powerpc/t1024qds: Add T1024 QDS board support

T1024QDS is a high-performance computing evaluation, development and
test platform for T1024 QorIQ Power Architecture processor.

T1024QDS board Overview
-----------------------
- T1024 SoC integrating two 64-bit e5500 cores up to 1.4GHz
- CoreNet fabric supporting coherent and noncoherent transactions with
  prioritization and bandwidth allocation
- 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving support
- Accelerator: DPAA components consist of FMan, BMan, QMan, DCE and SEC
- Ethernet interfaces:
  - Two 10M/100M/1G RGMII ports on-board
  - Three 1G/2.5Gbps SGMII ports
  - Four 1Gbps QSGMII ports
  - one 10Gbps XFI or 10Base-KR interface
- SerDes: 4 lanes up to 10.3125GHz Supporting SGMII/QSGMII, XFI, PCIe, SATA and Aurora
- PCIe: Three PCI Express controllers with five PCIe slots.
- IFC: 128MB NOR Flash, 2GB NAND Flash, PromJet debug port and Qixis FPGA
- Video: DIU supports video up to 1280x1024x32 bpp.
  - Chrontel CH7201 for HDMI connection.
  - TI DS90C387R for direct LCD connection.
  - Raw (not encoded) video connector for testing or other encoders.
- QUICC Engine block
  - 32-bit RISC controller for flexible support of the communications peripherals
  - Serial DMA channel for receive and transmit on all serial channels
  - Two universal communication controllers, supporting TDM, HDLC, and UART
- Deep Sleep power implementaion (wakeup from GPIO/Timer/Ethernet/USB)
- eSPI: Three SPI flash devices.
- SATA: one SATA 2.O.
- USB: Two USB2.0 ports with internal PHY (one Type-A + one micro Type mini-AB)
- eSDHC: Support SD, SDHC, SDXC and MMC/eMMC.
- I2C: Four I2C controllers.
- UART: Two UART on board.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
[York Sun: Fix ft_board_setup() type, fix MAINTAINERS for SECURE_BOOT
	   Fix Kconfig by adding SUPPORT_SPL]
Reviewed-by: York Sun <yorksun@freescale.com>
diff --git a/board/freescale/t102xqds/Kconfig b/board/freescale/t102xqds/Kconfig
new file mode 100644
index 0000000..4d17798
--- /dev/null
+++ b/board/freescale/t102xqds/Kconfig
@@ -0,0 +1,12 @@
+if TARGET_T102XQDS
+
+config SYS_BOARD
+	default "t102xqds"
+
+config SYS_VENDOR
+	default "freescale"
+
+config SYS_CONFIG_NAME
+	default "T102xQDS"
+
+endif
diff --git a/board/freescale/t102xqds/MAINTAINERS b/board/freescale/t102xqds/MAINTAINERS
new file mode 100644
index 0000000..1ffccc4
--- /dev/null
+++ b/board/freescale/t102xqds/MAINTAINERS
@@ -0,0 +1,12 @@
+T102XQDS BOARD
+M:	Shengzhou Liu  <Shengzhou.Liu@freescale.com>
+S:	Maintained
+F:	board/freescale/t102xqds/
+F:	include/configs/T102xQDS.h
+F:	configs/T1024QDS_defconfig
+F:	configs/T1024QDS_NAND_defconfig
+F:	configs/T1024QDS_SDCARD_defconfig
+F:	configs/T1024QDS_SPIFLASH_defconfig
+F:	configs/T1024QDS_D4_defconfig
+F:	configs/T1024QDS_SECURE_BOOT_defconfig
+F:	configs/T1024QDS_D4_SECURE_BOOT_defconfig
diff --git a/board/freescale/t102xqds/Makefile b/board/freescale/t102xqds/Makefile
new file mode 100644
index 0000000..d94f230
--- /dev/null
+++ b/board/freescale/t102xqds/Makefile
@@ -0,0 +1,17 @@
+#
+# Copyright 2014 Freescale Semiconductor, Inc.
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+ifdef CONFIG_SPL_BUILD
+obj-y += spl.o
+else
+obj-y	+= t102xqds.o
+obj-y	+= eth_t102xqds.o
+obj-$(CONFIG_PCI) += pci.o
+obj-$(CONFIG_FSL_DIU_FB) += ../t1040qds/diu.o
+endif
+obj-y   += ddr.o
+obj-y   += law.o
+obj-y   += tlb.o
diff --git a/board/freescale/t102xqds/README b/board/freescale/t102xqds/README
new file mode 100644
index 0000000..bb0f280
--- /dev/null
+++ b/board/freescale/t102xqds/README
@@ -0,0 +1,328 @@
+T1024 SoC Overview
+------------------
+The T1024/T1023 dual core and T1014/T1013 single core QorIQ communication processor
+combines two or one 64-bit Power Architecture e5500 core respectively with high
+performance datapath acceleration logic, and network peripheral bus interfaces
+required for networking and telecommunications. This processor can be used in
+applications such as enterprise WLAN access points, routers, switches, firewall
+and other packet processing intensive small enterprise and branch office appliances,
+and general-purpose embedded computing. Its high level of integration offers
+significant performance benefits and greatly helps to simplify board design.
+
+
+The T1024 SoC includes the following function and features:
+- two e5500 cores, each with a private 256 KB L2 cache
+  - Up to 1.4 GHz with 64-bit ISA support (Power Architecture v2.06-compliant)
+  - Three levels of instructions: User, supervisor, and hypervisor
+  - Independent boot and reset
+  - Secure boot capability
+- 256 KB shared L3 CoreNet platform cache (CPC)
+- Interconnect CoreNet platform
+  - CoreNet coherency manager supporting coherent and noncoherent transactions
+    with prioritization and bandwidth allocation amongst CoreNet endpoints
+  - 150 Gbps coherent read bandwidth
+- 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving support
+- Data Path Acceleration Architecture (DPAA) incorporating acceleration for the following functions:
+  - Packet parsing, classification, and distribution
+  - Queue management for scheduling, packet sequencing, and congestion management
+  - Cryptography Acceleration (SEC 5.x)
+  - IEEE 1588 support
+  - Hardware buffer management for buffer allocation and deallocation
+  - MACSEC on DPAA-based Ethernet ports
+- Ethernet interfaces
+  - Four 1 Gbps Ethernet controllers
+- Parallel Ethernet interfaces
+  - Two RGMII interfaces
+- High speed peripheral interfaces
+  - Three PCI Express 2.0 controllers/ports running at up to 5 GHz
+  - One SATA controller supporting 1.5 and 3.0 Gb/s operation
+  - One QSGMII interface
+  - Four SGMII interface supporting 1000 Mbps
+  - Three SGMII interfaces supporting up to 2500 Mbps
+  - 10GbE XFI or 10Base-KR interface
+- Additional peripheral interfaces
+  - Two USB 2.0 controllers with integrated PHY
+  - SD/eSDHC/eMMC
+  - eSPI controller
+  - Four I2C controllers
+  - Four UARTs
+  - Four GPIO controllers
+  - Integrated flash controller (IFC)
+  - LCD interface (DIU) with 12 bit dual data rate
+- Multicore programmable interrupt controller (PIC)
+- Two 8-channel DMA engines
+- Single source clocking implementation
+- Deep Sleep power implementaion (wakeup from GPIO/Timer/Ethernet/USB)
+- QUICC Engine block
+  - 32-bit RISC controller for flexible support of the communications peripherals
+  - Serial DMA channel for receive and transmit on all serial channels
+  - Two universal communication controllers, supporting TDM, HDLC, and UART
+
+T1023 Personality
+------------------
+T1023 is a reduced personality of T1024 without QUICC Engine, DIU, and
+unavailable deep sleep. Rest of the blocks are almost same as T1024.
+Differences between T1024 and T1023
+Feature		T1024  T1023
+QUICC Engine:	yes    no
+DIU:		yes    no
+Deep Sleep:	yes    no
+I2C controller: 4      3
+DDR:		64-bit 32-bit
+IFC:		32-bit 28-bit
+
+
+T1024QDS board Overview
+-----------------------
+- SERDES Connections
+  4 lanes supporting the following:
+  - PCI Express: supports Gen 1 and Gen 2
+  - SGMII 1G and SGMII 2.5G
+  - QSGMII
+  - XFI
+  - SATA 2.0
+  - High-speed multiplexers route the SerDes traffic to appropriate slots or connectors.
+  - Aurora debug with dedicated connectors.
+- DDR Controller
+  - Supports up to 1600 MTPS data-rate.
+  - Supports one DDR4 or DDR3L module using DDR4 to DDR3L adapter card.
+    - Supports Single-, dual- or quad-rank DIMMs
+  - DDR power supplies 1.35V (DDR3L)/1.20V (DDR4) to all devices with automatic tracking of VTT.
+- IFC/Local Bus
+  - NAND Flash: 8-bit, async, up to 2GB
+  - NOR: 8-bit or 16-bit, non-multiplexed, up to 512MB
+    - NOR devices support 8 virtual banks
+    - Socketed to allow alternate devices
+  - GASIC: Simple (minimal) target within QIXIS FPGA
+  - PromJET rapid memory download support
+  - IFC Debug/Development card
+- Ethernet
+  - Two on-board RGMII 10M/100M/1G ethernet ports.
+  - One QSGMII interface
+  - Four SGMII interface supporting 1Gbps
+  - Three SGMII interfaces supporting 2.5Gbps
+  - one 10Gbps XFI or 10Base-KR interface
+- QIXIS System Logic FPGA
+  - Manages system power and reset sequencing.
