diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 790571b..3dcd6dd 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -91,6 +91,7 @@
 	armada-375-db.dtb			\
 	armada-388-clearfog.dtb			\
 	armada-388-gp.dtb			\
+	armada-388-helios4.dtb			\
 	armada-385-amc.dtb			\
 	armada-7040-db.dtb			\
 	armada-7040-db-nand.dtb			\
diff --git a/arch/arm/dts/armada-388-helios4.dts b/arch/arm/dts/armada-388-helios4.dts
new file mode 100644
index 0000000..049d322
--- /dev/null
+++ b/arch/arm/dts/armada-388-helios4.dts
@@ -0,0 +1,314 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Device Tree file for Helios4
+ * based on SolidRun Clearfog revision A1 rev 2.0 (88F6828)
+ *
+ *  Copyright (C) 2017 Aditya Prayoga <aditya@kobol.io>
+ *
+ */
+
+/dts-v1/;
+#include "armada-388.dtsi"
+#include "armada-38x-solidrun-microsom.dtsi"
+
+/ {
+	model = "Helios4";
+	compatible = "kobol,helios4", "marvell,armada388",
+		"marvell,armada385", "marvell,armada380";
+
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x80000000>; /* 2 GB */
+	};
+
+	aliases {
+		/* So that mvebu u-boot can update the MAC addresses */
+		ethernet1 = &eth0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	reg_12v: regulator-12v {
+		compatible = "regulator-fixed";
+		regulator-name = "power_brick_12V";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		regulator-always-on;
+	};
+
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		vin-supply = <&reg_12v>;
+	};
+
+	reg_5p0v_hdd: regulator-5v-hdd {
+		compatible = "regulator-fixed";
+		regulator-name = "5V_HDD";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		vin-supply = <&reg_12v>;
+	};
+
+	reg_5p0v_usb: regulator-5v-usb {
+		compatible = "regulator-fixed";
+		regulator-name = "USB-PWR";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-boot-on;
+		regulator-always-on;
+		enable-active-high;
+		gpio = <&expander0 6 GPIO_ACTIVE_HIGH>;
+		vin-supply = <&reg_12v>;
+	};
+
+	system-leds {
+		compatible = "gpio-leds";
+		status-led {
+			label = "helios4:green:status";
+			gpios = <&gpio0 24 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "heartbeat";
+			default-state = "on";
+		};
+
+		fault-led {
+			label = "helios4:red:fault";
+			gpios = <&gpio0 25 GPIO_ACTIVE_LOW>;
+			default-state = "keep";
+		};
+	};
+
+	io-leds {
+		compatible = "gpio-leds";
+		sata1-led {
+			label = "helios4:green:ata1";
+			gpios = <&gpio1 17 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "ata1";
+			default-state = "off";
+		};
+		sata2-led {
+			label = "helios4:green:ata2";
+			gpios = <&gpio1 18 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "ata2";
+			default-state = "off";
+		};
+		sata3-led {
+			label = "helios4:green:ata3";
+			gpios = <&gpio1 20 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "ata3";
+			default-state = "off";
+		};
+		sata4-led {
+			label = "helios4:green:ata4";
+			gpios = <&gpio1 21 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "ata4";
+			default-state = "off";
+		};
+		usb-led {
+			label = "helios4:green:usb";
+			gpios = <&gpio1 22 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "usb-host";
+			default-state = "off";
+		};
+	};
+
+	fan1: j10-pwm {
+		compatible = "pwm-fan";
+		pwms = <&gpio1 9 40000>;	/* Target freq:25 kHz */
+	};
+
+	fan2: j17-pwm {
+		compatible = "pwm-fan";
+		pwms = <&gpio1 23 40000>;	/* Target freq:25 kHz */
+	};
+
+	usb2_phy: usb2-phy {
+		compatible = "usb-nop-xceiv";
+		vbus-regulator = <&reg_5p0v_usb>;
+	};
+
+	usb3_phy: usb3-phy {
+		compatible = "usb-nop-xceiv";
+	};
+
+	soc {
+		internal-regs {
+			i2c@11000 {
+				clock-frequency = <400000>;
+				pinctrl-0 = <&i2c0_pins>;
+				pinctrl-names = "default";
+				status = "okay";
+
+				/*
+				 * PCA9655 GPIO expander, up to 1MHz clock.
