diff --git a/arch/powerpc/cpu/mpc83xx/Kconfig b/arch/powerpc/cpu/mpc83xx/Kconfig
index 2a1abe0..69a600c 100644
--- a/arch/powerpc/cpu/mpc83xx/Kconfig
+++ b/arch/powerpc/cpu/mpc83xx/Kconfig
@@ -68,6 +68,9 @@
 config TARGET_TQM834X
 	bool "Support TQM834x"
 
+config TARGET_HRCON
+	bool "Support hrcon"
+
 endchoice
 
 source "board/esd/vme8349/Kconfig"
@@ -88,5 +91,6 @@
 source "board/sbc8349/Kconfig"
 source "board/tqc/tqm834x/Kconfig"
 source "board/ve8313/Kconfig"
+source "board/gdsys/mpc8308/Kconfig"
 
 endmenu
diff --git a/board/gdsys/405ep/iocon.c b/board/gdsys/405ep/iocon.c
index 1d7e141..3a51d86 100644
--- a/board/gdsys/405ep/iocon.c
+++ b/board/gdsys/405ep/iocon.c
@@ -17,6 +17,7 @@
 
 #include "../common/osd.h"
 #include "../common/mclink.h"
+#include "../common/phy.h"
 
 #include <i2c.h>
 #include <pca953x.h>
@@ -98,8 +99,6 @@
 unsigned int mclink_fpgacount;
 struct ihs_fpga *fpga_ptr[] = CONFIG_SYS_FPGA_PTR;
 
-static int setup_88e1518(const char *bus, unsigned char addr);
-
 int fpga_set_reg(u32 fpga, u16 *reg, off_t regoff, u16 data)
 {
 	int res;
@@ -647,190 +646,3 @@
 
 int bb_miiphy_buses_num = sizeof(bb_miiphy_buses) /
 			  sizeof(bb_miiphy_buses[0]);
-
-enum {
-	MIICMD_SET,
-	MIICMD_MODIFY,
-	MIICMD_VERIFY_VALUE,
-	MIICMD_WAIT_FOR_VALUE,
-};
-
-struct mii_setupcmd {
-	u8 token;
-	u8 reg;
-	u16 data;
-	u16 mask;
-	u32 timeout;
-};
-
-/*
- * verify we are talking to a 88e1518
- */
-struct mii_setupcmd verify_88e1518[] = {
-	{ MIICMD_SET, 22, 0x0000 },
-	{ MIICMD_VERIFY_VALUE, 2, 0x0141, 0xffff },
-	{ MIICMD_VERIFY_VALUE, 3, 0x0dd0, 0xfff0 },
-};
-
-/*
- * workaround for erratum mentioned in 88E1518 release notes
- */
-struct mii_setupcmd fixup_88e1518[] = {
-	{ MIICMD_SET, 22, 0x00ff },
-	{ MIICMD_SET, 17, 0x214b },
-	{ MIICMD_SET, 16, 0x2144 },
-	{ MIICMD_SET, 17, 0x0c28 },
-	{ MIICMD_SET, 16, 0x2146 },
-	{ MIICMD_SET, 17, 0xb233 },
-	{ MIICMD_SET, 16, 0x214d },
-	{ MIICMD_SET, 17, 0xcc0c },
-	{ MIICMD_SET, 16, 0x2159 },
-	{ MIICMD_SET, 22, 0x00fb },
-	{ MIICMD_SET,  7, 0xc00d },
-	{ MIICMD_SET, 22, 0x0000 },
-};
-
-/*
- * default initialization:
- * - set RGMII receive timing to "receive clock transition when data stable"
- * - set RGMII transmit timing to "transmit clock internally delayed"
- * - set RGMII output impedance target to 78,8 Ohm
- * - run output impedance calibration
- * - set autonegotiation advertise to 1000FD only
- */
-struct mii_setupcmd default_88e1518[] = {
-	{ MIICMD_SET, 22, 0x0002 },
-	{ MIICMD_MODIFY, 21, 0x0030, 0x0030 },
-	{ MIICMD_MODIFY, 25, 0x0000, 0x0003 },
-	{ MIICMD_MODIFY, 24, 0x8000, 0x8000 },
-	{ MIICMD_WAIT_FOR_VALUE, 24, 0x4000, 0x4000, 2000 },
-	{ MIICMD_SET, 22, 0x0000 },
-	{ MIICMD_MODIFY, 4, 0x0000, 0x01e0 },
-	{ MIICMD_MODIFY, 9, 0x0200, 0x0300 },
-};
-
-/*
- * turn off CLK125 for PHY daughterboard
- */
-struct mii_setupcmd ch1fix_88e1518[] = {
-	{ MIICMD_SET, 22, 0x0002 },
-	{ MIICMD_MODIFY, 16, 0x0006, 0x0006 },
-	{ MIICMD_SET, 22, 0x0000 },
-};
-
-/*
- * perform copper software reset
- */
-struct mii_setupcmd swreset_88e1518[] = {
-	{ MIICMD_SET, 22, 0x0000 },
-	{ MIICMD_MODIFY, 0, 0x8000, 0x8000 },
-	{ MIICMD_WAIT_FOR_VALUE, 0, 0x0000, 0x8000, 2000 },
-};
-
-static int process_setupcmd(const char *bus, unsigned char addr,
-			    struct mii_setupcmd *setupcmd)
-{
-	int res;
-	u8 reg = setupcmd->reg;
-	u16 data = setupcmd->data;
-	u16 mask = setupcmd->mask;
-	u32 timeout = setupcmd->timeout;
-	u16 orig_data;
-	unsigned long start;
-
-	debug("mii %s:%u reg %2u ", bus, addr, reg);
-
-	switch (setupcmd->token) {
-	case MIICMD_MODIFY:
-		res = miiphy_read(bus, addr, reg, &orig_data);
-		if (res)
-			break;
-		debug("is %04x. (value %04x mask %04x) ", orig_data, data,
-		      mask);
-		data = (orig_data & ~mask) | (data & mask);
-	case MIICMD_SET:
-		debug("=> %04x\n", data);
-		res = miiphy_write(bus, addr, reg, data);
-		break;
-	case MIICMD_VERIFY_VALUE:
-		res = miiphy_read(bus, addr, reg, &orig_data);
-		if (res)
-			break;
-		if ((orig_data & mask) != (data & mask))
-			res = -1;
-		debug("(value %04x mask %04x) == %04x? %s\n", data, mask,
-		      orig_data, res ? "FAIL" : "PASS");
-		break;
-	case MIICMD_WAIT_FOR_VALUE:
-		res = -1;
-		start = get_timer(0);
-		while ((res != 0) && (get_timer(start) < timeout)) {
-			res = miiphy_read(bus, addr, reg, &orig_data);
-			if (res)
-				continue;
-			if ((orig_data & mask) != (data & mask))
-				res = -1;
-		}
-		debug("(value %04x mask %04x) == %04x? %s after %lu ms\n", data,
-		      mask, orig_data, res ? "FAIL" : "PASS",
-		      get_timer(start));
-		break;
-	default:
-		res = -1;
-		break;
-	}
-
-	return res;
-}
-
-static int process_setup(const char *bus, unsigned char addr,
-			    struct mii_setupcmd *setupcmd, unsigned int count)
-{
-	int res = 0;
-	unsigned int k;
-
-	for (k = 0; k < count; ++k) {
-		res = process_setupcmd(bus, addr, &setupcmd[k]);
-		if (res) {
-			printf("mii cmd %u on bus %s addr %u failed, aborting setup",
-			       setupcmd[k].token, bus, addr);
-			break;
-		}
-	}
-
-	return res;
-}
-
-static int setup_88e1518(const char *bus, unsigned char addr)
-{
-	int res;
-
-	res = process_setup(bus, addr,
-			    verify_88e1518, ARRAY_SIZE(verify_88e1518));
-	if (res)
-		return res;
-
-	res = process_setup(bus, addr,
-			    fixup_88e1518, ARRAY_SIZE(fixup_88e1518));
-	if (res)
-		return res;
-
-	res = process_setup(bus, addr,
-			    default_88e1518, ARRAY_SIZE(default_88e1518));
-	if (res)
-		return res;
-
-	if (addr) {
-		res = process_setup(bus, addr,
-				    ch1fix_88e1518, ARRAY_SIZE(ch1fix_88e1518));
-		if (res)
-			return res;
-	}
-
-	res = process_setup(bus, addr,
-			    swreset_88e1518, ARRAY_SIZE(swreset_88e1518));
-	if (res)
-		return res;
-
-	return 0;
-}
diff --git a/board/gdsys/common/Makefile b/board/gdsys/common/Makefile
index 7f8b427..4957943 100644
--- a/board/gdsys/common/Makefile
+++ b/board/gdsys/common/Makefile
@@ -6,8 +6,10 @@
 #
 
 obj-$(CONFIG_SYS_FPGA_COMMON) += fpga.o
+obj-$(CONFIG_CMD_IOLOOP) += cmd_ioloop.o
 obj-$(CONFIG_IO) += miiphybb.o
 obj-$(CONFIG_IO64) += miiphybb.o
-obj-$(CONFIG_IOCON) += osd.o mclink.o dp501.o
+obj-$(CONFIG_IOCON) += osd.o mclink.o dp501.o phy.o
 obj-$(CONFIG_DLVISION_10G) += osd.o
 obj-$(CONFIG_CONTROLCENTERD) += dp501.o
+obj-$(CONFIG_HRCON) += osd.o mclink.o dp501.o phy.o
diff --git a/board/gdsys/common/cmd_ioloop.c b/board/gdsys/common/cmd_ioloop.c
new file mode 100644
index 0000000..e0c74fe
--- /dev/null
+++ b/board/gdsys/common/cmd_ioloop.c
@@ -0,0 +1,295 @@
+/*
+ * (C) Copyright 2014
+ * Dirk Eibach, Guntermann & Drunck GmbH, dirk.eibach@gdsys.cc
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <command.h>
+
+#include <gdsys_fpga.h>
+
+enum {
+	STATE_TX_PACKET_BUILDING = 1<<0,
+	STATE_TX_TRANSMITTING = 1<<1,
+	STATE_TX_BUFFER_FULL = 1<<2,
+	STATE_TX_ERR = 1<<3,
+	STATE_RECEIVE_TIMEOUT = 1<<4,
+	STATE_PROC_RX_STORE_TIMEOUT = 1<<5,
+	STATE_PROC_RX_RECEIVE_TIMEOUT = 1<<6,
+	STATE_RX_DIST_ERR = 1<<7,
+	STATE_RX_LENGTH_ERR = 1<<8,
+	STATE_RX_FRAME_CTR_ERR = 1<<9,
+	STATE_RX_FCS_ERR = 1<<10,
+	STATE_RX_PACKET_DROPPED = 1<<11,
+	STATE_RX_DATA_LAST = 1<<12,
+	STATE_RX_DATA_FIRST = 1<<13,
+	STATE_RX_DATA_AVAILABLE = 1<<15,
+};
+
+enum {
+	CTRL_PROC_RECEIVE_ENABLE = 1<<12,
+	CTRL_FLUSH_TRANSMIT_BUFFER = 1<<15,
+};
+
+enum {
+	IRQ_CPU_TRANSMITBUFFER_FREE_STATUS = 1<<5,
+	IRQ_CPU_PACKET_TRANSMITTED_EVENT = 1<<6,
+	IRQ_NEW_CPU_PACKET_RECEIVED_EVENT = 1<<7,
+	IRQ_CPU_RECEIVE_DATA_AVAILABLE_STATUS = 1<<8,
+};
+
+struct io_generic_packet {
+	u16 target_address;
+	u16 source_address;
+	u8 packet_type;
+	u8 bc;
+	u16 packet_length;
+} __attribute__((__packed__));
+
+unsigned long long rx_ctr;
+unsigned long long tx_ctr;
+unsigned long long err_ctr;
+
+static void io_check_status(unsigned int fpga, u16 status, bool silent)
+{
+	u16 mask = STATE_RX_DIST_ERR | STATE_RX_LENGTH_ERR |
+		   STATE_RX_FRAME_CTR_ERR | STATE_RX_FCS_ERR |
+		   STATE_RX_PACKET_DROPPED | STATE_TX_ERR;
+
+	if (!(status & mask)) {
+		FPGA_SET_REG(fpga, ep.rx_tx_status, status);
+		return;
+	}
+
+	err_ctr++;
+	FPGA_SET_REG(fpga, ep.rx_tx_status, status);
+
+	if (silent)
+		return;
+
