* Code cleanup:
- remove trailing white space, trailing empty lines, C++ comments, etc.
- split cmd_boot.c (separate cmd_bdinfo.c and cmd_load.c)
* Patches by Kenneth Johansson, 25 Jun 2003:
- major rework of command structure
(work done mostly by Michal Cendrowski and Joakim Kristiansen)
diff --git a/board/cray/L1/init.S b/board/cray/L1/init.S
index acc5205..72a10d3 100644
--- a/board/cray/L1/init.S
+++ b/board/cray/L1/init.S
@@ -52,53 +52,53 @@
/* control registers to set that up are determined by what we've */
/* empirically discovered work there. */
- .globl ext_bus_cntlr_init
+ .globl ext_bus_cntlr_init
ext_bus_cntlr_init:
- mflr r4 /* save link register */
- bl ..getAddr
+ mflr r4 /* save link register */
+ bl ..getAddr
..getAddr:
- mflr r3 /* get address of ..getAddr */
- mtlr r4 /* restore link register */
- addi r4,0,14 /* set ctr to 10; used to prefetch */
- mtctr r4 /* 10 cache lines to fit this function */
- /* in cache (gives us 8x10=80 instrctns) */
+ mflr r3 /* get address of ..getAddr */
+ mtlr r4 /* restore link register */
+ addi r4,0,14 /* set ctr to 10; used to prefetch */
+ mtctr r4 /* 10 cache lines to fit this function */
+ /* in cache (gives us 8x10=80 instrctns) */
..ebcloop:
- icbt r0,r3 /* prefetch cache line for addr in r3 */
- addi r3,r3,32 /* move to next cache line */
- bdnz ..ebcloop /* continue for 10 cache lines */
+ icbt r0,r3 /* prefetch cache line for addr in r3 */
+ addi r3,r3,32 /* move to next cache line */
+ bdnz ..ebcloop /* continue for 10 cache lines */
- /*------------------------------------------------------------------- */
- /* Delay to ensure all accesses to ROM are complete before changing */
+ /*------------------------------------------------------------------- */
+ /* Delay to ensure all accesses to ROM are complete before changing */
/* bank 0 timings. 200usec should be enough. */
- /* 200,000,000 (cycles/sec) X .000200 (sec) = 0x9C40 cycles */
- /*------------------------------------------------------------------- */
+ /* 200,000,000 (cycles/sec) X .000200 (sec) = 0x9C40 cycles */
+ /*------------------------------------------------------------------- */
addis r3,0,0x0
- ori r3,r3,0xA000 /* ensure 200usec have passed since reset */
- mtctr r3
+ ori r3,r3,0xA000 /* ensure 200usec have passed since reset */
+ mtctr r3
..spinlp:
- bdnz ..spinlp /* spin loop */
+ bdnz ..spinlp /* spin loop */
- /*---------------------------------------------------------------------- */
- /* Peripheral Bank 0 (Flash) initialization */
- /*---------------------------------------------------------------------- */
+ /*---------------------------------------------------------------------- */
+ /* Peripheral Bank 0 (Flash) initialization */
+ /*---------------------------------------------------------------------- */
/* 0x7F8FFE80 slowest boot */
- addi r4,0,pb0ap
- mtdcr ebccfga,r4
- addis r4,0,0x9B01
- ori r4,r4,0x5480
- mtdcr ebccfgd,r4
+ addi r4,0,pb0ap
+ mtdcr ebccfga,r4
+ addis r4,0,0x9B01
+ ori r4,r4,0x5480
+ mtdcr ebccfgd,r4
- addi r4,0,pb0cr
- mtdcr ebccfga,r4
- addis r4,0,0xFFC5 /* BAS=0xFFC,BS=0x4(4MB),BU=0x3(R/W), */
- ori r4,r4,0x8000 /* BW=0x0( 8 bits) */
- mtdcr ebccfgd,r4
+ addi r4,0,pb0cr
+ mtdcr ebccfga,r4
+ addis r4,0,0xFFC5 /* BAS=0xFFC,BS=0x4(4MB),BU=0x3(R/W), */
+ ori r4,r4,0x8000 /* BW=0x0( 8 bits) */
+ mtdcr ebccfgd,r4
- blr
+ blr
- /*---------------------------------------------------------------------- */
- /* Peripheral Bank 1 (NVRAM/RTC) initialization */
+ /*---------------------------------------------------------------------- */
+ /* Peripheral Bank 1 (NVRAM/RTC) initialization */
/* CRAY:the L1 has NOT this bank, it is tied to SV2/IOCA/etc/ instead */
/* and we do DMA on it. The ConfigurationRegister part is threfore */
/* almost arbitrary, except that our linux driver needs to know the */
@@ -119,21 +119,21 @@
/* ByteEnableMode BEM=0 */
/* ParityEnable PEN=0 */
/* all reserved bits=0 */
- /*---------------------------------------------------------------------- */
- /*---------------------------------------------------------------------- */
- addi r4,0,pb1ap
- mtdcr ebccfga,r4
- addis r4,0,0x0185 /* hiword */
- ori r4,r4,0x4380 /* loword */
- mtdcr ebccfgd,r4
+ /*---------------------------------------------------------------------- */
+ /*---------------------------------------------------------------------- */
+ addi r4,0,pb1ap
+ mtdcr ebccfga,r4
+ addis r4,0,0x0185 /* hiword */
+ ori r4,r4,0x4380 /* loword */
+ mtdcr ebccfgd,r4
- addi r4,0,pb1cr
- mtdcr ebccfga,r4
- addis r4,0,0xF001 /* BAS=0xF00,BS=0x0(1MB),BU=0x3(R/W), */
- ori r4,r4,0x8000 /* BW=0x0( 8 bits) */
- mtdcr ebccfgd,r4
+ addi r4,0,pb1cr
+ mtdcr ebccfga,r4
+ addis r4,0,0xF001 /* BAS=0xF00,BS=0x0(1MB),BU=0x3(R/W), */
+ ori r4,r4,0x8000 /* BW=0x0( 8 bits) */
+ mtdcr ebccfgd,r4
- blr
+ blr
/*----------------------------------------------------------------------------- */
/* Function: sdram_init */
@@ -141,7 +141,7 @@
/* NOTE: for CrayL1 we have ECC memory, so enable it. */
/*....now done in C in L1.c:init_sdram for readability. */
/*----------------------------------------------------------------------------- */
- .globl sdram_init
+ .globl sdram_init
sdram_init:
blr