rename CFG_ macros to CONFIG_SYS
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
diff --git a/include/configs/RPXClassic.h b/include/configs/RPXClassic.h
index 4fa21b8..162ef09 100644
--- a/include/configs/RPXClassic.h
+++ b/include/configs/RPXClassic.h
@@ -50,7 +50,7 @@
/* Define CONFIG_FEC_ENET to use Fast ethernet instead of ethernet on SCC1 */
#define CONFIG_FEC_ENET
#ifdef CONFIG_FEC_ENET
-#define CFG_DISCOVER_PHY 1
+#define CONFIG_SYS_DISCOVER_PHY 1
#define CONFIG_MII 1
#endif /* CONFIG_FEC_ENET */
@@ -84,7 +84,7 @@
"bootm"
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#undef CFG_LOADS_BAUD_CHANGE /* don't allow baudrate change */
+#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */
#undef CONFIG_WATCHDOG /* watchdog disabled */
@@ -112,26 +112,26 @@
/*
* Miscellaneous configurable options
*/
-#define CFG_RESET_ADDRESS 0x80000000
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+#define CONFIG_SYS_RESET_ADDRESS 0x80000000
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_MEMTEST_START 0x0040000 /* memtest works on */
-#define CFG_MEMTEST_END 0x00C0000 /* 4 ... 12 MB in DRAM */
+#define CONFIG_SYS_MEMTEST_START 0x0040000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0x00C0000 /* 4 ... 12 MB in DRAM */
-#define CFG_LOAD_ADDR 0x100000 /* default load address */
+#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */
-#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
/*
* Low Level Configuration Settings
@@ -141,15 +141,15 @@
/*-----------------------------------------------------------------------
* Internal Memory Mapped Register
*/
-#define CFG_IMMR 0xFA200000
+#define CONFIG_SYS_IMMR 0xFA200000
/*-----------------------------------------------------------------------------
* I2C Configuration
*-----------------------------------------------------------------------------
*/
#define CONFIG_I2C 1
-#define CFG_I2C_SPEED 50000
-#define CFG_I2C_SLAVE 0x34
+#define CONFIG_SYS_I2C_SPEED 50000
+#define CONFIG_SYS_I2C_SLAVE 0x34
/* enable I2C and select the hardware/software driver */
@@ -169,54 +169,54 @@
#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */
-# define CFG_I2C_SPEED 50000
-# define CFG_I2C_SLAVE 0x34
-# define CFG_I2C_EEPROM_ADDR 0x50 /* EEPROM X24C16 */
-# define CFG_I2C_EEPROM_ADDR_LEN 1 /* bytes of address */
+# define CONFIG_SYS_I2C_SPEED 50000
+# define CONFIG_SYS_I2C_SLAVE 0x34
+# define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM X24C16 */
+# define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* bytes of address */
/* mask of address bits that overflow into the "EEPROM chip address" */
-#define CFG_I2C_EEPROM_ADDR_OVERFLOW 0x07
+#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x07
/*-----------------------------------------------------------------------
* Definitions for initial stack pointer and data area (in DPRAM)
*/
-#define CFG_INIT_RAM_ADDR CFG_IMMR
-#define CFG_INIT_RAM_END 0x3000 /* End of used area in DPRAM */
-#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */
-#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
+#define CONFIG_SYS_INIT_RAM_END 0x3000 /* End of used area in DPRAM */
+#define CONFIG_SYS_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
/*-----------------------------------------------------------------------
* Start addresses for the final memory configuration
* (Set up by the startup code)
- * Please note that CFG_SDRAM_BASE _must_ start at 0
+ * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
*/
-#define CFG_SDRAM_BASE 0x00000000
-#define CFG_FLASH_BASE 0xFF000000
+#define CONFIG_SYS_SDRAM_BASE 0x00000000
+#define CONFIG_SYS_FLASH_BASE 0xFF000000
#if defined(DEBUG) || defined (CONFIG_VIDEO_SED13806) || defined(CONFIG_CMD_IDE)
-#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
+#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
#else
-#define CFG_MONITOR_LEN (128 << 10) /* Reserve 128 kB for Monitor */
+#define CONFIG_SYS_MONITOR_LEN (128 << 10) /* Reserve 128 kB for Monitor */
#endif
-#define CFG_MONITOR_BASE 0xFF000000
-/*%%% #define CFG_MONITOR_BASE CFG_FLASH_BASE */
-#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
+#define CONFIG_SYS_MONITOR_BASE 0xFF000000
+/*%%% #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE */
+#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
/*-----------------------------------------------------------------------
* FLASH organization
*/
-#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#define CFG_MAX_FLASH_SECT 71 /* max number of sectors on one chip */
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 71 /* max number of sectors on one chip */
-#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
-#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
+#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
#if 0
#define CONFIG_ENV_IS_IN_FLASH 1
@@ -232,9 +232,9 @@
/*-----------------------------------------------------------------------
* Cache Configuration
*/
-#define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
+#define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
#if defined(CONFIG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */
+#define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */
#endif
/*-----------------------------------------------------------------------
@@ -243,7 +243,7 @@
*-----------------------------------------------------------------------
* Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
*/
-#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
+#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
SYPCR_SWP)
/*-----------------------------------------------------------------------
@@ -251,28 +251,28 @@
*-----------------------------------------------------------------------
* PCMCIA config., multi-function pin tri-state
*/
-#define CFG_SIUMCR (SIUMCR_MLRC10)
+#define CONFIG_SYS_SIUMCR (SIUMCR_MLRC10)
/*-----------------------------------------------------------------------
* TBSCR - Time Base Status and Control 11-26
*-----------------------------------------------------------------------
* Clear Reference Interrupt Status, Timebase freezing enabled
*/
-#define CFG_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF | TBSCR_TBE)
+#define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF | TBSCR_TBE)
/*-----------------------------------------------------------------------
* RTCSC - Real-Time Clock Status and Control Register 11-27
*-----------------------------------------------------------------------
*/
-/*%%%#define CFG_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE) */
-#define CFG_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTE)
+/*%%%#define CONFIG_SYS_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE) */
+#define CONFIG_SYS_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTE)
/*-----------------------------------------------------------------------
* PISCR - Periodic Interrupt Status and Control 11-31
*-----------------------------------------------------------------------
* Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
*/
-#define CFG_PISCR (PISCR_PS | PISCR_PITF | PISCR_PTE)
+#define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF | PISCR_PTE)
/*-----------------------------------------------------------------------
* PLPRCR - PLL, Low-Power, and Reset Control Register 15-30
@@ -283,7 +283,7 @@
* If this is a 80 MHz CPU, set PLL multiplication factor to 5 (5*16=80)!
*/
/* up to 50 MHz we use a 1:1 clock */
-#define CFG_PLPRCR ( (4 << PLPRCR_MF_SHIFT) | PLPRCR_TEXPS | PLPRCR_SPLSS | PLPRCR_TMIST)
+#define CONFIG_SYS_PLPRCR ( (4 << PLPRCR_MF_SHIFT) | PLPRCR_TEXPS | PLPRCR_SPLSS | PLPRCR_TMIST)
/*-----------------------------------------------------------------------
* SCCR - System Clock and reset Control Register 15-27
@@ -293,21 +293,21 @@
*/
#define SCCR_MASK SCCR_EBDF00
/* up to 50 MHz we use a 1:1 clock */
-#define CFG_SCCR (SCCR_COM00 | SCCR_TBS)
+#define CONFIG_SYS_SCCR (SCCR_COM00 | SCCR_TBS)
/*-----------------------------------------------------------------------
* PCMCIA stuff
*-----------------------------------------------------------------------
*
*/
-#define CFG_PCMCIA_MEM_ADDR (0xE0000000)
-#define CFG_PCMCIA_MEM_SIZE ( 64 << 20 )
-#define CFG_PCMCIA_DMA_ADDR (0xE4000000)
-#define CFG_PCMCIA_DMA_SIZE ( 64 << 20 )
-#define CFG_PCMCIA_ATTRB_ADDR (0xE8000000)
-#define CFG_PCMCIA_ATTRB_SIZE ( 64 << 20 )
-#define CFG_PCMCIA_IO_ADDR (0xEC000000)
-#define CFG_PCMCIA_IO_SIZE ( 64 << 20 )
