diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 084f113..64b8371 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -51,7 +51,8 @@
 	armada-388-clearfog.dtb			\
 	armada-388-gp.dtb			\
 	armada-xp-gp.dtb			\
-	armada-xp-maxbcm.dtb
+	armada-xp-maxbcm.dtb			\
+	armada-xp-synology-ds414.dtb
 
 dtb-$(CONFIG_ARCH_UNIPHIER) += \
 	uniphier-ph1-ld4-ref.dtb \
diff --git a/arch/arm/dts/armada-xp-synology-ds414.dts b/arch/arm/dts/armada-xp-synology-ds414.dts
new file mode 100644
index 0000000..0a60ddf
--- /dev/null
+++ b/arch/arm/dts/armada-xp-synology-ds414.dts
@@ -0,0 +1,337 @@
+/*
+ * Device Tree file for Synology DS414
+ *
+ * Copyright (C) 2014, Arnaud EBALARD <arno@natisbad.org>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version
+ * 2 of the License, or (at your option) any later version.
+ *
+ * Note: this Device Tree assumes that the bootloader has remapped the
+ * internal registers to 0xf1000000 (instead of the old 0xd0000000).
+ * The 0xf1000000 is the default used by the recent, DT-capable, U-Boot
+ * bootloaders provided by Marvell. It is used in recent versions of
+ * DSM software provided by Synology. Nonetheless, some earlier boards
+ * were delivered with an older version of u-boot that left internal
+ * registers mapped at 0xd0000000. If you have such a device you will
+ * not be able to directly boot a kernel based on this Device Tree. In
+ * that case, the preferred solution is to update your bootloader (e.g.
+ * by upgrading to latest version of DSM, or building a new one and
+ * installing it from u-boot prompt) or adjust the Devive Tree
+ * (s/0xf1000000/0xd0000000/ in 'ranges' below).
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+#include "armada-xp-mv78230.dtsi"
+
+/ {
+	model = "Synology DS414";
+	compatible = "synology,ds414", "marvell,armadaxp-mv78230",
+		     "marvell,armadaxp", "marvell,armada-370-xp";
+
+	chosen {
+		bootargs = "console=ttyS0,115200 earlyprintk";
+		stdout-path = &uart0;
+	};
+
+	aliases {
+		spi0 = &spi0;
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0 0x00000000 0 0x40000000>; /* 1GB */
+	};
+
+	soc {
+		ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xf1000000 0x100000
+			  MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000>;
+
+		pcie-controller {
+			status = "okay";
+
+			/*
+			 * Connected to Marvell 88SX7042 SATA-II controller
+			 * handling the four disks.
+			 */
+			pcie@1,0 {
+				/* Port 0, Lane 0 */
+				status = "okay";
+			};
+
+			/*
+			 * Connected to EtronTech EJ168A XHCI controller
+			 * providing the two rear USB 3.0 ports.
+			 */
+			pcie@5,0 {
+				/* Port 1, Lane 0 */
+				status = "okay";
+			};
+		};
+
+		internal-regs {
+
+			/* RTC is provided by Seiko S-35390A below */
+			rtc@10300 {
+				status = "disabled";
+			};
+
+			spi0: spi@10600 {
+				status = "okay";
+				u-boot,dm-pre-reloc;
+
+				spi-flash@0 {
+					u-boot,dm-pre-reloc;
+					#address-cells = <1>;
+					#size-cells = <1>;
+					compatible = "micron,n25q064";
+					reg = <0>; /* Chip select 0 */
+					spi-max-frequency = <20000000>;
+
+					/*
+					 * Warning!
+					 *
+					 * Synology u-boot uses its compiled-in environment
+					 * and it seems Synology did not care to change u-boot
+					 * default configuration in order to allow saving a
+					 * modified environment at a sensible location. So,
+					 * if you do a 'saveenv' under u-boot, your modified
+					 * environment will be saved at 1MB after the start
+					 * of the flash, i.e. in the middle of the uImage.