+	if (status & STATE_RX_PACKET_DROPPED)
+		printf("RX_PACKET_DROPPED, status %04x\n", status);
+
+	if (status & STATE_RX_DIST_ERR)
+		printf("RX_DIST_ERR\n");
+	if (status & STATE_RX_LENGTH_ERR)
+		printf("RX_LENGTH_ERR\n");
+	if (status & STATE_RX_FRAME_CTR_ERR)
+		printf("RX_FRAME_CTR_ERR\n");
+	if (status & STATE_RX_FCS_ERR)
+		printf("RX_FCS_ERR\n");
+
+	if (status & STATE_TX_ERR)
+		printf("TX_ERR\n");
+}
+
+static void io_send(unsigned int fpga, unsigned int size)
+{
+	unsigned int k;
+	struct io_generic_packet packet = {
+		.source_address = 1,
+		.packet_type = 1,
+		.packet_length = size,
+	};
+	u16 *p = (u16 *)&packet;
+
+	for (k = 0; k < sizeof(packet) / 2; ++k)
+		FPGA_SET_REG(fpga, ep.transmit_data, *p++);
+
+	for (k = 0; k < (size + 1) / 2; ++k)
+		FPGA_SET_REG(fpga, ep.transmit_data, k);
+
+	FPGA_SET_REG(fpga, ep.rx_tx_control,
+		     CTRL_PROC_RECEIVE_ENABLE | CTRL_FLUSH_TRANSMIT_BUFFER);
+
+	tx_ctr++;
+}
+
+static void io_receive(unsigned int fpga)
+{
+	unsigned int k = 0;
+	u16 rx_tx_status;
+
+	FPGA_GET_REG(fpga, ep.rx_tx_status, &rx_tx_status);
+
+	while (rx_tx_status & STATE_RX_DATA_AVAILABLE) {
+		u16 rx;
+
+		if (rx_tx_status & STATE_RX_DATA_LAST)
+			rx_ctr++;
+
+		FPGA_GET_REG(fpga, ep.receive_data, &rx);
+
+		FPGA_GET_REG(fpga, ep.rx_tx_status, &rx_tx_status);
+
+		++k;
+	}
+}
+
+static void io_reflect(unsigned int fpga)
+{
+	u16 buffer[128];
+
+	unsigned int k = 0;
+	unsigned int n;
+	u16 rx_tx_status;
+
+	FPGA_GET_REG(fpga, ep.rx_tx_status, &rx_tx_status);
+
+	while (rx_tx_status & STATE_RX_DATA_AVAILABLE) {
+		FPGA_GET_REG(fpga, ep.receive_data, &buffer[k++]);
+		if (rx_tx_status & STATE_RX_DATA_LAST)
+			break;
+
+		FPGA_GET_REG(fpga, ep.rx_tx_status, &rx_tx_status);
+	}
+
+	if (!k)
+		return;
+
+	for (n = 0; n < k; ++n)
+		FPGA_SET_REG(fpga, ep.transmit_data, buffer[n]);
+
+	FPGA_SET_REG(fpga, ep.rx_tx_control,
+		     CTRL_PROC_RECEIVE_ENABLE | CTRL_FLUSH_TRANSMIT_BUFFER);
+
+	tx_ctr++;
+}
+
+/*
+ * FPGA io-endpoint reflector
+ *
+ * Syntax:
+ *	ioreflect {fpga} {reportrate}
+ */
+int do_ioreflect(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
+{
+	unsigned int fpga;
+	unsigned int rate = 0;
+	unsigned long long last_seen = 0;
+
+	if (argc < 2)
+		return CMD_RET_USAGE;
+
+	fpga = simple_strtoul(argv[1], NULL, 10);
+
+	/*
+	 * If another parameter, it is the report rate in packets.
+	 */
+	if (argc > 2)
+		rate = simple_strtoul(argv[2], NULL, 10);
+
+	/* enable receive path */
+	FPGA_SET_REG(fpga, ep.rx_tx_control, CTRL_PROC_RECEIVE_ENABLE);
+
+	/* set device address to dummy 1*/
+	FPGA_SET_REG(fpga, ep.device_address, 1);
+
+	rx_ctr = 0; tx_ctr = 0; err_ctr = 0;
+
+	while (1) {
+		u16 top_int;
+		u16 rx_tx_status;
+
+		FPGA_GET_REG(fpga, top_interrupt, &top_int);
+		FPGA_GET_REG(fpga, ep.rx_tx_status, &rx_tx_status);
+
+		io_check_status(fpga, rx_tx_status, true);
+		if ((top_int & IRQ_CPU_RECEIVE_DATA_AVAILABLE_STATUS) &&
+		    (top_int & IRQ_CPU_TRANSMITBUFFER_FREE_STATUS))
+			io_reflect(fpga);
+
+		if (rate) {
+			if (!(tx_ctr % rate) && (tx_ctr != last_seen))
+				printf("refl %llu, err %llu\n", tx_ctr,
+				       err_ctr);
+			last_seen = tx_ctr;
+		}
+
+		if (ctrlc())
+			break;
+	}
+
+	return 0;
+}
+
+/*
+ * FPGA io-endpoint looptest
+ *
+ * Syntax:
+ *	ioloop {fpga} {size} {rate}
+ */
+#define DISP_LINE_LEN	16
+int do_ioloop(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
+{
+	unsigned int fpga;
+	unsigned int size;
+	unsigned int rate = 0;
+
+	if (argc < 3)
+		return CMD_RET_USAGE;
+
+	/*
+	 * FPGA is specified since argc > 2
+	 */
+	fpga = simple_strtoul(argv[1], NULL, 10);
+
+	/*
+	 * packet size is specified since argc > 2
+	 */
+	size = simple_strtoul(argv[2], NULL, 10);
+
+	/*
+	 * If another parameter, it is the test rate in packets per second.
+	 */
+	if (argc > 3)
+		rate = simple_strtoul(argv[3], NULL, 10);
+
+	/* enable receive path */
+	FPGA_SET_REG(fpga, ep.rx_tx_control, CTRL_PROC_RECEIVE_ENABLE);
+
+	/* set device address to dummy 1*/
+	FPGA_SET_REG(fpga, ep.device_address, 1);
+
+	rx_ctr = 0; tx_ctr = 0; err_ctr = 0;
+
+	while (1) {
+		u16 top_int;
+		u16 rx_tx_status;
+
+		FPGA_GET_REG(fpga, top_interrupt, &top_int);
+		FPGA_GET_REG(fpga, ep.rx_tx_status, &rx_tx_status);
+
+		io_check_status(fpga, rx_tx_status, false);
+		if (top_int & IRQ_CPU_TRANSMITBUFFER_FREE_STATUS)
+			io_send(fpga, size);
+		if (top_int & IRQ_CPU_RECEIVE_DATA_AVAILABLE_STATUS)
+			io_receive(fpga);
+
+		if (rate) {
+			if (ctrlc())
+				break;
+			udelay(1000000 / rate);
+			if (!(tx_ctr % rate))
+				printf("d %lld, tx %llu, rx %llu, err %llu\n",
+				       tx_ctr - rx_ctr, tx_ctr, rx_ctr,
+				       err_ctr);
+		}
+	}
+
+	return 0;
+}
+
+U_BOOT_CMD(
+	ioloop,	4,	0,	do_ioloop,
+	"fpga io-endpoint looptest",
+	"fpga packetsize [packets/sec]"
+);
+
+U_BOOT_CMD(
+	ioreflect, 3,	0,	do_ioreflect,
+	"fpga io-endpoint reflector",
+	"fpga reportrate"
+);
diff --git a/board/gdsys/common/ihs_mdio.c b/board/gdsys/common/ihs_mdio.c
new file mode 100644
index 0000000..1d6eb7b
--- /dev/null
+++ b/board/gdsys/common/ihs_mdio.c
@@ -0,0 +1,88 @@
+/*
+ * (C) Copyright 2014
+ * Dirk Eibach,  Guntermann & Drunck GmbH, eibach@gdsys.de
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+
+#include <gdsys_fpga.h>
+#include <miiphy.h>
+
+#include "ihs_mdio.h"
+
+static int ihs_mdio_idle(struct mii_dev *bus)
+{
+	struct ihs_mdio_info *info = bus->priv;
+	u16 val;
+	unsigned int ctr = 0;
+
+	do {
+		FPGA_GET_REG(info->fpga, mdio.control, &val);
+		udelay(100);
+		if (ctr++ > 10)
+			return -1;
+	} while (!(val & (1 << 12)));
+
+	return 0;
+}
+
+static int ihs_mdio_reset(struct mii_dev *bus)
+{
+	ihs_mdio_idle(bus);
+
+	return 0;
+}
+
+static int ihs_mdio_read(struct mii_dev *bus, int addr, int dev_addr,
+			 int regnum)
+{
+	struct ihs_mdio_info *info = bus->priv;
+	u16 val;
+
+	ihs_mdio_idle(bus);
+
+	FPGA_SET_REG(info->fpga, mdio.control,
+		     ((addr & 0x1f) << 5) | (regnum & 0x1f) | (2 << 10));
+
+	/* wait for rx data available */
+	udelay(100);
+
+	FPGA_GET_REG(info->fpga, mdio.rx_data, &val);
+
+	return val;
+}
+
+static int ihs_mdio_write(struct mii_dev *bus, int addr, int dev_addr,
+			  int regnum, u16 value)
+{
+	struct ihs_mdio_info *info = bus->priv;
+
+	ihs_mdio_idle(bus);
+
+	FPGA_SET_REG(info->fpga, mdio.address_data, value);
+	FPGA_SET_REG(info->fpga, mdio.control,
+		     ((addr & 0x1f) << 5) | (regnum & 0x1f) | (1 << 10));
+
+	return 0;
+}
+
+int ihs_mdio_init(struct ihs_mdio_info *info)
+{
+	struct mii_dev *bus = mdio_alloc();
+
+	if (!bus) {
+		printf("Failed to allocate FSL MDIO bus\n");
+		return -1;
+	}
+
+	bus->read = ihs_mdio_read;
+	bus->write = ihs_mdio_write;
+	bus->reset = ihs_mdio_reset;
+	sprintf(bus->name, info->name);
+
+	bus->priv = info;
+
+	return mdio_register(bus);
+}
diff --git a/board/gdsys/common/ihs_mdio.h b/board/gdsys/common/ihs_mdio.h
new file mode 100644
index 0000000..64b4049
--- /dev/null
+++ b/board/gdsys/common/ihs_mdio.h
@@ -0,0 +1,18 @@
+/*
+ * (C) Copyright 2014
+ * Dirk Eibach,  Guntermann & Drunck GmbH, dirk.eibach@gdsys.cc
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef _IHS_MDIO_H_
+#define _IHS_MDIO_H_
+
+struct ihs_mdio_info {
+	u32 fpga;
+	char *name;
+};
+
+int ihs_mdio_init(struct ihs_mdio_info *info);
+
+#endif
diff --git a/board/gdsys/common/phy.c b/board/gdsys/common/phy.c
new file mode 100644
index 0000000..fb92658
--- /dev/null
+++ b/board/gdsys/common/phy.c
@@ -0,0 +1,280 @@
+/*
+ * (C) Copyright 2014
+ * Dirk Eibach,  Guntermann & Drunck GmbH, eibach@gdsys.de
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+
+#include <miiphy.h>
+
+enum {
+	MIICMD_SET,
+	MIICMD_MODIFY,
+	MIICMD_VERIFY_VALUE,
+	MIICMD_WAIT_FOR_VALUE,
+};
+
+struct mii_setupcmd {
+	u8 token;
+	u8 reg;
+	u16 data;
+	u16 mask;
+	u32 timeout;
+};
+
+/*
+ * verify we are talking to a 88e1518
+ */
+struct mii_setupcmd verify_88e1518[] = {
+	{ MIICMD_SET, 22, 0x0000 },
+	{ MIICMD_VERIFY_VALUE, 2, 0x0141, 0xffff },
+	{ MIICMD_VERIFY_VALUE, 3, 0x0dd0, 0xfff0 },
+};
+
+/*
+ * workaround for erratum mentioned in 88E1518 release notes
+ */
+struct mii_setupcmd fixup_88e1518[] = {