+				 *  0-Board Revision bit 0 #
+				 *  1-Board Revision bit 1 #
+				 *  5-USB3 overcurrent
+				 *  6-USB3 power
+				 */
+				expander0: gpio-expander@20 {
+					/*
+					 * This is how it should be:
+					 * compatible = "onnn,pca9655",
+					 *	 "nxp,pca9555";
+					 * but you can't do this because of
+					 * the way I2C works.
+					 */
+					compatible = "nxp,pca9555";
+					gpio-controller;
+					#gpio-cells = <2>;
+					reg = <0x20>;
+					pinctrl-names = "default";
+					pinctrl-0 = <&pca0_pins>;
+					interrupt-parent = <&gpio0>;
+					interrupts = <23 IRQ_TYPE_EDGE_FALLING>;
+					interrupt-controller;
+					#interrupt-cells = <2>;
+
+					board_rev_bit_0 {
+						gpio-hog;
+						gpios = <0 GPIO_ACTIVE_LOW>;
+						input;
+						line-name = "board-rev-0";
+					};
+					board_rev_bit_1 {
+						gpio-hog;
+						gpios = <1 GPIO_ACTIVE_LOW>;
+						input;
+						line-name = "board-rev-1";
+					};
+					usb3_ilimit {
+						gpio-hog;
+						gpios = <5 GPIO_ACTIVE_HIGH>;
+						input;
+						line-name =
+						"usb-overcurrent-status";
+					};
+				};
+
+				temp_sensor: temp@4c {
+					compatible = "ti,lm75";
+					reg = <0x4c>;
+					vcc-supply = <&reg_3p3v>;
+				};
+			};
+
+			i2c@11100 {
+				/*
+				 * External I2C Bus for user peripheral
+				 */
+				clock-frequency = <400000>;
+				pinctrl-0 = <&helios_i2c1_pins>;
+				pinctrl-names = "default";
+				status = "okay";
+			};
+
+			sata@a8000 {
+				status = "okay";
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				sata0: sata-port@0 {
+					reg = <0>;
+				};
+
+				sata1: sata-port@1 {
+					reg = <1>;
+				};
+			};
+
+			sata@e0000 {
+				status = "okay";
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				sata2: sata-port@0 {
+					reg = <0>;
+				};
+
+				sata3: sata-port@1 {
+					reg = <1>;
+				};
+			};
+
+			spi@10680 {
+				pinctrl-0 = <&spi1_pins
+					     &microsom_spi1_cs_pins>;
+				pinctrl-names = "default";
+				status = "okay";
+			};
+
+			sdhci@d8000 {
+				bus-width = <4>;
+				cd-gpios = <&gpio0 20 GPIO_ACTIVE_LOW>;
+				no-1-8-v;
+				pinctrl-0 = <&helios_sdhci_pins
+					     &helios_sdhci_cd_pins>;
+				pinctrl-names = "default";
+				status = "okay";
+				vmmc = <&reg_3p3v>;
+				wp-inverted;
+			};
+
+			usb@58000 {
+				usb-phy = <&usb2_phy>;
+				status = "okay";
+			};
+
+			usb3@f0000 {
+				status = "okay";
+			};
+
+			usb3@f8000 {
+				status = "okay";
+			};
+
+			pinctrl@18000 {
+				pca0_pins: pca0-pins {
+					marvell,pins = "mpp23";
+					marvell,function = "gpio";
+				};
+				microsom_phy0_int_pins: microsom-phy0-int-pins {
+					marvell,pins = "mpp18";
+					marvell,function = "gpio";
+				};
+				helios_i2c1_pins: i2c1-pins {
+					marvell,pins = "mpp26", "mpp27";
+					marvell,function = "i2c1";
+				};
+				helios_sdhci_cd_pins: helios-sdhci-cd-pins {
+					marvell,pins = "mpp20";
+					marvell,function = "gpio";
+				};
+				helios_sdhci_pins: helios-sdhci-pins {
+					marvell,pins = "mpp21", "mpp28",
+						       "mpp37", "mpp38",
+						       "mpp39", "mpp40";
+					marvell,function = "sd0";
+				};
+				helios_led_pins: helios-led-pins {
+					marvell,pins = "mpp24", "mpp25",
+						       "mpp49", "mpp50",
+						       "mpp52", "mpp53",
+						       "mpp54";
+					marvell,function = "gpio";
+				};
+				helios_fan_pins: helios-fan-pins {
+					marvell,pins = "mpp41", "mpp43",
+						       "mpp48", "mpp55";
+					marvell,function = "gpio";
+				};
+				microsom_spi1_cs_pins: spi1-cs-pins {
+					marvell,pins = "mpp59";
+					marvell,function = "spi1";
+				};
+			};
+		};
+	};
+};
diff --git a/arch/arm/dts/armada-38x-solidrun-microsom.dtsi b/arch/arm/dts/armada-38x-solidrun-microsom.dtsi
new file mode 100644
index 0000000..a262722
--- /dev/null
+++ b/arch/arm/dts/armada-38x-solidrun-microsom.dtsi
@@ -0,0 +1,101 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Device Tree file for SolidRun Armada 38x Microsom
+ *
+ *  Copyright (C) 2015 Russell King
+ *
+ * This board is in development; the contents of this file work with
+ * the A1 rev 2.0 of the board, which does not represent final
+ * production board.  Things will change, don't expect this file to
+ * remain compatible info the future.
