mpc83xx: Add gdsys hrcon board
The gdsys hrcon board is based on a Freescale MPC8308 SOC.
It boots from NOR-Flash, kernel and rootfs are stored on
SD-Card.
On board peripherals include:
- 1x GbE (optional)
- Lattice ECP3 FPGA connected via eLBC and PCIe
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
diff --git a/board/gdsys/mpc8308/Kconfig b/board/gdsys/mpc8308/Kconfig
new file mode 100644
index 0000000..43e1663
--- /dev/null
+++ b/board/gdsys/mpc8308/Kconfig
@@ -0,0 +1,12 @@
+if TARGET_HRCON
+
+config SYS_BOARD
+ default "mpc8308"
+
+config SYS_VENDOR
+ default "gdsys"
+
+config SYS_CONFIG_NAME
+ default "hrcon"
+
+endif
diff --git a/board/gdsys/mpc8308/MAINTAINERS b/board/gdsys/mpc8308/MAINTAINERS
new file mode 100644
index 0000000..a7853a5
--- /dev/null
+++ b/board/gdsys/mpc8308/MAINTAINERS
@@ -0,0 +1,6 @@
+MPC8308 BOARD
+M: Dirk Eibach <eibach@gdsys.de>
+S: Maintained
+F: board/gdsys/mpc8308/
+F: include/configs/hrcon.h
+F: configs/hrcon_defconfig
diff --git a/board/gdsys/mpc8308/Makefile b/board/gdsys/mpc8308/Makefile
new file mode 100644
index 0000000..b5dfdbb
--- /dev/null
+++ b/board/gdsys/mpc8308/Makefile
@@ -0,0 +1,9 @@
+#
+# (C) Copyright 2014
+# Dirk Eibach, Guntermann & Drunck GmbH, eibach@gdsys.de
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+obj-y := mpc8308.o sdram.o
+obj-$(CONFIG_HRCON) += hrcon.o
diff --git a/board/gdsys/mpc8308/hrcon.c b/board/gdsys/mpc8308/hrcon.c
new file mode 100644
index 0000000..a051682
--- /dev/null
+++ b/board/gdsys/mpc8308/hrcon.c
@@ -0,0 +1,675 @@
+/*
+ * (C) Copyright 2014
+ * Dirk Eibach, Guntermann & Drunck GmbH, eibach@gdsys.de
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <hwconfig.h>
+#include <i2c.h>
+#include <spi.h>
+#include <libfdt.h>
+#include <fdt_support.h>
+#include <pci.h>
+#include <mpc83xx.h>
+#include <fsl_esdhc.h>
+#include <asm/io.h>
+#include <asm/fsl_serdes.h>
+#include <asm/fsl_mpc83xx_serdes.h>
+
+#include "mpc8308.h"
+
+#include <gdsys_fpga.h>
+
+#include "../common/osd.h"
+#include "../common/mclink.h"
+#include "../common/phy.h"
+
+#include <pca953x.h>
+#include <pca9698.h>
+
+#include <miiphy.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define MAX_MUX_CHANNELS 2
+
+enum {
+ UNITTYPE_MAIN_SERVER = 0,
+ UNITTYPE_MAIN_USER = 1,
+ UNITTYPE_VIDEO_SERVER = 2,
+ UNITTYPE_VIDEO_USER = 3,
+};
+
+enum {
+ UNITTYPEPCB_DVI = 0,
+ UNITTYPEPCB_DP_165 = 1,
+ UNITTYPEPCB_DP_300 = 2,
+ UNITTYPEPCB_HDMI = 3,
+};
+
+enum {
+ HWVER_100 = 0,
+ HWVER_110 = 1,
+};
+
+enum {
+ FPGA_HWVER_200 = 0,
+ FPGA_HWVER_210 = 1,
+};
+
+enum {
+ COMPRESSION_NONE = 0,
+ COMPRESSION_TYPE1_DELTA = 1,
+ COMPRESSION_TYPE1_TYPE2_DELTA = 3,
+};
+
+enum {
+ AUDIO_NONE = 0,
+ AUDIO_TX = 1,
+ AUDIO_RX = 2,
+ AUDIO_RXTX = 3,
+};
+
+enum {
+ SYSCLK_147456 = 0,
+};
+
+enum {
+ RAM_DDR2_32 = 0,
+ RAM_DDR3_32 = 1,
+};
+
+enum {
+ CARRIER_SPEED_1G = 0,
+ CARRIER_SPEED_2_5G = 1,
+};
+
+enum {
+ MCFPGA_DONE = 1 << 0,
+ MCFPGA_INIT_N = 1 << 1,
