ARM: OMAP5: Enable ABB configuration for MM voltage domain
Since we setup the voltage and frequency for the MM domain, we *must*
setup the ABB configuration needed for the domain as well. If we do not
do this, kernel configuring just the frequency using the default boot
loader configured voltage can fail on many corner lot units.
Reported-by: Richard Woodruff <r-woodruff2@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
diff --git a/arch/arm/cpu/armv7/omap-common/clocks-common.c b/arch/arm/cpu/armv7/omap-common/clocks-common.c
index 8fe695b..da57b38 100644
--- a/arch/arm/cpu/armv7/omap-common/clocks-common.c
+++ b/arch/arm/cpu/armv7/omap-common/clocks-common.c
@@ -632,6 +632,15 @@
val = optimize_vcore_voltage(&vcores->mm);
do_scale_vcore(vcores->mm.addr, val, vcores->mm.pmic);
+ /* Configure MM ABB LDO after scale */
+ abb_setup(vcores->mm.efuse.reg,
+ (*ctrl)->control_wkup_ldovbb_mm_voltage_ctrl,
+ (*prcm)->prm_abbldo_mm_setup,
+ (*prcm)->prm_abbldo_mm_ctrl,
+ (*prcm)->prm_irqstatus_mpu,
+ vcores->mm.abb_tx_done_mask,
+ OMAP_ABB_FAST_OPP);
+
val = optimize_vcore_voltage(&vcores->gpu);
do_scale_vcore(vcores->gpu.addr, val, vcores->gpu.pmic);
diff --git a/arch/arm/cpu/armv7/omap5/hw_data.c b/arch/arm/cpu/armv7/omap5/hw_data.c
index a4b31e4..dfb1df6 100644
--- a/arch/arm/cpu/armv7/omap5/hw_data.c
+++ b/arch/arm/cpu/armv7/omap5/hw_data.c
@@ -361,6 +361,7 @@
.mm.value = VDD_MM_ES2,
.mm.addr = SMPS_REG_ADDR_45_IVA,
.mm.pmic = &palmas,
+ .mm.abb_tx_done_mask = OMAP_ABB_MM_TXDONE_MASK,
};
struct vcores_data dra752_volts = {
diff --git a/arch/arm/cpu/armv7/omap5/prcm-regs.c b/arch/arm/cpu/armv7/omap5/prcm-regs.c
index c55c6af..d126a32 100644
--- a/arch/arm/cpu/armv7/omap5/prcm-regs.c
+++ b/arch/arm/cpu/armv7/omap5/prcm-regs.c
@@ -352,6 +352,7 @@
.control_emif1_sdram_config_ext = 0x4AE0C144,
.control_emif2_sdram_config_ext = 0x4AE0C148,
.control_wkup_ldovbb_mpu_voltage_ctrl = 0x4AE0C318,
+ .control_wkup_ldovbb_mm_voltage_ctrl = 0x4AE0C314,
.control_padconf_wkup_base = 0x4AE0C800,
.control_smart1nopmio_padconf_0 = 0x4AE0CDA0,
.control_smart1nopmio_padconf_1 = 0x4AE0CDA4,
@@ -722,6 +723,7 @@
.cm_l3init_usb_otg_ss1_clkctrl = 0x4a0096f0,
/* prm irqstatus regs */
+ .prm_irqstatus_mpu = 0x4ae06010,
.prm_irqstatus_mpu_2 = 0x4ae06014,
/* l4 wkup regs */
@@ -751,6 +753,8 @@
.prm_abbldo_mpu_setup = 0x4ae07cdc,
.prm_abbldo_mpu_ctrl = 0x4ae07ce0,
+ .prm_abbldo_mm_setup = 0x4ae07ce4,
+ .prm_abbldo_mm_ctrl = 0x4ae07ce8,
/* SCRM stuff, used by some boards */
.scrm_auxclk0 = 0x4ae0a310,
diff --git a/arch/arm/include/asm/arch-omap5/omap.h b/arch/arm/include/asm/arch-omap5/omap.h
index 1eeb8d5..cfec5b0 100644
--- a/arch/arm/include/asm/arch-omap5/omap.h
+++ b/arch/arm/include/asm/arch-omap5/omap.h
@@ -215,6 +215,7 @@
/* ABB tranxdone mask */
#define OMAP_ABB_MPU_TXDONE_MASK (0x1 << 7)
+#define OMAP_ABB_MM_TXDONE_MASK (0x1 << 31)
/* ABB efuse masks */
#define OMAP5_ABB_FUSE_VSET_MASK (0x1F << 24)
diff --git a/arch/arm/include/asm/omap_common.h b/arch/arm/include/asm/omap_common.h
index d3e8417..14c07fa 100644
--- a/arch/arm/include/asm/omap_common.h
+++ b/arch/arm/include/asm/omap_common.h
@@ -234,6 +234,7 @@
u32 cm_l3init_usb_otg_ss1_clkctrl;
u32 cm_l3init_usb_otg_ss2_clkctrl;
+ u32 prm_irqstatus_mpu;
u32 prm_irqstatus_mpu_2;
/* cm2.l4per */
@@ -321,6 +322,8 @@
u32 prm_vc_cfg_i2c_clk;
u32 prm_abbldo_mpu_setup;
u32 prm_abbldo_mpu_ctrl;
+ u32 prm_abbldo_mm_setup;
+ u32 prm_abbldo_mm_ctrl;
u32 cm_div_m4_dpll_core;
u32 cm_div_m5_dpll_core;
@@ -441,6 +444,7 @@
u32 control_emif1_sdram_config_ext;
u32 control_emif2_sdram_config_ext;
u32 control_wkup_ldovbb_mpu_voltage_ctrl;
+ u32 control_wkup_ldovbb_mm_voltage_ctrl;
u32 control_smart1nopmio_padconf_0;
u32 control_smart1nopmio_padconf_1;
u32 control_padconf_mode;