am3517_evm: switch to musb-new
Use new musb framework instead of the old one on AM3517_EVM.
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
diff --git a/board/logicpd/am3517evm/am3517evm.c b/board/logicpd/am3517evm/am3517evm.c
index d316f33..0b3721e 100644
--- a/board/logicpd/am3517evm/am3517evm.c
+++ b/board/logicpd/am3517evm/am3517evm.c
@@ -25,12 +25,20 @@
#include <common.h>
#include <asm/io.h>
+#include <asm/omap_musb.h>
+#include <asm/arch/am35x_def.h>
#include <asm/arch/mem.h>
#include <asm/arch/mux.h>
#include <asm/arch/sys_proto.h>
#include <asm/arch/mmc_host_def.h>
+#include <asm/arch/musb.h>
#include <asm/mach-types.h>
+#include <asm/errno.h>
+#include <linux/usb/ch9.h>
+#include <linux/usb/gadget.h>
+#include <linux/usb/musb.h>
#include <i2c.h>
+#include <netdev.h>
#include "am3517evm.h"
DECLARE_GLOBAL_DATA_PTR;
@@ -50,6 +58,52 @@
return 0;
}
+#ifdef CONFIG_USB_MUSB_AM35X
+static struct musb_hdrc_config musb_config = {
+ .multipoint = 1,
+ .dyn_fifo = 1,
+ .num_eps = 16,
+ .ram_bits = 12,
+};
+
+static struct omap_musb_board_data musb_board_data = {
+ .set_phy_power = am35x_musb_phy_power,
+ .clear_irq = am35x_musb_clear_irq,
+ .reset = am35x_musb_reset,
+};
+
+static struct musb_hdrc_platform_data musb_plat = {
+#if defined(CONFIG_MUSB_HOST)
+ .mode = MUSB_HOST,
+#elif defined(CONFIG_MUSB_GADGET)
+ .mode = MUSB_PERIPHERAL,
+#else
+#error "Please define either CONFIG_MUSB_HOST or CONFIG_MUSB_GADGET"
+#endif
+ .config = &musb_config,
+ .power = 250,
+ .platform_ops = &am35x_ops,
+ .board_data = &musb_board_data,
+};
+
+static void am3517_evm_musb_init(void)
+{
+ /*
+ * Set up USB clock/mode in the DEVCONF2 register.
+ * USB2.0 PHY reference clock is 13 MHz
+ */
+ clrsetbits_le32(&am35x_scm_general_regs->devconf2,
+ CONF2_REFFREQ | CONF2_OTGMODE | CONF2_PHY_GPIOMODE,
+ CONF2_REFFREQ_13MHZ | CONF2_SESENDEN |
+ CONF2_VBDTCTEN | CONF2_DATPOL);
+
+ musb_register(&musb_plat, &musb_board_data,
+ (void *)AM35XX_IPSS_USBOTGSS_BASE);
+}
+#else
+#define am3517_evm_musb_init() do {} while (0)
+#endif
+
/*
* Routine: misc_init_r
* Description: Init i2c, ethernet, etc... (done here so udelay works)
@@ -62,6 +116,8 @@
dieid_num_r();
+ am3517_evm_musb_init();
+
return 0;
}
@@ -83,3 +139,21 @@
return 0;
}
#endif
+
+#if defined(CONFIG_USB_ETHER) && defined(CONFIG_MUSB_GADGET)
+int board_eth_init(bd_t *bis)
+{
+ int rv, n = 0;
+
+ rv = cpu_eth_init(bis);
+ if (rv > 0)
+ n += rv;
+
+ rv = usb_eth_initialize(bis);
+ if (rv > 0)
+ n += rv;
+
+ return n;
+}
+#endif
+