+  - Manages the configurations of DUT, board, and clock for dynamic shmoo.
+  - Collects V-I-T data in background for code/power profiling.
+  - Supports legacy TMT test features (POSt, IRS, SYSCLK-synchronous assertion).
+  - General fault monitoring and logging.
+  - Powered from ATX 'standby' power supply that allows continuous operation while rest of the system is off.
+- Clocks
+  - System and DDR clock (SYSCLK, DDRCLK).
+    - Switch selectable to one of 16 common settings in the interval of 64 MHz-166 MHz.
+    - Software programmable in 1 MHz increments from 1-200 MHz.
+  - SERDES clocks
+    - Provides clocks to SerDes blocks and slots.
+    - 100 MHz, 125 MHz and 156.25 MHz options.
+    - Spread-spectrum option for 100 MHz.
+- Power Supplies
+  - Dedicated PMBus regulator for VDD and VDDC.
+  - Adjustable from 0.7V to 1.3V at 35A
+    - VDD can be disabled independanty from VDDC for “deep sleep”.
+    - DDR3L/DDR4 power supply for GVDD: 1.35 or 1.20V at up to 22A.
+    - VTT/MVREF automatically track operating voltage.
+    - Dedicated 2.5V VPP supply.
+  - Dedicated regulators/filters for AVDD supplies.
+  - Dedicated regulators for other supplies, for example OVDD, CVDD, DVDD, LVDD, POVDD, and EVDD.
+- Video
+  - DIU supports video up to 1280x1024x32 bpp.
+    - Chrontel CH7201 for HDMI connection.
+    - TI DS90C387R for direct LCD connection.
+    - Raw (not encoded) video connector for testing or other encoders.
+- USB
+  - Supports two USB 2.0 ports with integrated PHYs.
+    - Two type A ports with 5V@1.5A per port.
+    - Second port can be converted to OTG mini-AB.
+- SDHC
+  For T1024QDS, the SDHC port connects directly to an adapter card slot that has the following features:
+    - upport for optional clock feedback paths.
+    - Support for optional high-speed voltage translation direction controls.
+    - Support for SD slots for: SD, SDHC (1x, 4x, 8x) and MMC.
+    - Support for eMMC memory devices.
+- SPI
+  -On-board support of 3 different devices and sizes.
+- Other IO
+  - Two Serial ports
+  - ProfiBus port
+  - Four I2C ports
+
+
+Memory map on T1024QDS
+----------------------
+Start Address  End Address      Description			Size
+0xF_FFDF_0000  0xF_FFDF_0FFF    IFC - FPGA			4KB
+0xF_FF80_0000  0xF_FF80_FFFF    IFC - NAND Flash		64KB
+0xF_FE00_0000  0xF_FEFF_FFFF    CCSRBAR				16MB
+0xF_F802_0000  0xF_F802_FFFF    PCI Express 3 I/O Space		64KB
+0xF_F801_0000  0xF_F801_FFFF    PCI Express 2 I/O Space		64KB
+0xF_F800_0000  0xF_F800_FFFF    PCI Express 1 I/O Space		64KB
+0xF_F600_0000  0xF_F7FF_FFFF    Queue manager software portal   32MB
+0xF_F400_0000  0xF_F5FF_FFFF    Buffer manager software portal  32MB
+0xF_E800_0000  0xF_EFFF_FFFF    IFC - NOR Flash			128MB
+0xF_E000_0000  0xF_E7FF_FFFF    Promjet				128MB
+0xF_0000_0000  0xF_003F_FFFF    DCSR				4MB
+0xC_2000_0000  0xC_2FFF_FFFF    PCI Express 3 Mem Space		256MB
+0xC_1000_0000  0xC_1FFF_FFFF    PCI Express 2 Mem Space		256MB
+0xC_0000_0000  0xC_0FFF_FFFF    PCI Express 1 Mem Space		256MB
+0x0_0000_0000  0x0_ffff_ffff    DDR				4GB
+
+
+128MB NOR Flash memory Map
+--------------------------
+Start Address   End Address     Definition			Max size
+0xEFF40000      0xEFFFFFFF      u-boot (current bank)		768KB
+0xEFF20000      0xEFF3FFFF      u-boot env (current bank)	128KB
+0xEFF00000      0xEFF1FFFF      FMAN Ucode (current bank)	128KB
+0xEFE00000      0xEFE3FFFF      QE firmware (current bank)	256KB
+0xED300000      0xEFEFFFFF      rootfs (alt bank)		44MB
+0xEC800000      0xEC8FFFFF      Hardware device tree (alt bank) 1MB
+0xEC020000      0xEC7FFFFF      Linux.uImage (alt bank)		7MB + 875KB
+0xEC000000      0xEC01FFFF      RCW (alt bank)			128KB
+0xEBF40000      0xEBFFFFFF      u-boot (alt bank)		768KB
+0xEBF20000      0xEBF3FFFF      u-boot env (alt bank)		128KB
+0xEBF00000      0xEBF1FFFF      FMAN ucode (alt bank)		128KB
+0xEBE00000      0xEBE3FFFF      QE firmware (alt bank)		256KB
+0xE9300000      0xEBEFFFFF      rootfs (current bank)		44MB
+0xE8800000      0xE88FFFFF      Hardware device tree (cur bank) 1MB
+0xE8020000      0xE86FFFFF      Linux.uImage (current bank)	7MB + 875KB
+0xE8000000      0xE801FFFF      RCW (current bank)		128KB
+
+
+SerDes clock vs DIP-switch settings
+-----------------------------------
+SRDS_PRTCL_S1	SD1_REF_CLK1	SD1_REF_CLK2	SW4[1:4]
+0x6F		100MHz		125MHz		1101
+0xD6		100MHz		100MHz		1111
+0x99		156.25MHz	100MHz		1011
+
+
+T1024 Clock frequency
+----------------------
+BIN   Core     DDR       Platform  FMan
+Bin1: 1400MHz  1600MT/s  400MHz    700MHz
+Bin2: 1200MHz  1600MT/s  400MHz    600MHz
+Bin3: 1000MHz  1600MT/s  400MHz    500MHz
+
+
+
+Software configurations and board settings
+------------------------------------------
+1. NOR boot:
+   a. build NOR boot image
+	$  make T1024QDS_defconfig    (For DDR3L, by default)
+	or make T1024QDS_D4_defconfig (For DDR4)
+	$  make
+   b. program u-boot.bin image to NOR flash
+	=> tftp 1000000 u-boot.bin
+	=> pro off all;era eff40000 efffffff;cp.b 1000000 eff40000 $filesize
+	set SW1[1:8] = '00010011', SW2[1] = '1', SW6[1:4] = '0000' for NOR boot
+
+   Switching between default bank0 and alternate bank4 on NOR flash
+   To change boot source to vbank4:
+	via software:   run command 'qixis_reset altbank' in u-boot.
+	via DIP-switch: set SW6[1:4] = '0100'
+
+   To change boot source to vbank0:
+	via software:   run command 'qixis_reset' in u-boot.
+	via DIP-Switch: set SW6[1:4] = '0000'
+
+2. NAND Boot:
+   a. build PBL image for NAND boot
+	$ make T1024QDS_NAND_defconfig
+	$ make
+   b. program u-boot-with-spl-pbl.bin to NAND flash
+	=> tftp 1000000 u-boot-with-spl-pbl.bin
+	=> nand erase 0 $filesize
+	=> nand write 1000000 0 $filesize
+	set SW1[1:8] = '10000010', SW2[1] = '0' and SW6[1:4] = '1001' for NAND boot
+
+3. SPI Boot:
+   a. build PBL image for SPI boot
+	$ make T1024QDS_SPIFLASH_defconfig
+	$ make
+   b. program u-boot-with-spl-pbl.bin to SPI flash
+	=> tftp 1000000 u-boot-with-spl-pbl.bin
+	=> sf probe 0
+	=> sf erase 0 f0000
+	=> sf write 1000000 0 $filesize
+	set SW1[1:8] = '00100010', SW2[1] ='1' for SPI boot
+
+4. SD Boot:
+   a. build PBL image for SD boot
+	$ make T1024QDS_SDCARD_defconfig
+	$ make
+   b. program u-boot-with-spl-pbl.bin to SD/MMC card
+	=> tftp 1000000 u-boot-with-spl-pbl.bin
+	=> mmc write 1000000 8 0x800
+	=> tftp 1000000 fsl_fman_ucode_t1024_xx.bin
+	=> mmc write 1000000 0x820 80
+	set SW1[1:8] = '00100000', SW2[1] = '0' for SD boot
+
+
+DIU/QE-TDM/SDXC settings
+-------------------
+a) For TDM Riser:     set pin_mux=tdm in hwconfig
+b) For UCC(ProfiBus): set pin_mux=ucc in hwconfig
+c) For HDMI(DVI):     set pin_mux=hdmi in hwconfig
+d) For LCD(DFP):      set pin_mux=lcd in hwconfig
+e) For SDXC:	      set adaptor=sdxc in hwconfig
+
+2-stage NAND/SPI/SD boot loader
+-------------------------------
+PBL initializes the internal CPC-SRAM and copy SPL(160K) to SRAM.
+SPL further initializes DDR using SPD and environment variables
+and copy u-boot(768 KB) from NAND/SPI/SD device to DDR.
+Finally SPL transers control to u-boot for futher booting.
