/*
 * (C) Copyright 2007-2008
 * Dirk Eibach,  Guntermann & Drunck GmbH, eibach@gdsys.de
 *
 * SPDX-License-Identifier:	GPL-2.0+ 
 */

#ifndef __CONFIG_H
#define __CONFIG_H


#define CONFIG_405EP		1	/* this is a PPC405 CPU */
#define CONFIG_4xx		1	/*  member of PPC4xx family */
#define CONFIG_NEO	        1	/*  on a Neo board */

#define	CONFIG_SYS_TEXT_BASE	0xFFFC0000

/*
 * Include common defines/options for all AMCC eval boards
 */
#define CONFIG_HOSTNAME		neo
#define CONFIG_IDENT_STRING	" neo 0.02"
#include "amcc-common.h"

#define CONFIG_BOARD_EARLY_INIT_F
#define CONFIG_BOARD_EARLY_INIT_R
#define CONFIG_MISC_INIT_R
#define CONFIG_LAST_STAGE_INIT

#define CONFIG_SYS_CLK_FREQ	33333333 /* external frequency to pll   */

/*
 * Configure PLL
 */
#define PLLMR0_DEFAULT PLLMR0_266_133_66_33
#define PLLMR1_DEFAULT PLLMR1_266_133_66_33

/* new uImage format support */
#define CONFIG_FIT
#define CONFIG_FIT_VERBOSE	/* enable fit_format_{error,warning}() */

#define CONFIG_ENV_IS_IN_FLASH	/* use FLASH for environment vars */

/*
 * Default environment variables
 */
#define	CONFIG_EXTRA_ENV_SETTINGS					\
	CONFIG_AMCC_DEF_ENV						\
	CONFIG_AMCC_DEF_ENV_POWERPC					\
	CONFIG_AMCC_DEF_ENV_NOR_UPD					\
	"kernel_addr=fc000000\0"					\
	"fdt_addr=fc1e0000\0"						\
	"ramdisk_addr=fc200000\0"					\
	""

#define CONFIG_PHY_ADDR		4	/* PHY address			*/
#define CONFIG_HAS_ETH0
#define CONFIG_HAS_ETH1
#define CONFIG_PHY1_ADDR	0xc	/* EMAC1 PHY address		*/
#define CONFIG_PHY_CLK_FREQ    EMAC_STACR_CLK_66MHZ

/*
 * Commands additional to the ones defined in amcc-common.h
 */
#define CONFIG_CMD_CACHE
#define CONFIG_CMD_DATE
#define CONFIG_CMD_DTT
#undef CONFIG_CMD_EEPROM

/*
 * SDRAM configuration (please see cpu/ppc/sdram.[ch])
 */
#define CONFIG_SDRAM_BANK0	1	/* init onboard SDRAM bank 0 */

/* SDRAM timings used in datasheet */
#define CONFIG_SYS_SDRAM_CL            3	/* CAS latency */
#define CONFIG_SYS_SDRAM_tRP           20	/* PRECHARGE command period */
#define CONFIG_SYS_SDRAM_tRC           66	/* ACTIVE-to-ACTIVE command period */
#define CONFIG_SYS_SDRAM_tRCD          20	/* ACTIVE-to-READ delay */
#define CONFIG_SYS_SDRAM_tRFC		66	/* Auto refresh period */

/*
 * If CONFIG_SYS_EXT_SERIAL_CLOCK, then the UART divisor is 1.
 * If CONFIG_SYS_405_UART_ERRATA_59, then UART divisor is 31.
 * Otherwise, UART divisor is determined by CPU Clock and CONFIG_SYS_BASE_BAUD value.
 * The Linux BASE_BAUD define should match this configuration.
 *    baseBaud = cpuClock/(uartDivisor*16)
 * If CONFIG_SYS_405_UART_ERRATA_59 and 200MHz CPU clock,
 * set Linux BASE_BAUD to 403200.
 */
#define CONFIG_CONS_INDEX	1	/* Use UART0			*/
#define CONFIG_SYS_NS16550
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE	1
#define CONFIG_SYS_NS16550_CLK		get_serial_clock()

#undef  CONFIG_SYS_EXT_SERIAL_CLOCK           /* external serial clock */
#undef  CONFIG_SYS_405_UART_ERRATA_59         /* 405GP/CR Rev. D silicon */
#define CONFIG_SYS_BASE_BAUD		691200