+					 * For that reason, it is strongly advised not to
+					 * change the default environment, unless you know
+					 * what you are doing.
+					 */
+					partition@00000000 { /* u-boot */
+						label = "RedBoot";
+						reg = <0x00000000 0x000d0000>; /* 832KB */
+					};
+
+					partition@000c0000 { /* uImage */
+						label = "zImage";
+						reg = <0x000d0000 0x002d0000>; /* 2880KB */
+					};
+
+					partition@003a0000 { /* uInitramfs */
+						label = "rd.gz";
+						reg = <0x003a0000 0x00430000>; /* 4250KB */
+					};
+
+					partition@007d0000 { /* MAC address and serial number */
+						label = "vendor";
+						reg = <0x007d0000 0x00010000>; /* 64KB */
+					};
+
+					partition@007e0000 {
+						label = "RedBoot config";
+						reg = <0x007e0000 0x00010000>; /* 64KB */
+					};
+
+					partition@007f0000 {
+						label = "FIS directory";
+						reg = <0x007f0000 0x00010000>; /* 64KB */
+					};
+				};
+			};
+
+			i2c@11000 {
+				clock-frequency = <400000>;
+				status = "okay";
+
+				s35390a: s35390a@30 {
+					 compatible = "sii,s35390a";
+					 reg = <0x30>;
+				};
+			};
+
+			/* Connected to a header on device's PCB. This
+			 * provides the main console for the device.
+			 *
+			 * Warning: the device may not boot with a 3.3V
+			 * USB-serial converter connected when the power
+			 * button is pressed. The converter needs to be
+			 * connected a few seconds after pressing the
+			 * power button. This is possibly due to UART0_TXD
+			 * pin being sampled at reset (bit 0 of SAR).
+			 */
+			serial@12000 {
+				status = "okay";
+				u-boot,dm-pre-reloc;
+			};
+
+			/* Connected to a Microchip PIC16F883 for power control */
+			serial@12100 {
+				status = "okay";
+			};
+
+			poweroff@12100 {
+				compatible = "synology,power-off";
+				reg = <0x12100 0x100>;
+				clocks = <&coreclk 0>;
+			};
+
+			/* Front USB 2.0 port */
+			usb@50000 {
+				status = "okay";
+			};
+
+			mdio {
+				phy0: ethernet-phy@0 { /* Marvell 88E1512 */
+					reg = <0>;
+				};
+
+				phy1: ethernet-phy@1 { /* Marvell 88E1512 */
+					reg = <1>;
+				};
+			};
+
+			ethernet@70000 {
+				status = "okay";
+				pinctrl-0 = <&ge0_rgmii_pins>;
+				pinctrl-names = "default";
+				phy = <&phy1>;
+				phy-mode = "rgmii-id";
+			};
+
+			ethernet@74000 {
+				pinctrl-0 = <&ge1_rgmii_pins>;
+				pinctrl-names = "default";
+				status = "okay";
+				phy = <&phy0>;
+				phy-mode = "rgmii-id";
+			};
+		};
+	};
+
+	regulators {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		pinctrl-0 = <&sata1_pwr_pin &sata2_pwr_pin
+			     &sata3_pwr_pin &sata4_pwr_pin>;
+		pinctrl-names = "default";
+
+		sata1_regulator: sata1-regulator {
+			compatible = "regulator-fixed";
+			reg = <1>;
