mpc832x: add support for the mpc8321 based suvd3 board

- serial console on UART1
- Ethernet RMII over UCC4
- PHY SMSC LAN8700
- 64MB Flash
- 128 MB DDR2 RAM
- I2C
- bootcount

This board is similiar to the kmeter1 (8360) board,
so common config options are extracted into the
include/configs/km83xx-common.h file.

Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
diff --git a/include/configs/km83xx-common.h b/include/configs/km83xx-common.h
new file mode 100644
index 0000000..6b9cc30
--- /dev/null
+++ b/include/configs/km83xx-common.h
@@ -0,0 +1,324 @@
+/*
+ * (C) Copyright 2010
+ * Heiko Schocher, DENX Software Engineering, hs@denx.de.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ */
+
+#ifndef __CONFIG_KM83XX_H
+#define __CONFIG_KM83XX_H
+
+/* include common defines/options for all Keymile boards */
+#include "keymile-common.h"
+#include "km-powerpc.h"
+
+#define MTDIDS_DEFAULT		"nor0=boot"
+#define MTDPARTS_DEFAULT	"mtdparts="			\
+	"boot:"							\
+		"768k(u-boot),"					\
+		"128k(env),"					\
+		"128k(envred),"					\
+		"-(" CONFIG_KM_UBI_PARTITION_NAME ")"
+
+#define CONFIG_MISC_INIT_R
+/*
+ * System Clock Setup
+ */
+#define CONFIG_83XX_CLKIN		66000000
+#define CONFIG_SYS_CLK_FREQ		66000000
+#define CONFIG_83XX_PCICLK		66000000
+
+/*
+ * IMMR new address
+ */
+#define CONFIG_SYS_IMMR		0xE0000000
+
+/*
+ * Bus Arbitration Configuration Register (ACR)
+ */
+#define CONFIG_SYS_ACR_PIPE_DEP 3       /* pipeline depth 4 transactions */
+#define CONFIG_SYS_ACR_RPTCNT   3       /* 4 consecutive transactions */
+#define CONFIG_SYS_ACR_APARK    0       /* park bus to master (below) */
+#define CONFIG_SYS_ACR_PARKM    3       /* parking master = QuiccEngine */
+
+/*
+ * DDR Setup
+ */
+#define CONFIG_SYS_DDR_BASE		0x00000000 /* DDR is system memory */
+#define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_BASE
+#define CONFIG_SYS_DDR_SDRAM_BASE	CONFIG_SYS_DDR_BASE
+#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL	(DDR_SDRAM_CLK_CNTL_SS_EN | \
+					DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
+
+#define CFG_83XX_DDR_USES_CS0
+
+/*
+ * Manually set up DDR parameters
+ */
+#define CONFIG_DDR_II
+#define CONFIG_SYS_DDR_SIZE		2048 /* MB */
+
+/*
+ * The reserved memory
+ */
+#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE /* start of monitor */
+#define CONFIG_SYS_FLASH_BASE		0xF0000000
+
+#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
+#define CONFIG_SYS_RAMBOOT
+#endif
+
+/* Reserve 768 kB for Mon */
+#define CONFIG_SYS_MONITOR_LEN		(768 * 1024)
+
+/*
+ * Initial RAM Base Address Setup
+ */
+#define CONFIG_SYS_INIT_RAM_LOCK
+#define CONFIG_SYS_INIT_RAM_ADDR	0xE6000000 /* Initial RAM address */
+#define CONFIG_SYS_INIT_RAM_SIZE	0x1000 /* End of used area in RAM */
+#define CONFIG_SYS_GBL_DATA_SIZE	0x100 /* num bytes initial data */
+#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - \
+						GENERATED_GBL_DATA_SIZE)
+
+/*
+ * Init Local Bus Memory Controller:
+ *
+ * Bank Bus     Machine PortSz  Size  Device
+ * ---- ---     ------- ------  -----  ------
+ *  0   Local   GPCM    16 bit  256MB FLASH
+ *  1   Local   GPCM     8 bit  128MB GPIO/PIGGY
+ *
+ */
+/*
+ * FLASH on the Local Bus
+ */
+#define CONFIG_SYS_FLASH_CFI		/* use the Common Flash Interface */
+#define CONFIG_FLASH_CFI_DRIVER		/* use the CFI driver */
+#define CONFIG_SYS_FLASH_SIZE		256 /* max FLASH size is 256M */
+#define CONFIG_SYS_FLASH_PROTECTION
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
