ColdFire: Update for M54451EVB
Update serial boot DRAM's Internal RAM, vector table and DRAM in
start.S, serial flash's read status command over SPI and NOR
flash.
Signed-off-by: TsiChung Liew <tsicliew@gmail.com>
diff --git a/include/configs/M54451EVB.h b/include/configs/M54451EVB.h
index 45f7016..cc57da8 100644
--- a/include/configs/M54451EVB.h
+++ b/include/configs/M54451EVB.h
@@ -70,6 +70,7 @@
#define CONFIG_CMD_MISC
#define CONFIG_CMD_MII
#define CONFIG_CMD_NET
+#define CONFIG_CMD_NFS
#define CONFIG_CMD_PING
#define CONFIG_CMD_REGINFO
#define CONFIG_CMD_SPI
@@ -163,7 +164,7 @@
#define CONFIG_SYS_I2C_SPEED 80000 /* I2C speed and slave address */
#define CONFIG_SYS_I2C_SLAVE 0x7F
#define CONFIG_SYS_I2C_OFFSET 0x58000
-#define CONFIG_SYS_IMMR CONFIG_SYS_MBAR
+#define CONFIG_SYS_IMMR CONFIG_SYS_MBAR
/* DSPI and Serial Flash */
#define CONFIG_CF_DSPI
@@ -175,7 +176,7 @@
# define CONFIG_SPI_FLASH
# define CONFIG_SPI_FLASH_STMICRO
-# define CONFIG_SYS_DSPI_DCTAR0 (DSPI_DCTAR_TRSZ(7) | \
+# define CONFIG_SYS_DSPI_DCTAR0 (DSPI_DCTAR_TRSZ(7) | \
DSPI_DCTAR_CPOL | \
DSPI_DCTAR_CPHA | \
DSPI_DCTAR_PCSSCK_1CLK | \
@@ -191,7 +192,7 @@
/* Input, PCI, Flexbus, and VCO */
#define CONFIG_EXTRA_CLOCK
-#define CONFIG_PRAM 2048 /* 2048 KB */
+#define CONFIG_PRAM 2048 /* 2048 KB */
#define CONFIG_SYS_PROMPT "-> "
#define CONFIG_SYS_LONGHELP /* undef to save memory */
@@ -209,7 +210,7 @@
#define CONFIG_SYS_HZ 1000
-#define CONFIG_SYS_MBAR 0xFC000000
+#define CONFIG_SYS_MBAR 0xFC000000
/*
* Low Level Configuration Settings
@@ -265,7 +266,7 @@
/* Configuration for environment
* Environment is embedded in u-boot in the second sector of the flash
*/
-#if defined(CONFIG_CF_SBF)
+#if defined(CONFIG_SYS_STMICRO_BOOT)
# define CONFIG_ENV_IS_IN_SPI_FLASH 1
# define CONFIG_ENV_SPI_CS 1
# define CONFIG_ENV_OFFSET 0x20000
@@ -273,8 +274,9 @@
# define CONFIG_ENV_SECT_SIZE 0x10000
#else
# define CONFIG_ENV_IS_IN_FLASH 1
-# define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x4000)
-# define CONFIG_ENV_SECT_SIZE 0x2000
+# define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x8000)
+# define CONFIG_ENV_SIZE 0x2000
+# define CONFIG_ENV_SECT_SIZE 0x8000
#endif
#undef CONFIG_ENV_OVERWRITE
#undef CONFIG_ENV_IS_EMBEDDED
@@ -286,8 +288,7 @@
# define CONFIG_SYS_FLASH_BASE CONFIG_SYS_SER_FLASH_BASE
# define CONFIG_SYS_FLASH0_BASE CONFIG_SYS_SER_FLASH_BASE
# define CONFIG_SYS_FLASH1_BASE CONFIG_SYS_CS0_BASE
-#endif
-#ifdef CONFIG_SYS_SPANSION_BOOT
+#else
# define CONFIG_SYS_FLASH_BASE CONFIG_SYS_CS0_BASE
# define CONFIG_SYS_FLASH0_BASE CONFIG_SYS_CS0_BASE
# define CONFIG_SYS_FLASH1_BASE CONFIG_SYS_SER_FLASH_BASE
@@ -297,6 +298,7 @@
#ifdef CONFIG_SYS_FLASH_CFI
# define CONFIG_FLASH_CFI_DRIVER 1
+# define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1
# define CONFIG_SYS_FLASH_SIZE 0x1000000 /* Max size that the board might have */
# define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT
# define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
@@ -311,27 +313,20 @@
* This is setting for JFFS2 support in u-boot.
* NOTE: Enable CONFIG_CMD_JFFS2 for JFFS2 support.
*/
-#ifdef CONFIG_SYS_SPANSION_BOOT
-# define CONFIG_JFFS2_DEV "nor0"
-# define CONFIG_JFFS2_PART_SIZE 0x01000000
-# define CONFIG_JFFS2_PART_OFFSET (CONFIG_SYS_FLASH0_BASE + 0x500000)
-#endif
-#ifdef CONFIG_SYS_STMICRO_BOOT
+#ifdef CONFIG_CMD_JFFS2
# define CONFIG_JFFS2_DEV "nor0"
# define CONFIG_JFFS2_PART_SIZE 0x01000000
# define CONFIG_JFFS2_PART_OFFSET (CONFIG_SYS_FLASH0_BASE + 0x500000)
#endif
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
+/* Cache Configuration */
#define CONFIG_SYS_CACHELINE_SIZE 16
/*-----------------------------------------------------------------------
* Memory bank definitions
*/
/*
- * CS0 - NOR Flash 8MB
+ * CS0 - NOR Flash 16MB
* CS1 - Available
* CS2 - Available
* CS3 - Available
@@ -339,10 +334,10 @@
* CS5 - Available
*/
- /* SPANSION Flash */
+ /* Flash */
#define CONFIG_SYS_CS0_BASE 0x00000000
-#define CONFIG_SYS_CS0_MASK 0x007F0001
-#define CONFIG_SYS_CS0_CTRL 0x00001180
+#define CONFIG_SYS_CS0_MASK 0x00FF0001
+#define CONFIG_SYS_CS0_CTRL 0x00004D80
#define CONFIG_SYS_SPANSION_BASE CONFIG_SYS_CS0_BASE