arm: mvebu: db-88f6820: Add SPL support with DDR init code
This patch adds SPL support for the Marvell DB-88F6820-GP board.
With this change, the bin_hdr from the original Marvell U-boot
is not needed any more on this board. The sources from bin_hdr
(SERDES/PHY and DDR setup) are now integrated in mainline
U-Boot. And this patch enables them for this board.
Signed-off-by: Stefan Roese <sr@denx.de>
diff --git a/board/Marvell/db-88f6820-gp/README b/board/Marvell/db-88f6820-gp/README
new file mode 100644
index 0000000..9bea5b3
--- /dev/null
+++ b/board/Marvell/db-88f6820-gp/README
@@ -0,0 +1,18 @@
+Update from original Marvell U-Boot to mainline U-Boot:
+-------------------------------------------------------
+
+The resulting image including the SPL binary with the
+full DDR setup is "u-boot-spl.kwb".
+
+To update the SPI NOR flash, please use the following
+command:
+
+=> sf probe;tftpboot 2000000 db-88f6820-gp/u-boot-spl.kwb;\
+sf update 2000000 0 60000
+
+Note that the original Marvell U-Boot seems to have
+problems with the "sf update" command. This does not
+work reliable. So here this command should be used:
+
+=> sf probe;tftpboot 2000000 db-88f6820-gp/u-boot-spl.kwb;\
+sf erase 0 60000;sf write 2000000 0 60000
diff --git a/board/Marvell/db-88f6820-gp/db-88f6820-gp.c b/board/Marvell/db-88f6820-gp/db-88f6820-gp.c
index 51ac495..e661fa1 100644
--- a/board/Marvell/db-88f6820-gp/db-88f6820-gp.c
+++ b/board/Marvell/db-88f6820-gp/db-88f6820-gp.c
@@ -11,6 +11,8 @@
#include <asm/arch/cpu.h>
#include <asm/arch/soc.h>
+#include "../drivers/ddr/marvell/a38x/ddr3_a38x_topology.h"
+
DECLARE_GLOBAL_DATA_PTR;
#define BIT(nr) (1UL << (nr))
@@ -54,6 +56,35 @@
{ 0x21, 3, 0xC0 } /* Output Data, register#1 */
};
+/*
+ * Define the DDR layout / topology here in the board file. This will
+ * be used by the DDR3 init code in the SPL U-Boot version to configure
+ * the DDR3 controller.
+ */
+static struct hws_topology_map board_topology_map = {
+ 0x1, /* active interfaces */
+ /* cs_mask, mirror, dqs_swap, ck_swap X PUPs */
+ { { { {0x1, 0, 0, 0},
+ {0x1, 0, 0, 0},
+ {0x1, 0, 0, 0},
+ {0x1, 0, 0, 0},
+ {0x1, 0, 0, 0} },
+ SPEED_BIN_DDR_1866L, /* speed_bin */
+ BUS_WIDTH_8, /* memory_width */
+ MEM_4G, /* mem_size */
+ DDR_FREQ_800, /* frequency */
+ 0, 0, /* cas_l cas_wl */
+ HWS_TEMP_LOW} }, /* temperature */
+ 5, /* Num Of Bus Per Interface*/
+ BUS_MASK_32BIT /* Busses mask */
+};
+
+struct hws_topology_map *ddr3_get_topology_map(void)
+{
+ /* Return the board topology as defined in the board code */
+ return &board_topology_map;
+}
+
int board_early_init_f(void)
{
/* Configure MPP */
diff --git a/board/Marvell/db-88f6820-gp/kwbimage.cfg b/board/Marvell/db-88f6820-gp/kwbimage.cfg
index e812454..cc05792 100644
--- a/board/Marvell/db-88f6820-gp/kwbimage.cfg
+++ b/board/Marvell/db-88f6820-gp/kwbimage.cfg
@@ -9,4 +9,4 @@
BOOT_FROM spi
# Binary Header (bin_hdr) with DDR3 training code
-BINARY board/Marvell/db-88f6820-gp/binary.0 0000005b 00000068
+BINARY spl/u-boot-spl.bin 0000005b 00000068
diff --git a/configs/db-88f6820-gp_defconfig b/configs/db-88f6820-gp_defconfig
index 569ddfd..0ff6706 100644
--- a/configs/db-88f6820-gp_defconfig
+++ b/configs/db-88f6820-gp_defconfig
@@ -1,3 +1,4 @@
+CONFIG_SPL=y
CONFIG_ARM=y
CONFIG_TARGET_DB_88F6820_GP=y
# CONFIG_CMD_IMLS is not set
diff --git a/include/configs/db-88f6820-gp.h b/include/configs/db-88f6820-gp.h
index a429107..73b3236 100644
--- a/include/configs/db-88f6820-gp.h
+++ b/include/configs/db-88f6820-gp.h
@@ -11,6 +11,7 @@
* High Level Configuration Options (easy to change)
*/
#define CONFIG_ARMADA_XP /* SOC Family Name */
+#define CONFIG_ARMADA_38X
#define CONFIG_DB_88F6820_GP /* Board target name for DDR training */
#define CONFIG_SYS_L2_PL310
@@ -108,6 +109,40 @@
"fdt_high=0x10000000\0" \
"initrd_high=0x10000000\0"
+/* SPL */
+/* Defines for SPL */
+#define CONFIG_SPL_FRAMEWORK
+#define CONFIG_SPL_SIZE (140 << 10)
+#define CONFIG_SPL_TEXT_BASE 0x40000030
+#define CONFIG_SPL_MAX_SIZE (CONFIG_SPL_SIZE - 0x0030)
+
+#define CONFIG_SPL_BSS_START_ADDR (0x40000000 + CONFIG_SPL_SIZE)
+#define CONFIG_SPL_BSS_MAX_SIZE (16 << 10)
+
+#define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SPL_BSS_START_ADDR + \
+ CONFIG_SPL_BSS_MAX_SIZE)
+#define CONFIG_SYS_SPL_MALLOC_SIZE (16 << 10)
+
+#define CONFIG_SPL_STACK (0x40000000 + ((192 - 16) << 10))
+#define CONFIG_SPL_BOOTROM_SAVE (CONFIG_SPL_STACK + 4)
+
+#define CONFIG_SPL_LIBCOMMON_SUPPORT
+#define CONFIG_SPL_LIBGENERIC_SUPPORT
+#define CONFIG_SPL_SERIAL_SUPPORT
+#define CONFIG_SPL_I2C_SUPPORT
+
+/* SPL related SPI defines */
+#define CONFIG_SPL_SPI_SUPPORT
+#define CONFIG_SPL_SPI_FLASH_SUPPORT
+#define CONFIG_SPL_SPI_LOAD
+#define CONFIG_SPL_SPI_BUS 0
+#define CONFIG_SPL_SPI_CS 0
+#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x20000
+
+/* Enable DDR support in SPL (DDR3 training from Marvell bin_hdr) */
+#define CONFIG_SYS_MVEBU_DDR_A38X
+#define CONFIG_DDR3
+
/*
* mv-common.h should be defined after CMD configs since it used them
* to enable certain macros