+	{ MIICMD_SET, 22, 0x00ff },
+	{ MIICMD_SET, 17, 0x214b },
+	{ MIICMD_SET, 16, 0x2144 },
+	{ MIICMD_SET, 17, 0x0c28 },
+	{ MIICMD_SET, 16, 0x2146 },
+	{ MIICMD_SET, 17, 0xb233 },
+	{ MIICMD_SET, 16, 0x214d },
+	{ MIICMD_SET, 17, 0xcc0c },
+	{ MIICMD_SET, 16, 0x2159 },
+	{ MIICMD_SET, 22, 0x00fb },
+	{ MIICMD_SET,  7, 0xc00d },
+	{ MIICMD_SET, 22, 0x0000 },
+};
+
+/*
+ * default initialization:
+ * - set RGMII receive timing to "receive clock transition when data stable"
+ * - set RGMII transmit timing to "transmit clock internally delayed"
+ * - set RGMII output impedance target to 78,8 Ohm
+ * - run output impedance calibration
+ * - set autonegotiation advertise to 1000FD only
+ */
+struct mii_setupcmd default_88e1518[] = {
+	{ MIICMD_SET, 22, 0x0002 },
+	{ MIICMD_MODIFY, 21, 0x0030, 0x0030 },
+	{ MIICMD_MODIFY, 25, 0x0000, 0x0003 },
+	{ MIICMD_MODIFY, 24, 0x8000, 0x8000 },
+	{ MIICMD_WAIT_FOR_VALUE, 24, 0x4000, 0x4000, 2000 },
+	{ MIICMD_SET, 22, 0x0000 },
+	{ MIICMD_MODIFY, 4, 0x0000, 0x01e0 },
+	{ MIICMD_MODIFY, 9, 0x0200, 0x0300 },
+};
+
+/*
+ * turn off CLK125 for PHY daughterboard
+ */
+struct mii_setupcmd ch1fix_88e1518[] = {
+	{ MIICMD_SET, 22, 0x0002 },
+	{ MIICMD_MODIFY, 16, 0x0006, 0x0006 },
+	{ MIICMD_SET, 22, 0x0000 },
+};
+
+/*
+ * perform copper software reset
+ */
+struct mii_setupcmd swreset_88e1518[] = {
+	{ MIICMD_SET, 22, 0x0000 },
+	{ MIICMD_MODIFY, 0, 0x8000, 0x8000 },
+	{ MIICMD_WAIT_FOR_VALUE, 0, 0x0000, 0x8000, 2000 },
+};
+
+/*
+ * special one for 88E1514:
+ * Force SGMII to Copper mode
+ */
+struct mii_setupcmd mii_to_copper_88e1514[] = {
+	{ MIICMD_SET, 22, 0x0012 },
+	{ MIICMD_MODIFY, 20, 0x0001, 0x0007 },
+	{ MIICMD_MODIFY, 20, 0x8000, 0x8000 },
+	{ MIICMD_SET, 22, 0x0000 },
+};
+
+/*
+ * turn off SGMII auto-negotiation
+ */
+struct mii_setupcmd sgmii_autoneg_off_88e1518[] = {
+	{ MIICMD_SET, 22, 0x0001 },
+	{ MIICMD_MODIFY, 0, 0x0000, 0x1000 },
+	{ MIICMD_MODIFY, 0, 0x8000, 0x8000 },
+	{ MIICMD_SET, 22, 0x0000 },
+};
+
+/*
+ * invert LED2 polarity
+ */
+struct mii_setupcmd invert_led2_88e1514[] = {
+	{ MIICMD_SET, 22, 0x0003 },
+	{ MIICMD_MODIFY, 17, 0x0030, 0x0010 },
+	{ MIICMD_SET, 22, 0x0000 },
+};
+
+static int process_setupcmd(const char *bus, unsigned char addr,
+			    struct mii_setupcmd *setupcmd)
+{
+	int res;
+	u8 reg = setupcmd->reg;
+	u16 data = setupcmd->data;
+	u16 mask = setupcmd->mask;
+	u32 timeout = setupcmd->timeout;
+	u16 orig_data;
+	unsigned long start;
+
+	debug("mii %s:%u reg %2u ", bus, addr, reg);
+
+	switch (setupcmd->token) {
+	case MIICMD_MODIFY:
+		res = miiphy_read(bus, addr, reg, &orig_data);
+		if (res)
+			break;
+		debug("is %04x. (value %04x mask %04x) ", orig_data, data,
+		      mask);
+		data = (orig_data & ~mask) | (data & mask);
+		/* fallthrough */
+	case MIICMD_SET:
+		debug("=> %04x\n", data);
+		res = miiphy_write(bus, addr, reg, data);
+		break;
+	case MIICMD_VERIFY_VALUE:
+		res = miiphy_read(bus, addr, reg, &orig_data);
+		if (res)
+			break;
+		if ((orig_data & mask) != (data & mask))
+			res = -1;
+		debug("(value %04x mask %04x) == %04x? %s\n", data, mask,
+		      orig_data, res ? "FAIL" : "PASS");
+		break;
+	case MIICMD_WAIT_FOR_VALUE:
+		res = -1;
+		start = get_timer(0);
+		while ((res != 0) && (get_timer(start) < timeout)) {
+			res = miiphy_read(bus, addr, reg, &orig_data);
+			if (res)
+				continue;
+			if ((orig_data & mask) != (data & mask))
+				res = -1;
+		}
+		debug("(value %04x mask %04x) == %04x? %s after %lu ms\n", data,
+		      mask, orig_data, res ? "FAIL" : "PASS",
+		      get_timer(start));
+		break;
+	default:
+		res = -1;
+		break;
+	}
+
+	return res;
+}
+
+static int process_setup(const char *bus, unsigned char addr,
+			    struct mii_setupcmd *setupcmd, unsigned int count)
+{
+	int res = 0;
+	unsigned int k;
+
+	for (k = 0; k < count; ++k) {
+		res = process_setupcmd(bus, addr, &setupcmd[k]);
+		if (res) {
+			printf("mii cmd %u on bus %s addr %u failed, aborting setup\n",
+			       setupcmd[k].token, bus, addr);
+			break;
+		}
+	}
+
+	return res;
+}
+
+int setup_88e1518(const char *bus, unsigned char addr)
+{
+	int res;
+
+	res = process_setup(bus, addr,
+			    verify_88e1518, ARRAY_SIZE(verify_88e1518));
+	if (res)
+		return res;
+
+	res = process_setup(bus, addr,
+			    fixup_88e1518, ARRAY_SIZE(fixup_88e1518));
+	if (res)
+		return res;
+
+	res = process_setup(bus, addr,
+			    default_88e1518, ARRAY_SIZE(default_88e1518));
+	if (res)
+		return res;
+
+	if (addr) {
+		res = process_setup(bus, addr,
+				    ch1fix_88e1518, ARRAY_SIZE(ch1fix_88e1518));
+		if (res)
+			return res;
+	}
+
+	res = process_setup(bus, addr,
+			    swreset_88e1518, ARRAY_SIZE(swreset_88e1518));
+	if (res)
+		return res;
+
+	return 0;
+}
+
+int setup_88e1514(const char *bus, unsigned char addr)
+{
+	int res;
+
+	res = process_setup(bus, addr,
+			    verify_88e1518, ARRAY_SIZE(verify_88e1518));
+	if (res)
+		return res;
+
+	res = process_setup(bus, addr,
+			    fixup_88e1518, ARRAY_SIZE(fixup_88e1518));
+	if (res)
+		return res;
+
+	res = process_setup(bus, addr,
+			    mii_to_copper_88e1514,
+			    ARRAY_SIZE(mii_to_copper_88e1514));
+	if (res)
+		return res;
+
+	res = process_setup(bus, addr,
+			    sgmii_autoneg_off_88e1518,
+			    ARRAY_SIZE(sgmii_autoneg_off_88e1518));
+	if (res)
+		return res;
+
+	res = process_setup(bus, addr,
+			    invert_led2_88e1514,
+			    ARRAY_SIZE(invert_led2_88e1514));
+	if (res)
+		return res;
+
+	res = process_setup(bus, addr,
+			    default_88e1518, ARRAY_SIZE(default_88e1518));
+	if (res)
+		return res;
+
+	if (addr) {
+		res = process_setup(bus, addr,
+				    ch1fix_88e1518, ARRAY_SIZE(ch1fix_88e1518));
+		if (res)
+			return res;
+	}
+
+	res = process_setup(bus, addr,
+			    swreset_88e1518, ARRAY_SIZE(swreset_88e1518));
+	if (res)
+		return res;
+
+	return 0;
+}
diff --git a/board/gdsys/common/phy.h b/board/gdsys/common/phy.h
new file mode 100644
index 0000000..afbdc65
--- /dev/null
+++ b/board/gdsys/common/phy.h
@@ -0,0 +1,14 @@
+/*
+ * (C) Copyright 2014
+ * Dirk Eibach,  Guntermann & Drunck GmbH, dirk.eibach@gdsys.cc
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef _PHY_H_
+#define _PHY_H_
+
+int setup_88e1514(const char *bus, unsigned char addr);
+int setup_88e1518(const char *bus, unsigned char addr);
+
+#endif
diff --git a/board/gdsys/mpc8308/Kconfig b/board/gdsys/mpc8308/Kconfig
new file mode 100644
index 0000000..43e1663
--- /dev/null
+++ b/board/gdsys/mpc8308/Kconfig
@@ -0,0 +1,12 @@
+if TARGET_HRCON
+
+config SYS_BOARD
+	default "mpc8308"
+
+config SYS_VENDOR
+	default "gdsys"
+
+config SYS_CONFIG_NAME
+	default "hrcon"
+
+endif
diff --git a/board/gdsys/mpc8308/MAINTAINERS b/board/gdsys/mpc8308/MAINTAINERS
new file mode 100644
index 0000000..a7853a5
--- /dev/null
+++ b/board/gdsys/mpc8308/MAINTAINERS
@@ -0,0 +1,6 @@
+MPC8308 BOARD
+M:	Dirk Eibach <eibach@gdsys.de>
+S:	Maintained
+F:	board/gdsys/mpc8308/
+F:	include/configs/hrcon.h
+F:	configs/hrcon_defconfig
diff --git a/board/gdsys/mpc8308/Makefile b/board/gdsys/mpc8308/Makefile
new file mode 100644
index 0000000..b5dfdbb
--- /dev/null
+++ b/board/gdsys/mpc8308/Makefile
@@ -0,0 +1,9 @@
+#
+# (C) Copyright 2014
+# Dirk Eibach,  Guntermann & Drunck GmbH, eibach@gdsys.de
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+obj-y := mpc8308.o sdram.o
+obj-$(CONFIG_HRCON) += hrcon.o
diff --git a/board/gdsys/mpc8308/hrcon.c b/board/gdsys/mpc8308/hrcon.c
new file mode 100644
index 0000000..a051682
--- /dev/null
+++ b/board/gdsys/mpc8308/hrcon.c
@@ -0,0 +1,675 @@
+/*
+ * (C) Copyright 2014
+ * Dirk Eibach,  Guntermann & Drunck GmbH, eibach@gdsys.de
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <hwconfig.h>
+#include <i2c.h>
+#include <spi.h>
+#include <libfdt.h>
+#include <fdt_support.h>
+#include <pci.h>
+#include <mpc83xx.h>
+#include <fsl_esdhc.h>
+#include <asm/io.h>
+#include <asm/fsl_serdes.h>
+#include <asm/fsl_mpc83xx_serdes.h>
+
+#include "mpc8308.h"
+
+#include <gdsys_fpga.h>
+
+#include "../common/osd.h"
+#include "../common/mclink.h"
+#include "../common/phy.h"
+
+#include <pca953x.h>
+#include <pca9698.h>
+