+ */
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x10000000>; /* 256 MB */
+	};
+
+	soc {
+		ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000
+			  MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000
+			  MBUS_ID(0x09, 0x19) 0 0xf1100000 0x10000
+			  MBUS_ID(0x09, 0x15) 0 0xf1110000 0x10000
+			  MBUS_ID(0x0c, 0x04) 0 0xf1200000 0x100000>;
+
+		internal-regs {
+			rtc@a3800 {
+				/*
+				 * If the rtc doesn't work, run "date reset"
+				 * twice in u-boot.
+				 */
+				status = "okay";
+			};
+		};
+	};
+};
+
+&eth0 {
+	/* ethernet@70000 */
+	mac-address = [00 50 43 02 02 01];
+	pinctrl-0 = <&ge0_rgmii_pins>;
+	pinctrl-names = "default";
+	phy = <&phy_dedicated>;
+	phy-mode = "rgmii-id";
+	status = "okay";
+};
+
+&mdio {
+	/*
+	 * Add the phy clock here, so the phy can be accessed to read its
+	 * IDs prior to binding with the driver.
+	 */
+	pinctrl-0 = <&mdio_pins &microsom_phy_clk_pins>;
+	pinctrl-names = "default";
+
+	phy_dedicated: ethernet-phy@0 {
+		/*
+		 * Annoyingly, the marvell phy driver configures the LED
+		 * register, rather than preserving reset-loaded setting.
+		 * We undo that rubbish here.
+		 */
+		marvell,reg-init = <3 16 0 0x101e>;
+		reg = <0>;
+	};
+};
+
+&pinctrl {
+	microsom_phy_clk_pins: microsom-phy-clk-pins {
+		marvell,pins = "mpp45";
+		marvell,function = "ref";
+	};
+	/* Optional eMMC */
+	microsom_sdhci_pins: microsom-sdhci-pins {
+		marvell,pins = "mpp21", "mpp28", "mpp37",
+			       "mpp38", "mpp39", "mpp40";
+		marvell,function = "sd0";
+	};
+};
+
+&spi1 {
+	/* The microsom has an optional W25Q32 on board, connected to CS0 */
+	pinctrl-0 = <&spi1_pins>;
+
+	w25q32: spi-flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "w25q32", "jedec,spi-nor";
+		reg = <0>; /* Chip select 0 */
+		spi-max-frequency = <3000000>;
+		status = "disabled";
+	};
+};
+
+&uart0 {
+	pinctrl-0 = <&uart0_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+	u-boot,dm-pre-reloc;
+};
diff --git a/arch/arm/mach-mvebu/Kconfig b/arch/arm/mach-mvebu/Kconfig
index f431cff..5415b5a 100644
--- a/arch/arm/mach-mvebu/Kconfig
+++ b/arch/arm/mach-mvebu/Kconfig
@@ -75,6 +75,10 @@
 	bool "Support ClearFog"
 	select 88F6820
 
+config TARGET_HELIOS4
+	bool "Support Helios4"
+	select 88F6820
+
 config TARGET_MVEBU_ARMADA_37XX
 	bool "Support Armada 37xx platforms"
 	select ARMADA_3700
@@ -132,6 +136,7 @@
 
 config SYS_BOARD
 	default "clearfog" if TARGET_CLEARFOG
+	default "helios4" if TARGET_HELIOS4
 	default "mvebu_armada-37xx" if TARGET_MVEBU_ARMADA_37XX
 	default "db-88f6720" if TARGET_DB_88F6720