+#define CONFIG_SYS_PCMCIA_MEM_ADDR (0xE0000000)
+#define CONFIG_SYS_PCMCIA_MEM_SIZE ( 64 << 20 )
+#define CONFIG_SYS_PCMCIA_DMA_ADDR (0xE4000000)
+#define CONFIG_SYS_PCMCIA_DMA_SIZE ( 64 << 20 )
+#define CONFIG_SYS_PCMCIA_ATTRB_ADDR (0xE8000000)
+#define CONFIG_SYS_PCMCIA_ATTRB_SIZE ( 64 << 20 )
+#define CONFIG_SYS_PCMCIA_IO_ADDR (0xEC000000)
+#define CONFIG_SYS_PCMCIA_IO_SIZE ( 64 << 20 )
/*-----------------------------------------------------------------------
* IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
@@ -320,29 +320,29 @@
#undef CONFIG_IDE_LED /* LED for ide not supported */
#undef CONFIG_IDE_RESET /* reset for ide not supported */
-#define CFG_IDE_MAXBUS 1 /* max. 1 IDE bus */
-#define CFG_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */
+#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */
+#define CONFIG_SYS_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */
-#define CFG_ATA_IDE0_OFFSET 0x0000
+#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
-#define CFG_ATA_BASE_ADDR CFG_PCMCIA_MEM_ADDR
+#define CONFIG_SYS_ATA_BASE_ADDR CONFIG_SYS_PCMCIA_MEM_ADDR
/* Offset for data I/O */
-#define CFG_ATA_DATA_OFFSET (CFG_PCMCIA_MEM_SIZE + 0x320)
+#define CONFIG_SYS_ATA_DATA_OFFSET (CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
/* Offset for normal register accesses */
-#define CFG_ATA_REG_OFFSET (2 * CFG_PCMCIA_MEM_SIZE + 0x320)
+#define CONFIG_SYS_ATA_REG_OFFSET (2 * CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
/* Offset for alternate registers */
-#define CFG_ATA_ALT_OFFSET 0x0100
+#define CONFIG_SYS_ATA_ALT_OFFSET 0x0100
/*-----------------------------------------------------------------------
*
*-----------------------------------------------------------------------
*
*/
-/* #define CFG_DER 0x2002000F */
-#define CFG_DER 0
+/* #define CONFIG_SYS_DER 0x2002000F */
+#define CONFIG_SYS_DER 0
/*
* Init Memory Controller:
@@ -351,13 +351,13 @@
*/
#define FLASH_BASE_PRELIM 0xFE000000 /* FLASH base */
-#define CFG_PRELIM_OR_AM 0xFE000000 /* OR addr mask */
+#define CONFIG_SYS_PRELIM_OR_AM 0xFE000000 /* OR addr mask */
/* FLASH timing: ACS = 0, TRLX = 0, CSNT = 0, SCY = 4, ETHR = 0, BIH = 1 */
-#define CFG_OR_TIMING_FLASH (OR_SCY_4_CLK | OR_BI)
+#define CONFIG_SYS_OR_TIMING_FLASH (OR_SCY_4_CLK | OR_BI)
-#define CFG_OR0_PRELIM (CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH)
-#define CFG_BR0_PRELIM ((FLASH_BASE_PRELIM & BR_BA_MSK) | BR_V)
+#define CONFIG_SYS_OR0_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
+#define CONFIG_SYS_BR0_PRELIM ((FLASH_BASE_PRELIM & BR_BA_MSK) | BR_V)
/*
* BR1 and OR1 (SDRAM)
@@ -367,16 +367,16 @@
#define SDRAM_MAX_SIZE 0x01000000 /* max 16 MB */
/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care) */
-#define CFG_OR_TIMING_SDRAM 0x00000E00
+#define CONFIG_SYS_OR_TIMING_SDRAM 0x00000E00
-#define CFG_OR1_PRELIM (CFG_PRELIM_OR_AM | CFG_OR_TIMING_SDRAM )
-#define CFG_BR1_PRELIM ((SDRAM_BASE_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
+#define CONFIG_SYS_OR1_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_SDRAM )
+#define CONFIG_SYS_BR1_PRELIM ((SDRAM_BASE_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
/* RPXLITE mem setting */
-#define CFG_BR3_PRELIM 0xFA400001 /* BCSR */
-#define CFG_OR3_PRELIM 0xff7f8970
-#define CFG_BR4_PRELIM 0xFA000401 /* NVRAM&SRAM */
-#define CFG_OR4_PRELIM 0xFFF80970
+#define CONFIG_SYS_BR3_PRELIM 0xFA400001 /* BCSR */
+#define CONFIG_SYS_OR3_PRELIM 0xff7f8970
+#define CONFIG_SYS_BR4_PRELIM 0xFA000401 /* NVRAM&SRAM */
+#define CONFIG_SYS_OR4_PRELIM 0xFFF80970
/* ECCX CS settings */
#define SED13806_OR 0xFFC00108 /* - 4 Mo
@@ -425,19 +425,19 @@
*/
/* periodic timer for refresh */
-#define CFG_MAMR_PTA 58
+#define CONFIG_SYS_MAMR_PTA 58
/*
* Refresh clock Prescalar
*/
-#define CFG_MPTPR MPTPR_PTP_DIV8
+#define CONFIG_SYS_MPTPR MPTPR_PTP_DIV8
/*
* MAMR settings for SDRAM
*/
/* 10 column SDRAM */
-#define CFG_MAMR_10COL ((CFG_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
+#define CONFIG_SYS_MAMR_10COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
MAMR_AMA_TYPE_2 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A12 | \
MAMR_GPL_A4DIS | MAMR_RLFA_4X | MAMR_WLFA_3X | MAMR_TLFA_16X)