+			regulator-name = "SATA1 Power";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			startup-delay-us = <2000000>;
+			enable-active-high;
+			regulator-always-on;
+			regulator-boot-on;
+			gpio = <&gpio1 10 GPIO_ACTIVE_HIGH>;
+		};
+
+		sata2_regulator: sata2-regulator {
+			compatible = "regulator-fixed";
+			reg = <2>;
+			regulator-name = "SATA2 Power";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			startup-delay-us = <4000000>;
+			enable-active-high;
+			regulator-always-on;
+			regulator-boot-on;
+			gpio = <&gpio1 12 GPIO_ACTIVE_HIGH>;
+		};
+
+		sata3_regulator: sata3-regulator {
+			compatible = "regulator-fixed";
+			reg = <3>;
+			regulator-name = "SATA3 Power";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			startup-delay-us = <6000000>;
+			enable-active-high;
+			regulator-always-on;
+			regulator-boot-on;
+			gpio = <&gpio1 13 GPIO_ACTIVE_HIGH>;
+		};
+
+		sata4_regulator: sata4-regulator {
+			compatible = "regulator-fixed";
+			reg = <4>;
+			regulator-name = "SATA4 Power";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			startup-delay-us = <8000000>;
+			enable-active-high;
+			regulator-always-on;
+			regulator-boot-on;
+			gpio = <&gpio1 14 GPIO_ACTIVE_HIGH>;
+		};
+	};
+};
+
+&pinctrl {
+	sata1_pwr_pin: sata1-pwr-pin {
+		marvell,pins = "mpp42";
+		marvell,function = "gpio";
+	};
+
+	sata2_pwr_pin: sata2-pwr-pin {
+		marvell,pins = "mpp44";
+		marvell,function = "gpio";
+	};
+
+	sata3_pwr_pin: sata3-pwr-pin {
+		marvell,pins = "mpp45";
+		marvell,function = "gpio";
+	};
+
+	sata4_pwr_pin: sata4-pwr-pin {
+		marvell,pins = "mpp46";
+		marvell,function = "gpio";
+	};
+
+	sata1_pres_pin: sata1-pres-pin {
+		marvell,pins = "mpp34";
+		marvell,function = "gpio";
+	};
+
+	sata2_pres_pin: sata2-pres-pin {
+		marvell,pins = "mpp35";
+		marvell,function = "gpio";
+	};
+
+	sata3_pres_pin: sata3-pres-pin {
+		marvell,pins = "mpp40";
+		marvell,function = "gpio";
+	};
+
+	sata4_pres_pin: sata4-pres-pin {
+		marvell,pins = "mpp41";
+		marvell,function = "gpio";
+	};
+
+	syno_id_bit0_pin: syno-id-bit0-pin {
+		marvell,pins = "mpp26";
+		marvell,function = "gpio";
+	};
+
+	syno_id_bit1_pin: syno-id-bit1-pin {
+		marvell,pins = "mpp28";
+		marvell,function = "gpio";
+	};
+
+	syno_id_bit2_pin: syno-id-bit2-pin {
+		marvell,pins = "mpp29";
+		marvell,function = "gpio";
+	};
+
+	fan1_alarm_pin: fan1-alarm-pin {
+		marvell,pins = "mpp33";
+		marvell,function = "gpio";
+	};
+
+	fan2_alarm_pin: fan2-alarm-pin {
+		marvell,pins = "mpp32";
+		marvell,function = "gpio";
+	};
+};
diff --git a/arch/arm/mach-mvebu/Kconfig b/arch/arm/mach-mvebu/Kconfig
index 35d44f6..b962846 100644
--- a/arch/arm/mach-mvebu/Kconfig
+++ b/arch/arm/mach-mvebu/Kconfig
@@ -38,6 +38,10 @@
 	bool "Support db-mv784mp-gp"
 	select MV78460
 
