powerpc: T1024RDB: Remove macro CONFIG_T1024RDB
Use TARGET_T1024RDB from Kconfig instead.
Signed-off-by: York Sun <york.sun@nxp.com>
[trini: Get missing hunk in board/freescale/t102xrdb/ddr.c]
Signed-off-by: Tom Rini <trini@konsulko.com>
diff --git a/board/freescale/t102xrdb/Makefile b/board/freescale/t102xrdb/Makefile
index 6452865..ddeb44f 100644
--- a/board/freescale/t102xrdb/Makefile
+++ b/board/freescale/t102xrdb/Makefile
@@ -8,7 +8,7 @@
obj-y += spl.o
else
obj-y += t102xrdb.o
-obj-$(CONFIG_T1024RDB) += cpld.o
+obj-$(CONFIG_TARGET_T1024RDB) += cpld.o
obj-y += eth_t102xrdb.o
obj-$(CONFIG_PCI) += pci.o
endif
diff --git a/board/freescale/t102xrdb/ddr.c b/board/freescale/t102xrdb/ddr.c
index c09199f..e666578 100644
--- a/board/freescale/t102xrdb/ddr.c
+++ b/board/freescale/t102xrdb/ddr.c
@@ -140,7 +140,7 @@
popts->wrlvl_ctl_2 = 0x07070606;
popts->half_strength_driver_enable = 1;
popts->cpo_sample = 0x43;
-#elif defined(CONFIG_T1024RDB)
+#elif defined(CONFIG_TARGET_T1024RDB)
/* optimize cpo for erratum A-009942 */
popts->cpo_sample = 0x52;
#endif
diff --git a/board/freescale/t102xrdb/eth_t102xrdb.c b/board/freescale/t102xrdb/eth_t102xrdb.c
index dadfaf1..c06d1b8 100644
--- a/board/freescale/t102xrdb/eth_t102xrdb.c
+++ b/board/freescale/t102xrdb/eth_t102xrdb.c
@@ -58,7 +58,7 @@
fm_info_set_phy_address(FM1_DTSEC4, RGMII_PHY1_ADDR);
switch (srds_s1) {
-#ifdef CONFIG_T1024RDB
+#ifdef CONFIG_TARGET_T1024RDB
case 0x95:
/* set the on-board RGMII2 PHY */
fm_info_set_phy_address(FM1_DTSEC3, RGMII_PHY2_ADDR);
@@ -94,7 +94,7 @@
case PHY_INTERFACE_MODE_SGMII:
#if defined(CONFIG_TARGET_T1023RDB)
dev = miiphy_get_dev_by_name(DEFAULT_FM_MDIO_NAME);
-#elif defined(CONFIG_T1024RDB)
+#elif defined(CONFIG_TARGET_T1024RDB)
dev = miiphy_get_dev_by_name(DEFAULT_FM_TGEC_MDIO_NAME);
#endif
fm_info_set_mdio(i, dev);
@@ -128,7 +128,7 @@
void board_ft_fman_fixup_port(void *fdt, char *compat, phys_addr_t addr,
enum fm_port port, int offset)
{
-#if defined(CONFIG_T1024RDB)
+#if defined(CONFIG_TARGET_T1024RDB)
if (((fm_info_get_enet_if(port) == PHY_INTERFACE_MODE_SGMII_2500) ||
(fm_info_get_enet_if(port) == PHY_INTERFACE_MODE_SGMII)) &&
(port == FM1_DTSEC3)) {
diff --git a/board/freescale/t102xrdb/t102xrdb.c b/board/freescale/t102xrdb/t102xrdb.c
index 3174726..56f7c1a 100644
--- a/board/freescale/t102xrdb/t102xrdb.c
+++ b/board/freescale/t102xrdb/t102xrdb.c
@@ -17,7 +17,7 @@
#include <asm/fsl_liodn.h>
#include <fm_eth.h>
#include "t102xrdb.h"
-#ifdef CONFIG_T1024RDB
+#ifdef CONFIG_TARGET_T1024RDB
#include "cpld.h"
#elif defined(CONFIG_TARGET_T1023RDB)
#include <i2c.h>
@@ -51,7 +51,7 @@
srds_s1 >>= FSL_CORENET2_RCWSR4_SRDS1_PRTCL_SHIFT;
printf("Board: %sRDB, ", cpu->name);
-#if defined(CONFIG_T1024RDB)
+#if defined(CONFIG_TARGET_T1024RDB)
printf("Board rev: 0x%02x CPLD ver: 0x%02x, ",
CPLD_READ(hw_ver), CPLD_READ(sw_ver));
#elif defined(CONFIG_TARGET_T1023RDB)
@@ -63,7 +63,7 @@
puts("SD/MMC\n");
#elif CONFIG_SPIFLASH
puts("SPI\n");
-#elif defined(CONFIG_T1024RDB)
+#elif defined(CONFIG_TARGET_T1024RDB)
u8 reg;
reg = CPLD_READ(flash_csr);
@@ -91,7 +91,7 @@
return 0;
}
-#ifdef CONFIG_T1024RDB
+#ifdef CONFIG_TARGET_T1024RDB
static void board_mux_lane(void)
{
ccsr_gur_t __iomem *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
@@ -150,7 +150,7 @@
0, flash_esel, BOOKE_PAGESZ_256M, 1);
#endif
-#ifdef CONFIG_T1024RDB
+#ifdef CONFIG_TARGET_T1024RDB
board_mux_lane();
#endif