ppc4xx: AMCC Taihu board config file cleanup
This patch makes the AMCC Taihu a little more compatible to the other
AMCC eval boards.
Signed-off-by: Stefan Roese <sr@denx.de>
diff --git a/include/configs/taihu.h b/include/configs/taihu.h
index c51468b..d012c60 100644
--- a/include/configs/taihu.h
+++ b/include/configs/taihu.h
@@ -80,6 +80,7 @@
"bootfile=/tftpboot/taihu/uImage\0" \
"rootpath=/opt/eldk/ppc_4xx\0" \
"netdev=eth0\0" \
+ "hostname=taihu\0" \
"nfsargs=setenv bootargs root=/dev/nfs rw " \
"nfsroot=${serverip}:${rootpath}\0" \
"ramargs=setenv bootargs root=/dev/ram rw\0" \
@@ -210,10 +211,12 @@
#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
-#define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */
+#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
#define CONFIG_LOOPW 1 /* enable loopw command */
+#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
+#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
/*-----------------------------------------------------------------------
* I2C stuff
@@ -328,7 +331,7 @@
/*-----------------------------------------------------------------------
* PPC405 GPIO Configuration
*/
-#define CFG_440_GPIO_TABLE { /* GPIO Alternate1 */ \
+#define CFG_4xx_GPIO_TABLE { /* GPIO Alternate1 */ \
{ \
/* GPIO Core 0 */ \
{ GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO0 PerBLast SPI CS */ \
@@ -415,43 +418,6 @@
#define CFG_EBC_PB4AP 0x158FF600
#define CFG_EBC_PB4CR 0x5021A000
-/*-----------------------------------------------------------------------
- * Definitions for GPIO setup (PPC405EP specific)
- *
- * GPIO0[0] - External Bus Controller BLAST output
- * GPIO0[1-9] - Instruction trace outputs
- * GPIO0[10-13] - External Bus Controller CS_1 - CS_4 outputs
- * GPIO0[14-16] - External Bus Controller ABUS3-ABUS5 outputs
- * GPIO0[17-23] - External Interrupts IRQ0 - IRQ6 inputs
- * GPIO0[24-27] - UART0 control signal inputs/outputs
- * GPIO0[28-29] - UART1 data signal input/output
- * GPIO0[30-31] - EMAC0 and EMAC1 reject packet inputs
- */
-#define CFG_GPIO0_OSRH 0x15555550 /* output select high/low */
-#define CFG_GPIO0_OSRL 0x00000110
-#define CFG_GPIO0_ISR1H 0x00000001 /* input select high/low */
-#define CFG_GPIO0_ISR1L 0x15545440
-#define CFG_GPIO0_TSRH 0x00000000 /* three-state select high/low */
-#define CFG_GPIO0_TSRL 0x00000000
-#define CFG_GPIO0_TCR 0xFFFE8117 /* three-state control */
-#define CFG_GPIO0_ODR 0x00000000 /* open drain */
-
-#define GPIO0 0 /* GPIO controller 0 */
-
-/* the GPIO macros in include/ppc405.h for High/Low registers are backwards */
-
-#define GPIOx_OSL (GPIO0_OSRH-GPIO_BASE)
-#define GPIOx_TSL (GPIO0_TSRH-GPIO_BASE)
-#define GPIOx_IS1L (GPIO0_ISR1H-GPIO_BASE)
-#define GPIOx_IS2L (GPIO0_ISR1H-GPIO_BASE)
-#define GPIOx_IS3L (GPIO0_ISR1H-GPIO_BASE)
-
-#define GPIO_OS(x) (x+GPIOx_OSL) /* GPIO output select */
-#define GPIO_TS(x) (x+GPIOx_TSL) /* GPIO three-state select */
-#define GPIO_IS1(x) (x+GPIOx_IS1L) /* GPIO input select */
-#define GPIO_IS2(x) (x+GPIOx_IS1L)
-#define GPIO_IS3(x) (x+GPIOx_IS1L)
-
#define CPLD_REG0_ADDR 0x50100000
#define CPLD_REG1_ADDR 0x50100001
/*