+config TARGET_DS414
+	bool "Support Synology DS414"
+	select MV78230
+
 config TARGET_MAXBCM
 	bool "Support maxbcm"
 	select MV78460
@@ -48,18 +52,21 @@
 	default "clearfog" if TARGET_CLEARFOG
 	default "db-88f6820-gp" if TARGET_DB_88F6820_GP
 	default "db-mv784mp-gp" if TARGET_DB_MV784MP_GP
+	default "ds414" if TARGET_DS414
 	default "maxbcm" if TARGET_MAXBCM
 
 config SYS_CONFIG_NAME
 	default "clearfog" if TARGET_CLEARFOG
 	default "db-88f6820-gp" if TARGET_DB_88F6820_GP
 	default "db-mv784mp-gp" if TARGET_DB_MV784MP_GP
+	default "ds414" if TARGET_DS414
 	default "maxbcm" if TARGET_MAXBCM
 
 config SYS_VENDOR
 	default "Marvell" if TARGET_DB_MV784MP_GP
 	default "Marvell" if TARGET_DB_88F6820_GP
 	default "solidrun" if TARGET_CLEARFOG
+	default "Synology" if TARGET_DS414
 
 config SYS_SOC
 	default "mvebu"
diff --git a/arch/arm/mach-mvebu/serdes/axp/board_env_spec.h b/arch/arm/mach-mvebu/serdes/axp/board_env_spec.h
index f00f327..c8d9485 100644
--- a/arch/arm/mach-mvebu/serdes/axp/board_env_spec.h
+++ b/arch/arm/mach-mvebu/serdes/axp/board_env_spec.h
@@ -44,7 +44,7 @@
 #define DB_784MP_GP_ID			(RD_78460_SERVER_REV2_ID + 1)
 #define RD_78460_CUSTOMER_ID		(DB_784MP_GP_ID + 1)
 #define MV_MAX_BOARD_ID			(RD_78460_CUSTOMER_ID + 1)
-#define INVALID_BAORD_ID		0xFFFFFFFF
+#define INVALID_BOARD_ID		0xFFFFFFFF
 
 /* Sample at Reset */
 #define MPP_SAMPLE_AT_RESET(id)		(0x18230 + (id * 4))
diff --git a/board/Synology/ds414/Makefile b/board/Synology/ds414/Makefile
new file mode 100644
index 0000000..0f4c32d
--- /dev/null
+++ b/board/Synology/ds414/Makefile
@@ -0,0 +1,7 @@
+#
+# Copyright (C) 2015 Phil Sutter <phil@nwl.cc>
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+obj-y :=	ds414.o
diff --git a/board/Synology/ds414/ds414.c b/board/Synology/ds414/ds414.c
new file mode 100644
index 0000000..d563e89
--- /dev/null
+++ b/board/Synology/ds414/ds414.c
@@ -0,0 +1,185 @@
+/*
+ *
+ * Copyright (C) 2015 Phil Sutter <phil@nwl.cc>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <miiphy.h>
+#include <asm/io.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/soc.h>
+#include <linux/mbus.h>
+
+#include "../drivers/ddr/marvell/axp/ddr3_hw_training.h"
+#include "../arch/arm/mach-mvebu/serdes/axp/high_speed_env_spec.h"
+#include "../arch/arm/mach-mvebu/serdes/axp/board_env_spec.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+/* GPP and MPP settings as found in mvBoardEnvSpec.c of Synology's U-Boot */
+
+#define DS414_GPP_OUT_VAL_LOW		(BIT(25) | BIT(30))
+#define DS414_GPP_OUT_VAL_MID		(BIT(10) | BIT(15))
+#define DS414_GPP_OUT_VAL_HIGH		(0)
+
+#define DS414_GPP_OUT_POL_LOW		(0)
+#define DS414_GPP_OUT_POL_MID		(0)
+#define DS414_GPP_OUT_POL_HIGH		(0)
+
+#define DS414_GPP_OUT_ENA_LOW		(~(BIT(25) | BIT(30)))