+ MCFPGA_PROGRAM_N = 1 << 2,
+ MCFPGA_UPDATE_ENABLE_N = 1 << 3,
+ MCFPGA_RESET_N = 1 << 4,
+};
+
+enum {
+ GPIO_MDC = 1 << 14,
+ GPIO_MDIO = 1 << 15,
+};
+
+unsigned int mclink_fpgacount;
+struct ihs_fpga *fpga_ptr[] = CONFIG_SYS_FPGA_PTR;
+
+int fpga_set_reg(u32 fpga, u16 *reg, off_t regoff, u16 data)
+{
+ int res;
+
+ switch (fpga) {
+ case 0:
+ out_le16(reg, data);
+ break;
+ default:
+ res = mclink_send(fpga - 1, regoff, data);
+ if (res < 0) {
+ printf("mclink_send reg %02lx data %04x returned %d\n",
+ regoff, data, res);
+ return res;
+ }
+ break;
+ }
+
+ return 0;
+}
+
+int fpga_get_reg(u32 fpga, u16 *reg, off_t regoff, u16 *data)
+{
+ int res;
+
+ switch (fpga) {
+ case 0:
+ *data = in_le16(reg);
+ break;
+ default:
+ if (fpga > mclink_fpgacount)
+ return -EINVAL;
+ res = mclink_receive(fpga - 1, regoff, data);
+ if (res < 0) {
+ printf("mclink_receive reg %02lx returned %d\n",
+ regoff, res);
+ return res;
+ }
+ }
+
+ return 0;
+}
+
+int checkboard(void)
+{
+ char *s = getenv("serial#");
+ bool hw_type_cat = pca9698_get_value(0x20, 20);
+
+ puts("Board: ");
+
+ printf("HRCon %s", hw_type_cat ? "CAT" : "Fiber");
+
+ if (s != NULL) {
+ puts(", serial# ");
+ puts(s);
+ }
+
+ puts("\n");
+
+ return 0;
+}
+
+static void print_fpga_info(unsigned int fpga, bool rgmii2_present)
+{
+ u16 versions;
+ u16 fpga_version;
+ u16 fpga_features;
+ unsigned unit_type;
+ unsigned unit_type_pcb_video;
+ unsigned hardware_version;
+ unsigned feature_compression;
+ unsigned feature_osd;
+ unsigned feature_audio;
+ unsigned feature_sysclock;
+ unsigned feature_ramconfig;
+ unsigned feature_carrier_speed;
+ unsigned feature_carriers;
+ unsigned feature_video_channels;
+
+ FPGA_GET_REG(fpga, versions, &versions);
+ FPGA_GET_REG(fpga, fpga_version, &fpga_version);
+ FPGA_GET_REG(fpga, fpga_features, &fpga_features);
+
+ unit_type = (versions & 0xf000) >> 12;
+ unit_type_pcb_video = (versions & 0x01c0) >> 6;
+ feature_compression = (fpga_features & 0xe000) >> 13;
+ feature_osd = fpga_features & (1<<11);
+ feature_audio = (fpga_features & 0x0600) >> 9;
+ feature_sysclock = (fpga_features & 0x0180) >> 7;
+ feature_ramconfig = (fpga_features & 0x0060) >> 5;
+ feature_carrier_speed = fpga_features & (1<<4);
+ feature_carriers = (fpga_features & 0x000c) >> 2;
+ feature_video_channels = fpga_features & 0x0003;
+
+ switch (unit_type) {
+ case UNITTYPE_MAIN_USER:
+ printf("Mainchannel");
+ break;
+
+ case UNITTYPE_VIDEO_USER:
+ printf("Videochannel");
+ break;
+
+ default:
+ printf("UnitType %d(not supported)", unit_type);
+ break;
+ }
+
+ if (unit_type == UNITTYPE_MAIN_USER) {
+ hardware_version =
+ (!!pca9698_get_value(0x20, 24) << 0)
+ | (!!pca9698_get_value(0x20, 25) << 1)
+ | (!!pca9698_get_value(0x20, 26) << 2)
+ | (!!pca9698_get_value(0x20, 27) << 3)
+ | (!!pca9698_get_value(0x20, 28) << 4);
+ switch (hardware_version) {
+ case HWVER_100:
+ printf(" HW-Ver 1.00,");
+ break;
+
+ case HWVER_110:
+ printf(" HW-Ver 1.10,");
