fsl/sleep: updated the deep sleep framework for QorIQ platforms
With the introducing of generic board and ARM-based cores, current
deep sleep framework doesn't work anymore.
This patch will convert the current framework to adapt this change.
Basically it does:
1. Converts all the Freescale's DDR driver to support deep sleep.
2. Added basic framework support for ARM-based and PPC-based
cores separately.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
diff --git a/drivers/ddr/fsl/arm_ddr_gen3.c b/drivers/ddr/fsl/arm_ddr_gen3.c
index 59f2fd6..c139da6 100644
--- a/drivers/ddr/fsl/arm_ddr_gen3.c
+++ b/drivers/ddr/fsl/arm_ddr_gen3.c
@@ -92,7 +92,6 @@
ddr_out32(&ddr->timing_cfg_0, regs->timing_cfg_0);
ddr_out32(&ddr->timing_cfg_1, regs->timing_cfg_1);
ddr_out32(&ddr->timing_cfg_2, regs->timing_cfg_2);
- ddr_out32(&ddr->sdram_cfg_2, regs->ddr_sdram_cfg_2);
ddr_out32(&ddr->sdram_mode, regs->ddr_sdram_mode);
ddr_out32(&ddr->sdram_mode_2, regs->ddr_sdram_mode_2);
ddr_out32(&ddr->sdram_mode_3, regs->ddr_sdram_mode_3);
@@ -105,9 +104,6 @@
ddr_out32(&ddr->sdram_interval, regs->ddr_sdram_interval);
ddr_out32(&ddr->sdram_data_init, regs->ddr_data_init);
ddr_out32(&ddr->sdram_clk_cntl, regs->ddr_sdram_clk_cntl);
- ddr_out32(&ddr->init_addr, regs->ddr_init_addr);
- ddr_out32(&ddr->init_ext_addr, regs->ddr_init_ext_addr);
-
ddr_out32(&ddr->timing_cfg_4, regs->timing_cfg_4);
ddr_out32(&ddr->timing_cfg_5, regs->timing_cfg_5);
ddr_out32(&ddr->ddr_zq_cntl, regs->ddr_zq_cntl);
@@ -128,7 +124,24 @@
ddr_out32(&ddr->ddr_sdram_rcw_1, regs->ddr_sdram_rcw_1);
ddr_out32(&ddr->ddr_sdram_rcw_2, regs->ddr_sdram_rcw_2);
ddr_out32(&ddr->ddr_cdr1, regs->ddr_cdr1);
- ddr_out32(&ddr->ddr_cdr2, regs->ddr_cdr2);
+#ifdef CONFIG_DEEP_SLEEP
+ if (is_warm_boot()) {
+ ddr_out32(&ddr->sdram_cfg_2,
+ regs->ddr_sdram_cfg_2 & ~SDRAM_CFG2_D_INIT);
+ ddr_out32(&ddr->init_addr, CONFIG_SYS_SDRAM_BASE);
+ ddr_out32(&ddr->init_ext_addr, DDR_INIT_ADDR_EXT_UIA);
+
+ /* DRAM VRef will not be trained */
+ ddr_out32(&ddr->ddr_cdr2,
+ regs->ddr_cdr2 & ~DDR_CDR2_VREF_TRAIN_EN);
+ } else
+#endif
+ {
+ ddr_out32(&ddr->sdram_cfg_2, regs->ddr_sdram_cfg_2);
+ ddr_out32(&ddr->init_addr, regs->ddr_init_addr);
+ ddr_out32(&ddr->init_ext_addr, regs->ddr_init_ext_addr);
+ ddr_out32(&ddr->ddr_cdr2, regs->ddr_cdr2);
+ }
ddr_out32(&ddr->err_disable, regs->err_disable);
ddr_out32(&ddr->err_int_en, regs->err_int_en);
for (i = 0; i < 32; i++) {
@@ -167,8 +180,20 @@
udelay(500);
asm volatile("dsb sy;isb");
+#ifdef CONFIG_DEEP_SLEEP
+ if (is_warm_boot()) {
+ /* enter self-refresh */
+ temp_sdram_cfg = ddr_in32(&ddr->sdram_cfg_2);
+ temp_sdram_cfg |= SDRAM_CFG2_FRC_SR;
+ ddr_out32(&ddr->sdram_cfg_2, temp_sdram_cfg);
+ /* do board specific memory setup */
+ board_mem_sleep_setup();
+
+ temp_sdram_cfg = (ddr_in32(&ddr->sdram_cfg) | SDRAM_CFG_BI);
+ } else
+#endif
+ temp_sdram_cfg = ddr_in32(&ddr->sdram_cfg) & ~SDRAM_CFG_BI;
/* Let the controller go */
- temp_sdram_cfg = ddr_in32(&ddr->sdram_cfg) & ~SDRAM_CFG_BI;
ddr_out32(&ddr->sdram_cfg, temp_sdram_cfg | SDRAM_CFG_MEM_EN);
asm volatile("dsb sy;isb");
@@ -211,4 +236,12 @@
if (timeout <= 0)
printf("Waiting for D_INIT timeout. Memory may not work.\n");
+#ifdef CONFIG_DEEP_SLEEP
+ if (is_warm_boot()) {
+ /* exit self-refresh */
+ temp_sdram_cfg = ddr_in32(&ddr->sdram_cfg_2);
+ temp_sdram_cfg &= ~SDRAM_CFG2_FRC_SR;
+ ddr_out32(&ddr->sdram_cfg_2, temp_sdram_cfg);
+ }
+#endif
}