+#define DS414_GPP_OUT_ENA_MID		(~(BIT(10) | BIT(12) | \
+					   BIT(13) | BIT(14) | BIT(15)))
+#define DS414_GPP_OUT_ENA_HIGH		(~0)
+
+static const u32 ds414_mpp_control[] = {
+	0x11111111,
+	0x22221111,
+	0x22222222,
+	0x00000000,
+	0x11110000,
+	0x00004000,
+	0x00000000,
+	0x00000000,
+	0x00000000
+};
+
+/* DDR3 static MC configuration */
+
+/* 1G_v1 (4x2Gbits) adapted by DS414 */
+MV_DRAM_MC_INIT syno_ddr3_b0_667_1g_v1[MV_MAX_DDR3_STATIC_SIZE] = {
+	{0x00001400, 0x73014A28},	/*DDR SDRAM Configuration Register */
+	{0x00001404, 0x30000800},	/*Dunit Control Low Register */
+	{0x00001408, 0x44148887},	/*DDR SDRAM Timing (Low) Register */
+	{0x0000140C, 0x3AD83FEA},	/*DDR SDRAM Timing (High) Register */
+
+	{0x00001410, 0x14000000},	/*DDR SDRAM Address Control Register */
+
+	{0x00001414, 0x00000000},	/*DDR SDRAM Open Pages Control Register */
+	{0x00001418, 0x00000e00},	/*DDR SDRAM Operation Register */
+	{0x00001420, 0x00000004},	/*DDR SDRAM Extended Mode Register */
+	{0x00001424, 0x0000F3FF},	/*Dunit Control High Register */
+	{0x00001428, 0x000F8830},	/*Dunit Control High Register */
+	{0x0000142C, 0x054C36F4},	/*Dunit Control High Register */
+	{0x0000147C, 0x0000C671},
+
+	{0x000014a0, 0x00000001},
+	{0x000014a8, 0x00000100},	/*2:1 */
+	{0x00020220, 0x00000006},
+
+	{0x00001494, 0x00010000},	/*DDR SDRAM ODT Control (Low) Register */
+	{0x00001498, 0x00000000},	/*DDR SDRAM ODT Control (High) Register */
+	{0x0000149C, 0x00000001},	/*DDR Dunit ODT Control Register */
+
+	{0x000014C0, 0x192424C9},	/* DRAM address and Control Driving Strenght  */
+	{0x000014C4, 0x0AAA24C9},	/* DRAM Data and DQS Driving Strenght  */
+
+	{0x000200e8, 0x3FFF0E01},	/* DO NOT Modify - Open Mbus Window - 2G - Mbus is required for the training sequence*/
+	{0x00020184, 0x3FFFFFE0},	/* DO NOT Modify - Close fast path Window to - 2G */
+
+	{0x0001504, 0x3FFFFFE1},	/* CS0 Size */
+	{0x000150C, 0x00000000},	/* CS1 Size */
+	{0x0001514, 0x00000000},	/* CS2 Size */
+	{0x000151C, 0x00000000},	/* CS3 Size */
+
+	{0x00001538, 0x00000009},	/*Read Data Sample Delays Register */
+	{0x0000153C, 0x00000009},	/*Read Data Ready Delay Register */
+
+	{0x000015D0, 0x00000650},	/*MR0 */
+	{0x000015D4, 0x00000044},	/*MR1 */
+	{0x000015D8, 0x00000010},	/*MR2 */
+	{0x000015DC, 0x00000000},	/*MR3 */
+
+	{0x000015E4, 0x00203c18},	/*ZQC Configuration Register */
+	{0x000015EC, 0xF800A225},	/*DDR PHY */
+
+	{0x0, 0x0}
+};
+
+MV_DRAM_MODES ds414_ddr_modes[MV_DDR3_MODES_NUMBER] = {
+	{"ds414_1333-667",   0x3, 0x5, 0x0, A0, syno_ddr3_b0_667_1g_v1,  NULL},
+};
+
+extern MV_SERDES_CHANGE_M_PHY serdes_change_m_phy[];
+
+MV_BIN_SERDES_CFG ds414_serdes_cfg[] = {
+	{ MV_PEX_ROOT_COMPLEX, 0x02011111, 0x00000000,
+	  { PEX_BUS_MODE_X4, PEX_BUS_MODE_X1, PEX_BUS_DISABLED,
