rockchip: add basic support for evb-rk3288 board
evb-3288 board RK3288-based development board with 2 USB ports, HDMI,
VGA, micro-SD card, audio, WiFi and Gigabit Ethernet. It also includes
on-board 8G eMMC and 2GB of SDRAM. Expansion connector provide access to
display pins, I2C, SPI, UART and GPIOs. This add some basic files
required to allow the board to output serial messaged and can run
command(mmc info etc).
evb-rk3288 also supports booting from eMMC or SD card, the default is eMMC.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index ca8712a..88741e5 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -31,6 +31,7 @@
rk3288-firefly.dtb \
rk3288-jerry.dtb \
rk3288-rock2-square.dtb \
+ rk3288-evb.dtb \
rk3036-sdk.dtb
dtb-$(CONFIG_ARCH_MESON) += \
meson-gxbb-odroidc2.dtb
diff --git a/arch/arm/dts/rk3288-evb.dts b/arch/arm/dts/rk3288-evb.dts
new file mode 100644
index 0000000..caf24ee
--- /dev/null
+++ b/arch/arm/dts/rk3288-evb.dts
@@ -0,0 +1,59 @@
+/*
+ * (C) Copyright 2016 Rockchip Electronics Co., Ltd
+ *
+ * SPDX-License-Identifier: GPL-2.0+ X11
+ */
+
+/dts-v1/;
+#include "rk3288-evb.dtsi"
+
+/ {
+ model = "Evb-RK3288";
+ compatible = "evb-rk3288,evb-rk3288", "rockchip,rk3288";
+
+ chosen {
+ stdout-path = &uart2;
+ };
+};
+
+&dmc {
+ rockchip,num-channels = <2>;
+ rockchip,pctl-timing = <0x215 0xc8 0x0 0x35 0x26 0x2 0x70 0x2000d
+ 0x6 0x0 0x8 0x4 0x17 0x24 0xd 0x6
+ 0x4 0x8 0x4 0x76 0x4 0x0 0x30 0x0
+ 0x1 0x2 0x2 0x4 0x0 0x0 0xc0 0x4
+ 0x8 0x1f4>;
+ rockchip,phy-timing = <0x48d7dd93 0x187008d8 0x121076
+ 0x0 0xc3 0x6 0x2>;
+ rockchip,sdram-channel = /bits/ 8 <0x2 0xa 0x3 0x2 0x2 0x0 0xe 0xe>;
+ rockchip,sdram-params = <0x20d266a4 0x5b6 2 533000000 6 9 0>;
+};
+
+&pinctrl {
+ u-boot,dm-pre-reloc;
+};
+
+&pwm1 {
+ status = "okay";
+};
+
+&uart2 {
+ u-boot,dm-pre-reloc;
+ reg-shift = <2>;
+};
+
+&sdmmc {
+ u-boot,dm-pre-reloc;
+};
+
+&emmc {
+ u-boot,dm-pre-reloc;
+};
+
+&gpio3 {
+ u-boot,dm-pre-reloc;
+};
+
+&gpio8 {
+ u-boot,dm-pre-reloc;
+};
diff --git a/arch/arm/dts/rk3288-evb.dtsi b/arch/arm/dts/rk3288-evb.dtsi
new file mode 100644
index 0000000..cb7d03e
--- /dev/null
+++ b/arch/arm/dts/rk3288-evb.dtsi
@@ -0,0 +1,379 @@
+/*
+ * (C) Copyright 2016 Rockchip Electronics Co., Ltd
+ *
+ * SPDX-License-Identifier: GPL-2.0+ X11
+ */
+
+#include "rk3288.dtsi"
+
+/ {
+ memory {
+ reg = <0 0x80000000>;
+ };
+
+ keys: gpio-keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ button@0 {
+ gpio-key,wakeup = <1>;
+ gpios = <&gpio0 5 GPIO_ACTIVE_LOW>;
+ label = "GPIO Power";
+ linux,code = <116>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwr_key>;
+ };
+ };
+
+ vcc_sys: vsys-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_sys";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vcc_flash: flash-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_flash";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vcc_io>;
+ };
+
+ vcc_5v: usb-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_5v";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ vin-supply = <&vcc_sys>;
+ };
+
+ vcc_host_5v: usb-host-regulator {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio0 14 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&host_vbus_drv>;
