diff --git a/board/omap2420h4/omap2420h4.c b/board/omap2420h4/omap2420h4.c
new file mode 100644
index 0000000..4696a71
--- /dev/null
+++ b/board/omap2420h4/omap2420h4.c
@@ -0,0 +1,834 @@
+/*
+ * (C) Copyright 2004
+ * Texas Instruments, <www.ti.com>
+ * Richard Woodruff <r-woodruff2@ti.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+#include <common.h>
+#include <asm/arch/omap2420.h>
+#include <asm/io.h>
+#include <asm/arch/bits.h>
+#include <asm/arch/mux.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/arch/sys_info.h>
+#include <asm/arch/mem.h>
+#include <i2c.h>
+#include <asm/mach-types.h>
+
+static void wait_for_command_complete(unsigned int wd_base);
+
+/*******************************************************
+ * Routine: delay
+ * Description: spinning delay to use before udelay works
+ ******************************************************/
+static inline void delay (unsigned long loops)
+{
+	__asm__ volatile ("1:\n"
+					  "subs %0, %1, #1\n"
+					  "bne 1b":"=r" (loops):"0" (loops));
+}
+
+/*****************************************
+ * Routine: board_init
+ * Description: Early hardware init.
+ *****************************************/
+int board_init (void)
+{
+	DECLARE_GLOBAL_DATA_PTR;
+#ifndef CONFIG_PARTIAL_SRAM
+	s_init(0x0);  /* full sram build, never skip clock and sdrc, no point */
+#else
+	gpmc_init();
+#endif
+	gd->bd->bi_arch_number = MACH_TYPE_OMAP_H4;		/* board id for linux */
+	gd->bd->bi_boot_params = (OMAP2420_SDRC_CS0+0x100);	/* adress of boot parameters */
+
+	return 0;
+}
+
+/**********************************************************
+ * Routine: s_init
+ * Description: Does early system init of muxing and clocks.
+ * - Called at time when only stack is available.
+ **********************************************************/
+void s_init(int skip)
+{
+	watchdog_init();
+	set_muxconf_regs();
+	delay(100);
+
+	if (!skip)
+		prcm_init();
+
+	peripheral_enable();
+	icache_enable();
+#ifndef CONFIG_APTIX
+	if (!skip)
+		memif_init();
+#endif
+}
+
+/*******************************************************
+ * Routine: misc_init_r
+ * Description: Init ethernet (done here so udelay works)
+ ********************************************************/
+int misc_init_r (void)
+{
+	ether_init(); /* better done here so timers are init'ed */
+	return(0);
+}
+
+/****************************************
+ * Routine: watchdog_init
+ * Description: Shut down watch dogs
+ *****************************************/
+void watchdog_init(void)
+{
+	int mode;
+#define GP (BIT8|BIT9)
+
+	/* There are 4 watch dogs.  1 secure, and 3 general purpose.
+	 * I would expect that the ROM takes care of the secure one,
+	 * but we will try also.  Of the 3 GP ones, 1 can reset us
+	 * directly, the other 2 only generate MPU interrupts.
+	 */
+	mode = (__raw_readl(CONTROL_STATUS) & (BIT8|BIT9));
+	if (mode == GP) {
+		__raw_writel(WD_UNLOCK1 ,WD1_BASE+WSPR);
+		wait_for_command_complete(WD1_BASE);
+		__raw_writel(WD_UNLOCK2 ,WD1_BASE+WSPR);
+	}
+	__raw_writel(WD_UNLOCK1 ,WD2_BASE+WSPR);
+	wait_for_command_complete(WD2_BASE);
+	__raw_writel(WD_UNLOCK2 ,WD2_BASE+WSPR);
+
+#if MPU_WD_CLOCKED /* value 0x10 stick on aptix, BIT4 polarity seems oppsite*/
+	__raw_writel(WD_UNLOCK1 ,WD3_BASE+WSPR);
+	wait_for_command_complete(WD3_BASE);
+	__raw_writel(WD_UNLOCK2 ,WD3_BASE+WSPR);
+
+	__raw_writel(WD_UNLOCK1 ,WD4_BASE+WSPR);
+	wait_for_command_complete(WD4_BASE);
+	__raw_writel(WD_UNLOCK2 ,WD4_BASE+WSPR);
+#endif
+}
+
+/******************************************************
+ * Routine: wait_for_command_complete
+ * Description: Wait for posting to finish on watchdog
+ ******************************************************/
+static void wait_for_command_complete(unsigned int wd_base)
+{
+	int pending = 1;
+	do {
+		pending = __raw_readl(wd_base+WWPS);
+	} while (pending);
+}
+
+/*******************************************************************
+ * Routine:ether_init
+ * Description: take the Ethernet controller out of reset and wait
+ *  		   for the EEPROM load to complete.