+	    PEX_BUS_DISABLED },
+	  0x0040, serdes_change_m_phy
+	}
+};
+
+MV_DRAM_MODES *ddr3_get_static_ddr_mode(void)
+{
+	return &ds414_ddr_modes[0];
+}
+
+MV_BIN_SERDES_CFG *board_serdes_cfg_get(u8 pex_mode)
+{
+	return &ds414_serdes_cfg[0];
+}
+
+u8 board_sat_r_get(u8 dev_num, u8 reg)
+{
+	return (0x1 << 1 | 1);
+}
+
+int board_early_init_f(void)
+{
+	int i;
+
+	/* Set GPP Out value */
+	reg_write(GPP_DATA_OUT_REG(0), DS414_GPP_OUT_VAL_LOW);
+	reg_write(GPP_DATA_OUT_REG(1), DS414_GPP_OUT_VAL_MID);
+	reg_write(GPP_DATA_OUT_REG(2), DS414_GPP_OUT_VAL_HIGH);
+
+	/* set GPP polarity */
+	reg_write(GPP_DATA_IN_POL_REG(0), DS414_GPP_OUT_POL_LOW);
+	reg_write(GPP_DATA_IN_POL_REG(1), DS414_GPP_OUT_POL_MID);
+	reg_write(GPP_DATA_IN_POL_REG(2), DS414_GPP_OUT_POL_HIGH);
+
+	/* Set GPP Out Enable */
+	reg_write(GPP_DATA_OUT_EN_REG(0), DS414_GPP_OUT_ENA_LOW);
+	reg_write(GPP_DATA_OUT_EN_REG(1), DS414_GPP_OUT_ENA_MID);
+	reg_write(GPP_DATA_OUT_EN_REG(2), DS414_GPP_OUT_ENA_HIGH);
+
+	for (i = 0; i < ARRAY_SIZE(ds414_mpp_control); i++)
+		reg_write(MPP_CONTROL_REG(i), ds414_mpp_control[i]);
+
+	return 0;
+}
+
+int board_init(void)
+{
+	u32 pwr_mng_ctrl_reg;
+
+	/* Adress of boot parameters */
+	gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;
+
+	/* Gate unused clocks
+	 *
+	 * Note: Disabling unused PCIe lanes will hang PCI bus scan.
+	 *       Once this is resolved, bits 10-12, 26 and 27 can be
+	 *       unset here as well.
+	 */
+	pwr_mng_ctrl_reg = reg_read(POWER_MNG_CTRL_REG);
+	pwr_mng_ctrl_reg &= ~(BIT(0));				/* Audio */
+	pwr_mng_ctrl_reg &= ~(BIT(1) | BIT(2));			/* GE3, GE2 */
+	pwr_mng_ctrl_reg &= ~(BIT(14) | BIT(15));		/* SATA0 link and core */
+	pwr_mng_ctrl_reg &= ~(BIT(16));				/* LCD */
+	pwr_mng_ctrl_reg &= ~(BIT(17));				/* SDIO */
+	pwr_mng_ctrl_reg &= ~(BIT(19) | BIT(20));		/* USB1 and USB2 */
+	pwr_mng_ctrl_reg &= ~(BIT(29) | BIT(30));		/* SATA1 link and core */
+	reg_write(POWER_MNG_CTRL_REG, pwr_mng_ctrl_reg);
+
+	return 0;
+}
+
+int checkboard(void)
+{
+	puts("Board: DS414\n");
+
+	return 0;
+}
diff --git a/board/Synology/ds414/kwbimage.cfg b/board/Synology/ds414/kwbimage.cfg
new file mode 100644
index 0000000..1f748db
--- /dev/null
+++ b/board/Synology/ds414/kwbimage.cfg
@@ -0,0 +1,12 @@
+#
+# Copyright (C) 2014 Stefan Roese <sr@denx.de>
+#
+
+# Armada XP uses version 1 image format
+VERSION		1
+
+# Boot Media configurations
+BOOT_FROM	spi
+
+# Binary Header (bin_hdr) with DDR3 training code
+BINARY spl/u-boot-spl-dtb.bin 0000005b 00000068
diff --git a/configs/ds414_defconfig b/configs/ds414_defconfig
new file mode 100644
index 0000000..4c3c1df
--- /dev/null
+++ b/configs/ds414_defconfig
@@ -0,0 +1,18 @@
+CONFIG_ARM=y
+CONFIG_ARCH_MVEBU=y
+CONFIG_SYS_MALLOC_F_LEN=0x2000
+CONFIG_TARGET_DS414=y
