imx: mx7dsabresd: support nand
Add pinmux settings.
Add related macro definitions.
Nand pin conflicts with emmc, so if want to enable nand, need to do
hardware rework. After hardware rework, define CONFIG_NAND_MXS in
board header file.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
diff --git a/board/freescale/mx7dsabresd/mx7dsabresd.c b/board/freescale/mx7dsabresd/mx7dsabresd.c
index f8ae973..bbcc5bb 100644
--- a/board/freescale/mx7dsabresd/mx7dsabresd.c
+++ b/board/freescale/mx7dsabresd/mx7dsabresd.c
@@ -47,6 +47,9 @@
#define QSPI_PAD_CTRL \
(PAD_CTL_DSE_3P3V_49OHM | PAD_CTL_PUE | PAD_CTL_PUS_PU47KOHM)
+#define NAND_PAD_CTRL (PAD_CTL_DSE_3P3V_49OHM | PAD_CTL_SRE_SLOW | PAD_CTL_HYS)
+
+#define NAND_PAD_READY0_CTRL (PAD_CTL_DSE_3P3V_49OHM | PAD_CTL_PUS_PU5KOHM)
#ifdef CONFIG_SYS_I2C_MXC
#define PC MUX_PAD_CTRL(I2C_PAD_CTRL)
/* I2C1 for PMIC */
@@ -196,6 +199,38 @@
gpio_direction_output(IOX_STCP, 1);
};
+#ifdef CONFIG_NAND_MXS
+static iomux_v3_cfg_t const gpmi_pads[] = {
+ MX7D_PAD_SD3_DATA0__NAND_DATA00 | MUX_PAD_CTRL(NAND_PAD_CTRL),
+ MX7D_PAD_SD3_DATA1__NAND_DATA01 | MUX_PAD_CTRL(NAND_PAD_CTRL),
+ MX7D_PAD_SD3_DATA2__NAND_DATA02 | MUX_PAD_CTRL(NAND_PAD_CTRL),
+ MX7D_PAD_SD3_DATA3__NAND_DATA03 | MUX_PAD_CTRL(NAND_PAD_CTRL),
+ MX7D_PAD_SD3_DATA4__NAND_DATA04 | MUX_PAD_CTRL(NAND_PAD_CTRL),
+ MX7D_PAD_SD3_DATA5__NAND_DATA05 | MUX_PAD_CTRL(NAND_PAD_CTRL),
+ MX7D_PAD_SD3_DATA6__NAND_DATA06 | MUX_PAD_CTRL(NAND_PAD_CTRL),
+ MX7D_PAD_SD3_DATA7__NAND_DATA07 | MUX_PAD_CTRL(NAND_PAD_CTRL),
+ MX7D_PAD_SD3_CLK__NAND_CLE | MUX_PAD_CTRL(NAND_PAD_CTRL),
+ MX7D_PAD_SD3_CMD__NAND_ALE | MUX_PAD_CTRL(NAND_PAD_CTRL),
+ MX7D_PAD_SD3_STROBE__NAND_RE_B | MUX_PAD_CTRL(NAND_PAD_CTRL),
+ MX7D_PAD_SD3_RESET_B__NAND_WE_B | MUX_PAD_CTRL(NAND_PAD_CTRL),
+ MX7D_PAD_SAI1_MCLK__NAND_WP_B | MUX_PAD_CTRL(NAND_PAD_CTRL),
+ MX7D_PAD_SAI1_RX_BCLK__NAND_CE3_B | MUX_PAD_CTRL(NAND_PAD_CTRL),
+ MX7D_PAD_SAI1_RX_SYNC__NAND_CE2_B | MUX_PAD_CTRL(NAND_PAD_CTRL),
+ MX7D_PAD_SAI1_RX_DATA__NAND_CE1_B | MUX_PAD_CTRL(NAND_PAD_CTRL),
+ MX7D_PAD_SAI1_TX_BCLK__NAND_CE0_B | MUX_PAD_CTRL(NAND_PAD_CTRL),
+ MX7D_PAD_SAI1_TX_SYNC__NAND_DQS | MUX_PAD_CTRL(NAND_PAD_CTRL),
+ MX7D_PAD_SAI1_TX_DATA__NAND_READY_B | MUX_PAD_CTRL(NAND_PAD_READY0_CTRL),
+};
+
+static void setup_gpmi_nand(void)
+{
+ imx_iomux_v3_setup_multiple_pads(gpmi_pads, ARRAY_SIZE(gpmi_pads));
+
+ /* NAND_USDHC_BUS_CLK is set in rom */
+ set_clk_nand();
+}
+#endif
+
#ifdef CONFIG_VIDEO_MXS
static iomux_v3_cfg_t const lcd_pads[] = {
MX7D_PAD_LCD_CLK__LCD_CLK | MUX_PAD_CTRL(LCD_PAD_CTRL),
@@ -503,6 +538,10 @@
setup_fec();
#endif
+#ifdef CONFIG_NAND_MXS
+ setup_gpmi_nand();
+#endif
+
#ifdef CONFIG_VIDEO_MXS
setup_lcd();
#endif