+
+SPL has following features:
+ - Executes within 256K
+ - No relocation required
+
+Run time view of SPL framework
+-------------------------------------------------
+|Area		   | Address			|
+-------------------------------------------------
+|SecureBoot header | 0xFFFC0000 (32KB)		|
+-------------------------------------------------
+|GD, BD		   | 0xFFFC8000 (4KB)		|
+-------------------------------------------------
+|ENV		   | 0xFFFC9000 (8KB)		|
+-------------------------------------------------
+|HEAP		   | 0xFFFCB000 (30KB)		|
+-------------------------------------------------
+|STACK		   | 0xFFFD8000 (22KB)		|
+-------------------------------------------------
+|U-boot SPL	   | 0xFFFD8000 (160KB)		|
+-------------------------------------------------
+
+NAND Flash memory Map on T1024QDS
+-------------------------------------------------------------
+Start		End		Definition	Size
+0x000000	0x0FFFFF	u-boot		1MB
+0x100000	0x15FFFF	u-boot env	8KB
+0x160000	0x17FFFF	FMAN Ucode	128KB
+0x180000	0x19FFFF	QE Firmware	128KB
+
+
+SD Card memory Map on T1024QDS
+----------------------------------------------------
+Block		#blocks		Definition	Size
+0x008		2048		u-boot img	1MB
+0x800		0016		u-boot env	8KB
+0x820		0256		FMAN Ucode	128KB
+0x920		0256		QE Firmware	128KB
+
+
+SPI Flash memory Map on T1024QDS
+----------------------------------------------------
+Start		End		Definition	Size
+0x000000	0x0FFFFF	u-boot img	1MB
+0x100000	0x101FFF	u-boot env	8KB
+0x110000	0x12FFFF	FMAN Ucode	128KB
+0x130000	0x14FFFF	QE Firmware	128KB
+
+
+For more details, please refer to T1024QDS Reference Manual and access
+website www.freescale.com and Freescale QorIQ SDK Infocenter document.
diff --git a/board/freescale/t102xqds/ddr.c b/board/freescale/t102xqds/ddr.c
new file mode 100644
index 0000000..46fc64e
--- /dev/null
+++ b/board/freescale/t102xqds/ddr.c
@@ -0,0 +1,170 @@
+/*
+ * Copyright 2014 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <i2c.h>
+#include <hwconfig.h>
+#include <asm/mmu.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
+#include <asm/fsl_law.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+struct board_specific_parameters {
+	u32 n_ranks;
+	u32 datarate_mhz_high;
+	u32 rank_gb;
+	u32 clk_adjust;
+	u32 wrlvl_start;
+	u32 wrlvl_ctl_2;
+	u32 wrlvl_ctl_3;
+};
+
+/*
+ * datarate_mhz_high values need to be in ascending order
+ */
+static const struct board_specific_parameters udimm0[] = {
+	/*
+	 * memory controller 0
+	 *   num|  hi| rank|  clk| wrlvl |   wrlvl   |  wrlvl |
+	 * ranks| mhz| GB  |adjst| start |   ctl2    |  ctl3  |
+	 */
+#if defined(CONFIG_SYS_FSL_DDR4)
+	{2,  1666,  0,  4,  7,  0x0808090B,  0x0C0D0E0A,},
+	{2,  1900,  0,  4,  6,  0x08080A0C,  0x0D0E0F0A,},
+	{1,  1666,  0,  4,  6,  0x0708090B,  0x0C0D0E09,},
+	{1,  1900,  0,  4,  6,  0x08080A0C,  0x0D0E0F0A,},
+	{1,  2200,  0,  4,  7,  0x08090A0D,  0x0F0F100C,},
+#elif defined(CONFIG_SYS_FSL_DDR3)
+	{2,  833,   0,  4,  6,  0x06060607,  0x08080807,},
+	{2,  1350,  0,  4,  7,  0x0708080A,  0x0A0B0C09,},
+	{2,  1666,  0,  4,  7,  0x0808090B,  0x0C0D0E0A,},
+	{1,  833,   0,  4,  6,  0x06060607,  0x08080807,},
+	{1,  1350,  0,  4,  7,  0x0708080A,  0x0A0B0C09,},
+	{1,  1666,  0,  4,  7,  0x0808090B,  0x0C0D0E0A,},
+#else
+#error DDR type not defined
+#endif
+	{}
+};
+
+static const struct board_specific_parameters *udimms[] = {
+	udimm0,
+};
+
+void fsl_ddr_board_options(memctl_options_t *popts,
+			   dimm_params_t *pdimm,
+			   unsigned int ctrl_num)
+{
+	const struct board_specific_parameters *pbsp, *pbsp_highest = NULL;
+	ulong ddr_freq;
+	struct cpu_type *cpu = gd->arch.cpu;
+
+	if (ctrl_num > 2) {
+		printf("Not supported controller number %d\n", ctrl_num);
+		return;
+	}
+	if (!pdimm->n_ranks)
+		return;
+
+	pbsp = udimms[0];
+
+	/* Get clk_adjust according to the board ddr freqency and n_banks
+	 * specified in board_specific_parameters table.
+	 */
+	ddr_freq = get_ddr_freq(0) / 1000000;
+	while (pbsp->datarate_mhz_high) {
+		if (pbsp->n_ranks == pdimm->n_ranks &&
+		    (pdimm->rank_density >> 30) >= pbsp->rank_gb) {
+			if (ddr_freq <= pbsp->datarate_mhz_high) {
+				popts->clk_adjust = pbsp->clk_adjust;
+				popts->wrlvl_start = pbsp->wrlvl_start;
+				popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
+				popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
+				goto found;
+			}
+			pbsp_highest = pbsp;
+		}
+		pbsp++;
+	}
+
+	if (pbsp_highest) {
+		printf("Error: board specific timing not found\n");
+		printf("for data rate %lu MT/s\n", ddr_freq);
+		printf("Trying to use the highest speed (%u) parameters\n",
+		       pbsp_highest->datarate_mhz_high);
+		popts->clk_adjust = pbsp_highest->clk_adjust;
+		popts->wrlvl_start = pbsp_highest->wrlvl_start;
+		popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
+		popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
+	} else {
+		panic("DIMM is not supported by this board");
+	}
+found:
+	debug("Found timing match: n_ranks %d, data rate %d, rank_gb %d\n",
+	      pbsp->n_ranks, pbsp->datarate_mhz_high, pbsp->rank_gb);
+	debug("\tclk_adjust %d, wrlvl_start %d, wrlvl_ctrl_2 0x%x, ",
+	      pbsp->clk_adjust, pbsp->wrlvl_start, pbsp->wrlvl_ctl_2);
+	debug("wrlvl_ctrl_3 0x%x\n", pbsp->wrlvl_ctl_3);
+
+	/*
+	 * Factors to consider for half-strength driver enable:
+	 *	- number of DIMMs installed
+	 */
+	popts->half_strength_driver_enable = 1;
+	/*
+	 * Write leveling override
+	 */
+	popts->wrlvl_override = 1;
+	popts->wrlvl_sample = 0xf;
+
+	/*
+	 * rtt and rtt_wr override
+	 */
+	popts->rtt_override = 0;
+
+	/* Enable ZQ calibration */
+	popts->zq_en = 1;
+
+	/* DHC_EN =1, ODT = 75 Ohm */
+#ifdef CONFIG_SYS_FSL_DDR4
+	popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_80ohm);
+	popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_80ohm) |
+			  DDR_CDR2_VREF_OVRD(70);	/* Vref = 70% */
+#else
+	popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_75ohm);
+	popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_75ohm);
+#endif
+
+	/* T1023 supports max DDR bus 32bit width, T1024 supports DDR 64bit,
+	 * set DDR bus width to 32bit for T1023
+	 */
+	if (cpu->soc_ver == SVR_T1023)
+		popts->data_bus_width = DDR_DATA_BUS_WIDTH_32;
+
+#ifdef CONFIG_FORCE_DDR_DATA_BUS_WIDTH_32
+	/* for DDR bus 32bit test on T1024 */
+	popts->data_bus_width = DDR_DATA_BUS_WIDTH_32;
+#endif
+}
+
+phys_size_t initdram(int board_type)
+{
+	phys_size_t dram_size;
+
+#if defined(CONFIG_SPL_BUILD) || !defined(CONFIG_RAMBOOT_PBL)
+	puts("Initializing....using SPD\n");
+
+	dram_size = fsl_ddr_sdram();
+	dram_size = setup_ddr_tlbs(dram_size / 0x100000);
+	dram_size *= 0x100000;
+#else
+	/* DDR has been initialised by first stage boot loader */
+	dram_size =  fsl_ddr_sdram_size();
+#endif
+	return dram_size;
+}
diff --git a/board/freescale/t102xqds/eth_t102xqds.c b/board/freescale/t102xqds/eth_t102xqds.c
new file mode 100644
index 0000000..7723f58
--- /dev/null
+++ b/board/freescale/t102xqds/eth_t102xqds.c
@@ -0,0 +1,442 @@
+/*
+ * Copyright 2014 Freescale Semiconductor, Inc.