+CONFIG_DEFAULT_DEVICE_TREE="armada-xp-synology-ds414"
+CONFIG_SPL=y
+# CONFIG_CMD_IMLS is not set
+# CONFIG_CMD_FLASH is not set
+# CONFIG_CMD_SETEXPR is not set
+CONFIG_SPL_OF_TRANSLATE=y
+CONFIG_SPI_FLASH=y
+CONFIG_SPI_FLASH_BAR=y
+CONFIG_SPI_FLASH_STMICRO=y
+CONFIG_DEBUG_UART=y
+CONFIG_DEBUG_UART_BASE=0xd0012000
+CONFIG_DEBUG_UART_CLOCK=250000000
+CONFIG_DEBUG_UART_SHIFT=2
+CONFIG_SYS_NS16550=y
diff --git a/include/configs/ds414.h b/include/configs/ds414.h
new file mode 100644
index 0000000..e3c7087
--- /dev/null
+++ b/include/configs/ds414.h
@@ -0,0 +1,162 @@
+/*
+ * Copyright (C) 2014 Stefan Roese <sr@denx.de>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef _CONFIG_SYNOLOGY_DS414_H
+#define _CONFIG_SYNOLOGY_DS414_H
+
+/*
+ * High Level Configuration Options (easy to change)
+ */
+#define CONFIG_DISPLAY_BOARDINFO_LATE
+
+/*
+ * TEXT_BASE needs to be below 16MiB, since this area is scrubbed
+ * for DDR ECC byte filling in the SPL before loading the main
+ * U-Boot into it.
+ */
+#define	CONFIG_SYS_TEXT_BASE	0x00800000
+#define CONFIG_SYS_TCLK		250000000	/* 250MHz */
+
+/*
+ * Commands configuration
+ */
+#define CONFIG_SYS_NO_FLASH		/* Declare no flash (NOR/SPI) */
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_ENV
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_SF
+#define CONFIG_CMD_SPI
+#define CONFIG_CMD_TFTPPUT
+#define CONFIG_CMD_TIME
+#define CONFIG_CMD_USB
+
+/* I2C */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_MVTWSI
+#define CONFIG_I2C_MVTWSI_BASE0		MVEBU_TWSI_BASE
+#define CONFIG_SYS_I2C_SLAVE		0x0
+#define CONFIG_SYS_I2C_SPEED		100000
+
+/* SPI NOR flash default params, used by sf commands */
+#define CONFIG_SF_DEFAULT_SPEED		1000000
+#define CONFIG_SF_DEFAULT_MODE		SPI_MODE_3
+
+/* Environment in SPI NOR flash */
+#define CONFIG_ENV_IS_IN_SPI_FLASH
+#define CONFIG_ENV_OFFSET		0x7E0000   /* RedBoot config partition in DTS */
+#define CONFIG_ENV_SIZE			(64 << 10) /* 64KiB */
+#define CONFIG_ENV_SECT_SIZE		(64 << 10) /* 64KiB sectors */
+
+#define CONFIG_PHY_MARVELL		/* there is a marvell phy */
+#define CONFIG_PHY_ADDR			{ 0x1, 0x0 }
+#define CONFIG_SYS_NETA_INTERFACE_TYPE	PHY_INTERFACE_MODE_RGMII
+
+#define CONFIG_SYS_ALT_MEMTEST
+
+/* PCIe support */
+#ifndef CONFIG_SPL_BUILD
+#define CONFIG_PCI
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_PCI_ENUM
+#define CONFIG_PCI_MVEBU
+#define CONFIG_PCI_SCAN_SHOW
+#endif
+
+/* USB/EHCI/XHCI configuration */
+
+#define CONFIG_DM_USB
+#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
+
+/* FIXME: broken XHCI support
+ * Below defines should enable support for the two rear USB3 ports. Sadly, this
+ * does not work because:
+ * - xhci-pci seems to not support DM_USB, so with that enabled it is not
+ *   found.