+ regulator-name = "vcc_host_5v";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ vin-supply = <&vcc_5v>;
+ };
+
+ vcc_otg_5v: usb-otg-regulator {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio0 12 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&otg_vbus_drv>;
+ regulator-name = "vcc_otg_5v";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ vin-supply = <&vcc_5v>;
+ };
+};
+
+&cpu0 {
+ cpu0-supply = <&vdd_cpu>;
+};
+
+&emmc {
+ broken-cd;
+ bus-width = <8>;
+ cap-mmc-highspeed;
+ disable-wp;
+ non-removable;
+ num-slots = <1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&emmc_clk>, <&emmc_cmd>, <&emmc_pwr>, <&emmc_bus8>;
+ vmmc-supply = <&vcc_io>;
+ vqmmc-supply = <&vcc_flash>;
+ status = "okay";
+};
+
+&hdmi {
+ ddc-i2c-bus = <&i2c5>;
+ status = "okay";
+};
+
+&i2c0 {
+ clock-frequency = <400000>;
+ status = "okay";
+
+ vdd_cpu: syr827@40 {
+ compatible = "silergy,syr827";
+ fcs,suspend-voltage-selector = <1>;
+ reg = <0x40>;
+ regulator-name = "vdd_cpu";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-always-on;
+ regulator-boot-on;
+ vin-supply = <&vcc_sys>;
+ };
+
+ vdd_gpu: syr828@41 {
+ compatible = "silergy,syr828";
+ fcs,suspend-voltage-selector = <1>;
+ reg = <0x41>;
+ regulator-name = "vdd_gpu";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-always-on;
+ vin-supply = <&vcc_sys>;
+ };
+
+ hym8563: hym8563@51 {
+ compatible = "haoyu,hym8563";
+ reg = <0x51>;
+ #clock-cells = <0>;
+ clock-frequency = <32768>;
+ clock-output-names = "xin32k";
+ interrupt-parent = <&gpio7>;
+ interrupts = <4 IRQ_TYPE_EDGE_FALLING>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&rtc_int>;
+ };
+
+ act8846: act8846@5a {
+ compatible = "active-semi,act8846";
+ reg = <0x5a>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwr_hold>;
+ system-power-controller;
+
+ regulators {
+ vcc_ddr: REG1 {
+ regulator-name = "vcc_ddr";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ };
+
+ vcc_io: REG2 {
+ regulator-name = "vcc_io";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ vdd_log: REG3 {
+ regulator-name = "vdd_log";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-always-on;
+ };
+
+ vcc_20: REG4 {
+ regulator-name = "vcc_20";
+ regulator-min-microvolt = <2000000>;
+ regulator-max-microvolt = <2000000>;
+ regulator-always-on;
+ };
+
+ vccio_sd: REG5 {
+ regulator-name = "vccio_sd";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ vdd10_lcd: REG6 {
+ regulator-name = "vdd10_lcd";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ };
+
+ vcca_codec: REG7 {
+ regulator-name = "vcca_codec";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ vcc_tp: REG8 {
+ regulator-name = "vcca_33";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ vccio_pmu: REG9 {
+ regulator-name = "vccio_pmu";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ vdd_10: REG10 {
+ regulator-name = "vdd_10";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ };
+
+ vcc_18: REG11 {
+ regulator-name = "vcc_18";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ vcc18_lcd: REG12 {