+ *
+ * Shengzhou Liu <Shengzhou.Liu@freescale.com>
+ *
+ * SPDX-License-Identifier:     GPL-2.0+
+ */
+
+#include <common.h>
+#include <command.h>
+#include <netdev.h>
+#include <asm/mmu.h>
+#include <asm/processor.h>
+#include <asm/immap_85xx.h>
+#include <asm/fsl_law.h>
+#include <asm/fsl_serdes.h>
+#include <asm/fsl_portals.h>
+#include <asm/fsl_liodn.h>
+#include <malloc.h>
+#include <fm_eth.h>
+#include <fsl_mdio.h>
+#include <miiphy.h>
+#include <phy.h>
+#include <asm/fsl_dtsec.h>
+#include <asm/fsl_serdes.h>
+#include "../common/qixis.h"
+#include "../common/fman.h"
+#include "t102xqds_qixis.h"
+
+#define EMI_NONE	0xFFFFFFFF
+#define EMI1_RGMII1	0
+#define EMI1_RGMII2	1
+#define EMI1_SLOT1	2
+#define EMI1_SLOT2	3
+#define EMI1_SLOT3	4
+#define EMI1_SLOT4	5
+#define EMI1_SLOT5	6
+#define EMI2		7
+
+static int mdio_mux[NUM_FM_PORTS];
+
+static const char * const mdio_names[] = {
+	"T1024QDS_MDIO_RGMII1",
+	"T1024QDS_MDIO_RGMII2",
+	"T1024QDS_MDIO_SLOT1",
+	"T1024QDS_MDIO_SLOT2",
+	"T1024QDS_MDIO_SLOT3",
+	"T1024QDS_MDIO_SLOT4",
+	"T1024QDS_MDIO_SLOT5",
+	"T1024QDS_MDIO_10GC",
+	"NULL",
+};
+
+/* Map SerDes1 4 lanes to default slot, will be initialized dynamically */
+static u8 lane_to_slot[] = {2, 3, 4, 5};
+
+static const char *t1024qds_mdio_name_for_muxval(u8 muxval)
+{
+	return mdio_names[muxval];
+}
+
+struct mii_dev *mii_dev_for_muxval(u8 muxval)
+{
+	struct mii_dev *bus;
+	const char *name;
+
+	if (muxval > EMI2)
+		return NULL;
+
+	name = t1024qds_mdio_name_for_muxval(muxval);
+
+	if (!name) {
+		printf("No bus for muxval %x\n", muxval);
+		return NULL;
+	}
+
+	bus = miiphy_get_dev_by_name(name);
+
+	if (!bus) {
+		printf("No bus by name %s\n", name);
+		return NULL;
+	}
+
+	return bus;
+}
+
+struct t1024qds_mdio {
+	u8 muxval;
+	struct mii_dev *realbus;
+};
+
+static void t1024qds_mux_mdio(u8 muxval)
+{
+	u8 brdcfg4;
+
+	if (muxval < 7) {
+		brdcfg4 = QIXIS_READ(brdcfg[4]);
+		brdcfg4 &= ~BRDCFG4_EMISEL_MASK;
+		brdcfg4 |= (muxval << BRDCFG4_EMISEL_SHIFT);
+		QIXIS_WRITE(brdcfg[4], brdcfg4);
+	}
+}
+
+static int t1024qds_mdio_read(struct mii_dev *bus, int addr, int devad,
+			      int regnum)
+{
+	struct t1024qds_mdio *priv = bus->priv;
+
+	t1024qds_mux_mdio(priv->muxval);
+
+	return priv->realbus->read(priv->realbus, addr, devad, regnum);
+}
+
+static int t1024qds_mdio_write(struct mii_dev *bus, int addr, int devad,
+			       int regnum, u16 value)
+{
+	struct t1024qds_mdio *priv = bus->priv;
+
+	t1024qds_mux_mdio(priv->muxval);
+
+	return priv->realbus->write(priv->realbus, addr, devad, regnum, value);
+}
+
+static int t1024qds_mdio_reset(struct mii_dev *bus)
+{
+	struct t1024qds_mdio *priv = bus->priv;
+
+	return priv->realbus->reset(priv->realbus);
+}
+
+static int t1024qds_mdio_init(char *realbusname, u8 muxval)
+{
+	struct t1024qds_mdio *pmdio;
+	struct mii_dev *bus = mdio_alloc();
+
+	if (!bus) {
+		printf("Failed to allocate t1024qds MDIO bus\n");
+		return -1;
+	}
+
+	pmdio = malloc(sizeof(*pmdio));
+	if (!pmdio) {
+		printf("Failed to allocate t1024qds private data\n");
+		free(bus);
+		return -1;
+	}
+
+	bus->read = t1024qds_mdio_read;
+	bus->write = t1024qds_mdio_write;
+	bus->reset = t1024qds_mdio_reset;
+	sprintf(bus->name, t1024qds_mdio_name_for_muxval(muxval));
+
+	pmdio->realbus = miiphy_get_dev_by_name(realbusname);
+
+	if (!pmdio->realbus) {
+		printf("No bus with name %s\n", realbusname);
+		free(bus);
+		free(pmdio);
+		return -1;
+	}
+
+	pmdio->muxval = muxval;
+	bus->priv = pmdio;
+	return mdio_register(bus);
+}
+
+void board_ft_fman_fixup_port(void *fdt, char *compat, phys_addr_t addr,
+			      enum fm_port port, int offset)
+{
+	struct fixed_link f_link;
+
+	if (fm_info_get_enet_if(port) == PHY_INTERFACE_MODE_RGMII) {
+		if (port == FM1_DTSEC3) {
+			fdt_set_phy_handle(fdt, compat, addr, "rgmii_phy2");
+			fdt_setprop(fdt, offset, "phy-connection-type",
+				    "rgmii", 5);
+			fdt_status_okay_by_alias(fdt, "emi1_rgmii1");
+		}
+	} else if (fm_info_get_enet_if(port) == PHY_INTERFACE_MODE_SGMII) {
+		if (port == FM1_DTSEC1) {
+			fdt_set_phy_handle(fdt, compat, addr,
+					   "sgmii_vsc8234_phy_s5");
+		} else if (port == FM1_DTSEC2) {
+			fdt_set_phy_handle(fdt, compat, addr,
+					   "sgmii_vsc8234_phy_s4");
+		}
+	} else if (fm_info_get_enet_if(port) == PHY_INTERFACE_MODE_SGMII_2500) {
+		if (port == FM1_DTSEC3) {
+			fdt_set_phy_handle(fdt, compat, addr,
+					   "sgmii_aqr105_phy_s3");
+		}
+	} else if (fm_info_get_enet_if(port) == PHY_INTERFACE_MODE_QSGMII) {
+		switch (port) {
+		case FM1_DTSEC1:
+			fdt_set_phy_handle(fdt, compat, addr, "qsgmii_phy_p1");
+			break;
+		case FM1_DTSEC2:
+			fdt_set_phy_handle(fdt, compat, addr, "qsgmii_phy_p2");
+			break;
+		case FM1_DTSEC3:
+			fdt_set_phy_handle(fdt, compat, addr, "qsgmii_phy_p3");
+			break;
+		case FM1_DTSEC4:
+			fdt_set_phy_handle(fdt, compat, addr, "qsgmii_phy_p4");
+			break;
+		default:
+			break;
+		}
+		fdt_delprop(fdt, offset, "phy-connection-type");
+		fdt_setprop(fdt, offset, "phy-connection-type", "qsgmii", 6);
+		fdt_status_okay_by_alias(fdt, "emi1_slot2");
+	} else if (fm_info_get_enet_if(port) == PHY_INTERFACE_MODE_XGMII) {
+		/* XFI interface */
+		f_link.phy_id = port;
+		f_link.duplex = 1;
+		f_link.link_speed = 10000;
+		f_link.pause = 0;
+		f_link.asym_pause = 0;
+		/* no PHY for XFI */
+		fdt_delprop(fdt, offset, "phy-handle");
+		fdt_setprop(fdt, offset, "fixed-link", &f_link, sizeof(f_link));
+		fdt_setprop(fdt, offset, "phy-connection-type", "xgmii", 5);
+	}
+}
+
+void fdt_fixup_board_enet(void *fdt)
+{
+}
+
+/*
+ * This function reads RCW to check if Serdes1{A:D} is configured
+ * to slot 1/2/3/4/5 and update the lane_to_slot[] array accordingly
+ */
+static void initialize_lane_to_slot(void)
+{
+	ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+	u32 srds_s1 = in_be32(&gur->rcwsr[4]) &
+				FSL_CORENET2_RCWSR4_SRDS1_PRTCL;
+
+	srds_s1 >>= FSL_CORENET2_RCWSR4_SRDS1_PRTCL_SHIFT;
+
+	switch (srds_s1) {
+	case 0x46:
+	case 0x47:
+		lane_to_slot[1] = 2;
+		break;
+	default:
+		break;
+	}
+}
+
+int board_eth_init(bd_t *bis)
+{
+#if defined(CONFIG_FMAN_ENET)
+	int i, idx, lane, slot, interface;
+	struct memac_mdio_info dtsec_mdio_info;
+	struct memac_mdio_info tgec_mdio_info;
+	ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+	u32 srds_s1;
+
+	srds_s1 = in_be32(&gur->rcwsr[4]) &
+					FSL_CORENET2_RCWSR4_SRDS1_PRTCL;
+	srds_s1 >>= FSL_CORENET2_RCWSR4_SRDS1_PRTCL_SHIFT;
+
+	initialize_lane_to_slot();
+
+	/* Initialize the mdio_mux array so we can recognize empty elements */
+	for (i = 0; i < NUM_FM_PORTS; i++)
+		mdio_mux[i] = EMI_NONE;
+
+	dtsec_mdio_info.regs =
+		(struct memac_mdio_controller *)CONFIG_SYS_FM1_DTSEC_MDIO_ADDR;
+
+	dtsec_mdio_info.name = DEFAULT_FM_MDIO_NAME;
+
+	/* Register the 1G MDIO bus */
+	fm_memac_mdio_init(bis, &dtsec_mdio_info);
+
+	tgec_mdio_info.regs =
+		(struct memac_mdio_controller *)CONFIG_SYS_FM1_TGEC_MDIO_ADDR;
+	tgec_mdio_info.name = DEFAULT_FM_TGEC_MDIO_NAME;
+
+	/* Register the 10G MDIO bus */
+	fm_memac_mdio_init(bis, &tgec_mdio_info);
+
+	/* Register the muxing front-ends to the MDIO buses */
+	t1024qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_RGMII1);
+	t1024qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_RGMII2);
+	t1024qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_SLOT1);
+	t1024qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_SLOT2);
+	t1024qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_SLOT3);
+	t1024qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_SLOT4);
+	t1024qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_SLOT5);
+	t1024qds_mdio_init(DEFAULT_FM_TGEC_MDIO_NAME, EMI2);
+
+	/* Set the two on-board RGMII PHY address */
+	fm_info_set_phy_address(FM1_DTSEC3, RGMII_PHY2_ADDR);
+	fm_info_set_phy_address(FM1_DTSEC4, RGMII_PHY1_ADDR);
+
+	switch (srds_s1) {
+	case 0xd5:
+	case 0xd6:
+		/* QSGMII in Slot2 */
+		fm_info_set_phy_address(FM1_DTSEC1, 0x8);
+		fm_info_set_phy_address(FM1_DTSEC2, 0x9);
+		fm_info_set_phy_address(FM1_DTSEC3, 0xa);
+		fm_info_set_phy_address(FM1_DTSEC4, 0xb);
+		break;
+	case 0x95:
+	case 0x99:
+		/*
+		 * XFI does not need a PHY to work, but to avoid U-boot use
+		 * default PHY address which is zero to a MAC when it found
+		 * a MAC has no PHY address, we give a PHY address to XFI
+		 * MAC, and should not use a real XAUI PHY address, since
+		 * MDIO can access it successfully, and then MDIO thinks the
+		 * XAUI card is used for the XFI MAC, which will cause error.
