SAMSUNG: SMDKC100: Adds ethernet support.
Add setup for ethernet on SMDKC100, allowing kernel/ramdisk to be
loaded over tftp.
The preinit function will configure GPIO (GPK0CON) & SROMC to look
for environment in SROM Bank 3.
Signed-off-by: Naveen Krishna Ch <ch.naveen@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
diff --git a/board/samsung/smdkc100/smdkc100.c b/board/samsung/smdkc100/smdkc100.c
index 15a1a27..fb466c6 100644
--- a/board/samsung/smdkc100/smdkc100.c
+++ b/board/samsung/smdkc100/smdkc100.c
@@ -23,10 +23,40 @@
*/
#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/smc.h>
+#include <asm/arch/gpio.h>
+#include <netdev.h>
+
DECLARE_GLOBAL_DATA_PTR;
+/*
+ * Miscellaneous platform dependent initialisations
+ */
+static void smc9115_pre_init(void)
+{
+ u32 smc_bw_conf, smc_bc_conf;
+
+ struct s5pc100_gpio *const gpio =
+ (struct s5pc100_gpio *)S5PC100_GPIO_BASE;
+
+ /* gpio configuration GPK0CON */
+ gpio_cfg_pin(&gpio->gpio_k0, CONFIG_ENV_SROM_BANK, GPIO_FUNC(2));
+
+ /* Ethernet needs bus width of 16 bits */
+ smc_bw_conf = SMC_DATA16_WIDTH(CONFIG_ENV_SROM_BANK);
+ smc_bc_conf = SMC_BC_TACS(0x0) | SMC_BC_TCOS(0x4) | SMC_BC_TACC(0xe)
+ | SMC_BC_TCOH(0x1) | SMC_BC_TAH(0x4)
+ | SMC_BC_TACP(0x6) | SMC_BC_PMC(0x0);
+
+ /* Select and configure the SROMC bank */
+ s5pc1xx_config_sromc(CONFIG_ENV_SROM_BANK, smc_bw_conf, smc_bc_conf);
+}
+
int board_init(void)
{
+ smc9115_pre_init();
+
gd->bd->bi_arch_number = MACH_TYPE_SMDKC100;
gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
@@ -49,3 +79,12 @@
return 0;
}
#endif
+
+int board_eth_init(bd_t *bis)
+{
+ int rc = 0;
+#ifdef CONFIG_SMC911X
+ rc = smc911x_initialize(0, CONFIG_SMC911X_BASE);
+#endif
+ return rc;
+}
diff --git a/include/configs/smdkc100.h b/include/configs/smdkc100.h
index a8ba052..09bce6d 100644
--- a/include/configs/smdkc100.h
+++ b/include/configs/smdkc100.h
@@ -83,7 +83,6 @@
#undef CONFIG_CMD_FLASH
#undef CONFIG_CMD_IMLS
#undef CONFIG_CMD_NAND
-#undef CONFIG_CMD_NET
#define CONFIG_CMD_CACHE
#define CONFIG_CMD_REGINFO
@@ -235,4 +234,15 @@
#define CONFIG_DOS_PARTITION 1
+/*
+ * Ethernet Contoller driver
+ */
+#ifdef CONFIG_CMD_NET
+#define CONFIG_NET_MULTI
+#define CONFIG_SMC911X 1 /* we have a SMC9115 on-board */
+#define CONFIG_SMC911X_16_BIT 1 /* SMC911X_16_BIT Mode */
+#define CONFIG_SMC911X_BASE 0x98800300 /* SMC911X Drive Base */
+#define CONFIG_ENV_SROM_BANK 3 /* Select SROM Bank-3 for Ethernet*/
+#endif /* CONFIG_CMD_NET */
+
#endif /* __CONFIG_H */