#define PCI9056_CIS_PTR              PCI_CARDBUS_CIS
+#define PCI9056_SUB_ID               PCI_SUBSYSTEM_VENDOR_ID
+#define PCI9056_EXP_ROM_BASE         PCI_ROM_ADDRESS
+#define PCI9056_CAP_PTR              PCI_CAPABILITY_LIST
+#define PCI9056_INT_LINE             PCI_INTERRUPT_LINE
+
+#if defined(PLX9056_LOC)
+    #define PCI9056_PM_CAP_ID            0x180
+    #define PCI9056_PM_CSR               0x184
+    #define PCI9056_HS_CAP_ID            0x188
+    #define PCI9056_VPD_CAP_ID           0x18C
+    #define PCI9056_VPD_DATA             0x190
+#endif
+
+
+
+#define PCI_DEVICE_ID_PLX9056		0x9056
+
+/* Local Configuration Registers Accessible via the PCI Base address + Variable */
+#define PCI9056_SPACE0_RANGE         (0x000 + LOCAL_OFFSET)
+#define PCI9056_SPACE0_REMAP         (0x004 + LOCAL_OFFSET)
+#define PCI9056_LOCAL_DMA_ARBIT      (0x008 + LOCAL_OFFSET)
+#define PCI9056_ENDIAN_DESC          (0x00c + LOCAL_OFFSET)
+#define PCI9056_EXP_ROM_RANGE        (0x010 + LOCAL_OFFSET)
+#define PCI9056_EXP_ROM_REMAP        (0x014 + LOCAL_OFFSET)
+#define PCI9056_SPACE0_ROM_DESC      (0x018 + LOCAL_OFFSET)
+#define PCI9056_DM_RANGE             (0x01c + LOCAL_OFFSET)
+#define PCI9056_DM_MEM_BASE          (0x020 + LOCAL_OFFSET)
+#define PCI9056_DM_IO_BASE           (0x024 + LOCAL_OFFSET)
+#define PCI9056_DM_PCI_MEM_REMAP     (0x028 + LOCAL_OFFSET)
+#define PCI9056_DM_PCI_IO_CONFIG     (0x02c + LOCAL_OFFSET)
+#define PCI9056_SPACE1_RANGE         (0x0f0 + LOCAL_OFFSET)
+#define PCI9056_SPACE1_REMAP         (0x0f4 + LOCAL_OFFSET)
+#define PCI9056_SPACE1_DESC          (0x0f8 + LOCAL_OFFSET)
+#define PCI9056_DM_DAC               (0x0fc + LOCAL_OFFSET)
+
+#ifdef PLX9056_LOC
+#define PCI9056_ARBITER_CTRL         0x1A0
+#define PCI9056_ABORT_ADDRESS        0x1A4
+#endif
+
+/* Runtime registers  PCI Address + LOCAL_OFFSET */
+#ifdef PLX9056_LOC
+#define PCI9056_MAILBOX0				0x0C0
+#define PCI9056_MAILBOX1				0x0C4
+#else
+#define PCI9056_MAILBOX0				0x078
+#define PCI9056_MAILBOX1				0x07c
+#endif
+
+#define PCI9056_MAILBOX2				(0x048 + LOCAL_OFFSET)
+#define PCI9056_MAILBOX3				(0x04c + LOCAL_OFFSET)
+#define PCI9056_MAILBOX4				(0x050 + LOCAL_OFFSET)
+#define PCI9056_MAILBOX5				(0x054 + LOCAL_OFFSET)
+#define PCI9056_MAILBOX6				(0x058 + LOCAL_OFFSET)
+#define PCI9056_MAILBOX7				(0x05c + LOCAL_OFFSET)
+#define PCI9056_PCI_TO_LOC_DBELL		(0x060 + LOCAL_OFFSET)
+#define PCI9056_LOC_TO_PCI_DBELL		(0x064 + LOCAL_OFFSET)
+#define PCI9056_INT_CTRL_STAT			(0x068 + LOCAL_OFFSET)
+#define PCI9056_EEPROM_CTRL_STAT		(0x06c + LOCAL_OFFSET)
+#define PCI9056_PERM_VENDOR_ID		(0x070 + LOCAL_OFFSET)
+#define PCI9056_REVISION_ID			(0x074 + LOCAL_OFFSET)
+
+
+#endif /* #ifndef __PLX9056_H_ */
+
diff --git a/board/mpl/pati/u-boot.lds b/board/mpl/pati/u-boot.lds
new file mode 100644
index 0000000..3188801
--- /dev/null
+++ b/board/mpl/pati/u-boot.lds
@@ -0,0 +1,137 @@
+/*
+ * (C) Copyright 2001	Wolfgang Denk, DENX Software Engineering, wd@denx.de
+ * (C) Copyright 2003	Martin Winistoerfer, martinwinistoerfer@gmx.ch
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_ARCH(powerpc)
+SEARCH_DIR(/lib); SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/local/lib); SEARCH_DIR(/usr/local/powerpc-any-elf/lib);
+/* Do we need any of these for elf?
