ppc4xx: Big header cleanup, mostly PPC440 related
This patch starts a bit PPC4xx header cleanup. First patch mostly
touches PPC440 files. A later patch will touch the PPC405 files as well.
This cleanup is done by creating header files for all SoC versions and
moving the SoC specific defines into these special headers. This way the
common header ppc405.h and ppc440.h can be cleaned up finally.
Signed-off-by: Stefan Roese <sr@denx.de>
diff --git a/arch/powerpc/cpu/ppc4xx/44x_spd_ddr2.c b/arch/powerpc/cpu/ppc4xx/44x_spd_ddr2.c
index 3923fee..cf9d66d 100644
--- a/arch/powerpc/cpu/ppc4xx/44x_spd_ddr2.c
+++ b/arch/powerpc/cpu/ppc4xx/44x_spd_ddr2.c
@@ -469,7 +469,7 @@
/*------------------------------------------------------------------
* Reset the DDR-SDRAM controller.
*-----------------------------------------------------------------*/
- mtsdr(SDR0_SRST, (0x80000000 >> 10));
+ mtsdr(SDR0_SRST, SDR0_SRST0_DMC);
mtsdr(SDR0_SRST, 0x00000000);
/*
diff --git a/arch/powerpc/cpu/ppc4xx/4xx_pci.c b/arch/powerpc/cpu/ppc4xx/4xx_pci.c
index bfba952..80b0c1c 100644
--- a/arch/powerpc/cpu/ppc4xx/4xx_pci.c
+++ b/arch/powerpc/cpu/ppc4xx/4xx_pci.c
@@ -594,35 +594,35 @@
* Set priority for all PLB3 devices to 0.
* Set PLB3 arbiter to fair mode.
*/
- mfsdr(SD0_AMP1, reg);
- mtsdr(SD0_AMP1, (reg & 0x000000FF) | 0x0000FF00);
- reg = mfdcr(PLB3_ACR);
- mtdcr(PLB3_ACR, reg | 0x80000000);
+ mfsdr(SDR0_AMP1, reg);
+ mtsdr(SDR0_AMP1, (reg & 0x000000FF) | 0x0000FF00);
+ reg = mfdcr(PLB3A0_ACR);
+ mtdcr(PLB3A0_ACR, reg | 0x80000000);
/*
* Set priority for all PLB4 devices to 0.
*/
- mfsdr(SD0_AMP0, reg);
- mtsdr(SD0_AMP0, (reg & 0x000000FF) | 0x0000FF00);
- reg = mfdcr(PLB4_ACR) | 0xa0000000;
- mtdcr(PLB4_ACR, reg);
+ mfsdr(SDR0_AMP0, reg);
+ mtsdr(SDR0_AMP0, (reg & 0x000000FF) | 0x0000FF00);
+ reg = mfdcr(PLB4A0_ACR) | 0xa0000000;
+ mtdcr(PLB4A0_ACR, reg);
/*
* Set Nebula PLB4 arbiter to fair mode.
*/
/* Segment0 */
- reg = (mfdcr(PLB0_ACR) & ~PLB0_ACR_PPM_MASK) | PLB0_ACR_PPM_FAIR;
- reg = (reg & ~PLB0_ACR_HBU_MASK) | PLB0_ACR_HBU_ENABLED;
- reg = (reg & ~PLB0_ACR_RDP_MASK) | PLB0_ACR_RDP_4DEEP;
- reg = (reg & ~PLB0_ACR_WRP_MASK) | PLB0_ACR_WRP_2DEEP;
- mtdcr(PLB0_ACR, reg);
+ reg = (mfdcr(PLB4A0_ACR) & ~PLB4Ax_ACR_PPM_MASK) | PLB4Ax_ACR_PPM_FAIR;
+ reg = (reg & ~PLB4Ax_ACR_HBU_MASK) | PLB4Ax_ACR_HBU_ENABLED;
+ reg = (reg & ~PLB4Ax_ACR_RDP_MASK) | PLB4Ax_ACR_RDP_4DEEP;
+ reg = (reg & ~PLB4Ax_ACR_WRP_MASK) | PLB4Ax_ACR_WRP_2DEEP;
+ mtdcr(PLB4A0_ACR, reg);
/* Segment1 */
- reg = (mfdcr(PLB1_ACR) & ~PLB1_ACR_PPM_MASK) | PLB1_ACR_PPM_FAIR;
- reg = (reg & ~PLB1_ACR_HBU_MASK) | PLB1_ACR_HBU_ENABLED;
- reg = (reg & ~PLB1_ACR_RDP_MASK) | PLB1_ACR_RDP_4DEEP;
- reg = (reg & ~PLB1_ACR_WRP_MASK) | PLB1_ACR_WRP_2DEEP;
- mtdcr(PLB1_ACR, reg);
+ reg = (mfdcr(PLB4A1_ACR) & ~PLB4Ax_ACR_PPM_MASK) | PLB4Ax_ACR_PPM_FAIR;
+ reg = (reg & ~PLB4Ax_ACR_HBU_MASK) | PLB4Ax_ACR_HBU_ENABLED;
+ reg = (reg & ~PLB4Ax_ACR_RDP_MASK) | PLB4Ax_ACR_RDP_4DEEP;
+ reg = (reg & ~PLB4Ax_ACR_WRP_MASK) | PLB4Ax_ACR_WRP_2DEEP;
+ mtdcr(PLB4A1_ACR, reg);
#if defined(CONFIG_SYS_PCI_BOARD_FIXUP_IRQ)
hose->fixup_irq = board_pci_fixup_irq;
diff --git a/arch/powerpc/cpu/ppc4xx/cpu.c b/arch/powerpc/cpu/ppc4xx/cpu.c
index 39b8e2f..8485218 100644
--- a/arch/powerpc/cpu/ppc4xx/cpu.c
+++ b/arch/powerpc/cpu/ppc4xx/cpu.c
@@ -98,8 +98,8 @@
#if defined(CONFIG_440GX) || defined(CONFIG_440SP) || defined(CONFIG_440SPE)
unsigned long val;
- mfsdr(SDR0_XCR, val);
- return (val & 0x80000000);
+ mfsdr(SDR0_XCR0, val);
+ return (val & SDR0_XCR0_PAE_MASK);
#endif
#if defined(CONFIG_440EP) || defined(CONFIG_440GR) || \
defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \
@@ -107,7 +107,7 @@
unsigned long val;
mfsdr(SDR0_PCI0, val);
- return (val & 0x80000000);
+ return (val & SDR0_PCI0_PAE_MASK);
#endif
}
#endif
@@ -262,7 +262,7 @@
#endif /* SDR0_PINSTP_SHIFT */
-#if defined(CONFIG_440)
+#if defined(CONFIG_440GP)
static int do_chip_reset (unsigned long sys0, unsigned long sys1)
{
/* Changes to CPC0_SYS0 and CPC0_SYS1 require chip
@@ -276,7 +276,7 @@
return 1;
}
-#endif
+#endif /* CONFIG_440GP */
int checkcpu (void)
@@ -417,6 +417,7 @@
break;
#if defined(CONFIG_440)
+#if defined(CONFIG_440GP)
case PVR_440GP_RB:
puts("GP Rev. B");
/* See errata 1.12: CHIP_4 */
@@ -433,6 +434,7 @@
case PVR_440GP_RC:
puts("GP Rev. C");
break;
+#endif /* CONFIG_440GP */
case PVR_440GX_RA:
puts("GX Rev. A");
diff --git a/arch/powerpc/cpu/ppc4xx/cpu_init.c b/arch/powerpc/cpu/ppc4xx/cpu_init.c
index 6456dc7..677a4b5 100644
--- a/arch/powerpc/cpu/ppc4xx/cpu_init.c
+++ b/arch/powerpc/cpu/ppc4xx/cpu_init.c
@@ -397,10 +397,10 @@
/*
* Set PLB4 arbiter (Segment 0 and 1) to 4 deep pipeline read
*/
- mtdcr(PLB0_ACR, (mfdcr(PLB0_ACR) & ~PLB0_ACR_RDP_MASK) |
- PLB0_ACR_RDP_4DEEP);
- mtdcr(PLB1_ACR, (mfdcr(PLB1_ACR) & ~PLB1_ACR_RDP_MASK) |
- PLB1_ACR_RDP_4DEEP);
+ mtdcr(PLB4A0_ACR, (mfdcr(PLB4A0_ACR) & ~PLB4Ax_ACR_RDP_MASK) |
+ PLB4Ax_ACR_RDP_4DEEP);
+ mtdcr(PLB4A1_ACR, (mfdcr(PLB4A1_ACR) & ~PLB4Ax_ACR_RDP_MASK) |
+ PLB4Ax_ACR_RDP_4DEEP);
#endif /* CONFIG_440SP/SPE || CONFIG_460EX/GT || CONFIG_405EX */
}
diff --git a/arch/powerpc/cpu/ppc4xx/reginfo.c b/arch/powerpc/cpu/ppc4xx/reginfo.c
index 88f8429..2f1ab9e 100644
--- a/arch/powerpc/cpu/ppc4xx/reginfo.c
+++ b/arch/powerpc/cpu/ppc4xx/reginfo.c
@@ -108,9 +108,9 @@
{"SDR0_SDSTP3", IDCR6, SDR0_SDSTP3},
{"SDR0_CUST0", IDCR6, SDR0_CUST0},
{"SDR0_CUST1", IDCR6, SDR0_CUST1},
- {"SDR0_EBC0", IDCR6, SDR0_EBC0},
- {"SDR0_AMP0", IDCR6, SD0_AMP0},
- {"SDR0_AMP1", IDCR6, SD0_AMP1},
+ {"SDR0_EBC", IDCR6, SDR0_EBC},
+ {"SDR0_AMP0", IDCR6, SDR0_AMP0},
+ {"SDR0_AMP1", IDCR6, SDR0_AMP1},
{"SDR0_CP440", IDCR6, SDR0_CP440},
{"SDR0_CRYP0", IDCR6, SDR0_CRYP0},
{"SDR0_DDRCFG", IDCR6, SDR0_DDRCFG},
diff --git a/arch/powerpc/include/asm/ppc405.h b/arch/powerpc/include/asm/ppc405.h
index bc2d051..e0d165e 100644
--- a/arch/powerpc/include/asm/ppc405.h
+++ b/arch/powerpc/include/asm/ppc405.h
@@ -34,6 +34,9 @@
#define CONFIG_SYS_DCACHE_SIZE (2 << 10) /* For PLX IOP480(403)*/
#endif
+/* DCR registers */
+#define PLB0_ACR 0x0087
+
/******************************************************************************
* Special for PPC405GP
******************************************************************************/
@@ -527,14 +530,10 @@
#endif /* #ifndef CONFIG_IOP480 */
#endif /* #ifdef CONFIG_405EP */
+#if 0
/******************************************************************************
* Memory Access Layer
******************************************************************************/
-#if defined(CONFIG_405EZ)
-#define MAL_DCR_BASE 0x380
-#else
-#define MAL_DCR_BASE 0x180
-#endif
#define MAL0_CFG (MAL_DCR_BASE + 0x00) /* MAL Config reg */
#define MAL0_ESR (MAL_DCR_BASE + 0x01) /* Err Status (Read/Clear) */
#define MAL0_IER (MAL_DCR_BASE + 0x02) /* Interrupt enable */
@@ -564,6 +563,7 @@
#define MAL0_RCBS8 (MAL_DCR_BASE + 0x68) /* RX 8 Channel buffer size */
#define MAL0_RCBS16 (MAL_DCR_BASE + 0x70) /* RX 16 Channel buffer size */
#define MAL0_RCBS24 (MAL_DCR_BASE + 0x78) /* RX 24 Channel buffer size */
+#endif
/*-----------------------------------------------------------------------------
| UART Register Offsets
@@ -806,27 +806,4 @@
#define SDR0_PFC1_GPT_FREQ 0x0000000f
#endif
-/* General Purpose Timer (GPT) Register Offsets */
-#define GPT0_TBC 0x00000000
-#define GPT0_IM 0x00000018
-#define GPT0_ISS 0x0000001C
-#define GPT0_ISC 0x00000020
-#define GPT0_IE 0x00000024
-#define GPT0_COMP0 0x00000080
-#define GPT0_COMP1 0x00000084
-#define GPT0_COMP2 0x00000088
-#define GPT0_COMP3 0x0000008C
-#define GPT0_COMP4 0x00000090
-#define GPT0_COMP5 0x00000094
-#define GPT0_COMP6 0x00000098
-#define GPT0_MASK0 0x000000C0
-#define GPT0_MASK1 0x000000C4
-#define GPT0_MASK2 0x000000C8
-#define GPT0_MASK3 0x000000CC
-#define GPT0_MASK4 0x000000D0
-#define GPT0_MASK5 0x000000D4
-#define GPT0_MASK6 0x000000D8
-#define GPT0_DCT0 0x00000110
-#define GPT0_DCIS 0x0000011C
-
#endif /* __PPC405_H__ */
diff --git a/arch/powerpc/include/asm/ppc405cr.h b/arch/powerpc/include/asm/ppc405cr.h
new file mode 100644
index 0000000..53a6ce8
--- /dev/null
+++ b/arch/powerpc/include/asm/ppc405cr.h
@@ -0,0 +1,26 @@
+/*
+ * (C) Copyright 2010
+ * Stefan Roese, DENX Software Engineering, sr@denx.de.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef _PPC405CR_H_
+#define _PPC405CR_H_
+
+#define CONFIG_SDRAM_PPC4xx_IBM_SDRAM /* IBM SDRAM controller */
+
+#endif /* _PPC405CR_H_ */
diff --git a/arch/powerpc/include/asm/ppc405ep.h b/arch/powerpc/include/asm/ppc405ep.h
new file mode 100644
index 0000000..38b1205
--- /dev/null
+++ b/arch/powerpc/include/asm/ppc405ep.h
@@ -0,0 +1,26 @@
+/*
+ * (C) Copyright 2010
+ * Stefan Roese, DENX Software Engineering, sr@denx.de.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef _PPC405EP_H_
+#define _PPC405EP_H_
+
+#define CONFIG_SDRAM_PPC4xx_IBM_SDRAM /* IBM SDRAM controller */
+
+#endif /* _PPC405EP_H_ */
diff --git a/arch/powerpc/include/asm/ppc405ex.h b/arch/powerpc/include/asm/ppc405ex.h
new file mode 100644
index 0000000..f2c860a
--- /dev/null
+++ b/arch/powerpc/include/asm/ppc405ex.h
@@ -0,0 +1,30 @@
+/*
+ * (C) Copyright 2010
+ * Stefan Roese, DENX Software Engineering, sr@denx.de.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef _PPC405EX_H_
+#define _PPC405EX_H_
+
+#define CONFIG_SDRAM_PPC4xx_IBM_DDR2 /* IBM DDR(2) controller */
+
+#define CONFIG_NAND_NDFC
+
+#define CONFIG_SYS_PPC4xx_PLB4_ARBITER
+
+#endif /* _PPC405EX_H_ */
diff --git a/arch/powerpc/include/asm/ppc405ez.h b/arch/powerpc/include/asm/ppc405ez.h
new file mode 100644
index 0000000..69baa20
--- /dev/null
+++ b/arch/powerpc/include/asm/ppc405ez.h
@@ -0,0 +1,28 @@
+/*
+ * (C) Copyright 2010
+ * Stefan Roese, DENX Software Engineering, sr@denx.de.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef _PPC405EZ_H_
+#define _PPC405EZ_H_
+
+#define CONFIG_NAND_NDFC
+
+#define MAL_DCR_BASE 0x380
+
+#endif /* _PPC405EZ_H_ */
diff --git a/arch/powerpc/include/asm/ppc405gp.h b/arch/powerpc/include/asm/ppc405gp.h
new file mode 100644
index 0000000..50e0a19
--- /dev/null
+++ b/arch/powerpc/include/asm/ppc405gp.h
@@ -0,0 +1,26 @@
+/*
+ * (C) Copyright 2010
+ * Stefan Roese, DENX Software Engineering, sr@denx.de.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef _PPC405GP_H_
+#define _PPC405GP_H_
+
+#define CONFIG_SDRAM_PPC4xx_IBM_SDRAM /* IBM SDRAM controller */
+
+#endif /* _PPC405GP_H_ */
diff --git a/arch/powerpc/include/asm/ppc440.h b/arch/powerpc/include/asm/ppc440.h
index 6727753..766ea2a 100644
--- a/arch/powerpc/include/asm/ppc440.h
+++ b/arch/powerpc/include/asm/ppc440.h
@@ -29,6 +29,9 @@
* Alain Saurel, AMCC/IBM, alain.saurel@fr.ibm.com
* Robert Snyder, AMCC/IBM, rob.snyder@fr.ibm.com
*
+ * (C) Copyright 2010
+ * Stefan Roese, DENX Software Engineering, sr@denx.de.
+ *
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
@@ -50,14 +53,19 @@
#define CONFIG_SYS_DCACHE_SIZE (32 << 10) /* For AMCC 440 CPUs */
-/******************************************************************************
+/*
* DCRs & Related
- ******************************************************************************/
+ */
-/*-----------------------------------------------------------------------------
- | Clocking Controller
- +----------------------------------------------------------------------------*/
-/* values for clkcfga register - indirect addressing of these regs */
+/* Memory mapped registers */
+#define PCIL0_CFGADR (CONFIG_SYS_PCI_BASE + 0x0ec00000)
+#define PCIL0_CFGDATA (CONFIG_SYS_PCI_BASE + 0x0ec00004)
+#define PCIL0_CFGBASE (CONFIG_SYS_PCI_BASE + 0x0ec80000)
+#define PCIL0_IOBASE (CONFIG_SYS_PCI_BASE + 0x08000000)
+
+/* DCR registers */
+
+/* CPR register declarations */
#define CPR0_PLLC 0x0040
#define CPR0_PLLD 0x0060
#define CPR0_PRIMAD0 0x0080
@@ -68,108 +76,64 @@
#define CPR0_SPCID 0x0120
#define CPR0_ICFG 0x0140
-/* 440EPX boot strap options */
-#define BOOT_STRAP_OPTION_A 0x00000000
-#define BOOT_STRAP_OPTION_B 0x00000001
-#define BOOT_STRAP_OPTION_D 0x00000003
-#define BOOT_STRAP_OPTION_E 0x00000004
-
-/* 440gx sdr register definations */
-#define SDR0_SDSTP0 0x0020 /* */
-#define SDR0_SDSTP1 0x0021 /* */
+/* SDR register definations */
+#define SDR0_SDSTP0 0x0020
+#define SDR0_SDSTP1 0x0021
#define SDR0_PINSTP 0x0040
#define SDR0_SDCS0 0x0060
-#if defined(CONFIG_440EPX) || defined(CONFIG_440GRX)
-#define SDR0_DDRCFG 0x00e0
-#endif /* defined(CONFIG_440EPX) || defined(CONFIG_440GRX) */
+#define SDR0_ECID0 0x0080
+#define SDR0_ECID1 0x0081
+#define SDR0_ECID2 0x0082
+#define SDR0_ECID3 0x0083
+#define SDR0_DDR0 0x00e1
#define SDR0_EBC 0x0100
-#define SDR0_UART0 0x0120 /* UART0 Config */
-#define SDR0_UART1 0x0121 /* UART1 Config */
-#define SDR0_UART2 0x0122 /* UART2 Config */
-#define SDR0_UART3 0x0123 /* UART3 Config */
+#define SDR0_UART0 0x0120
+#define SDR0_UART1 0x0121
+#define SDR0_UART2 0x0122
+#define SDR0_UART3 0x0123
#define SDR0_CP440 0x0180
#define SDR0_XCR 0x01c0
+#define SDR0_XCR0 0x01c0
#define SDR0_XPLLC 0x01c1
#define SDR0_XPLLD 0x01c2
#define SDR0_SRST 0x0200
-#define SD0_AMP0 0x0240 /* Override PLB4 prioritiy for up to 8 masters */
-#define SD0_AMP1 0x0241 /* Override PLB3 prioritiy for up to 8 masters */
-#if defined(CONFIG_460EX) || defined(CONFIG_460GT)
-#define SDR0_PCI0 0x01c0
-#else
-#define SDR0_PCI0 0x0300
-#endif
+#define SDR0_SRST0 SDR0_SRST
+#define SDR0_SRST1 0x0201
+#define SDR0_AMP0 0x0240
+#define SDR0_AMP1 0x0241
#define SDR0_USB0 0x0320
#define SDR0_CUST0 0x4000
#define SDR0_CUST1 0x4002
-#define SDR0_PFC0 0x4100 /* Pin Function 0 */
-#define SDR0_PFC1 0x4101 /* Pin Function 1 */
-#define SDR0_MFR 0x4300 /* SDR0_MFR reg */
-
-#if defined(CONFIG_440GX)
-#define SD0_AMP 0x0240
-#define SDR0_XPLLC 0x01c1
-#define SDR0_XPLLD 0x01c2
-#define SDR0_XCR 0x01c0
-#define SDR0_SDSTP2 0x4001
-#define SDR0_SDSTP3 0x4003
-#endif /* CONFIG_440GX */
-
-/*----------------------------------------------------------------------------+
-| Core Configuration/MMU configuration for 440 (CCR1 for 440x5 only).
-+----------------------------------------------------------------------------*/
-#define CCR0_PRE 0x40000000
-#define CCR0_CRPE 0x08000000
-#define CCR0_DSTG 0x00200000
-#define CCR0_DAPUIB 0x00100000
-#define CCR0_DTB 0x00008000
-#define CCR0_GICBT 0x00004000
-#define CCR0_GDCBT 0x00002000
-#define CCR0_FLSTA 0x00000100
-#define CCR0_ICSLC_MASK 0x0000000C
-#define CCR0_ICSLT_MASK 0x00000003
-#define CCR1_TCS_MASK 0x00000080
-#define CCR1_TCS_INTCLK 0x00000000
-#define CCR1_TCS_EXTCLK 0x00000080
-#define MMUCR_SWOA 0x01000000
-#define MMUCR_U1TE 0x00400000
-#define MMUCR_U2SWOAE 0x00200000
-#define MMUCR_DULXE 0x00800000
-#define MMUCR_IULXE 0x00400000
-#define MMUCR_STS 0x00100000
-#define MMUCR_STID_MASK 0x000000FF
-
-#ifdef CONFIG_440SPE
-#undef SDR0_SDSTP2
-#define SDR0_SDSTP2 0x0022
-#undef SDR0_SDSTP3
-#define SDR0_SDSTP3 0x0023
-#define SDR0_DDR0 0x00E1
-#define SDR0_UART2 0x0122
-#define SDR0_XCR0 0x01c0
-#define SDR0_XCR1 0x01c3
-#define SDR0_XCR2 0x01c6
-#define SDR0_XPLLC0 0x01c1
-#define SDR0_XPLLD0 0x01c2
-#define SDR0_XPLLC1 0x01c4 /* notRCW - SG */
-#define SDR0_XPLLD1 0x01c5 /* notRCW - SG */
-#define SDR0_XPLLC2 0x01c7 /* notRCW - SG */
-#define SDR0_XPLLD2 0x01c8 /* dnotRCW - SG */
-#define SD0_AMP0 0x0240
-#define SD0_AMP1 0x0241
#define SDR0_CUST2 0x4004
#define SDR0_CUST3 0x4006
-#define SDR0_SDSTP4 0x4001
-#define SDR0_SDSTP5 0x4003
-#define SDR0_SDSTP6 0x4005
-#define SDR0_SDSTP7 0x4007
+#define SDR0_PFC0 0x4100
+#define SDR0_PFC1 0x4101
+#define SDR0_PFC2 0x4102
+#define SDR0_PFC4 0x4104
+#define SDR0_MFR 0x4300
-#endif /* CONFIG_440SPE */
+#define SDR0_DDR0_DDRM_DECODE(n) ((((u32)(n)) >> 29) & 0x03)
-/*-----------------------------------------------------------------------------
- | External Bus Controller
- +----------------------------------------------------------------------------*/
-/* values for EBC0_CFGADDR register - indirect addressing of these regs */
+#define SDR0_PCI0_PAE_MASK (0x80000000 >> 0)
+#define SDR0_XCR0_PAE_MASK (0x80000000 >> 0)
+
+#define SDR0_PFC0_GEIE_MASK 0x00003e00
+#define SDR0_PFC0_GEIE_TRE 0x00003e00
+#define SDR0_PFC0_GEIE_NOTRE 0x00000000
+#define SDR0_PFC0_TRE_MASK (0x80000000 >> 23)
+#define SDR0_PFC0_TRE_DISABLE 0x00000000
+#define SDR0_PFC0_TRE_ENABLE (0x80000000 >> 23)
+
+/*
+ * Core Configuration/MMU configuration for 440
+ */
+#define CCR0_DAPUIB 0x00100000
+#define CCR0_DTB 0x00008000
+
+/*
+ * External Bus Controller
+ */
+/* Values for EBC0_CFGADDR register - indirect addressing of these regs */
#define PB0CR 0x00 /* periph bank 0 config reg */
#define PB1CR 0x01 /* periph bank 1 config reg */
#define PB2CR 0x02 /* periph bank 2 config reg */
@@ -190,1583 +154,9 @@
#define PBESR 0x21 /* periph bus error status reg */
#define EBC0_CFG 0x23 /* external bus configuration reg */
-#if defined(CONFIG_440EP) || defined(CONFIG_440GR) || \
- defined(CONFIG_440EPX) || defined(CONFIG_440GRX)
+#define SDR0_SDCS_SDD (0x80000000 >> 31)
- /* PLB3 Arbiter */
-#define PLB3_DCR_BASE 0x070
-#define PLB3_ACR (PLB3_DCR_BASE + 0x7)
-
- /* PLB4 Arbiter - PowerPC440EP Pass1 */
-#define PLB4_DCR_BASE 0x080
-#define PLB4_ACR (PLB4_DCR_BASE + 0x1)
-
-#define PLB4_ACR_WRP (0x80000000 >> 7)
-
- /* Pin Function Control Register 1 */
-#define SDR0_PFC1 0x4101
-#define SDR0_PFC1_U1ME_MASK 0x02000000 /* UART1 Mode Enable */
-#define SDR0_PFC1_U1ME_DSR_DTR 0x00000000 /* UART1 in DSR/DTR Mode */
-#define SDR0_PFC1_U1ME_CTS_RTS 0x02000000 /* UART1 in CTS/RTS Mode */
-#define SDR0_PFC1_U0ME_MASK 0x00080000 /* UART0 Mode Enable */
-#define SDR0_PFC1_U0ME_DSR_DTR 0x00000000 /* UART0 in DSR/DTR Mode */
-#define SDR0_PFC1_U0ME_CTS_RTS 0x00080000 /* UART0 in CTS/RTS Mode */
-#define SDR0_PFC1_U0IM_MASK 0x00040000 /* UART0 Interface Mode */
-#define SDR0_PFC1_U0IM_8PINS 0x00000000 /* UART0 Interface Mode 8 pins */
-#define SDR0_PFC1_U0IM_4PINS 0x00040000 /* UART0 Interface Mode 4 pins */
-#define SDR0_PFC1_SIS_MASK 0x00020000 /* SCP or IIC1 Selection */
-#define SDR0_PFC1_SIS_SCP_SEL 0x00000000 /* SCP Selected */
-#define SDR0_PFC1_SIS_IIC1_SEL 0x00020000 /* IIC1 Selected */
-#define SDR0_PFC1_UES_MASK 0x00010000 /* USB2D_RX_Active / EBC_Hold
- Req Selection */
-#define SDR0_PFC1_UES_USB2D_SEL 0x00000000 /* USB2D_RX_Active Selected */
-#define SDR0_PFC1_UES_EBCHR_SEL 0x00010000 /* EBC_Hold Req Selected */
-#define SDR0_PFC1_DIS_MASK 0x00008000 /* DMA_Req(1) / UIC_IRQ(5)
- Selection */
-#define SDR0_PFC1_DIS_DMAR_SEL 0x00000000 /* DMA_Req(1) Selected */
-#define SDR0_PFC1_DIS_UICIRQ5_SEL 0x00008000 /* UIC_IRQ(5) Selected */
-#define SDR0_PFC1_ERE_MASK 0x00004000 /* EBC Mast.Ext.Req.En./GPIO0(27)
- Selection */
-#define SDR0_PFC1_ERE_EXTR_SEL 0x00000000 /* EBC Mast.Ext.Req.En.
