diff --git a/board/Synology/ds109/kwbimage.cfg b/board/Synology/ds109/kwbimage.cfg
index 19d77e3..d544af5 100644
--- a/board/Synology/ds109/kwbimage.cfg
+++ b/board/Synology/ds109/kwbimage.cfg
@@ -19,7 +19,10 @@
 # Maximum KWBIMAGE_MAX_CONFIG configurations allowed
 
 # Configure RGMII-0/1 interface pad voltage to 1.8V
-DATA 0xFFD100e0 0x1b1b9b9b
+DATA 0xFFD100e0 0x1b1b1b9b
+
+DATA 0xFFD20134 0xbbbbbbbb
+DATA 0xFFD20138 0x00bbbbbb
 
 #Dram initalization for SINGLE x16 CL=5 @ 400MHz
 DATA 0xFFD01400 0x43000c30	# DDR Configuration register
@@ -30,7 +33,7 @@
 # bit29-26: zero
 # bit31-30: 01
 
-DATA 0xFFD01404 0x37543000	# DDR Controller Control Low
+DATA 0xFFD01404 0x39543000	# DDR Controller Control Low
 # bit 4:    0=addr/cmd in smame cycle
 # bit 5:    0=clk is driven during self refresh, we don't care for APX
 # bit 6:    0=use recommended falling edge of clk for addr/cmd
@@ -52,14 +55,14 @@
 # bit27-24: TRRD
 # bit31-28: TRTP
 
-DATA 0xFFD0140C 0x00000a33	#  DDR Timing (High)
+DATA 0xFFD0140C 0x00000833	#  DDR Timing (High)
 # bit6-0:   TRFC
 # bit8-7:   TR2R
 # bit10-9:  TR2W
 # bit12-11: TW2W
 # bit31-13: zero required
 
-DATA 0xFFD01410 0x000000cc	#  DDR Address Control
+DATA 0xFFD01410 0x0000000d	#  DDR Address Control
 # bit1-0:   01, Cs0width=x8
 # bit3-2:   10, Cs0size=1Gb
 # bit5-4:   01, Cs1width=x8
@@ -92,7 +95,7 @@
 # bit12:    0, PD must be zero
 # bit31-13: 0 required
 
-DATA 0xFFD01420 0x00000040	#  DDR Extended Mode
+DATA 0xFFD01420 0x00000042	#  DDR Extended Mode
 # bit0:    0,  DDR DLL enabled
 # bit1:    0,  DDR drive strenght normal
 # bit2:    0,  DDR ODT control lsd (disabled)
@@ -104,7 +107,7 @@
 # bit12:   0, DDR output buffer enabled
 # bit31-13: 0 required
 
-DATA 0xFFD01424 0x0000F17F	#  DDR Controller Control High
+DATA 0xFFD01424 0x0000F1FF	#  DDR Controller Control High
 # bit2-0:  111, required
 # bit3  :  1  , MBUS Burst Chop disabled
 # bit6-4:  111, required
@@ -120,26 +123,28 @@
 DATA 0xFFD0147C 0x00008552	# DDR2 ODT Write Timing (default values)
 
 DATA 0xFFD01500 0x00000000	# CS[0]n Base address to 0x0
-DATA 0xFFD01504 0x0FFFFFF1	# CS[0]n Size
+DATA 0xFFD01504 0x07FFFFF1	# CS[0]n Size
 # bit0:    1,  Window enabled
 # bit1:    0,  Write Protect disabled
 # bit3-2:  00, CS0 hit selected
 # bit23-4: ones, required
-# bit31-24: 0x0F, Size (i.e. 256MB)
+# bit31-24: 0x07, Size (i.e. 128MB)
 
 DATA 0xFFD01508 0x10000000	# CS[1]n Base address to 256Mb
-DATA 0xFFD0150C 0x0FFFFFF5	# CS[1]n Size 256Mb Window enabled for CS1
+DATA 0xFFD0150C 0x00000000	# CS[1]n Size, window disabled
 
+DATA 0xFFD01510 0x20000000	# CS[2]n Base address to 256Mb
 DATA 0xFFD01514 0x00000000	# CS[2]n Size, window disabled
+DATA 0xFFD01518 0x30000000	# CS[3]n Base address to 256Mb
 DATA 0xFFD0151C 0x00000000	# CS[3]n Size, window disabled
 
-DATA 0xFFD01494 0x00030000	#  DDR ODT Control (Low)
+DATA 0xFFD01494 0x003C0000	#  DDR ODT Control (Low)
 DATA 0xFFD01498 0x00000000	#  DDR ODT Control (High)
 # bit1-0:  00, ODT0 controlled by ODT Control (low) register above
 # bit3-2:  01, ODT1 active NEVER!
 # bit31-4: zero, required
 
-DATA 0xFFD0149C 0x0000E803	# CPU ODT Control
+DATA 0xFFD0149C 0x0000F80F	# CPU ODT Control
 DATA 0xFFD01480 0x00000001	# DDR Initialization Control
 #bit0=1, enable DDR init upon this register write