+ ******************************************************************/
+void ether_init (void)
+{
+#ifdef CONFIG_DRIVER_LAN91C96
+	int cnt = 20;
+
+	__raw_writew(0x0, LAN_RESET_REGISTER);
+	do {
+		__raw_writew(0x1, LAN_RESET_REGISTER);
+		udelay (100);
+		if (cnt == 0)
+			goto h4reset_err_out;
+		--cnt;
+	} while (__raw_readw(LAN_RESET_REGISTER) != 0x1);
+
+	cnt = 20;
+
+	do {
+		__raw_writew(0x0, LAN_RESET_REGISTER);
+		udelay (100);
+		if (cnt == 0)
+			goto h4reset_err_out;
+		--cnt;
+	} while (__raw_readw(LAN_RESET_REGISTER) != 0x0000);
+	udelay (1000);
+
+	*((volatile unsigned char *) ETH_CONTROL_REG) &= ~0x01;
+	udelay (1000);
+
+	h4reset_err_out:
+	return;
+#endif
+}
+
+/**********************************************
+ * Routine: dram_init
+ * Description: sets uboots idea of sdram size
+ **********************************************/
+int dram_init (void)
+{
+	DECLARE_GLOBAL_DATA_PTR;
+	unsigned int size0=0,size1=0;
+	u32 mtype, btype;
+#define NOT_EARLY 0
+
+	i2c_init (CFG_I2C_SPEED, CFG_I2C_SLAVE); /* need this a bit early */
+
+	btype = get_board_type();
+	mtype = get_mem_type();
+
+	display_board_info(btype);
+	if (btype == BOARD_H4_MENELAUS)
+		update_mux(btype,mtype);
+
+	if ((mtype == DDR_COMBO) || (mtype == DDR_STACKED)) {
+		do_sdrc_init(SDRC_CS1_OSET, NOT_EARLY);	/* init other chip select */
+		size0 = size1 = SZ_32M;
+	} else
+		size0 = SZ_64M;
+
+	gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
+	gd->bd->bi_dram[0].size = size0;
+	gd->bd->bi_dram[1].start = PHYS_SDRAM_2;
+	gd->bd->bi_dram[1].size = size1;
+
+	return 0;
+}
+
+/**********************************************************
+ * Routine: set_muxconf_regs
+ * Description: Setting up the configuration Mux registers
+ *              specific to the hardware
+ *********************************************************/
+void set_muxconf_regs (void)
+{
+	muxSetupSDRC();
+	muxSetupGPMC();
+	muxSetupUsb0();
+	muxSetupUart3();
+	muxSetupI2C1();
+	muxSetupUART1();
+	muxSetupLCD();
+	muxSetupCamera();
+	muxSetupMMCSD();
+	muxSetupTouchScreen();
+	muxSetupHDQ();
+}
+
+/*****************************************************************
+ * Routine: peripheral_enable
+ * Description: Enable the clks & power for perifs (GPT2, UART1,...)
+ ******************************************************************/
+void peripheral_enable(void)
+{
+	unsigned int v, if_clks=0, func_clks=0;
+
+	/* Enable GP2 timer.*/
+	if_clks |= BIT4;
+	func_clks |= BIT4;
+	v = __raw_readl(CM_CLKSEL2_CORE) | 0x4;	/* Sys_clk input OMAP2420_GPT2 */
+	__raw_writel(v, CM_CLKSEL2_CORE);
+	__raw_writel(0x1, CM_CLKSEL_WKUP);
+
+#ifdef CFG_NS16550
+	/* Enable UART1 clock */
+	func_clks |= BIT21;
+	if_clks |= BIT21;
+#endif
+	v = __raw_readl(CM_ICLKEN1_CORE) | if_clks;	/* Interface clocks on */
+	__raw_writel(v,CM_ICLKEN1_CORE );
+	v = __raw_readl(CM_FCLKEN1_CORE) | func_clks; /* Functional Clocks on */
+	__raw_writel(v, CM_FCLKEN1_CORE);
+	delay(1000);
+
+#ifndef KERNEL_UPDATED
+	{
+#define V1 0xffffffff
+#define V2 0x00000007
+
+		__raw_writel(V1, CM_FCLKEN1_CORE);
+		__raw_writel(V2, CM_FCLKEN2_CORE);
+		__raw_writel(V1, CM_ICLKEN1_CORE);
+		__raw_writel(V1, CM_ICLKEN2_CORE);
+	}
+#endif
+}
+
+/****************************************
+ * Routine: muxSetupUsb0   (ostboot)
+ * Description: Setup usb muxing
+ *****************************************/
+void muxSetupUsb0(void)
+{
+	volatile uint8   *MuxConfigReg;
+	volatile uint32  *otgCtrlReg;
+
+	MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_USB0_PUEN;
+	*MuxConfigReg &= (uint8)(~0x1F);
+
+	MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_USB0_VP;
+	*MuxConfigReg &= (uint8)(~0x1F);
+
+	MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_USB0_VM;
+	*MuxConfigReg &= (uint8)(~0x1F);