+#include <miiphy.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define MAX_MUX_CHANNELS 2
+
+enum {
+	UNITTYPE_MAIN_SERVER = 0,
+	UNITTYPE_MAIN_USER = 1,
+	UNITTYPE_VIDEO_SERVER = 2,
+	UNITTYPE_VIDEO_USER = 3,
+};
+
+enum {
+	UNITTYPEPCB_DVI = 0,
+	UNITTYPEPCB_DP_165 = 1,
+	UNITTYPEPCB_DP_300 = 2,
+	UNITTYPEPCB_HDMI = 3,
+};
+
+enum {
+	HWVER_100 = 0,
+	HWVER_110 = 1,
+};
+
+enum {
+	FPGA_HWVER_200 = 0,
+	FPGA_HWVER_210 = 1,
+};
+
+enum {
+	COMPRESSION_NONE = 0,
+	COMPRESSION_TYPE1_DELTA = 1,
+	COMPRESSION_TYPE1_TYPE2_DELTA = 3,
+};
+
+enum {
+	AUDIO_NONE = 0,
+	AUDIO_TX = 1,
+	AUDIO_RX = 2,
+	AUDIO_RXTX = 3,
+};
+
+enum {
+	SYSCLK_147456 = 0,
+};
+
+enum {
+	RAM_DDR2_32 = 0,
+	RAM_DDR3_32 = 1,
+};
+
+enum {
+	CARRIER_SPEED_1G = 0,
+	CARRIER_SPEED_2_5G = 1,
+};
+
+enum {
+	MCFPGA_DONE = 1 << 0,
+	MCFPGA_INIT_N = 1 << 1,
+	MCFPGA_PROGRAM_N = 1 << 2,
+	MCFPGA_UPDATE_ENABLE_N = 1 << 3,
+	MCFPGA_RESET_N = 1 << 4,
+};
+
+enum {
+	GPIO_MDC = 1 << 14,
+	GPIO_MDIO = 1 << 15,
+};
+
+unsigned int mclink_fpgacount;
+struct ihs_fpga *fpga_ptr[] = CONFIG_SYS_FPGA_PTR;
+
+int fpga_set_reg(u32 fpga, u16 *reg, off_t regoff, u16 data)
+{
+	int res;
+
+	switch (fpga) {
+	case 0:
+		out_le16(reg, data);
+		break;
+	default:
+		res = mclink_send(fpga - 1, regoff, data);
+		if (res < 0) {
+			printf("mclink_send reg %02lx data %04x returned %d\n",
+			       regoff, data, res);
+			return res;
+		}
+		break;
+	}
+
+	return 0;
+}
+
+int fpga_get_reg(u32 fpga, u16 *reg, off_t regoff, u16 *data)
+{
+	int res;
+
+	switch (fpga) {
+	case 0:
+		*data = in_le16(reg);
+		break;
+	default:
+		if (fpga > mclink_fpgacount)
+			return -EINVAL;
+		res = mclink_receive(fpga - 1, regoff, data);
+		if (res < 0) {
+			printf("mclink_receive reg %02lx returned %d\n",
+			       regoff, res);
+			return res;
+		}
+	}
+
+	return 0;
+}
+
+int checkboard(void)
+{
+	char *s = getenv("serial#");
+	bool hw_type_cat = pca9698_get_value(0x20, 20);
+
+	puts("Board: ");
+
+	printf("HRCon %s", hw_type_cat ? "CAT" : "Fiber");
+
+	if (s != NULL) {
+		puts(", serial# ");
+		puts(s);
+	}
+
+	puts("\n");
+
+	return 0;
+}
+
+static void print_fpga_info(unsigned int fpga, bool rgmii2_present)
+{
+	u16 versions;
+	u16 fpga_version;
+	u16 fpga_features;
+	unsigned unit_type;
+	unsigned unit_type_pcb_video;
+	unsigned hardware_version;
+	unsigned feature_compression;
+	unsigned feature_osd;
+	unsigned feature_audio;
+	unsigned feature_sysclock;
+	unsigned feature_ramconfig;
+	unsigned feature_carrier_speed;
+	unsigned feature_carriers;
+	unsigned feature_video_channels;
+
+	FPGA_GET_REG(fpga, versions, &versions);
+	FPGA_GET_REG(fpga, fpga_version, &fpga_version);
+	FPGA_GET_REG(fpga, fpga_features, &fpga_features);
+
+	unit_type = (versions & 0xf000) >> 12;
+	unit_type_pcb_video = (versions & 0x01c0) >> 6;
+	feature_compression = (fpga_features & 0xe000) >> 13;
+	feature_osd = fpga_features & (1<<11);
+	feature_audio = (fpga_features & 0x0600) >> 9;
+	feature_sysclock = (fpga_features & 0x0180) >> 7;
+	feature_ramconfig = (fpga_features & 0x0060) >> 5;
+	feature_carrier_speed = fpga_features & (1<<4);
+	feature_carriers = (fpga_features & 0x000c) >> 2;
+	feature_video_channels = fpga_features & 0x0003;
+
+	switch (unit_type) {
+	case UNITTYPE_MAIN_USER:
+		printf("Mainchannel");
+		break;
+
+	case UNITTYPE_VIDEO_USER:
+		printf("Videochannel");
+		break;
+
+	default:
+		printf("UnitType %d(not supported)", unit_type);
+		break;
+	}
+
+	if (unit_type == UNITTYPE_MAIN_USER) {
+		hardware_version =
+			  (!!pca9698_get_value(0x20, 24) << 0)
+			| (!!pca9698_get_value(0x20, 25) << 1)
+			| (!!pca9698_get_value(0x20, 26) << 2)
+			| (!!pca9698_get_value(0x20, 27) << 3)
+			| (!!pca9698_get_value(0x20, 28) << 4);
+		switch (hardware_version) {
+		case HWVER_100:
+			printf(" HW-Ver 1.00,");
+			break;
+
+		case HWVER_110:
+			printf(" HW-Ver 1.10,");
+			break;
+
+		default:
+			printf(" HW-Ver %d(not supported),",
+			       hardware_version);
+			break;
+		}
+		if (rgmii2_present)
+			printf(" RGMII2,");
+	}
+
+	if (unit_type == UNITTYPE_VIDEO_USER) {
+		hardware_version = versions & 0x000f;
+		switch (hardware_version) {
+		case FPGA_HWVER_200:
+			printf(" HW-Ver 2.00,");
+			break;
+
+		case FPGA_HWVER_210:
+			printf(" HW-Ver 2.10,");
+			break;
+
+		default:
+			printf(" HW-Ver %d(not supported),",
+			       hardware_version);
+			break;
+		}
+	}
+
+	switch (unit_type_pcb_video) {
+	case UNITTYPEPCB_DVI:
+		printf(" DVI,");
+		break;
+
+	case UNITTYPEPCB_DP_165:
+		printf(" DP 165MPix/s,");
+		break;
+
+	case UNITTYPEPCB_DP_300:
+		printf(" DP 300MPix/s,");
+		break;
+
+	case UNITTYPEPCB_HDMI:
+		printf(" HDMI,");
+		break;
+	}
+
+	printf(" FPGA V %d.%02d\n       features:",
+	       fpga_version / 100, fpga_version % 100);
+
+
+	switch (feature_compression) {
+	case COMPRESSION_NONE:
+		printf(" no compression");
+		break;
+
+	case COMPRESSION_TYPE1_DELTA:
+		printf(" type1-deltacompression");
+		break;
+
+	case COMPRESSION_TYPE1_TYPE2_DELTA:
+		printf(" type1-deltacompression, type2-inlinecompression");
+		break;
+
+	default:
+		printf(" compression %d(not supported)", feature_compression);
+		break;
+	}
+
+	printf(", %sosd", feature_osd ? "" : "no ");
+
+	switch (feature_audio) {
+	case AUDIO_NONE:
+		printf(", no audio");
+		break;
+
+	case AUDIO_TX:
+		printf(", audio tx");
+		break;
+
+	case AUDIO_RX:
+		printf(", audio rx");
+		break;
+
+	case AUDIO_RXTX:
+		printf(", audio rx+tx");
+		break;
+
+	default:
+		printf(", audio %d(not supported)", feature_audio);
+		break;
+	}
+
+	puts(",\n       ");
+
+	switch (feature_sysclock) {
+	case SYSCLK_147456:
+		printf("clock 147.456 MHz");
+		break;
+
+	default:
+		printf("clock %d(not supported)", feature_sysclock);
+		break;
+	}
+
+	switch (feature_ramconfig) {
+	case RAM_DDR2_32:
+		printf(", RAM 32 bit DDR2");
+		break;
+
+	case RAM_DDR3_32:
+		printf(", RAM 32 bit DDR3");
+		break;
+
+	default:
+		printf(", RAM %d(not supported)", feature_ramconfig);
+		break;
+	}
+
+	printf(", %d carrier(s) %s", feature_carriers,
+	       feature_carrier_speed ? "2.5Gbit/s" : "1Gbit/s");
+
+	printf(", %d video channel(s)\n", feature_video_channels);
+}
+
+int last_stage_init(void)
+{
+	int slaves;
+	unsigned int k;
+	unsigned int mux_ch;
+	unsigned char mclink_controllers[] = { 0x24, 0x25, 0x26 };
+	u16 fpga_features;
+	bool hw_type_cat = pca9698_get_value(0x20, 20);
+	bool ch0_rgmii2_present = false;
+
+	FPGA_GET_REG(0, fpga_features, &fpga_features);
+
+	/* Turn on Parade DP501 */
+	pca9698_direction_output(0x20, 10, 1);
+
+	ch0_rgmii2_present = !pca9698_get_value(0x20, 30);
+
+	/* wait for FPGA done */
+	for (k = 0; k < ARRAY_SIZE(mclink_controllers); ++k) {
+		unsigned int ctr = 0;
+
+		if (i2c_probe(mclink_controllers[k]))
+			continue;
+
+		while (!(pca953x_get_val(mclink_controllers[k])
+		       & MCFPGA_DONE)) {
+			udelay(100000);
+			if (ctr++ > 5) {
+				printf("no done for mclink_controller %d\n", k);
+				break;
+			}
+		}
+	}
+
+	if (hw_type_cat) {
+		miiphy_register(bb_miiphy_buses[0].name, bb_miiphy_read,
+				bb_miiphy_write);
+		for (mux_ch = 0; mux_ch < MAX_MUX_CHANNELS; ++mux_ch) {
+			if ((mux_ch == 1) && !ch0_rgmii2_present)
+				continue;
+
+			setup_88e1514(bb_miiphy_buses[0].name, mux_ch);
+		}
+	}
+
+	/* give slave-PLLs and Parade DP501 some time to be up and running */
+	udelay(500000);
+
+	mclink_fpgacount = CONFIG_SYS_MCLINK_MAX;
+	slaves = mclink_probe();
+	mclink_fpgacount = 0;
+
+	print_fpga_info(0, ch0_rgmii2_present);
+	osd_probe(0);
+
+	if (slaves <= 0)
+		return 0;
+
+	mclink_fpgacount = slaves;
+
+	for (k = 1; k <= slaves; ++k) {
+		FPGA_GET_REG(k, fpga_features, &fpga_features);
+
+		print_fpga_info(k, false);
+		osd_probe(k);
+		if (hw_type_cat) {
+			miiphy_register(bb_miiphy_buses[k].name,
+					bb_miiphy_read, bb_miiphy_write);
+			setup_88e1514(bb_miiphy_buses[k].name, 0);
+		}
+	}
+
+	return 0;
+}
+
+/*
+ * provide access to fpga gpios (for I2C bitbang)
+ * (these may look all too simple but make iocon.h much more readable)
+ */
+void fpga_gpio_set(unsigned int bus, int pin)
+{
+	FPGA_SET_REG(bus, gpio.set, pin);
+}
+