- Selected */
-#define SDR0_PFC1_ERE_GPIO0_27_SEL 0x00004000 /* GPIO0(27) Selected */
-#define SDR0_PFC1_UPR_MASK 0x00002000 /* USB2 Device Packet Reject
- Selection */
-#define SDR0_PFC1_UPR_DISABLE 0x00000000 /* USB2 Device Packet Reject
- Disable */
-#define SDR0_PFC1_UPR_ENABLE 0x00002000 /* USB2 Device Packet Reject
- Enable */
-
-#define SDR0_PFC1_PLB_PME_MASK 0x00001000 /* PLB3/PLB4 Perf. Monitor Enable
- Selection */
-#define SDR0_PFC1_PLB_PME_PLB3_SEL 0x00000000 /* PLB3 Performance Monitor
- Enable */
-#define SDR0_PFC1_PLB_PME_PLB4_SEL 0x00001000 /* PLB3 Performance Monitor
- Enable */
-#define SDR0_PFC1_GFGGI_MASK 0x0000000F /* GPT Frequency Generation
- Gated In */
-
- /* USB Control Register */
-#define SDR0_USB0 0x0320
-#define SDR0_USB0_USB_DEVSEL_MASK 0x00000002 /* USB Device Selection */
-#define SDR0_USB0_USB20D_DEVSEL 0x00000000 /* USB2.0 Device Selected */
-#define SDR0_USB0_USB11D_DEVSEL 0x00000002 /* USB1.1 Device Selected */
-#define SDR0_USB0_LEEN_MASK 0x00000001 /* Little Endian selection */
-#define SDR0_USB0_LEEN_DISABLE 0x00000000 /* Little Endian Disable */
-#define SDR0_USB0_LEEN_ENABLE 0x00000001 /* Little Endian Enable */
-
- /* Miscealleneaous Function Reg. */
-#define SDR0_MFR 0x4300
-#define SDR0_MFR_ETH0_CLK_SEL_MASK 0x08000000 /* Ethernet0 Clock Select */
-#define SDR0_MFR_ETH0_CLK_SEL_EXT 0x00000000
-#define SDR0_MFR_ETH1_CLK_SEL_MASK 0x04000000 /* Ethernet1 Clock Select */
-#define SDR0_MFR_ETH1_CLK_SEL_EXT 0x00000000
-#define SDR0_MFR_ZMII_MODE_MASK 0x03000000 /* ZMII Mode Mask */
-#define SDR0_MFR_ZMII_MODE_MII 0x00000000 /* ZMII Mode MII */
-#define SDR0_MFR_ZMII_MODE_SMII 0x01000000 /* ZMII Mode SMII */
-#define SDR0_MFR_ZMII_MODE_RMII_10M 0x02000000 /* ZMII Mode RMII - 10 Mbs */
-#define SDR0_MFR_ZMII_MODE_RMII_100M 0x03000000 /* ZMII Mode RMII - 100 Mbs */
-#define SDR0_MFR_ZMII_MODE_BIT0 0x02000000 /* ZMII Mode Bit0 */
-#define SDR0_MFR_ZMII_MODE_BIT1 0x01000000 /* ZMII Mode Bit1 */
-#define SDR0_MFR_ZM_ENCODE(n) ((((unsigned long)(n))&0x3)<<24)
-#define SDR0_MFR_ZM_DECODE(n) ((((unsigned long)(n))<<24)&0x3)
-
-#define SDR0_MFR_ERRATA3_EN0 0x00800000
-#define SDR0_MFR_ERRATA3_EN1 0x00400000
-#define SDR0_MFR_PKT_REJ_MASK 0x00180000 /* Pkt Rej. Enable Mask */
-#define SDR0_MFR_PKT_REJ_EN 0x00180000 /* Pkt Rej. Ena. on both EMAC3 0-1 */
-#define SDR0_MFR_PKT_REJ_EN0 0x00100000 /* Pkt Rej. Enable on EMAC3(0) */
-#define SDR0_MFR_PKT_REJ_EN1 0x00080000 /* Pkt Rej. Enable on EMAC3(1) */
-#define SDR0_MFR_PKT_REJ_POL 0x00200000 /* Packet Reject Polarity */
-
-#define GPT0_COMP6 0x00000098
-#define GPT0_COMP5 0x00000094
-#define GPT0_COMP4 0x00000090
-#define GPT0_COMP3 0x0000008C
-#define GPT0_COMP2 0x00000088
-#define GPT0_COMP1 0x00000084
-
-#define GPT0_MASK6 0x000000D8
-#define GPT0_MASK5 0x000000D4
-#define GPT0_MASK4 0x000000D0
-#define GPT0_MASK3 0x000000CC
-#define GPT0_MASK2 0x000000C8
-#define GPT0_MASK1 0x000000C4
-
-#if defined(CONFIG_440EPX) || defined(CONFIG_440GRX)
-#define SDR0_USB2D0CR 0x0320
-#define SDR0_USB2D0CR_USB2DEV_EBC_SEL_MASK 0x00000004 /* USB 2.0 Device/EBC
- Master Selection */
-#define SDR0_USB2D0CR_USB2DEV_SELECTION 0x00000004 /* USB 2.0 Device Selection*/
-#define SDR0_USB2D0CR_EBC_SELECTION 0x00000000 /* EBC Selection */
-
-#define SDR0_USB2D0CR_USB_DEV_INT_SEL_MASK 0x00000002 /* USB Device Interface
- Selection */
-#define SDR0_USB2D0CR_USB20D_DEVSEL 0x00000000 /* USB2.0 Device Selected */
-#define SDR0_USB2D0CR_USB11D_DEVSEL 0x00000002 /* USB1.1 Device Selected */
-
-#define SDR0_USB2D0CR_LEEN_MASK 0x00000001 /* Little Endian selection */
-#define SDR0_USB2D0CR_LEEN_DISABLE 0x00000000 /* Little Endian Disable */
-#define SDR0_USB2D0CR_LEEN_ENABLE 0x00000001 /* Little Endian Enable */
-
- /* USB2 Host Control Register */
-#define SDR0_USB2H0CR 0x0340
-#define SDR0_USB2H0CR_WDINT_MASK 0x00000001 /* Host UTMI Word Interface*/
-#define SDR0_USB2H0CR_WDINT_8BIT_60MHZ 0x00000000 /* 8-bit/60MHz */
-#define SDR0_USB2H0CR_WDINT_16BIT_30MHZ 0x00000001 /* 16-bit/30MHz */
-#define SDR0_USB2H0CR_EFLADJ_MASK 0x0000007e /* EHCI Frame Length
- Adjustment */
-
- /* Pin Function Control Register 1 */
-#define SDR0_PFC1 0x4101
-#define SDR0_PFC1_U1ME_MASK 0x02000000 /* UART1 Mode Enable */
-#define SDR0_PFC1_U1ME_DSR_DTR 0x00000000 /* UART1 in DSR/DTR Mode */
-#define SDR0_PFC1_U1ME_CTS_RTS 0x02000000 /* UART1 in CTS/RTS Mode */
-
-#define SDR0_PFC1_SELECT_MASK 0x01C00000 /* Ethernet Pin Select
- EMAC 0 */
-#define SDR0_PFC1_SELECT_CONFIG_1_1 0x00C00000 /* 1xMII using RGMII
- bridge */
-#define SDR0_PFC1_SELECT_CONFIG_1_2 0x00000000 /* 1xMII using ZMII
- bridge */
-#define SDR0_PFC1_SELECT_CONFIG_2 0x00C00000 /* 1xGMII using RGMII
- bridge */
-#define SDR0_PFC1_SELECT_CONFIG_3 0x01000000 /* 1xTBI using RGMII
- bridge */
-#define SDR0_PFC1_SELECT_CONFIG_4 0x01400000 /* 2xRGMII using RGMII
- bridge */
-#define SDR0_PFC1_SELECT_CONFIG_5 0x01800000 /* 2xRTBI using RGMII
- bridge */
-#define SDR0_PFC1_SELECT_CONFIG_6 0x00800000 /* 2xSMII using ZMII
- bridge */
-
-#define SDR0_PFC1_U0ME_MASK 0x00080000 /* UART0 Mode Enable */
-#define SDR0_PFC1_U0ME_DSR_DTR 0x00000000 /* UART0 in DSR/DTR Mode */
-#define SDR0_PFC1_U0ME_CTS_RTS 0x00080000 /* UART0 in CTS/RTS Mode */
-#define SDR0_PFC1_U0IM_MASK 0x00040000 /* UART0 Interface Mode */
-#define SDR0_PFC1_U0IM_8PINS 0x00000000 /* UART0 Interface Mode 8 pins */
-#define SDR0_PFC1_U0IM_4PINS 0x00040000 /* UART0 Interface Mode 4 pins */
-#define SDR0_PFC1_SIS_MASK 0x00020000 /* SCP or IIC1 Selection */
-#define SDR0_PFC1_SIS_SCP_SEL 0x00000000 /* SCP Selected */
-#define SDR0_PFC1_SIS_IIC1_SEL 0x00020000 /* IIC1 Selected */
-#define SDR0_PFC1_UES_MASK 0x00010000 /* USB2D_RX_Active / EBC_Hold Req
- Selection */
-#define SDR0_PFC1_UES_USB2D_SEL 0x00000000 /* USB2D_RX_Active Selected */
-#define SDR0_PFC1_UES_EBCHR_SEL 0x00010000 /* EBC_Hold Req Selected */
-#define SDR0_PFC1_DIS_MASK 0x00008000 /* DMA_Req(1) / UIC_IRQ(5)
- Selection */
-#define SDR0_PFC1_DIS_DMAR_SEL 0x00000000 /* DMA_Req(1) Selected */
-#define SDR0_PFC1_DIS_UICIRQ5_SEL 0x00008000 /* UIC_IRQ(5) Selected */
-#define SDR0_PFC1_ERE_MASK 0x00004000 /* EBC Mast.Ext.Req.En./GPIO0(27)
- Selection */
-#define SDR0_PFC1_ERE_EXTR_SEL 0x00000000 /* EBC Mast.Ext.Req.En. Selected */
-#define SDR0_PFC1_ERE_GPIO0_27_SEL 0x00004000 /* GPIO0(27) Selected */
-#define SDR0_PFC1_UPR_MASK 0x00002000 /* USB2 Device Packet Reject
- Selection */
-#define SDR0_PFC1_UPR_DISABLE 0x00000000 /* USB2 Device Packet Reject
- Disable */
-#define SDR0_PFC1_UPR_ENABLE 0x00002000 /* USB2 Device Packet Reject
- Enable */
-
-#define SDR0_PFC1_PLB_PME_MASK 0x00001000
- /* PLB3/PLB4 Perf. Monitor En. Selection */
-#define SDR0_PFC1_PLB_PME_PLB3_SEL 0x00000000
- /* PLB3 Performance Monitor Enable */
-#define SDR0_PFC1_PLB_PME_PLB4_SEL 0x00001000
- /* PLB3 Performance Monitor Enable */
-#define SDR0_PFC1_GFGGI_MASK 0x0000000F /* GPT Frequency Generation
- Gated In */
-
- /* Ethernet PLL Configuration Register */
-#define SDR0_PFC2 0x4102
-#define SDR0_PFC2_TUNE_MASK 0x01FF8000 /* Loop stability tuning bits */
-#define SDR0_PFC2_MULTI_MASK 0x00007C00 /* Frequency multiplication
- selector */
-#define SDR0_PFC2_RANGEB_MASK 0x00000380 /* PLLOUTB/C frequency selector */
-#define SDR0_PFC2_RANGEA_MASK 0x00000071 /* PLLOUTA frequency selector */
-
-#define SDR0_PFC2_SELECT_MASK 0xE0000000 /* Ethernet Pin select EMAC1 */
-#define SDR0_PFC2_SELECT_CONFIG_1_1 0x60000000 /* 1xMII using RGMII bridge */
-#define SDR0_PFC2_SELECT_CONFIG_1_2 0x00000000 /* 1xMII using ZMII bridge */
-#define SDR0_PFC2_SELECT_CONFIG_2 0x60000000 /* 1xGMII using RGMII bridge */
-#define SDR0_PFC2_SELECT_CONFIG_3 0x80000000 /* 1xTBI using RGMII bridge */
-#define SDR0_PFC2_SELECT_CONFIG_4 0xA0000000 /* 2xRGMII using RGMII bridge */
-#define SDR0_PFC2_SELECT_CONFIG_5 0xC0000000 /* 2xRTBI using RGMII bridge */
-#define SDR0_PFC2_SELECT_CONFIG_6 0x40000000 /* 2xSMII using ZMII bridge */
-
-#define SDR0_PFC4 0x4104
-
- /* USB2PHY0 Control Register */
-#define SDR0_USB2PHY0CR 0x4103
-#define SDR0_USB2PHY0CR_UTMICN_MASK 0x00100000
-
- /* PHY UTMI interface connection */
-#define SDR0_USB2PHY0CR_UTMICN_DEV 0x00000000 /* Device support */
-#define SDR0_USB2PHY0CR_UTMICN_HOST 0x00100000 /* Host support */
-
-#define SDR0_USB2PHY0CR_DWNSTR_MASK 0x00400000 /* Select downstream port mode */
-#define SDR0_USB2PHY0CR_DWNSTR_DEV 0x00000000 /* Device */
-#define SDR0_USB2PHY0CR_DWNSTR_HOST 0x00400000 /* Host */
-
-#define SDR0_USB2PHY0CR_DVBUS_MASK 0x00800000
- /* VBus detect (Device mode only) */
-#define SDR0_USB2PHY0CR_DVBUS_PURDIS 0x00000000
- /* Pull-up resistance on D+ is disabled */
-#define SDR0_USB2PHY0CR_DVBUS_PUREN 0x00800000
- /* Pull-up resistance on D+ is enabled */
-
-#define SDR0_USB2PHY0CR_WDINT_MASK 0x01000000
- /* PHY UTMI data width and clock select */
-#define SDR0_USB2PHY0CR_WDINT_8BIT_60MHZ 0x00000000 /* 8-bit data/60MHz */
-#define SDR0_USB2PHY0CR_WDINT_16BIT_30MHZ 0x01000000 /* 16-bit data/30MHz */
-
-#define SDR0_USB2PHY0CR_LOOPEN_MASK 0x02000000 /* Loop back test enable */
-#define SDR0_USB2PHY0CR_LOOP_ENABLE 0x00000000 /* Loop back disabled */
-#define SDR0_USB2PHY0CR_LOOP_DISABLE 0x02000000
- /* Loop back enabled (only test purposes) */
-
-#define SDR0_USB2PHY0CR_XOON_MASK 0x04000000
- /* Force XO block on during a suspend */
-#define SDR0_USB2PHY0CR_XO_ON 0x00000000 /* PHY XO block is powered-on */
-#define SDR0_USB2PHY0CR_XO_OFF 0x04000000
- /* PHY XO block is powered-off when all ports are suspended */
-
-#define SDR0_USB2PHY0CR_PWRSAV_MASK 0x08000000 /* Select PHY power-save mode */
-#define SDR0_USB2PHY0CR_PWRSAV_OFF 0x00000000 /* Non-power-save mode */
-#define SDR0_USB2PHY0CR_PWRSAV_ON 0x08000000 /* Power-save mode. Valid only
- for full-speed operation */
-
-#define SDR0_USB2PHY0CR_XOREF_MASK 0x10000000 /* Select reference clock
- source */
-#define SDR0_USB2PHY0CR_XOREF_INTERNAL 0x00000000 /* PHY PLL uses chip internal
- 48M clock as a reference */
-#define SDR0_USB2PHY0CR_XOREF_XO 0x10000000 /* PHY PLL uses internal XO
- block output as a reference */
-
-#define SDR0_USB2PHY0CR_XOCLK_MASK 0x20000000 /* Select clock for XO
- block*/
-#define SDR0_USB2PHY0CR_XOCLK_EXTERNAL 0x00000000 /* PHY macro used an external
- clock */
-#define SDR0_USB2PHY0CR_XOCLK_CRYSTAL 0x20000000 /* PHY macro uses the clock
- from a crystal */
-
-#define SDR0_USB2PHY0CR_CLKSEL_MASK 0xc0000000 /* Select ref clk freq */
-#define SDR0_USB2PHY0CR_CLKSEL_12MHZ 0x00000000 /* Select ref clk freq
- = 12 MHz */
-#define SDR0_USB2PHY0CR_CLKSEL_48MHZ 0x40000000 /* Select ref clk freq
- = 48 MHz */
-#define SDR0_USB2PHY0CR_CLKSEL_24MHZ 0x80000000 /* Select ref clk freq
- = 24 MHz */
-
- /* Miscealleneaous Function Reg. */
-#define SDR0_MFR 0x4300
-#define SDR0_MFR_ETH0_CLK_SEL_MASK 0x08000000 /* Ethernet0 Clock Select */
-#define SDR0_MFR_ETH0_CLK_SEL_EXT 0x00000000
-#define SDR0_MFR_ETH1_CLK_SEL_MASK 0x04000000 /* Ethernet1 Clock Select */
-#define SDR0_MFR_ETH1_CLK_SEL_EXT 0x00000000
-#define SDR0_MFR_ZMII_MODE_MASK 0x03000000 /* ZMII Mode Mask */
-#define SDR0_MFR_ZMII_MODE_MII 0x00000000 /* ZMII Mode MII */
-#define SDR0_MFR_ZMII_MODE_SMII 0x01000000 /* ZMII Mode SMII */
-#define SDR0_MFR_ZMII_MODE_BIT0 0x02000000 /* ZMII Mode Bit0 */
-#define SDR0_MFR_ZMII_MODE_BIT1 0x01000000 /* ZMII Mode Bit1 */
-#define SDR0_MFR_ZM_ENCODE(n) ((((unsigned long)(n))&0x3)<<24)
-#define SDR0_MFR_ZM_DECODE(n) ((((unsigned long)(n))<<24)&0x3)
-
-#define SDR0_MFR_ERRATA3_EN0 0x00800000
-#define SDR0_MFR_ERRATA3_EN1 0x00400000
-#define SDR0_MFR_PKT_REJ_MASK 0x00180000 /* Pkt Rej. Enable Mask */
-#define SDR0_MFR_PKT_REJ_EN 0x00180000 /* Pkt Rej. Ena. on both EMAC3 0-1 */
-#define SDR0_MFR_PKT_REJ_EN0 0x00100000 /* Pkt Rej. Enable on EMAC3(0) */
-#define SDR0_MFR_PKT_REJ_EN1 0x00080000 /* Pkt Rej. Enable on EMAC3(1) */
-#define SDR0_MFR_PKT_REJ_POL 0x00200000 /* Packet Reject Polarity */
-
-#endif /* defined(CONFIG_440EPX) || defined(CONFIG_440GRX) */
-
- /* CUST1 Customer Configuration Register1 */
-#define SDR0_CUST1 0x4002
-#define SDR0_CUST1_NDRSC_MASK 0xFFFF0000 /* NDRSC Device Read Count */
-#define SDR0_CUST1_NDRSC_ENCODE(n) ((((unsigned long)(n))&0xFFFF)<<16)
-#define SDR0_CUST1_NDRSC_DECODE(n) ((((unsigned long)(n))>>16)&0xFFFF)
-
- /* Pin Function Control Register 0 */
-#define SDR0_PFC0 0x4100
-#define SDR0_PFC0_CPU_TR_EN_MASK 0x00000100 /* CPU Trace Enable Mask */
-#define SDR0_PFC0_CPU_TRACE_EN 0x00000100 /* CPU Trace Enable */
-#define SDR0_PFC0_CPU_TRACE_DIS 0x00000100 /* CPU Trace Disable */
-#define SDR0_PFC0_CTE_ENCODE(n) ((((unsigned long)(n))&0x01)<<8)
-#define SDR0_PFC0_CTE_DECODE(n) ((((unsigned long)(n))>>8)&0x01)
-
- /* Pin Function Control Register 1 */
-#define SDR0_PFC1 0x4101
-#define SDR0_PFC1_U1ME_MASK 0x02000000 /* UART1 Mode Enable */
-#define SDR0_PFC1_U1ME_DSR_DTR 0x00000000 /* UART1 in DSR/DTR Mode */
-#define SDR0_PFC1_U1ME_CTS_RTS 0x02000000 /* UART1 in CTS/RTS Mode */
-#define SDR0_PFC1_U0ME_MASK 0x00080000 /* UART0 Mode Enable */
-#define SDR0_PFC1_U0ME_DSR_DTR 0x00000000 /* UART0 in DSR/DTR Mode */
-#define SDR0_PFC1_U0ME_CTS_RTS 0x00080000 /* UART0 in CTS/RTS Mode */
-#define SDR0_PFC1_U0IM_MASK 0x00040000 /* UART0 Interface Mode */
-#define SDR0_PFC1_U0IM_8PINS 0x00000000 /* UART0 Interface Mode 8 pins */
-#define SDR0_PFC1_U0IM_4PINS 0x00040000 /* UART0 Interface Mode 4 pins */
-#define SDR0_PFC1_SIS_MASK 0x00020000 /* SCP or IIC1 Selection */
-#define SDR0_PFC1_SIS_SCP_SEL 0x00000000 /* SCP Selected */
-#define SDR0_PFC1_SIS_IIC1_SEL 0x00020000 /* IIC1 Selected */
-#define SDR0_PFC1_UES_MASK 0x00010000 /* USB2D_RX_Active / EBC_Hold Req
- Selection */
-#define SDR0_PFC1_UES_USB2D_SEL 0x00000000 /* USB2D_RX_Active Selected */
-#define SDR0_PFC1_UES_EBCHR_SEL 0x00010000 /* EBC_Hold Req Selected */
-#define SDR0_PFC1_DIS_MASK 0x00008000 /* DMA_Req(1) / UIC_IRQ(5)
- Selection */
-#define SDR0_PFC1_DIS_DMAR_SEL 0x00000000 /* DMA_Req(1) Selected */
-#define SDR0_PFC1_DIS_UICIRQ5_SEL 0x00008000 /* UIC_IRQ(5) Selected */
-#define SDR0_PFC1_ERE_MASK 0x00004000 /* EBC Mast.Ext.Req.En./GPIO0(27)
- Selection */
-#define SDR0_PFC1_ERE_EXTR_SEL 0x00000000 /* EBC Mast.Ext.Req.En. Selected */
-#define SDR0_PFC1_ERE_GPIO0_27_SEL 0x00004000 /* GPIO0(27) Selected */
-#define SDR0_PFC1_UPR_MASK 0x00002000 /* USB2 Device Packet Reject
- Selection */
-#define SDR0_PFC1_UPR_DISABLE 0x00000000 /* USB2 Device Packet Reject
- Disable */
-#define SDR0_PFC1_UPR_ENABLE 0x00002000 /* USB2 Device Packet Reject
- Enable */
-
-#define SDR0_PFC1_PLB_PME_MASK 0x00001000 /* PLB3/PLB4 Perf. Monitor En.
- Selection */
-#define SDR0_PFC1_PLB_PME_PLB3_SEL 0x00000000 /* PLB3 Performance Monitor
- Enable */
-#define SDR0_PFC1_PLB_PME_PLB4_SEL 0x00001000 /* PLB3 Performance Monitor
- Enable */
-#define SDR0_PFC1_GFGGI_MASK 0x0000000F /* GPT Frequency Generation
- Gated In */
-
-#endif /* 440EP || 440GR || 440EPX || 440GRX */
-
-#if defined(CONFIG_440EP) || defined(CONFIG_440GR) || \
- defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \
- defined(CONFIG_460EX) || defined(CONFIG_460GT)
- /* CUST0 Customer Configuration Register0 */
-#define SDR0_CUST0 0x4000
-#define SDR0_CUST0_MUX_E_N_G_MASK 0xC0000000 /* Mux_Emac_NDFC_GPIO */
-#define SDR0_CUST0_MUX_EMAC_SEL 0x40000000 /* Emac Selection */
-#define SDR0_CUST0_MUX_NDFC_SEL 0x80000000 /* NDFC Selection */
-#define SDR0_CUST0_MUX_GPIO_SEL 0xC0000000 /* GPIO Selection */
-
-#define SDR0_CUST0_NDFC_EN_MASK 0x20000000 /* NDFC Enable Mask */
-#define SDR0_CUST0_NDFC_ENABLE 0x20000000 /* NDFC Enable */
-#define SDR0_CUST0_NDFC_DISABLE 0x00000000 /* NDFC Disable */
-
-#define SDR0_CUST0_NDFC_BW_MASK 0x10000000 /* NDFC Boot Width */
-#define SDR0_CUST0_NDFC_BW_16_BIT 0x10000000 /* NDFC Boot Width = 16 Bit */
-#define SDR0_CUST0_NDFC_BW_8_BIT 0x00000000 /* NDFC Boot Width = 8 Bit */
-
-#define SDR0_CUST0_NDFC_BP_MASK 0x0F000000 /* NDFC Boot Page */
-#define SDR0_CUST0_NDFC_BP_ENCODE(n) ((((unsigned long)(n))&0xF)<<24)
-#define SDR0_CUST0_NDFC_BP_DECODE(n) ((((unsigned long)(n))>>24)&0x0F)
-
-#define SDR0_CUST0_NDFC_BAC_MASK 0x00C00000 /* NDFC Boot Address Cycle */
-#define SDR0_CUST0_NDFC_BAC_ENCODE(n) ((((unsigned long)(n))&0x3)<<22)
-#define SDR0_CUST0_NDFC_BAC_DECODE(n) ((((unsigned long)(n))>>22)&0x03)
-
-#define SDR0_CUST0_NDFC_ARE_MASK 0x00200000 /* NDFC Auto Read Enable */
-#define SDR0_CUST0_NDFC_ARE_ENABLE 0x00200000 /* NDFC Auto Read Enable */
-#define SDR0_CUST0_NDFC_ARE_DISABLE 0x00000000 /* NDFC Auto Read Disable */
-
-#define SDR0_CUST0_NRB_MASK 0x00100000 /* NDFC Ready / Busy */
-#define SDR0_CUST0_NRB_BUSY 0x00100000 /* Busy */
-#define SDR0_CUST0_NRB_READY 0x00000000 /* Ready */
-
-#define SDR0_CUST0_NDRSC_MASK 0x0000FFF0 /* NDFC Device Reset Count Mask */
-#define SDR0_CUST0_NDRSC_ENCODE(n) ((((unsigned long)(n))&0xFFF)<<4)
-#define SDR0_CUST0_NDRSC_DECODE(n) ((((unsigned long)(n))>>4)&0xFFF)
-
-#define SDR0_CUST0_CHIPSELGAT_MASK 0x0000000F /* Chip Select Gating Mask */
-#define SDR0_CUST0_CHIPSELGAT_DIS 0x00000000 /* Chip Select Gating Disable */
-#define SDR0_CUST0_CHIPSELGAT_ENALL 0x0000000F /*All Chip Select Gating Enable*/
-#define SDR0_CUST0_CHIPSELGAT_EN0 0x00000008 /* Chip Select0 Gating Enable */
-#define SDR0_CUST0_CHIPSELGAT_EN1 0x00000004 /* Chip Select1 Gating Enable */
-#define SDR0_CUST0_CHIPSELGAT_EN2 0x00000002 /* Chip Select2 Gating Enable */
-#define SDR0_CUST0_CHIPSELGAT_EN3 0x00000001 /* Chip Select3 Gating Enable */
-#endif
-
-/*-----------------------------------------------------------------------------
- | On-Chip Buses
- +----------------------------------------------------------------------------*/
-/* TODO: as needed */
-
-/*-----------------------------------------------------------------------------
- | Clocking, Power Management and Chip Control
- +----------------------------------------------------------------------------*/
-#if defined(CONFIG_460EX) || defined(CONFIG_460GT) || \
- defined(CONFIG_460SX)
-#define CNTRL_DCR_BASE 0x160
-#else
-#define CNTRL_DCR_BASE 0x0b0
-#endif
-
-#define CPC0_SYS0 (CNTRL_DCR_BASE+0x30) /* System configuration reg 0 */
-#define CPC0_SYS1 (CNTRL_DCR_BASE+0x31) /* System configuration reg 1 */
-
-#define CPC0_STRP0 (CNTRL_DCR_BASE+0x34) /* Power-on config reg 0 (RO) */
-#define CPC0_STRP1 (CNTRL_DCR_BASE+0x35) /* Power-on config reg 1 (RO) */
-
-#define CPC0_GPIO (CNTRL_DCR_BASE+0x38) /* GPIO config reg (440GP) */
-
-#define CPC0_CR0 (CNTRL_DCR_BASE+0x3b) /* Control 0 register */
-#define CPC0_CR1 (CNTRL_DCR_BASE+0x3a) /* Control 1 register */
-
-/*-----------------------------------------------------------------------------
- | DMA
- +----------------------------------------------------------------------------*/
-#if defined(CONFIG_460EX) || defined(CONFIG_460GT)
-#define DMA_DCR_BASE 0x200
-#else
-#define DMA_DCR_BASE 0x100
-#endif
-#define DMACR0 (DMA_DCR_BASE+0x00) /* DMA channel control register 0 */
-#define DMACT0 (DMA_DCR_BASE+0x01) /* DMA count register 0 */
-#define DMACR1 (DMA_DCR_BASE+0x08) /* DMA channel control register 1 */
-#define DMACT1 (DMA_DCR_BASE+0x09) /* DMA count register 1 */
-#define DMACR2 (DMA_DCR_BASE+0x10) /* DMA channel control register 2 */
-#define DMACT2 (DMA_DCR_BASE+0x11) /* DMA count register 2 */
-#define DMACR3 (DMA_DCR_BASE+0x18) /* DMA channel control register 2 */
-#define DMASR (DMA_DCR_BASE+0x20) /* DMA status register */
-#define DMASGC (DMA_DCR_BASE+0x23) /* DMA scatter/gather command register */
-
-/*-----------------------------------------------------------------------------
- | Memory Access Layer
- +----------------------------------------------------------------------------*/
-#define MAL_DCR_BASE 0x180
-#define MAL0_CFG (MAL_DCR_BASE + 0x00) /* MAL Config reg */
-#define MAL0_ESR (MAL_DCR_BASE + 0x01) /* Error Status (Read/Clear) */
-#define MAL0_IER (MAL_DCR_BASE + 0x02) /* Interrupt enable */
-#define MAL0_TXCASR (MAL_DCR_BASE + 0x04) /* TX Channel active (set) */
-#define MAL0_TXCARR (MAL_DCR_BASE + 0x05) /* TX Channel active (reset) */
-#define MAL0_TXEOBISR (MAL_DCR_BASE + 0x06) /* TX End of buffer int status*/
-#define MAL0_TXDEIR (MAL_DCR_BASE + 0x07) /* TX Descr. Error Int */
-#define MAL0_TXBADDR (MAL_DCR_BASE + 0x09) /* TX descriptor base addr*/
-#define MAL0_RXCASR (MAL_DCR_BASE + 0x10) /* RX Channel active (set) */
-#define MAL0_RXCARR (MAL_DCR_BASE + 0x11) /* RX Channel active (reset) */
-#define MAL0_RXEOBISR (MAL_DCR_BASE + 0x12) /* RX End of buffer int status*/
-#define MAL0_RXDEIR (MAL_DCR_BASE + 0x13) /* RX Descr. Error Int */
-#define MAL0_RXBADDR (MAL_DCR_BASE + 0x15) /* RX descriptor base addr */
-#define MAL0_TXCTP0R (MAL_DCR_BASE + 0x20) /* TX 0 Channel table pointer */
-#define MAL0_TXCTP1R (MAL_DCR_BASE + 0x21) /* TX 1 Channel table pointer */
-#define MAL0_TXCTP2R (MAL_DCR_BASE + 0x22) /* TX 2 Channel table pointer */
-#define MAL0_TXCTP3R (MAL_DCR_BASE + 0x23) /* TX 3 Channel table pointer */
-#define MAL0_RXCTP0R (MAL_DCR_BASE + 0x40) /* RX 0 Channel table pointer */
-#define MAL0_RXCTP1R (MAL_DCR_BASE + 0x41) /* RX 1 Channel table pointer */
-#define MAL0_RCBS0 (MAL_DCR_BASE + 0x60) /* RX 0 Channel buffer size */
-#define MAL0_RCBS1 (MAL_DCR_BASE + 0x61) /* RX 1 Channel buffer size */
-#if defined(CONFIG_440GX) || \
- defined(CONFIG_460EX) || defined(CONFIG_460GT)
-#define MAL0_RXCTP2R (MAL_DCR_BASE + 0x42) /* RX 2 Channel table pointer */
-#define MAL0_RXCTP3R (MAL_DCR_BASE + 0x43) /* RX 3 Channel table pointer */