+		 */
+		fm_info_set_phy_address(FM1_10GEC1, 4);
+		fm_info_set_phy_address(FM1_DTSEC2, SGMII_CARD_PORT1_PHY_ADDR);
+		break;
+	case 0x6f:
+		/* SGMII in Slot3, Slot4, Slot5 */
+		fm_info_set_phy_address(FM1_DTSEC1, SGMII_CARD_AQ_PHY_ADDR_S5);
+		fm_info_set_phy_address(FM1_DTSEC2, SGMII_CARD_AQ_PHY_ADDR_S4);
+		fm_info_set_phy_address(FM1_DTSEC3, SGMII_CARD_PORT1_PHY_ADDR);
+		break;
+	case 0x7f:
+		fm_info_set_phy_address(FM1_DTSEC1, SGMII_CARD_AQ_PHY_ADDR_S5);
+		fm_info_set_phy_address(FM1_DTSEC2, SGMII_CARD_AQ_PHY_ADDR_S4);
+		fm_info_set_phy_address(FM1_DTSEC3, SGMII_CARD_AQ_PHY_ADDR_S3);
+		break;
+	case 0x47:
+		fm_info_set_phy_address(FM1_DTSEC1, SGMII_CARD_PORT1_PHY_ADDR);
+		break;
+	case 0x77:
+		fm_info_set_phy_address(FM1_DTSEC1, SGMII_CARD_PORT1_PHY_ADDR);
+		fm_info_set_phy_address(FM1_DTSEC3, SGMII_CARD_AQ_PHY_ADDR_S3);
+		break;
+	case 0x5a:
+		fm_info_set_phy_address(FM1_DTSEC2, SGMII_CARD_PORT1_PHY_ADDR);
+		break;
+	case 0x6a:
+		fm_info_set_phy_address(FM1_DTSEC2, SGMII_CARD_PORT1_PHY_ADDR);
+		fm_info_set_phy_address(FM1_DTSEC3, SGMII_CARD_PORT1_PHY_ADDR);
+		break;
+	case 0x5b:
+		fm_info_set_phy_address(FM1_DTSEC1, SGMII_CARD_PORT1_PHY_ADDR);
+		fm_info_set_phy_address(FM1_DTSEC2, SGMII_CARD_PORT1_PHY_ADDR);
+		break;
+	case 0x6b:
+		fm_info_set_phy_address(FM1_DTSEC1, SGMII_CARD_PORT1_PHY_ADDR);
+		fm_info_set_phy_address(FM1_DTSEC2, SGMII_CARD_PORT1_PHY_ADDR);
+		fm_info_set_phy_address(FM1_DTSEC3, SGMII_CARD_PORT1_PHY_ADDR);
+		break;
+	default:
+		break;
+	}
+
+	for (i = FM1_DTSEC1; i < FM1_DTSEC1 + CONFIG_SYS_NUM_FM1_DTSEC; i++) {
+		idx = i - FM1_DTSEC1;
+		interface = fm_info_get_enet_if(i);
+		switch (interface) {
+		case PHY_INTERFACE_MODE_SGMII:
+		case PHY_INTERFACE_MODE_SGMII_2500:
+		case PHY_INTERFACE_MODE_QSGMII:
+			if (interface == PHY_INTERFACE_MODE_SGMII) {
+				lane = serdes_get_first_lane(FSL_SRDS_1,
+						SGMII_FM1_DTSEC1 + idx);
+			} else if (interface == PHY_INTERFACE_MODE_SGMII_2500) {
+				lane = serdes_get_first_lane(FSL_SRDS_1,
+						SGMII_2500_FM1_DTSEC1 + idx);
+			} else {
+				lane = serdes_get_first_lane(FSL_SRDS_1,
+						QSGMII_FM1_A);
+			}
+
+			if (lane < 0)
+				break;
+
+			slot = lane_to_slot[lane];
+			debug("FM1@DTSEC%u expects SGMII in slot %u\n",
+			      idx + 1, slot);
+			if (QIXIS_READ(present2) & (1 << (slot - 1)))
+				fm_disable_port(i);
+
+			switch (slot) {
+			case 2:
+				mdio_mux[i] = EMI1_SLOT2;
+				fm_info_set_mdio(i, mii_dev_for_muxval(
+						 mdio_mux[i]));
+				break;
+			case 3:
+				mdio_mux[i] = EMI1_SLOT3;
+				fm_info_set_mdio(i, mii_dev_for_muxval(
+						 mdio_mux[i]));
+				break;
+			case 4:
+				mdio_mux[i] = EMI1_SLOT4;
+				fm_info_set_mdio(i, mii_dev_for_muxval(
+						 mdio_mux[i]));
+				break;
+			case 5:
+				mdio_mux[i] = EMI1_SLOT5;
+				fm_info_set_mdio(i, mii_dev_for_muxval(
+						 mdio_mux[i]));
+				break;
+			}
+			break;
+		case PHY_INTERFACE_MODE_RGMII:
+			if (i == FM1_DTSEC3)
+				mdio_mux[i] = EMI1_RGMII2;
+			else if (i == FM1_DTSEC4)
+				mdio_mux[i] = EMI1_RGMII1;
+			fm_info_set_mdio(i, mii_dev_for_muxval(mdio_mux[i]));
+			break;
+		default:
+			break;
+		}
+	}
+
+	for (i = FM1_10GEC1; i < FM1_10GEC1 + CONFIG_SYS_NUM_FM1_10GEC; i++) {
+		idx = i - FM1_10GEC1;
+		switch (fm_info_get_enet_if(i)) {
+		case PHY_INTERFACE_MODE_XGMII:
+			lane = serdes_get_first_lane(FSL_SRDS_1,
+						     XFI_FM1_MAC1 + idx);
+			if (lane < 0)
+				break;
+			mdio_mux[i] = EMI2;
+			fm_info_set_mdio(i, mii_dev_for_muxval(mdio_mux[i]));
+			break;
+		default:
+			break;
+		}
+	}
+
+	cpu_eth_init(bis);
+#endif /* CONFIG_FMAN_ENET */
+
+	return pci_eth_init(bis);
+}
diff --git a/board/freescale/t102xqds/law.c b/board/freescale/t102xqds/law.c
new file mode 100644
index 0000000..b1c9d01
--- /dev/null
+++ b/board/freescale/t102xqds/law.c
@@ -0,0 +1,32 @@
+/*
+ * Copyright 2014 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/fsl_law.h>
+#include <asm/mmu.h>
+
+struct law_entry law_table[] = {
+#ifndef CONFIG_SYS_NO_FLASH
+	SET_LAW(CONFIG_SYS_FLASH_BASE_PHYS, LAW_SIZE_256M, LAW_TRGT_IF_IFC),
+#endif
+#ifdef CONFIG_SYS_BMAN_MEM_PHYS
+	SET_LAW(CONFIG_SYS_BMAN_MEM_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_BMAN),
+#endif
+#ifdef CONFIG_SYS_QMAN_MEM_PHYS
+	SET_LAW(CONFIG_SYS_QMAN_MEM_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_QMAN),
+#endif
+#ifdef QIXIS_BASE_PHYS
+	SET_LAW(QIXIS_BASE_PHYS, LAW_SIZE_4K, LAW_TRGT_IF_IFC),
+#endif
+#ifdef CONFIG_SYS_DCSRBAR_PHYS
+	SET_LAW(CONFIG_SYS_DCSRBAR_PHYS, LAW_SIZE_4M, LAW_TRGT_IF_DCSR),
+#endif
+#ifdef CONFIG_SYS_NAND_BASE_PHYS
+	SET_LAW(CONFIG_SYS_NAND_BASE_PHYS, LAW_SIZE_64K, LAW_TRGT_IF_IFC),
+#endif
+};
+
+int num_law_entries = ARRAY_SIZE(law_table);
diff --git a/board/freescale/t102xqds/pci.c b/board/freescale/t102xqds/pci.c
new file mode 100644
index 0000000..7369289
--- /dev/null
+++ b/board/freescale/t102xqds/pci.c
@@ -0,0 +1,23 @@
+/*
+ * Copyright 2014 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <command.h>
+#include <pci.h>
+#include <asm/fsl_pci.h>
+#include <libfdt.h>
+#include <fdt_support.h>
+#include <asm/fsl_serdes.h>
+
+void pci_init_board(void)
+{
+	fsl_pcie_init_board(0);
+}
+
+void pci_of_setup(void *blob, bd_t *bd)
+{
+	FT_FSL_PCI_SETUP;
+}
diff --git a/board/freescale/t102xqds/spl.c b/board/freescale/t102xqds/spl.c
new file mode 100644
index 0000000..08aef6e
--- /dev/null
+++ b/board/freescale/t102xqds/spl.c
@@ -0,0 +1,151 @@
+/* Copyright 2014 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:    GPL-2.0+
+ */
+
+#include <common.h>
+#include <malloc.h>
+#include <ns16550.h>
+#include <nand.h>
+#include <i2c.h>
+#include <mmc.h>
+#include <fsl_esdhc.h>
+#include <spi_flash.h>
+#include "../common/qixis.h"
+#include "t102xqds_qixis.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+phys_size_t get_effective_memsize(void)
+{
+	return CONFIG_SYS_L3_SIZE;
+}
+
+unsigned long get_board_sys_clk(void)
+{
+	u8 sysclk_conf = QIXIS_READ(brdcfg[1]);
+
+	switch (sysclk_conf & 0x0F) {
+	case QIXIS_SYSCLK_83:
+		return 83333333;
+	case QIXIS_SYSCLK_100:
+		return 100000000;
+	case QIXIS_SYSCLK_125:
+		return 125000000;
+	case QIXIS_SYSCLK_133:
+		return 133333333;