+   __DYNAMIC = 0;    */
+SECTIONS
+{
+  /* Read-only sections, merged into text segment: */
+  . = + SIZEOF_HEADERS;
+  .interp : { *(.interp) }
+  .hash          : { *(.hash)		}
+  .dynsym        : { *(.dynsym)		}
+  .dynstr        : { *(.dynstr)		}
+  .rel.text      : { *(.rel.text)		}
+  .rela.text     : { *(.rela.text) 	}
+  .rel.data      : { *(.rel.data)		}
+  .rela.data     : { *(.rela.data) 	}
+  .rel.rodata    : { *(.rel.rodata) 	}
+  .rela.rodata   : { *(.rela.rodata) 	}
+  .rel.got       : { *(.rel.got)		}
+  .rela.got      : { *(.rela.got)		}
+  .rel.ctors     : { *(.rel.ctors)	}
+  .rela.ctors    : { *(.rela.ctors)	}
+  .rel.dtors     : { *(.rel.dtors)	}
+  .rela.dtors    : { *(.rela.dtors)	}
+  .rel.bss       : { *(.rel.bss)		}
+  .rela.bss      : { *(.rela.bss)		}
+  .rel.plt       : { *(.rel.plt)		}
+  .rela.plt      : { *(.rela.plt)		}
+  .init          : { *(.init)	}
+  .plt : { *(.plt) }
+  .text      :
+  {
+    /* WARNING - the following is hand-optimized to fit within	*/
+    /* the sector layout of our flash chips!	XXX FIXME XXX	*/
+
+    cpu/mpc5xx/start.o	(.text)
+
+    *(.text)
+    *(.fixup)
+    *(.got1)
+  }
+  _etext = .;
+  PROVIDE (etext = .);
+  .rodata    :
+  {
+    *(.rodata)
+    *(.rodata1)
+    *(.rodata.str1.4)
+  }
+  .fini      : { *(.fini)    } =0
+  .ctors     : { *(.ctors)   }
+  .dtors     : { *(.dtors)   }
+
+  /* Read-write section, merged into data segment: */
+  . = (. + 0x00FF) & 0xFFFFFF00;
+  _erotext = .;
+  PROVIDE (erotext = .);
+  .reloc   :
+  {
+    *(.got)
+    _GOT2_TABLE_ = .;
+    *(.got2)
+    _FIXUP_TABLE_ = .;
+    *(.fixup)
+  }
+  __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2;
+  __fixup_entries = (. - _FIXUP_TABLE_)>>2;
+
+  .data    :
+  {
+    *(.data)
+    *(.data1)
+    *(.sdata)
+    *(.sdata2)
+    *(.dynamic)
+    CONSTRUCTORS
+  }
+  _edata  =  .;
+  PROVIDE (edata = .);
+
+  __u_boot_cmd_start = .;
+  .u_boot_cmd : { *(.u_boot_cmd) }
+  __u_boot_cmd_end = .;
+
+
+  __start___ex_table = .;
+  __ex_table : { *(__ex_table) }
+  __stop___ex_table = .;
+
+  . = ALIGN(256);
+  __init_begin = .;
+  .text.init : { *(.text.init) }
+  .data.init : { *(.data.init) }
+  . = ALIGN(256);
+  __init_end = .;
+
+  __bss_start = .;
+  .bss       :
+  {
+   *(.sbss) *(.scommon)
+   *(.dynbss)
+   *(.bss)
+   *(COMMON)
+  }
+
+  _end = . ;
+  PROVIDE (end = .);
+/*   . = env_start;
+	.ppcenv	:
+	{
+		common/environment.o (.ppcenv)
+	}
+*/
+}