-#define MAL0_RXCTP8R (MAL_DCR_BASE + 0x48) /* RX 8 Channel table pointer */
-#define MAL0_RXCTP16R (MAL_DCR_BASE + 0x50) /* RX 16 Channel table pointer*/
-#define MAL0_RXCTP24R (MAL_DCR_BASE + 0x58) /* RX 24 Channel table pointer*/
-#define MAL0_RCBS2 (MAL_DCR_BASE + 0x62) /* RX 2 Channel buffer size */
-#define MAL0_RCBS3 (MAL_DCR_BASE + 0x63) /* RX 3 Channel buffer size */
-#define MAL0_RCBS8 (MAL_DCR_BASE + 0x68) /* RX 8 Channel buffer size */
-#define MAL0_RCBS16 (MAL_DCR_BASE + 0x70) /* RX 16 Channel buffer size */
-#define MAL0_RCBS24 (MAL_DCR_BASE + 0x78) /* RX 24 Channel buffer size */
-#endif /* CONFIG_440GX */
-
-/*-----------------------------------------------------------------------------+
-| SDR0 Bit Settings
-+-----------------------------------------------------------------------------*/
-#if defined(CONFIG_440SP)
-#define SDR0_DDR0 0x00E1
-#define SDR0_DDR0_DPLLRST 0x80000000
-#define SDR0_DDR0_DDRM_MASK 0x60000000
-#define SDR0_DDR0_DDRM_DDR1 0x20000000
-#define SDR0_DDR0_DDRM_DDR2 0x40000000
-#define SDR0_DDR0_DDRM_ENCODE(n) ((((unsigned long)(n))&0x03)<<29)
-#define SDR0_DDR0_DDRM_DECODE(n) ((((unsigned long)(n))>>29)&0x03)
-#define SDR0_DDR0_TUNE_ENCODE(n) ((((unsigned long)(n))&0x2FF)<<0)
-#define SDR0_DDR0_TUNE_DECODE(n) ((((unsigned long)(n))>>0)&0x2FF)
-#endif
-
-#if defined(CONFIG_440SPE) || defined(CONFIG_460SX)
-#define SDR0_CP440 0x0180
-#define SDR0_CP440_ERPN_MASK 0x30000000
-#define SDR0_CP440_ERPN_MASK_HI 0x3000
-#define SDR0_CP440_ERPN_MASK_LO 0x0000
-#define SDR0_CP440_ERPN_EBC 0x10000000
-#define SDR0_CP440_ERPN_EBC_HI 0x1000
-#define SDR0_CP440_ERPN_EBC_LO 0x0000
-#define SDR0_CP440_ERPN_PCI 0x20000000
-#define SDR0_CP440_ERPN_PCI_HI 0x2000
-#define SDR0_CP440_ERPN_PCI_LO 0x0000
-#define SDR0_CP440_ERPN_ENCODE(n) ((((unsigned long)(n))&0x03)<<28)
-#define SDR0_CP440_ERPN_DECODE(n) ((((unsigned long)(n))>>28)&0x03)
-#define SDR0_CP440_NTO1_MASK 0x00000002
-#define SDR0_CP440_NTO1_NTOP 0x00000000
-#define SDR0_CP440_NTO1_NTO1 0x00000002
-#define SDR0_CP440_NTO1_ENCODE(n) ((((unsigned long)(n))&0x01)<<1)
-#define SDR0_CP440_NTO1_DECODE(n) ((((unsigned long)(n))>>1)&0x01)
-
-#define SDR0_SDSTP0 0x0020
-#define SDR0_SDSTP0_ENG_MASK 0x80000000
-#define SDR0_SDSTP0_ENG_PLLDIS 0x00000000
-#define SDR0_SDSTP0_ENG_PLLENAB 0x80000000
-#define SDR0_SDSTP0_ENG_ENCODE(n) ((((unsigned long)(n))&0x01)<<31)
-#define SDR0_SDSTP0_ENG_DECODE(n) ((((unsigned long)(n))>>31)&0x01)
-#define SDR0_SDSTP0_SRC_MASK 0x40000000
-#define SDR0_SDSTP0_SRC_PLLOUTA 0x00000000
-#define SDR0_SDSTP0_SRC_PLLOUTB 0x40000000
-#define SDR0_SDSTP0_SRC_ENCODE(n) ((((unsigned long)(n))&0x01)<<30)
-#define SDR0_SDSTP0_SRC_DECODE(n) ((((unsigned long)(n))>>30)&0x01)
-#define SDR0_SDSTP0_SEL_MASK 0x38000000
-#define SDR0_SDSTP0_SEL_PLLOUT 0x00000000
-#define SDR0_SDSTP0_SEL_CPU 0x08000000
-#define SDR0_SDSTP0_SEL_EBC 0x28000000
-#define SDR0_SDSTP0_SEL_ENCODE(n) ((((unsigned long)(n))&0x07)<<27)
-#define SDR0_SDSTP0_SEL_DECODE(n) ((((unsigned long)(n))>>27)&0x07)
-#define SDR0_SDSTP0_TUNE_MASK 0x07FE0000
-#define SDR0_SDSTP0_TUNE_ENCODE(n) ((((unsigned long)(n))&0x3FF)<<17)
-#define SDR0_SDSTP0_TUNE_DECODE(n) ((((unsigned long)(n))>>17)&0x3FF)
-#define SDR0_SDSTP0_FBDV_MASK 0x0001F000
-#define SDR0_SDSTP0_FBDV_ENCODE(n) ((((unsigned long)(n))&0x1F)<<12)
-#define SDR0_SDSTP0_FBDV_DECODE(n) ((((((unsigned long)(n))>>12)-1)&0x1F)+1)
-#define SDR0_SDSTP0_FWDVA_MASK 0x00000F00
-#define SDR0_SDSTP0_FWDVA_ENCODE(n) ((((unsigned long)(n))&0x0F)<<8)
-#define SDR0_SDSTP0_FWDVA_DECODE(n) ((((((unsigned long)(n))>>8)-1)&0x0F)+1)
-#define SDR0_SDSTP0_FWDVB_MASK 0x000000E0
-#define SDR0_SDSTP0_FWDVB_ENCODE(n) ((((unsigned long)(n))&0x07)<<5)
-#define SDR0_SDSTP0_FWDVB_DECODE(n) ((((((unsigned long)(n))>>5)-1)&0x07)+1)
-#define SDR0_SDSTP0_PRBDV0_MASK 0x0000001C
-#define SDR0_SDSTP0_PRBDV0_ENCODE(n) ((((unsigned long)(n))&0x07)<<2)
-#define SDR0_SDSTP0_PRBDV0_DECODE(n) ((((((unsigned long)(n))>>2)-1)&0x07)+1)
-#define SDR0_SDSTP0_OPBDV0_MASK 0x00000003
-#define SDR0_SDSTP0_OPBDV0_ENCODE(n) ((((unsigned long)(n))&0x03)<<0)
-#define SDR0_SDSTP0_OPBDV0_DECODE(n) ((((((unsigned long)(n))>>0)-1)&0x03)+1)
-
-
-#define SDR0_SDSTP1 0x0021
-#define SDR0_SDSTP1_LFBDV_MASK 0xFC000000
-#define SDR0_SDSTP1_LFBDV_ENCODE(n) ((((unsigned long)(n))&0x3F)<<26)
-#define SDR0_SDSTP1_LFBDV_DECODE(n) ((((unsigned long)(n))>>26)&0x3F)
-#define SDR0_SDSTP1_PERDV0_MASK 0x03000000
-#define SDR0_SDSTP1_PERDV0_ENCODE(n) ((((unsigned long)(n))&0x03)<<24)
-#define SDR0_SDSTP1_PERDV0_DECODE(n) ((((unsigned long)(n))>>24)&0x03)
-#define SDR0_SDSTP1_MALDV0_MASK 0x00C00000
-#define SDR0_SDSTP1_MALDV0_ENCODE(n) ((((unsigned long)(n))&0x03)<<22)
-#define SDR0_SDSTP1_MALDV0_DECODE(n) ((((unsigned long)(n))>>22)&0x03)
-#define SDR0_SDSTP1_DDR_MODE_MASK 0x00300000
-#define SDR0_SDSTP1_DDR1_MODE 0x00100000
-#define SDR0_SDSTP1_DDR2_MODE 0x00200000
-#define SDR0_SDSTP1_DDR_ENCODE(n) ((((unsigned long)(n))&0x03)<<20)
-#define SDR0_SDSTP1_DDR_DECODE(n) ((((unsigned long)(n))>>20)&0x03)
-#define SDR0_SDSTP1_ERPN_MASK 0x00080000
-#define SDR0_SDSTP1_ERPN_EBC 0x00000000
-#define SDR0_SDSTP1_ERPN_PCI 0x00080000
-#define SDR0_SDSTP1_PAE_MASK 0x00040000
-#define SDR0_SDSTP1_PAE_DISABLE 0x00000000
-#define SDR0_SDSTP1_PAE_ENABLE 0x00040000
-#define SDR0_SDSTP1_PAE_ENCODE(n) ((((unsigned long)(n))&0x01)<<18)
-#define SDR0_SDSTP1_PAE_DECODE(n) ((((unsigned long)(n))>>18)&0x01)
-#define SDR0_SDSTP1_PHCE_MASK 0x00020000
-#define SDR0_SDSTP1_PHCE_DISABLE 0x00000000
-#define SDR0_SDSTP1_PHCE_ENABLE 0x00020000
-#define SDR0_SDSTP1_PHCE_ENCODE(n) ((((unsigned long)(n))&0x01)<<17)
-#define SDR0_SDSTP1_PHCE_DECODE(n) ((((unsigned long)(n))>>17)&0x01)
-#define SDR0_SDSTP1_PISE_MASK 0x00010000
-#define SDR0_SDSTP1_PISE_DISABLE 0x00000000
-#define SDR0_SDSTP1_PISE_ENABLE 0x00001000
-#define SDR0_SDSTP1_PISE_ENCODE(n) ((((unsigned long)(n))&0x01)<<16)
-#define SDR0_SDSTP1_PISE_DECODE(n) ((((unsigned long)(n))>>16)&0x01)
-#define SDR0_SDSTP1_PCWE_MASK 0x00008000
-#define SDR0_SDSTP1_PCWE_DISABLE 0x00000000
-#define SDR0_SDSTP1_PCWE_ENABLE 0x00008000
-#define SDR0_SDSTP1_PCWE_ENCODE(n) ((((unsigned long)(n))&0x01)<<15)
-#define SDR0_SDSTP1_PCWE_DECODE(n) ((((unsigned long)(n))>>15)&0x01)
-#define SDR0_SDSTP1_PPIM_MASK 0x00007800
-#define SDR0_SDSTP1_PPIM_ENCODE(n) ((((unsigned long)(n))&0x0F)<<11)
-#define SDR0_SDSTP1_PPIM_DECODE(n) ((((unsigned long)(n))>>11)&0x0F)
-#define SDR0_SDSTP1_PR64E_MASK 0x00000400
-#define SDR0_SDSTP1_PR64E_DISABLE 0x00000000
-#define SDR0_SDSTP1_PR64E_ENABLE 0x00000400
-#define SDR0_SDSTP1_PR64E_ENCODE(n) ((((unsigned long)(n))&0x01)<<10)
-#define SDR0_SDSTP1_PR64E_DECODE(n) ((((unsigned long)(n))>>10)&0x01)
-#define SDR0_SDSTP1_PXFS_MASK 0x00000300
-#define SDR0_SDSTP1_PXFS_100_133 0x00000000
-#define SDR0_SDSTP1_PXFS_66_100 0x00000100
-#define SDR0_SDSTP1_PXFS_50_66 0x00000200
-#define SDR0_SDSTP1_PXFS_0_50 0x00000300
-#define SDR0_SDSTP1_PXFS_ENCODE(n) ((((unsigned long)(n))&0x03)<<8)
-#define SDR0_SDSTP1_PXFS_DECODE(n) ((((unsigned long)(n))>>8)&0x03)
-#define SDR0_SDSTP1_EBCW_MASK 0x00000080 /* SOP */
-#define SDR0_SDSTP1_EBCW_8_BITS 0x00000000 /* SOP */
-#define SDR0_SDSTP1_EBCW_16_BITS 0x00000080 /* SOP */
-#define SDR0_SDSTP1_DBGEN_MASK 0x00000030 /* $218C */
-#define SDR0_SDSTP1_DBGEN_FUNC 0x00000000
-#define SDR0_SDSTP1_DBGEN_TRACE 0x00000010
-#define SDR0_SDSTP1_DBGEN_ENCODE(n) ((((unsigned long)(n))&0x03)<<4) /* $218C */
-#define SDR0_SDSTP1_DBGEN_DECODE(n) ((((unsigned long)(n))>>4)&0x03) /* $218C */
-#define SDR0_SDSTP1_ETH_MASK 0x00000004
-#define SDR0_SDSTP1_ETH_10_100 0x00000000
-#define SDR0_SDSTP1_ETH_GIGA 0x00000004
-#define SDR0_SDSTP1_ETH_ENCODE(n) ((((unsigned long)(n))&0x01)<<2)
-#define SDR0_SDSTP1_ETH_DECODE(n) ((((unsigned long)(n))>>2)&0x01)
-#define SDR0_SDSTP1_NTO1_MASK 0x00000001
-#define SDR0_SDSTP1_NTO1_DISABLE 0x00000000
-#define SDR0_SDSTP1_NTO1_ENABLE 0x00000001
-#define SDR0_SDSTP1_NTO1_ENCODE(n) ((((unsigned long)(n))&0x01)<<0)
-#define SDR0_SDSTP1_NTO1_DECODE(n) ((((unsigned long)(n))>>0)&0x01)
-
-#define SDR0_SDSTP2 0x0022
-#define SDR0_SDSTP2_P1AE_MASK 0x80000000
-#define SDR0_SDSTP2_P1AE_DISABLE 0x00000000
-#define SDR0_SDSTP2_P1AE_ENABLE 0x80000000
-#define SDR0_SDSTP2_P1AE_ENCODE(n) ((((unsigned long)(n))&0x01)<<31)
-#define SDR0_SDSTP2_P1AE_DECODE(n) ((((unsigned long)(n))>>31)&0x01)
-#define SDR0_SDSTP2_P1HCE_MASK 0x40000000
-#define SDR0_SDSTP2_P1HCE_DISABLE 0x00000000
-#define SDR0_SDSTP2_P1HCE_ENABLE 0x40000000
-#define SDR0_SDSTP2_P1HCE_ENCODE(n) ((((unsigned long)(n))&0x01)<<30)
-#define SDR0_SDSTP2_P1HCE_DECODE(n) ((((unsigned long)(n))>>30)&0x01)
-#define SDR0_SDSTP2_P1ISE_MASK 0x20000000
-#define SDR0_SDSTP2_P1ISE_DISABLE 0x00000000
-#define SDR0_SDSTP2_P1ISE_ENABLE 0x20000000
-#define SDR0_SDSTP2_P1ISE_ENCODE(n) ((((unsigned long)(n))&0x01)<<29)
-#define SDR0_SDSTP2_P1ISE_DECODE(n) ((((unsigned long)(n))>>29)&0x01)
-#define SDR0_SDSTP2_P1CWE_MASK 0x10000000
-#define SDR0_SDSTP2_P1CWE_DISABLE 0x00000000
-#define SDR0_SDSTP2_P1CWE_ENABLE 0x10000000
-#define SDR0_SDSTP2_P1CWE_ENCODE(n) ((((unsigned long)(n))&0x01)<<28)
-#define SDR0_SDSTP2_P1CWE_DECODE(n) ((((unsigned long)(n))>>28)&0x01)
-#define SDR0_SDSTP2_P1PIM_MASK 0x0F000000
-#define SDR0_SDSTP2_P1PIM_ENCODE(n) ((((unsigned long)(n))&0x0F)<<24)
-#define SDR0_SDSTP2_P1PIM_DECODE(n) ((((unsigned long)(n))>>24)&0x0F)
-#define SDR0_SDSTP2_P1R64E_MASK 0x00800000
-#define SDR0_SDSTP2_P1R64E_DISABLE 0x00000000
-#define SDR0_SDSTP2_P1R64E_ENABLE 0x00800000
-#define SDR0_SDSTP2_P1R64E_ENCODE(n) ((((unsigned long)(n))&0x01)<<23)
-#define SDR0_SDSTP2_P1R64E_DECODE(n) ((((unsigned long)(n))>>23)&0x01)
-#define SDR0_SDSTP2_P1XFS_MASK 0x00600000
-#define SDR0_SDSTP2_P1XFS_100_133 0x00000000
-#define SDR0_SDSTP2_P1XFS_66_100 0x00200000
-#define SDR0_SDSTP2_P1XFS_50_66 0x00400000
-#define SDR0_SDSTP2_P1XFS_0_50 0x00600000
-#define SDR0_SDSTP2_P1XFS_ENCODE(n) ((((unsigned long)(n))&0x03)<<21)
-#define SDR0_SDSTP2_P1XFS_DECODE(n) ((((unsigned long)(n))>>21)&0x03)
-#define SDR0_SDSTP2_P2AE_MASK 0x00040000
-#define SDR0_SDSTP2_P2AE_DISABLE 0x00000000
-#define SDR0_SDSTP2_P2AE_ENABLE 0x00040000
-#define SDR0_SDSTP2_P2AE_ENCODE(n) ((((unsigned long)(n))&0x01)<<18)
-#define SDR0_SDSTP2_P2AE_DECODE(n) ((((unsigned long)(n))>>18)&0x01)
-#define SDR0_SDSTP2_P2HCE_MASK 0x00020000
-#define SDR0_SDSTP2_P2HCE_DISABLE 0x00000000
-#define SDR0_SDSTP2_P2HCE_ENABLE 0x00020000
-#define SDR0_SDSTP2_P2HCE_ENCODE(n) ((((unsigned long)(n))&0x01)<<17)
-#define SDR0_SDSTP2_P2HCE_DECODE(n) ((((unsigned long)(n))>>17)&0x01)
-#define SDR0_SDSTP2_P2ISE_MASK 0x00010000
-#define SDR0_SDSTP2_P2ISE_DISABLE 0x00000000
-#define SDR0_SDSTP2_P2ISE_ENABLE 0x00010000
-#define SDR0_SDSTP2_P2ISE_ENCODE(n) ((((unsigned long)(n))&0x01)<<16)
-#define SDR0_SDSTP2_P2ISE_DECODE(n) ((((unsigned long)(n))>>16)&0x01)
-#define SDR0_SDSTP2_P2CWE_MASK 0x00008000
-#define SDR0_SDSTP2_P2CWE_DISABLE 0x00000000
-#define SDR0_SDSTP2_P2CWE_ENABLE 0x00008000
-#define SDR0_SDSTP2_P2CWE_ENCODE(n) ((((unsigned long)(n))&0x01)<<15)
-#define SDR0_SDSTP2_P2CWE_DECODE(n) ((((unsigned long)(n))>>15)&0x01)
-#define SDR0_SDSTP2_P2PIM_MASK 0x00007800
-#define SDR0_SDSTP2_P2PIM_ENCODE(n) ((((unsigned long)(n))&0x0F)<<11)
-#define SDR0_SDSTP2_P2PIM_DECODE(n) ((((unsigned long)(n))>>11)&0x0F)
-#define SDR0_SDSTP2_P2XFS_MASK 0x00000300
-#define SDR0_SDSTP2_P2XFS_100_133 0x00000000
-#define SDR0_SDSTP2_P2XFS_66_100 0x00000100
-#define SDR0_SDSTP2_P2XFS_50_66 0x00000200
-#define SDR0_SDSTP2_P2XFS_0_50 0x00000100
-#define SDR0_SDSTP2_P2XFS_ENCODE(n) ((((unsigned long)(n))&0x03)<<8)
-#define SDR0_SDSTP2_P2XFS_DECODE(n) ((((unsigned long)(n))>>8)&0x03)
-
-#define SDR0_SDSTP3 0x0023
-
-#define SDR0_PINSTP 0x0040
-#define SDR0_PINSTP_BOOTSTRAP_MASK 0xC0000000 /* Strap Bits */
-#define SDR0_PINSTP_BOOTSTRAP_SETTINGS0 0x00000000 /* Default strap settings 0
- (EBC boot) */
-#define SDR0_PINSTP_BOOTSTRAP_SETTINGS1 0x40000000 /* Default strap settings 1
- (PCI boot) */
-#define SDR0_PINSTP_BOOTSTRAP_IIC_54_EN 0x80000000 /* Serial Device Enabled -
- Addr = 0x54 */
-#define SDR0_PINSTP_BOOTSTRAP_IIC_50_EN 0xC0000000 /* Serial Device Enabled -
- Addr = 0x50 */
-#define SDR0_SDCS 0x0060
-#define SDR0_ECID0 0x0080
-#define SDR0_ECID1 0x0081
-#define SDR0_ECID2 0x0082
-#define SDR0_JTAG 0x00C0
-
-#define SDR0_DDR0 0x00E1
-#define SDR0_DDR0_DPLLRST 0x80000000
-#define SDR0_DDR0_DDRM_MASK 0x60000000
-#define SDR0_DDR0_DDRM_DDR1 0x20000000
-#define SDR0_DDR0_DDRM_DDR2 0x40000000
-#define SDR0_DDR0_DDRM_ENCODE(n) ((((unsigned long)(n))&0x03)<<29)
-#define SDR0_DDR0_DDRM_DECODE(n) ((((unsigned long)(n))>>29)&0x03)
-#define SDR0_DDR0_TUNE_ENCODE(n) ((((unsigned long)(n))&0x2FF)<<0)
-#define SDR0_DDR0_TUNE_DECODE(n) ((((unsigned long)(n))>>0)&0x2FF)
-
-#define SDR0_UART0 0x0120
-#define SDR0_UART1 0x0121
-#define SDR0_UART2 0x0122
-#define SDR0_SLPIPE 0x0220
-
-#define SDR0_AMP0 0x0240
-#define SDR0_AMP0_PRIORITY 0xFFFF0000
-#define SDR0_AMP0_ALTERNATE_PRIORITY 0x0000FF00
-#define SDR0_AMP0_RESERVED_BITS_MASK 0x000000FF
-
-#define SDR0_AMP1 0x0241
-#define SDR0_AMP1_PRIORITY 0xFC000000
-#define SDR0_AMP1_ALTERNATE_PRIORITY 0x0000E000
-#define SDR0_AMP1_RESERVED_BITS_MASK 0x03FF1FFF
-
-#define SDR0_MIRQ0 0x0260
-#define SDR0_MIRQ1 0x0261
-#define SDR0_MALTBL 0x0280
-#define SDR0_MALRBL 0x02A0
-#define SDR0_MALTBS 0x02C0
-#define SDR0_MALRBS 0x02E0
-
-/* Reserved for Customer Use */
-#define SDR0_CUST0 0x4000
-#define SDR0_CUST0_AUTONEG_MASK 0x8000000
-#define SDR0_CUST0_NO_AUTONEG 0x0000000
-#define SDR0_CUST0_AUTONEG 0x8000000
-#define SDR0_CUST0_ETH_FORCE_MASK 0x6000000
-#define SDR0_CUST0_ETH_FORCE_10MHZ 0x0000000
-#define SDR0_CUST0_ETH_FORCE_100MHZ 0x2000000
-#define SDR0_CUST0_ETH_FORCE_1000MHZ 0x4000000
-#define SDR0_CUST0_ETH_DUPLEX_MASK 0x1000000
-#define SDR0_CUST0_ETH_HALF_DUPLEX 0x0000000
-#define SDR0_CUST0_ETH_FULL_DUPLEX 0x1000000
-
-#define SDR0_SDSTP4 0x4001
-#define SDR0_CUST1 0x4002
-#define SDR0_SDSTP5 0x4003
-#define SDR0_CUST2 0x4004
-#define SDR0_SDSTP6 0x4005
-#define SDR0_CUST3 0x4006
-#define SDR0_SDSTP7 0x4007
-
-#define SDR0_PFC0 0x4100
-#define SDR0_PFC0_GPIO_0 0x80000000
-#define SDR0_PFC0_PCIX0REQ2_N 0x00000000
-#define SDR0_PFC0_GPIO_1 0x40000000
-#define SDR0_PFC0_PCIX0REQ3_N 0x00000000
-#define SDR0_PFC0_GPIO_2 0x20000000
-#define SDR0_PFC0_PCIX0GNT2_N 0x00000000
-#define SDR0_PFC0_GPIO_3 0x10000000
-#define SDR0_PFC0_PCIX0GNT3_N 0x00000000
-#define SDR0_PFC0_GPIO_4 0x08000000
-#define SDR0_PFC0_PCIX1REQ2_N 0x00000000
-#define SDR0_PFC0_GPIO_5 0x04000000
-#define SDR0_PFC0_PCIX1REQ3_N 0x00000000
-#define SDR0_PFC0_GPIO_6 0x02000000
-#define SDR0_PFC0_PCIX1GNT2_N 0x00000000
-#define SDR0_PFC0_GPIO_7 0x01000000
-#define SDR0_PFC0_PCIX1GNT3_N 0x00000000
-#define SDR0_PFC0_GPIO_8 0x00800000
-#define SDR0_PFC0_PERREADY 0x00000000
-#define SDR0_PFC0_GPIO_9 0x00400000
-#define SDR0_PFC0_PERCS1_N 0x00000000
-#define SDR0_PFC0_GPIO_10 0x00200000
-#define SDR0_PFC0_PERCS2_N 0x00000000
-#define SDR0_PFC0_GPIO_11 0x00100000
-#define SDR0_PFC0_IRQ0 0x00000000
-#define SDR0_PFC0_GPIO_12 0x00080000
-#define SDR0_PFC0_IRQ1 0x00000000
-#define SDR0_PFC0_GPIO_13 0x00040000
-#define SDR0_PFC0_IRQ2 0x00000000
-#define SDR0_PFC0_GPIO_14 0x00020000
-#define SDR0_PFC0_IRQ3 0x00000000
-#define SDR0_PFC0_GPIO_15 0x00010000
-#define SDR0_PFC0_IRQ4 0x00000000
-#define SDR0_PFC0_GPIO_16 0x00008000
-#define SDR0_PFC0_IRQ5 0x00000000
-#define SDR0_PFC0_GPIO_17 0x00004000
-#define SDR0_PFC0_PERBE0_N 0x00000000
-#define SDR0_PFC0_GPIO_18 0x00002000
-#define SDR0_PFC0_PCI0GNT0_N 0x00000000
-#define SDR0_PFC0_GPIO_19 0x00001000
-#define SDR0_PFC0_PCI0GNT1_N 0x00000000
-#define SDR0_PFC0_GPIO_20 0x00000800
-#define SDR0_PFC0_PCI0REQ0_N 0x00000000
-#define SDR0_PFC0_GPIO_21 0x00000400
-#define SDR0_PFC0_PCI0REQ1_N 0x00000000
-#define SDR0_PFC0_GPIO_22 0x00000200
-#define SDR0_PFC0_PCI1GNT0_N 0x00000000
-#define SDR0_PFC0_GPIO_23 0x00000100
-#define SDR0_PFC0_PCI1GNT1_N 0x00000000
-#define SDR0_PFC0_GPIO_24 0x00000080
-#define SDR0_PFC0_PCI1REQ0_N 0x00000000
-#define SDR0_PFC0_GPIO_25 0x00000040
-#define SDR0_PFC0_PCI1REQ1_N 0x00000000
-#define SDR0_PFC0_GPIO_26 0x00000020
-#define SDR0_PFC0_PCI2GNT0_N 0x00000000
-#define SDR0_PFC0_GPIO_27 0x00000010
-#define SDR0_PFC0_PCI2GNT1_N 0x00000000
-#define SDR0_PFC0_GPIO_28 0x00000008
-#define SDR0_PFC0_PCI2REQ0_N 0x00000000
-#define SDR0_PFC0_GPIO_29 0x00000004
-#define SDR0_PFC0_PCI2REQ1_N 0x00000000
-#define SDR0_PFC0_GPIO_30 0x00000002
-#define SDR0_PFC0_UART1RX 0x00000000
-#define SDR0_PFC0_GPIO_31 0x00000001
-#define SDR0_PFC0_UART1TX 0x00000000
-
-#define SDR0_PFC1 0x4101
-#define SDR0_PFC1_UART1_CTS_RTS_MASK 0x02000000
-#define SDR0_PFC1_UART1_DSR_DTR 0x00000000
-#define SDR0_PFC1_UART1_CTS_RTS 0x02000000
-#define SDR0_PFC1_UART2_IN_SERVICE_MASK 0x01000000
-#define SDR0_PFC1_UART2_NOT_IN_SERVICE 0x00000000
-#define SDR0_PFC1_UART2_IN_SERVICE 0x01000000
-#define SDR0_PFC1_ETH_GIGA_MASK 0x00200000
-#define SDR0_PFC1_ETH_10_100 0x00000000
-#define SDR0_PFC1_ETH_GIGA 0x00200000
-#define SDR0_PFC1_ETH_GIGA_ENCODE(n) ((((unsigned long)(n))&0x1)<<21)
-#define SDR0_PFC1_ETH_GIGA_DECODE(n) ((((unsigned long)(n))>>21)&0x01)
-#define SDR0_PFC1_CPU_TRACE_MASK 0x00180000 /* $218C */
-#define SDR0_PFC1_CPU_NO_TRACE 0x00000000
-#define SDR0_PFC1_CPU_TRACE 0x00080000
-#define SDR0_PFC1_CPU_TRACE_ENCODE(n) ((((unsigned long)(n))&0x3)<<19)
- /* $218C */
-#define SDR0_PFC1_CPU_TRACE_DECODE(n) ((((unsigned long)(n))>>19)&0x03)
- /* $218C */
-
-#define SDR0_MFR 0x4300
-#endif /* CONFIG_440SPE */
-
-#if defined(CONFIG_460EX) || defined(CONFIG_460GT)
-/* Pin Function Control Register 0 (SDR0_PFC0) */
-#define SDR0_PFC0 0x4100
-#define SDR0_PFC0_DBG 0x00008000 /* debug enable */
-#define SDR0_PFC0_G49E 0x00004000 /* GPIO 49 enable */
-#define SDR0_PFC0_G50E 0x00002000 /* GPIO 50 enable */
-#define SDR0_PFC0_G51E 0x00001000 /* GPIO 51 enable */
-#define SDR0_PFC0_G52E 0x00000800 /* GPIO 52 enable */
-#define SDR0_PFC0_G53E 0x00000400 /* GPIO 53 enable */
-#define SDR0_PFC0_G54E 0x00000200 /* GPIO 54 enable */
-#define SDR0_PFC0_G55E 0x00000100 /* GPIO 55 enable */
-#define SDR0_PFC0_G56E 0x00000080 /* GPIO 56 enable */
-#define SDR0_PFC0_G57E 0x00000040 /* GPIO 57 enable */
-#define SDR0_PFC0_G58E 0x00000020 /* GPIO 58 enable */
-#define SDR0_PFC0_G59E 0x00000010 /* GPIO 59 enable */
-#define SDR0_PFC0_G60E 0x00000008 /* GPIO 60 enable */
-#define SDR0_PFC0_G61E 0x00000004 /* GPIO 61 enable */
-#define SDR0_PFC0_G62E 0x00000002 /* GPIO 62 enable */
-#define SDR0_PFC0_G63E 0x00000001 /* GPIO 63 enable */
-
-/* Pin Function Control Register 1 (SDR0_PFC1) */
-#define SDR0_PFC1 0x4101
-#define SDR0_PFC1_U1ME_MASK 0x02000000 /* UART1 Mode Enable */
-#define SDR0_PFC1_U1ME_DSR_DTR 0x00000000 /* UART1 in DSR/DTR Mode */
-#define SDR0_PFC1_U1ME_CTS_RTS 0x02000000 /* UART1 in CTS/RTS Mode */
-#define SDR0_PFC1_U0ME_MASK 0x00080000 /* UART0 Mode Enable */
-#define SDR0_PFC1_U0ME_DSR_DTR 0x00000000 /* UART0 in DSR/DTR Mode */
-#define SDR0_PFC1_U0ME_CTS_RTS 0x00080000 /* UART0 in CTS/RTS Mode */
-#define SDR0_PFC1_U0IM_MASK 0x00040000 /* UART0 Interface Mode */
-#define SDR0_PFC1_U0IM_8PINS 0x00000000 /* UART0 Interface Mode 8 pins*/
-#define SDR0_PFC1_U0IM_4PINS 0x00040000 /* UART0 Interface Mode 4 pins*/
-#define SDR0_PFC1_SIS_MASK 0x00020000 /* SCP or IIC1 Selection */
-#define SDR0_PFC1_SIS_SCP_SEL 0x00000000 /* SCP Selected */
-#define SDR0_PFC1_SIS_IIC1_SEL 0x00020000 /* IIC1 Selected */
-
-#define SDR0_ECID0 0x0080
-#define SDR0_ECID1 0x0081
-#define SDR0_ECID2 0x0082
-#define SDR0_ECID3 0x0083
-
-/* Ethernet PLL Configuration Register (SDR0_ETH_PLL) */
-#define SDR0_ETH_PLL 0x4102
-#define SDR0_ETH_PLL_PLLLOCK 0x80000000 /*Ethernet PLL lock indication*/
-#define SDR0_ETH_PLL_REF_CLK_SEL 0x10000000 /* Ethernet reference clock */
-#define SDR0_ETH_PLL_BYPASS 0x08000000 /* bypass mode enable */
-#define SDR0_ETH_PLL_STOPCLK 0x04000000 /* output clock disable */
-#define SDR0_ETH_PLL_TUNE_MASK 0x03FF0000 /* loop stability tuning bits */
-#define SDR0_ETH_PLL_TUNE_ENCODE(n) ((((unsigned long)(n))&0x3ff)<<16)
-#define SDR0_ETH_PLL_MULTI_MASK 0x0000FF00 /* frequency multiplication */
-#define SDR0_ETH_PLL_MULTI_ENCODE(n) ((((unsigned long)(n))&0xff)<<8)
-#define SDR0_ETH_PLL_RANGEB_MASK 0x000000F0 /* PLLOUTB/C frequency */
-#define SDR0_ETH_PLL_RANGEB_ENCODE(n) ((((unsigned long)(n))&0x0f)<<4)
-#define SDR0_ETH_PLL_RANGEA_MASK 0x0000000F /* PLLOUTA frequency */
-#define SDR0_ETH_PLL_RANGEA_ENCODE(n) (((unsigned long)(n))&0x0f)
-
-/* Ethernet Configuration Register (SDR0_ETH_CFG) */
-#define SDR0_ETH_CFG 0x4103
-#define SDR0_ETH_CFG_SGMII3_LPBK 0x00800000 /*SGMII3 port loopback
- enable */
-#define SDR0_ETH_CFG_SGMII2_LPBK 0x00400000 /*SGMII2 port loopback
- enable */
-#define SDR0_ETH_CFG_SGMII1_LPBK 0x00200000 /*SGMII1 port loopback
- enable */
-#define SDR0_ETH_CFG_SGMII0_LPBK 0x00100000 /*SGMII0 port loopback
- enable */
-#define SDR0_ETH_CFG_SGMII_MASK 0x00070000 /*SGMII Mask */
-#define SDR0_ETH_CFG_SGMII2_ENABLE 0x00040000 /*SGMII2 port enable */
-#define SDR0_ETH_CFG_SGMII1_ENABLE 0x00020000 /*SGMII1 port enable */
-#define SDR0_ETH_CFG_SGMII0_ENABLE 0x00010000 /*SGMII0 port enable */
-#define SDR0_ETH_CFG_TAHOE1_BYPASS 0x00002000 /*TAHOE1 Bypass selector */
-#define SDR0_ETH_CFG_TAHOE0_BYPASS 0x00001000 /*TAHOE0 Bypass selector */