+ * - USB init fails, controller does not respond in time */
+#if 0
+#undef CONFIG_DM_USB
+#define CONFIG_USB_XHCI
+#define CONFIG_USB_XHCI_PCI
+#define CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS 2
+#endif
+
+#if !defined(CONFIG_USB_XHCI)
+#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_MARVELL
+#define CONFIG_EHCI_IS_TDI
+#endif
+
+/* why is this only defined in mv-common.h if CONFIG_DM is undefined? */
+#define CONFIG_USB_STORAGE
+#define CONFIG_DOS_PARTITION
+#define CONFIG_ISO_PARTITION
+#define CONFIG_SUPPORT_VFAT
+#define CONFIG_SYS_MVFS
+
+/*
+ * mv-common.h should be defined after CMD configs since it used them
+ * to enable certain macros
+ */
+#include "mv-common.h"
+
+/*
+ * Memory layout while starting into the bin_hdr via the
+ * BootROM:
+ *
+ * 0x4000.4000 - 0x4003.4000	headers space (192KiB)
+ * 0x4000.4030			bin_hdr start address
+ * 0x4003.4000 - 0x4004.7c00	BootROM memory allocations (15KiB)
+ * 0x4007.fffc			BootROM stack top
+ *
+ * The address space between 0x4007.fffc and 0x400f.fff is not locked in
+ * L2 cache thus cannot be used.
+ */
+
+/* SPL */
+/* Defines for SPL */
+#define CONFIG_SPL_FRAMEWORK
+#define CONFIG_SPL_TEXT_BASE		0x40004030
+#define CONFIG_SPL_MAX_SIZE		((128 << 10) - 0x4030)
+
+#define CONFIG_SPL_BSS_START_ADDR	(0x40000000 + (128 << 10))
+#define CONFIG_SPL_BSS_MAX_SIZE		(16 << 10)
+
+#ifdef CONFIG_SPL_BUILD
+#define CONFIG_SYS_MALLOC_SIMPLE
+#endif
+
+#define CONFIG_SPL_STACK		(0x40000000 + ((192 - 16) << 10))
+#define CONFIG_SPL_BOOTROM_SAVE		(CONFIG_SPL_STACK + 4)
+
+#define CONFIG_SPL_LIBCOMMON_SUPPORT
+#define CONFIG_SPL_LIBGENERIC_SUPPORT
+#define CONFIG_SPL_SERIAL_SUPPORT
+#define CONFIG_SPL_I2C_SUPPORT
+
+/* SPL related SPI defines */
+#define CONFIG_SPL_SPI_SUPPORT
+#define CONFIG_SPL_SPI_FLASH_SUPPORT
+#define CONFIG_SPL_SPI_LOAD
+#define CONFIG_SPL_SPI_BUS		0
+#define CONFIG_SPL_SPI_CS		0
+#define CONFIG_SYS_SPI_U_BOOT_OFFS	0x24000
+
+/* DS414 bus width is 32bits */
+#define CONFIG_DDR_32BIT
+
+/* Use random ethernet address if not configured */
+#define CONFIG_LIB_RAND
+#define CONFIG_NET_RANDOM_ETHADDR
+
+/* Default Environment */
+#define CONFIG_BOOTCOMMAND	"sf read ${loadaddr} 0xd0000 0x700000; bootm"
+#define CONFIG_BOOTARGS		"console=ttyS0,115200"
+#define CONFIG_LOADADDR		0x80000
+#undef CONFIG_PREBOOT		/* override preboot for USB and SPI flash init */
+#define CONFIG_PREBOOT		"usb start; sf probe"
+
+#endif /* _CONFIG_SYNOLOGY_DS414_H */