 	default "db-88f6820-gp" if TARGET_DB_88F6820_GP
@@ -146,6 +151,7 @@
 
 config SYS_CONFIG_NAME
 	default "clearfog" if TARGET_CLEARFOG
+	default "helios4" if TARGET_HELIOS4
 	default "mvebu_armada-37xx" if TARGET_MVEBU_ARMADA_37XX
 	default "db-88f6720" if TARGET_DB_88F6720
 	default "db-88f6820-gp" if TARGET_DB_88F6820_GP
@@ -166,6 +172,7 @@
 	default "Marvell" if TARGET_DB_88F6820_AMC
 	default "Marvell" if TARGET_MVEBU_ARMADA_8K
 	default "solidrun" if TARGET_CLEARFOG
+	default "kobol" if TARGET_HELIOS4
 	default "Synology" if TARGET_DS414
 	default "CZ.NIC" if TARGET_TURRIS_OMNIA
 	default "CZ.NIC" if TARGET_TURRIS_MOX
diff --git a/board/kobol/helios4/MAINTAINERS b/board/kobol/helios4/MAINTAINERS
new file mode 100644
index 0000000..c9610de
--- /dev/null
+++ b/board/kobol/helios4/MAINTAINERS
@@ -0,0 +1,6 @@
+HELIOS4 BOARD
+M:	Dennis Gilmore <dgilmore@redhat.com>
+S:	Maintained
+F:	board/kobol/helios4/
+F:	include/configs/helios4.h
+F:	configs/helios4_defconfig
diff --git a/board/kobol/helios4/Makefile b/board/kobol/helios4/Makefile
new file mode 100644
index 0000000..63f0796
--- /dev/null
+++ b/board/kobol/helios4/Makefile
@@ -0,0 +1,5 @@
+# SPDX-License-Identifier: GPL-2.0+
+#
+# Copyright (C) 2018 Dennis Gilmore <dgilmore@redhat.com>
+
+obj-y	:= helios4.o
diff --git a/board/kobol/helios4/README b/board/kobol/helios4/README
new file mode 100644
index 0000000..749f048
--- /dev/null
+++ b/board/kobol/helios4/README
@@ -0,0 +1,46 @@
+Update from original Marvell U-Boot to mainline U-Boot:
+-------------------------------------------------------
+
+Generate the U-Boot image with these commands:
+
+$ make helios4_defconfig
+$ make
+
+The resulting image including the SPL binary with the
+full DDR setup is "u-boot-spl.kwb".
+
+Now all you need to do is copy this image on a SD card.
+For example with this command:
+
+$ sudo dd if=u-boot-spl.kwb of=/dev/sdX bs=512 seek=1
+
+Please use the correct device node for your setup instead
+of "/dev/sdX" here!
+
+Boot selection:
+---------------
+
+Before powering up the board, boot selection should be done via the SW1 dip
+switch (0: OFF, 1: ON):
+
+ - SPI:     00010
+ - SD/eMMC: 00111
+ - SATA1:   11100
+ - UART:    11110
+
+Boot from UART:
+---------------
+
+Connect the on-board micro-USB (CF Pro: CON11, CF Base: CON5)
+to your host.
+
+Set the SW1 DIP switches to UART boot (see above).
+
+Run the following command to initiate U-Boot download:
+
+  ./tools/kwboot -p -b u-boot-spl.kwb /dev/ttyUSBX
+
+Use the correct UART device node for /dev/ttyUSBX.
+
+When download finishes start your favorite terminal emulator
+on /dev/ttyUSBX.