-#define SDR0_ETH_CFG_EMAC3_PHY_CLK_SEL 0x00000800 /*EMAC 3 PHY clock selector*/
-#define SDR0_ETH_CFG_EMAC2_PHY_CLK_SEL 0x00000400 /*EMAC 2 PHY clock selector*/
-#define SDR0_ETH_CFG_EMAC1_PHY_CLK_SEL 0x00000200 /*EMAC 1 PHY clock selector*/
-#define SDR0_ETH_CFG_EMAC0_PHY_CLK_SEL 0x00000100 /*EMAC 0 PHY clock selector*/
-#define SDR0_ETH_CFG_EMAC_2_1_SWAP 0x00000080 /*Swap EMAC2 with EMAC1 */
-#define SDR0_ETH_CFG_EMAC_0_3_SWAP 0x00000040 /*Swap EMAC0 with EMAC3 */
-#define SDR0_ETH_CFG_MDIO_SEL_MASK 0x00000030 /*MDIO source selector mask*/
-#define SDR0_ETH_CFG_MDIO_SEL_EMAC0 0x00000000 /*MDIO source - EMAC0 */
-#define SDR0_ETH_CFG_MDIO_SEL_EMAC1 0x00000010 /*MDIO source - EMAC1 */
-#define SDR0_ETH_CFG_MDIO_SEL_EMAC2 0x00000020 /*MDIO source - EMAC2 */
-#define SDR0_ETH_CFG_MDIO_SEL_EMAC3 0x00000030 /*MDIO source - EMAC3 */
-#define SDR0_ETH_CFG_ZMII_MODE_MASK 0x0000000C /*ZMII bridge mode selector
- mask */
-#define SDR0_ETH_CFG_ZMII_SEL_MII 0x00000000 /*ZMII bridge mode - MII */
-#define SDR0_ETH_CFG_ZMII_SEL_SMII 0x00000004 /*ZMII bridge mode - SMII */
-#define SDR0_ETH_CFG_ZMII_SEL_RMII_10 0x00000008 /*ZMII bridge mode - RMII
- (10 Mbps) */
-#define SDR0_ETH_CFG_ZMII_SEL_RMII_100 0x0000000C /*ZMII bridge mode - RMII
- (100 Mbps) */
-#define SDR0_ETH_CFG_GMC1_BRIDGE_SEL 0x00000002 /*GMC Port 1 bridge
- selector */
-#define SDR0_ETH_CFG_GMC0_BRIDGE_SEL 0x00000001 /*GMC Port 0 bridge
- selector */
-
-#define SDR0_ETH_CFG_ZMII_MODE_SHIFT 4
-#define SDR0_ETH_CFG_ZMII_MII_MODE 0x00
-#define SDR0_ETH_CFG_ZMII_SMII_MODE 0x01
-#define SDR0_ETH_CFG_ZMII_RMII_MODE_10M 0x10
-#define SDR0_ETH_CFG_ZMII_RMII_MODE_100M 0x11
-
-/* Ethernet Status Register */
-#define SDR0_ETH_STS 0x4104
-
-/* Miscealleneaous Function Reg. (SDR0_MFR) */
-#define SDR0_MFR 0x4300
-#define SDR0_MFR_T0TxFL 0x00800000 /* force parity error TAHOE0 Tx
- FIFO bits 0:63 */
-#define SDR0_MFR_T0TxFH 0x00400000 /* force parity error TAHOE0 Tx
- FIFO bits 64:127 */
-#define SDR0_MFR_T1TxFL 0x00200000 /* force parity error TAHOE1 Tx
- FIFO bits 0:63 */
-#define SDR0_MFR_T1TxFH 0x00100000 /* force parity error TAHOE1 Tx
- FIFO bits 64:127 */
-#define SDR0_MFR_E0TxFL 0x00008000 /* force parity error EMAC0 Tx
- FIFO bits 0:63 */
-#define SDR0_MFR_E0TxFH 0x00004000 /* force parity error EMAC0 Tx
- FIFO bits 64:127 */
-#define SDR0_MFR_E0RxFL 0x00002000 /* force parity error EMAC0 Rx
- FIFO bits 0:63 */
-#define SDR0_MFR_E0RxFH 0x00001000 /* force parity error EMAC0 Rx
- FIFO bits 64:127 */
-#define SDR0_MFR_E1TxFL 0x00000800 /* force parity error EMAC1 Tx
- FIFO bits 0:63 */
-#define SDR0_MFR_E1TxFH 0x00000400 /* force parity error EMAC1 Tx
- FIFO bits 64:127 */
-#define SDR0_MFR_E1RxFL 0x00000200 /* force parity error EMAC1 Rx
- FIFO bits 0:63 */
-#define SDR0_MFR_E1RxFH 0x00000100 /* force parity error EMAC1 Rx
- FIFO bits 64:127 */
-#define SDR0_MFR_E2TxFL 0x00000080 /* force parity error EMAC2 Tx
- FIFO bits 0:63 */
-#define SDR0_MFR_E2TxFH 0x00000040 /* force parity error EMAC2 Tx
- FIFO bits 64:127 */
-#define SDR0_MFR_E2RxFL 0x00000020 /* force parity error EMAC2 Rx
- FIFO bits 0:63 */
-#define SDR0_MFR_E2RxFH 0x00000010 /* force parity error EMAC2 Rx
- FIFO bits 64:127 */
-#define SDR0_MFR_E3TxFL 0x00000008 /* force parity error EMAC3 Tx
- FIFO bits 0:63 */
-#define SDR0_MFR_E3TxFH 0x00000004 /* force parity error EMAC3 Tx
- FIFO bits 64:127 */
-#define SDR0_MFR_E3RxFL 0x00000002 /* force parity error EMAC3 Rx
- FIFO bits 0:63 */
-#define SDR0_MFR_E3RxFH 0x00000001 /* force parity error EMAC3 Rx
- FIFO bits 64:127 */
-
-/* EMACx TX Status Register (SDR0_EMACxTXST)*/
-#define SDR0_EMAC0TXST 0x4400
-#define SDR0_EMAC1TXST 0x4401
-#define SDR0_EMAC2TXST 0x4402
-#define SDR0_EMAC3TXST 0x4403
-
-#define SDR0_EMACxTXST_FUR 0x02000000 /*TX FIFO underrun */
-#define SDR0_EMACxTXST_BC 0x01000000 /*broadcase address */
-#define SDR0_EMACxTXST_MC 0x00800000 /*multicast address */
-#define SDR0_EMACxTXST_UC 0x00400000 /*unicast address */
-#define SDR0_EMACxTXST_FP 0x00200000 /*frame paused by control packet */
-#define SDR0_EMACxTXST_BFCS 0x00100000 /*bad FCS in the transmitted frame */
-#define SDR0_EMACxTXST_CPF 0x00080000 /*TX control pause frame */
-#define SDR0_EMACxTXST_CF 0x00040000 /*TX control frame */
-#define SDR0_EMACxTXST_MSIZ 0x00020000 /* 1024-maxsize bytes transmitted */
-#define SDR0_EMACxTXST_1023 0x00010000 /*512-1023 bytes transmitted */
-#define SDR0_EMACxTXST_511 0x00008000 /*256-511 bytes transmitted */
-#define SDR0_EMACxTXST_255 0x00004000 /*128-255 bytes transmitted */
-#define SDR0_EMACxTXST_127 0x00002000 /*65-127 bytes transmitted */
-#define SDR0_EMACxTXST_64 0x00001000 /*64 bytes transmitted */
-#define SDR0_EMACxTXST_SQE 0x00000800 /*SQE indication */
-#define SDR0_EMACxTXST_LOC 0x00000400 /*loss of carrier sense */
-#define SDR0_EMACxTXST_IERR 0x00000080 /*EMAC internal error */
-#define SDR0_EMACxTXST_EDF 0x00000040 /*excessive deferral */
-#define SDR0_EMACxTXST_ECOL 0x00000020 /*excessive collisions */
-#define SDR0_EMACxTXST_LCOL 0x00000010 /*late collision */
-#define SDR0_EMACxTXST_DFFR 0x00000008 /*deferred frame */
-#define SDR0_EMACxTXST_MCOL 0x00000004 /*multiple collision frame */
-#define SDR0_EMACxTXST_SCOL 0x00000002 /*single collision frame */
-#define SDR0_EMACxTXST_TXOK 0x00000001 /*transmit OK */
-
-/* EMACx RX Status Register (SDR0_EMACxRXST)*/
-#define SDR0_EMAC0RXST 0x4404
-#define SDR0_EMAC1RXST 0x4405
-#define SDR0_EMAC2RXST 0x4406
-#define SDR0_EMAC3RXST 0x4407
-
-#define SDR0_EMACxRXST_FOR 0x20000000 /* RX FIFO overrun */
-#define SDR0_EMACxRXST_BC 0x10000000 /* broadcast address */
-#define SDR0_EMACxRXST_MC 0x08000000 /* multicast address */
-#define SDR0_EMACxRXST_UC 0x04000000 /* unicast address */
-#define SDR0_EMACxRXST_UPR_MASK 0x03800000 /* user priority field */
-#define SDR0_EMACxRXST_UPR_ENCODE(n) ((((unsigned long)(n))&0x07)<<23)
-#define SDR0_EMACxRXST_VLAN 0x00400000 /* RX VLAN tagged frame */
-#define SDR0_EMACxRXST_LOOP 0x00200000 /* received in loop-back mode */
-#define SDR0_EMACxRXST_UOP 0x00100000 /* RX unsupported opcode */
-#define SDR0_EMACxRXST_CPF 0x00080000 /* RX control pause frame */
-#define SDR0_EMACxRXST_CF 0x00040000 /* RX control frame*/
-#define SDR0_EMACxRXST_MSIZ 0x00020000 /* 1024-MaxSize bytes recieved*/
-#define SDR0_EMACxRXST_1023 0x00010000 /* 512-1023 bytes received */
-#define SDR0_EMACxRXST_511 0x00008000 /* 128-511 bytes received */
-#define SDR0_EMACxRXST_255 0x00004000 /* 128-255 bytes received */
-#define SDR0_EMACxRXST_127 0x00002000 /* 65-127 bytes received */
-#define SDR0_EMACxRXST_64 0x00001000 /* 64 bytes received */
-#define SDR0_EMACxRXST_RUNT 0x00000800 /* runt frame */
-#define SDR0_EMACxRXST_SEVT 0x00000400 /* short event */
-#define SDR0_EMACxRXST_AERR 0x00000200 /* alignment error */
-#define SDR0_EMACxRXST_SERR 0x00000100 /* received with symbol error */
-#define SDR0_EMACxRXST_BURST 0x00000040 /* received burst */
-#define SDR0_EMACxRXST_F2L 0x00000020 /* frame is to long */
-#define SDR0_EMACxRXST_OERR 0x00000010 /* out of range length error */
-#define SDR0_EMACxRXST_IERR 0x00000008 /* in range length error */
-#define SDR0_EMACxRXST_LOST 0x00000004 /* frame lost due to internal
- EMAC receive error */
-#define SDR0_EMACxRXST_BFCS 0x00000002 /* bad FCS in the recieved frame */
-#define SDR0_EMACxRXST_RXOK 0x00000001 /* Recieve OK */
-
-/* EMACx TX Status Register (SDR0_EMACxREJCNT)*/
-#define SDR0_EMAC0REJCNT 0x4408
-#define SDR0_EMAC1REJCNT 0x4409
-#define SDR0_EMAC2REJCNT 0x440A
-#define SDR0_EMAC3REJCNT 0x440B
-
-#define SDR0_DDR0 0x00E1
-#define SDR0_DDR0_DPLLRST 0x80000000
-#define SDR0_DDR0_DDRM_MASK 0x60000000
-#define SDR0_DDR0_DDRM_DDR1 0x20000000
-#define SDR0_DDR0_DDRM_DDR2 0x40000000
-#define SDR0_DDR0_DDRM_ENCODE(n) ((((unsigned long)(n))&0x03)<<29)
-#define SDR0_DDR0_DDRM_DECODE(n) ((((unsigned long)(n))>>29)&0x03)
-#define SDR0_DDR0_TUNE_ENCODE(n) ((((unsigned long)(n))&0x2FF)<<0)
-#define SDR0_DDR0_TUNE_DECODE(n) ((((unsigned long)(n))>>0)&0x2FF)
-
-#define AHB_TOP 0xA4
-#define AHB_BOT 0xA5
-#define SDR0_AHB_CFG 0x370
-#define SDR0_USB2HOST_CFG 0x371
-#endif /* CONFIG_460EX || CONFIG_460GT */
-
-#define SDR0_SDCS_SDD (0x80000000 >> 31)
-
-#if defined(CONFIG_440GP)
-#define CPC0_STRP1_PAE_MASK (0x80000000 >> 11)
-#define CPC0_STRP1_PISE_MASK (0x80000000 >> 13)
-#endif /* defined(CONFIG_440GP) */
-#if defined(CONFIG_440GX) || defined(CONFIG_440SP) || \
- defined(CONFIG_460EX) || defined(CONFIG_460GT)
-#define SDR0_SDSTP1_PAE_MASK (0x80000000 >> 13)
-#define SDR0_SDSTP1_PISE_MASK (0x80000000 >> 15)
-#endif /* defined(CONFIG_440GX) || defined(CONFIG_440SP) */
-#if defined(CONFIG_440EP) || defined(CONFIG_440GR) || \
- defined(CONFIG_440EPX) || defined(CONFIG_440GRX)
-#define SDR0_SDSTP1_PAE_MASK (0x80000000 >> 21)
-#define SDR0_SDSTP1_PAME_MASK (0x80000000 >> 27)
-#endif /* defined(CONFIG_440EP) || defined(CONFIG_440GR) */
-
-#define SDR0_UARTX_UXICS_MASK 0xF0000000
-#define SDR0_UARTX_UXICS_PLB 0x20000000
-#define SDR0_UARTX_UXEC_MASK 0x00800000
-#define SDR0_UARTX_UXEC_INT 0x00000000
-#define SDR0_UARTX_UXEC_EXT 0x00800000
-#define SDR0_UARTX_UXDTE_MASK 0x00400000
-#define SDR0_UARTX_UXDTE_DISABLE 0x00000000
-#define SDR0_UARTX_UXDTE_ENABLE 0x00400000
-#define SDR0_UARTX_UXDRE_MASK 0x00200000
-#define SDR0_UARTX_UXDRE_DISABLE 0x00000000
-#define SDR0_UARTX_UXDRE_ENABLE 0x00200000
-#define SDR0_UARTX_UXDC_MASK 0x00100000
-#define SDR0_UARTX_UXDC_NOTCLEARED 0x00000000
-#define SDR0_UARTX_UXDC_CLEARED 0x00100000
-#define SDR0_UARTX_UXDIV_MASK 0x000000FF
-#define SDR0_UARTX_UXDIV_ENCODE(n) ((((unsigned long)(n))&0xFF)<<0)
-#define SDR0_UARTX_UXDIV_DECODE(n) ((((((unsigned long)(n))>>0)-1)&0xFF)+1)
-
-#define SDR0_CPU440_EARV_MASK 0x30000000
-#define SDR0_CPU440_EARV_EBC 0x10000000
-#define SDR0_CPU440_EARV_PCI 0x20000000
-#define SDR0_CPU440_EARV_ENCODE(n) ((((unsigned long)(n))&0x03)<<28)
-#define SDR0_CPU440_EARV_DECODE(n) ((((unsigned long)(n))>>28)&0x03)
-#define SDR0_CPU440_NTO1_MASK 0x00000002
-#define SDR0_CPU440_NTO1_NTOP 0x00000000
-#define SDR0_CPU440_NTO1_NTO1 0x00000002
-#define SDR0_CPU440_NTO1_ENCODE(n) ((((unsigned long)(n))&0x01)<<1)
-#define SDR0_CPU440_NTO1_DECODE(n) ((((unsigned long)(n))>>1)&0x01)
-
-#define SDR0_XCR_PAE_MASK 0x80000000
-#define SDR0_XCR_PAE_DISABLE 0x00000000
-#define SDR0_XCR_PAE_ENABLE 0x80000000
-#define SDR0_XCR_PAE_ENCODE(n) ((((unsigned long)(n))&0x01)<<31)
-#define SDR0_XCR_PAE_DECODE(n) ((((unsigned long)(n))>>31)&0x01)
-#define SDR0_XCR_PHCE_MASK 0x40000000
-#define SDR0_XCR_PHCE_DISABLE 0x00000000
-#define SDR0_XCR_PHCE_ENABLE 0x40000000
-#define SDR0_XCR_PHCE_ENCODE(n) ((((unsigned long)(n))&0x01)<<30)
-#define SDR0_XCR_PHCE_DECODE(n) ((((unsigned long)(n))>>30)&0x01)
-#define SDR0_XCR_PISE_MASK 0x20000000
-#define SDR0_XCR_PISE_DISABLE 0x00000000
-#define SDR0_XCR_PISE_ENABLE 0x20000000
-#define SDR0_XCR_PISE_ENCODE(n) ((((unsigned long)(n))&0x01)<<29)
-#define SDR0_XCR_PISE_DECODE(n) ((((unsigned long)(n))>>29)&0x01)
-#define SDR0_XCR_PCWE_MASK 0x10000000
-#define SDR0_XCR_PCWE_DISABLE 0x00000000
-#define SDR0_XCR_PCWE_ENABLE 0x10000000
-#define SDR0_XCR_PCWE_ENCODE(n) ((((unsigned long)(n))&0x01)<<28)
-#define SDR0_XCR_PCWE_DECODE(n) ((((unsigned long)(n))>>28)&0x01)
-#define SDR0_XCR_PPIM_MASK 0x0F000000
-#define SDR0_XCR_PPIM_ENCODE(n) ((((unsigned long)(n))&0x0F)<<24)
-#define SDR0_XCR_PPIM_DECODE(n) ((((unsigned long)(n))>>24)&0x0F)
-#define SDR0_XCR_PR64E_MASK 0x00800000
-#define SDR0_XCR_PR64E_DISABLE 0x00000000
-#define SDR0_XCR_PR64E_ENABLE 0x00800000
-#define SDR0_XCR_PR64E_ENCODE(n) ((((unsigned long)(n))&0x01)<<23)
-#define SDR0_XCR_PR64E_DECODE(n) ((((unsigned long)(n))>>23)&0x01)
-#define SDR0_XCR_PXFS_MASK 0x00600000
-#define SDR0_XCR_PXFS_HIGH 0x00000000
-#define SDR0_XCR_PXFS_MED 0x00200000
-#define SDR0_XCR_PXFS_LOW 0x00400000
-#define SDR0_XCR_PXFS_ENCODE(n) ((((unsigned long)(n))&0x03)<<21)
-#define SDR0_XCR_PXFS_DECODE(n) ((((unsigned long)(n))>>21)&0x03)
-#define SDR0_XCR_PDM_MASK 0x00000040
-#define SDR0_XCR_PDM_MULTIPOINT 0x00000000
-#define SDR0_XCR_PDM_P2P 0x00000040
-#define SDR0_XCR_PDM_ENCODE(n) ((((unsigned long)(n))&0x01)<<19)
-#define SDR0_XCR_PDM_DECODE(n) ((((unsigned long)(n))>>19)&0x01)
-
-#define SDR0_PFC0_UART1_DSR_CTS_EN_MASK 0x00030000
-#define SDR0_PFC0_GEIE_MASK 0x00003E00
-#define SDR0_PFC0_GEIE_TRE 0x00003E00
-#define SDR0_PFC0_GEIE_NOTRE 0x00000000
-#define SDR0_PFC0_TRE_MASK 0x00000100
-#define SDR0_PFC0_TRE_DISABLE 0x00000000
-#define SDR0_PFC0_TRE_ENABLE 0x00000100
-#define SDR0_PFC0_TRE_ENCODE(n) ((((unsigned long)(n))&0x01)<<8)
-#define SDR0_PFC0_TRE_DECODE(n) ((((unsigned long)(n))>>8)&0x01)
-
-#define SDR0_PFC1_UART1_DSR_CTS_MASK 0x02000000
-#define SDR0_PFC1_EPS_MASK 0x01C00000
-#define SDR0_PFC1_EPS_GROUP0 0x00000000
-#define SDR0_PFC1_EPS_GROUP1 0x00400000
-#define SDR0_PFC1_EPS_GROUP2 0x00800000
-#define SDR0_PFC1_EPS_GROUP3 0x00C00000
-#define SDR0_PFC1_EPS_GROUP4 0x01000000
-#define SDR0_PFC1_EPS_GROUP5 0x01400000
-#define SDR0_PFC1_EPS_GROUP6 0x01800000
-#define SDR0_PFC1_EPS_GROUP7 0x01C00000
-#define SDR0_PFC1_EPS_ENCODE(n) ((((unsigned long)(n))&0x07)<<22)
-#define SDR0_PFC1_EPS_DECODE(n) ((((unsigned long)(n))>>22)&0x07)
-#define SDR0_PFC1_RMII_MASK 0x00200000
-#define SDR0_PFC1_RMII_100MBIT 0x00000000
-#define SDR0_PFC1_RMII_10MBIT 0x00200000
-#define SDR0_PFC1_RMII_ENCODE(n) ((((unsigned long)(n))&0x01)<<21)
-#define SDR0_PFC1_RMII_DECODE(n) ((((unsigned long)(n))>>21)&0x01)
-#define SDR0_PFC1_CTEMS_MASK 0x00100000
-#define SDR0_PFC1_CTEMS_EMS 0x00000000
-#define SDR0_PFC1_CTEMS_CPUTRACE 0x00100000
-
-#define SDR0_MFR_TAH0_MASK 0x80000000
-#define SDR0_MFR_TAH0_ENABLE 0x00000000
-#define SDR0_MFR_TAH0_DISABLE 0x80000000
-#define SDR0_MFR_TAH1_MASK 0x40000000
-#define SDR0_MFR_TAH1_ENABLE 0x00000000
-#define SDR0_MFR_TAH1_DISABLE 0x40000000
-#define SDR0_MFR_PCM_MASK 0x20000000
-#define SDR0_MFR_PCM_PPC440GX 0x00000000
-#define SDR0_MFR_PCM_PPC440GP 0x20000000
-#define SDR0_MFR_ECS_MASK 0x10000000
-#define SDR0_MFR_ECS_INTERNAL 0x10000000
-
-#define SDR0_MFR_ETH0_CLK_SEL 0x08000000 /* Ethernet0 Clock Select */
-#define SDR0_MFR_ETH1_CLK_SEL 0x04000000 /* Ethernet1 Clock Select */
-#define SDR0_MFR_ZMII_MODE_MASK 0x03000000 /* ZMII Mode Mask */
-#define SDR0_MFR_ZMII_MODE_MII 0x00000000 /* ZMII Mode MII */
-#define SDR0_MFR_ZMII_MODE_SMII 0x01000000 /* ZMII Mode SMII */
-#define SDR0_MFR_ZMII_MODE_RMII_10M 0x02000000 /* ZMII Mode RMII - 10 Mbs */
-#define SDR0_MFR_ZMII_MODE_RMII_100M 0x03000000 /* ZMII Mode RMII - 100 Mbs*/
-#define SDR0_MFR_ZMII_MODE_BIT0 0x02000000 /* ZMII Mode Bit0 */
-#define SDR0_MFR_ZMII_MODE_BIT1 0x01000000 /* ZMII Mode Bit1 */
-#define SDR0_MFR_ERRATA3_EN0 0x00800000
-#define SDR0_MFR_ERRATA3_EN1 0x00400000
-#if defined(CONFIG_440GX) /* test-only: only 440GX or 440SPE??? */
-#define SDR0_MFR_PKT_REJ_MASK 0x00300000 /* Pkt Rej. Enable Mask */
-#define SDR0_MFR_PKT_REJ_EN 0x00300000 /* Pkt Rej. Enable on both EMAC3
- 0-1 */
-#define SDR0_MFR_PKT_REJ_EN0 0x00200000 /* Pkt Rej. Enable on EMAC3(0) */
-#define SDR0_MFR_PKT_REJ_EN1 0x00100000 /* Pkt Rej. Enable on EMAC3(1) */
-#define SDR0_MFR_PKT_REJ_POL 0x00080000 /* Packet Reject Polarity */
-#endif
-
-
-#if defined(CONFIG_440EPX)
-#define CPM0_ER 0x000000B0
-#define CPM1_ER 0x000000F0
-#define PLB4A0_ACR 0x00000081
-#define PLB4A1_ACR 0x00000089
-#define PLB3A0_ACR 0x00000077
-#define OPB2PLB40_BCTRL 0x00000350
-#define P4P3BO0_CFG 0x00000026
-#define SPI0_MODE 0xEF600090 /* SPI Mode Regsgiter */
-
-#endif
-
-#if defined(CONFIG_440EPX) || defined(CONFIG_440GRX)
-#define SDR0_PFC1_EPS_ENCODE(n) ((((unsigned long)(n))&0x07)<<22)
-#define SDR0_PFC1_EPS_DECODE(n) ((((unsigned long)(n))>>22)&0x07)
-#define SDR0_PFC2_EPS_ENCODE(n) ((((unsigned long)(n))&0x07)<<29)
-#define SDR0_PFC2_EPS_DECODE(n) ((((unsigned long)(n))>>29)&0x07)
-#endif
-
-#define SDR0_MFR_ECS_MASK 0x10000000
-#define SDR0_MFR_ECS_INTERNAL 0x10000000
-
-#if defined(CONFIG_440EPX) || defined(CONFIG_440GRX)
-#define SDR0_SRST0 0x200
-#define SDR0_SRST0_BGO 0x80000000 /* PLB to OPB bridge */
-#define SDR0_SRST0_PLB4 0x40000000 /* PLB4 arbiter */
-#define SDR0_SRST0_EBC 0x20000000 /* External bus controller */
-#define SDR0_SRST0_OPB 0x10000000 /* OPB arbiter */
-#define SDR0_SRST0_UART0 0x08000000 /* Universal asynchronous receiver/
- transmitter 0 */
-#define SDR0_SRST0_UART1 0x04000000 /* Universal asynchronous receiver/
- transmitter 1 */
-#define SDR0_SRST0_IIC0 0x02000000 /* Inter integrated circuit 0 */
-#define SDR0_SRST0_USB2H 0x01000000 /* USB2.0 Host */
-#define SDR0_SRST0_GPIO 0x00800000 /* General purpose I/O */
-#define SDR0_SRST0_GPT 0x00400000 /* General purpose timer */
-#define SDR0_SRST0_DMC 0x00200000 /* DDR SDRAM memory controller */
-#define SDR0_SRST0_PCI 0x00100000 /* PCI */
-#define SDR0_SRST0_EMAC0 0x00080000 /* Ethernet media access controller 0 */
-#define SDR0_SRST0_EMAC1 0x00040000 /* Ethernet media access controller 1 */
-#define SDR0_SRST0_CPM0 0x00020000 /* Clock and power management */
-#define SDR0_SRST0_ZMII 0x00010000 /* ZMII bridge */
-#define SDR0_SRST0_UIC0 0x00008000 /* Universal interrupt controller 0 */
-#define SDR0_SRST0_UIC1 0x00004000 /* Universal interrupt controller 1 */
-#define SDR0_SRST0_IIC1 0x00002000 /* Inter integrated circuit 1 */
-#define SDR0_SRST0_SCP 0x00001000 /* Serial communications port */
-#define SDR0_SRST0_BGI 0x00000800 /* OPB to PLB bridge */
-#define SDR0_SRST0_DMA 0x00000400 /* Direct memory access controller */
-#define SDR0_SRST0_DMAC 0x00000200 /* DMA channel */
-#define SDR0_SRST0_MAL 0x00000100 /* Media access layer */
-#define SDR0_SRST0_USB2D 0x00000080 /* USB2.0 device */
-#define SDR0_SRST0_GPTR 0x00000040 /* General purpose timer */
-#define SDR0_SRST0_P4P3 0x00000010 /* PLB4 to PLB3 bridge */
-#define SDR0_SRST0_P3P4 0x00000008 /* PLB3 to PLB4 bridge */
-#define SDR0_SRST0_PLB3 0x00000004 /* PLB3 arbiter */
-#define SDR0_SRST0_UART2 0x00000002 /* Universal asynchronous receiver/
- transmitter 2 */
-#define SDR0_SRST0_UART3 0x00000001 /* Universal asynchronous receiver/
- transmitter 3 */
-
-#define SDR0_SRST1 0x201
-#define SDR0_SRST1_NDFC 0x80000000 /* Nand flash controller */
-#define SDR0_SRST1_OPBA1 0x40000000 /* OPB Arbiter attached to PLB4 */
-#define SDR0_SRST1_P4OPB0 0x20000000 /* PLB4 to OPB Bridge0 */
-#define SDR0_SRST1_PLB42OPB0 SDR0_SRST1_P4OPB0
-#define SDR0_SRST1_DMA4 0x10000000 /* DMA to PLB4 */
-#define SDR0_SRST1_DMA4CH 0x08000000 /* DMA Channel to PLB4 */
-#define SDR0_SRST1_OPBA2 0x04000000 /* OPB Arbiter attached to PLB4
- USB 2.0 Host */
-#define SDR0_SRST1_OPB2PLB40 0x02000000 /* OPB to PLB4 Bridge attached to
- USB 2.0 Host */
-#define SDR0_SRST1_PLB42OPB1 0x01000000 /* PLB4 to OPB Bridge attached to
- USB 2.0 Host */
-#define SDR0_SRST1_CPM1 0x00800000 /* Clock and Power management 1 */
-#define SDR0_SRST1_UIC2 0x00400000 /* Universal Interrupt Controller 2*/
-#define SDR0_SRST1_CRYP0 0x00200000 /* Security Engine */
-#define SDR0_SRST1_USB20PHY 0x00100000 /* USB 2.0 Phy */
-#define SDR0_SRST1_USB2HUTMI 0x00080000 /* USB 2.0 Host UTMI Interface */
-#define SDR0_SRST1_USB2HPHY 0x00040000 /* USB 2.0 Host Phy Interface */
-#define SDR0_SRST1_SRAM0 0x00020000 /* Internal SRAM Controller */
-#define SDR0_SRST1_RGMII0 0x00010000 /* RGMII Bridge */
-#define SDR0_SRST1_ETHPLL 0x00008000 /* Ethernet PLL */
-#define SDR0_SRST1_FPU 0x00004000 /* Floating Point Unit */
-#define SDR0_SRST1_KASU0 0x00002000 /* Kasumi Engine */
-
-#define SDR0_EMAC0RXST 0x00004301 /* */
-#define SDR0_EMAC0TXST 0x00004302 /* */
-#define SDR0_CRYP0 0x00004500
-#define SDR0_EBC0 0x00000100
-#define SDR0_SDSTP2 0x00004001
-#define SDR0_SDSTP3 0x00004001
-#elif defined(CONFIG_460EX) || defined(CONFIG_460GT)
-
-#define SDR0_SRST0 SDR0_SRST /* for compatability reasons */
-#define SDR0_SRST0_BGO 0x80000000 /* PLB to OPB bridge */
-#define SDR0_SRST0_PLB4 0x40000000 /* PLB4 arbiter */
-#define SDR0_SRST0_EBC 0x20000000 /* External bus controller */
-#define SDR0_SRST0_OPB 0x10000000 /* OPB arbiter */
-#define SDR0_SRST0_UART0 0x08000000 /* Universal asynchronous receiver/
- transmitter 0 */
-#define SDR0_SRST0_UART1 0x04000000 /* Universal asynchronous receiver/
- transmitter 1 */
-#define SDR0_SRST0_IIC0 0x02000000 /* Inter integrated circuit 0 */
-#define SDR0_SRST0_IIC1 0x01000000 /* Inter integrated circuit 1 */
-#define SDR0_SRST0_GPIO0 0x00800000 /* General purpose I/O 0 */
-#define SDR0_SRST0_GPT 0x00400000 /* General purpose timer */
-#define SDR0_SRST0_DMC 0x00200000 /* DDR SDRAM memory controller */
-#define SDR0_SRST0_PCI 0x00100000 /* PCI */
-#define SDR0_SRST0_CPM0 0x00020000 /* Clock and power management */
-#define SDR0_SRST0_IMU 0x00010000 /* I2O DMA */
-#define SDR0_SRST0_UIC0 0x00008000 /* Universal interrupt controller 0*/
-#define SDR0_SRST0_UIC1 0x00004000 /* Universal interrupt controller 1*/
-#define SDR0_SRST0_SRAM 0x00002000 /* Universal interrupt controller 0*/
-#define SDR0_SRST0_UIC2 0x00001000 /* Universal interrupt controller 2*/
-#define SDR0_SRST0_UIC3 0x00000800 /* Universal interrupt controller 3*/
-#define SDR0_SRST0_OCM 0x00000400 /* Universal interrupt controller 0*/
-#define SDR0_SRST0_UART2 0x00000200 /* Universal asynchronous receiver/
- transmitter 2 */
-#define SDR0_SRST0_MAL 0x00000100 /* Media access layer */
-#define SDR0_SRST0_GPTR 0x00000040 /* General purpose timer */
-#define SDR0_SRST0_L2CACHE 0x00000004 /* L2 Cache */