+void fpga_gpio_clear(unsigned int bus, int pin)
+{
+	FPGA_SET_REG(bus, gpio.clear, pin);
+}
+
+int fpga_gpio_get(unsigned int bus, int pin)
+{
+	u16 val;
+
+	FPGA_GET_REG(bus, gpio.read, &val);
+
+	return val & pin;
+}
+
+void mpc8308_init(void)
+{
+	pca9698_direction_output(0x20, 4, 1);
+}
+
+void mpc8308_set_fpga_reset(unsigned state)
+{
+	pca9698_set_value(0x20, 4, state ? 0 : 1);
+}
+
+void mpc8308_setup_hw(void)
+{
+	immap_t *immr = (immap_t *)CONFIG_SYS_IMMR;
+
+	/*
+	 * set "startup-finished"-gpios
+	 */
+	setbits_be32(&immr->gpio[0].dir, (1 << (31-11)) | (1 << (31-12)));
+	setbits_be32(&immr->gpio[0].dat, 1 << (31-12));
+}
+
+int mpc8308_get_fpga_done(unsigned fpga)
+{
+	return pca9698_get_value(0x20, 19);
+}
+
+#ifdef CONFIG_FSL_ESDHC
+int board_mmc_init(bd_t *bd)
+{
+	immap_t *immr = (immap_t *)CONFIG_SYS_IMMR;
+	sysconf83xx_t *sysconf = &immr->sysconf;
+
+	/* Enable cache snooping in eSDHC system configuration register */
+	out_be32(&sysconf->sdhccr, 0x02000000);
+
+	return fsl_esdhc_mmc_init(bd);
+}
+#endif
+
+static struct pci_region pcie_regions_0[] = {
+	{
+		.bus_start = CONFIG_SYS_PCIE1_MEM_BASE,
+		.phys_start = CONFIG_SYS_PCIE1_MEM_PHYS,
+		.size = CONFIG_SYS_PCIE1_MEM_SIZE,
+		.flags = PCI_REGION_MEM,
+	},
+	{
+		.bus_start = CONFIG_SYS_PCIE1_IO_BASE,
+		.phys_start = CONFIG_SYS_PCIE1_IO_PHYS,
+		.size = CONFIG_SYS_PCIE1_IO_SIZE,
+		.flags = PCI_REGION_IO,
+	},
+};
+
+void pci_init_board(void)
+{
+	immap_t *immr = (immap_t *)CONFIG_SYS_IMMR;
+	sysconf83xx_t *sysconf = &immr->sysconf;
+	law83xx_t *pcie_law = sysconf->pcielaw;
+	struct pci_region *pcie_reg[] = { pcie_regions_0 };
+
+	fsl_setup_serdes(CONFIG_FSL_SERDES1, FSL_SERDES_PROTO_PEX,
+			 FSL_SERDES_CLK_100, FSL_SERDES_VDD_1V);
+
+	/* Deassert the resets in the control register */
+	out_be32(&sysconf->pecr1, 0xE0008000);
+	udelay(2000);
+
+	/* Configure PCI Express Local Access Windows */
+	out_be32(&pcie_law[0].bar, CONFIG_SYS_PCIE1_BASE & LAWBAR_BAR);
+	out_be32(&pcie_law[0].ar, LBLAWAR_EN | LBLAWAR_512MB);
+
+	mpc83xx_pcie_init(1, pcie_reg);
+}
+
+ulong board_flash_get_legacy(ulong base, int banknum, flash_info_t *info)
+{
+	info->portwidth = FLASH_CFI_16BIT;
+	info->chipwidth = FLASH_CFI_BY16;
+	info->interface = FLASH_CFI_X16;
+	return 1;
+}
+
+#if defined(CONFIG_OF_BOARD_SETUP)
+void ft_board_setup(void *blob, bd_t *bd)
+{
+	ft_cpu_setup(blob, bd);
+	fdt_fixup_dr_usb(blob, bd);
+	fdt_fixup_esdhc(blob, bd);
+}
+#endif
+
+/*
+ * FPGA MII bitbang implementation
+ */
+
+struct fpga_mii {
+	unsigned fpga;
+	int mdio;
+} fpga_mii[] = {
+	{ 0, 1},
+	{ 1, 1},
+	{ 2, 1},
+	{ 3, 1},
+};
+
+static int mii_dummy_init(struct bb_miiphy_bus *bus)
+{
+	return 0;
+}
+
+static int mii_mdio_active(struct bb_miiphy_bus *bus)
+{
+	struct fpga_mii *fpga_mii = bus->priv;
+
+	if (fpga_mii->mdio)
+		FPGA_SET_REG(fpga_mii->fpga, gpio.set, GPIO_MDIO);
+	else
+		FPGA_SET_REG(fpga_mii->fpga, gpio.clear, GPIO_MDIO);
+
+	return 0;
+}
+
+static int mii_mdio_tristate(struct bb_miiphy_bus *bus)
+{
+	struct fpga_mii *fpga_mii = bus->priv;
+
+	FPGA_SET_REG(fpga_mii->fpga, gpio.set, GPIO_MDIO);
+
+	return 0;
+}
+
+static int mii_set_mdio(struct bb_miiphy_bus *bus, int v)
+{
+	struct fpga_mii *fpga_mii = bus->priv;
+
+	if (v)
+		FPGA_SET_REG(fpga_mii->fpga, gpio.set, GPIO_MDIO);
+	else
+		FPGA_SET_REG(fpga_mii->fpga, gpio.clear, GPIO_MDIO);
+
+	fpga_mii->mdio = v;
+
+	return 0;
+}
+
+static int mii_get_mdio(struct bb_miiphy_bus *bus, int *v)
+{
+	u16 gpio;
+	struct fpga_mii *fpga_mii = bus->priv;
+
+	FPGA_GET_REG(fpga_mii->fpga, gpio.read, &gpio);
+
+	*v = ((gpio & GPIO_MDIO) != 0);
+
+	return 0;
+}
+
+static int mii_set_mdc(struct bb_miiphy_bus *bus, int v)
+{
+	struct fpga_mii *fpga_mii = bus->priv;
+
+	if (v)
+		FPGA_SET_REG(fpga_mii->fpga, gpio.set, GPIO_MDC);
+	else
+		FPGA_SET_REG(fpga_mii->fpga, gpio.clear, GPIO_MDC);
+
+	return 0;
+}
+
+static int mii_delay(struct bb_miiphy_bus *bus)
+{
+	udelay(1);
+
+	return 0;
+}
+
+struct bb_miiphy_bus bb_miiphy_buses[] = {
+	{
+		.name = "board0",
+		.init = mii_dummy_init,
+		.mdio_active = mii_mdio_active,
+		.mdio_tristate = mii_mdio_tristate,
+		.set_mdio = mii_set_mdio,
+		.get_mdio = mii_get_mdio,
+		.set_mdc = mii_set_mdc,
+		.delay = mii_delay,
+		.priv = &fpga_mii[0],
+	},
+	{
+		.name = "board1",
+		.init = mii_dummy_init,
+		.mdio_active = mii_mdio_active,
+		.mdio_tristate = mii_mdio_tristate,
+		.set_mdio = mii_set_mdio,
+		.get_mdio = mii_get_mdio,
+		.set_mdc = mii_set_mdc,
+		.delay = mii_delay,
+		.priv = &fpga_mii[1],
+	},
+	{
+		.name = "board2",
+		.init = mii_dummy_init,
+		.mdio_active = mii_mdio_active,
+		.mdio_tristate = mii_mdio_tristate,
+		.set_mdio = mii_set_mdio,
+		.get_mdio = mii_get_mdio,
+		.set_mdc = mii_set_mdc,
+		.delay = mii_delay,
+		.priv = &fpga_mii[2],
+	},
+	{
+		.name = "board3",
+		.init = mii_dummy_init,
+		.mdio_active = mii_mdio_active,
+		.mdio_tristate = mii_mdio_tristate,
+		.set_mdio = mii_set_mdio,
+		.get_mdio = mii_get_mdio,
+		.set_mdc = mii_set_mdc,
+		.delay = mii_delay,
+		.priv = &fpga_mii[3],
+	},
+};
+
+int bb_miiphy_buses_num = sizeof(bb_miiphy_buses) /
+			  sizeof(bb_miiphy_buses[0]);
diff --git a/board/gdsys/mpc8308/mpc8308.c b/board/gdsys/mpc8308/mpc8308.c
new file mode 100644
index 0000000..4338a33
--- /dev/null
+++ b/board/gdsys/mpc8308/mpc8308.c
@@ -0,0 +1,109 @@
+/*
+ * (C) Copyright 2014
+ * Dirk Eibach,  Guntermann & Drunck GmbH, eibach@gdsys.de
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <command.h>
+#include <asm/processor.h>
+#include <asm/io.h>
+#include <asm/ppc4xx-gpio.h>
+#include <asm/global_data.h>
+
+#include "mpc8308.h"
+#include <gdsys_fpga.h>
+
+#define REFLECTION_TESTPATTERN 0xdede
+#define REFLECTION_TESTPATTERN_INV (~REFLECTION_TESTPATTERN & 0xffff)
+
+#ifdef CONFIG_SYS_FPGA_NO_RFL_HI
+#define REFLECTION_TESTREG reflection_low
+#else
+#define REFLECTION_TESTREG reflection_high
+#endif
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int get_fpga_state(unsigned dev)
+{
+	return gd->arch.fpga_state[dev];
+}
+
+void print_fpga_state(unsigned dev)
+{
+	if (gd->arch.fpga_state[dev] & FPGA_STATE_DONE_FAILED)
+		puts("       Waiting for FPGA-DONE timed out.\n");
+	if (gd->arch.fpga_state[dev] & FPGA_STATE_REFLECTION_FAILED)
+		puts("       FPGA reflection test failed.\n");
+}
+
+int board_early_init_f(void)
+{
+	unsigned k;
+
+	for (k = 0; k < CONFIG_SYS_FPGA_COUNT; ++k)
+		gd->arch.fpga_state[k] = 0;
+
+	return 0;
+}
+
+int board_early_init_r(void)
+{
+	unsigned k;
+	unsigned ctr;
+
+	for (k = 0; k < CONFIG_SYS_FPGA_COUNT; ++k)
+		gd->arch.fpga_state[k] = 0;
+
+	/*
+	 * reset FPGA
+	 */
+	mpc8308_init();
+
+	mpc8308_set_fpga_reset(1);
+
+	mpc8308_setup_hw();
+
+	for (k = 0; k < CONFIG_SYS_FPGA_COUNT; ++k) {
+		ctr = 0;
+		while (!mpc8308_get_fpga_done(k)) {
+			udelay(100000);
+			if (ctr++ > 5) {
+				gd->arch.fpga_state[k] |=
+					FPGA_STATE_DONE_FAILED;
+				break;
+			}
+		}
+	}
+
+	udelay(10);
+
+	mpc8308_set_fpga_reset(0);
+
+	for (k = 0; k < CONFIG_SYS_FPGA_COUNT; ++k) {
+		/*
+		 * wait for fpga out of reset
+		 */
+		ctr = 0;
+		while (1) {
+			u16 val;
+
+			FPGA_SET_REG(k, reflection_low, REFLECTION_TESTPATTERN);
+
+			FPGA_GET_REG(k, REFLECTION_TESTREG, &val);
+			if (val == REFLECTION_TESTPATTERN_INV)
+				break;
+
+			udelay(100000);
+			if (ctr++ > 5) {
+				gd->arch.fpga_state[k] |=
+					FPGA_STATE_REFLECTION_FAILED;
+				break;
+			}
+		}
+	}
+
+	return 0;
+}
diff --git a/board/gdsys/mpc8308/mpc8308.h b/board/gdsys/mpc8308/mpc8308.h
new file mode 100644
index 0000000..dc07d56
--- /dev/null
+++ b/board/gdsys/mpc8308/mpc8308.h
@@ -0,0 +1,10 @@
+#ifndef __MPC8308_H_
+#define __MPC8308_H_
+
+/* functions to be provided by board implementation */
+void mpc8308_init(void);
+void mpc8308_set_fpga_reset(unsigned state);
+void mpc8308_setup_hw(void);
+int mpc8308_get_fpga_done(unsigned fpga);
+
+#endif /* __MPC8308_H_ */
diff --git a/board/gdsys/mpc8308/sdram.c b/board/gdsys/mpc8308/sdram.c
new file mode 100644
index 0000000..0fce8cf
--- /dev/null
+++ b/board/gdsys/mpc8308/sdram.c
@@ -0,0 +1,82 @@
+/*
+ * Copyright (C) 2007 Freescale Semiconductor, Inc.