+
+#define CONFIG_SYS_LBLAWBAR0_PRELIM	CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_LBLAWAR0_PRELIM	0x8000001b /* 256MB window size */
+
+#define CONFIG_SYS_BR0_PRELIM	(CONFIG_SYS_FLASH_BASE | \
+				(2 << BR_PS_SHIFT) | /* 16 bit port size */ \
+				BR_V)
+
+#define CONFIG_SYS_OR0_PRELIM	(MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) | \
+				OR_GPCM_CSNT | OR_GPCM_ACS_DIV2 | \
+				OR_GPCM_SCY_5 | \
+				OR_GPCM_TRLX | OR_GPCM_EAD)
+
+#define CONFIG_SYS_MAX_FLASH_BANKS	1   /* max num of flash banks	*/
+#define CONFIG_SYS_MAX_FLASH_SECT	512 /* max num of sects on one chip */
+#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
+
+/*
+ * PRIO1/PIGGY on the local bus CS1
+ */
+#define CONFIG_SYS_LBLAWBAR1_PRELIM	CONFIG_SYS_PIGGY_BASE
+#define CONFIG_SYS_LBLAWAR1_PRELIM	0x8000001A /* 128MB window size */
+
+#define CONFIG_SYS_BR1_PRELIM	(CONFIG_SYS_PIGGY_BASE | \
+				(1 << BR_PS_SHIFT) | /* 8 bit port size */ \
+				BR_V)
+#define CONFIG_SYS_OR1_PRELIM		(MEG_TO_AM(CONFIG_SYS_PIGGY_SIZE) | \
+				OR_GPCM_CSNT | OR_GPCM_ACS_DIV2 | \
+				OR_GPCM_SCY_2 | \
+				OR_GPCM_TRLX | OR_GPCM_EAD)
+
+/*
+ * Serial Port
+ */
+#define CONFIG_CONS_INDEX	1
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE	1
+#define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)
+
+#define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_IMMR+0x4500)
+#define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_IMMR+0x4600)
+
+/* Pass open firmware flat tree */
+#define CONFIG_OF_LIBFDT
+#define CONFIG_OF_BOARD_SETUP
+#define CONFIG_OF_STDOUT_VIA_ALIAS
+
+#ifndef CONFIG_NET_MULTI
+#define CONFIG_NET_MULTI
+#endif
+/*
+ * QE UEC ethernet configuration
+ */
+#define CONFIG_UEC_ETH
+#define CONFIG_ETHPRIME		"UEC0"
+
+#define CONFIG_UEC_ETH1		/* GETH1 */
+#define UEC_VERBOSE_DEBUG	1
+
+#ifdef CONFIG_UEC_ETH1
+#define CONFIG_SYS_UEC1_UCC_NUM	3	/* UCC4 */
+#define CONFIG_SYS_UEC1_RX_CLK		QE_CLK_NONE /* not used in RMII Mode */
+#define CONFIG_SYS_UEC1_TX_CLK		QE_CLK17
+#define CONFIG_SYS_UEC1_ETH_TYPE	FAST_ETH
+#define CONFIG_SYS_UEC1_PHY_ADDR	0
+#define CONFIG_SYS_UEC1_INTERFACE_TYPE	PHY_INTERFACE_MODE_RMII
+#define CONFIG_SYS_UEC1_INTERFACE_SPEED	100
+#endif
+
+/*
+ * Environment
+ */
+
+#ifndef CONFIG_SYS_RAMBOOT
+#define CONFIG_ENV_IS_IN_FLASH
+#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE + \
+					CONFIG_SYS_MONITOR_LEN)
+#define CONFIG_ENV_SECT_SIZE	0x20000 /* 128K(one sector) for env */
+#define CONFIG_ENV_OFFSET	(CONFIG_SYS_MONITOR_LEN)
+
+/* Address and size of Redundant Environment Sector	*/
+#define CONFIG_ENV_OFFSET_REDUND	(CONFIG_ENV_OFFSET + \
+						CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE_REDUND	(CONFIG_ENV_SIZE)
+
+#else /* CFG_SYS_RAMBOOT */
+#define CONFIG_SYS_NO_FLASH		/* Flash is not usable now */
+#define CONFIG_ENV_IS_NOWHERE		/* Store ENV in memory only */
+#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - 0x1000)
+#define CONFIG_ENV_SIZE		0x2000
+#endif /* CFG_SYS_RAMBOOT */
+
+/* I2C */
+#define CONFIG_HARD_I2C		/* I2C with hardware support */
+#define CONFIG_FSL_I2C
+#define CONFIG_SYS_I2C_SPEED	200000	/* I2C speed and slave address */
+#define CONFIG_SYS_I2C_SLAVE	0x7F
+#define CONFIG_SYS_I2C_OFFSET	0x3000
+
+/* I2C SYSMON (LM75, AD7414 is almost compatible) */
+#define CONFIG_DTT_LM75		/* ON Semi's LM75 */
+#define CONFIG_DTT_SENSORS	{0, 1, 2, 3}	/* Sensor addresses */
+#define CONFIG_SYS_DTT_MAX_TEMP	70
+#define CONFIG_SYS_DTT_LOW_TEMP	-30