+	case QIXIS_SYSCLK_150:
+		return 150000000;
+	case QIXIS_SYSCLK_160:
+		return 160000000;
+	case QIXIS_SYSCLK_166:
+		return 166666666;
+	}
+	return 66666666;
+}
+
+unsigned long get_board_ddr_clk(void)
+{
+	u8 ddrclk_conf = QIXIS_READ(brdcfg[1]);
+
+	switch ((ddrclk_conf & 0x30) >> 4) {
+	case QIXIS_DDRCLK_100:
+		return 100000000;
+	case QIXIS_DDRCLK_125:
+		return 125000000;
+	case QIXIS_DDRCLK_133:
+		return 133333333;
+	}
+	return 66666666;
+}
+
+void board_init_f(ulong bootflag)
+{
+	u32 plat_ratio, sys_clk, ccb_clk;
+	ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR;
+
+#if defined(CONFIG_PPC_T1040) && defined(CONFIG_SPL_NAND_BOOT)
+	/*
+	 * There is T1040 SoC issue where NOR, FPGA are inaccessible during
+	 * NAND boot because IFC signals > IFC_AD7 are not enabled.
+	 * This workaround changes RCW source to make all signals enabled.
+	 */
+	u32 porsr1, pinctl;
+#define FSL_CORENET_CCSR_PORSR1_RCW_MASK        0xFF800000
+
+	porsr1 = in_be32(&gur->porsr1);
+	pinctl = ((porsr1 & ~(FSL_CORENET_CCSR_PORSR1_RCW_MASK)) | 0x24800000);
+	out_be32((unsigned int *)(CONFIG_SYS_DCSRBAR + 0x20000), pinctl);
+#endif
+
+	/* Memcpy existing GD at CONFIG_SPL_GD_ADDR */
+	memcpy((void *)CONFIG_SPL_GD_ADDR, (void *)gd, sizeof(gd_t));
+
+	/* Update GD pointer */
+	gd = (gd_t *)(CONFIG_SPL_GD_ADDR);
+
+	console_init_f();
+
+	/* initialize selected port with appropriate baud rate */
+	sys_clk = get_board_sys_clk();
+	plat_ratio = (in_be32(&gur->rcwsr[0]) >> 25) & 0x1f;
+	ccb_clk = sys_clk * plat_ratio / 2;
+
+	NS16550_init((NS16550_t)CONFIG_SYS_NS16550_COM1,
+		     ccb_clk / 16 / CONFIG_BAUDRATE);
+
+#if defined(CONFIG_SPL_MMC_BOOT)
+	puts("\nSD boot...\n");
+#elif defined(CONFIG_SPL_SPI_BOOT)
+	puts("\nSPI boot...\n");
+#elif defined(CONFIG_SPL_NAND_BOOT)
+	puts("\nNAND boot...\n");
+#endif
+
+	relocate_code(CONFIG_SPL_RELOC_STACK, (gd_t *)CONFIG_SPL_GD_ADDR, 0x0);
+}
+
+void board_init_r(gd_t *gd, ulong dest_addr)
+{
+	bd_t *bd;
+
+	bd = (bd_t *)(gd + sizeof(gd_t));
+	memset(bd, 0, sizeof(bd_t));
+	gd->bd = bd;
+	bd->bi_memstart = CONFIG_SYS_INIT_L3_ADDR;
+	bd->bi_memsize = CONFIG_SYS_L3_SIZE;
+
+	probecpu();
+	get_clocks();
+	mem_malloc_init(CONFIG_SPL_RELOC_MALLOC_ADDR,
+			CONFIG_SPL_RELOC_MALLOC_SIZE);
+
+#ifdef CONFIG_SPL_NAND_BOOT
+	nand_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE,
+			    (uchar *)CONFIG_ENV_ADDR);
+#endif
+#ifdef CONFIG_SPL_MMC_BOOT
+	mmc_initialize(bd);
+	mmc_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE,
+			   (uchar *)CONFIG_ENV_ADDR);
+#endif
+#ifdef CONFIG_SPL_SPI_BOOT
+	spi_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE,
+			   (uchar *)CONFIG_ENV_ADDR);
+#endif
+
+	gd->env_addr  = (ulong)(CONFIG_ENV_ADDR);
+	gd->env_valid = 1;
+
+	i2c_init_all();
+
+	gd->ram_size = initdram(0);
+
+#ifdef CONFIG_SPL_MMC_BOOT
+	mmc_boot();
+#elif defined(CONFIG_SPL_SPI_BOOT)
+	spi_boot();
+#elif defined(CONFIG_SPL_NAND_BOOT)
+	nand_boot();
+#endif
+}
diff --git a/board/freescale/t102xqds/t1024_pbi.cfg b/board/freescale/t102xqds/t1024_pbi.cfg
new file mode 100644
index 0000000..7b9e9b0
--- /dev/null
+++ b/board/freescale/t102xqds/t1024_pbi.cfg
@@ -0,0 +1,26 @@
+#PBI commands
+#Initialize CPC1
+09010000 00200400
+09138000 00000000
+091380c0 00000100
+#Configure CPC1 as 256KB SRAM
+09010100 00000000
+09010104 fffc0007
+09010f00 08000000
+09010000 80000000
+#Configure LAW for CPC1
+09000cd0 00000000
+09000cd4 fffc0000
+09000cd8 81000011
+#Configure alternate space
+09000010 00000000
+09000014 ff000000
+09000018 81000000
+#Configure SPI controller
+09110000 80000403
+09110020 2d170008
+09110024 00100008
+09110028 00100008
+0911002c 00100008
+#Flush PBL data
+091380c0 000FFFFF
diff --git a/board/freescale/t102xqds/t1024_rcw.cfg b/board/freescale/t102xqds/t1024_rcw.cfg
new file mode 100644
index 0000000..4b8f719
--- /dev/null
+++ b/board/freescale/t102xqds/t1024_rcw.cfg
@@ -0,0 +1,10 @@
+# single-source clock:Sys_Clock = DDR_Refclock = Diff_Sysclk = 100 MHz
+# Core/DDR/Platform/FMan = 1400MHz/1600MT/s/400MHz/700MHz
+
+# PBL preamble and RCW header for T1024QDS
+aa55aa55 010e0100
+# Serdes protocol 0x6F
+0810000e 00000000 00000000 00000000
+37800001 00000012 e8104000 21000000
+00000000 00000000 00000000 00030810
+00000000 036c5a00 00000000 00000006
diff --git a/board/freescale/t102xqds/t102xqds.c b/board/freescale/t102xqds/t102xqds.c
new file mode 100644
index 0000000..97ef95a
--- /dev/null
+++ b/board/freescale/t102xqds/t102xqds.c
@@ -0,0 +1,321 @@
+/*
+ * Copyright 2014 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <command.h>
+#include <i2c.h>
+#include <netdev.h>
+#include <linux/compiler.h>
+#include <asm/mmu.h>
+#include <asm/processor.h>
+#include <asm/cache.h>
+#include <asm/immap_85xx.h>
+#include <asm/fsl_law.h>
+#include <asm/fsl_serdes.h>
+#include <asm/fsl_portals.h>
+#include <asm/fsl_liodn.h>
+#include <fm_eth.h>
+#include <hwconfig.h>
+#include <asm/mpc85xx_gpio.h>
+#include "../common/qixis.h"
+#include "t102xqds.h"
+#include "t102xqds_qixis.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int checkboard(void)
+{
+	char buf[64];
+	struct cpu_type *cpu = gd->arch.cpu;
+	static const char *const freq[] = {"100", "125", "156.25", "100.0"};
+	int clock;
+	u8 sw = QIXIS_READ(arch);
+
+	printf("Board: %sQDS, ", cpu->name);
+	printf("Sys ID: 0x%02x, Board Arch: V%d, ", QIXIS_READ(id), sw >> 4);
+	printf("Board Version: %c, boot from ", (sw & 0xf) + 'A' - 1);
+
+#ifdef CONFIG_SDCARD
+	puts("SD/MMC\n");
+#elif CONFIG_SPIFLASH
+	puts("SPI\n");
+#else
+	sw = QIXIS_READ(brdcfg[0]);
+	sw = (sw & QIXIS_LBMAP_MASK) >> QIXIS_LBMAP_SHIFT;
+
+	if (sw < 0x8)
+		printf("vBank: %d\n", sw);
+	else if (sw == 0x8)
+		puts("PromJet\n");
+	else if (sw == 0x9)
+		puts("NAND\n");
+	else if (sw == 0x15)
+		printf("IFC Card\n");
+	else
+		printf("invalid setting of SW%u\n", QIXIS_LBMAP_SWITCH);
+#endif
+
+	printf("FPGA: v%d (%s), build %d",
+	       (int)QIXIS_READ(scver), qixis_read_tag(buf),
+	       (int)qixis_read_minor());
+	/* the timestamp string contains "\n" at the end */
+	printf(" on %s", qixis_read_time(buf));
+
+	puts("SERDES Reference: ");
+	sw = QIXIS_READ(brdcfg[2]);
+	clock = (sw >> 6) & 3;