+ * Copyright (C) 2010 Ilya Yanok, Emcraft Systems, yanok@emcraft.com
+ *
+ * Authors: Nick.Spence@freescale.com
+ *          Wilson.Lo@freescale.com
+ *          scottwood@freescale.com
+ *
+ * This files is  mostly identical to the original from
+ * board\freescale\mpc8315erdb\sdram.c
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <mpc83xx.h>
+#include <spd_sdram.h>
+
+#include <asm/bitops.h>
+#include <asm/io.h>
+
+#include <asm/processor.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+/* Fixed sdram init -- doesn't use serial presence detect.
+ *
+ * This is useful for faster booting in configs where the RAM is unlikely
+ * to be changed, or for things like NAND booting where space is tight.
+ */
+static long fixed_sdram(void)
+{
+	immap_t *im = (immap_t *)CONFIG_SYS_IMMR;
+	u32 msize = CONFIG_SYS_DDR_SIZE * 1024 * 1024;
+	u32 msize_log2 = __ilog2(msize);
+
+	out_be32(&im->sysconf.ddrlaw[0].bar,
+		 CONFIG_SYS_DDR_SDRAM_BASE  & 0xfffff000);
+	out_be32(&im->sysconf.ddrlaw[0].ar, LBLAWAR_EN | (msize_log2 - 1));
+	out_be32(&im->sysconf.ddrcdr, CONFIG_SYS_DDRCDR_VALUE);
+
+	out_be32(&im->ddr.csbnds[0].csbnds, (msize - 1) >> 24);
+	out_be32(&im->ddr.cs_config[0], CONFIG_SYS_DDR_CS0_CONFIG);
+
+	/* Currently we use only one CS, so disable the other bank. */
+	out_be32(&im->ddr.cs_config[1], 0);
+
+	out_be32(&im->ddr.sdram_clk_cntl, CONFIG_SYS_DDR_SDRAM_CLK_CNTL);
+	out_be32(&im->ddr.timing_cfg_3, CONFIG_SYS_DDR_TIMING_3);
+	out_be32(&im->ddr.timing_cfg_1, CONFIG_SYS_DDR_TIMING_1);
+	out_be32(&im->ddr.timing_cfg_2, CONFIG_SYS_DDR_TIMING_2);
+	out_be32(&im->ddr.timing_cfg_0, CONFIG_SYS_DDR_TIMING_0);
+
+	out_be32(&im->ddr.sdram_cfg, CONFIG_SYS_DDR_SDRAM_CFG);
+	out_be32(&im->ddr.sdram_cfg2, CONFIG_SYS_DDR_SDRAM_CFG2);
+	out_be32(&im->ddr.sdram_mode, CONFIG_SYS_DDR_MODE);
+	out_be32(&im->ddr.sdram_mode2, CONFIG_SYS_DDR_MODE2);
+
+	out_be32(&im->ddr.sdram_interval, CONFIG_SYS_DDR_INTERVAL);
+	sync();
+
+	/* enable DDR controller */
+	setbits_be32(&im->ddr.sdram_cfg, SDRAM_CFG_MEM_EN);
+	sync();
+
+	return get_ram_size(CONFIG_SYS_DDR_SDRAM_BASE, msize);
+}
+
+phys_size_t initdram(int board_type)
+{
+	immap_t *im = (immap_t *)CONFIG_SYS_IMMR;
+	u32 msize;
+
+	if ((in_be32(&im->sysconf.immrbar) & IMMRBAR_BASE_ADDR) != (u32)im)
+		return -1;
+
+	/* DDR SDRAM */
+	msize = fixed_sdram();
+
+	/* return total bus SDRAM size(bytes)  -- DDR */
+	return msize;
+}
diff --git a/configs/hrcon_defconfig b/configs/hrcon_defconfig
new file mode 100644
index 0000000..69c65ba
--- /dev/null
+++ b/configs/hrcon_defconfig
@@ -0,0 +1,3 @@
+CONFIG_PPC=y
+CONFIG_MPC83xx=y
+CONFIG_TARGET_HRCON=y
diff --git a/include/configs/hrcon.h b/include/configs/hrcon.h
new file mode 100644
index 0000000..e7df9ad
--- /dev/null
+++ b/include/configs/hrcon.h
@@ -0,0 +1,614 @@
+/*
+ * (C) Copyright 2014
+ * Dirk Eibach,  Guntermann & Drunck GmbH, eibach@gdsys.de
+ *
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ */
+#define CONFIG_E300		1 /* E300 family */
+#define CONFIG_MPC83xx		1 /* MPC83xx family */
+#define CONFIG_MPC830x		1 /* MPC830x family */
+#define CONFIG_MPC8308		1 /* MPC8308 CPU specific */
+#define CONFIG_HRCON		1 /* HRCON board specific */
+
+#define	CONFIG_SYS_TEXT_BASE	0xFE000000
+
+#define CONFIG_IDENT_STRING	" hrcon 0.01"
+
+#define CONFIG_SYS_GENERIC_BOARD
+
+#define CONFIG_BOARD_EARLY_INIT_F
+#define CONFIG_BOARD_EARLY_INIT_R
+#define CONFIG_LAST_STAGE_INIT
+
+/* new uImage format support */
+#define CONFIG_FIT			1
+#define CONFIG_FIT_VERBOSE		1
+
+#define CONFIG_MMC
+#define CONFIG_FSL_ESDHC
+#define CONFIG_SYS_FSL_ESDHC_ADDR	CONFIG_SYS_MPC83xx_ESDHC_ADDR
+#define CONFIG_SYS_FSL_ERRATUM_ESDHC111
+
+#define CONFIG_CMD_MMC
+#define CONFIG_GENERIC_MMC
+#define CONFIG_DOS_PARTITION
+#define CONFIG_CMD_EXT2
+
+#define CONFIG_CMD_FPGAD
+#define CONFIG_CMD_IOLOOP
+
+/*
+ * System Clock Setup
+ */
+#define CONFIG_83XX_CLKIN	33333333 /* in Hz */
+#define CONFIG_SYS_CLK_FREQ	CONFIG_83XX_CLKIN
+
+/*
+ * Hardware Reset Configuration Word
+ * if CLKIN is 66.66MHz, then
+ * CSB = 133MHz, DDRC = 266MHz, LBC = 133MHz
+ * We choose the A type silicon as default, so the core is 400Mhz.
+ */
+#define CONFIG_SYS_HRCW_LOW (\
+	HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
+	HRCWL_DDR_TO_SCB_CLK_2X1 |\
+	HRCWL_SVCOD_DIV_2 |\
+	HRCWL_CSB_TO_CLKIN_4X1 |\
+	HRCWL_CORE_TO_CSB_3X1)
+/*
+ * There are neither HRCWH_PCI_HOST nor HRCWH_PCI1_ARBITER_ENABLE bits
+ * in 8308's HRCWH according to the manual, but original Freescale's
+ * code has them and I've expirienced some problems using the board
+ * with BDI3000 attached when I've tried to set these bits to zero
+ * (UART doesn't work after the 'reset run' command).
+ */
+#define CONFIG_SYS_HRCW_HIGH (\
+	HRCWH_PCI_HOST |\
+	HRCWH_PCI1_ARBITER_ENABLE |\
+	HRCWH_CORE_ENABLE |\
+	HRCWH_FROM_0XFFF00100 |\
+	HRCWH_BOOTSEQ_DISABLE |\
+	HRCWH_SW_WATCHDOG_DISABLE |\
+	HRCWH_ROM_LOC_LOCAL_16BIT |\
+	HRCWH_RL_EXT_LEGACY |\
+	HRCWH_TSEC1M_IN_RGMII |\
+	HRCWH_TSEC2M_IN_RGMII |\
+	HRCWH_BIG_ENDIAN)
+
+/*
+ * System IO Config
+ */
+#define CONFIG_SYS_SICRH (\
+	SICRH_ESDHC_A_SD |\
+	SICRH_ESDHC_B_SD |\
+	SICRH_ESDHC_C_SD |\
+	SICRH_GPIO_A_GPIO |\
+	SICRH_GPIO_B_GPIO |\
+	SICRH_IEEE1588_A_GPIO |\
+	SICRH_USB |\
+	SICRH_GTM_GPIO |\
+	SICRH_IEEE1588_B_GPIO |\
+	SICRH_ETSEC2_GPIO |\
+	SICRH_GPIOSEL_1 |\
+	SICRH_TMROBI_V3P3 |\
+	SICRH_TSOBI1_V2P5 |\
+	SICRH_TSOBI2_V2P5)	/* 0x0037f103 */
+#define CONFIG_SYS_SICRL (\
+	SICRL_SPI_PF0 |\
+	SICRL_UART_PF0 |\
+	SICRL_IRQ_PF0 |\
+	SICRL_I2C2_PF0 |\
+	SICRL_ETSEC1_GTX_CLK125)	/* 0x00000000 */
+
+/*
+ * IMMR new address
+ */
+#define CONFIG_SYS_IMMR		0xE0000000
+
+/*
+ * SERDES
+ */
+#define CONFIG_FSL_SERDES
+#define CONFIG_FSL_SERDES1	0xe3000
+
+/*
+ * Arbiter Setup
+ */
+#define CONFIG_SYS_ACR_PIPE_DEP	3 /* Arbiter pipeline depth is 4 */
+#define CONFIG_SYS_ACR_RPTCNT	3 /* Arbiter repeat count is 4 */
+#define CONFIG_SYS_SPCR_TSECEP	3 /* eTSEC emergency priority is highest */
+
+/*
+ * DDR Setup
+ */
+#define CONFIG_SYS_DDR_BASE		0x00000000 /* DDR is system memory */
+#define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_BASE
+#define CONFIG_SYS_DDR_SDRAM_BASE	CONFIG_SYS_DDR_BASE
+#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL	DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
+#define CONFIG_SYS_DDRCDR_VALUE	(DDRCDR_EN \
+				| DDRCDR_PZ_LOZ \
+				| DDRCDR_NZ_LOZ \
+				| DDRCDR_ODT \
+				| DDRCDR_Q_DRN)
+				/* 0x7b880001 */
+/*
+ * Manually set up DDR parameters
+ * consist of one chip NT5TU64M16HG from NANYA
+ */
+
+#define CONFIG_SYS_DDR_SIZE		128 /* MB */
+
+#define CONFIG_SYS_DDR_CS0_BNDS	0x00000007
+#define CONFIG_SYS_DDR_CS0_CONFIG	(CSCONFIG_EN \
+				| CSCONFIG_ODT_RD_NEVER \
+				| CSCONFIG_ODT_WR_ONLY_CURRENT \
+				| CSCONFIG_BANK_BIT_3 \
+				| CSCONFIG_ROW_BIT_13 | CSCONFIG_COL_BIT_10)
+				/* 0x80010102 */
+#define CONFIG_SYS_DDR_TIMING_3	0
+#define CONFIG_SYS_DDR_TIMING_0	((0 << TIMING_CFG0_RWT_SHIFT) \
+				| (0 << TIMING_CFG0_WRT_SHIFT) \
+				| (0 << TIMING_CFG0_RRT_SHIFT) \
+				| (0 << TIMING_CFG0_WWT_SHIFT) \
+				| (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \
+				| (6 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \
+				| (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \
+				| (2 << TIMING_CFG0_MRS_CYC_SHIFT))
+				/* 0x00260802 */
+#define CONFIG_SYS_DDR_TIMING_1	((2 << TIMING_CFG1_PRETOACT_SHIFT) \
+				| (6 << TIMING_CFG1_ACTTOPRE_SHIFT) \
+				| (2 << TIMING_CFG1_ACTTORW_SHIFT) \