+ regulator-name = "vcc18_lcd";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+ };
+ };
+};
+
+&i2c1 {
+ status = "okay";
+};
+
+&i2c2 {
+ status = "okay";
+};
+
+&i2c4 {
+ status = "okay";
+};
+
+&i2c5 {
+ status = "okay";
+};
+
+&pinctrl {
+ pcfg_output_high: pcfg-output-high {
+ output-high;
+ };
+
+ pcfg_output_low: pcfg-output-low {
+ output-low;
+ };
+
+ act8846 {
+ pwr_hold: pwr-hold {
+ rockchip,pins = <0 9 RK_FUNC_GPIO &pcfg_output_high>;
+ };
+ };
+
+ hym8563 {
+ rtc_int: rtc-int {
+ rockchip,pins = <0 4 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ keys {
+ pwr_key: pwr-key {
+ rockchip,pins = <0 5 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ sdmmc {
+ sdmmc_pwr: sdmmc-pwr {
+ rockchip,pins = <7 11 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ usb_host {
+ host_vbus_drv: host-vbus-drv {
+ rockchip,pins = <0 14 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ usb_otg {
+ otg_vbus_drv: otg-vbus-drv {
+ rockchip,pins = <0 12 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+};
+
+&saradc {
+ vref-supply = <&vcc_18>;
+ status = "okay";
+};
+
+&sdio0 {
+ broken-cd;
+ bus-width = <4>;
+ disable-wp;
+ non-removable;
+ num-slots = <1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdio0_bus4>, <&sdio0_cmd>, <&sdio0_clk>;
+ vmmc-supply = <&vcc_18>;
+ status = "disabled";
+};
+
+&sdmmc {
+ bus-width = <4>;
+ cap-mmc-highspeed;
+ cap-sd-highspeed;
+ card-detect-delay = <200>;
+ disable-wp;
+ num-slots = <1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdmmc_clk>, <&sdmmc_cmd>, <&sdmmc_cd>, <&sdmmc_bus4>;
+ vmmc-supply = <&vccio_sd>;
+ status = "okay";
+};
+
+&spi0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi0_clk>, <&spi0_cs0>, <&spi0_tx>, <&spi0_rx>, <&spi0_cs1>;
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_xfer>, <&uart0_cts>, <&uart0_rts>;
+ status = "okay";
+};
+
+&uart1 {
+ status = "okay";
+};
+
+&uart2 {
+ status = "okay";
+};
+
+&uart3 {
+ status = "okay";
+};
+
+&usb_host1 {
+ status = "okay";
+};
+
+&usb_otg {
+ status = "okay";
+};
+
+&vopb {
+ status = "okay";
+};
+
+&vopb_mmu {
+ status = "okay";
+};
+
+&vopl {
+ status = "okay";
+};
+
+&vopl_mmu {
+ status = "okay";
+};
+
+&wdt {
+ status = "okay";
+};
diff --git a/arch/arm/mach-rockchip/rk3288-board-spl.c b/arch/arm/mach-rockchip/rk3288-board-spl.c
index 08152aa..d82115f 100644
--- a/arch/arm/mach-rockchip/rk3288-board-spl.c
+++ b/arch/arm/mach-rockchip/rk3288-board-spl.c
@@ -251,7 +251,8 @@
}
#ifdef CONFIG_SPL_MMC_SUPPORT
if (!IS_ENABLED(CONFIG_TARGET_ROCK2) &&
- !IS_ENABLED(CONFIG_TARGET_FIREFLY_RK3288)) {
+ !IS_ENABLED(CONFIG_TARGET_FIREFLY_RK3288) &&
+ !IS_ENABLED(CONFIG_TARGET_EVB_RK3288)) {
ret = pinctrl_request_noflags(pinctrl, PERIPH_ID_SDCARD);
if (ret) {
debug("%s: Failed to set up SD card\n", __func__);
diff --git a/arch/arm/mach-rockchip/rk3288/Kconfig b/arch/arm/mach-rockchip/rk3288/Kconfig
index 7215624..031dbfc 100644
--- a/arch/arm/mach-rockchip/rk3288/Kconfig
+++ b/arch/arm/mach-rockchip/rk3288/Kconfig
@@ -8,6 +8,14 @@
also includes on-board eMMC and 1GB of SDRAM. Expansion connectors
provide access to display pins, I2C, SPI, UART and GPIOs.
