exynos: Enable the LCD backlight for snow
The backlight uses FETs on the TPS65090. Enable this so that the display
is visible.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
diff --git a/board/samsung/smdk5250/exynos5-dt.c b/board/samsung/smdk5250/exynos5-dt.c
index bce7583..d6ce133 100644
--- a/board/samsung/smdk5250/exynos5-dt.c
+++ b/board/samsung/smdk5250/exynos5-dt.c
@@ -11,9 +11,9 @@
#include <i2c.h>
#include <netdev.h>
#include <spi.h>
+#include <asm/gpio.h>
#include <asm/arch/cpu.h>
#include <asm/arch/dwmmc.h>
-#include <asm/arch/gpio.h>
#include <asm/arch/mmc.h>
#include <asm/arch/pinmux.h>
#include <asm/arch/power.h>
@@ -180,6 +180,59 @@
#endif /* CONFIG_POWER */
#ifdef CONFIG_LCD
+static int board_dp_bridge_setup(void)
+{
+ const int max_tries = 10;
+ int num_tries, node;
+
+ /*
+ * TODO(sjg): Use device tree for GPIOs when exynos GPIO
+ * numbering patch is in mainline.
+ */
+ debug("%s\n", __func__);
+ node = fdtdec_next_compatible(gd->fdt_blob, 0, COMPAT_NXP_PTN3460);
+ if (node < 0) {
+ debug("%s: No node for DP bridge in device tree\n", __func__);
+ return -ENODEV;
+ }
+
+ /* Setup the GPIOs */
+
+ /* PD is ACTIVE_LOW, and initially de-asserted */
+ gpio_set_pull(EXYNOS5_GPIO_Y25, S5P_GPIO_PULL_NONE);
+ gpio_direction_output(EXYNOS5_GPIO_Y25, 1);
+
+ /* Reset is ACTIVE_LOW */
+ gpio_set_pull(EXYNOS5_GPIO_X15, S5P_GPIO_PULL_NONE);
+ gpio_direction_output(EXYNOS5_GPIO_X15, 0);
+
+ udelay(10);
+ gpio_set_value(EXYNOS5_GPIO_X15, 1);
+
+ gpio_direction_input(EXYNOS5_GPIO_X07);
+
+ /*
+ * We need to wait for 90ms after bringing up the bridge since there
+ * is a phantom "high" on the HPD chip during its bootup. The phantom
+ * high comes within 7ms of de-asserting PD and persists for at least
+ * 15ms. The real high comes roughly 50ms after PD is de-asserted. The
+ * phantom high makes it hard for us to know when the NXP chip is up.
+ */
+ mdelay(90);
+
+ for (num_tries = 0; num_tries < max_tries; num_tries++) {
+ /* Check HPD. If it's high, we're all good. */
+ if (gpio_get_value(EXYNOS5_GPIO_X07))
+ return 0;
+
+ debug("%s: eDP bridge failed to come up; try %d of %d\n",
+ __func__, num_tries, max_tries);
+ }
+
+ /* Immediately go into bridge reset if the hp line is not high */
+ return -ENODEV;
+}
+
void exynos_cfg_lcd_gpio(void)
{
/* For Backlight */
@@ -198,4 +251,49 @@
{
set_dp_phy_ctrl(onoff);
}
+
+void exynos_backlight_on(unsigned int on)
+{
+ debug("%s(%u)\n", __func__, on);
+
+ if (!on)
+ return;
+
+#ifdef CONFIG_POWER_TPS65090
+ int ret;
+
+ ret = tps65090_fet_enable(1); /* Enable FET1, backlight */
+ if (ret)
+ return;
+
+ /* T5 in the LCD timing spec (defined as > 10ms) */
+ mdelay(10);
+
+ /* board_dp_backlight_pwm */
+ gpio_direction_output(EXYNOS5_GPIO_B20, 1);
+
+ /* T6 in the LCD timing spec (defined as > 10ms) */
+ mdelay(10);
+
+ /* board_dp_backlight_en */
+ gpio_direction_output(EXYNOS5_GPIO_X30, 1);
+#endif
+}
+
+void exynos_lcd_power_on(void)
+{
+ int ret;
+
+ debug("%s\n", __func__);
+
+#ifdef CONFIG_POWER_TPS65090
+ /* board_dp_lcd_vdd */
+ tps65090_fet_enable(6); /* Enable FET6, lcd panel */
+#endif
+
+ ret = board_dp_bridge_setup();
+ if (ret && ret != -ENODEV)
+ printf("LCD bridge failed to enable: %d\n", ret);
+}
+
#endif