+				| (7 << TIMING_CFG1_CASLAT_SHIFT) \
+				| (9 << TIMING_CFG1_REFREC_SHIFT) \
+				| (2 << TIMING_CFG1_WRREC_SHIFT) \
+				| (2 << TIMING_CFG1_ACTTOACT_SHIFT) \
+				| (2 << TIMING_CFG1_WRTORD_SHIFT))
+				/* 0x26279222 */
+#define CONFIG_SYS_DDR_TIMING_2	((0 << TIMING_CFG2_ADD_LAT_SHIFT) \
+				| (4 << TIMING_CFG2_CPO_SHIFT) \
+				| (3 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \
+				| (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) \
+				| (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \
+				| (3 << TIMING_CFG2_CKE_PLS_SHIFT) \
+				| (5 << TIMING_CFG2_FOUR_ACT_SHIFT))
+				/* 0x021848c5 */
+#define CONFIG_SYS_DDR_INTERVAL	((0x0824 << SDRAM_INTERVAL_REFINT_SHIFT) \
+				| (0x0100 << SDRAM_INTERVAL_BSTOPRE_SHIFT))
+				/* 0x08240100 */
+#define CONFIG_SYS_DDR_SDRAM_CFG	(SDRAM_CFG_SREN \
+				| SDRAM_CFG_SDRAM_TYPE_DDR2 \
+				| SDRAM_CFG_DBW_16)
+				/* 0x43100000 */
+
+#define CONFIG_SYS_DDR_SDRAM_CFG2	0x00401000 /* 1 posted refresh */
+#define CONFIG_SYS_DDR_MODE		((0x0440 << SDRAM_MODE_ESD_SHIFT) \
+				| (0x0242 << SDRAM_MODE_SD_SHIFT))
+				/* ODT 150ohm CL=4, AL=0 on SDRAM */
+#define CONFIG_SYS_DDR_MODE2		0x00000000
+
+/*
+ * Memory test
+ */
+#define CONFIG_SYS_MEMTEST_START	0x00001000 /* memtest region */
+#define CONFIG_SYS_MEMTEST_END		0x07f00000
+
+/*
+ * The reserved memory
+ */
+#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE /* start of monitor */
+
+#define CONFIG_SYS_MONITOR_LEN	(384 * 1024) /* Reserve 384 kB for Mon */
+#define CONFIG_SYS_MALLOC_LEN	(512 * 1024) /* Reserved for malloc */
+
+/*
+ * Initial RAM Base Address Setup
+ */
+#define CONFIG_SYS_INIT_RAM_LOCK	1
+#define CONFIG_SYS_INIT_RAM_ADDR	0xE6000000 /* Initial RAM address */
+#define CONFIG_SYS_INIT_RAM_SIZE	0x1000 /* Size of used area in RAM */
+#define CONFIG_SYS_GBL_DATA_OFFSET	\
+	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+
+/*
+ * Local Bus Configuration & Clock Setup
+ */
+#define CONFIG_SYS_LCRR_DBYP		LCRR_DBYP
+#define CONFIG_SYS_LCRR_CLKDIV		LCRR_CLKDIV_2
+#define CONFIG_SYS_LBC_LBCR		0x00040000
+
+/*
+ * FLASH on the Local Bus
+ */
+#if 1
+#define CONFIG_SYS_FLASH_CFI		/* use the Common Flash Interface */
+#define CONFIG_FLASH_CFI_DRIVER		/* use the CFI driver */
+#define CONFIG_SYS_FLASH_CFI_WIDTH	FLASH_CFI_16BIT
+#define CONFIG_FLASH_CFI_LEGACY
+#define CONFIG_SYS_FLASH_LEGACY_512Kx16
+#else
+#define CONFIG_SYS_NO_FLASH
+#endif
+
+#define CONFIG_SYS_FLASH_BASE		0xFE000000 /* FLASH base address */
+#define CONFIG_SYS_FLASH_SIZE		8 /* FLASH size is up to 8M */
+#define CONFIG_SYS_FLASH_PROTECTION	1 /* Use h/w Flash protection. */
+
+/* Window base at flash base */
+#define CONFIG_SYS_LBLAWBAR0_PRELIM	CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_LBLAWAR0_PRELIM	(LBLAWAR_EN | LBLAWAR_8MB)
+
+#define CONFIG_SYS_BR0_PRELIM	(CONFIG_SYS_FLASH_BASE \
+				| BR_PS_16	/* 16 bit port */ \
+				| BR_MS_GPCM	/* MSEL = GPCM */ \
+				| BR_V)		/* valid */
+#define CONFIG_SYS_OR0_PRELIM	(MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \
+				| OR_UPM_XAM \
+				| OR_GPCM_CSNT \
+				| OR_GPCM_ACS_DIV2 \
+				| OR_GPCM_XACS \
+				| OR_GPCM_SCY_15 \
+				| OR_GPCM_TRLX_SET \
+				| OR_GPCM_EHTR_SET)
+
+#define CONFIG_SYS_MAX_FLASH_BANKS	1 /* number of banks */
+#define CONFIG_SYS_MAX_FLASH_SECT	135
+
+#define CONFIG_SYS_FLASH_ERASE_TOUT	60000 /* Flash Erase Timeout (ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT	500 /* Flash Write Timeout (ms) */
+
+/*
+ * FPGA
+ */
+#define CONFIG_SYS_FPGA0_BASE		0xE0600000
+#define CONFIG_SYS_FPGA0_SIZE		1 /* FPGA size is 1M */
+
+/* Window base at FPGA base */
+#define CONFIG_SYS_LBLAWBAR1_PRELIM	CONFIG_SYS_FPGA0_BASE
+#define CONFIG_SYS_LBLAWAR1_PRELIM	(LBLAWAR_EN | LBLAWAR_1MB)
+
+#define CONFIG_SYS_BR1_PRELIM	(CONFIG_SYS_FPGA0_BASE \
+				| BR_PS_16	/* 16 bit port */ \
+				| BR_MS_GPCM	/* MSEL = GPCM */ \
+				| BR_V)		/* valid */
+#define CONFIG_SYS_OR1_PRELIM	(MEG_TO_AM(CONFIG_SYS_FPGA0_SIZE) \
+				| OR_UPM_XAM \
+				| OR_GPCM_CSNT \
+				| OR_GPCM_ACS_DIV2 \
+				| OR_GPCM_XACS \
+				| OR_GPCM_SCY_15 \
+				| OR_GPCM_TRLX_SET \
+				| OR_GPCM_EHTR_SET)
+
+#define CONFIG_SYS_FPGA_BASE(k)		CONFIG_SYS_FPGA0_BASE
+#define CONFIG_SYS_FPGA_DONE(k)		0x0010
+
+#define CONFIG_SYS_FPGA_COUNT		1
+
+#define CONFIG_SYS_MCLINK_MAX		3
+
+#define CONFIG_SYS_FPGA_PTR \
+	{ (struct ihs_fpga *)CONFIG_SYS_FPGA0_BASE, NULL, NULL, NULL }
+
+/*
+ * Serial Port
+ */
+#define CONFIG_CONS_INDEX	2
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE	1
+#define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)
+
+#define CONFIG_SYS_BAUDRATE_TABLE  \
+	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
+
+#define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_IMMR + 0x4500)
+#define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_IMMR + 0x4600)
+
+/* Use the HUSH parser */
+#define CONFIG_SYS_HUSH_PARSER
+
+/* Pass open firmware flat tree */
+#define CONFIG_OF_LIBFDT		1
+#define CONFIG_OF_BOARD_SETUP		1
+#define CONFIG_OF_STDOUT_VIA_ALIAS	1
+
+/* I2C */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED	400000
+#define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET	0x3000
+
+#define CONFIG_PCA953X			/* NXP PCA9554 */
+#define CONFIG_PCA9698			/* NXP PCA9698 */
+
+#define CONFIG_SYS_I2C_IHS
+#define CONFIG_SYS_I2C_IHS_CH0
+#define CONFIG_SYS_I2C_IHS_SPEED_0		50000
+#define CONFIG_SYS_I2C_IHS_SLAVE_0		0x7F
+#define CONFIG_SYS_I2C_IHS_CH1
+#define CONFIG_SYS_I2C_IHS_SPEED_1		50000
+#define CONFIG_SYS_I2C_IHS_SLAVE_1		0x7F
+#define CONFIG_SYS_I2C_IHS_CH2
+#define CONFIG_SYS_I2C_IHS_SPEED_2		50000
+#define CONFIG_SYS_I2C_IHS_SLAVE_2		0x7F
+#define CONFIG_SYS_I2C_IHS_CH3
+#define CONFIG_SYS_I2C_IHS_SPEED_3		50000
+#define CONFIG_SYS_I2C_IHS_SLAVE_3		0x7F
+
+/*
+ * Software (bit-bang) I2C driver configuration
+ */
+#define CONFIG_SYS_I2C_SOFT
+#define CONFIG_SYS_I2C_SOFT_SPEED		50000
+#define CONFIG_SYS_I2C_SOFT_SLAVE		0x7F
+#define I2C_SOFT_DECLARATIONS2
+#define CONFIG_SYS_I2C_SOFT_SPEED_2		50000
+#define CONFIG_SYS_I2C_SOFT_SLAVE_2		0x7F
+#define I2C_SOFT_DECLARATIONS3
+#define CONFIG_SYS_I2C_SOFT_SPEED_3		50000
+#define CONFIG_SYS_I2C_SOFT_SLAVE_3		0x7F
+#define I2C_SOFT_DECLARATIONS4
+#define CONFIG_SYS_I2C_SOFT_SPEED_4		50000
+#define CONFIG_SYS_I2C_SOFT_SLAVE_4		0x7F
+
+#define CONFIG_SYS_ICS8N3QV01_I2C		{5, 6, 7, 8}
+#define CONFIG_SYS_CH7301_I2C			{5, 6, 7, 8}
+#define CONFIG_SYS_DP501_I2C			{1, 2, 3, 4}
+
+#ifndef __ASSEMBLY__
+void fpga_gpio_set(unsigned int bus, int pin);
+void fpga_gpio_clear(unsigned int bus, int pin);
+int fpga_gpio_get(unsigned int bus, int pin);
+#endif
+
+#define I2C_ACTIVE	{ }
+#define I2C_TRISTATE	{ }
+#define I2C_READ \
+	(fpga_gpio_get(I2C_ADAP_HWNR, 0x0040) ? 1 : 0)
+#define I2C_SDA(bit) \
+	do { \
+		if (bit) \
+			fpga_gpio_set(I2C_ADAP_HWNR, 0x0040); \
+		else \
+			fpga_gpio_clear(I2C_ADAP_HWNR, 0x0040); \
+	} while (0)
+#define I2C_SCL(bit) \
+	do { \
+		if (bit) \
+			fpga_gpio_set(I2C_ADAP_HWNR, 0x0020); \
+		else \
+			fpga_gpio_clear(I2C_ADAP_HWNR, 0x0020); \
+	} while (0)
+#define I2C_DELAY	udelay(25)	/* 1/4 I2C clock duration */
+
+/*
+ * Software (bit-bang) MII driver configuration
+ */
+#define CONFIG_BITBANGMII		/* bit-bang MII PHY management */
+#define CONFIG_BITBANGMII_MULTI
+
+/*
+ * OSD Setup
+ */
+#define CONFIG_SYS_OSD_SCREENS		1
+#define CONFIG_SYS_DP501_DIFFERENTIAL
+#define CONFIG_SYS_DP501_VCAPCTRL0	0x01 /* DDR mode 0, DE for H/VSYNC */
+
+/*
+ * General PCI
+ * Addresses are mapped 1-1.