+config TARGET_EVB_RK3288
+ bool "Evb-RK3288"
+ help
+ EVB-RK3288 is a RK3288-based development board with 2 USB ports,
+ HDMI, VGA, micro-SD card, audio, WiFi and Gigabit Ethernet, It
+ also includes on-board eMMC and 2GB of SDRAM. Expansion connectors
+ provide access to display pins, I2C, SPI, UART and GPIOs.
+
config TARGET_CHROMEBOOK_JERRY
bool "Google/Rockchip Veyron-Jerry Chromebook"
help
@@ -45,4 +53,6 @@
source "board/radxa/rock2/Kconfig"
+source "board/evb-rk3288/evb-rk3288/Kconfig"
+
endif
diff --git a/board/evb-rk3288/evb-rk3288/Kconfig b/board/evb-rk3288/evb-rk3288/Kconfig
new file mode 100644
index 0000000..b201acb
--- /dev/null
+++ b/board/evb-rk3288/evb-rk3288/Kconfig
@@ -0,0 +1,15 @@
+if TARGET_EVB_RK3288
+
+config SYS_BOARD
+ default "evb-rk3288"
+
+config SYS_VENDOR
+ default "evb-rk3288"
+
+config SYS_CONFIG_NAME
+ default "evb-rk3288"
+
+config BOARD_SPECIFIC_OPTIONS # dummy
+ def_bool y
+
+endif
diff --git a/board/evb-rk3288/evb-rk3288/MAINTAINERS b/board/evb-rk3288/evb-rk3288/MAINTAINERS
new file mode 100644
index 0000000..222c254
--- /dev/null
+++ b/board/evb-rk3288/evb-rk3288/MAINTAINERS
@@ -0,0 +1,6 @@
+EVB-RK3288
+M: Lin Huang <hl@rock-chips.com>
+S: Maintained
+F: board/evb-rk3288/evb-rk3288
+F: include/configs/evb-rk3288.h
+F: configs/evb-rk3288_defconfig
diff --git a/board/evb-rk3288/evb-rk3288/Makefile b/board/evb-rk3288/evb-rk3288/Makefile
new file mode 100644
index 0000000..c11b657
--- /dev/null
+++ b/board/evb-rk3288/evb-rk3288/Makefile
@@ -0,0 +1,7 @@
+#
+# (C) Copyright 2016 Rockchip Electronics Co., Ltd
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+obj-y += evb-rk3288.o
diff --git a/board/evb-rk3288/evb-rk3288/evb-rk3288.c b/board/evb-rk3288/evb-rk3288/evb-rk3288.c
new file mode 100644
index 0000000..a82f0ae
--- /dev/null
+++ b/board/evb-rk3288/evb-rk3288/evb-rk3288.c
@@ -0,0 +1,15 @@
+/*
+ * (C) Copyright 2016 Rockchip Electronics Co., Ltd
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <spl.h>
+
+void board_boot_order(u32 *spl_boot_list)
+{
+ /* eMMC prior to sdcard. */
+ spl_boot_list[0] = BOOT_DEVICE_MMC2;
+ spl_boot_list[1] = BOOT_DEVICE_MMC1;
+}
diff --git a/configs/evb-rk3288_defconfig b/configs/evb-rk3288_defconfig
new file mode 100644
index 0000000..41cfedd
--- /dev/null
+++ b/configs/evb-rk3288_defconfig
@@ -0,0 +1,67 @@
+CONFIG_ARM=y
+CONFIG_ARCH_ROCKCHIP=y
+CONFIG_SYS_MALLOC_F_LEN=0x2000
+CONFIG_ROCKCHIP_RK3288=y
+CONFIG_TARGET_EVB_RK3288=y
+CONFIG_SPL_STACK_R_ADDR=0x80000
+CONFIG_DEFAULT_DEVICE_TREE="rk3288-evb"
+CONFIG_SPL_STACK_R=y
+CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x2000