+
+	MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_USB0_RCV;
+	*MuxConfigReg &= (uint8)(~0x1F);
+
+	MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_USB0_TXEN;
+	*MuxConfigReg &= (uint8)(~0x1F);
+
+	MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_USB0_SE0;
+	*MuxConfigReg &= (uint8)(~0x1F);
+
+	MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_USB0_DAT;
+	*MuxConfigReg &= (uint8)(~0x1F);
+
+	/* setup for USB VBus detection */
+	otgCtrlReg = (volatile uint32 *)USB_OTG_CTRL;
+	*otgCtrlReg |= 0x00040000; /* bit 18 */
+}
+
+/****************************************
+ * Routine: muxSetupUart3   (ostboot)
+ * Description: Setup uart3 muxing
+ *****************************************/
+void muxSetupUart3(void)
+{
+	volatile uint8 *MuxConfigReg;
+
+	MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_UART3_TX_IRTX;
+	*MuxConfigReg &= (uint8)(~0x1F);
+
+	MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_UART3_RX_IRRX;
+	*MuxConfigReg &= (uint8)(~0x1F);
+}
+
+/****************************************
+ * Routine: muxSetupI2C1   (ostboot)
+ * Description: Setup i2c muxing
+ *****************************************/
+void muxSetupI2C1(void)
+{
+	volatile unsigned char  *MuxConfigReg;
+
+	/* I2C1 Clock pin configuration, PIN = M19 */
+	MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_I2C1_SCL;
+	*MuxConfigReg = 0x00 ; // Mode = 0, PUPD=Disabled
+
+	/* I2C1 Data pin configuration, PIN = L15 */
+	MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_I2C1_SDA;
+	*MuxConfigReg = 0x00 ; // Mode = 0, PUPD=Disabled
+
+	/* Pull-up required on data line */
+	/* external pull-up already present. */
+	/* *MuxConfigReg |= 0x18 ;*/ /* Mode = 0, PullTypeSel=PU, PullUDEnable=Enabled */
+}
+
+/****************************************
+ * Routine: muxSetupUART1  (ostboot)
+ * Description: Set up uart1 muxing
+ *****************************************/
+void muxSetupUART1(void)
+{
+	volatile unsigned char  *MuxConfigReg;
+
+	/* UART1_CTS pin configuration, PIN = D21 */
+	MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_UART1_CTS;
+	*MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
+
+	/* UART1_RTS pin configuration, PIN = H21 */
+	MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_UART1_RTS;
+	*MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
+
+	/* UART1_TX pin configuration, PIN = L20 */
+	MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_UART1_TX;
+	*MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
+
+	/* UART1_RX pin configuration, PIN = T21 */
+	MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_UART1_RX;
+	*MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
+}
+
+/****************************************
+ * Routine: muxSetupLCD   (ostboot)
+ * Description: Setup lcd muxing
+ *****************************************/
+void muxSetupLCD(void)
+{
+	volatile unsigned char  *MuxConfigReg;
+
+	/* LCD_D0 pin configuration, PIN = Y7  */
+	MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D0;
+	*MuxConfigReg = 0x00 ; // Mode = 0, PUPD=Disabled
+
+	/* LCD_D1 pin configuration, PIN = P10 */
+	MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D1;
+	*MuxConfigReg = 0x00 ; // Mode = 0, PUPD=Disabled
+
+	/* LCD_D2 pin configuration, PIN = V8  */
+	MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D2;
+	*MuxConfigReg = 0x00 ; // Mode = 0, PUPD=Disabled
+
+	/* LCD_D3 pin configuration, PIN = Y8  */
+	MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D3;
+	*MuxConfigReg = 0x00 ; // Mode = 0, PUPD=Disabled
+
+	/* LCD_D4 pin configuration, PIN = W8  */
+	MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D4;
+	*MuxConfigReg = 0x00 ; // Mode = 0, PUPD=Disabled
+
+	/* LCD_D5 pin configuration, PIN = R10 */