+#define CONFIG_SYS_DTT_HYSTERESIS	3
+#define CONFIG_SYS_DTT_BUS_NUM		(CONFIG_SYS_MAX_I2C_BUS)
+
+#if defined(CONFIG_CMD_NAND)
+#define CONFIG_NAND_KMETER1
+#define CONFIG_SYS_MAX_NAND_DEVICE	1
+#define CONFIG_SYS_NAND_BASE		CONFIG_SYS_PIGGY_BASE
+#endif
+
+#if defined(CONFIG_PCI)
+#define CONFIG_CMD_PCI
+#endif
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ		(8 << 20)
+
+/*
+ * Core HID Setup
+ */
+#define CONFIG_SYS_HID0_INIT		0x000000000
+#define CONFIG_SYS_HID0_FINAL		(HID0_ENABLE_MACHINE_CHECK | \
+					 HID0_ENABLE_INSTRUCTION_CACHE)
+#define CONFIG_SYS_HID2			HID2_HBE
+
+/*
+ * MMU Setup
+ */
+
+#define CONFIG_HIGH_BATS	1	/* High BATs supported */
+
+/* DDR: cache cacheable */
+#define CONFIG_SYS_IBAT0L	(CONFIG_SYS_SDRAM_BASE | BATL_PP_10 | \
+				BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_IBAT0U	(CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | \
+					BATU_VS | BATU_VP)
+#define CONFIG_SYS_DBAT0L	CONFIG_SYS_IBAT0L
+#define CONFIG_SYS_DBAT0U	CONFIG_SYS_IBAT0U
+
+/* IMMRBAR & PCI IO: cache-inhibit and guarded */
+#define CONFIG_SYS_IBAT1L	(CONFIG_SYS_IMMR | BATL_PP_10 | \
+				BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_IBAT1U	(CONFIG_SYS_IMMR | BATU_BL_4M | BATU_VS \
+					| BATU_VP)
+#define CONFIG_SYS_DBAT1L	CONFIG_SYS_IBAT1L
+#define CONFIG_SYS_DBAT1U	CONFIG_SYS_IBAT1U
+
+/* PRIO1, PIGGY:  icache cacheable, but dcache-inhibit and guarded */
+#define CONFIG_SYS_IBAT2L	(CONFIG_SYS_PIGGY_BASE | BATL_PP_10 | \
+					BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT2U	(CONFIG_SYS_PIGGY_BASE | BATU_BL_128M | \
+					BATU_VS | BATU_VP)
+#define CONFIG_SYS_DBAT2L	(CONFIG_SYS_PIGGY_BASE | BATL_PP_10 | \
+				 BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_DBAT2U	CONFIG_SYS_IBAT2U
+
+/* FLASH: icache cacheable, but dcache-inhibit and guarded */
+#define CONFIG_SYS_IBAT3L	(CONFIG_SYS_FLASH_BASE | BATL_PP_10 | \
+					BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT3U	(CONFIG_SYS_FLASH_BASE | BATU_BL_256M | \
+					BATU_VS | BATU_VP)
+#define CONFIG_SYS_DBAT3L	(CONFIG_SYS_FLASH_BASE | BATL_PP_10 | \
+				 BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_DBAT3U	CONFIG_SYS_IBAT3U
+
+/* Stack in dcache: cacheable, no memory coherence */
+#define CONFIG_SYS_IBAT4L	(CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_10)
+#define CONFIG_SYS_IBAT4U	(CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | \
+					BATU_VS | BATU_VP)
+#define CONFIG_SYS_DBAT4L	CONFIG_SYS_IBAT4L
+#define CONFIG_SYS_DBAT4U	CONFIG_SYS_IBAT4U
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD	0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM	0x02 /* Software reboot */
+
+#define BOOTFLASH_START	0xF0000000
+
+#define CONFIG_KM_CONSOLE_TTY	"ttyS0"
+
+/*
+ * Environment Configuration
+ */
+#define CONFIG_ENV_OVERWRITE
+#ifndef CONFIG_KM_DEF_ENV		/* if not set by keymile-common.h */
+#define CONFIG_KM_DEF_ENV "km-common=empty\0"
+#endif
+
+#ifndef CONFIG_KM_DEF_ROOTPATH
+#define CONFIG_KM_DEF_ROOTPATH		\
+	"rootpath=/opt/eldk/ppc_82xx\0"
+#endif
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+	CONFIG_KM_DEF_ENV						\
+	CONFIG_KM_DEF_ROOTPATH						\
+	"dtt_bus=pca9547:70:a\0"					\
+	"EEprom_ivm=pca9547:70:9\0"					\
+	"newenv="							\
+		"prot off 0xF00C0000 +0x40000 && "			\
+		"era 0xF00C0000 +0x40000\0"				\
+	"unlock=yes\0"							\
+	""
+
+#if defined(CONFIG_UEC_ETH)
+#define CONFIG_HAS_ETH0
+#endif
+
+#endif /* __CONFIG_KM83XX_H */