/*
 * I2C stuff
 */
#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		100000

/* RTC */
#define CONFIG_RTC_DS1337
#define CONFIG_SYS_I2C_RTC_ADDR	0x68

/* Temp sensor/hwmon/dtt */
#define CONFIG_DTT_LM63		1	/* National LM63	*/
#define CONFIG_DTT_SENSORS	{ 0 }	/* Sensor addresses	*/
#define CONFIG_DTT_PWM_LOOKUPTABLE	\
		{ { 40, 10 }, { 50, 20 }, { 60, 40 } }
#define CONFIG_DTT_TACH_LIMIT	0xa10

/*
 * FLASH organization
 */
#define CONFIG_SYS_FLASH_CFI				/* The flash is CFI compatible	*/
#define CONFIG_FLASH_CFI_DRIVER			/* Use common CFI driver	*/

#define CONFIG_SYS_FLASH_BASE		0xFC000000
#define CONFIG_SYS_FLASH_BANKS_LIST	{ CONFIG_SYS_FLASH_BASE }

#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
#define CONFIG_SYS_MAX_FLASH_SECT	512	/* max number of sectors on one chip	*/

#define CONFIG_SYS_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/

#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1	/* use buffered writes (20x faster)	*/

#define CONFIG_SYS_FLASH_EMPTY_INFO		/* print 'E' for empty sector on flinfo */
#define CONFIG_SYS_FLASH_QUIET_TEST	1	/* don't warn upon unknown flash	*/

#ifdef CONFIG_ENV_IS_IN_FLASH
#define CONFIG_ENV_SECT_SIZE	0x20000	/* size of one complete sector		*/
#define CONFIG_ENV_ADDR		0xFFF00000
#define	CONFIG_ENV_SIZE		0x20000	/* Total Size of Environment Sector */

/* Address and size of Redundant Environment Sector	*/
#define CONFIG_ENV_ADDR_REDUND	0xFFF20000
#define CONFIG_ENV_SIZE_REDUND	(CONFIG_ENV_SIZE)
#endif

/*
 * PPC405 GPIO Configuration
 */
#define CONFIG_SYS_4xx_GPIO_TABLE { \
{ \
/* GPIO Core 0 */ \
{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO0	PerBLast   */ \
{ GPIO_BASE, GPIO_OUT, GPIO_SEL,  GPIO_OUT_NO_CHG }, /* GPIO1	TS1E	   */ \
{ GPIO_BASE, GPIO_OUT, GPIO_SEL,  GPIO_OUT_NO_CHG }, /* GPIO2	TS2E	   */ \
{ GPIO_BASE, GPIO_IN,  GPIO_SEL,  GPIO_OUT_NO_CHG }, /* GPIO3	TS1O	   */ \
{ GPIO_BASE, GPIO_OUT, GPIO_SEL,  GPIO_OUT_NO_CHG }, /* GPIO4	TS2O	   */ \
{ GPIO_BASE, GPIO_OUT, GPIO_SEL,  GPIO_OUT_1      }, /* GPIO5	TS3	   */ \
{ GPIO_BASE, GPIO_IN,  GPIO_SEL,  GPIO_OUT_NO_CHG }, /* GPIO6	TS4	   */ \
{ GPIO_BASE, GPIO_OUT, GPIO_SEL,  GPIO_OUT_NO_CHG }, /* GPIO7	TS5	   */ \
{ GPIO_BASE, GPIO_OUT, GPIO_SEL,  GPIO_OUT_NO_CHG }, /* GPIO8	TS6	   */ \
{ GPIO_BASE, GPIO_OUT, GPIO_SEL,  GPIO_OUT_NO_CHG }, /* GPIO9	TrcClk	   */ \
{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO10	PerCS1	   */ \
{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO11	PerCS2	   */ \
{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO12	PerCS3	   */ \
{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO13	PerCS4	   */ \
{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO14	PerAddr03  */ \
{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO15	PerAddr04  */ \
{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO16	PerAddr05  */ \
{ GPIO_BASE, GPIO_IN,  GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO17	IRQ0	   */ \
{ GPIO_BASE, GPIO_IN,  GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO18	IRQ1	   */ \
{ GPIO_BASE, GPIO_IN,  GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO19	IRQ2	   */ \
{ GPIO_BASE, GPIO_IN,  GPIO_SEL,  GPIO_OUT_NO_CHG }, /* GPIO20	IRQ3	   */ \
{ GPIO_BASE, GPIO_OUT, GPIO_SEL,  GPIO_OUT_NO_CHG }, /* GPIO21	IRQ4	   */ \
{ GPIO_BASE, GPIO_OUT, GPIO_SEL,  GPIO_OUT_NO_CHG }, /* GPIO22	IRQ5	   */ \
{ GPIO_BASE, GPIO_IN,  GPIO_SEL,  GPIO_OUT_NO_CHG }, /* GPIO23	IRQ6	   */ \
{ GPIO_BASE, GPIO_IN,  GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO24	UART0_DCD  */ \
{ GPIO_BASE, GPIO_IN,  GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO25	UART0_DSR  */ \
{ GPIO_BASE, GPIO_IN,  GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO26	UART0_RI   */ \
{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO27	UART0_DTR  */ \
{ GPIO_BASE, GPIO_IN,  GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO28	UART1_Rx   */ \
{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO29	UART1_Tx   */ \
{ GPIO_BASE, GPIO_OUT, GPIO_SEL,  GPIO_OUT_NO_CHG }, /* GPIO30	RejectPkt0 */ \
{ GPIO_BASE, GPIO_IN,  GPIO_SEL,  GPIO_OUT_NO_CHG }, /* GPIO31	RejectPkt1 */ \
} \
}