+	MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D5;
+	*MuxConfigReg = 0x00 ; // Mode = 0, PUPD=Disabled
+
+	/* LCD_D6 pin configuration, PIN = Y9  */
+	MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D6;
+	*MuxConfigReg = 0x00 ; // Mode = 0, PUPD=Disabled
+
+	/* LCD_D7 pin configuration, PIN = V9  */
+	MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D7;
+	*MuxConfigReg = 0x00 ; // Mode = 0, PUPD=Disabled
+
+	/* LCD_D8 pin configuration, PIN = W9  */
+	MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D8;
+	*MuxConfigReg = 0x00 ; // Mode = 0, PUPD=Disabled
+
+	/* LCD_D9 pin configuration, PIN = P11 */
+	MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D9;
+	*MuxConfigReg = 0x00 ; // Mode = 0, PUPD=Disabled
+
+	/* LCD_D10 pin configuration, PIN = V10 */
+	MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D10;
+	*MuxConfigReg = 0x00 ; // Mode = 0, PUPD=Disabled
+
+	/* LCD_D11 pin configuration, PIN = Y10 */
+	MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D11;
+	*MuxConfigReg = 0x00 ; // Mode = 0, PUPD=Disabled
+
+	/* LCD_D12 pin configuration, PIN = W10 */
+	MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D12;
+	*MuxConfigReg = 0x00 ; // Mode = 0, PUPD=Disabled
+
+	/* LCD_D13 pin configuration, PIN = R11 */
+	MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D13;
+	*MuxConfigReg = 0x00 ; // Mode = 0, PUPD=Disabled
+
+	/* LCD_D14 pin configuration, PIN = V11 */
+	MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D14;
+	*MuxConfigReg = 0x00 ; // Mode = 0, PUPD=Disabled
+
+	/* LCD_D15 pin configuration, PIN = W11 */
+	MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D15;
+	*MuxConfigReg = 0x00 ; // Mode = 0, PUPD=Disabled
+
+	/* LCD_D16 pin configuration, PIN = P12 */
+	MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D16;
+	*MuxConfigReg = 0x00 ; // Mode = 0, PUPD=Disabled
+
+	/* LCD_D17 pin configuration, PIN = R12 */
+	MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D17;
+	*MuxConfigReg = 0x00 ; // Mode = 0, PUPD=Disabled
+
+	/* LCD_PCLK pin configuration,   PIN = W6   */
+	MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_PCLK;
+	*MuxConfigReg = 0x00 ; // Mode = 0, PUPD=Disabled
+
+	/* LCD_VSYNC pin configuration,  PIN = V7  */
+	MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_VSYNC;
+	*MuxConfigReg = 0x00 ; // Mode = 0, PUPD=Disabled
+
+	/* LCD_HSYNC pin configuration,  PIN = Y6  */
+	MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_HSYNC;
+	*MuxConfigReg = 0x00 ; // Mode = 0, PUPD=Disabled
+
+	/* LCD_ACBIAS pin configuration, PIN = W7 */
+	MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_ACBIAS;
+	*MuxConfigReg = 0x00 ; // Mode = 0, PUPD=Disabled
+}
+
+/****************************************
+ * Routine: muxSetupCamera  (ostboot)
+ * Description: Setup camera muxing
+ *****************************************/
+void muxSetupCamera(void)
+{
+	volatile unsigned char  *MuxConfigReg;
+
+	/* CAMERA_RSTZ  pin configuration, PIN = Y16 */
+	/* CAM_RST is connected through the I2C IO expander.*/
+	/* MuxConfigReg = (volatile unsigned char *), CONTROL_PADCONF_SYS_NRESWARM*/
+	/* *MuxConfigReg = 0x00 ; // Mode = 0, PUPD=Disabled   */
+
+	/* CAMERA_XCLK  pin configuration, PIN = U3 */
+	MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_CAM_XCLK;
+	*MuxConfigReg = 0x00 ; // Mode = 0, PUPD=Disabled
+
+	/* CAMERA_LCLK  pin configuration, PIN = V5 */
+	MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_CAM_LCLK;
+	*MuxConfigReg = 0x00 ; // Mode = 0, PUPD=Disabled
+
+	/* CAMERA_VSYNC pin configuration, PIN = U2 */
+	MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_CAM_VS,
+				   *MuxConfigReg = 0x00 ; // Mode = 0, PUPD=Disabled
+
+	/* CAMERA_HSYNC pin configuration, PIN = T3 */