diff --git a/board/kobol/helios4/helios4.c b/board/kobol/helios4/helios4.c
new file mode 100644
index 0000000..3416783
--- /dev/null
+++ b/board/kobol/helios4/helios4.c
@@ -0,0 +1,163 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2018 Dennis Gilmore <dgilmore@redhat.com>
+ *  based on board/solidrun/clearfog/clearfog.c
+ */
+
+#include <common.h>
+#include <i2c.h>
+#include <miiphy.h>
+#include <netdev.h>
+#include <asm/io.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/soc.h>
+
+#include "../drivers/ddr/marvell/a38x/ddr3_init.h"
+#include <../serdes/a38x/high_speed_env_spec.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define ETH_PHY_CTRL_REG		0
+#define ETH_PHY_CTRL_POWER_DOWN_BIT	11
+#define ETH_PHY_CTRL_POWER_DOWN_MASK	BIT(ETH_PHY_CTRL_POWER_DOWN_BIT)
+
+/*
+ * Those values and defines are taken from the Marvell U-Boot version
+ * "u-boot-2013.01-15t1-helios4" as well as the upstream config for clearfog
+ */
+#define BOARD_GPP_OUT_ENA_LOW	0xffffffff
+#define BOARD_GPP_OUT_ENA_MID	0xffffffff
+
+#define BOARD_GPP_OUT_VAL_LOW	0x0
+#define BOARD_GPP_OUT_VAL_MID	0x0
+#define BOARD_GPP_POL_LOW	0x0
+#define BOARD_GPP_POL_MID	0x0
+
+/* IO expander on Marvell GP board includes e.g. fan enabling */
+struct marvell_io_exp {
+	u8 addr;
+	u8 val;
+};
+
+static struct marvell_io_exp io_exp[] = {
+	{6, 0xf9},
+	{2, 0x46}, /* Assert reset signals and enable USB3 current limiter */
+	{6, 0xb9}
+};
+
+static struct serdes_map board_serdes_map[] = {
+	{SATA0, SERDES_SPEED_6_GBPS, SERDES_DEFAULT_MODE, 0, 0},
+	{USB3_HOST0, SERDES_SPEED_5_GBPS, SERDES_DEFAULT_MODE, 0, 0},
+	{SATA1, SERDES_SPEED_6_GBPS, SERDES_DEFAULT_MODE, 0, 0},
+	{SATA3, SERDES_SPEED_6_GBPS, SERDES_DEFAULT_MODE, 0, 0},
+	{SATA2, SERDES_SPEED_6_GBPS, SERDES_DEFAULT_MODE, 0, 0},
+	{USB3_HOST1, SERDES_SPEED_5_GBPS, SERDES_DEFAULT_MODE, 0, 0},
+};
+
+int hws_board_topology_load(struct serdes_map **serdes_map_array, u8 *count)
+{
+	*serdes_map_array = board_serdes_map;
+	*count = ARRAY_SIZE(board_serdes_map);
+	return 0;
+}
+
+/*
+ * Define the DDR layout / topology here in the board file. This will
+ * be used by the DDR3 init code in the SPL U-Boot version to configure
+ * the DDR3 controller.
+ */
+static struct mv_ddr_topology_map board_topology_map = {
+	DEBUG_LEVEL_ERROR,
+	0x1, /* active interfaces */
+	/* cs_mask, mirror, dqs_swap, ck_swap X PUPs */
+	{ { { {0x1, 0, 0, 0},
+	      {0x1, 0, 0, 0},
+	      {0x1, 0, 0, 0},
+	      {0x1, 0, 0, 0},
+	      {0x1, 0, 0, 0} },
+	    SPEED_BIN_DDR_1600K,	/* speed_bin */
+	    MV_DDR_DEV_WIDTH_16BIT,	/* memory_width */
+	    MV_DDR_DIE_CAP_8GBIT,	/* mem_size */
+	    DDR_FREQ_800,		/* frequency */
+	    0, 0,			/* cas_wl cas_l */
+	    MV_DDR_TEMP_LOW,		/* temperature */
+	    MV_DDR_TIM_DEFAULT} },	/* timing */
+	BUS_MASK_32BIT_ECC,		/* Busses mask */
+	MV_DDR_CFG_DEFAULT,		/* ddr configuration data source */
+	{ {0} },			/* raw spd data */
+	{0}				/* timing parameters */
+};
+