+ */
+#define CONFIG_SYS_PCIE1_BASE		0xA0000000
+#define CONFIG_SYS_PCIE1_MEM_BASE	0xA0000000
+#define CONFIG_SYS_PCIE1_MEM_PHYS	0xA0000000
+#define CONFIG_SYS_PCIE1_MEM_SIZE	0x10000000
+#define CONFIG_SYS_PCIE1_CFG_BASE	0xB0000000
+#define CONFIG_SYS_PCIE1_CFG_SIZE	0x01000000
+#define CONFIG_SYS_PCIE1_IO_BASE	0x00000000
+#define CONFIG_SYS_PCIE1_IO_PHYS	0xB1000000
+#define CONFIG_SYS_PCIE1_IO_SIZE	0x00800000
+
+/* enable PCIE clock */
+#define CONFIG_SYS_SCCR_PCIEXP1CM	1
+
+#define CONFIG_PCI
+#define CONFIG_PCI_INDIRECT_BRIDGE
+#define CONFIG_PCIE
+
+#define CONFIG_PCI_PNP		/* do pci plug-and-play */
+
+#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957	/* Freescale */
+#define CONFIG_83XX_GENERIC_PCIE_REGISTER_HOSES 1
+
+/*
+ * TSEC
+ */
+#define CONFIG_TSEC_ENET	/* TSEC ethernet support */
+#define CONFIG_SYS_TSEC1_OFFSET	0x24000
+#define CONFIG_SYS_TSEC1	(CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET)
+
+/*
+ * TSEC ethernet configuration
+ */
+#define CONFIG_MII		1 /* MII PHY management */
+#define CONFIG_TSEC1
+#define CONFIG_TSEC1_NAME	"eTSEC0"
+#define TSEC1_PHY_ADDR		1
+#define TSEC1_PHYIDX		0
+#define TSEC1_FLAGS		TSEC_GIGABIT
+
+/* Options are: eTSEC[0-1] */
+#define CONFIG_ETHPRIME		"eTSEC0"
+
+/*
+ * Environment
+ */
+#if 1
+#define CONFIG_ENV_IS_IN_FLASH	1
+#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE + \
+				 CONFIG_SYS_MONITOR_LEN)
+#define CONFIG_ENV_SECT_SIZE	0x10000 /* 64K(one sector) for env */
+#define CONFIG_ENV_SIZE		0x2000
+#define CONFIG_ENV_ADDR_REDUND	(CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE_REDUND	CONFIG_ENV_SIZE
+#else
+#define CONFIG_ENV_IS_NOWHERE
+#define CONFIG_ENV_SIZE		0x2000		/* 8KB */
+#endif
+
+#define CONFIG_LOADS_ECHO	1	/* echo on for serial download */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change */
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_PING
+
+#define CONFIG_CMDLINE_EDITING	1	/* add command line history */
+#define CONFIG_AUTO_COMPLETE		/* add autocompletion support */
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LONGHELP		/* undef to save memory */
+#define CONFIG_SYS_LOAD_ADDR		0x2000000 /* default load address */
+#define CONFIG_SYS_PROMPT		"=> "	/* Monitor Command Prompt */
+#define CONFIG_SYS_HZ		1000	/* decrementer freq: 1ms ticks */
+
+#undef CONFIG_ZERO_BOOTDELAY_CHECK	/* ignore keypress on bootdelay==0 */
+#define CONFIG_AUTOBOOT_KEYED		/* use key strings to stop autoboot */
+#define CONFIG_AUTOBOOT_STOP_STR " "
+
+#define CONFIG_SYS_CBSIZE	1024 /* Console I/O Buffer Size */
+
+#define CONFIG_SYS_CONSOLE_INFO_QUIET
+
+/* Print Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_MAXARGS	16	/* max number of command args */
+#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 256 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ	(256 << 20) /* Initial Memory map for Linux */
+
+/*
+ * Core HID Setup
+ */
+#define CONFIG_SYS_HID0_INIT	0x000000000
+#define CONFIG_SYS_HID0_FINAL	(HID0_ENABLE_MACHINE_CHECK | \
+				 HID0_ENABLE_INSTRUCTION_CACHE | \
+				 HID0_ENABLE_DYNAMIC_POWER_MANAGMENT)
+#define CONFIG_SYS_HID2		HID2_HBE
+
+/*
+ * MMU Setup
+ */
+
+/* DDR: cache cacheable */
+#define CONFIG_SYS_IBAT0L	(CONFIG_SYS_SDRAM_BASE | BATL_PP_RW | \
+					BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT0U	(CONFIG_SYS_SDRAM_BASE | BATU_BL_128M | \
+					BATU_VS | BATU_VP)
+#define CONFIG_SYS_DBAT0L	CONFIG_SYS_IBAT0L
+#define CONFIG_SYS_DBAT0U	CONFIG_SYS_IBAT0U
+
+/* IMMRBAR, PCI IO and FPGA: cache-inhibit and guarded */
+#define CONFIG_SYS_IBAT1L	(CONFIG_SYS_IMMR | BATL_PP_RW | \
+			BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_IBAT1U	(CONFIG_SYS_IMMR | BATU_BL_8M | BATU_VS | \
+					BATU_VP)
+#define CONFIG_SYS_DBAT1L	CONFIG_SYS_IBAT1L
+#define CONFIG_SYS_DBAT1U	CONFIG_SYS_IBAT1U
+
+/* FLASH: icache cacheable, but dcache-inhibit and guarded */
+#define CONFIG_SYS_IBAT2L	(CONFIG_SYS_FLASH_BASE | BATL_PP_RW | \
+					BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT2U	(CONFIG_SYS_FLASH_BASE | BATU_BL_8M | \
+					BATU_VS | BATU_VP)
+#define CONFIG_SYS_DBAT2L	(CONFIG_SYS_FLASH_BASE | BATL_PP_RW | \
+					BATL_CACHEINHIBIT | \
+					BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_DBAT2U	CONFIG_SYS_IBAT2U
+
+/* Stack in dcache: cacheable, no memory coherence */
+#define CONFIG_SYS_IBAT3L	(CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW)
+#define CONFIG_SYS_IBAT3U	(CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | \
+					BATU_VS | BATU_VP)
+#define CONFIG_SYS_DBAT3L	CONFIG_SYS_IBAT3L
+#define CONFIG_SYS_DBAT3U	CONFIG_SYS_IBAT3U
+
+/*
+ * Environment Configuration
+ */
+
+#define CONFIG_ENV_OVERWRITE
+
+#if defined(CONFIG_TSEC_ENET)
+#define CONFIG_HAS_ETH0
+#endif
+
+#define CONFIG_BAUDRATE 115200
+
+#define CONFIG_LOADADDR	800000	/* default location for tftp and bootm */
+
+#define CONFIG_BOOTDELAY	5	/* -1 disables auto-boot */
+
+#define CONFIG_HOSTNAME		hrcon
+#define CONFIG_ROOTPATH		"/opt/nfsroot"
+#define CONFIG_BOOTFILE		"uImage"
+
+#define CONFIG_PREBOOT		/* enable preboot variable */
+
+#define	CONFIG_EXTRA_ENV_SETTINGS					\
+	"netdev=eth0\0"							\
+	"consoledev=ttyS1\0"						\
+	"u-boot=u-boot.bin\0"						\
+	"kernel_addr=1000000\0"					\
+	"fdt_addr=C00000\0"						\
+	"fdtfile=hrcon.dtb\0"				\
+	"load=tftp ${loadaddr} ${u-boot}\0"				\
+	"update=protect off " __stringify(CONFIG_SYS_MONITOR_BASE)	\
+		" +${filesize};era " __stringify(CONFIG_SYS_MONITOR_BASE)\
+		" +${filesize};cp.b ${fileaddr} "			\
+		__stringify(CONFIG_SYS_MONITOR_BASE) " ${filesize}\0"	\
+	"upd=run load update\0"						\
+
+#define CONFIG_NFSBOOTCOMMAND						\
+	"setenv bootargs root=/dev/nfs rw "				\
+	"nfsroot=$serverip:$rootpath "					\
+	"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
+	"console=$consoledev,$baudrate $othbootargs;"			\
+	"tftp ${kernel_addr} $bootfile;"				\
+	"tftp ${fdt_addr} $fdtfile;"					\
+	"bootm ${kernel_addr} - ${fdt_addr}"
+
+#define CONFIG_MMCBOOTCOMMAND						\
+	"setenv bootargs root=/dev/mmcblk0p3 rw rootwait "		\
+	"console=$consoledev,$baudrate $othbootargs;"			\
+	"ext2load mmc 0:2 ${kernel_addr} $bootfile;"			\
+	"ext2load mmc 0:2 ${fdt_addr} $fdtfile;"			\
+	"bootm ${kernel_addr} - ${fdt_addr}"
+
+#define CONFIG_BOOTCOMMAND		CONFIG_MMCBOOTCOMMAND
+
+
+#endif	/* __CONFIG_H */
diff --git a/include/gdsys_fpga.h b/include/gdsys_fpga.h
index 276a01e..8a5efe7 100644
--- a/include/gdsys_fpga.h
+++ b/include/gdsys_fpga.h
@@ -61,6 +61,22 @@
 	u16 y_pos;
 };
 
+struct ihs_mdio {
+	u16 control;
+	u16 address_data;
+	u16 rx_data;
+};
+
+struct ihs_io_ep {
+	u16 transmit_data;
+	u16 rx_tx_control;
+	u16 receive_data;
+	u16 rx_tx_status;
+	u16 reserved;
+	u16 device_address;
+	u16 target_address;
+};
+
 #ifdef CONFIG_NEO
 struct ihs_fpga {
 	u16 reflection_low;	/* 0x0000 */
@@ -119,12 +135,16 @@
 	u16 versions;		/* 0x0002 */
 	u16 fpga_version;	/* 0x0004 */
 	u16 fpga_features;	/* 0x0006 */
-	u16 reserved_0[6];	/* 0x0008 */
+	u16 reserved_0[1];	/* 0x0008 */
+	u16 top_interrupt;	/* 0x000a */
+	u16 reserved_1[4];	/* 0x000c */
 	struct ihs_gpio gpio;	/* 0x0014 */
 	u16 mpc3w_control;	/* 0x001a */
-	u16 reserved_1[18];	/* 0x001c */
+	u16 reserved_2[2];	/* 0x001c */
+	struct ihs_io_ep ep;	/* 0x0020 */
+	u16 reserved_3[9];	/* 0x002e */
 	struct ihs_i2c i2c;	/* 0x0040 */
-	u16 reserved_2[10];	/* 0x004c */
+	u16 reserved_4[10];	/* 0x004c */
 	u16 mc_int;		/* 0x0060 */
 	u16 mc_int_en;		/* 0x0062 */
 	u16 mc_status;		/* 0x0064 */
@@ -135,10 +155,44 @@
 	u16 mc_res;		/* 0x006e */
 	u16 mc_rx_cmd_status;	/* 0x0070 */
 	u16 mc_rx_data;		/* 0x0072 */
-	u16 reserved_3[69];	/* 0x0074 */
+	u16 reserved_5[69];	/* 0x0074 */
 	u16 reflection_high;	/* 0x00fe */
 	struct ihs_osd osd;	/* 0x0100 */
-	u16 reserved_4[889];	/* 0x010e */
+	u16 reserved_6[889];	/* 0x010e */
+	u16 videomem[31736];	/* 0x0800 */
+};
+#endif
+
+#ifdef CONFIG_HRCON
+struct ihs_fpga {
+	u16 reflection_low;	/* 0x0000 */
+	u16 versions;		/* 0x0002 */
+	u16 fpga_version;	/* 0x0004 */
+	u16 fpga_features;	/* 0x0006 */
+	u16 reserved_0[1];	/* 0x0008 */
+	u16 top_interrupt;	/* 0x000a */
+	u16 reserved_1[4];	/* 0x000c */
+	struct ihs_gpio gpio;	/* 0x0014 */
+	u16 mpc3w_control;	/* 0x001a */
+	u16 reserved_2[2];	/* 0x001c */
+	struct ihs_io_ep ep;	/* 0x0020 */
+	u16 reserved_3[9];	/* 0x002e */
+	struct ihs_i2c i2c;	/* 0x0040 */
+	u16 reserved_4[10];	/* 0x004c */
+	u16 mc_int;		/* 0x0060 */
+	u16 mc_int_en;		/* 0x0062 */
+	u16 mc_status;		/* 0x0064 */
+	u16 mc_control;		/* 0x0066 */
+	u16 mc_tx_data;		/* 0x0068 */
+	u16 mc_tx_address;	/* 0x006a */
+	u16 mc_tx_cmd;		/* 0x006c */
+	u16 mc_res;		/* 0x006e */
+	u16 mc_rx_cmd_status;	/* 0x0070 */
+	u16 mc_rx_data;		/* 0x0072 */
+	u16 reserved_5[69];	/* 0x0074 */
+	u16 reflection_high;	/* 0x00fe */
+	struct ihs_osd osd;	/* 0x0100 */
+	u16 reserved_6[889];	/* 0x010e */
 	u16 videomem[31736];	/* 0x0800 */
 };
 #endif