+	MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_CAM_HS,
+				   *MuxConfigReg = 0x00 ; // Mode = 0, PUPD=Disabled
+
+	/* CAMERA_DAT0 pin configuration, PIN = T4 */
+	MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_CAM_D0,
+				   *MuxConfigReg = 0x00 ; // Mode = 0, PUPD=Disabled
+
+	/* CAMERA_DAT1 pin configuration, PIN = V2 */
+	MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_CAM_D1,
+				   *MuxConfigReg = 0x00 ; // Mode = 0, PUPD=Disabled
+
+	/* CAMERA_DAT2 pin configuration, PIN = V3 */
+	MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_CAM_D2,
+				   *MuxConfigReg = 0x00 ; // Mode = 0, PUPD=Disabled
+
+	/* CAMERA_DAT3 pin configuration, PIN = U4 */
+	MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_CAM_D3,
+				   *MuxConfigReg = 0x00 ; // Mode = 0, PUPD=Disabled
+
+	/* CAMERA_DAT4 pin configuration, PIN = W2 */
+	MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_CAM_D4,
+				   *MuxConfigReg = 0x00 ; // Mode = 0, PUPD=Disabled
+
+	/* CAMERA_DAT5 pin configuration, PIN = V4 */
+	MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_CAM_D5,
+				   *MuxConfigReg = 0x00 ; // Mode = 0, PUPD=Disabled
+
+	/* CAMERA_DAT6 pin configuration, PIN = W3 */
+	MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_CAM_D6,
+				   *MuxConfigReg = 0x00 ; // Mode = 0, PUPD=Disabled
+
+	/* CAMERA_DAT7 pin configuration, PIN = Y2 */
+	MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_CAM_D7,
+				   *MuxConfigReg = 0x00 ; // Mode = 0, PUPD=Disabled
+
+	/* CAMERA_DAT8 pin configuration, PIN = Y4 */
+	MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_CAM_D8,
+				   *MuxConfigReg = 0x00 ; // Mode = 0, PUPD=Disabled
+
+	/* CAMERA_DAT9 pin configuration, PIN = V6 */
+	MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_CAM_D9,
+				   *MuxConfigReg = 0x00 ; // Mode = 0, PUPD=Disabled
+}
+
+/****************************************
+ * Routine: muxSetupMMCSD (ostboot)
+ * Description: set up MMC muxing
+ *****************************************/
+void muxSetupMMCSD(void)
+{
+	volatile unsigned char  *MuxConfigReg;
+
+	/* SDMMC_CLKI pin configuration,  PIN = H15 */
+	MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_MMC_CLKI,
+				   *MuxConfigReg = 0x00 ; // Mode = 0, PUPD=Disabled
+
+	/* SDMMC_CLKO pin configuration,  PIN = G19 */
+	MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_MMC_CLKO,
+				   *MuxConfigReg = 0x00 ; // Mode = 0, PUPD=Disabled
+
+	/* SDMMC_CMD pin configuration,   PIN = H18 */
+	MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_MMC_CMD,
+				   *MuxConfigReg = 0x00 ; // Mode = 0, PUPD=Disabled
+	// External pull-ups are present.
+	// *MuxConfigReg |= 0x18 ; // PullUDEnable=Enabled, PullTypeSel=PU
+
+	/* SDMMC_DAT0 pin configuration,  PIN = F20 */
+	MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_MMC_DAT0,
+				   *MuxConfigReg = 0x00 ; // Mode = 0, PUPD=Disabled
+	// External pull-ups are present.
+	// *MuxConfigReg |= 0x18 ; // PullUDEnable=Enabled, PullTypeSel=PU
+
+	/* SDMMC_DAT1 pin configuration,  PIN = H14 */
+	MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_MMC_DAT1,
+				   *MuxConfigReg = 0x00 ; // Mode = 0, PUPD=Disabled
+	// External pull-ups are present.
+	// *MuxConfigReg |= 0x18 ; // PullUDEnable=Enabled, PullTypeSel=PU
+
+	/* SDMMC_DAT2 pin configuration,  PIN = E19 */
+	MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_MMC_DAT2,
+				   *MuxConfigReg = 0x00 ; // Mode = 0, PUPD=Disabled
+	// External pull-ups are present.
+	// *MuxConfigReg |= 0x18 ; // PullUDEnable=Enabled, PullTypeSel=PU
+
+	/* SDMMC_DAT3 pin configuration,  PIN = D19 */
+	MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_MMC_DAT3,
+				   *MuxConfigReg = 0x00 ; // Mode = 0, PUPD=Disabled
+	// External pull-ups are present.