/*
 * Definitions for initial stack pointer and data area (in data cache)
 */
/* use on chip memory (OCM) for temperary stack until sdram is tested */
#define CONFIG_SYS_TEMP_STACK_OCM        1

/* On Chip Memory location */
#define CONFIG_SYS_OCM_DATA_ADDR	0xF8000000
#define CONFIG_SYS_OCM_DATA_SIZE	0x1000
#define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_OCM_DATA_ADDR /* inside of SDRAM		*/
#define CONFIG_SYS_INIT_RAM_SIZE	CONFIG_SYS_OCM_DATA_SIZE /* Size of used area in RAM	*/

#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET

/*
 * External Bus Controller (EBC) Setup
 */

/* Memory Bank 0 (NOR-FLASH) initialization                    */
#define CONFIG_SYS_EBC_PB0AP		0x92015480
#define CONFIG_SYS_EBC_PB0CR		0xFC0DA000  /* BAS=0xFC0,BS=64MB,BU=R/W,BW=16bit */

/* Memory Bank 1 (NVRAM) initialization                                        */
#define CONFIG_SYS_EBC_PB1AP		0x92015480
#define CONFIG_SYS_EBC_PB1CR		0xFB85A000  /* BAS=0xFF8,BS=4MB,BU=R/W,BW=8bit  */

/* Memory Bank 2 (FPGA) initialization                 */
#define CONFIG_SYS_FPGA0_BASE		0x7f100000
#define CONFIG_SYS_EBC_PB2AP		0x92015480
#define CONFIG_SYS_EBC_PB2CR		0x7f11a000  /* BAS=0x7f1,BS=1MB,BU=R/W,BW=16bit */

#define CONFIG_SYS_FPGA_BASE(k)		CONFIG_SYS_FPGA0_BASE

#define CONFIG_SYS_FPGA_COUNT		1

#define CONFIG_SYS_FPGA_PTR \
	{ (struct ihs_fpga *)CONFIG_SYS_FPGA0_BASE }

#define CONFIG_SYS_FPGA_COMMON

/* Memory Bank 3 (Latches) initialization                      */
#define CONFIG_SYS_LATCH_BASE		0x7f200000
#define CONFIG_SYS_EBC_PB3AP		0x92015480
#define CONFIG_SYS_EBC_PB3CR		0x7f21a000  /* BAS=0x7f2,BS=1MB,BU=R/W,BW=16bit */

#define CONFIG_SYS_LATCH0_RESET		0xffff
#define CONFIG_SYS_LATCH0_BOOT		0xffff
#define CONFIG_SYS_LATCH1_RESET		0xffbf
#define CONFIG_SYS_LATCH1_BOOT		0xffff

#endif	/* __CONFIG_H */