doc: board: Add QEMU x86 board doc
This extracts QEMU x86 board specific information from README.x86,
converts plain text documentation to reST format and adds it to
Sphinx TOC tree. No essential content change.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
diff --git a/doc/README.x86 b/doc/README.x86
index c987439..8cee320 100644
--- a/doc/README.x86
+++ b/doc/README.x86
@@ -57,99 +57,6 @@
---
-QEMU x86 target instructions for bare mode:
-
-To build u-boot.rom for QEMU x86 targets, just simply run
-
-$ make qemu-x86_defconfig (for 32-bit)
-or
-$ make qemu-x86_64_defconfig (for 64-bit)
-$ make all
-
-Note this default configuration will build a U-Boot for the QEMU x86 i440FX
-board. To build a U-Boot against QEMU x86 Q35 board, you can change the build
-configuration during the 'make menuconfig' process like below:
-
-Device Tree Control --->
- ...
- (qemu-x86_q35) Default Device Tree for DT control
-
-Test with QEMU for bare mode
-----------------------------
-QEMU is a fancy emulator that can enable us to test U-Boot without access to
-a real x86 board. Please make sure your QEMU version is 2.3.0 or above test
-U-Boot. To launch QEMU with u-boot.rom, call QEMU as follows:
-
-$ qemu-system-i386 -nographic -bios path/to/u-boot.rom
-
-This will instantiate an emulated x86 board with i440FX and PIIX chipset. QEMU
-also supports emulating an x86 board with Q35 and ICH9 based chipset, which is
-also supported by U-Boot. To instantiate such a machine, call QEMU with:
-
-$ qemu-system-i386 -nographic -bios path/to/u-boot.rom -M q35
-
-Note by default QEMU instantiated boards only have 128 MiB system memory. But
-it is enough to have U-Boot boot and function correctly. You can increase the
-system memory by pass '-m' parameter to QEMU if you want more memory:
-
-$ qemu-system-i386 -nographic -bios path/to/u-boot.rom -m 1024
-
-This creates a board with 1 GiB system memory. Currently U-Boot for QEMU only
-supports 3 GiB maximum system memory and reserves the last 1 GiB address space
-for PCI device memory-mapped I/O and other stuff, so the maximum value of '-m'
-would be 3072.
-
-QEMU emulates a graphic card which U-Boot supports. Removing '-nographic' will
-show QEMU's VGA console window. Note this will disable QEMU's serial output.
-If you want to check both consoles, use '-serial stdio'.
-
-Multicore is also supported by QEMU via '-smp n' where n is the number of cores
-to instantiate. Note, the maximum supported CPU number in QEMU is 255.
-
-The fw_cfg interface in QEMU also provides information about kernel data,
-initrd, command-line arguments and more. U-Boot supports directly accessing
-these informtion from fw_cfg interface, which saves the time of loading them
-from hard disk or network again, through emulated devices. To use it , simply
-providing them in QEMU command line:
-
-$ qemu-system-i386 -nographic -bios path/to/u-boot.rom -m 1024 -kernel /path/to/bzImage
- -append 'root=/dev/ram console=ttyS0' -initrd /path/to/initrd -smp 8
-
-Note: -initrd and -smp are both optional
-
-Then start QEMU, in U-Boot command line use the following U-Boot command to
-setup kernel:
-
- => qfw
-qfw - QEMU firmware interface
-
-Usage:
-qfw <command>
- - list : print firmware(s) currently loaded
- - cpus : print online cpu number
- - load <kernel addr> <initrd addr> : load kernel and initrd (if any) and setup for zboot
-
-=> qfw load
-loading kernel to address 01000000 size 5d9d30 initrd 04000000 size 1b1ab50
-
-Here the kernel (bzImage) is loaded to 01000000 and initrd is to 04000000. Then,
-'zboot' can be used to boot the kernel:
-
-=> zboot 01000000 - 04000000 1b1ab50
-
-To run 64-bit U-Boot, qemu-system-x86_64 should be used instead, e.g.:
-$ qemu-system-x86_64 -nographic -bios path/to/u-boot.rom
-
-A specific CPU can be specified via the '-cpu' parameter but please make
-sure the specified CPU supports 64-bit like '-cpu core2duo'. Conversely
-'-cpu pentium' won't work for obvious reasons that the processor only
-supports 32-bit.
-
-Note 64-bit support is very preliminary at this point. Lots of features
-are missing in the 64-bit world. One notable feature is the VGA console
-support which is currently missing, so that you must specify '-nographic'
-to get 64-bit U-Boot up and running.