+	// *MuxConfigReg |= 0x18 ; // PullUDEnable=Enabled, PullTypeSel=PU
+
+	/* SDMMC_DDIR0 pin configuration, PIN = F19 */
+	MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_MMC_DAT_DIR0,
+				   *MuxConfigReg = 0x00 ; // Mode = 0, PUPD=Disabled
+
+	/* SDMMC_DDIR1 pin configuration, PIN = E20 */
+	MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_MMC_DAT_DIR1,
+				   *MuxConfigReg = 0x00 ; // Mode = 0, PUPD=Disabled
+
+	/* SDMMC_DDIR2 pin configuration, PIN = F18 */
+	MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_MMC_DAT_DIR2,
+				   *MuxConfigReg = 0x00 ; // Mode = 0, PUPD=Disabled
+
+	/* SDMMC_DDIR3 pin configuration, PIN = E18 */
+	MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_MMC_DAT_DIR3,
+				   *MuxConfigReg = 0x00 ; // Mode = 0, PUPD=Disabled
+
+	/* SDMMC_CDIR pin configuration,  PIN = G18 */
+	MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_MMC_CMD_DIR,
+				   *MuxConfigReg = 0x00 ; // Mode = 0, PUPD=Disabled
+
+	/* MMC_CD pin configuration,      PIN = B3  ---2420IP ONLY---*/
+	/* MMC_CD for 2422IP=K1 */
+	MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_SDRC_A14,
+				   *MuxConfigReg = 0x03 ; // Mode = 3, PUPD=Disabled
+
+	/* MMC_WP pin configuration,      PIN = B4  */
+	MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_SDRC_A13,
+				   *MuxConfigReg = 0x03 ; // Mode = 3, PUPD=Disabled
+}
+
+/******************************************
+ * Routine: muxSetupTouchScreen (ostboot)
+ * Description:  Set up touch screen muxing
+ *******************************************/
+void muxSetupTouchScreen(void)
+{
+	volatile unsigned char  *MuxConfigReg;
+
+	/* SPI1_CLK pin configuration,  PIN = U18 */
+	MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_SPI1_CLK,
+				   *MuxConfigReg = 0x00 ; // Mode = 0, PUPD=Disabled
+
+	/* SPI1_MOSI pin configuration, PIN = V20 */
+	MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_SPI1_SIMO,
+				   *MuxConfigReg = 0x00 ; // Mode = 0, PUPD=Disabled
+
+	/* SPI1_MISO pin configuration, PIN = T18 */
+	MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_SPI1_SOMI,
+				   *MuxConfigReg = 0x00 ; // Mode = 0, PUPD=Disabled
+
+	/* SPI1_nCS0 pin configuration, PIN = U19 */
+	MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_SPI1_NCS0,
+				   *MuxConfigReg = 0x00 ; // Mode = 0, PUPD=Disabled
+
+	/* PEN_IRQ pin configuration,   PIN = P20 */
+	MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_MCBSP1_FSR,
+				   *MuxConfigReg = 0x03 ; // Mode = 3, PUPD=Disabled
+}
+
+/****************************************
+ * Routine: muxSetupHDQ (ostboot)
+ * Description: setup 1wire mux
+ *****************************************/
+void muxSetupHDQ(void)
+{
+	volatile unsigned char  *MuxConfigReg;
+
+	/* HDQ_SIO pin configuration,  PIN = N18 */
+	MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_HDQ_SIO,
+				   *MuxConfigReg = 0x00 ; // Mode = 0, PUPD=Disabled
+}
+
+/***************************************************************
+ * Routine: muxSetupGPMC (ostboot)
+ * Description: Configures balls which cam up in protected mode
+ ***************************************************************/
+void muxSetupGPMC(void)
+{
+	volatile uint8 *MuxConfigReg;
+	volatile unsigned int *MCR = 0x4800008C;
+
+	/* gpmc_io_dir */
+	*MCR = 0x19000000;
+
+	/* NOR FLASH CS0 */
