diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
index 196767a..1df6876 100644
--- a/drivers/spi/Kconfig
+++ b/drivers/spi/Kconfig
@@ -116,6 +116,14 @@
 	  access the SPI NOR flash on platforms embedding this Intel
 	  ICH IP core.
 
+config MT7621_SPI
+	bool "MediaTek MT7621 SPI driver"
+	depends on ARCH_MT7620
+	help
+	  Enable the MT7621 SPI driver. This driver can be used to access
+	  the SPI NOR flash on platforms embedding this Ralink / MediaTek
+	  SPI core, like MT7621/7628/7688.
+
 config MVEBU_A3700_SPI
 	bool "Marvell Armada 3700 SPI driver"
 	select CLK_ARMADA_3720
diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile
index ee99508..7242ea7 100644
--- a/drivers/spi/Makefile
+++ b/drivers/spi/Makefile
@@ -33,6 +33,7 @@
 obj-$(CONFIG_LPC32XX_SSP) += lpc32xx_ssp.o
 obj-$(CONFIG_MPC8XX_SPI) += mpc8xx_spi.o
 obj-$(CONFIG_MPC8XXX_SPI) += mpc8xxx_spi.o
+obj-$(CONFIG_MT7621_SPI) += mt7621_spi.o
 obj-$(CONFIG_MVEBU_A3700_SPI) += mvebu_a3700_spi.o
 obj-$(CONFIG_MXC_SPI) += mxc_spi.o
 obj-$(CONFIG_MXS_SPI) += mxs_spi.o
diff --git a/drivers/spi/mt7621_spi.c b/drivers/spi/mt7621_spi.c
new file mode 100644
index 0000000..107e58f
--- /dev/null
+++ b/drivers/spi/mt7621_spi.c
@@ -0,0 +1,312 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2018 Stefan Roese <sr@denx.de>
+ *
+ * Derived from the Linux driver version drivers/spi/spi-mt7621.c
+ *   Copyright (C) 2011 Sergiy <piratfm@gmail.com>
+ *   Copyright (C) 2011-2013 Gabor Juhos <juhosg@openwrt.org>
+ *   Copyright (C) 2014-2015 Felix Fietkau <nbd@nbd.name>
+ */
+
+#include <common.h>
+#include <dm.h>
+#include <spi.h>
+#include <wait_bit.h>
+#include <linux/io.h>
+
+#define SPI_MSG_SIZE_MAX	32	/* SPI message chunk size */
+/* Enough for SPI NAND page read / write with page size 2048 bytes */
+#define SPI_MSG_SIZE_OVERALL	(2048 + 16)
+
+#define MT7621_SPI_TRANS	0x00
+#define MT7621_SPI_TRANS_START	BIT(8)
+#define MT7621_SPI_TRANS_BUSY	BIT(16)
+
+#define MT7621_SPI_OPCODE	0x04
+#define MT7621_SPI_DATA0	0x08
+#define MT7621_SPI_DATA4	0x18
+#define MT7621_SPI_MASTER	0x28
+#define MT7621_SPI_MOREBUF	0x2c
+#define MT7621_SPI_POLAR	0x38
+
+#define MT7621_LSB_FIRST	BIT(3)
+#define MT7621_CPOL		BIT(4)
+#define MT7621_CPHA		BIT(5)
+
+#define MASTER_MORE_BUFMODE	BIT(2)
+#define MASTER_RS_CLK_SEL	GENMASK(27, 16)
+#define MASTER_RS_CLK_SEL_SHIFT	16
+#define MASTER_RS_SLAVE_SEL	GENMASK(31, 29)
+
+struct mt7621_spi {
+	void __iomem *base;
+	unsigned int sys_freq;
+	u32 data[(SPI_MSG_SIZE_OVERALL / 4) + 1];
+	int tx_len;
+};
+
+static void mt7621_spi_reset(struct mt7621_spi *rs, int duplex)
+{
+	setbits_le32(rs->base + MT7621_SPI_MASTER,
+		     MASTER_RS_SLAVE_SEL | MASTER_MORE_BUFMODE);
+}
+
+static void mt7621_spi_set_cs(struct mt7621_spi *rs, int cs, int enable)
+{
+	u32 val = 0;
+
+	debug("%s: cs#%d -> %s\n", __func__, cs, enable ? "enable" : "disable");
+	if (enable)
+		val = BIT(cs);
+	iowrite32(val, rs->base + MT7621_SPI_POLAR);
+}
+
+static int mt7621_spi_set_mode(struct udevice *bus, uint mode)
+{