-#define SDR0_SRST0_UART3 0x00000002 /* Universal asynchronous receiver/
- transmitter 3 */
-#define SDR0_SRST0_GPIO1 0x00000001 /* General purpose I/O 1 */
-
-#define SDR0_SRST1 0x201
-#define SDR0_SRST1_RLL 0x80000000 /* SRIO RLL */
-#define SDR0_SRST1_SCP 0x40000000 /* Serial communications port */
-#define SDR0_SRST1_PLBARB 0x20000000 /* PLB Arbiter */
-#define SDR0_SRST1_EIPPKP 0x10000000 /* EIPPPKP */
-#define SDR0_SRST1_EIP94 0x08000000 /* EIP 94 */
-#define SDR0_SRST1_EMAC0 0x04000000 /* Ethernet media access
- controller 0 */
-#define SDR0_SRST1_EMAC1 0x02000000 /* Ethernet media access
- controller 1 */
-#define SDR0_SRST1_EMAC2 0x01000000 /* Ethernet media access
- controller 2 */
-#define SDR0_SRST1_EMAC3 0x00800000 /* Ethernet media access
- controller 3 */
-#define SDR0_SRST1_ZMII 0x00400000 /* Ethernet ZMII/RMII/SMII */
-#define SDR0_SRST1_RGMII0 0x00200000 /* Ethernet RGMII/RTBI 0 */
-#define SDR0_SRST1_RGMII1 0x00100000 /* Ethernet RGMII/RTBI 1 */
-#define SDR0_SRST1_DMA4 0x00080000 /* DMA to PLB4 */
-#define SDR0_SRST1_DMA4CH 0x00040000 /* DMA Channel to PLB4 */
-#define SDR0_SRST1_SATAPHY 0x00020000 /* Serial ATA PHY */
-#define SDR0_SRST1_SRIODEV 0x00010000 /* Serial Rapid IO core, PCS, and
- serdes */
-#define SDR0_SRST1_SRIOPCS 0x00008000 /* Serial Rapid IO core and PCS */
-#define SDR0_SRST1_NDFC 0x00004000 /* Nand flash controller */
-#define SDR0_SRST1_SRIOPLB 0x00002000 /* Serial Rapid IO PLB */
-#define SDR0_SRST1_ETHPLL 0x00001000 /* Ethernet PLL */
-#define SDR0_SRST1_TAHOE1 0x00000800 /* Ethernet Tahoe 1 */
-#define SDR0_SRST1_TAHOE0 0x00000400 /* Ethernet Tahoe 0 */
-#define SDR0_SRST1_SGMII0 0x00000200 /* Ethernet SGMII 0 */
-#define SDR0_SRST1_SGMII1 0x00000100 /* Ethernet SGMII 1 */
-#define SDR0_SRST1_SGMII2 0x00000080 /* Ethernet SGMII 2 */
-#define SDR0_SRST1_AHB 0x00000040 /* PLB4XAHB bridge */
-#define SDR0_SRST1_USBOTGPHY 0x00000020 /* USB 2.0 OTG PHY */
-#define SDR0_SRST1_USBOTG 0x00000010 /* USB 2.0 OTG controller */
-#define SDR0_SRST1_USBHOST 0x00000008 /* USB 2.0 Host controller */
-#define SDR0_SRST1_AHBDMAC 0x00000004 /* AHB DMA controller */
-#define SDR0_SRST1_AHBICM 0x00000002 /* AHB inter-connect matrix */
-#define SDR0_SRST1_SATA 0x00000001 /* Serial ATA controller */
-
-#else
-
-#define SDR0_SRST_BGO 0x80000000
-#define SDR0_SRST_PLB 0x40000000
-#define SDR0_SRST_EBC 0x20000000
-#define SDR0_SRST_OPB 0x10000000
-#define SDR0_SRST_UART0 0x08000000
-#define SDR0_SRST_UART1 0x04000000
-#define SDR0_SRST_IIC0 0x02000000
-#define SDR0_SRST_IIC1 0x01000000
-#define SDR0_SRST_GPIO 0x00800000
-#define SDR0_SRST_GPT 0x00400000
-#define SDR0_SRST_DMC 0x00200000
-#define SDR0_SRST_PCI 0x00100000
-#define SDR0_SRST_EMAC0 0x00080000
-#define SDR0_SRST_EMAC1 0x00040000
-#define SDR0_SRST_CPM 0x00020000
-#define SDR0_SRST_IMU 0x00010000
-#define SDR0_SRST_UIC01 0x00008000
-#define SDR0_SRST_UICB2 0x00004000
-#define SDR0_SRST_SRAM 0x00002000
-#define SDR0_SRST_EBM 0x00001000
-#define SDR0_SRST_BGI 0x00000800
-#define SDR0_SRST_DMA 0x00000400
-#define SDR0_SRST_DMAC 0x00000200
-#define SDR0_SRST_MAL 0x00000100
-#define SDR0_SRST_ZMII 0x00000080
-#define SDR0_SRST_GPTR 0x00000040
-#define SDR0_SRST_PPM 0x00000020
-#define SDR0_SRST_EMAC2 0x00000010
-#define SDR0_SRST_EMAC3 0x00000008
-#define SDR0_SRST_RGMII 0x00000001
-
-#endif
-
-/*-----------------------------------------------------------------------------+
-| Clocking
-+-----------------------------------------------------------------------------*/
-#if defined(CONFIG_460EX) || defined(CONFIG_460GT) || \
- defined(CONFIG_460SX)
-#define PLLSYS0_FWD_DIV_A_MASK 0x000000f0 /* Fwd Div A */
-#define PLLSYS0_FWD_DIV_B_MASK 0x0000000f /* Fwd Div B */
-#define PLLSYS0_FB_DIV_MASK 0x0000ff00 /* Feedback divisor */
-#define PLLSYS0_OPB_DIV_MASK 0x0c000000 /* OPB Divisor */
-#define PLLSYS0_PLBEDV0_DIV_MASK 0xe0000000 /* PLB Early Clock Divisor */
-#define PLLSYS0_PERCLK_DIV_MASK 0x03000000 /* Peripheral Clk Divisor */
-#define PLLSYS0_SEL_MASK 0x18000000 /* 0 = PLL, 1 = PerClk */
-#elif !defined (CONFIG_440GX) && \
- !defined(CONFIG_440EP) && !defined(CONFIG_440GR) && \
- !defined(CONFIG_440EPX) && !defined(CONFIG_440GRX) && \
- !defined(CONFIG_440SP) && !defined(CONFIG_440SPE)
-#define PLLSYS0_TUNE_MASK 0xffc00000 /* PLL TUNE bits */
-#define PLLSYS0_FB_DIV_MASK 0x003c0000 /* Feedback divisor */
-#define PLLSYS0_FWD_DIV_A_MASK 0x00038000 /* Forward divisor A */
-#define PLLSYS0_FWD_DIV_B_MASK 0x00007000 /* Forward divisor B */
-#define PLLSYS0_OPB_DIV_MASK 0x00000c00 /* OPB divisor */
-#define PLLSYS0_EPB_DIV_MASK 0x00000300 /* EPB divisor */
-#define PLLSYS0_EXTSL_MASK 0x00000080 /* PerClk feedback path */
-#define PLLSYS0_RW_MASK 0x00000060 /* ROM width */
-#define PLLSYS0_RL_MASK 0x00000010 /* ROM location */
-#define PLLSYS0_ZMII_SEL_MASK 0x0000000c /* ZMII selection */
-#define PLLSYS0_BYPASS_MASK 0x00000002 /* Bypass PLL */
-#define PLLSYS0_NTO1_MASK 0x00000001 /* CPU:PLB N-to-1 ratio */
-
-#define PLL_VCO_FREQ_MIN 500 /* Min VCO freq (MHz) */
-#define PLL_VCO_FREQ_MAX 1000 /* Max VCO freq (MHz) */
-#define PLL_CPU_FREQ_MAX 400 /* Max CPU freq (MHz) */
-#define PLL_PLB_FREQ_MAX 133 /* Max PLB freq (MHz) */
-#else /* !CONFIG_440GX or CONFIG_440EP or CONFIG_440GR */
-#define PLLSYS0_ENG_MASK 0x80000000 /* 0 = SysClk, 1 = PLL VCO */
-#define PLLSYS0_SRC_MASK 0x40000000 /* 0 = PLL A, 1 = PLL B */
-#define PLLSYS0_SEL_MASK 0x38000000 /* 0 = PLL, 1 = CPU, 5 = PerClk */
-#define PLLSYS0_TUNE_MASK 0x07fe0000 /* PLL Tune bits */
-#define PLLSYS0_FB_DIV_MASK 0x0001f000 /* Feedback divisor */
-#define PLLSYS0_FWD_DIV_A_MASK 0x00000f00 /* Fwd Div A */
-#define PLLSYS0_FWD_DIV_B_MASK 0x000000e0 /* Fwd Div B */
-#define PLLSYS0_PRI_DIV_B_MASK 0x0000001c /* PLL Primary Divisor B */
-#define PLLSYS0_OPB_DIV_MASK 0x00000003 /* OPB Divisor */
-
-#define PLLC_ENG_MASK 0x20000000 /* PLL primary forward divisor source */
-#define PLLC_SRC_MASK 0x20000000 /* PLL feedback source */
-#define PLLD_FBDV_MASK 0x1f000000 /* PLL Feedback Divisor */
-#define PLLD_FWDVA_MASK 0x000f0000 /* PLL Forward Divisor A */
-#define PLLD_FWDVB_MASK 0x00000700 /* PLL Forward Divisor B */
-#define PLLD_LFBDV_MASK 0x0000003f /* PLL Local Feedback Divisor */
-
-#define OPBDDV_MASK 0x03000000 /* OPB Clock Divisor Register */
-#define PERDV_MASK 0x07000000 /* Periferal Clock Divisor */
-#define PRADV_MASK 0x07000000 /* Primary Divisor A */
-#define PRBDV_MASK 0x07000000 /* Primary Divisor B */
-#define SPCID_MASK 0x03000000 /* Sync PCI Divisor */
-
-#define PLL_VCO_FREQ_MIN 500 /* Min VCO freq (MHz) */
-#define PLL_VCO_FREQ_MAX 1000 /* Max VCO freq (MHz) */
-#define PLL_CPU_FREQ_MAX 400 /* Max CPU freq (MHz) */
-#define PLL_PLB_FREQ_MAX 133 /* Max PLB freq (MHz) */
-
-/* Strap 1 Register */
-#define PLLSYS1_LF_DIV_MASK 0xfc000000 /* PLL Local Feedback Divisor */
-#define PLLSYS1_PERCLK_DIV_MASK 0x03000000 /* Peripheral Clk Divisor */
-#define PLLSYS1_MAL_DIV_MASK 0x00c00000 /* MAL Clk Divisor */
-#define PLLSYS1_RW_MASK 0x00300000 /* ROM width */
-#define PLLSYS1_EAR_MASK 0x00080000 /* ERAP Addres reset vector */
-#define PLLSYS1_PAE_MASK 0x00040000 /* PCI arbitor enable */
-#define PLLSYS1_PCHE_MASK 0x00020000 /* PCI host config enable */
-#define PLLSYS1_PISE_MASK 0x00010000 /* PCI init seq. enable */
-#define PLLSYS1_PCWE_MASK 0x00008000 /* PCI local cpu wait enable */
-#define PLLSYS1_PPIM_MASK 0x00007800 /* PCI inbound map */
-#define PLLSYS1_PR64E_MASK 0x00000400 /* PCI init Req64 enable */
-#define PLLSYS1_PXFS_MASK 0x00000300 /* PCI-X Freq Sel */
-#define PLLSYS1_RSVD_MASK 0x00000080 /* RSVD */
-#define PLLSYS1_PDM_MASK 0x00000040 /* PCI-X Driver Mode */
-#define PLLSYS1_EPS_MASK 0x00000038 /* Ethernet Pin Select */
-#define PLLSYS1_RMII_MASK 0x00000004 /* RMII Mode */
-#define PLLSYS1_TRE_MASK 0x00000002 /* GPIO Trace Enable */
-#define PLLSYS1_NTO1_MASK 0x00000001 /* CPU:PLB N-to-1 ratio */
-#endif /* CONFIG_440GX */
-
-#if defined(CONFIG_440EP) || defined(CONFIG_440GR) || \
- defined(CONFIG_440EPX) || defined(CONFIG_440GRX)
-#define CPR0_ICFG_RLI_MASK 0x80000000
-#define CPR0_ICFG_ICS_MASK 0x00000007
-#define CPR0_SPCID_SPCIDV0_MASK 0x03000000
-#define CPR0_SPCID_SPCIDV0_DIV1 0x01000000
-#define CPR0_SPCID_SPCIDV0_DIV2 0x02000000
-#define CPR0_SPCID_SPCIDV0_DIV3 0x03000000
-#define CPR0_SPCID_SPCIDV0_DIV4 0x00000000
-#define CPR0_PERD_PERDV0_MASK 0x07000000
-#endif
-
-#if defined(CONFIG_460EX) || defined(CONFIG_460GT)
-#define CPR0_ICFG_RLI_MASK 0x80000000
-
-#define CPR0_PLLC_RST 0x80000000
-#define CPR0_PLLC_ENG 0x40000000
-#endif
-
-/*-----------------------------------------------------------------------------
-| PCI Internal Registers et. al. (accessed via plb)
-+----------------------------------------------------------------------------*/
-#define PCIL0_CFGADR (CONFIG_SYS_PCI_BASE + 0x0ec00000)
-#define PCIL0_CFGDATA (CONFIG_SYS_PCI_BASE + 0x0ec00004)
-#define PCIL0_CFGBASE (CONFIG_SYS_PCI_BASE + 0x0ec80000)
-#define PCIL0_IOBASE (CONFIG_SYS_PCI_BASE + 0x08000000)
-
-#if defined(CONFIG_440EP) || defined(CONFIG_440GR) || \
- defined(CONFIG_440EPX) || defined(CONFIG_440GRX)
-
-/* PCI Local Configuration Registers
- --------------------------------- */
-#define PCI_MMIO_LCR_BASE (CONFIG_SYS_PCI_BASE + 0x0f400000) /* Real =>
- 0x0EF400000 */
-
-/* PCI Master Local Configuration Registers */
-#define PCIL0_PMM0LA (PCI_MMIO_LCR_BASE + 0x00) /* PMM0 Local Address */
-#define PCIL0_PMM0MA (PCI_MMIO_LCR_BASE + 0x04) /* PMM0 Mask/Attribute */
-#define PCIL0_PMM0PCILA (PCI_MMIO_LCR_BASE + 0x08) /* PMM0 PCI Low Address */
-#define PCIL0_PMM0PCIHA (PCI_MMIO_LCR_BASE + 0x0C) /* PMM0 PCI High Address */
-#define PCIL0_PMM1LA (PCI_MMIO_LCR_BASE + 0x10) /* PMM1 Local Address */
-#define PCIL0_PMM1MA (PCI_MMIO_LCR_BASE + 0x14) /* PMM1 Mask/Attribute */
-#define PCIL0_PMM1PCILA (PCI_MMIO_LCR_BASE + 0x18) /* PMM1 PCI Low Address */
-#define PCIL0_PMM1PCIHA (PCI_MMIO_LCR_BASE + 0x1C) /* PMM1 PCI High Address */
-#define PCIL0_PMM2LA (PCI_MMIO_LCR_BASE + 0x20) /* PMM2 Local Address */
-#define PCIL0_PMM2MA (PCI_MMIO_LCR_BASE + 0x24) /* PMM2 Mask/Attribute */
-#define PCIL0_PMM2PCILA (PCI_MMIO_LCR_BASE + 0x28) /* PMM2 PCI Low Address */
-#define PCIL0_PMM2PCIHA (PCI_MMIO_LCR_BASE + 0x2C) /* PMM2 PCI High Address */
-
-/* PCI Target Local Configuration Registers */
-#define PCIL0_PTM1MS (PCI_MMIO_LCR_BASE + 0x30) /* PTM1 Memory Size/
- Attribute */
-#define PCIL0_PTM1LA (PCI_MMIO_LCR_BASE + 0x34) /* PTM1 Local Addr. Reg */
-#define PCIL0_PTM2MS (PCI_MMIO_LCR_BASE + 0x38) /* PTM2 Memory Size/
- Attribute */
-#define PCIL0_PTM2LA (PCI_MMIO_LCR_BASE + 0x3C) /* PTM2 Local Addr. Reg */
-
-#else
-
+/* todo: move this code from macro offsets to struct */
#define PCIL0_VENDID (PCIL0_CFGBASE + PCI_VENDOR_ID )
#define PCIL0_DEVID (PCIL0_CFGBASE + PCI_DEVICE_ID )
#define PCIL0_CMD (PCIL0_CFGBASE + PCI_COMMAND )
@@ -1793,37 +183,10 @@
#define PCIL0_RES2 (PCIL0_CFGBASE + 0x0038 )
#define PCIL0_INTLN (PCIL0_CFGBASE + PCI_INTERRUPT_LINE )
#define PCIL0_INTPN (PCIL0_CFGBASE + PCI_INTERRUPT_PIN )
-#define SDR0_EMACxTXST_FUR 0x02000000 /* TX FIFO underrun */
-#define SDR0_EMACxTXST_BC 0x01000000 /* broadcase address */
-#define SDR0_EMACxTXST_MC 0x00800000 /* multicast address */
-#define SDR0_EMACxTXST_UC 0x00400000 /* unicast address */
-#define SDR0_EMACxTXST_FP 0x00200000 /* frame paused by control packet */
-#define SDR0_EMACxTXST_BFCS 0x00100000 /* bad FCS in the transmitted frame*/
-#define SDR0_EMACxTXST_CPF 0x00080000 /* TX control pause frame */
-#define SDR0_EMACxTXST_CF 0x00040000 /* TX control frame */
-#define SDR0_EMACxTXST_MSIZ 0x00020000 /* 1024-maxsize bytes transmitted */
-#define SDR0_EMACxTXST_1023 0x00010000 /* 512-1023 bytes transmitted */
-#define SDR0_EMACxTXST_511 0x00008000 /* 256-511 bytes transmitted */
-#define SDR0_EMACxTXST_255 0x00004000 /* 128-255 bytes transmitted */
-#define SDR0_EMACxTXST_127 0x00002000 /* 65-127 bytes transmitted */
-#define SDR0_EMACxTXST_64 0x00001000 /* 64 bytes transmitted */
-#define SDR0_EMACxTXST_SQE 0x00000800 /* SQE indication */
-#define SDR0_EMACxTXST_LOC 0x00000400 /* loss of carrier sense */
-#define SDR0_EMACxTXST_IERR 0x00000080 /* EMAC internal error */
-#define SDR0_EMACxTXST_EDF 0x00000040 /* excessive deferral */
-#define SDR0_EMACxTXST_ECOL 0x00000020 /* excessive collisions */
-#define SDR0_EMACxTXST_LCOL 0x00000010 /* late collision */
-#define SDR0_EMACxTXST_DFFR 0x00000008 /* deferred frame */
-#define SDR0_EMACxTXST_MCOL 0x00000004 /* multiple collision frame */
-#define SDR0_EMACxTXST_SCOL 0x00000002 /* single collision frame */
-#define SDR0_EMACxTXST_TXOK 0x00000001 /* transmit OK */
#define PCIL0_MINGNT (PCIL0_CFGBASE + PCI_MIN_GNT )
#define PCIL0_MAXLTNCY (PCIL0_CFGBASE + PCI_MAX_LAT )
-#define PCIL0_BRDGOPT1 (PCIL0_CFGBASE + 0x0040)
-#define PCIL0_BRDGOPT2 (PCIL0_CFGBASE + 0x0044)
-
#define PCIL0_POM0LAL (PCIL0_CFGBASE + 0x0068)
#define PCIL0_POM0LAH (PCIL0_CFGBASE + 0x006c)
#define PCIL0_POM0SA (PCIL0_CFGBASE + 0x0070)
@@ -1848,111 +211,44 @@
#define PCIL0_STS (PCIL0_CFGBASE + 0x00e0)
-#endif /* !defined(CONFIG_440EP) !defined(CONFIG_440GR) */
-
-#if defined(CONFIG_440EPX) || defined(CONFIG_440GRX)
-
-/* USB2.0 Device */
-#define USB2D0_BASE CONFIG_SYS_USB2D0_BASE
-
-#define USB2D0_INTRIN (USB2D0_BASE + 0x00000000)
-
-#define USB2D0_INTRIN (USB2D0_BASE + 0x00000000) /* Interrupt register for
- Endpoint 0 plus IN Endpoints 1 to 3 */
-#define USB2D0_POWER (USB2D0_BASE + 0x00000000) /* Power management
- register */
-#define USB2D0_FADDR (USB2D0_BASE + 0x00000000) /* Function address
- register */
-#define USB2D0_INTRINE (USB2D0_BASE + 0x00000000) /* Interrupt enable
- register for USB2D0_INTRIN */
-#define USB2D0_INTROUT (USB2D0_BASE + 0x00000000) /* Interrupt register for
- OUT Endpoints 1 to 3 */
-#define USB2D0_INTRUSBE (USB2D0_BASE + 0x00000000) /* Interrupt enable
- register for USB2D0_INTRUSB */
-#define USB2D0_INTRUSB (USB2D0_BASE + 0x00000000) /* Interrupt register for
- common USB interrupts */
-#define USB2D0_INTROUTE (USB2D0_BASE + 0x00000000) /* Interrupt enable
- register for IntrOut */
-#define USB2D0_TSTMODE (USB2D0_BASE + 0x00000000) /* Enables the USB 2.0
- test modes */
-#define USB2D0_INDEX (USB2D0_BASE + 0x00000000) /* Index register for
- selecting the Endpoint status/control registers */
-#define USB2D0_FRAME (USB2D0_BASE + 0x00000000) /* Frame number */
-#define USB2D0_INCSR0 (USB2D0_BASE + 0x00000000) /* Control Status
- register for Endpoint 0. (Index register set to select Endpoint 0) */
-#define USB2D0_INCSR (USB2D0_BASE + 0x00000000) /* Control Status
- register for IN Endpoint. (Index register set to select Endpoints 13) */
-#define USB2D0_INMAXP (USB2D0_BASE + 0x00000000) /* Maximum packet
- size for IN Endpoint. (Index register set to select Endpoints 13) */
-#define USB2D0_OUTCSR (USB2D0_BASE + 0x00000000) /* Control Status
- register for OUT Endpoint. (Index register set to select Endpoints 13) */
-#define USB2D0_OUTMAXP (USB2D0_BASE + 0x00000000) /* Maximum packet
- size for OUT Endpoint. (Index register set to select Endpoints 13) */
-#define USB2D0_OUTCOUNT0 (USB2D0_BASE + 0x00000000) /* Number of received
- bytes in Endpoint 0 FIFO. (Index register set to select Endpoint 0) */
-#define USB2D0_OUTCOUNT (USB2D0_BASE + 0x00000000) /* Number of bytes in
- OUT Endpoint FIFO. (Index register set to select Endpoints 13) */
-#endif
-
-/******************************************************************************
+/*
* GPIO macro register defines
- ******************************************************************************/
-#if defined(CONFIG_440GP) || defined(CONFIG_440GX) || \
- defined(CONFIG_440SP) || defined(CONFIG_440SPE) || \
- defined(CONFIG_460SX)
-#define GPIO0_BASE (CONFIG_SYS_PERIPHERAL_BASE+0x00000700)
+ */
+/* todo: move to ppc4xx.h and merge with gpio.h header */
+#define GPIO0_OR (GPIO0_BASE + 0x0)
+#define GPIO0_TCR (GPIO0_BASE + 0x4)
+#define GPIO0_OSRL (GPIO0_BASE + 0x8)
+#define GPIO0_OSRH (GPIO0_BASE + 0xC)
+#define GPIO0_TSRL (GPIO0_BASE + 0x10)
+#define GPIO0_TSRH (GPIO0_BASE + 0x14)
+#define GPIO0_ODR (GPIO0_BASE + 0x18)
+#define GPIO0_IR (GPIO0_BASE + 0x1C)
+#define GPIO0_RR1 (GPIO0_BASE + 0x20)
+#define GPIO0_RR2 (GPIO0_BASE + 0x24)
+#define GPIO0_RR3 (GPIO0_BASE + 0x28)
+#define GPIO0_ISR1L (GPIO0_BASE + 0x30)
+#define GPIO0_ISR1H (GPIO0_BASE + 0x34)
+#define GPIO0_ISR2L (GPIO0_BASE + 0x38)
+#define GPIO0_ISR2H (GPIO0_BASE + 0x3C)
+#define GPIO0_ISR3L (GPIO0_BASE + 0x40)
+#define GPIO0_ISR3H (GPIO0_BASE + 0x44)
-#define GPIO0_OR (GPIO0_BASE+0x0)
-#define GPIO0_TCR (GPIO0_BASE+0x4)
-#define GPIO0_ODR (GPIO0_BASE+0x18)
-#define GPIO0_IR (GPIO0_BASE+0x1C)
-#endif /* CONFIG_440GP */
-
-#if defined(CONFIG_440EP) || defined(CONFIG_440GR) || \
- defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \
- defined(CONFIG_460EX) || defined(CONFIG_460GT)
-#define GPIO0_BASE (CONFIG_SYS_PERIPHERAL_BASE+0x00000B00)
-#define GPIO1_BASE (CONFIG_SYS_PERIPHERAL_BASE+0x00000C00)
-
-#define GPIO0_OR (GPIO0_BASE+0x0)
-#define GPIO0_TCR (GPIO0_BASE+0x4)
-#define GPIO0_OSRL (GPIO0_BASE+0x8)
-#define GPIO0_OSRH (GPIO0_BASE+0xC)
-#define GPIO0_TSRL (GPIO0_BASE+0x10)
-#define GPIO0_TSRH (GPIO0_BASE+0x14)
-#define GPIO0_ODR (GPIO0_BASE+0x18)
-#define GPIO0_IR (GPIO0_BASE+0x1C)
-#define GPIO0_RR1 (GPIO0_BASE+0x20)
-#define GPIO0_RR2 (GPIO0_BASE+0x24)
-#define GPIO0_RR3 (GPIO0_BASE+0x28)
-#define GPIO0_ISR1L (GPIO0_BASE+0x30)
-#define GPIO0_ISR1H (GPIO0_BASE+0x34)
-#define GPIO0_ISR2L (GPIO0_BASE+0x38)
-#define GPIO0_ISR2H (GPIO0_BASE+0x3C)
-#define GPIO0_ISR3L (GPIO0_BASE+0x40)
-#define GPIO0_ISR3H (GPIO0_BASE+0x44)
-
-#define GPIO1_OR (GPIO1_BASE+0x0)
-#define GPIO1_TCR (GPIO1_BASE+0x4)
-#define GPIO1_OSRL (GPIO1_BASE+0x8)
-#define GPIO1_OSRH (GPIO1_BASE+0xC)
-#define GPIO1_TSRL (GPIO1_BASE+0x10)
-#define GPIO1_TSRH (GPIO1_BASE+0x14)
-#define GPIO1_ODR (GPIO1_BASE+0x18)
-#define GPIO1_IR (GPIO1_BASE+0x1C)
-#define GPIO1_RR1 (GPIO1_BASE+0x20)
-#define GPIO1_RR2 (GPIO1_BASE+0x24)
-#define GPIO1_RR3 (GPIO1_BASE+0x28)
-#define GPIO1_ISR1L (GPIO1_BASE+0x30)
-#define GPIO1_ISR1H (GPIO1_BASE+0x34)
-#define GPIO1_ISR2L (GPIO1_BASE+0x38)
-#define GPIO1_ISR2H (GPIO1_BASE+0x3C)
-#define GPIO1_ISR3L (GPIO1_BASE+0x40)
-#define GPIO1_ISR3H (GPIO1_BASE+0x44)
-#endif
-
-#ifndef __ASSEMBLY__
-
-#endif /* _ASMLANGUAGE */
+#define GPIO1_OR (GPIO1_BASE + 0x0)
+#define GPIO1_TCR (GPIO1_BASE + 0x4)
+#define GPIO1_OSRL (GPIO1_BASE + 0x8)
+#define GPIO1_OSRH (GPIO1_BASE + 0xC)
+#define GPIO1_TSRL (GPIO1_BASE + 0x10)
+#define GPIO1_TSRH (GPIO1_BASE + 0x14)
+#define GPIO1_ODR (GPIO1_BASE + 0x18)
+#define GPIO1_IR (GPIO1_BASE + 0x1C)
+#define GPIO1_RR1 (GPIO1_BASE + 0x20)
+#define GPIO1_RR2 (GPIO1_BASE + 0x24)
+#define GPIO1_RR3 (GPIO1_BASE + 0x28)
+#define GPIO1_ISR1L (GPIO1_BASE + 0x30)
+#define GPIO1_ISR1H (GPIO1_BASE + 0x34)
+#define GPIO1_ISR2L (GPIO1_BASE + 0x38)
+#define GPIO1_ISR2H (GPIO1_BASE + 0x3C)
+#define GPIO1_ISR3L (GPIO1_BASE + 0x40)
+#define GPIO1_ISR3H (GPIO1_BASE + 0x44)
#endif /* __PPC440_H__ */
diff --git a/arch/powerpc/include/asm/ppc440ep_gr.h b/arch/powerpc/include/asm/ppc440ep_gr.h
new file mode 100644
index 0000000..2535787
--- /dev/null
+++ b/arch/powerpc/include/asm/ppc440ep_gr.h
@@ -0,0 +1,236 @@
+/*
+ * (C) Copyright 2010
+ * Stefan Roese, DENX Software Engineering, sr@denx.de.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef _PPC440EP_GR_H_
+#define _PPC440EP_GR_H_
+
+#define CONFIG_SDRAM_PPC4xx_IBM_DDR /* IBM DDR controller */
+
+#define CONFIG_NAND_NDFC
+
+#define CONFIG_SYS_PPC4xx_PLB4_ARBITER
+
+/*
+ * Some SoC specific registers (not common for all 440 SoC's)
+ */
+#define GPIO0_BASE (CONFIG_SYS_PERIPHERAL_BASE + 0x00000B00)
+#define GPIO1_BASE (CONFIG_SYS_PERIPHERAL_BASE + 0x00000C00)
+
+#define SDR0_PCI0 0x0300
+#define SDR0_SDSTP2 0x4001
+#define SDR0_SDSTP3 0x4003
+
+#define SDR0_SDSTP1_PAE_MASK (0x80000000 >> 21)
+#define SDR0_SDSTP1_PAME_MASK (0x80000000 >> 27)
+
+/* Pin Function Control Register 1 */
+#define SDR0_PFC1_U1ME_MASK 0x02000000 /* UART1 Mode Enable */
+#define SDR0_PFC1_U1ME_DSR_DTR 0x00000000 /* UART1 in DSR/DTR Mode */
+#define SDR0_PFC1_U1ME_CTS_RTS 0x02000000 /* UART1 in CTS/RTS Mode */
+#define SDR0_PFC1_U0ME_MASK 0x00080000 /* UART0 Mode Enable */
+#define SDR0_PFC1_U0ME_DSR_DTR 0x00000000 /* UART0 in DSR/DTR Mode */
+#define SDR0_PFC1_U0ME_CTS_RTS 0x00080000 /* UART0 in CTS/RTS Mode */
+#define SDR0_PFC1_U0IM_MASK 0x00040000 /* UART0 Interface Mode */
+#define SDR0_PFC1_U0IM_8PINS 0x00000000 /* UART0 Interface Mode 8 pins */
+#define SDR0_PFC1_U0IM_4PINS 0x00040000 /* UART0 Interface Mode 4 pins */
+#define SDR0_PFC1_SIS_MASK 0x00020000 /* SCP or IIC1 Selection */
+#define SDR0_PFC1_SIS_SCP_SEL 0x00000000 /* SCP Selected */
+#define SDR0_PFC1_SIS_IIC1_SEL 0x00020000 /* IIC1 Selected */
+#define SDR0_PFC1_UES_MASK 0x00010000 /* USB2D_RX_Active / EBC_Hold
+ Req Selection */
+#define SDR0_PFC1_UES_USB2D_SEL 0x00000000 /* USB2D_RX_Active Selected */
+#define SDR0_PFC1_UES_EBCHR_SEL 0x00010000 /* EBC_Hold Req Selected */
+#define SDR0_PFC1_DIS_MASK 0x00008000 /* DMA_Req(1) / UIC_IRQ(5)
+ Selection */
+#define SDR0_PFC1_DIS_DMAR_SEL 0x00000000 /* DMA_Req(1) Selected */
+#define SDR0_PFC1_DIS_UICIRQ5_SEL 0x00008000 /* UIC_IRQ(5) Selected */
+#define SDR0_PFC1_ERE_MASK 0x00004000 /* EBC Mast.Ext.Req.En./GPIO0(27)
+ Selection */
+#define SDR0_PFC1_ERE_EXTR_SEL 0x00000000 /* EBC Mast.Ext.Req.En.
