Tegra114: MMC: Add SD bus power-rail init routine
T114 requires SD bus power-rail bringup for the SDIO card on SDMMC3.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
diff --git a/board/nvidia/dalmore/dalmore.c b/board/nvidia/dalmore/dalmore.c
index 7449b5b..2c23a29 100644
--- a/board/nvidia/dalmore/dalmore.c
+++ b/board/nvidia/dalmore/dalmore.c
@@ -18,6 +18,10 @@
#include <asm/arch/pinmux.h>
#include <asm/arch/gp_padctrl.h>
#include "pinmux-config-dalmore.h"
+#include <i2c.h>
+
+#define BAT_I2C_ADDRESS 0x48 /* TPS65090 charger */
+#define PMU_I2C_ADDRESS 0x58 /* TPS65913 PMU */
/*
* Routine: pinmux_init
@@ -37,3 +41,61 @@
/* Initialize any non-default pad configs (APB_MISC_GP regs) */
padgrp_config_table(dalmore_padctrl, ARRAY_SIZE(dalmore_padctrl));
}
+
+#if defined(CONFIG_TEGRA_MMC)
+/*
+ * Do I2C/PMU writes to bring up SD card bus power
+ *
+ */
+void board_sdmmc_voltage_init(void)
+{
+ uchar reg, data_buffer[1];
+ int ret;
+
+ ret = i2c_set_bus_num(0);/* PMU is on bus 0 */
+ if (ret)
+ printf("%s: i2c_set_bus_num returned %d\n", __func__, ret);
+
+ /* TPS65913: LDO9_VOLTAGE = 3.3V */
+ data_buffer[0] = 0x31;
+ reg = 0x61;
+
+ ret = i2c_write(PMU_I2C_ADDRESS, reg, 1, data_buffer, 1);
+ if (ret)
+ printf("%s: PMU i2c_write %02X<-%02X returned %d\n",
+ __func__, reg, data_buffer[0], ret);
+
+ /* TPS65913: LDO9_CTRL = Active */
+ data_buffer[0] = 0x01;
+ reg = 0x60;
+
+ ret = i2c_write(PMU_I2C_ADDRESS, reg, 1, data_buffer, 1);
+ if (ret)
+ printf("%s: PMU i2c_write %02X<-%02X returned %d\n",
+ __func__, reg, data_buffer[0], ret);
+
+ /* TPS65090: FET6_CTRL = enable output auto discharge, enable FET6 */
+ data_buffer[0] = 0x03;
+ reg = 0x14;
+
+ ret = i2c_write(BAT_I2C_ADDRESS, reg, 1, data_buffer, 1);
+ if (ret)
+ printf("%s: BAT i2c_write %02X<-%02X returned %d\n",
+ __func__, reg, data_buffer[0], ret);
+}
+
+/*
+ * Routine: pin_mux_mmc
+ * Description: setup the MMC muxes, power rails, etc.
+ */
+void pin_mux_mmc(void)
+{
+ /*
+ * NOTE: We don't do mmc-specific pin muxes here.
+ * They were done globally in pinmux_init().
+ */
+
+ /* Bring up the SDIO3 power rail */
+ board_sdmmc_voltage_init();
+}
+#endif /* MMC */