+	printf("Clock1=%sMHz ", freq[clock]);
+	clock = (sw >> 4) & 3;
+	printf("Clock2=%sMHz\n", freq[clock]);
+
+	return 0;
+}
+
+int select_i2c_ch_pca9547(u8 ch)
+{
+	int ret;
+
+	ret = i2c_write(I2C_MUX_PCA_ADDR_PRI, 0, 1, &ch, 1);
+	if (ret) {
+		puts("PCA: failed to select proper channel\n");
+		return ret;
+	}
+
+	return 0;
+}
+
+static int board_mux_lane_to_slot(void)
+{
+	ccsr_gur_t __iomem *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+	u32 srds_prtcl_s1;
+	u8 brdcfg9;
+
+	srds_prtcl_s1 = in_be32(&gur->rcwsr[4]) &
+				FSL_CORENET2_RCWSR4_SRDS1_PRTCL;
+	srds_prtcl_s1 >>= FSL_CORENET2_RCWSR4_SRDS1_PRTCL_SHIFT;
+
+
+	brdcfg9 = QIXIS_READ(brdcfg[9]);
+	QIXIS_WRITE(brdcfg[9], brdcfg9 | BRDCFG9_XFI_TX_DISABLE);
+
+	switch (srds_prtcl_s1) {
+	case 0:
+		/* SerDes1 is not enabled */
+		break;
+	case 0xd5:
+	case 0x5b:
+	case 0x6b:
+	case 0x77:
+	case 0x6f:
+	case 0x7f:
+		QIXIS_WRITE(brdcfg[12], 0x8c);
+		break;
+	case 0x40:
+		QIXIS_WRITE(brdcfg[12], 0xfc);
+		break;
+	case 0xd6:
+	case 0x5a:
+	case 0x6a:
+	case 0x56:
+		QIXIS_WRITE(brdcfg[12], 0x88);
+		break;
+	case 0x47:
+		QIXIS_WRITE(brdcfg[12], 0xcc);
+		break;
+	case 0x46:
+		QIXIS_WRITE(brdcfg[12], 0xc8);
+		break;
+	case 0x95:
+	case 0x99:
+		brdcfg9 &= ~BRDCFG9_XFI_TX_DISABLE;
+		QIXIS_WRITE(brdcfg[9], brdcfg9);
+		QIXIS_WRITE(brdcfg[12], 0x8c);
+		break;
+	case 0x116:
+		QIXIS_WRITE(brdcfg[12], 0x00);
+		break;
+	case 0x115:
+	case 0x119:
+	case 0x129:
+	case 0x12b:
+		/* Aurora, PCIe, SGMII, SATA */
+		QIXIS_WRITE(brdcfg[12], 0x04);
+		break;
+	default:
+		printf("WARNING: unsupported for SerDes Protocol %d\n",
+		       srds_prtcl_s1);
+		return -1;
+	}
+
+	return 0;
+}
+
+#ifdef CONFIG_PPC_T1024
+static void board_mux_setup(void)
+{
+	u8 brdcfg15;
+
+	brdcfg15 = QIXIS_READ(brdcfg[15]);
+	brdcfg15 &= ~BRDCFG15_DIUSEL_MASK;
+
+	if (hwconfig_arg_cmp("pin_mux", "tdm")) {
+		/* Route QE_TDM multiplexed signals to TDM Riser slot */
+		QIXIS_WRITE(brdcfg[15], brdcfg15 | BRDCFG15_DIUSEL_TDM);
+		QIXIS_WRITE(brdcfg[13], BRDCFG13_TDM_INTERFACE << 2);
+	} else if (hwconfig_arg_cmp("pin_mux", "ucc")) {
+		/* to UCC (ProfiBus) interface */
+		QIXIS_WRITE(brdcfg[15], brdcfg15 | BRDCFG15_DIUSEL_UCC);
+	} else if (hwconfig_arg_cmp("pin_mux", "hdmi")) {
+		/* to DVI (HDMI) encoder */
+		QIXIS_WRITE(brdcfg[15], brdcfg15 | BRDCFG15_DIUSEL_HDMI);
+	} else if (hwconfig_arg_cmp("pin_mux", "lcd")) {
+		/* to DFP (LCD) encoder */
+		QIXIS_WRITE(brdcfg[15], brdcfg15 | BRDCFG15_LCDFM |
+			    BRDCFG15_LCDPD | BRDCFG15_DIUSEL_LCD);
+	}
+}
+#endif
+
+int board_early_init_r(void)
+{
+#ifdef CONFIG_SYS_FLASH_BASE
+	const unsigned int flashbase = CONFIG_SYS_FLASH_BASE;
+	int flash_esel = find_tlb_idx((void *)flashbase, 1);
+
+	/*
+	 * Remap Boot flash + PROMJET region to caching-inhibited
+	 * so that flash can be erased properly.
+	 */
+
+	/* Flush d-cache and invalidate i-cache of any FLASH data */
+	flush_dcache();
+	invalidate_icache();
+
+	if (flash_esel == -1) {
+		/* very unlikely unless something is messed up */
+		puts("Error: Could not find TLB for FLASH BASE\n");
+		flash_esel = 2; /* give our best effort to continue */
+	} else {
+		/* invalidate existing TLB entry for flash + promjet */
+		disable_tlb(flash_esel);
+	}
+
+	set_tlb(1, flashbase, CONFIG_SYS_FLASH_BASE_PHYS,
+		MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		0, flash_esel, BOOKE_PAGESZ_256M, 1);
+#endif
+	set_liodns();
+#ifdef CONFIG_SYS_DPAA_QBMAN
+	setup_portals();
+#endif
+	select_i2c_ch_pca9547(I2C_MUX_CH_DEFAULT);
+	board_mux_lane_to_slot();
+	return 0;
+}
+
+unsigned long get_board_sys_clk(void)
+{
+	u8 sysclk_conf = QIXIS_READ(brdcfg[1]);
+
+	switch (sysclk_conf & 0x0F) {
+	case QIXIS_SYSCLK_64:
+		return 64000000;
+	case QIXIS_SYSCLK_83:
+		return 83333333;
+	case QIXIS_SYSCLK_100:
+		return 100000000;
+	case QIXIS_SYSCLK_125:
+		return 125000000;
+	case QIXIS_SYSCLK_133:
+		return 133333333;
+	case QIXIS_SYSCLK_150:
+		return 150000000;
+	case QIXIS_SYSCLK_160:
+		return 160000000;
+	case QIXIS_SYSCLK_166:
+		return 166666666;
+	}
+	return 66666666;
+}
+
+unsigned long get_board_ddr_clk(void)
+{
+	u8 ddrclk_conf = QIXIS_READ(brdcfg[1]);
+
+	switch ((ddrclk_conf & 0x30) >> 4) {
+	case QIXIS_DDRCLK_100:
+		return 100000000;
+	case QIXIS_DDRCLK_125:
+		return 125000000;
+	case QIXIS_DDRCLK_133:
+		return 133333333;
+	}
+	return 66666666;
+}
+
+#define NUM_SRDS_PLL	2
+int misc_init_r(void)
+{
+#ifdef CONFIG_PPC_T1024
+	board_mux_setup();
+#endif
+	return 0;
+}
+
+int ft_board_setup(void *blob, bd_t *bd)
+{
+	phys_addr_t base;
+	phys_size_t size;
+
+	ft_cpu_setup(blob, bd);
+
+	base = getenv_bootm_low();
+	size = getenv_bootm_size();
+
+	fdt_fixup_memory(blob, (u64)base, (u64)size);
+
+#ifdef CONFIG_PCI
+	pci_of_setup(blob, bd);
+#endif
+
+	fdt_fixup_liodn(blob);
+
+#ifdef CONFIG_HAS_FSL_DR_USB
+	fdt_fixup_dr_usb(blob, bd);
+#endif
+
+#ifdef CONFIG_SYS_DPAA_FMAN
+	fdt_fixup_fman_ethernet(blob);
+	fdt_fixup_board_enet(blob);
+#endif
+
+	return 0;
+}
+
+void qixis_dump_switch(void)
+{
+	int i, nr_of_cfgsw;
+
+	QIXIS_WRITE(cms[0], 0x00);
+	nr_of_cfgsw = QIXIS_READ(cms[1]);
+
+	puts("DIP switch settings dump:\n");
+	for (i = 1; i <= nr_of_cfgsw; i++) {
+		QIXIS_WRITE(cms[0], i);
+		printf("SW%d = (0x%02x)\n", i, QIXIS_READ(cms[1]));
+	}
+}
+
+#ifdef CONFIG_DEEP_SLEEP
+void board_mem_sleep_setup(void)
+{
+	/* does not provide HW signals for power management */
+	QIXIS_WRITE(pwr_ctl[1], (QIXIS_READ(pwr_ctl[1]) & ~0x2));
+	/* Disable MCKE isolation */
+	gpio_set_value(2, 0);
+	udelay(1);
+}
+#endif
diff --git a/board/freescale/t102xqds/t102xqds.h b/board/freescale/t102xqds/t102xqds.h
new file mode 100644
index 0000000..64ff623
--- /dev/null
+++ b/board/freescale/t102xqds/t102xqds.h
@@ -0,0 +1,14 @@
+/*
+ * Copyright 2014 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef __T102x_QDS_H__
+#define __T102x_QDS_H__
+
+void fdt_fixup_board_enet(void *blob);
+void pci_of_setup(void *blob, bd_t *bd);
+int select_i2c_ch_pca9547(u8 ch);
+
+#endif
diff --git a/board/freescale/t102xqds/t102xqds_qixis.h b/board/freescale/t102xqds/t102xqds_qixis.h
new file mode 100644
index 0000000..ad83f03
--- /dev/null