-
CPU Microcode
-------------
Modern CPUs usually require a special bit stream called microcode [8] to be
diff --git a/doc/board/emulation/index.rst b/doc/board/emulation/index.rst
new file mode 100644
index 0000000..6d533f3
--- /dev/null
+++ b/doc/board/emulation/index.rst
@@ -0,0 +1,9 @@
+.. SPDX-License-Identifier: GPL-2.0+
+
+Emulation
+=========
+
+.. toctree::
+ :maxdepth: 2
+
+ qemu-x86
diff --git a/doc/board/emulation/qemu-x86.rst b/doc/board/emulation/qemu-x86.rst
new file mode 100644
index 0000000..c2e704a
--- /dev/null
+++ b/doc/board/emulation/qemu-x86.rst
@@ -0,0 +1,101 @@
+.. SPDX-License-Identifier: GPL-2.0+
+.. sectionauthor:: Bin Meng <bmeng.cn@gmail.com>
+
+QEMU x86
+========
+
+Build instructions for bare mode
+--------------------------------
+
+To build u-boot.rom for QEMU x86 targets, just simply run::
+
+ $ make qemu-x86_defconfig (for 32-bit)
+ $ make qemu-x86_64_defconfig (for 64-bit)
+ $ make all
+
+Note this default configuration will build a U-Boot for the QEMU x86 i440FX
+board. To build a U-Boot against QEMU x86 Q35 board, you can change the build
+configuration during the 'make menuconfig' process like below::
+
+ Device Tree Control --->
+ ...
+ (qemu-x86_q35) Default Device Tree for DT control
+
+Test with QEMU for bare mode
+----------------------------
+
+QEMU is a fancy emulator that can enable us to test U-Boot without access to
+a real x86 board. Please make sure your QEMU version is 2.3.0 or above test
+U-Boot. To launch QEMU with u-boot.rom, call QEMU as follows::
+
+ $ qemu-system-i386 -nographic -bios path/to/u-boot.rom
+
+This will instantiate an emulated x86 board with i440FX and PIIX chipset. QEMU
+also supports emulating an x86 board with Q35 and ICH9 based chipset, which is
+also supported by U-Boot. To instantiate such a machine, call QEMU with::
+
+ $ qemu-system-i386 -nographic -bios path/to/u-boot.rom -M q35
+
+Note by default QEMU instantiated boards only have 128 MiB system memory. But
+it is enough to have U-Boot boot and function correctly. You can increase the
+system memory by pass '-m' parameter to QEMU if you want more memory::
+
+ $ qemu-system-i386 -nographic -bios path/to/u-boot.rom -m 1024
+
+This creates a board with 1 GiB system memory. Currently U-Boot for QEMU only
+supports 3 GiB maximum system memory and reserves the last 1 GiB address space
+for PCI device memory-mapped I/O and other stuff, so the maximum value of '-m'
+would be 3072.
+
+QEMU emulates a graphic card which U-Boot supports. Removing '-nographic' will
+show QEMU's VGA console window. Note this will disable QEMU's serial output.
+If you want to check both consoles, use '-serial stdio'.
+
+Multicore is also supported by QEMU via '-smp n' where n is the number of cores
+to instantiate. Note, the maximum supported CPU number in QEMU is 255.
+
+The fw_cfg interface in QEMU also provides information about kernel data,
+initrd, command-line arguments and more. U-Boot supports directly accessing
+these informtion from fw_cfg interface, which saves the time of loading them
+from hard disk or network again, through emulated devices. To use it , simply
+providing them in QEMU command line::
+
+ $ qemu-system-i386 -nographic -bios path/to/u-boot.rom -m 1024 \
+ -kernel /path/to/bzImage -append 'root=/dev/ram console=ttyS0' \
+ -initrd /path/to/initrd -smp 8
+
+Note: -initrd and -smp are both optional
+
+Then start QEMU, in U-Boot command line use the following U-Boot command to
+setup kernel::
+
+ => qfw
+ qfw - QEMU firmware interface
+
+ Usage:
+ qfw <command>
+ - list : print firmware(s) currently loaded
+ - cpus : print online cpu number
+ - load <kernel addr> <initrd addr> : load kernel and initrd (if any) and setup for zboot
+
+ => qfw load
+ loading kernel to address 01000000 size 5d9d30 initrd 04000000 size 1b1ab50
+
+Here the kernel (bzImage) is loaded to 01000000 and initrd is to 04000000. Then,
+'zboot' can be used to boot the kernel::
+
+ => zboot 01000000 - 04000000 1b1ab50
+
+To run 64-bit U-Boot, qemu-system-x86_64 should be used instead, e.g.::
+
+ $ qemu-system-x86_64 -nographic -bios path/to/u-boot.rom
+
+A specific CPU can be specified via the '-cpu' parameter but please make
+sure the specified CPU supports 64-bit like '-cpu core2duo'. Conversely
+'-cpu pentium' won't work for obvious reasons that the processor only
+supports 32-bit.
+
+Note 64-bit support is very preliminary at this point. Lots of features
+are missing in the 64-bit world. One notable feature is the VGA console
+support which is currently missing, so that you must specify '-nographic'
+to get 64-bit U-Boot up and running.
diff --git a/doc/board/index.rst b/doc/board/index.rst
index eb21a67..6d2356f 100644
--- a/doc/board/index.rst
+++ b/doc/board/index.rst
@@ -7,5 +7,6 @@
:maxdepth: 2
coreboot/index
+ emulation/index
google/index
intel/index