+struct mv_ddr_topology_map *mv_ddr_topology_map_get(void)
+{
+	/* Return the board topology as defined in the board code */
+	return &board_topology_map;
+}
+
+int board_early_init_f(void)
+{
+	/* Configure MPP */
+	writel(0x11111111, MVEBU_MPP_BASE + 0x00);
+	writel(0x11111111, MVEBU_MPP_BASE + 0x04);
+	writel(0x10400011, MVEBU_MPP_BASE + 0x08);
+	writel(0x22043333, MVEBU_MPP_BASE + 0x0c);
+	writel(0x44400002, MVEBU_MPP_BASE + 0x10);
+	writel(0x41144004, MVEBU_MPP_BASE + 0x14);
+	writel(0x40333333, MVEBU_MPP_BASE + 0x18);
+	writel(0x00004444, MVEBU_MPP_BASE + 0x1c);
+
+	/* Set GPP Out value */
+	writel(BOARD_GPP_OUT_VAL_LOW, MVEBU_GPIO0_BASE + 0x00);
+	writel(BOARD_GPP_OUT_VAL_MID, MVEBU_GPIO1_BASE + 0x00);
+
+	/* Set GPP Polarity */
+	writel(BOARD_GPP_POL_LOW, MVEBU_GPIO0_BASE + 0x0c);
+	writel(BOARD_GPP_POL_MID, MVEBU_GPIO1_BASE + 0x0c);
+
+	/* Set GPP Out Enable */
+	writel(BOARD_GPP_OUT_ENA_LOW, MVEBU_GPIO0_BASE + 0x04);
+	writel(BOARD_GPP_OUT_ENA_MID, MVEBU_GPIO1_BASE + 0x04);
+
+	return 0;
+}
+
+int board_init(void)
+{
+	int i;
+
+	/* Address of boot parameters */
+	gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;
+
+	/* Init I2C IO expanders */
+	for (i = 0; i < ARRAY_SIZE(io_exp); i++) {
+		struct udevice *dev;
+		int ret;
+
+		ret = i2c_get_chip_for_busnum(0, io_exp[i].addr, 1, &dev);
+		if (ret) {
+			printf("Cannot find I2C: %d\n", ret);
+			return 0;
+		}
+
+		ret = dm_i2c_write(dev, io_exp[i].val, &io_exp[i].val, 1);
+		if (ret) {
+			printf("Failed to set IO expander via I2C\n");
+			return -EIO;
+		}
+	}
+
+	return 0;
+}
+
+int checkboard(void)
+{
+	puts("Board: Helios4\n");
+
+	return 0;
+}
+
+int board_eth_init(bd_t *bis)
+{
+	cpu_eth_init(bis); /* Built in controller(s) come first */
+	return pci_eth_init(bis);
+}
diff --git a/board/kobol/helios4/kwbimage.cfg b/board/kobol/helios4/kwbimage.cfg
new file mode 100644
index 0000000..035063b
--- /dev/null
+++ b/board/kobol/helios4/kwbimage.cfg
@@ -0,0 +1,13 @@
+# SPDX-License-Identifier: GPL-2.0+
+#
+# Copyright (C) 2015 Stefan Roese <sr@denx.de>
+#
+
+# Armada 38x use version 1 image format
+VERSION		1
+
+# Boot Media configurations
+BOOT_FROM	sdio
+
+# Binary Header (bin_hdr) with DDR3 training code
+BINARY spl/u-boot-spl-dtb.bin 0000005b 00000068
diff --git a/configs/helios4_defconfig b/configs/helios4_defconfig
new file mode 100644
index 0000000..b724285
--- /dev/null
+++ b/configs/helios4_defconfig
@@ -0,0 +1,58 @@
+CONFIG_ARM=y
+CONFIG_ARCH_MVEBU=y
+CONFIG_SYS_TEXT_BASE=0x00800000
+CONFIG_SPL_LIBCOMMON_SUPPORT=y
+CONFIG_SPL_LIBGENERIC_SUPPORT=y
+CONFIG_SYS_MALLOC_F_LEN=0x2000
+CONFIG_TARGET_HELIOS4=y
+CONFIG_SPL_MMC_SUPPORT=y
+CONFIG_SPL_SERIAL_SUPPORT=y
+CONFIG_SPL_LIBDISK_SUPPORT=y
+CONFIG_SPL=y
+CONFIG_DEFAULT_DEVICE_TREE="armada-388-helios4"
+CONFIG_DEBUG_UART=y
+CONFIG_DISTRO_DEFAULTS=y
+CONFIG_BOOTDELAY=3
+CONFIG_SYS_CONSOLE_INFO_QUIET=y
+# CONFIG_DISPLAY_BOARDINFO is not set
+CONFIG_DISPLAY_BOARDINFO_LATE=y
+CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x141
+CONFIG_SPL_I2C_SUPPORT=y
+# CONFIG_CMD_FLASH is not set
+CONFIG_CMD_I2C=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_PCI=y
+CONFIG_CMD_SF=y
+CONFIG_CMD_SPI=y
+CONFIG_CMD_USB=y
+# CONFIG_CMD_SETEXPR is not set
+CONFIG_CMD_TFTPPUT=y
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_TIME=y
+# CONFIG_SPL_PARTITION_UUIDS is not set
+CONFIG_ENV_IS_IN_MMC=y
+CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_SPL_OF_TRANSLATE=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_SDMA=y
+CONFIG_MMC_SDHCI_MV=y
+CONFIG_AHCI=y
+CONFIG_SCSI_AHCI=y
+CONFIG_SCSI=y
+CONFIG_SPI_FLASH=y
+CONFIG_SPI_FLASH_BAR=y
+CONFIG_SPI_FLASH_WINBOND=y
+CONFIG_SPI_FLASH_MTD=y
+CONFIG_PHY_GIGE=y
+CONFIG_MVNETA=y
+CONFIG_PCI=y
+CONFIG_DEBUG_UART_BASE=0xd0012000
+CONFIG_DEBUG_UART_CLOCK=250000000
+CONFIG_DEBUG_UART_SHIFT=2
+CONFIG_SYS_NS16550=y
+CONFIG_KIRKWOOD_SPI=y
+CONFIG_USB=y
+CONFIG_DM_USB=y
+CONFIG_DM_I2C=y
+CONFIG_USB_XHCI_HCD=y
+CONFIG_USB_STORAGE=y
diff --git a/include/configs/helios4.h b/include/configs/helios4.h
new file mode 100644
index 0000000..ce912ea
--- /dev/null
+++ b/include/configs/helios4.h
@@ -0,0 +1,172 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Copyright (C) 2018 Dennis Gilmore <dgilmore@redhat.com>
+ */
+
+#ifndef _CONFIG_HELIOS4_H
+#define _CONFIG_HELIOS4_H
+
+/*
+ * High Level Configuration Options (easy to change)
+ */
+
+/*
+ * TEXT_BASE needs to be below 16MiB, since this area is scrubbed
+ * for DDR ECC byte filling in the SPL before loading the main
+ * U-Boot into it.
+ */
+#define CONFIG_SYS_TCLK		250000000	/* 250MHz */
+
+/*
+ * Commands configuration
+ */
+
+/* SPI NOR flash default params, used by sf commands */
+#define CONFIG_SF_DEFAULT_BUS		1
+
+/*
+ * SDIO/MMC Card Configuration
+ */
+#define CONFIG_SYS_MMC_BASE		MVEBU_SDIO_BASE
+
+/* USB/EHCI configuration */
+#define CONFIG_EHCI_IS_TDI
+
+#define CONFIG_ENV_MIN_ENTRIES		128
+
+/*
+ * SATA/SCSI/AHCI configuration
+ */
+#define CONFIG_SCSI_AHCI_PLAT
+#define CONFIG_SYS_SCSI_MAX_SCSI_ID     2
+#define CONFIG_SYS_SCSI_MAX_LUN         2
+#define CONFIG_SYS_SCSI_MAX_DEVICE      (CONFIG_SYS_SCSI_MAX_SCSI_ID * \
+					CONFIG_SYS_SCSI_MAX_LUN)
+
+/* Environment in MMC */
+#define CONFIG_SYS_MMC_ENV_DEV		0
+#define CONFIG_ENV_SECT_SIZE		0x200
+#define CONFIG_ENV_SIZE			0x10000
+/*
+ * For SD - reserve 1 LBA for MBR + 1M for u-boot image. The MMC/eMMC
+ * boot image starts @ LBA-0.
+ * As result in MMC/eMMC case it will be a 1 sector gap between u-boot
+ * image and environment
+ */
+#define CONFIG_ENV_OFFSET		0xf0000
+#define CONFIG_ENV_ADDR			CONFIG_ENV_OFFSET
+
+#define CONFIG_PHY_MARVELL		/* there is a marvell phy */
+#define PHY_ANEG_TIMEOUT	8000	/* PHY needs a longer aneg time */
+
+/* PCIe support */
+#ifndef CONFIG_SPL_BUILD
+#define CONFIG_PCI_MVEBU
+#define CONFIG_PCI_SCAN_SHOW
+#endif
+
+/* Keep device tree and initrd in lower memory so the kernel can access them */
+#define RELOCATION_LIMITS_ENV_SETTINGS	\