+ Selected */
+#define SDR0_PFC1_ERE_GPIO0_27_SEL 0x00004000 /* GPIO0(27) Selected */
+#define SDR0_PFC1_UPR_MASK 0x00002000 /* USB2 Device Packet Reject
+ Selection */
+#define SDR0_PFC1_UPR_DISABLE 0x00000000 /* USB2 Device Packet Reject
+ Disable */
+#define SDR0_PFC1_UPR_ENABLE 0x00002000 /* USB2 Device Packet Reject
+ Enable */
+#define SDR0_PFC1_PLB_PME_MASK 0x00001000 /* PLB3/PLB4 Perf. Monitor Enable
+ Selection */
+#define SDR0_PFC1_PLB_PME_PLB3_SEL 0x00000000 /* PLB3 Performance Monitor
+ Enable */
+#define SDR0_PFC1_PLB_PME_PLB4_SEL 0x00001000 /* PLB3 Performance Monitor
+ Enable */
+#define SDR0_PFC1_GFGGI_MASK 0x0000000F /* GPT Frequency Generation
+ Gated In */
+
+/* USB Control Register */
+#define SDR0_USB0_USB_DEVSEL_MASK 0x00000002 /* USB Device Selection */
+#define SDR0_USB0_USB20D_DEVSEL 0x00000000 /* USB2.0 Device Selected */
+#define SDR0_USB0_USB11D_DEVSEL 0x00000002 /* USB1.1 Device Selected */
+#define SDR0_USB0_LEEN_MASK 0x00000001 /* Little Endian selection */
+#define SDR0_USB0_LEEN_DISABLE 0x00000000 /* Little Endian Disable */
+#define SDR0_USB0_LEEN_ENABLE 0x00000001 /* Little Endian Enable */
+
+/* Miscealleneaous Function Reg. */
+#define SDR0_MFR_ETH0_CLK_SEL_MASK 0x08000000 /* Ethernet0 Clock Select */
+#define SDR0_MFR_ETH0_CLK_SEL_EXT 0x00000000
+#define SDR0_MFR_ETH1_CLK_SEL_MASK 0x04000000 /* Ethernet1 Clock Select */
+#define SDR0_MFR_ETH1_CLK_SEL_EXT 0x00000000
+#define SDR0_MFR_ZMII_MODE_MASK 0x03000000 /* ZMII Mode Mask */
+#define SDR0_MFR_ZMII_MODE_MII 0x00000000 /* ZMII Mode MII */
+#define SDR0_MFR_ZMII_MODE_SMII 0x01000000 /* ZMII Mode SMII */
+#define SDR0_MFR_ZMII_MODE_RMII_10M 0x02000000 /* ZMII Mode RMII - 10 Mbs */
+#define SDR0_MFR_ZMII_MODE_RMII_100M 0x03000000 /* ZMII Mode RMII - 100 Mbs */
+#define SDR0_MFR_ZMII_MODE_BIT0 0x02000000 /* ZMII Mode Bit0 */
+#define SDR0_MFR_ZMII_MODE_BIT1 0x01000000 /* ZMII Mode Bit1 */
+#define SDR0_MFR_ZM_ENCODE(n) ((((u32)(n)) & 0x3) << 24)
+#define SDR0_MFR_ZM_DECODE(n) ((((u32)(n)) << 24) & 0x3)
+
+#define SDR0_MFR_ERRATA3_EN0 0x00800000
+#define SDR0_MFR_ERRATA3_EN1 0x00400000
+#define SDR0_MFR_PKT_REJ_MASK 0x00180000 /* Pkt Rej. Enable Mask */
+#define SDR0_MFR_PKT_REJ_EN 0x00180000 /* Pkt Rej. Ena. on both EMAC3 0-1 */
+#define SDR0_MFR_PKT_REJ_EN0 0x00100000 /* Pkt Rej. Enable on EMAC3(0) */
+#define SDR0_MFR_PKT_REJ_EN1 0x00080000 /* Pkt Rej. Enable on EMAC3(1) */
+#define SDR0_MFR_PKT_REJ_POL 0x00200000 /* Packet Reject Polarity */
+
+/* CUST0 Customer Configuration Register0 */
+#define SDR0_CUST0_MUX_E_N_G_MASK 0xC0000000 /* Mux_Emac_NDFC_GPIO */
+#define SDR0_CUST0_MUX_EMAC_SEL 0x40000000 /* Emac Selection */
+#define SDR0_CUST0_MUX_NDFC_SEL 0x80000000 /* NDFC Selection */
+#define SDR0_CUST0_MUX_GPIO_SEL 0xC0000000 /* GPIO Selection */
+
+#define SDR0_CUST0_NDFC_EN_MASK 0x20000000 /* NDFC Enable Mask */
+#define SDR0_CUST0_NDFC_ENABLE 0x20000000 /* NDFC Enable */
+#define SDR0_CUST0_NDFC_DISABLE 0x00000000 /* NDFC Disable */
+
+#define SDR0_CUST0_NDFC_BW_MASK 0x10000000 /* NDFC Boot Width */
+#define SDR0_CUST0_NDFC_BW_16_BIT 0x10000000 /* NDFC Boot Width = 16 Bit */
+#define SDR0_CUST0_NDFC_BW_8_BIT 0x00000000 /* NDFC Boot Width = 8 Bit */
+
+#define SDR0_CUST0_NDFC_BP_MASK 0x0F000000 /* NDFC Boot Page */
+#define SDR0_CUST0_NDFC_BP_ENCODE(n) ((((u32)(n)) & 0xF) << 24)
+#define SDR0_CUST0_NDFC_BP_DECODE(n) ((((u32)(n)) >> 24) & 0xF)
+
+#define SDR0_CUST0_NDFC_BAC_MASK 0x00C00000 /* NDFC Boot Address Cycle */
+#define SDR0_CUST0_NDFC_BAC_ENCODE(n) ((((u32)(n)) & 0x3) << 22)
+#define SDR0_CUST0_NDFC_BAC_DECODE(n) ((((u32)(n)) >> 22) & 0x3)
+
+#define SDR0_CUST0_NDFC_ARE_MASK 0x00200000 /* NDFC Auto Read Enable */
+#define SDR0_CUST0_NDFC_ARE_ENABLE 0x00200000 /* NDFC Auto Read Enable */
+#define SDR0_CUST0_NDFC_ARE_DISABLE 0x00000000 /* NDFC Auto Read Disable */
+
+#define SDR0_CUST0_NRB_MASK 0x00100000 /* NDFC Ready / Busy */
+#define SDR0_CUST0_NRB_BUSY 0x00100000 /* Busy */
+#define SDR0_CUST0_NRB_READY 0x00000000 /* Ready */
+
+#define SDR0_CUST0_NDRSC_MASK 0x0000FFF0 /* NDFC Device Reset Count Mask */
+#define SDR0_CUST0_NDRSC_ENCODE(n) ((((u32)(n)) & 0xFFF) << 4)
+#define SDR0_CUST0_NDRSC_DECODE(n) ((((u32)(n)) >> 4) & 0xFFF)
+
+#define SDR0_CUST0_CHIPSELGAT_MASK 0x0000000F /* Chip Select Gating Mask */
+#define SDR0_CUST0_CHIPSELGAT_DIS 0x00000000 /* Chip Select Gating Disable */
+#define SDR0_CUST0_CHIPSELGAT_ENALL 0x0000000F /*All Chip Select Gating Enable*/
+#define SDR0_CUST0_CHIPSELGAT_EN0 0x00000008 /* Chip Select0 Gating Enable */
+#define SDR0_CUST0_CHIPSELGAT_EN1 0x00000004 /* Chip Select1 Gating Enable */
+#define SDR0_CUST0_CHIPSELGAT_EN2 0x00000002 /* Chip Select2 Gating Enable */
+#define SDR0_CUST0_CHIPSELGAT_EN3 0x00000001 /* Chip Select3 Gating Enable */
+
+#define SDR0_SRST_DMC 0x00200000
+
+#define PLLSYS0_ENG_MASK 0x80000000 /* 0 = SysClk, 1 = PLL VCO */
+#define PLLSYS0_SRC_MASK 0x40000000 /* 0 = PLL A, 1 = PLL B */
+#define PLLSYS0_SEL_MASK 0x38000000 /* 0 = PLL, 1 = CPU, 5 = PerClk */
+#define PLLSYS0_TUNE_MASK 0x07fe0000 /* PLL Tune bits */
+#define PLLSYS0_FB_DIV_MASK 0x0001f000 /* Feedback divisor */
+#define PLLSYS0_FWD_DIV_A_MASK 0x00000f00 /* Fwd Div A */
+#define PLLSYS0_FWD_DIV_B_MASK 0x000000e0 /* Fwd Div B */
+#define PLLSYS0_PRI_DIV_B_MASK 0x0000001c /* PLL Primary Divisor B */
+#define PLLSYS0_OPB_DIV_MASK 0x00000003 /* OPB Divisor */
+
+#define PLLC_ENG_MASK 0x20000000 /* PLL primary forward divisor source */
+#define PLLC_SRC_MASK 0x20000000 /* PLL feedback source */
+#define PLLD_FBDV_MASK 0x1f000000 /* PLL Feedback Divisor */
+#define PLLD_FWDVA_MASK 0x000f0000 /* PLL Forward Divisor A */
+#define PLLD_FWDVB_MASK 0x00000700 /* PLL Forward Divisor B */
+#define PLLD_LFBDV_MASK 0x0000003f /* PLL Local Feedback Divisor */
+
+#define OPBDDV_MASK 0x03000000 /* OPB Clock Divisor Register */
+#define PERDV_MASK 0x07000000 /* Periferal Clock Divisor */
+#define PRADV_MASK 0x07000000 /* Primary Divisor A */
+#define PRBDV_MASK 0x07000000 /* Primary Divisor B */
+#define SPCID_MASK 0x03000000 /* Sync PCI Divisor */
+
+/* Strap 1 Register */
+#define PLLSYS1_LF_DIV_MASK 0xfc000000 /* PLL Local Feedback Divisor */
+#define PLLSYS1_PERCLK_DIV_MASK 0x03000000 /* Peripheral Clk Divisor */
+#define PLLSYS1_MAL_DIV_MASK 0x00c00000 /* MAL Clk Divisor */
+#define PLLSYS1_RW_MASK 0x00300000 /* ROM width */
+#define PLLSYS1_EAR_MASK 0x00080000 /* ERAP Addres reset vector */
+#define PLLSYS1_PAE_MASK 0x00040000 /* PCI arbitor enable */
+#define PLLSYS1_PCHE_MASK 0x00020000 /* PCI host config enable */
+#define PLLSYS1_PISE_MASK 0x00010000 /* PCI init seq. enable */
+#define PLLSYS1_PCWE_MASK 0x00008000 /* PCI local cpu wait enable */
+#define PLLSYS1_PPIM_MASK 0x00007800 /* PCI inbound map */
+#define PLLSYS1_PR64E_MASK 0x00000400 /* PCI init Req64 enable */
+#define PLLSYS1_PXFS_MASK 0x00000300 /* PCI-X Freq Sel */
+#define PLLSYS1_RSVD_MASK 0x00000080 /* RSVD */
+#define PLLSYS1_PDM_MASK 0x00000040 /* PCI-X Driver Mode */
+#define PLLSYS1_EPS_MASK 0x00000038 /* Ethernet Pin Select */
+#define PLLSYS1_RMII_MASK 0x00000004 /* RMII Mode */
+#define PLLSYS1_TRE_MASK 0x00000002 /* GPIO Trace Enable */
+#define PLLSYS1_NTO1_MASK 0x00000001 /* CPU:PLB N-to-1 ratio */
+
+#define CPR0_ICFG_RLI_MASK 0x80000000
+#define CPR0_ICFG_ICS_MASK 0x00000007
+#define CPR0_SPCID_SPCIDV0_MASK 0x03000000
+#define CPR0_SPCID_SPCIDV0_DIV1 0x01000000
+#define CPR0_SPCID_SPCIDV0_DIV2 0x02000000
+#define CPR0_SPCID_SPCIDV0_DIV3 0x03000000
+#define CPR0_SPCID_SPCIDV0_DIV4 0x00000000
+#define CPR0_PERD_PERDV0_MASK 0x07000000
+
+#define PCI_MMIO_LCR_BASE (CONFIG_SYS_PCI_BASE + 0x0f400000) /* Real =>
+ 0x0EF400000 */
+
+/* PCI Master Local Configuration Registers */
+#define PCIL0_PMM0LA (PCI_MMIO_LCR_BASE + 0x00) /* PMM0 Local Address */
+#define PCIL0_PMM0MA (PCI_MMIO_LCR_BASE + 0x04) /* PMM0 Mask/Attribute */
+#define PCIL0_PMM0PCILA (PCI_MMIO_LCR_BASE + 0x08) /* PMM0 PCI Low Address */
+#define PCIL0_PMM0PCIHA (PCI_MMIO_LCR_BASE + 0x0C) /* PMM0 PCI High Address */
+#define PCIL0_PMM1LA (PCI_MMIO_LCR_BASE + 0x10) /* PMM1 Local Address */
+#define PCIL0_PMM1MA (PCI_MMIO_LCR_BASE + 0x14) /* PMM1 Mask/Attribute */
+#define PCIL0_PMM1PCILA (PCI_MMIO_LCR_BASE + 0x18) /* PMM1 PCI Low Address */
+#define PCIL0_PMM1PCIHA (PCI_MMIO_LCR_BASE + 0x1C) /* PMM1 PCI High Address */
+#define PCIL0_PMM2LA (PCI_MMIO_LCR_BASE + 0x20) /* PMM2 Local Address */
+#define PCIL0_PMM2MA (PCI_MMIO_LCR_BASE + 0x24) /* PMM2 Mask/Attribute */
+#define PCIL0_PMM2PCILA (PCI_MMIO_LCR_BASE + 0x28) /* PMM2 PCI Low Address */
+#define PCIL0_PMM2PCIHA (PCI_MMIO_LCR_BASE + 0x2C) /* PMM2 PCI High Address */
+
+/* PCI Target Local Configuration Registers */
+#define PCIL0_PTM1MS (PCI_MMIO_LCR_BASE + 0x30) /* PTM1 Memory Size/
+ Attribute */
+#define PCIL0_PTM1LA (PCI_MMIO_LCR_BASE + 0x34) /* PTM1 Local Addr. Reg */
+#define PCIL0_PTM2MS (PCI_MMIO_LCR_BASE + 0x38) /* PTM2 Memory Size/
+ Attribute */
+#define PCIL0_PTM2LA (PCI_MMIO_LCR_BASE + 0x3C) /* PTM2 Local Addr. Reg */
+
+#endif /* _PPC440EP_GR_H_ */
diff --git a/arch/powerpc/include/asm/ppc440epx_grx.h b/arch/powerpc/include/asm/ppc440epx_grx.h
new file mode 100644
index 0000000..dfaa609
--- /dev/null
+++ b/arch/powerpc/include/asm/ppc440epx_grx.h
@@ -0,0 +1,460 @@
+/*
+ * (C) Copyright 2010
+ * Stefan Roese, DENX Software Engineering, sr@denx.de.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef _PPC440EPX_GRX_H_
+#define _PPC440EPX_GRX_H_
+
+#define CONFIG_SDRAM_PPC4xx_DENALI_DDR2 /* Denali DDR(2) controller */
+
+#define CONFIG_NAND_NDFC
+
+#define CONFIG_SYS_PPC4xx_PLB4_ARBITER
+
+/*
+ * Some SoC specific registers (not common for all 440 SoC's)
+ */
+
+/* Memory mapped registers */
+#define SPI0_MODE 0xef600090
+#define GPIO0_BASE (CONFIG_SYS_PERIPHERAL_BASE + 0x00000B00)
+#define GPIO1_BASE (CONFIG_SYS_PERIPHERAL_BASE + 0x00000C00)
+
+/* DCR */
+#define CPM0_ER 0x00b0
+#define CPM1_ER 0x00f0
+#define PLB3A0_ACR 0x0077
+#define PLB4A0_ACR 0x0081
+#define PLB4A1_ACR 0x0089
+#define OPB2PLB40_BCTRL 0x0350
+#define P4P3BO0_CFG 0x0026
+
+/* SDR */
+#define SDR0_DDRCFG 0x00e0
+#define SDR0_PCI0 0x0300
+#define SDR0_SDSTP2 0x4001
+#define SDR0_SDSTP3 0x4003
+#define SDR0_EMAC0RXST 0x4301
+#define SDR0_EMAC0TXST 0x4302
+#define SDR0_CRYP0 0x4500
+
+#define SDR0_SDSTP1_PAE_MASK (0x80000000 >> 21)
+#define SDR0_SDSTP1_PAME_MASK (0x80000000 >> 27)
+
+/* Pin Function Control Register 1 */
+#define SDR0_PFC1_U1ME_MASK 0x02000000 /* UART1 Mode Enable */
+#define SDR0_PFC1_U1ME_DSR_DTR 0x00000000 /* UART1 in DSR/DTR Mode */
+#define SDR0_PFC1_U1ME_CTS_RTS 0x02000000 /* UART1 in CTS/RTS Mode */
+#define SDR0_PFC1_SELECT_MASK 0x01C00000 /* Ethernet Pin Select
+ EMAC 0 */
+#define SDR0_PFC1_SELECT_CONFIG_1_1 0x00C00000 /* 1xMII using RGMII
+ bridge */
+#define SDR0_PFC1_SELECT_CONFIG_1_2 0x00000000 /* 1xMII using ZMII
+ bridge */
+#define SDR0_PFC1_SELECT_CONFIG_2 0x00C00000 /* 1xGMII using RGMII
+ bridge */
+#define SDR0_PFC1_SELECT_CONFIG_3 0x01000000 /* 1xTBI using RGMII
+ bridge */
+#define SDR0_PFC1_SELECT_CONFIG_4 0x01400000 /* 2xRGMII using RGMII
+ bridge */
+#define SDR0_PFC1_SELECT_CONFIG_5 0x01800000 /* 2xRTBI using RGMII
+ bridge */
+#define SDR0_PFC1_SELECT_CONFIG_6 0x00800000 /* 2xSMII using ZMII
+ bridge */
+#define SDR0_PFC1_U0ME_MASK 0x00080000 /* UART0 Mode Enable */
+#define SDR0_PFC1_U0ME_DSR_DTR 0x00000000 /* UART0 in DSR/DTR Mode */
+#define SDR0_PFC1_U0ME_CTS_RTS 0x00080000 /* UART0 in CTS/RTS Mode */
+#define SDR0_PFC1_U0IM_MASK 0x00040000 /* UART0 Interface Mode */
+#define SDR0_PFC1_U0IM_8PINS 0x00000000 /* UART0 Interface Mode 8 pins */
+#define SDR0_PFC1_U0IM_4PINS 0x00040000 /* UART0 Interface Mode 4 pins */
+#define SDR0_PFC1_SIS_MASK 0x00020000 /* SCP or IIC1 Selection */
+#define SDR0_PFC1_SIS_SCP_SEL 0x00000000 /* SCP Selected */
+#define SDR0_PFC1_SIS_IIC1_SEL 0x00020000 /* IIC1 Selected */
+#define SDR0_PFC1_UES_MASK 0x00010000 /* USB2D_RX_Active / EBC_Hold
+ Req Selection */
+#define SDR0_PFC1_UES_USB2D_SEL 0x00000000 /* USB2D_RX_Active Selected */
+#define SDR0_PFC1_UES_EBCHR_SEL 0x00010000 /* EBC_Hold Req Selected */
+#define SDR0_PFC1_DIS_MASK 0x00008000 /* DMA_Req(1) / UIC_IRQ(5)
+ Selection */
+#define SDR0_PFC1_DIS_DMAR_SEL 0x00000000 /* DMA_Req(1) Selected */
+#define SDR0_PFC1_DIS_UICIRQ5_SEL 0x00008000 /* UIC_IRQ(5) Selected */
+#define SDR0_PFC1_ERE_MASK 0x00004000 /* EBC Mast.Ext.Req.En./GPIO0(27)
+ Selection */
+#define SDR0_PFC1_ERE_EXTR_SEL 0x00000000 /* EBC Mast.Ext.Req.En.
+ Selected */
+#define SDR0_PFC1_ERE_GPIO0_27_SEL 0x00004000 /* GPIO0(27) Selected */
+#define SDR0_PFC1_UPR_MASK 0x00002000 /* USB2 Device Packet Reject
+ Selection */
+#define SDR0_PFC1_UPR_DISABLE 0x00000000 /* USB2 Device Packet Reject
+ Disable */
+#define SDR0_PFC1_UPR_ENABLE 0x00002000 /* USB2 Device Packet Reject
+ Enable */
+#define SDR0_PFC1_PLB_PME_MASK 0x00001000 /* PLB3/PLB4 Perf. Monitor Enable
+ Selection */
+#define SDR0_PFC1_PLB_PME_PLB3_SEL 0x00000000 /* PLB3 Performance Monitor
+ Enable */
+#define SDR0_PFC1_PLB_PME_PLB4_SEL 0x00001000 /* PLB3 Performance Monitor
+ Enable */
+#define SDR0_PFC1_GFGGI_MASK 0x0000000F /* GPT Frequency Generation
+ Gated In */
+
+#define SDR0_PFC2_SELECT_MASK 0xe0000000 /* Ethernet Pin select EMAC1 */
+#define SDR0_PFC2_SELECT_CONFIG_1_1 0x60000000 /* 1xMII using RGMII bridge */
+#define SDR0_PFC2_SELECT_CONFIG_1_2 0x00000000 /* 1xMII using ZMII bridge */
+#define SDR0_PFC2_SELECT_CONFIG_2 0x60000000 /* 1xGMII using RGMII bridge */
+#define SDR0_PFC2_SELECT_CONFIG_3 0x80000000 /* 1xTBI using RGMII bridge */
+#define SDR0_PFC2_SELECT_CONFIG_4 0xa0000000 /* 2xRGMII using RGMII bridge */
+#define SDR0_PFC2_SELECT_CONFIG_5 0xc0000000 /* 2xRTBI using RGMII bridge */
+#define SDR0_PFC2_SELECT_CONFIG_6 0x40000000 /* 2xSMII using ZMII bridge */
+
+#define SDR0_USB2D0CR 0x0320
+#define SDR0_USB2D0CR_USB2DEV_EBC_SEL_MASK 0x00000004 /* USB 2.0 Device/EBC
+ Master Selection */
+#define SDR0_USB2D0CR_USB2DEV_SELECTION 0x00000004 /* USB 2.0 Device Selection*/
+#define SDR0_USB2D0CR_EBC_SELECTION 0x00000000 /* EBC Selection */
+
+#define SDR0_USB2D0CR_USB_DEV_INT_SEL_MASK 0x00000002 /* USB Device Interface
+ Selection */
+#define SDR0_USB2D0CR_USB20D_DEVSEL 0x00000000 /* USB2.0 Device Selected */
+#define SDR0_USB2D0CR_USB11D_DEVSEL 0x00000002 /* USB1.1 Device Selected */
+
+#define SDR0_USB2D0CR_LEEN_MASK 0x00000001 /* Little Endian selection */
+#define SDR0_USB2D0CR_LEEN_DISABLE 0x00000000 /* Little Endian Disable */
+#define SDR0_USB2D0CR_LEEN_ENABLE 0x00000001 /* Little Endian Enable */
+
+/* USB2 Host Control Register */
+#define SDR0_USB2H0CR 0x0340
+#define SDR0_USB2H0CR_WDINT_MASK 0x00000001 /* Host UTMI Word Interface*/
+#define SDR0_USB2H0CR_WDINT_8BIT_60MHZ 0x00000000 /* 8-bit/60MHz */
+#define SDR0_USB2H0CR_WDINT_16BIT_30MHZ 0x00000001 /* 16-bit/30MHz */
+#define SDR0_USB2H0CR_EFLADJ_MASK 0x0000007e /* EHCI Frame Length
+ Adjustment */
+/* USB2PHY0 Control Register */
+#define SDR0_USB2PHY0CR 0x4103
+#define SDR0_USB2PHY0CR_UTMICN_MASK 0x00100000
+
+ /* PHY UTMI interface connection */
+#define SDR0_USB2PHY0CR_UTMICN_DEV 0x00000000 /* Device support */
+#define SDR0_USB2PHY0CR_UTMICN_HOST 0x00100000 /* Host support */
+
+#define SDR0_USB2PHY0CR_DWNSTR_MASK 0x00400000 /* Select downstream port mode */
+#define SDR0_USB2PHY0CR_DWNSTR_DEV 0x00000000 /* Device */
+#define SDR0_USB2PHY0CR_DWNSTR_HOST 0x00400000 /* Host */
+
+/* VBus detect (Device mode only) */
+#define SDR0_USB2PHY0CR_DVBUS_MASK 0x00800000
+/* Pull-up resistance on D+ is disabled */
+#define SDR0_USB2PHY0CR_DVBUS_PURDIS 0x00000000
+/* Pull-up resistance on D+ is enabled */
+#define SDR0_USB2PHY0CR_DVBUS_PUREN 0x00800000
+
+/* PHY UTMI data width and clock select */
+#define SDR0_USB2PHY0CR_WDINT_MASK 0x01000000
+#define SDR0_USB2PHY0CR_WDINT_8BIT_60MHZ 0x00000000 /* 8-bit data/60MHz */
+#define SDR0_USB2PHY0CR_WDINT_16BIT_30MHZ 0x01000000 /* 16-bit data/30MHz */
+
+#define SDR0_USB2PHY0CR_LOOPEN_MASK 0x02000000 /* Loop back test enable */
+#define SDR0_USB2PHY0CR_LOOP_ENABLE 0x00000000 /* Loop back disabled */
+/* Loop back enabled (only test purposes) */
+#define SDR0_USB2PHY0CR_LOOP_DISABLE 0x02000000
+
+/* Force XO block on during a suspend */
+#define SDR0_USB2PHY0CR_XOON_MASK 0x04000000
+#define SDR0_USB2PHY0CR_XO_ON 0x00000000 /* PHY XO block is powered-on */
+/* PHY XO block is powered-off when all ports are suspended */
+#define SDR0_USB2PHY0CR_XO_OFF 0x04000000
+
+#define SDR0_USB2PHY0CR_PWRSAV_MASK 0x08000000 /* Select PHY power-save mode */
+#define SDR0_USB2PHY0CR_PWRSAV_OFF 0x00000000 /* Non-power-save mode */
+#define SDR0_USB2PHY0CR_PWRSAV_ON 0x08000000 /* Power-save mode. Valid only
+ for full-speed operation */
+
+#define SDR0_USB2PHY0CR_XOREF_MASK 0x10000000 /* Select reference clock
+ source */
+#define SDR0_USB2PHY0CR_XOREF_INTERNAL 0x00000000 /* PHY PLL uses chip internal
+ 48M clock as a reference */
+#define SDR0_USB2PHY0CR_XOREF_XO 0x10000000 /* PHY PLL uses internal XO
+ block output as a reference */
+
+#define SDR0_USB2PHY0CR_XOCLK_MASK 0x20000000 /* Select clock for XO
+ block*/
+#define SDR0_USB2PHY0CR_XOCLK_EXTERNAL 0x00000000 /* PHY macro used an external
+ clock */
+#define SDR0_USB2PHY0CR_XOCLK_CRYSTAL 0x20000000 /* PHY macro uses the clock
+ from a crystal */
+
+#define SDR0_USB2PHY0CR_CLKSEL_MASK 0xc0000000 /* Select ref clk freq */
+#define SDR0_USB2PHY0CR_CLKSEL_12MHZ 0x00000000 /* Select ref clk freq
+ = 12 MHz */
+#define SDR0_USB2PHY0CR_CLKSEL_48MHZ 0x40000000 /* Select ref clk freq
+ = 48 MHz */
+#define SDR0_USB2PHY0CR_CLKSEL_24MHZ 0x80000000 /* Select ref clk freq
+ = 24 MHz */
+
+/* USB2.0 Device */
+/*
+ * todo: check if this can be completely removed, only used in
+ * cpu/ppc4xx/usbdev.c. And offsets are completely wrong. This could
+ * never have actually worked. Best probably is to remove this
+ * usbdev.c file completely (and these defines).
+ */
+#define USB2D0_BASE CONFIG_SYS_USB2D0_BASE
+
+#define USB2D0_INTRIN (USB2D0_BASE + 0x00000000)
+
+#define USB2D0_INTRIN (USB2D0_BASE + 0x00000000) /* Interrupt register for
+ Endpoint 0 plus IN Endpoints 1 to 3 */
+#define USB2D0_POWER (USB2D0_BASE + 0x00000000) /* Power management
+ register */
+#define USB2D0_FADDR (USB2D0_BASE + 0x00000000) /* Function address
+ register */
+#define USB2D0_INTRINE (USB2D0_BASE + 0x00000000) /* Interrupt enable
+ register for USB2D0_INTRIN */
+#define USB2D0_INTROUT (USB2D0_BASE + 0x00000000) /* Interrupt register for
+ OUT Endpoints 1 to 3 */
+#define USB2D0_INTRUSBE (USB2D0_BASE + 0x00000000) /* Interrupt enable
+ register for USB2D0_INTRUSB */
+#define USB2D0_INTRUSB (USB2D0_BASE + 0x00000000) /* Interrupt register for
+ common USB interrupts */
+#define USB2D0_INTROUTE (USB2D0_BASE + 0x00000000) /* Interrupt enable
+ register for IntrOut */
+#define USB2D0_TSTMODE (USB2D0_BASE + 0x00000000) /* Enables the USB 2.0
+ test modes */
+#define USB2D0_INDEX (USB2D0_BASE + 0x00000000) /* Index register for
+ selecting the Endpoint status/control registers */
+#define USB2D0_FRAME (USB2D0_BASE + 0x00000000) /* Frame number */
+#define USB2D0_INCSR0 (USB2D0_BASE + 0x00000000) /* Control Status
+ register for Endpoint 0. (Index register set to select Endpoint 0) */
+#define USB2D0_INCSR (USB2D0_BASE + 0x00000000) /* Control Status
+ register for IN Endpoint. (Index register set to select Endpoints 13) */
+#define USB2D0_INMAXP (USB2D0_BASE + 0x00000000) /* Maximum packet
+ size for IN Endpoint. (Index register set to select Endpoints 13) */
+#define USB2D0_OUTCSR (USB2D0_BASE + 0x00000000) /* Control Status
+ register for OUT Endpoint. (Index register set to select Endpoints 13) */
+#define USB2D0_OUTMAXP (USB2D0_BASE + 0x00000000) /* Maximum packet
+ size for OUT Endpoint. (Index register set to select Endpoints 13) */
+#define USB2D0_OUTCOUNT0 (USB2D0_BASE + 0x00000000) /* Number of received
+ bytes in Endpoint 0 FIFO. (Index register set to select Endpoint 0) */
+#define USB2D0_OUTCOUNT (USB2D0_BASE + 0x00000000) /* Number of bytes in
+ OUT Endpoint FIFO. (Index register set to select Endpoints 13) */
+
+/* Miscealleneaous Function Reg. */
+#define SDR0_MFR_ETH0_CLK_SEL_MASK 0x08000000 /* Ethernet0 Clock Select */
+#define SDR0_MFR_ETH0_CLK_SEL_EXT 0x00000000
+#define SDR0_MFR_ETH1_CLK_SEL_MASK 0x04000000 /* Ethernet1 Clock Select */
+#define SDR0_MFR_ETH1_CLK_SEL_EXT 0x00000000
+#define SDR0_MFR_ZMII_MODE_MASK 0x03000000 /* ZMII Mode Mask */
+#define SDR0_MFR_ZMII_MODE_MII 0x00000000 /* ZMII Mode MII */
+#define SDR0_MFR_ZMII_MODE_SMII 0x01000000 /* ZMII Mode SMII */
+#define SDR0_MFR_ZMII_MODE_BIT0 0x02000000 /* ZMII Mode Bit0 */
+#define SDR0_MFR_ZMII_MODE_BIT1 0x01000000 /* ZMII Mode Bit1 */
+#define SDR0_MFR_ZM_ENCODE(n) ((((u32)(n)) & 0x3) << 24)
+#define SDR0_MFR_ZM_DECODE(n) ((((u32)(n)) << 24) & 0x3)
+#define SDR0_MFR_PKT_REJ_MASK 0x00300000 /* Pkt Rej. Enable Mask */
+#define SDR0_MFR_PKT_REJ_EN 0x00300000 /* Pkt Rej. Ena. on both EMAC3 0-1 */
+#define SDR0_MFR_PKT_REJ_EN0 0x00200000 /* Pkt Rej. Enable on EMAC3(0) */
+#define SDR0_MFR_PKT_REJ_EN1 0x00100000 /* Pkt Rej. Enable on EMAC3(1) */
+#define SDR0_MFR_PKT_REJ_POL 0x00080000 /* Packet Reject Polarity */
+
+/* CUST0 Customer Configuration Register0 */
+#define SDR0_CUST0_MUX_E_N_G_MASK 0xC0000000 /* Mux_Emac_NDFC_GPIO */
+#define SDR0_CUST0_MUX_EMAC_SEL 0x40000000 /* Emac Selection */
+#define SDR0_CUST0_MUX_NDFC_SEL 0x80000000 /* NDFC Selection */
+#define SDR0_CUST0_MUX_GPIO_SEL 0xC0000000 /* GPIO Selection */
+
+#define SDR0_CUST0_NDFC_EN_MASK 0x20000000 /* NDFC Enable Mask */
+#define SDR0_CUST0_NDFC_ENABLE 0x20000000 /* NDFC Enable */
+#define SDR0_CUST0_NDFC_DISABLE 0x00000000 /* NDFC Disable */
+
+#define SDR0_CUST0_NDFC_BW_MASK 0x10000000 /* NDFC Boot Width */
+#define SDR0_CUST0_NDFC_BW_16_BIT 0x10000000 /* NDFC Boot Width = 16 Bit */
+#define SDR0_CUST0_NDFC_BW_8_BIT 0x00000000 /* NDFC Boot Width = 8 Bit */
+
+#define SDR0_CUST0_NDFC_BP_MASK 0x0F000000 /* NDFC Boot Page */
+#define SDR0_CUST0_NDFC_BP_ENCODE(n) ((((u32)(n)) & 0xF) << 24)
+#define SDR0_CUST0_NDFC_BP_DECODE(n) ((((u32)(n)) >> 24) & 0xF)
+
+#define SDR0_CUST0_NDFC_BAC_MASK 0x00C00000 /* NDFC Boot Address Cycle */
+#define SDR0_CUST0_NDFC_BAC_ENCODE(n) ((((u32)(n)) & 0x3) << 22)
+#define SDR0_CUST0_NDFC_BAC_DECODE(n) ((((u32)(n)) >> 22) & 0x3)
+
+#define SDR0_CUST0_NDFC_ARE_MASK 0x00200000 /* NDFC Auto Read Enable */
+#define SDR0_CUST0_NDFC_ARE_ENABLE 0x00200000 /* NDFC Auto Read Enable */
+#define SDR0_CUST0_NDFC_ARE_DISABLE 0x00000000 /* NDFC Auto Read Disable */
+
+#define SDR0_CUST0_NRB_MASK 0x00100000 /* NDFC Ready / Busy */
+#define SDR0_CUST0_NRB_BUSY 0x00100000 /* Busy */
+#define SDR0_CUST0_NRB_READY 0x00000000 /* Ready */
+
+#define SDR0_CUST0_NDRSC_MASK 0x0000FFF0 /* NDFC Device Reset Count Mask */
+#define SDR0_CUST0_NDRSC_ENCODE(n) ((((u32)(n)) & 0xFFF) << 4)
+#define SDR0_CUST0_NDRSC_DECODE(n) ((((u32)(n)) >> 4) & 0xFFF)
+
+#define SDR0_CUST0_CHIPSELGAT_MASK 0x0000000F /* Chip Select Gating Mask */
+#define SDR0_CUST0_CHIPSELGAT_DIS 0x00000000 /* Chip Select Gating Disable */
+#define SDR0_CUST0_CHIPSELGAT_ENALL 0x0000000F /*All Chip Select Gating Enable*/
+#define SDR0_CUST0_CHIPSELGAT_EN0 0x00000008 /* Chip Select0 Gating Enable */
+#define SDR0_CUST0_CHIPSELGAT_EN1 0x00000004 /* Chip Select1 Gating Enable */
+#define SDR0_CUST0_CHIPSELGAT_EN2 0x00000002 /* Chip Select2 Gating Enable */
+#define SDR0_CUST0_CHIPSELGAT_EN3 0x00000001 /* Chip Select3 Gating Enable */
+
+#define SDR0_SRST0_BGO 0x80000000 /* PLB to OPB bridge */
+#define SDR0_SRST0_PLB4 0x40000000 /* PLB4 arbiter */
+#define SDR0_SRST0_EBC 0x20000000 /* External bus controller */
+#define SDR0_SRST0_OPB 0x10000000 /* OPB arbiter */
+#define SDR0_SRST0_UART0 0x08000000 /* Universal asynchronous receiver/
+ transmitter 0 */
+#define SDR0_SRST0_UART1 0x04000000 /* Universal asynchronous receiver/
+ transmitter 1 */
+#define SDR0_SRST0_IIC0 0x02000000 /* Inter integrated circuit 0 */
+#define SDR0_SRST0_USB2H 0x01000000 /* USB2.0 Host */
+#define SDR0_SRST0_GPIO 0x00800000 /* General purpose I/O */
+#define SDR0_SRST0_GPT 0x00400000 /* General purpose timer */
+#define SDR0_SRST0_DMC 0x00200000 /* DDR SDRAM memory controller */
+#define SDR0_SRST0_PCI 0x00100000 /* PCI */
+#define SDR0_SRST0_EMAC0 0x00080000 /* Ethernet media access controller 0 */
+#define SDR0_SRST0_EMAC1 0x00040000 /* Ethernet media access controller 1 */
+#define SDR0_SRST0_CPM0 0x00020000 /* Clock and power management */