+	/* signal - Gpmc_clk; pin - J4; offset - 0x0088; mode - 0; Byte-3	Pull/up - N/A */
+	MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_GPMC_D2_BYTE3,
+				   *MuxConfigReg = 0x00 ;
+
+	/* signal - Gpmc_iodir; pin - n2; offset - 0x008C; mode - 1; Byte-3	Pull/up - N/A */
+	MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_GPMC_NCS0_BYTE3,
+				   *MuxConfigReg = 0x01 ;
+
+	/* MPDB(Multi Port Debug Port) CS1 */
+	/* signal - gpmc_ncs1; pin - N8; offset - 0x008C; mode - 0; Byte-1	Pull/up - N/A */
+	MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_GPMC_NCS0_BYTE1,
+				   *MuxConfigReg = 0x00 ;
+
+	/* signal - Gpmc_ncs2; pin - E2; offset - 0x008C; mode - 0; Byte-2	Pull/up - N/A */
+	MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_GPMC_NCS0_BYTE2,
+				   *MuxConfigReg = 0x00 ;
+
+
+}
+
+/****************************************************************
+ * Routine: muxSetupSDRC  (ostboot)
+ * Description: Configures balls which come up in protected mode
+ ****************************************************************/
+void muxSetupSDRC(void)
+{
+	volatile uint8 *MuxConfigReg;
+
+	/* signal - sdrc_ncs1; pin - C12; offset - 0x00A0; mode - 0; Byte-1	Pull/up - N/A */
+	MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_SDRC_NCS0_BYTE1,
+				   *MuxConfigReg = 0x00 ;
+
+	/* signal - sdrc_a12; pin - D11; offset - 0x0030; mode - 0; Byte-2	Pull/up - N/A */
+	MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_SDRC_A14_BYTE2,
+				   *MuxConfigReg = 0x00 ;
+
+	/* signal - sdrc_cke1; pin - B13; offset - 0x00A0; mode - 0; Byte-3	Pull/up - N/A */
+	MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_SDRC_NCS0_BYTE3,
+				   *MuxConfigReg = 0x00;
+
+	if (get_cpu_type() == CPU_2422) {
+		MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_SDRC_A14_BYTE0,
+					   *MuxConfigReg = 0x1b;
+	}
+}
+
+/*****************************************************************************
+ * Routine: update_mux()
+ * Description: Update balls which are different beween boards.  All should be
+ *              updated to match functionaly.  However, I'm only updating ones
+ *              which I'll be using for now.  When power comes into play they
+ *              all need updating.
+ *****************************************************************************/
+void update_mux(u32 btype,u32 mtype)
+{
+	u32 cpu, base = OMAP2420_CTRL_BASE;
+	cpu = get_cpu_type();
+
+	if (btype == BOARD_H4_MENELAUS) {
+		if (cpu == CPU_2420) {
+			/* PIN = B3,  GPIO.0->KBR5,      mode 3,  (pun?),-DO-*/
+			__raw_writeb(0x3, base+0x30);
+			/* PIN = B13, GPIO.38->KBC6,     mode 3,  (pun?)-DO-*/
+			__raw_writeb(0x3, base+0xa3);
+			/* PIN = F1, GPIO.25->HSUSBxx    mode 3,  (for external HS USB)*/
+			/* PIN = H1, GPIO.26->HSUSBxx    mode 3,  (for external HS USB)*/
+			/* PIN = K1, GPMC_ncs6           mode 0,  (on board nand access)*/
+			/* PIN = L2, GPMC_ncs67          mode 0,  (for external HS USB)*/
+			/* PIN = M1 (HSUSBOTG) */
+			/* PIN = P1, GPIO.35->MEN_POK    mode 3,  (menelaus powerok)-DO-*/
+			__raw_writeb(0x3, base+0x9d);
+			/* PIN = U32, (WLAN_CLKREQ) */
+			/* PIN = Y11, WLAN */
+			/* PIN = AA4, GPIO.15->KBC2,     mode 3,  -DO- */
+			__raw_writeb(0x3, base+0xe7);
+			/* PIN = AA8, mDOC */
+			/* PIN = AA10, BT */
+			/* PIN = AA13, WLAN */
+			/* PIN = M18 GPIO.96->MMC2_WP    mode 3   -DO- */