+	struct mt7621_spi *rs = dev_get_priv(bus);
+	u32 reg;
+
+	debug("%s: mode=0x%08x\n", __func__, mode);
+	reg = ioread32(rs->base + MT7621_SPI_MASTER);
+
+	reg &= ~MT7621_LSB_FIRST;
+	if (mode & SPI_LSB_FIRST)
+		reg |= MT7621_LSB_FIRST;
+
+	reg &= ~(MT7621_CPHA | MT7621_CPOL);
+	switch (mode & (SPI_CPOL | SPI_CPHA)) {
+	case SPI_MODE_0:
+		break;
+	case SPI_MODE_1:
+		reg |= MT7621_CPHA;
+		break;
+	case SPI_MODE_2:
+		reg |= MT7621_CPOL;
+		break;
+	case SPI_MODE_3:
+		reg |= MT7621_CPOL | MT7621_CPHA;
+		break;
+	}
+	iowrite32(reg, rs->base + MT7621_SPI_MASTER);
+
+	return 0;
+}
+
+static int mt7621_spi_set_speed(struct udevice *bus, uint speed)
+{
+	struct mt7621_spi *rs = dev_get_priv(bus);
+	u32 rate;
+	u32 reg;
+
+	debug("%s: speed=%d\n", __func__, speed);
+	rate = DIV_ROUND_UP(rs->sys_freq, speed);
+	debug("rate:%u\n", rate);
+
+	if (rate > 4097)
+		return -EINVAL;
+
+	if (rate < 2)
+		rate = 2;
+
+	reg = ioread32(rs->base + MT7621_SPI_MASTER);
+	reg &= ~MASTER_RS_CLK_SEL;
+	reg |= (rate - 2) << MASTER_RS_CLK_SEL_SHIFT;
+	iowrite32(reg, rs->base + MT7621_SPI_MASTER);
+
+	return 0;
+}
+
+static inline int mt7621_spi_wait_till_ready(struct mt7621_spi *rs)
+{
+	int ret;
+
+	ret =  wait_for_bit_le32(rs->base + MT7621_SPI_TRANS,
+				 MT7621_SPI_TRANS_BUSY, 0, 10, 0);
+	if (ret)
+		pr_err("Timeout in %s!\n", __func__);
+
+	return ret;
+}
+
+static int mt7621_spi_xfer(struct udevice *dev, unsigned int bitlen,
+			   const void *dout, void *din, unsigned long flags)
+{
+	struct udevice *bus = dev->parent;
+	struct mt7621_spi *rs = dev_get_priv(bus);
+	const u8 *tx_buf = dout;
+	u8 *ptr = (u8 *)dout;
+	u8 *rx_buf = din;
+	int total_size = bitlen >> 3;
+	int chunk_size;
+	int rx_len = 0;
+	u32 data[(SPI_MSG_SIZE_MAX / 4) + 1] = { 0 };
+	u32 val;
+	int i;
+
+	debug("%s: dout=%p, din=%p, len=%x, flags=%lx\n", __func__, dout, din,
+	      total_size, flags);
+
+	/*
+	 * This driver only supports half-duplex, so complain and bail out
+	 * upon full-duplex messages
+	 */
+	if (dout && din) {
+		printf("Only half-duplex SPI transfer supported\n");
+		return -EIO;
+	}
+
+	if (dout) {
+		debug("TX-DATA: ");
+		for (i = 0; i < total_size; i++)
+			debug("%02x ", *ptr++);
+		debug("\n");
+	}
+
+	mt7621_spi_wait_till_ready(rs);
+
+	/*
+	 * Set CS active upon start of SPI message. This message can
+	 * be split upon multiple calls to this xfer function
+	 */
+	if (flags & SPI_XFER_BEGIN)
+		mt7621_spi_set_cs(rs, spi_chip_select(dev), 1);
+
+	while (total_size > 0) {
+		/* Don't exceed the max xfer size */
+		chunk_size = min_t(int, total_size, SPI_MSG_SIZE_MAX);
+
+		/*
+		 * We might have some TX data buffered from the last xfer
+		 * message. Make sure, that this does not exceed the max
+		 * xfer size
+		 */
+		if (rs->tx_len > 4)
+			chunk_size -= rs->tx_len;
+		if (din)
+			rx_len = chunk_size;
+
+		if (tx_buf) {
+			/* Check if this message does not exceed the buffer */
+			if ((chunk_size + rs->tx_len) > SPI_MSG_SIZE_OVERALL) {
+				printf("TX message size too big (%d)\n",