+++ b/board/freescale/t102xqds/t102xqds_qixis.h
@@ -0,0 +1,61 @@
+/*
+ * Copyright 2014 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef __T1024QDS_QIXIS_H__
+#define __T1024QDS_QIXIS_H__
+
+/* Definitions of QIXIS Registers for T1024/T1023 QDS */
+
+/* BRDCFG4[4:7]] select EC1 and EC2 as a pair */
+#define BRDCFG4_EMISEL_MASK		0xE0
+#define BRDCFG4_EMISEL_SHIFT		5
+
+/* BRDCFG5[0:1] controls routing and use of I2C3 & I2C4 ports*/
+#define BRDCFG5_IMX_MASK		0xC0
+#define BRDCFG5_IMX_DIU			0x80
+
+#define BRDCFG9_XFI_TX_DISABLE		0x10
+
+/* BRDCFG13[0:5] TDM configuration and setup */
+#define BRDCFG13_TDM_MASK		0xfc
+#define BRDCFG13_TDM_INTERFACE		0x37
+#define BRDCFG13_HDLC_LOOPBACK		0x29
+#define BRDCFG13_TDM_LOOPBACK		0x31
+
+/* BRDCFG15[3] controls LCD Panel Powerdown */
+#define BRDCFG15_LCDFM			0x20
+#define BRDCFG15_LCDPD			0x10
+#define BRDCFG15_LCDPD_MASK		0x10
+#define BRDCFG15_LCDPD_ENABLED		0x00
+
+/* BRDCFG15[6:7] controls DIU MUX selction*/
+#define BRDCFG15_DIUSEL_MASK		0x03
+#define BRDCFG15_DIUSEL_HDMI		0x00
+#define BRDCFG15_DIUSEL_LCD		0x01
+#define BRDCFG15_DIUSEL_UCC		0x10
+#define BRDCFG15_DIUSEL_TDM		0x11
+
+/* SYSCLK */
+#define QIXIS_SYSCLK_66			0x0
+#define QIXIS_SYSCLK_83			0x1
+#define QIXIS_SYSCLK_100		0x2
+#define QIXIS_SYSCLK_125		0x3
+#define QIXIS_SYSCLK_133		0x4
+#define QIXIS_SYSCLK_150		0x5
+#define QIXIS_SYSCLK_160		0x6
+#define QIXIS_SYSCLK_166		0x7
+#define QIXIS_SYSCLK_64			0x8
+
+/* DDRCLK */
+#define QIXIS_DDRCLK_66			0x0
+#define QIXIS_DDRCLK_100		0x1
+#define QIXIS_DDRCLK_125		0x2
+#define QIXIS_DDRCLK_133		0x3
+
+
+#define QIXIS_SRDS1CLK_122		0x5a
+#define QIXIS_SRDS1CLK_125		0x5e
+#endif
diff --git a/board/freescale/t102xqds/tlb.c b/board/freescale/t102xqds/tlb.c
new file mode 100644
index 0000000..409e173
--- /dev/null
+++ b/board/freescale/t102xqds/tlb.c
@@ -0,0 +1,117 @@
+/*
+ * Copyright 2014 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/mmu.h>
+
+struct fsl_e_tlb_entry tlb_table[] = {
+	/* TLB 0 - for temp stack in cache */
+	SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR,
+		      CONFIG_SYS_INIT_RAM_ADDR_PHYS,
+		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
+		      0, 0, BOOKE_PAGESZ_4K, 0),
+	SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024,
+		      CONFIG_SYS_INIT_RAM_ADDR_PHYS + 4 * 1024,
+		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
+		      0, 0, BOOKE_PAGESZ_4K, 0),
+	SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024,
+		      CONFIG_SYS_INIT_RAM_ADDR_PHYS + 8 * 1024,
+		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
+		      0, 0, BOOKE_PAGESZ_4K, 0),
+	SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024,
+		      CONFIG_SYS_INIT_RAM_ADDR_PHYS + 12 * 1024,
+		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
+		      0, 0, BOOKE_PAGESZ_4K, 0),
+
+	/* TLB 1 */
+	/* *I*** - Covers boot page */
+#if defined(CONFIG_SYS_RAMBOOT) && defined(CONFIG_SYS_INIT_L3_ADDR)
+	/*
+	 * *I*G - L3SRAM. When L3 is used as 256K SRAM, the address of the
+	 * SRAM is at 0xfffc0000, it covered the 0xfffff000.
+	 */
+	SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L3_ADDR, CONFIG_SYS_INIT_L3_ADDR,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 0, BOOKE_PAGESZ_256K, 1),
+#else
+	SET_TLB_ENTRY(1, 0xfffff000, 0xfffff000,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 0, BOOKE_PAGESZ_4K, 1),
+#endif
+
+	/* *I*G* - CCSRBAR */
+	SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 1, BOOKE_PAGESZ_16M, 1),
+
+	/* *I*G* - Flash, localbus */
+	/* This will be changed to *I*G* after relocation to RAM. */
+	SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE_PHYS,
+		      MAS3_SX|MAS3_SR, MAS2_W|MAS2_G,
+		      0, 2, BOOKE_PAGESZ_256M, 1),
+
+#ifndef CONFIG_SPL_BUILD
+	/* *I*G* - PCI */
+	SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT, CONFIG_SYS_PCIE1_MEM_PHYS,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 3, BOOKE_PAGESZ_1G, 1),
+
+	/* *I*G* - PCI I/O */
+	SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_IO_VIRT, CONFIG_SYS_PCIE1_IO_PHYS,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 4, BOOKE_PAGESZ_256K, 1),
+
+	/* Bman/Qman */
+#ifdef CONFIG_SYS_BMAN_MEM_PHYS
+	SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE, CONFIG_SYS_BMAN_MEM_PHYS,
+		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
+		      0, 5, BOOKE_PAGESZ_16M, 1),
+	SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE + 0x01000000,
+		      CONFIG_SYS_BMAN_MEM_PHYS + 0x01000000,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 6, BOOKE_PAGESZ_16M, 1),
+#endif
+#ifdef CONFIG_SYS_QMAN_MEM_PHYS
+	SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE, CONFIG_SYS_QMAN_MEM_PHYS,
+		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
+		      0, 7, BOOKE_PAGESZ_16M, 1),
+	SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE + 0x01000000,
+		      CONFIG_SYS_QMAN_MEM_PHYS + 0x01000000,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 8, BOOKE_PAGESZ_16M, 1),
+#endif
+#endif
+#ifdef CONFIG_SYS_DCSRBAR_PHYS
+	SET_TLB_ENTRY(1, CONFIG_SYS_DCSRBAR, CONFIG_SYS_DCSRBAR_PHYS,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 9, BOOKE_PAGESZ_4M, 1),
+#endif
+#ifdef CONFIG_SYS_NAND_BASE
+	SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE_PHYS,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 10, BOOKE_PAGESZ_64K, 1),
+#endif
+#ifdef QIXIS_BASE
+	SET_TLB_ENTRY(1, QIXIS_BASE, QIXIS_BASE_PHYS,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 11, BOOKE_PAGESZ_4K, 1),
+#endif
+
+#if defined(CONFIG_RAMBOOT_PBL) && !defined(CONFIG_SPL_BUILD)
+	SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE, CONFIG_SYS_DDR_SDRAM_BASE,
+		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
+		      0, 12, BOOKE_PAGESZ_1G, 1),
+	SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE + 0x40000000,
+		      CONFIG_SYS_DDR_SDRAM_BASE + 0x40000000,
+		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
+		      0, 13, BOOKE_PAGESZ_1G, 1)
+#endif
+	/* entry 14 and 15 has been used hard coded, they will be disabled
+	 * in cpu_init_f, so if needed more, will use entry 16 later.
+	 */
+};
+
+int num_tlb_entries = ARRAY_SIZE(tlb_table);