+#define SDR0_SRST0_ZMII 0x00010000 /* ZMII bridge */
+#define SDR0_SRST0_UIC0 0x00008000 /* Universal interrupt controller 0 */
+#define SDR0_SRST0_UIC1 0x00004000 /* Universal interrupt controller 1 */
+#define SDR0_SRST0_IIC1 0x00002000 /* Inter integrated circuit 1 */
+#define SDR0_SRST0_SCP 0x00001000 /* Serial communications port */
+#define SDR0_SRST0_BGI 0x00000800 /* OPB to PLB bridge */
+#define SDR0_SRST0_DMA 0x00000400 /* Direct memory access controller */
+#define SDR0_SRST0_DMAC 0x00000200 /* DMA channel */
+#define SDR0_SRST0_MAL 0x00000100 /* Media access layer */
+#define SDR0_SRST0_USB2D 0x00000080 /* USB2.0 device */
+#define SDR0_SRST0_GPTR 0x00000040 /* General purpose timer */
+#define SDR0_SRST0_P4P3 0x00000010 /* PLB4 to PLB3 bridge */
+#define SDR0_SRST0_P3P4 0x00000008 /* PLB3 to PLB4 bridge */
+#define SDR0_SRST0_PLB3 0x00000004 /* PLB3 arbiter */
+#define SDR0_SRST0_UART2 0x00000002 /* Universal asynchronous receiver/
+ transmitter 2 */
+#define SDR0_SRST0_UART3 0x00000001 /* Universal asynchronous receiver/
+ transmitter 3 */
+
+#define SDR0_SRST1_NDFC 0x80000000 /* Nand flash controller */
+#define SDR0_SRST1_OPBA1 0x40000000 /* OPB Arbiter attached to PLB4 */
+#define SDR0_SRST1_P4OPB0 0x20000000 /* PLB4 to OPB Bridge0 */
+#define SDR0_SRST1_PLB42OPB0 SDR0_SRST1_P4OPB0
+#define SDR0_SRST1_DMA4 0x10000000 /* DMA to PLB4 */
+#define SDR0_SRST1_DMA4CH 0x08000000 /* DMA Channel to PLB4 */
+#define SDR0_SRST1_OPBA2 0x04000000 /* OPB Arbiter attached to PLB4
+ USB 2.0 Host */
+#define SDR0_SRST1_OPB2PLB40 0x02000000 /* OPB to PLB4 Bridge attached to
+ USB 2.0 Host */
+#define SDR0_SRST1_PLB42OPB1 0x01000000 /* PLB4 to OPB Bridge attached to
+ USB 2.0 Host */
+#define SDR0_SRST1_CPM1 0x00800000 /* Clock and Power management 1 */
+#define SDR0_SRST1_UIC2 0x00400000 /* Universal Interrupt Controller 2*/
+#define SDR0_SRST1_CRYP0 0x00200000 /* Security Engine */
+#define SDR0_SRST1_USB20PHY 0x00100000 /* USB 2.0 Phy */
+#define SDR0_SRST1_USB2HUTMI 0x00080000 /* USB 2.0 Host UTMI Interface */
+#define SDR0_SRST1_USB2HPHY 0x00040000 /* USB 2.0 Host Phy Interface */
+#define SDR0_SRST1_SRAM0 0x00020000 /* Internal SRAM Controller */
+#define SDR0_SRST1_RGMII0 0x00010000 /* RGMII Bridge */
+#define SDR0_SRST1_ETHPLL 0x00008000 /* Ethernet PLL */
+#define SDR0_SRST1_FPU 0x00004000 /* Floating Point Unit */
+#define SDR0_SRST1_KASU0 0x00002000 /* Kasumi Engine */
+
+#define PLLSYS0_ENG_MASK 0x80000000 /* 0 = SysClk, 1 = PLL VCO */
+#define PLLSYS0_SRC_MASK 0x40000000 /* 0 = PLL A, 1 = PLL B */
+#define PLLSYS0_SEL_MASK 0x38000000 /* 0 = PLL, 1 = CPU, 5 = PerClk */
+#define PLLSYS0_TUNE_MASK 0x07fe0000 /* PLL Tune bits */
+#define PLLSYS0_FB_DIV_MASK 0x0001f000 /* Feedback divisor */
+#define PLLSYS0_FWD_DIV_A_MASK 0x00000f00 /* Fwd Div A */
+#define PLLSYS0_FWD_DIV_B_MASK 0x000000e0 /* Fwd Div B */
+#define PLLSYS0_PRI_DIV_B_MASK 0x0000001c /* PLL Primary Divisor B */
+#define PLLSYS0_OPB_DIV_MASK 0x00000003 /* OPB Divisor */
+
+#define PLLC_ENG_MASK 0x20000000 /* PLL primary forward divisor source */
+#define PLLC_SRC_MASK 0x20000000 /* PLL feedback source */
+#define PLLD_FBDV_MASK 0x1f000000 /* PLL Feedback Divisor */
+#define PLLD_FWDVA_MASK 0x000f0000 /* PLL Forward Divisor A */
+#define PLLD_FWDVB_MASK 0x00000700 /* PLL Forward Divisor B */
+#define PLLD_LFBDV_MASK 0x0000003f /* PLL Local Feedback Divisor */
+
+#define OPBDDV_MASK 0x03000000 /* OPB Clock Divisor Register */
+#define PERDV_MASK 0x07000000 /* Periferal Clock Divisor */
+#define PRADV_MASK 0x07000000 /* Primary Divisor A */
+#define PRBDV_MASK 0x07000000 /* Primary Divisor B */
+#define SPCID_MASK 0x03000000 /* Sync PCI Divisor */
+
+/* Strap 1 Register */
+#define PLLSYS1_LF_DIV_MASK 0xfc000000 /* PLL Local Feedback Divisor */
+#define PLLSYS1_PERCLK_DIV_MASK 0x03000000 /* Peripheral Clk Divisor */
+#define PLLSYS1_MAL_DIV_MASK 0x00c00000 /* MAL Clk Divisor */
+#define PLLSYS1_RW_MASK 0x00300000 /* ROM width */
+#define PLLSYS1_EAR_MASK 0x00080000 /* ERAP Addres reset vector */
+#define PLLSYS1_PAE_MASK 0x00040000 /* PCI arbitor enable */
+#define PLLSYS1_PCHE_MASK 0x00020000 /* PCI host config enable */
+#define PLLSYS1_PISE_MASK 0x00010000 /* PCI init seq. enable */
+#define PLLSYS1_PCWE_MASK 0x00008000 /* PCI local cpu wait enable */
+#define PLLSYS1_PPIM_MASK 0x00007800 /* PCI inbound map */
+#define PLLSYS1_PR64E_MASK 0x00000400 /* PCI init Req64 enable */
+#define PLLSYS1_PXFS_MASK 0x00000300 /* PCI-X Freq Sel */
+#define PLLSYS1_RSVD_MASK 0x00000080 /* RSVD */
+#define PLLSYS1_PDM_MASK 0x00000040 /* PCI-X Driver Mode */
+#define PLLSYS1_EPS_MASK 0x00000038 /* Ethernet Pin Select */
+#define PLLSYS1_RMII_MASK 0x00000004 /* RMII Mode */
+#define PLLSYS1_TRE_MASK 0x00000002 /* GPIO Trace Enable */
+#define PLLSYS1_NTO1_MASK 0x00000001 /* CPU:PLB N-to-1 ratio */
+
+#define CPR0_ICFG_RLI_MASK 0x80000000
+#define CPR0_ICFG_ICS_MASK 0x00000007
+#define CPR0_SPCID_SPCIDV0_MASK 0x03000000
+#define CPR0_SPCID_SPCIDV0_DIV1 0x01000000
+#define CPR0_SPCID_SPCIDV0_DIV2 0x02000000
+#define CPR0_SPCID_SPCIDV0_DIV3 0x03000000
+#define CPR0_SPCID_SPCIDV0_DIV4 0x00000000
+#define CPR0_PERD_PERDV0_MASK 0x07000000
+
+#define PCI_MMIO_LCR_BASE (CONFIG_SYS_PCI_BASE + 0x0f400000) /* Real =>
+ 0x0EF400000 */
+
+/* PCI Master Local Configuration Registers */
+#define PCIL0_PMM0LA (PCI_MMIO_LCR_BASE + 0x00) /* PMM0 Local Address */
+#define PCIL0_PMM0MA (PCI_MMIO_LCR_BASE + 0x04) /* PMM0 Mask/Attribute */
+#define PCIL0_PMM0PCILA (PCI_MMIO_LCR_BASE + 0x08) /* PMM0 PCI Low Address */
+#define PCIL0_PMM0PCIHA (PCI_MMIO_LCR_BASE + 0x0C) /* PMM0 PCI High Address */
+#define PCIL0_PMM1LA (PCI_MMIO_LCR_BASE + 0x10) /* PMM1 Local Address */
+#define PCIL0_PMM1MA (PCI_MMIO_LCR_BASE + 0x14) /* PMM1 Mask/Attribute */
+#define PCIL0_PMM1PCILA (PCI_MMIO_LCR_BASE + 0x18) /* PMM1 PCI Low Address */
+#define PCIL0_PMM1PCIHA (PCI_MMIO_LCR_BASE + 0x1C) /* PMM1 PCI High Address */
+#define PCIL0_PMM2LA (PCI_MMIO_LCR_BASE + 0x20) /* PMM2 Local Address */
+#define PCIL0_PMM2MA (PCI_MMIO_LCR_BASE + 0x24) /* PMM2 Mask/Attribute */
+#define PCIL0_PMM2PCILA (PCI_MMIO_LCR_BASE + 0x28) /* PMM2 PCI Low Address */
+#define PCIL0_PMM2PCIHA (PCI_MMIO_LCR_BASE + 0x2C) /* PMM2 PCI High Address */
+
+/* PCI Target Local Configuration Registers */
+#define PCIL0_PTM1MS (PCI_MMIO_LCR_BASE + 0x30) /* PTM1 Memory Size/
+ Attribute */
+#define PCIL0_PTM1LA (PCI_MMIO_LCR_BASE + 0x34) /* PTM1 Local Addr. Reg */
+#define PCIL0_PTM2MS (PCI_MMIO_LCR_BASE + 0x38) /* PTM2 Memory Size/
+ Attribute */
+#define PCIL0_PTM2LA (PCI_MMIO_LCR_BASE + 0x3C) /* PTM2 Local Addr. Reg */
+
+/* 440EPx boot strap options */
+#define BOOT_STRAP_OPTION_A 0x00000000
+#define BOOT_STRAP_OPTION_B 0x00000001
+#define BOOT_STRAP_OPTION_D 0x00000003
+#define BOOT_STRAP_OPTION_E 0x00000004
+
+#endif /* _PPC440EPX_GRX_H_ */
diff --git a/arch/powerpc/include/asm/ppc440gp.h b/arch/powerpc/include/asm/ppc440gp.h
new file mode 100644
index 0000000..0c95e91
--- /dev/null
+++ b/arch/powerpc/include/asm/ppc440gp.h
@@ -0,0 +1,65 @@
+/*
+ * (C) Copyright 2010
+ * Stefan Roese, DENX Software Engineering, sr@denx.de.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef _PPC440GP_H_
+#define _PPC440GP_H_
+
+#define CONFIG_SDRAM_PPC4xx_IBM_DDR /* IBM DDR controller */
+
+/*
+ * Some SoC specific registers (not common for all 440 SoC's)
+ */
+#define GPIO0_BASE (CONFIG_SYS_PERIPHERAL_BASE + 0x00000700)
+
+#define SDR0_PCI0 0x0300
+
+#define CPC0_STRP1_PAE_MASK (0x80000000 >> 11)
+#define CPC0_STRP1_PISE_MASK (0x80000000 >> 13)
+
+#define CNTRL_DCR_BASE 0x0b0
+
+#define CPC0_SYS0 (CNTRL_DCR_BASE + 0x30) /* System configuration reg 0 */
+#define CPC0_SYS1 (CNTRL_DCR_BASE + 0x31) /* System configuration reg 1 */
+
+#define CPC0_STRP0 (CNTRL_DCR_BASE + 0x34) /* Power-on config reg 0 (RO) */
+#define CPC0_STRP1 (CNTRL_DCR_BASE + 0x35) /* Power-on config reg 1 (RO) */
+
+#define CPC0_GPIO (CNTRL_DCR_BASE + 0x38) /* GPIO config reg (440GP) */
+
+#define CPC0_CR0 (CNTRL_DCR_BASE + 0x3b) /* Control 0 register */
+#define CPC0_CR1 (CNTRL_DCR_BASE + 0x3a) /* Control 1 register */
+
+#define PLLSYS0_TUNE_MASK 0xffc00000 /* PLL TUNE bits */
+#define PLLSYS0_FB_DIV_MASK 0x003c0000 /* Feedback divisor */
+#define PLLSYS0_FWD_DIV_A_MASK 0x00038000 /* Forward divisor A */
+#define PLLSYS0_FWD_DIV_B_MASK 0x00007000 /* Forward divisor B */
+#define PLLSYS0_OPB_DIV_MASK 0x00000c00 /* OPB divisor */
+#define PLLSYS0_EPB_DIV_MASK 0x00000300 /* EPB divisor */
+#define PLLSYS0_EXTSL_MASK 0x00000080 /* PerClk feedback path */
+#define PLLSYS0_RW_MASK 0x00000060 /* ROM width */
+#define PLLSYS0_RL_MASK 0x00000010 /* ROM location */
+#define PLLSYS0_ZMII_SEL_MASK 0x0000000c /* ZMII selection */
+#define PLLSYS0_BYPASS_MASK 0x00000002 /* Bypass PLL */
+#define PLLSYS0_NTO1_MASK 0x00000001 /* CPU:PLB N-to-1 ratio */
+
+#define PCIL0_BRDGOPT1 (PCIL0_CFGBASE + 0x0040)
+#define PCIL0_BRDGOPT2 (PCIL0_CFGBASE + 0x0044)
+
+#endif /* _PPC440GP_H_ */
diff --git a/arch/powerpc/include/asm/ppc440gx.h b/arch/powerpc/include/asm/ppc440gx.h
new file mode 100644
index 0000000..157e467
--- /dev/null
+++ b/arch/powerpc/include/asm/ppc440gx.h
@@ -0,0 +1,94 @@
+/*
+ * (C) Copyright 2010
+ * Stefan Roese, DENX Software Engineering, sr@denx.de.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef _PPC440GX_H_
+#define _PPC440GX_H_
+
+#define CONFIG_SDRAM_PPC4xx_IBM_DDR /* IBM DDR controller */
+
+/*
+ * Some SoC specific registers (not common for all 440 SoC's)
+ */
+#define GPIO0_BASE (CONFIG_SYS_PERIPHERAL_BASE + 0x00000700)
+
+#define SDR0_PCI0 0x0300
+
+#define SDR0_SDSTP2 0x4001
+#define SDR0_SDSTP3 0x4003
+
+#define SDR0_SDSTP1_PAE_MASK (0x80000000 >> 13)
+#define SDR0_SDSTP1_PISE_MASK (0x80000000 >> 15)
+
+#define SDR0_PFC1_EPS_DECODE(n) ((((u32)(n)) >> 22) & 0x07)
+#define SDR0_PFC1_CTEMS_MASK (0x80000000 >> 11)
+#define SDR0_PFC1_CTEMS_EMS 0x00000000
+#define SDR0_PFC1_CTEMS_CPUTRACE (0x80000000 >> 11)
+
+#define SDR0_MFR_ECS_MASK 0x10000000
+
+#define SDR0_SRST_DMC 0x00200000
+
+#define PLLSYS0_ENG_MASK 0x80000000 /* 0 = SysClk, 1 = PLL VCO */
+#define PLLSYS0_SRC_MASK 0x40000000 /* 0 = PLL A, 1 = PLL B */
+#define PLLSYS0_SEL_MASK 0x38000000 /* 0 = PLL, 1 = CPU, 5 = PerClk */
+#define PLLSYS0_TUNE_MASK 0x07fe0000 /* PLL Tune bits */
+#define PLLSYS0_FB_DIV_MASK 0x0001f000 /* Feedback divisor */
+#define PLLSYS0_FWD_DIV_A_MASK 0x00000f00 /* Fwd Div A */
+#define PLLSYS0_FWD_DIV_B_MASK 0x000000e0 /* Fwd Div B */
+#define PLLSYS0_PRI_DIV_B_MASK 0x0000001c /* PLL Primary Divisor B */
+#define PLLSYS0_OPB_DIV_MASK 0x00000003 /* OPB Divisor */
+
+#define PLLC_ENG_MASK 0x20000000 /* PLL primary forward divisor source */
+#define PLLC_SRC_MASK 0x20000000 /* PLL feedback source */
+#define PLLD_FBDV_MASK 0x1f000000 /* PLL Feedback Divisor */
+#define PLLD_FWDVA_MASK 0x000f0000 /* PLL Forward Divisor A */
+#define PLLD_FWDVB_MASK 0x00000700 /* PLL Forward Divisor B */
+#define PLLD_LFBDV_MASK 0x0000003f /* PLL Local Feedback Divisor */
+
+#define OPBDDV_MASK 0x03000000 /* OPB Clock Divisor Register */
+#define PERDV_MASK 0x07000000 /* Periferal Clock Divisor */
+#define PRADV_MASK 0x07000000 /* Primary Divisor A */
+#define PRBDV_MASK 0x07000000 /* Primary Divisor B */
+#define SPCID_MASK 0x03000000 /* Sync PCI Divisor */
+
+/* Strap 1 Register */
+#define PLLSYS1_LF_DIV_MASK 0xfc000000 /* PLL Local Feedback Divisor */
+#define PLLSYS1_PERCLK_DIV_MASK 0x03000000 /* Peripheral Clk Divisor */
+#define PLLSYS1_MAL_DIV_MASK 0x00c00000 /* MAL Clk Divisor */
+#define PLLSYS1_RW_MASK 0x00300000 /* ROM width */
+#define PLLSYS1_EAR_MASK 0x00080000 /* ERAP Addres reset vector */
+#define PLLSYS1_PAE_MASK 0x00040000 /* PCI arbitor enable */
+#define PLLSYS1_PCHE_MASK 0x00020000 /* PCI host config enable */
+#define PLLSYS1_PISE_MASK 0x00010000 /* PCI init seq. enable */
+#define PLLSYS1_PCWE_MASK 0x00008000 /* PCI local cpu wait enable */
+#define PLLSYS1_PPIM_MASK 0x00007800 /* PCI inbound map */
+#define PLLSYS1_PR64E_MASK 0x00000400 /* PCI init Req64 enable */
+#define PLLSYS1_PXFS_MASK 0x00000300 /* PCI-X Freq Sel */
+#define PLLSYS1_RSVD_MASK 0x00000080 /* RSVD */
+#define PLLSYS1_PDM_MASK 0x00000040 /* PCI-X Driver Mode */
+#define PLLSYS1_EPS_MASK 0x00000038 /* Ethernet Pin Select */
+#define PLLSYS1_RMII_MASK 0x00000004 /* RMII Mode */
+#define PLLSYS1_TRE_MASK 0x00000002 /* GPIO Trace Enable */
+#define PLLSYS1_NTO1_MASK 0x00000001 /* CPU:PLB N-to-1 ratio */
+
+#define PCIL0_BRDGOPT1 (PCIL0_CFGBASE + 0x0040)
+#define PCIL0_BRDGOPT2 (PCIL0_CFGBASE + 0x0044)
+
+#endif /* _PPC440GX_H_ */
diff --git a/arch/powerpc/include/asm/ppc440sp.h b/arch/powerpc/include/asm/ppc440sp.h
new file mode 100644
index 0000000..d4e62b6
--- /dev/null
+++ b/arch/powerpc/include/asm/ppc440sp.h
@@ -0,0 +1,92 @@
+/*
+ * (C) Copyright 2010
+ * Stefan Roese, DENX Software Engineering, sr@denx.de.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef _PPC440SP_H_
+#define _PPC440SP_H_
+
+#define CONFIG_SDRAM_PPC4xx_IBM_DDR2 /* IBM DDR(2) controller */
+
+#define CONFIG_SYS_PPC4xx_PLB4_ARBITER
+
+/*
+ * Some SoC specific registers (not common for all 440 SoC's)
+ */
+#define GPIO0_BASE (CONFIG_SYS_PERIPHERAL_BASE + 0x00000700)
+
+#define SDR0_PCI0 0x0300
+#define SDR0_SDSTP2 0x0022
+#define SDR0_SDSTP3 0x0023
+
+#define SDR0_SDSTP1_PAE_MASK (0x80000000 >> 13)
+#define SDR0_SDSTP1_PISE_MASK (0x80000000 >> 15)
+
+#define SDR0_PFC1_EM_1000 (0x80000000 >> 10)
+
+#define SDR0_MFR_FIXD (0x80000000 >> 3) /* Workaround for PCI/DMA */
+
+#define SDR0_SRST0_DMC 0x00200000
+
+#define PLLSYS0_ENG_MASK 0x80000000 /* 0 = SysClk, 1 = PLL VCO */
+#define PLLSYS0_SRC_MASK 0x40000000 /* 0 = PLL A, 1 = PLL B */
+#define PLLSYS0_SEL_MASK 0x38000000 /* 0 = PLL, 1 = CPU, 5 = PerClk */
+#define PLLSYS0_TUNE_MASK 0x07fe0000 /* PLL Tune bits */
+#define PLLSYS0_FB_DIV_MASK 0x0001f000 /* Feedback divisor */
+#define PLLSYS0_FWD_DIV_A_MASK 0x00000f00 /* Fwd Div A */
+#define PLLSYS0_FWD_DIV_B_MASK 0x000000e0 /* Fwd Div B */
+#define PLLSYS0_PRI_DIV_B_MASK 0x0000001c /* PLL Primary Divisor B */
+#define PLLSYS0_OPB_DIV_MASK 0x00000003 /* OPB Divisor */
+
+#define PLLC_ENG_MASK 0x20000000 /* PLL primary forward divisor source */
+#define PLLC_SRC_MASK 0x20000000 /* PLL feedback source */
+#define PLLD_FBDV_MASK 0x1f000000 /* PLL Feedback Divisor */
+#define PLLD_FWDVA_MASK 0x000f0000 /* PLL Forward Divisor A */
+#define PLLD_FWDVB_MASK 0x00000700 /* PLL Forward Divisor B */
+#define PLLD_LFBDV_MASK 0x0000003f /* PLL Local Feedback Divisor */
+
+#define OPBDDV_MASK 0x03000000 /* OPB Clock Divisor Register */
+#define PERDV_MASK 0x07000000 /* Periferal Clock Divisor */
+#define PRADV_MASK 0x07000000 /* Primary Divisor A */
+#define PRBDV_MASK 0x07000000 /* Primary Divisor B */
+#define SPCID_MASK 0x03000000 /* Sync PCI Divisor */
+
+/* Strap 1 Register */
+#define PLLSYS1_LF_DIV_MASK 0xfc000000 /* PLL Local Feedback Divisor */
+#define PLLSYS1_PERCLK_DIV_MASK 0x03000000 /* Peripheral Clk Divisor */
+#define PLLSYS1_MAL_DIV_MASK 0x00c00000 /* MAL Clk Divisor */
+#define PLLSYS1_RW_MASK 0x00300000 /* ROM width */
+#define PLLSYS1_EAR_MASK 0x00080000 /* ERAP Addres reset vector */
+#define PLLSYS1_PAE_MASK 0x00040000 /* PCI arbitor enable */
+#define PLLSYS1_PCHE_MASK 0x00020000 /* PCI host config enable */
+#define PLLSYS1_PISE_MASK 0x00010000 /* PCI init seq. enable */
+#define PLLSYS1_PCWE_MASK 0x00008000 /* PCI local cpu wait enable */
+#define PLLSYS1_PPIM_MASK 0x00007800 /* PCI inbound map */
+#define PLLSYS1_PR64E_MASK 0x00000400 /* PCI init Req64 enable */
+#define PLLSYS1_PXFS_MASK 0x00000300 /* PCI-X Freq Sel */
+#define PLLSYS1_RSVD_MASK 0x00000080 /* RSVD */
+#define PLLSYS1_PDM_MASK 0x00000040 /* PCI-X Driver Mode */
+#define PLLSYS1_EPS_MASK 0x00000038 /* Ethernet Pin Select */
+#define PLLSYS1_RMII_MASK 0x00000004 /* RMII Mode */
+#define PLLSYS1_TRE_MASK 0x00000002 /* GPIO Trace Enable */
+#define PLLSYS1_NTO1_MASK 0x00000001 /* CPU:PLB N-to-1 ratio */
+
+#define PCIL0_BRDGOPT1 (PCIL0_CFGBASE + 0x0040)
+#define PCIL0_BRDGOPT2 (PCIL0_CFGBASE + 0x0044)
+
+#endif /* _PPC440SP_H_ */
diff --git a/arch/powerpc/include/asm/ppc440spe.h b/arch/powerpc/include/asm/ppc440spe.h
new file mode 100644
index 0000000..a4ab797
--- /dev/null
+++ b/arch/powerpc/include/asm/ppc440spe.h
@@ -0,0 +1,109 @@
+/*
+ * (C) Copyright 2010
+ * Stefan Roese, DENX Software Engineering, sr@denx.de.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef _PPC440SPE_H_
+#define _PPC440SPE_H_
+
+#define CONFIG_SDRAM_PPC4xx_IBM_DDR2 /* IBM DDR(2) controller */
+
+#define CONFIG_SYS_PPC4xx_PLB4_ARBITER
+
+/*
+ * Some SoC specific registers (not common for all 440 SoC's)
+ */
+
+#define GPIO0_BASE (CONFIG_SYS_PERIPHERAL_BASE + 0x00000700)
+
+#define SDR0_PCI0 0x0300
+#define SDR0_SDSTP2 0x0022
+#define SDR0_SDSTP3 0x0023
+
+#define SDR0_SDSTP1_PAE_MASK (0x80000000 >> 13)
+#define SDR0_SDSTP1_PISE_MASK (0x80000000 >> 15)
+#define SDR0_SDSTP1_ERPN_MASK (0x80000000 >> 12)
+#define SDR0_SDSTP1_ERPN_EBC 0
+#define SDR0_SDSTP1_ERPN_PCI (0x80000000 >> 12)
+#define SDR0_SDSTP1_EBCW_MASK (0x80000000 >> 24)
+#define SDR0_SDSTP1_EBCW_8_BITS 0
+#define SDR0_SDSTP1_EBCW_16_BITS (0x80000000 >> 24)
+
+#define SDR0_PFC1_EM_1000 (0x80000000 >> 10)
+
+#define SDR0_MFR_FIXD (0x80000000 >> 3) /* Workaround for PCI/DMA */
+
+#define SDR0_PINSTP_BOOTSTRAP_MASK 0xC0000000 /* Strap Bits */
+#define SDR0_PINSTP_BOOTSTRAP_SETTINGS0 0x00000000 /* Default strap settings 0
+ (EBC boot) */
+#define SDR0_PINSTP_BOOTSTRAP_SETTINGS1 0x40000000 /* Default strap settings 1
+ (PCI boot) */
+#define SDR0_PINSTP_BOOTSTRAP_IIC_54_EN 0x80000000 /* Serial Device Enabled -
+ Addr = 0x54 */
+#define SDR0_PINSTP_BOOTSTRAP_IIC_50_EN 0xC0000000 /* Serial Device Enabled -
+ Addr = 0x50 */
+
+#define SDR0_SRST0_DMC 0x00200000
+
+#define PLLSYS0_ENG_MASK 0x80000000 /* 0 = SysClk, 1 = PLL VCO */
+#define PLLSYS0_SRC_MASK 0x40000000 /* 0 = PLL A, 1 = PLL B */
+#define PLLSYS0_SEL_MASK 0x38000000 /* 0 = PLL, 1 = CPU, 5 = PerClk */
+#define PLLSYS0_TUNE_MASK 0x07fe0000 /* PLL Tune bits */
+#define PLLSYS0_FB_DIV_MASK 0x0001f000 /* Feedback divisor */
+#define PLLSYS0_FWD_DIV_A_MASK 0x00000f00 /* Fwd Div A */
+#define PLLSYS0_FWD_DIV_B_MASK 0x000000e0 /* Fwd Div B */
+#define PLLSYS0_PRI_DIV_B_MASK 0x0000001c /* PLL Primary Divisor B */
+#define PLLSYS0_OPB_DIV_MASK 0x00000003 /* OPB Divisor */
+
+#define PLLC_ENG_MASK 0x20000000 /* PLL primary forward divisor source */
+#define PLLC_SRC_MASK 0x20000000 /* PLL feedback source */
+#define PLLD_FBDV_MASK 0x1f000000 /* PLL Feedback Divisor */
+#define PLLD_FWDVA_MASK 0x000f0000 /* PLL Forward Divisor A */
+#define PLLD_FWDVB_MASK 0x00000700 /* PLL Forward Divisor B */
+#define PLLD_LFBDV_MASK 0x0000003f /* PLL Local Feedback Divisor */
+
+#define OPBDDV_MASK 0x03000000 /* OPB Clock Divisor Register */
+#define PERDV_MASK 0x07000000 /* Periferal Clock Divisor */
+#define PRADV_MASK 0x07000000 /* Primary Divisor A */
+#define PRBDV_MASK 0x07000000 /* Primary Divisor B */
+#define SPCID_MASK 0x03000000 /* Sync PCI Divisor */
+
+/* Strap 1 Register */
+#define PLLSYS1_LF_DIV_MASK 0xfc000000 /* PLL Local Feedback Divisor */
+#define PLLSYS1_PERCLK_DIV_MASK 0x03000000 /* Peripheral Clk Divisor */
+#define PLLSYS1_MAL_DIV_MASK 0x00c00000 /* MAL Clk Divisor */
+#define PLLSYS1_RW_MASK 0x00300000 /* ROM width */
+#define PLLSYS1_EAR_MASK 0x00080000 /* ERAP Addres reset vector */
+#define PLLSYS1_PAE_MASK 0x00040000 /* PCI arbitor enable */
+#define PLLSYS1_PCHE_MASK 0x00020000 /* PCI host config enable */
+#define PLLSYS1_PISE_MASK 0x00010000 /* PCI init seq. enable */
+#define PLLSYS1_PCWE_MASK 0x00008000 /* PCI local cpu wait enable */
+#define PLLSYS1_PPIM_MASK 0x00007800 /* PCI inbound map */
+#define PLLSYS1_PR64E_MASK 0x00000400 /* PCI init Req64 enable */
+#define PLLSYS1_PXFS_MASK 0x00000300 /* PCI-X Freq Sel */
+#define PLLSYS1_RSVD_MASK 0x00000080 /* RSVD */
+#define PLLSYS1_PDM_MASK 0x00000040 /* PCI-X Driver Mode */
+#define PLLSYS1_EPS_MASK 0x00000038 /* Ethernet Pin Select */
+#define PLLSYS1_RMII_MASK 0x00000004 /* RMII Mode */
+#define PLLSYS1_TRE_MASK 0x00000002 /* GPIO Trace Enable */
+#define PLLSYS1_NTO1_MASK 0x00000001 /* CPU:PLB N-to-1 ratio */
+
+#define PCIL0_BRDGOPT1 (PCIL0_CFGBASE + 0x0040)
+#define PCIL0_BRDGOPT2 (PCIL0_CFGBASE + 0x0044)
+
+#endif /* _PPC440SPE_H_ */
diff --git a/arch/powerpc/include/asm/ppc460ex_gt.h b/arch/powerpc/include/asm/ppc460ex_gt.h
new file mode 100644
index 0000000..a535f75
--- /dev/null
+++ b/arch/powerpc/include/asm/ppc460ex_gt.h
@@ -0,0 +1,216 @@
+/*
+ * (C) Copyright 2010
+ * Stefan Roese, DENX Software Engineering, sr@denx.de.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef _PPC460EX_GT_H_
+#define _PPC460EX_GT_H_
+
+#define CONFIG_SDRAM_PPC4xx_IBM_DDR2 /* IBM DDR(2) controller */
+
+#define CONFIG_NAND_NDFC
+
+#define CONFIG_SYS_PPC4xx_PLB4_ARBITER
+
+/*
+ * Some SoC specific registers
+ */
+
+#define GPIO0_BASE (CONFIG_SYS_PERIPHERAL_BASE + 0x00000B00)
+#define GPIO1_BASE (CONFIG_SYS_PERIPHERAL_BASE + 0x00000C00)
+
+/* DCR */
+#define AHB_TOP 0x00a4
+#define AHB_BOT 0x00a5
+
+/* SDR */
+#define SDR0_PCI0 0x01c0
+#define SDR0_AHB_CFG 0x0370
+#define SDR0_USB2HOST_CFG 0x0371
+#define SDR0_ETH_PLL 0x4102
+#define SDR0_ETH_CFG 0x4103
+#define SDR0_ETH_STS 0x4104
+
+/*
+ * Register bits and masks
+ */
+#define SDR0_SDSTP1_PAE_MASK (0x80000000 >> 13)
+#define SDR0_SDSTP1_PISE_MASK (0x80000000 >> 15)
+
+/* CUST0 Customer Configuration Register0 */
+#define SDR0_CUST0_MUX_E_N_G_MASK 0xC0000000 /* Mux_Emac_NDFC_GPIO */
+#define SDR0_CUST0_MUX_EMAC_SEL 0x40000000 /* Emac Selection */
+#define SDR0_CUST0_MUX_NDFC_SEL 0x80000000 /* NDFC Selection */
+#define SDR0_CUST0_MUX_GPIO_SEL 0xC0000000 /* GPIO Selection */
+
+#define SDR0_CUST0_NDFC_EN_MASK 0x20000000 /* NDFC Enable Mask */
+#define SDR0_CUST0_NDFC_ENABLE 0x20000000 /* NDFC Enable */
+#define SDR0_CUST0_NDFC_DISABLE 0x00000000 /* NDFC Disable */
+
+#define SDR0_CUST0_NDFC_BW_MASK 0x10000000 /* NDFC Boot Width */
+#define SDR0_CUST0_NDFC_BW_16_BIT 0x10000000 /* NDFC Boot Width = 16 Bit */
+#define SDR0_CUST0_NDFC_BW_8_BIT 0x00000000 /* NDFC Boot Width = 8 Bit */
+
+#define SDR0_CUST0_NDFC_BP_MASK 0x0F000000 /* NDFC Boot Page */
+#define SDR0_CUST0_NDFC_BP_ENCODE(n) ((((u32)(n)) & 0xF) << 24)
+#define SDR0_CUST0_NDFC_BP_DECODE(n) ((((u32)(n)) >> 24) & 0xF)
+
+#define SDR0_CUST0_NDFC_BAC_MASK 0x00C00000 /* NDFC Boot Address Cycle */
+#define SDR0_CUST0_NDFC_BAC_ENCODE(n) ((((u32)(n)) & 0x3) << 22)
+#define SDR0_CUST0_NDFC_BAC_DECODE(n) ((((u32)(n)) >> 22) & 0x3)
+
+#define SDR0_CUST0_NDFC_ARE_MASK 0x00200000 /* NDFC Auto Read Enable */
+#define SDR0_CUST0_NDFC_ARE_ENABLE 0x00200000 /* NDFC Auto Read Enable */
+#define SDR0_CUST0_NDFC_ARE_DISABLE 0x00000000 /* NDFC Auto Read Disable */
+
+#define SDR0_CUST0_NRB_MASK 0x00100000 /* NDFC Ready / Busy */
+#define SDR0_CUST0_NRB_BUSY 0x00100000 /* Busy */
+#define SDR0_CUST0_NRB_READY 0x00000000 /* Ready */
+
+#define SDR0_CUST0_NDRSC_MASK 0x0000FFF0 /* NDFC Device Reset Count Mask */
+#define SDR0_CUST0_NDRSC_ENCODE(n) ((((u32)(n)) & 0xFFF) << 4)
+#define SDR0_CUST0_NDRSC_DECODE(n) ((((u32)(n)) >> 4) & 0xFFF)
+
+#define SDR0_CUST0_CHIPSELGAT_MASK 0x0000000F /* Chip Select Gating Mask */
+#define SDR0_CUST0_CHIPSELGAT_DIS 0x00000000 /* Chip Select Gating Disable */
+#define SDR0_CUST0_CHIPSELGAT_ENALL 0x0000000F /*All Chip Select Gating Enable*/
+#define SDR0_CUST0_CHIPSELGAT_EN0 0x00000008 /* Chip Select0 Gating Enable */
+#define SDR0_CUST0_CHIPSELGAT_EN1 0x00000004 /* Chip Select1 Gating Enable */
+#define SDR0_CUST0_CHIPSELGAT_EN2 0x00000002 /* Chip Select2 Gating Enable */
+#define SDR0_CUST0_CHIPSELGAT_EN3 0x00000001 /* Chip Select3 Gating Enable */
+
+/* Ethernet PLL Configuration Register (SDR0_ETH_PLL) */
+#define SDR0_ETH_PLL_PLLLOCK 0x80000000 /* Ethernet PLL lock indication */
+
+/* Ethernet Configuration Register (SDR0_ETH_CFG) */
+#define SDR0_ETH_CFG_SGMII3_LPBK 0x00800000 /*SGMII3 port loopback
+ enable */
+#define SDR0_ETH_CFG_SGMII2_LPBK 0x00400000 /*SGMII2 port loopback
+ enable */
+#define SDR0_ETH_CFG_SGMII1_LPBK 0x00200000 /*SGMII1 port loopback
+ enable */
+#define SDR0_ETH_CFG_SGMII0_LPBK 0x00100000 /*SGMII0 port loopback
+ enable */
+#define SDR0_ETH_CFG_SGMII_MASK 0x00070000 /*SGMII Mask */
+#define SDR0_ETH_CFG_SGMII2_ENABLE 0x00040000 /*SGMII2 port enable */
+#define SDR0_ETH_CFG_SGMII1_ENABLE 0x00020000 /*SGMII1 port enable */