+	"fdt_high=0x10000000\0"		\
+	"initrd_high=0x10000000\0"
+
+/* SPL */
+/*
+ * Select the boot device here
+ *
+ * Currently supported are:
+ * SPL_BOOT_SPI_NOR_FLASH	- Booting via SPI NOR flash
+ * SPL_BOOT_SDIO_MMC_CARD	- Booting via SDIO/MMC card (partition 1)
+ */
+#define SPL_BOOT_SPI_NOR_FLASH		1
+#define SPL_BOOT_SDIO_MMC_CARD		2
+#define CONFIG_SPL_BOOT_DEVICE		SPL_BOOT_SDIO_MMC_CARD
+
+/* Defines for SPL */
+#define CONFIG_SPL_SIZE			(140 << 10)
+#define CONFIG_SPL_TEXT_BASE		0x40000030
+#define CONFIG_SPL_MAX_SIZE		(CONFIG_SPL_SIZE - 0x0030)
+
+#define CONFIG_SPL_BSS_START_ADDR	(0x40000000 + CONFIG_SPL_SIZE)
+#define CONFIG_SPL_BSS_MAX_SIZE		(16 << 10)
+
+#ifdef CONFIG_SPL_BUILD
+#define CONFIG_SYS_MALLOC_SIMPLE
+#endif
+
+#define CONFIG_SPL_STACK		(0x40000000 + ((192 - 16) << 10))
+#define CONFIG_SPL_BOOTROM_SAVE		(CONFIG_SPL_STACK + 4)
+
+#if CONFIG_SPL_BOOT_DEVICE == SPL_BOOT_SPI_NOR_FLASH
+/* SPL related SPI defines */
+#define CONFIG_SYS_SPI_U_BOOT_OFFS	0x20000
+#define CONFIG_SYS_U_BOOT_OFFS		CONFIG_SYS_SPI_U_BOOT_OFFS
+#endif
+
+#if CONFIG_SPL_BOOT_DEVICE == SPL_BOOT_SDIO_MMC_CARD
+/* SPL related MMC defines */
+#define CONFIG_SYS_MMC_U_BOOT_OFFS		(160 << 10)
+#define CONFIG_SYS_U_BOOT_OFFS			CONFIG_SYS_MMC_U_BOOT_OFFS
+#ifdef CONFIG_SPL_BUILD
+#define CONFIG_FIXED_SDHCI_ALIGNED_BUFFER	0x00180000	/* in SDRAM */
+#endif
+#endif
+/*
+ * mv-common.h should be defined after CMD configs since it used them
+ * to enable certain macros
+ */
+#include "mv-common.h"
+
+/* Include the common distro boot environment */
+#ifndef CONFIG_SPL_BUILD
+
+#ifdef CONFIG_MMC
+#define BOOT_TARGET_DEVICES_MMC(func) func(MMC, mmc, 0)
+#else
+#define BOOT_TARGET_DEVICES_MMC(func)
+#endif
+
+#ifdef CONFIG_USB_STORAGE
+#define BOOT_TARGET_DEVICES_USB(func) func(USB, usb, 0)
+#else
+#define BOOT_TARGET_DEVICES_USB(func)
+#endif
+
+#ifdef CONFIG_SATA
+#define BOOT_TARGET_DEVICES_SATA(func) func(SATA, sata, 0)
+#else
+#define BOOT_TARGET_DEVICES_SATA(func)
+#endif
+
+#define BOOT_TARGET_DEVICES(func) \
+	BOOT_TARGET_DEVICES_MMC(func) \
+	BOOT_TARGET_DEVICES_USB(func) \
+	BOOT_TARGET_DEVICES_SATA(func) \
+	func(PXE, pxe, na) \
+	func(DHCP, dhcp, na)
+
+#define KERNEL_ADDR_R	__stringify(0x800000)
+#define FDT_ADDR_R	__stringify(0x100000)
+#define RAMDISK_ADDR_R	__stringify(0x1800000)
+#define SCRIPT_ADDR_R	__stringify(0x200000)
+#define PXEFILE_ADDR_R	__stringify(0x300000)
+
+#define LOAD_ADDRESS_ENV_SETTINGS \
+	"kernel_addr_r=" KERNEL_ADDR_R "\0" \
+	"fdt_addr_r=" FDT_ADDR_R "\0" \
+	"ramdisk_addr_r=" RAMDISK_ADDR_R "\0" \
+	"scriptaddr=" SCRIPT_ADDR_R "\0" \
+	"pxefile_addr_r=" PXEFILE_ADDR_R "\0"
+
+#include <config_distro_bootcmd.h>
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+	RELOCATION_LIMITS_ENV_SETTINGS \
+	LOAD_ADDRESS_ENV_SETTINGS \
+	"fdtfile=" CONFIG_DEFAULT_DEVICE_TREE ".dtb\0" \
+	"console=ttyS0,115200\0" \
+	BOOTENV
+
+#endif /* CONFIG_SPL_BUILD */
+
+#endif /* _CONFIG_HELIOS4_H */