+				       chunk_size + rs->tx_len);
+				return -EMSGSIZE;
+			}
+
+			/*
+			 * Write all TX data into internal buffer to collect
+			 * all TX messages into one buffer (might be split into
+			 * multiple calls to this function)
+			 */
+			for (i = 0; i < chunk_size; i++, rs->tx_len++) {
+				rs->data[rs->tx_len / 4] |=
+					tx_buf[i] << (8 * (rs->tx_len & 3));
+			}
+		}
+
+		if (flags & SPI_XFER_END) {
+			/* Write TX data into controller */
+			if (rs->tx_len) {
+				rs->data[0] = swab32(rs->data[0]);
+				if (rs->tx_len < 4)
+					rs->data[0] >>= (4 - rs->tx_len) * 8;
+
+				for (i = 0; i < rs->tx_len; i += 4) {
+					iowrite32(rs->data[i / 4], rs->base +
+						  MT7621_SPI_OPCODE + i);
+				}
+			}
+
+			/* Write length into controller */
+			val = (min_t(int, rs->tx_len, 4) * 8) << 24;
+			if (rs->tx_len > 4)
+				val |= (rs->tx_len - 4) * 8;
+			val |= (rx_len * 8) << 12;
+			iowrite32(val, rs->base + MT7621_SPI_MOREBUF);
+
+			/* Start the xfer */
+			setbits_le32(rs->base + MT7621_SPI_TRANS,
+				     MT7621_SPI_TRANS_START);
+
+			/* Wait until xfer is finished on bus */
+			mt7621_spi_wait_till_ready(rs);
+
+			/* Reset TX length and TX buffer for next xfer */
+			rs->tx_len = 0;
+			memset(rs->data, 0, sizeof(rs->data));
+		}
+
+		for (i = 0; i < rx_len; i += 4)
+			data[i / 4] = ioread32(rs->base + MT7621_SPI_DATA0 + i);
+
+		if (rx_len) {
+			debug("RX-DATA: ");
+			for (i = 0; i < rx_len; i++) {
+				rx_buf[i] = data[i / 4] >> (8 * (i & 3));
+				debug("%02x ", rx_buf[i]);
+			}
+			debug("\n");
+		}
+
+		if (tx_buf)
+			tx_buf += chunk_size;
+		if (rx_buf)
+			rx_buf += chunk_size;
+		total_size -= chunk_size;
+	}
+
+	/* Wait until xfer is finished on bus and de-assert CS */
+	mt7621_spi_wait_till_ready(rs);
+	if (flags & SPI_XFER_END)
+		mt7621_spi_set_cs(rs, spi_chip_select(dev), 0);
+
+	return 0;
+}
+
+static int mt7621_spi_probe(struct udevice *dev)
+{
+	struct mt7621_spi *rs = dev_get_priv(dev);
+
+	rs->base = dev_remap_addr(dev);
+	if (!rs->base)
+		return -EINVAL;
+
+	/*
+	 * Read input clock via DT for now. At some point this should be
+	 * replaced by implementing a clock driver for this SoC and getting
+	 * the SPI frequency via this clock driver.
+	 */
+	rs->sys_freq = dev_read_u32_default(dev, "clock-frequency", 0);
+	if (!rs->sys_freq) {
+		printf("Please provide clock-frequency!\n");
+		return -EINVAL;
+	}
+
+	mt7621_spi_reset(rs, 0);
+
+	return 0;
+}
+
+static const struct dm_spi_ops mt7621_spi_ops = {
+	.set_mode = mt7621_spi_set_mode,
+	.set_speed = mt7621_spi_set_speed,
+	.xfer = mt7621_spi_xfer,
+	/*
+	 * cs_info is not needed, since we require all chip selects to be
+	 * in the device tree explicitly
+	 */
+};
+
+static const struct udevice_id mt7621_spi_ids[] = {
+	{ .compatible = "ralink,mt7621-spi" },
+	{ }
+};
+
+U_BOOT_DRIVER(mt7621_spi) = {
+	.name = "mt7621_spi",
+	.id = UCLASS_SPI,
+	.of_match = mt7621_spi_ids,
+	.ops = &mt7621_spi_ops,
+	.priv_auto_alloc_size = sizeof(struct mt7621_spi),
+	.probe = mt7621_spi_probe,
+};