+CONFIG_HUSH_PARSER=y
+CONFIG_CMD_BOOTZ=y
+# CONFIG_CMD_IMLS is not set
+CONFIG_CMD_MMC=y
+CONFIG_CMD_SF=y
+CONFIG_CMD_SPI=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_GPIO=y
+# CONFIG_CMD_SETEXPR is not set
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_MII=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_TIME=y
+CONFIG_CMD_PMIC=y
+CONFIG_CMD_REGULATOR=y
+CONFIG_CMD_EXT2=y
+CONFIG_CMD_EXT4=y
+CONFIG_CMD_FAT=y
+CONFIG_CMD_FS_GENERIC=y
+CONFIG_SPL_OF_CONTROL=y
+CONFIG_OF_SPL_REMOVE_PROPS="pinctrl-0 pinctrl-names clock-names interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents"
+CONFIG_REGMAP=y
+CONFIG_SPL_REGMAP=y
+CONFIG_SYSCON=y
+CONFIG_SPL_SYSCON=y
+CONFIG_CLK=y
+CONFIG_SPL_CLK=y
+CONFIG_ROCKCHIP_GPIO=y
+CONFIG_SYS_I2C_ROCKCHIP=y
+CONFIG_LED=y
+CONFIG_LED_GPIO=y
+CONFIG_SYSRESET=y
+CONFIG_DM_MMC=y
+CONFIG_ROCKCHIP_DWMMC=y
+CONFIG_PINCTRL=y
+# CONFIG_PINCTRL_FULL is not set
+CONFIG_SPL_PINCTRL=y
+# CONFIG_SPL_PINCTRL_FULL is not set
+CONFIG_ROCKCHIP_PINCTRL=y
+CONFIG_DM_PMIC=y
+CONFIG_PMIC_ACT8846=y
+CONFIG_DM_REGULATOR=y
+CONFIG_REGULATOR_ACT8846=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_PWM=y
+CONFIG_PWM_ROCKCHIP=y
+CONFIG_RAM=y
+CONFIG_SPL_RAM=y
+CONFIG_DEBUG_UART=y
+CONFIG_DEBUG_UART_BASE=0xff690000
+CONFIG_DEBUG_UART_CLOCK=24000000
+CONFIG_DEBUG_UART_SHIFT=2
+CONFIG_SYS_NS16550=y
+CONFIG_USE_PRIVATE_LIBGCC=y
+CONFIG_USE_TINY_PRINTF=y
+CONFIG_CMD_DHRYSTONE=y
+CONFIG_ERRNO_STR=y
diff --git a/doc/README.rockchip b/doc/README.rockchip
index 182e3ae..3fc2582 100644
--- a/doc/README.rockchip
+++ b/doc/README.rockchip
@@ -36,11 +36,12 @@
Building
========
-At present three RK3288 boards are supported:
+At present four RK3288 boards are supported:
- Firefly RK3288 - use firefly-rk3288 configuration
- Radxa Rock 2 - use rock2 configuration
- Hisense Chromebook - use chromebook_jerry configuration
+ - EVB RK3288 - use evb-rk3288 configuration
Two RK3036 board are supported:
diff --git a/include/configs/evb-rk3288.h b/include/configs/evb-rk3288.h
new file mode 100644
index 0000000..342557f
--- /dev/null
+++ b/include/configs/evb-rk3288.h
@@ -0,0 +1,26 @@
+/*
+ * (C) Copyright 2016 Rockchip Electronics Co., Ltd
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#define ROCKCHIP_DEVICE_SETTINGS
+#include <configs/rk3288_common.h>
+
+#define CONFIG_SPL_MMC_SUPPORT
+
+#define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_SYS_MMC_ENV_DEV 1
+/* SPL @ 32k for ~36k
+ * ENV @ 96k
+ * u-boot @ 128K
+ */
+#define CONFIG_ENV_OFFSET (96 * 1024)
+
+#define CONFIG_SYS_WHITE_ON_BLACK
+#define CONFIG_CONSOLE_SCROLL_LINES 10
+
+#endif