+#define SDR0_ETH_CFG_SGMII0_ENABLE 0x00010000 /*SGMII0 port enable */
+#define SDR0_ETH_CFG_TAHOE1_BYPASS 0x00002000 /*TAHOE1 Bypass selector */
+#define SDR0_ETH_CFG_TAHOE0_BYPASS 0x00001000 /*TAHOE0 Bypass selector */
+#define SDR0_ETH_CFG_EMAC3_PHY_CLK_SEL 0x00000800 /*EMAC 3 PHY clock selector*/
+#define SDR0_ETH_CFG_EMAC2_PHY_CLK_SEL 0x00000400 /*EMAC 2 PHY clock selector*/
+#define SDR0_ETH_CFG_EMAC1_PHY_CLK_SEL 0x00000200 /*EMAC 1 PHY clock selector*/
+#define SDR0_ETH_CFG_EMAC0_PHY_CLK_SEL 0x00000100 /*EMAC 0 PHY clock selector*/
+#define SDR0_ETH_CFG_EMAC_2_1_SWAP 0x00000080 /*Swap EMAC2 with EMAC1 */
+#define SDR0_ETH_CFG_EMAC_0_3_SWAP 0x00000040 /*Swap EMAC0 with EMAC3 */
+#define SDR0_ETH_CFG_MDIO_SEL_MASK 0x00000030 /*MDIO source selector mask*/
+#define SDR0_ETH_CFG_MDIO_SEL_EMAC0 0x00000000 /*MDIO source - EMAC0 */
+#define SDR0_ETH_CFG_MDIO_SEL_EMAC1 0x00000010 /*MDIO source - EMAC1 */
+#define SDR0_ETH_CFG_MDIO_SEL_EMAC2 0x00000020 /*MDIO source - EMAC2 */
+#define SDR0_ETH_CFG_MDIO_SEL_EMAC3 0x00000030 /*MDIO source - EMAC3 */
+#define SDR0_ETH_CFG_GMC1_BRIDGE_SEL 0x00000002 /*GMC Port 1 bridge
+ selector */
+#define SDR0_ETH_CFG_GMC0_BRIDGE_SEL 0x00000001 /*GMC Port 0 bridge
+ selector */
+
+#define SDR0_SRST0_BGO 0x80000000 /* PLB to OPB bridge */
+#define SDR0_SRST0_PLB4 0x40000000 /* PLB4 arbiter */
+#define SDR0_SRST0_EBC 0x20000000 /* External bus controller */
+#define SDR0_SRST0_OPB 0x10000000 /* OPB arbiter */
+#define SDR0_SRST0_UART0 0x08000000 /* Universal asynchronous receiver/
+ transmitter 0 */
+#define SDR0_SRST0_UART1 0x04000000 /* Universal asynchronous receiver/
+ transmitter 1 */
+#define SDR0_SRST0_IIC0 0x02000000 /* Inter integrated circuit 0 */
+#define SDR0_SRST0_IIC1 0x01000000 /* Inter integrated circuit 1 */
+#define SDR0_SRST0_GPIO0 0x00800000 /* General purpose I/O 0 */
+#define SDR0_SRST0_GPT 0x00400000 /* General purpose timer */
+#define SDR0_SRST0_DMC 0x00200000 /* DDR SDRAM memory controller */
+#define SDR0_SRST0_PCI 0x00100000 /* PCI */
+#define SDR0_SRST0_CPM0 0x00020000 /* Clock and power management */
+#define SDR0_SRST0_IMU 0x00010000 /* I2O DMA */
+#define SDR0_SRST0_UIC0 0x00008000 /* Universal interrupt controller 0*/
+#define SDR0_SRST0_UIC1 0x00004000 /* Universal interrupt controller 1*/
+#define SDR0_SRST0_SRAM 0x00002000 /* Universal interrupt controller 0*/
+#define SDR0_SRST0_UIC2 0x00001000 /* Universal interrupt controller 2*/
+#define SDR0_SRST0_UIC3 0x00000800 /* Universal interrupt controller 3*/
+#define SDR0_SRST0_OCM 0x00000400 /* Universal interrupt controller 0*/
+#define SDR0_SRST0_UART2 0x00000200 /* Universal asynchronous receiver/
+ transmitter 2 */
+#define SDR0_SRST0_MAL 0x00000100 /* Media access layer */
+#define SDR0_SRST0_GPTR 0x00000040 /* General purpose timer */
+#define SDR0_SRST0_L2CACHE 0x00000004 /* L2 Cache */
+#define SDR0_SRST0_UART3 0x00000002 /* Universal asynchronous receiver/
+ transmitter 3 */
+#define SDR0_SRST0_GPIO1 0x00000001 /* General purpose I/O 1 */
+
+#define SDR0_SRST1_RLL 0x80000000 /* SRIO RLL */
+#define SDR0_SRST1_SCP 0x40000000 /* Serial communications port */
+#define SDR0_SRST1_PLBARB 0x20000000 /* PLB Arbiter */
+#define SDR0_SRST1_EIPPKP 0x10000000 /* EIPPPKP */
+#define SDR0_SRST1_EIP94 0x08000000 /* EIP 94 */
+#define SDR0_SRST1_EMAC0 0x04000000 /* Ethernet media access
+ controller 0 */
+#define SDR0_SRST1_EMAC1 0x02000000 /* Ethernet media access
+ controller 1 */
+#define SDR0_SRST1_EMAC2 0x01000000 /* Ethernet media access
+ controller 2 */
+#define SDR0_SRST1_EMAC3 0x00800000 /* Ethernet media access
+ controller 3 */
+#define SDR0_SRST1_ZMII 0x00400000 /* Ethernet ZMII/RMII/SMII */
+#define SDR0_SRST1_RGMII0 0x00200000 /* Ethernet RGMII/RTBI 0 */
+#define SDR0_SRST1_RGMII1 0x00100000 /* Ethernet RGMII/RTBI 1 */
+#define SDR0_SRST1_DMA4 0x00080000 /* DMA to PLB4 */
+#define SDR0_SRST1_DMA4CH 0x00040000 /* DMA Channel to PLB4 */
+#define SDR0_SRST1_SATAPHY 0x00020000 /* Serial ATA PHY */
+#define SDR0_SRST1_SRIODEV 0x00010000 /* Serial Rapid IO core, PCS, and
+ serdes */
+#define SDR0_SRST1_SRIOPCS 0x00008000 /* Serial Rapid IO core and PCS */
+#define SDR0_SRST1_NDFC 0x00004000 /* Nand flash controller */
+#define SDR0_SRST1_SRIOPLB 0x00002000 /* Serial Rapid IO PLB */
+#define SDR0_SRST1_ETHPLL 0x00001000 /* Ethernet PLL */
+#define SDR0_SRST1_TAHOE1 0x00000800 /* Ethernet Tahoe 1 */
+#define SDR0_SRST1_TAHOE0 0x00000400 /* Ethernet Tahoe 0 */
+#define SDR0_SRST1_SGMII0 0x00000200 /* Ethernet SGMII 0 */
+#define SDR0_SRST1_SGMII1 0x00000100 /* Ethernet SGMII 1 */
+#define SDR0_SRST1_SGMII2 0x00000080 /* Ethernet SGMII 2 */
+#define SDR0_SRST1_AHB 0x00000040 /* PLB4XAHB bridge */
+#define SDR0_SRST1_USBOTGPHY 0x00000020 /* USB 2.0 OTG PHY */
+#define SDR0_SRST1_USBOTG 0x00000010 /* USB 2.0 OTG controller */
+#define SDR0_SRST1_USBHOST 0x00000008 /* USB 2.0 Host controller */
+#define SDR0_SRST1_AHBDMAC 0x00000004 /* AHB DMA controller */
+#define SDR0_SRST1_AHBICM 0x00000002 /* AHB inter-connect matrix */
+#define SDR0_SRST1_SATA 0x00000001 /* Serial ATA controller */
+
+#define PLLSYS0_FWD_DIV_A_MASK 0x000000f0 /* Fwd Div A */
+#define PLLSYS0_FWD_DIV_B_MASK 0x0000000f /* Fwd Div B */
+#define PLLSYS0_FB_DIV_MASK 0x0000ff00 /* Feedback divisor */
+#define PLLSYS0_OPB_DIV_MASK 0x0c000000 /* OPB Divisor */
+#define PLLSYS0_PLBEDV0_DIV_MASK 0xe0000000 /* PLB Early Clock Divisor */
+#define PLLSYS0_PERCLK_DIV_MASK 0x03000000 /* Peripheral Clk Divisor */
+#define PLLSYS0_SEL_MASK 0x18000000 /* 0 = PLL, 1 = PerClk */
+
+#define CPR0_ICFG_RLI_MASK 0x80000000
+
+#define CPR0_PLLC_RST 0x80000000
+#define CPR0_PLLC_ENG 0x40000000
+
+#define PCIL0_BRDGOPT1 (PCIL0_CFGBASE + 0x0040)
+#define PCIL0_BRDGOPT2 (PCIL0_CFGBASE + 0x0044)
+
+#endif /* _PPC460EX_GT_H_ */
diff --git a/arch/powerpc/include/asm/ppc460sx.h b/arch/powerpc/include/asm/ppc460sx.h
new file mode 100644
index 0000000..08ea7c4
--- /dev/null
+++ b/arch/powerpc/include/asm/ppc460sx.h
@@ -0,0 +1,40 @@
+/*
+ * (C) Copyright 2010
+ * Stefan Roese, DENX Software Engineering, sr@denx.de.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef _PPC460SX_H_
+#define _PPC460SX_H_
+
+#define CONFIG_SDRAM_PPC4xx_IBM_DDR2 /* IBM DDR(2) controller */
+
+#define CONFIG_SYS_PPC4xx_PLB4_ARBITER
+
+#define GPIO0_BASE (CONFIG_SYS_PERIPHERAL_BASE + 0x00000700)
+
+#define SDR0_SRST0_DMC 0x00200000
+
+#define PLLSYS0_FWD_DIV_A_MASK 0x000000f0 /* Fwd Div A */
+#define PLLSYS0_FWD_DIV_B_MASK 0x0000000f /* Fwd Div B */
+#define PLLSYS0_FB_DIV_MASK 0x0000ff00 /* Feedback divisor */
+#define PLLSYS0_OPB_DIV_MASK 0x0c000000 /* OPB Divisor */
+#define PLLSYS0_PLBEDV0_DIV_MASK 0xe0000000 /* PLB Early Clock Divisor */
+#define PLLSYS0_PERCLK_DIV_MASK 0x03000000 /* Peripheral Clk Divisor */
+#define PLLSYS0_SEL_MASK 0x18000000 /* 0 = PLL, 1 = PerClk */
+
+#endif /* _PPC460SX_H_ */
diff --git a/arch/powerpc/include/asm/ppc4xx-emac.h b/arch/powerpc/include/asm/ppc4xx-emac.h
index 2b51453..25a0512 100644
--- a/arch/powerpc/include/asm/ppc4xx-emac.h
+++ b/arch/powerpc/include/asm/ppc4xx-emac.h
@@ -149,12 +149,6 @@
#define EMAC_STACR_OC_MASK (0x00000000)
#endif
-#if defined(CONFIG_440SP) || defined(CONFIG_440SPE) || \
- defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \
- defined(CONFIG_405EX)
-#define SDR0_PFC1_EM_1000 (0x00200000)
-#endif
-
/*
* XMII bridge configurations for those systems (e.g. 405EX(r)) that do
* not have a pin function control (PFC) register to otherwise determine
diff --git a/arch/powerpc/include/asm/ppc4xx-mal.h b/arch/powerpc/include/asm/ppc4xx-mal.h
index 1ca9429..7198685 100644
--- a/arch/powerpc/include/asm/ppc4xx-mal.h
+++ b/arch/powerpc/include/asm/ppc4xx-mal.h
@@ -42,6 +42,45 @@
+----------------------------------------------------------------------------*/
#ifndef _mal_h_
#define _mal_h_
+
+#if !defined(MAL_DCR_BASE)
+#define MAL_DCR_BASE 0x180
+#endif
+#define MAL0_CFG (MAL_DCR_BASE + 0x00) /* MAL Config reg */
+#define MAL0_ESR (MAL_DCR_BASE + 0x01) /* Error Status (Read/Clear) */
+#define MAL0_IER (MAL_DCR_BASE + 0x02) /* Interrupt enable */
+#define MAL0_TXCASR (MAL_DCR_BASE + 0x04) /* TX Channel active (set) */
+#define MAL0_TXCARR (MAL_DCR_BASE + 0x05) /* TX Channel active (reset) */
+#define MAL0_TXEOBISR (MAL_DCR_BASE + 0x06) /* TX End of buffer int status*/
+#define MAL0_TXDEIR (MAL_DCR_BASE + 0x07) /* TX Descr. Error Int */
+#define MAL0_TXBADDR (MAL_DCR_BASE + 0x09) /* TX descriptor base addr*/
+#define MAL0_RXCASR (MAL_DCR_BASE + 0x10) /* RX Channel active (set) */
+#define MAL0_RXCARR (MAL_DCR_BASE + 0x11) /* RX Channel active (reset) */
+#define MAL0_RXEOBISR (MAL_DCR_BASE + 0x12) /* RX End of buffer int status*/
+#define MAL0_RXDEIR (MAL_DCR_BASE + 0x13) /* RX Descr. Error Int */
+#define MAL0_RXBADDR (MAL_DCR_BASE + 0x15) /* RX descriptor base addr */
+#define MAL0_TXCTP0R (MAL_DCR_BASE + 0x20) /* TX 0 Channel table pointer */
+#define MAL0_TXCTP1R (MAL_DCR_BASE + 0x21) /* TX 1 Channel table pointer */
+#define MAL0_TXCTP2R (MAL_DCR_BASE + 0x22) /* TX 2 Channel table pointer */
+#define MAL0_TXCTP3R (MAL_DCR_BASE + 0x23) /* TX 3 Channel table pointer */
+#define MAL0_RXCTP0R (MAL_DCR_BASE + 0x40) /* RX 0 Channel table pointer */
+#define MAL0_RXCTP1R (MAL_DCR_BASE + 0x41) /* RX 1 Channel table pointer */
+#define MAL0_RCBS0 (MAL_DCR_BASE + 0x60) /* RX 0 Channel buffer size */
+#define MAL0_RCBS1 (MAL_DCR_BASE + 0x61) /* RX 1 Channel buffer size */
+#if defined(CONFIG_440GX) || \
+ defined(CONFIG_460EX) || defined(CONFIG_460GT)
+#define MAL0_RXCTP2R (MAL_DCR_BASE + 0x42) /* RX 2 Channel table pointer */
+#define MAL0_RXCTP3R (MAL_DCR_BASE + 0x43) /* RX 3 Channel table pointer */
+#define MAL0_RXCTP8R (MAL_DCR_BASE + 0x48) /* RX 8 Channel table pointer */
+#define MAL0_RXCTP16R (MAL_DCR_BASE + 0x50) /* RX 16 Channel table pointer*/
+#define MAL0_RXCTP24R (MAL_DCR_BASE + 0x58) /* RX 24 Channel table pointer*/
+#define MAL0_RCBS2 (MAL_DCR_BASE + 0x62) /* RX 2 Channel buffer size */
+#define MAL0_RCBS3 (MAL_DCR_BASE + 0x63) /* RX 3 Channel buffer size */
+#define MAL0_RCBS8 (MAL_DCR_BASE + 0x68) /* RX 8 Channel buffer size */
+#define MAL0_RCBS16 (MAL_DCR_BASE + 0x70) /* RX 16 Channel buffer size */
+#define MAL0_RCBS24 (MAL_DCR_BASE + 0x78) /* RX 24 Channel buffer size */
+#endif /* CONFIG_440GX */
+
/* MADMAL transmit and receive status/control bits */
/* for COMMAC bits, refer to the COMMAC header file */
diff --git a/arch/powerpc/include/asm/ppc4xx-sdram.h b/arch/powerpc/include/asm/ppc4xx-sdram.h
index 4ec1ef8..ac150c2 100644
--- a/arch/powerpc/include/asm/ppc4xx-sdram.h
+++ b/arch/powerpc/include/asm/ppc4xx-sdram.h
@@ -951,8 +951,6 @@
#define SDRAM_RTSR_TRK1SM_ATPLS1 0x80000000 /* atpls1 state */
#define SDRAM_RTSR_TRK1SM_RESET 0xC0000000 /* reset state */
-#define SDR0_MFR_FIXD 0x10000000 /* Workaround for PCI/DMA */
-
#endif /* CONFIG_SDRAM_PPC4xx_IBM_DDR2 */
#if defined(CONFIG_SDRAM_PPC4xx_DENALI_DDR2)
diff --git a/arch/powerpc/include/asm/ppc4xx.h b/arch/powerpc/include/asm/ppc4xx.h
index ca04bb4..7aff401 100644
--- a/arch/powerpc/include/asm/ppc4xx.h
+++ b/arch/powerpc/include/asm/ppc4xx.h
@@ -25,79 +25,113 @@
#define __PPC4XX_H__
/*
- * Configure which SDRAM/DDR/DDR2 controller is equipped
+ * Include SoC specific headers
*/
-#if defined(CONFIG_405GP) || defined(CONFIG_405CR) || defined(CONFIG_405EP) || \
- defined(CONFIG_AP1000) || defined(CONFIG_ML2)
-#define CONFIG_SDRAM_PPC4xx_IBM_SDRAM /* IBM SDRAM controller */
+#if defined(CONFIG_405CR)
+#include <asm/ppc405cr.h>
#endif
-#if defined(CONFIG_440GP) || defined(CONFIG_440GX) || \
- defined(CONFIG_440EP) || defined(CONFIG_440GR)
-#define CONFIG_SDRAM_PPC4xx_IBM_DDR /* IBM DDR controller */
+#if defined(CONFIG_405EP)
+#include <asm/ppc405ep.h>
+#endif
+
+#if defined(CONFIG_405EX)
+#include <asm/ppc405ex.h>
+#endif
+
+#if defined(CONFIG_405EZ)
+#include <asm/ppc405ez.h>
+#endif
+
+#if defined(CONFIG_405GP)
+#include <asm/ppc405gp.h>
+#endif
+
+#if defined(CONFIG_440EP) || defined(CONFIG_440GR)
+#include <asm/ppc440ep_gr.h>
#endif
#if defined(CONFIG_440EPX) || defined(CONFIG_440GRX)
-#define CONFIG_SDRAM_PPC4xx_DENALI_DDR2 /* Denali DDR(2) controller */
+#include <asm/ppc440epx_grx.h>
#endif
-#if defined(CONFIG_405EX) || \
- defined(CONFIG_440SP) || defined(CONFIG_440SPE) || \
- defined(CONFIG_460EX) || defined(CONFIG_460GT) || \
- defined(CONFIG_460SX)
-#define CONFIG_SDRAM_PPC4xx_IBM_DDR2 /* IBM DDR(2) controller */
+#if defined(CONFIG_440GP)
+#include <asm/ppc440gp.h>
#endif
-#if defined(CONFIG_440EP) || defined(CONFIG_440GR) || \
- defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \
- defined(CONFIG_405EZ) || defined(CONFIG_405EX) || \
- defined(CONFIG_460EX) || defined(CONFIG_460GT)
-#define CONFIG_NAND_NDFC
+#if defined(CONFIG_440GX)
+#include <asm/ppc440gx.h>
#endif
-/* PLB4 CrossBar Arbiter Core supported across PPC4xx families */
-#if defined(CONFIG_405EX) || \
- defined(CONFIG_440EP) || defined(CONFIG_440EPX) || \
- defined(CONFIG_440GR) || defined(CONFIG_440GRX) || \
- defined(CONFIG_440SP) || defined(CONFIG_440SPE) || \
- defined(CONFIG_460EX) || defined(CONFIG_460GT) || \
- defined(CONFIG_460SX)
+#if defined(CONFIG_440SP)
+#include <asm/ppc440sp.h>
+#endif
-#define PLB_ARBITER_BASE 0x80
+#if defined(CONFIG_440SPE)
+#include <asm/ppc440spe.h>
+#endif
-#define PLB0_ACR (PLB_ARBITER_BASE + 0x01)
-#define PLB0_ACR_PPM_MASK 0xF0000000
-#define PLB0_ACR_PPM_FIXED 0x00000000
-#define PLB0_ACR_PPM_FAIR 0xD0000000
-#define PLB0_ACR_HBU_MASK 0x08000000
-#define PLB0_ACR_HBU_DISABLED 0x00000000
-#define PLB0_ACR_HBU_ENABLED 0x08000000
-#define PLB0_ACR_RDP_MASK 0x06000000
-#define PLB0_ACR_RDP_DISABLED 0x00000000
-#define PLB0_ACR_RDP_2DEEP 0x02000000
-#define PLB0_ACR_RDP_3DEEP 0x04000000
-#define PLB0_ACR_RDP_4DEEP 0x06000000
-#define PLB0_ACR_WRP_MASK 0x01000000
-#define PLB0_ACR_WRP_DISABLED 0x00000000
-#define PLB0_ACR_WRP_2DEEP 0x01000000
+#if defined(CONFIG_460EX) || defined(CONFIG_460GT)
+#include <asm/ppc460ex_gt.h>
+#endif
-#define PLB1_ACR (PLB_ARBITER_BASE + 0x09)
-#define PLB1_ACR_PPM_MASK 0xF0000000
-#define PLB1_ACR_PPM_FIXED 0x00000000
-#define PLB1_ACR_PPM_FAIR 0xD0000000
-#define PLB1_ACR_HBU_MASK 0x08000000
-#define PLB1_ACR_HBU_DISABLED 0x00000000
-#define PLB1_ACR_HBU_ENABLED 0x08000000
-#define PLB1_ACR_RDP_MASK 0x06000000
-#define PLB1_ACR_RDP_DISABLED 0x00000000
-#define PLB1_ACR_RDP_2DEEP 0x02000000
-#define PLB1_ACR_RDP_3DEEP 0x04000000
-#define PLB1_ACR_RDP_4DEEP 0x06000000
-#define PLB1_ACR_WRP_MASK 0x01000000
-#define PLB1_ACR_WRP_DISABLED 0x00000000
-#define PLB1_ACR_WRP_2DEEP 0x01000000
+#if defined(CONFIG_460SX)
+#include <asm/ppc460sx.h>
+#endif
-#endif /* 440EP/EPX 440GR/GRX 440SP/SPE 460EX/GT/SX 405EX*/
+/*
+ * Configure which SDRAM/DDR/DDR2 controller is equipped
+ */
+// test-only: what to do with these???
+#if defined(CONFIG_AP1000) || defined(CONFIG_ML2)
+#define CONFIG_SDRAM_PPC4xx_IBM_SDRAM /* IBM SDRAM controller */
+#endif
+
+/*
+ * Common registers for all SoC's
+ */
+/* DCR registers */
+#define PLB3A0_ACR 0x0077
+#define PLB4A0_ACR 0x0081
+#define PLB4A1_ACR 0x0089
+
+#define PLB4Ax_ACR_PPM_MASK 0xf0000000
+#define PLB4Ax_ACR_PPM_FIXED 0x00000000
+#define PLB4Ax_ACR_PPM_FAIR 0xd0000000
+#define PLB4Ax_ACR_HBU_MASK 0x08000000
+#define PLB4Ax_ACR_HBU_DISABLED 0x00000000
+#define PLB4Ax_ACR_HBU_ENABLED 0x08000000
+#define PLB4Ax_ACR_RDP_MASK 0x06000000
+#define PLB4Ax_ACR_RDP_DISABLED 0x00000000
+#define PLB4Ax_ACR_RDP_2DEEP 0x02000000
+#define PLB4Ax_ACR_RDP_3DEEP 0x04000000
+#define PLB4Ax_ACR_RDP_4DEEP 0x06000000
+#define PLB4Ax_ACR_WRP_MASK 0x01000000
+#define PLB4Ax_ACR_WRP_DISABLED 0x00000000
+#define PLB4Ax_ACR_WRP_2DEEP 0x01000000
+
+/* General Purpose Timer (GPT) Register Offsets */
+#define GPT0_TBC 0x00000000
+#define GPT0_IM 0x00000018
+#define GPT0_ISS 0x0000001C
+#define GPT0_ISC 0x00000020
+#define GPT0_IE 0x00000024
+#define GPT0_COMP0 0x00000080
+#define GPT0_COMP1 0x00000084
+#define GPT0_COMP2 0x00000088
+#define GPT0_COMP3 0x0000008C
+#define GPT0_COMP4 0x00000090
+#define GPT0_COMP5 0x00000094
+#define GPT0_COMP6 0x00000098
+#define GPT0_MASK0 0x000000C0
+#define GPT0_MASK1 0x000000C4
+#define GPT0_MASK2 0x000000C8
+#define GPT0_MASK3 0x000000CC
+#define GPT0_MASK4 0x000000D0
+#define GPT0_MASK5 0x000000D4
+#define GPT0_MASK6 0x000000D8
+#define GPT0_DCT0 0x00000110
+#define GPT0_DCIS 0x0000011C
#if defined(CONFIG_440)
#include <asm/ppc440.h>
diff --git a/board/amcc/bamboo/bamboo.c b/board/amcc/bamboo/bamboo.c
index 41957c9..d4205e0 100644
--- a/board/amcc/bamboo/bamboo.c
+++ b/board/amcc/bamboo/bamboo.c
@@ -554,7 +554,7 @@
|
+-------------------------------------------------------------------------*/
/* Read Pin Strap Register in PPC440EP */
- mfsdr(sdr_pstrp0, sdr0_pstrp0);
+ mfsdr(SDR0_PINSTP, sdr0_pstrp0);
bootstrap_settings = sdr0_pstrp0 & SDR0_PSTRP0_BOOTSTRAP_MASK;
/*-------------------------------------------------------------------------+
diff --git a/board/amcc/bamboo/bamboo.h b/board/amcc/bamboo/bamboo.h
index 4474862..f2b78a9 100644
--- a/board/amcc/bamboo/bamboo.h
+++ b/board/amcc/bamboo/bamboo.h
@@ -110,17 +110,6 @@
/*----------------------------------------------------------------------------+
| SDR Configuration registers
+----------------------------------------------------------------------------*/
-/* Serial Device Strap Reg 0 */
-#define SDR0_SDSTP0 0x0020
-/* Serial Device Strap Reg 1 */
-#define SDR0_SDSTP1 0x0021
-/* Serial Device Strap Reg 2 */
-#define SDR0_SDSTP2 SDR0_STRP2
-/* Serial Device Strap Reg 3 */
-#define SDR0_SDSTP3 SDR0_STRP3
-
-#define sdr_pstrp0 0x0040
-
#define SDR0_SDSTP1_EBC_ROM_BS_MASK 0x00006000 /* EBC Boot Size Mask */
#define SDR0_SDSTP1_EBC_ROM_BS_32BIT 0x00004000 /* EBC 32 bits */
#define SDR0_SDSTP1_EBC_ROM_BS_16BIT 0x00002000 /* EBC 16 Bits */
diff --git a/board/amcc/bamboo/flash.c b/board/amcc/bamboo/flash.c
index 406342f..07d185f 100644
--- a/board/amcc/bamboo/flash.c
+++ b/board/amcc/bamboo/flash.c
@@ -86,7 +86,7 @@
unsigned long ebc_boot_size;
unsigned long boot_selection;
- mfsdr(sdr_pstrp0, val);
+ mfsdr(SDR0_PINSTP, val);
index = (val & SDR0_PSTRP0_BOOTSTRAP_MASK) >> 29;
if ((index == 5) || (index == 7)) {
diff --git a/board/amcc/sequoia/sequoia.c b/board/amcc/sequoia/sequoia.c
index 4338e6b..c523bca 100644
--- a/board/amcc/sequoia/sequoia.c
+++ b/board/amcc/sequoia/sequoia.c
@@ -321,8 +321,8 @@
* This fix will make the MAL burst disabling patch for the Linux
* EMAC driver obsolete.
*/
- reg = mfdcr(PLB4_ACR) & ~PLB4_ACR_WRP;
- mtdcr(PLB4_ACR, reg);
+ reg = mfdcr(PLB4A0_ACR) & ~PLB4Ax_ACR_WRP_MASK;
+ mtdcr(PLB4A0_ACR, reg);
return 0;
}
diff --git a/board/esd/du440/du440.c b/board/esd/du440/du440.c
index fccfaee..426321e 100644
--- a/board/esd/du440/du440.c
+++ b/board/esd/du440/du440.c
@@ -265,8 +265,8 @@
* This fix will make the MAL burst disabling patch for the Linux
* EMAC driver obsolete.
*/
- reg = mfdcr(PLB4_ACR) & ~PLB4_ACR_WRP;
- mtdcr(PLB4_ACR, reg);
+ reg = mfdcr(PLB4A0_ACR) & ~PLB4Ax_ACR_WRP_MASK;
+ mtdcr(PLB4A0_ACR, reg);
/*
* release IO-RST#
diff --git a/board/esd/pci405/pci405.c b/board/esd/pci405/pci405.c
index dd97c7a..4018a7d 100644
--- a/board/esd/pci405/pci405.c
+++ b/board/esd/pci405/pci405.c
@@ -281,7 +281,6 @@
#define PCI0_BRDGOPT1 0x4a
pci_write_config_word(PCIDEVID_405GP, PCI0_BRDGOPT1, 0x3f20);
-#define PLB0_ACR 0x87
/*
* Enable fairness and high bus utilization
*/
diff --git a/board/esd/pmc440/pmc440.c b/board/esd/pmc440/pmc440.c
index c907b85..8238c33 100644
--- a/board/esd/pmc440/pmc440.c
+++ b/board/esd/pmc440/pmc440.c
@@ -426,8 +426,8 @@
* This fix will make the MAL burst disabling patch for the Linux
* EMAC driver obsolete.
*/
- reg = mfdcr(PLB4_ACR) & ~PLB4_ACR_WRP;
- mtdcr(PLB4_ACR, reg);
+ reg = mfdcr(PLB4A0_ACR) & ~PLB4Ax_ACR_WRP_MASK;
+ mtdcr(PLB4A0_ACR, reg);
#ifdef CONFIG_FPGA
pmc440_init_fpga();
diff --git a/board/korat/korat.c b/board/korat/korat.c
index afa36d6..4f0513a 100644
--- a/board/korat/korat.c
+++ b/board/korat/korat.c
@@ -553,8 +553,8 @@
* This fix will make the MAL burst disabling patch for the Linux
* EMAC driver obsolete.
*/
- reg = mfdcr(PLB4_ACR) & ~PLB4_ACR_WRP;
- mtdcr(PLB4_ACR, reg);
+ reg = mfdcr(PLB4A0_ACR) & ~PLB4Ax_ACR_WRP_MASK;
+ mtdcr(PLB4A0_ACR, reg);
set_serial_number();
set_mac_addresses();
diff --git a/board/lwmon5/lwmon5.c b/board/lwmon5/lwmon5.c
index 0c6f4e5..9622b70 100644
--- a/board/lwmon5/lwmon5.c
+++ b/board/lwmon5/lwmon5.c
@@ -38,8 +38,8 @@
u32 reg;
/* PLB Write pipelining disabled. Denali Core workaround */
- mtdcr(PLB0_ACR, 0xDE000000);
- mtdcr(PLB1_ACR, 0xDE000000);
+ mtdcr(PLB4A0_ACR, 0xDE000000);
+ mtdcr(PLB4A1_ACR, 0xDE000000);
/*--------------------------------------------------------------------
* Setup the interrupt controller polarities, triggers, etc.
@@ -249,8 +249,8 @@
* This fix will make the MAL burst disabling patch for the Linux
* EMAC driver obsolete.
*/
- reg = mfdcr(PLB4_ACR) & ~PLB4_ACR_WRP;
- mtdcr(PLB4_ACR, reg);
+ reg = mfdcr(PLB4A0_ACR) & ~PLB4Ax_ACR_WRP_MASK;
+ mtdcr(PLB4A0_ACR, reg);
/*
* Init matrix keyboard
diff --git a/board/netstal/hcu5/hcu5.c b/board/netstal/hcu5/hcu5.c
index b15f99e..f94d05b 100644
--- a/board/netstal/hcu5/hcu5.c
+++ b/board/netstal/hcu5/hcu5.c
@@ -327,7 +327,7 @@
u32 reg;
mfsdr(SDR0_PCI0, reg);
- return (reg & SDR0_XCR_PAE_MASK);
+ return (reg & SDR0_PCI0_PAE_MASK);
}
/*
@@ -352,28 +352,28 @@
* Set priority for all PLB3 devices to 0.
* Set PLB3 arbiter to fair mode.
*/
- mfsdr(SD0_AMP1, addr);
- mtsdr(SD0_AMP1, (addr & 0x000000FF) | 0x0000FF00);
- addr = mfdcr(PLB3_ACR);
- mtdcr(PLB3_ACR, addr | 0x80000000); /* Sequoia */
+ mfsdr(SDR0_AMP1, addr);
+ mtsdr(SDR0_AMP1, (addr & 0x000000FF) | 0x0000FF00);
+ addr = mfdcr(PLB3A0_ACR);
+ mtdcr(PLB3A0_ACR, addr | 0x80000000); /* Sequoia */
/*
* Set priority for all PLB4 devices to 0.
*/
- mfsdr(SD0_AMP0, addr);
- mtsdr(SD0_AMP0, (addr & 0x000000FF) | 0x0000FF00);
- addr = mfdcr(PLB4_ACR) | 0xa0000000; /* Was 0x8---- */
- mtdcr(PLB4_ACR, addr); /* Sequoia */
+ mfsdr(SDR0_AMP0, addr);
+ mtsdr(SDR0_AMP0, (addr & 0x000000FF) | 0x0000FF00);
+ addr = mfdcr(PLB4A0_ACR) | 0xa0000000; /* Was 0x8---- */
+ mtdcr(PLB4A0_ACR, addr); /* Sequoia */
/*
* As of errata version 0.4, CHIP_8: Incorrect Write to DDR SDRAM.
* Workaround: Disable write pipelining to DDR SDRAM by setting
- * PLB0_ACR[WRP] = 0.
+ * PLB4A0_ACR[WRP] = 0.
*/
- mtdcr(PLB0_ACR, 0); /* PATCH HAB: WRITE PIPELINING OFF */
+ mtdcr(PLB4A0_ACR, 0); /* PATCH HAB: WRITE PIPELINING OFF */
/* Segment1 */
- mtdcr(PLB1_ACR, 0); /* PATCH HAB: WRITE PIPELINING OFF */
+ mtdcr(PLB4A1_ACR, 0); /* PATCH HAB: WRITE PIPELINING OFF */
return board_with_pci();
}
diff --git a/drivers/net/4xx_enet.c b/drivers/net/4xx_enet.c
index bc9211e..45ff4f3 100644
--- a/drivers/net/4xx_enet.c
+++ b/drivers/net/4xx_enet.c
@@ -1494,8 +1494,7 @@
/* set speed */
if (speed == _1000BASET) {
-#if defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \
- defined(CONFIG_440SP) || defined(CONFIG_440SPE)
+#if defined(CONFIG_440SP) || defined(CONFIG_440SPE)
unsigned long pfc1;
mfsdr (SDR0_PFC1, pfc1);
diff --git a/include/configs/PPChameleonEVB.h b/include/configs/PPChameleonEVB.h
index 44f03dc..09f3544 100644
--- a/include/configs/PPChameleonEVB.h
+++ b/include/configs/PPChameleonEVB.h
@@ -577,17 +577,6 @@
#define DIMM_READ_ADDR 0xAB
#define DIMM_WRITE_ADDR 0xAA
-#define CPC0_PLLMR0 (CNTRL_DCR_BASE+0x0) /* PLL mode 0 register */
-#define CPC0_BOOT (CNTRL_DCR_BASE+0x1) /* Chip Clock Status register */
-#define CPC0_CR1 (CNTRL_DCR_BASE+0x2) /* Chip Control 1 register */
-#define CPC0_EPRCSR (CNTRL_DCR_BASE+0x3) /* EMAC PHY Rcv Clk Src register */
-#define CPC0_PLLMR1 (CNTRL_DCR_BASE+0x4) /* PLL mode 1 register */
-#define CPC0_UCR (CNTRL_DCR_BASE+0x5) /* UART Control register */
-#define CPC0_SRR (CNTRL_DCR_BASE+0x6) /* Soft Reset register */
-#define CPC0_JTAGID (CNTRL_DCR_BASE+0x7) /* JTAG ID register */
-#define CPC0_SPARE (CNTRL_DCR_BASE+0x8) /* Spare DCR */
-#define CPC0_PCI (CNTRL_DCR_BASE+0x9) /* PCI Control register */
-
/* Defines for CPC0_PLLMR1 Register fields */
#define PLL_ACTIVE 0x80000000
#define CPC0_PLLMR1_SSCS 0x80000000
diff --git a/nand_spl/board/amcc/canyonlands/ddr2_fixed.c b/nand_spl/board/amcc/canyonlands/ddr2_fixed.c
index 9440c1e..f71ecfb9 100644
--- a/nand_spl/board/amcc/canyonlands/ddr2_fixed.c
+++ b/nand_spl/board/amcc/canyonlands/ddr2_fixed.c
@@ -57,7 +57,7 @@
/*
* Reset the DDR-SDRAM controller.
*/
- mtsdr(SDR0_SRST, (0x80000000 >> 10));
+ mtsdr(SDR0_SRST, SDR0_SRST0_DMC);
mtsdr(SDR0_SRST, 0x00000000);
/*