+			__raw_writeb(0x3, base+0x10e);
+			/* PIN = N19 GPIO.98->WLAN_INT   mode 3   -DO- */
+			__raw_writeb(0x3, base+0x110);
+			/* PIN = J15 HHUSB */
+			/* PIN = H19 HSUSB */
+			/* PIN = W13, P13, R13, W16 ... */
+			/* PIN = V12 GPIO.25->I2C_CAMEN  mode 3   -DO- */
+			__raw_writeb(0x3, base+0xde);
+			/* PIN = W19 sys_nirq->MENELAUS_INT mode 0 -DO- */
+			__raw_writeb(0x0, base+0x12c);
+			/* PIN = AA17->sys_clkreq        mode 0   -DO- */
+			__raw_writeb(0x0, base+0x136);
+		} else if (cpu == CPU_2422) {
+			/* PIN = B3,  GPIO.0->nc,        mode 3,  set above (pun?)*/
+			/* PIN = B13, GPIO.cke1->nc,     mode 0,  set above, (pun?)*/
+			/* PIN = F1, GPIO.25->HSUSBxx    mode 3,  (for external HS USB)*/
+			/* PIN = H1, GPIO.26->HSUSBxx    mode 3,  (for external HS USB)*/
+			/* PIN = K1, GPMC_ncs6           mode 0,  (on board nand access)*/
+			__raw_writeb(0x0, base+0x92);
+			/* PIN = L2, GPMC_ncs67          mode 0,  (for external HS USB)*/
+			/* PIN = M1 (HSUSBOTG) */
+			/* PIN = P1, GPIO.35->MEN_POK    mode 3,  (menelaus powerok)-DO-*/
+			__raw_writeb(0x3, base+0x10c);
+			/* PIN = U32, (WLAN_CLKREQ) */
+			/* PIN = AA4, GPIO.15->KBC2,     mode 3,  -DO- */
+			__raw_writeb(0x3, base+0x30);
+			/* PIN = AA8, mDOC */
+			/* PIN = AA10, BT */
+			/* PIN = AA12, WLAN */
+			/* PIN = M18 GPIO.96->MMC2_WP    mode 3   -DO- */
+			__raw_writeb(0x3, base+0x10e);
+			/* PIN = N19 GPIO.98->WLAN_INT   mode 3   -DO- */
+			__raw_writeb(0x3, base+0x110);
+			/* PIN = J15 HHUSB */
+			/* PIN = H19 HSUSB */
+			/* PIN = W13, P13, R13, W16 ... */
+			/* PIN = V12 GPIO.25->I2C_CAMEN  mode 3   -DO- */
+			__raw_writeb(0x3, base+0xde);
+			/* PIN = W19 sys_nirq->MENELAUS_INT mode 0 -DO- */
+			__raw_writeb(0x0, base+0x12c);
+			/* PIN = AA17->sys_clkreq        mode 0   -DO- */
+			__raw_writeb(0x0, base+0x136);
+		}
+
+	} else if (btype == BOARD_H4_SDP) {
+		if (cpu == CPU_2420) {
+			/* PIN = B3,  GPIO.0->nc         mode 3,  set above (pun?)*/
+			/* PIN = B13, GPIO.cke1->nc,     mode 0,  set above, (pun?)*/
+			/* Pin = Y11 VLNQ */
+			/* Pin = AA4 VLNQ */
+			/* Pin = AA6 VLNQ */
+			/* Pin = AA8 VLNQ */
+			/* Pin = AA10 VLNQ */
+			/* Pin = AA12 VLNQ */
+			/* PIN = M18 GPIO.96->KBR5       mode 3   -DO- */
+			__raw_writeb(0x3, base+0x10e);
+			/* PIN = N19 GPIO.98->KBC6       mode 3   -DO- */
+			__raw_writeb(0x3, base+0x110);
+			/* PIN = J15 MDOC_nDMAREQ */
+			/* PIN = H19 GPIO.100->KBC2      mode 3   -DO- */
+			__raw_writeb(0x3, base+0x114);
+			/* PIN = W13, V12, P13, R13, W19, W16 ... */
+			/* PIN = AA17 sys_clkreq->bt_clk_req  mode 0  */
+		} else if (cpu == CPU_2422) {
+			/* PIN = B3,  GPIO.0->MMC_CD,    mode 3,  set above */
+			/* PIN = B13, GPIO.38->wlan_int, mode 3,  (pun?)*/
+			/* Pin = Y11 VLNQ */
+			/* Pin = AA4 VLNQ */
+			/* Pin = AA6 VLNQ */
+			/* Pin = AA8 VLNQ */
+			/* Pin = AA10 VLNQ */
+			/* Pin = AA12 VLNQ */
+			/* PIN = M18 GPIO.96->KBR5       mode 3   -DO- */
+			__raw_writeb(0x3, base+0x10e);
+			/* PIN = N19 GPIO.98->KBC6       mode 3   -DO- */
+			__raw_writeb(0x3, base+0x110);
+			/* PIN = J15 MDOC_nDMAREQ */
+			/* PIN = H19 GPIO.100->KBC2      mode 3   -DO- */
+			__raw_writeb(0x3, base+0x114);
+			/* PIN = W13, V12, P13, R13, W19, W16 ... */
+			/* PIN = AA17 sys_clkreq->bt_clk_req  mode 0 */
+		}
+	}
+}
+
+