+ break;
+
+ default:
+ printf(" HW-Ver %d(not supported),",
+ hardware_version);
+ break;
+ }
+ if (rgmii2_present)
+ printf(" RGMII2,");
+ }
+
+ if (unit_type == UNITTYPE_VIDEO_USER) {
+ hardware_version = versions & 0x000f;
+ switch (hardware_version) {
+ case FPGA_HWVER_200:
+ printf(" HW-Ver 2.00,");
+ break;
+
+ case FPGA_HWVER_210:
+ printf(" HW-Ver 2.10,");
+ break;
+
+ default:
+ printf(" HW-Ver %d(not supported),",
+ hardware_version);
+ break;
+ }
+ }
+
+ switch (unit_type_pcb_video) {
+ case UNITTYPEPCB_DVI:
+ printf(" DVI,");
+ break;
+
+ case UNITTYPEPCB_DP_165:
+ printf(" DP 165MPix/s,");
+ break;
+
+ case UNITTYPEPCB_DP_300:
+ printf(" DP 300MPix/s,");
+ break;
+
+ case UNITTYPEPCB_HDMI:
+ printf(" HDMI,");
+ break;
+ }
+
+ printf(" FPGA V %d.%02d\n features:",
+ fpga_version / 100, fpga_version % 100);
+
+
+ switch (feature_compression) {
+ case COMPRESSION_NONE:
+ printf(" no compression");
+ break;
+
+ case COMPRESSION_TYPE1_DELTA:
+ printf(" type1-deltacompression");
+ break;
+
+ case COMPRESSION_TYPE1_TYPE2_DELTA:
+ printf(" type1-deltacompression, type2-inlinecompression");
+ break;
+
+ default:
+ printf(" compression %d(not supported)", feature_compression);
+ break;
+ }
+
+ printf(", %sosd", feature_osd ? "" : "no ");
+
+ switch (feature_audio) {
+ case AUDIO_NONE:
+ printf(", no audio");
+ break;
+
+ case AUDIO_TX:
+ printf(", audio tx");
+ break;
+
+ case AUDIO_RX:
+ printf(", audio rx");
+ break;
+
+ case AUDIO_RXTX:
+ printf(", audio rx+tx");
+ break;
+
+ default:
+ printf(", audio %d(not supported)", feature_audio);
+ break;
+ }
+
+ puts(",\n ");
+
+ switch (feature_sysclock) {
+ case SYSCLK_147456:
+ printf("clock 147.456 MHz");
+ break;
+
+ default:
+ printf("clock %d(not supported)", feature_sysclock);
+ break;
+ }
+
+ switch (feature_ramconfig) {
+ case RAM_DDR2_32:
+ printf(", RAM 32 bit DDR2");
+ break;
+
+ case RAM_DDR3_32:
+ printf(", RAM 32 bit DDR3");
+ break;
+
+ default:
+ printf(", RAM %d(not supported)", feature_ramconfig);
+ break;
+ }
+
+ printf(", %d carrier(s) %s", feature_carriers,
+ feature_carrier_speed ? "2.5Gbit/s" : "1Gbit/s");
+
+ printf(", %d video channel(s)\n", feature_video_channels);
+}
+
+int last_stage_init(void)
+{
+ int slaves;
+ unsigned int k;
+ unsigned int mux_ch;
+ unsigned char mclink_controllers[] = { 0x24, 0x25, 0x26 };
+ u16 fpga_features;
+ bool hw_type_cat = pca9698_get_value(0x20, 20);
+ bool ch0_rgmii2_present = false;
+
+ FPGA_GET_REG(0, fpga_features, &fpga_features);
+
+ /* Turn on Parade DP501 */
+ pca9698_direction_output(0x20, 10, 1);
+
+ ch0_rgmii2_present = !pca9698_get_value(0x20, 30);
+
+ /* wait for FPGA done */
+ for (k = 0; k < ARRAY_SIZE(mclink_controllers); ++k) {
+ unsigned int ctr = 0;
+
+ if (i2c_probe(mclink_controllers[k]))
+ continue;
+
+ while (!(pca953x_get_val(mclink_controllers[k])
+ & MCFPGA_DONE)) {
+ udelay(100000);
+ if (ctr++ > 5) {
+ printf("no done for mclink_controller %d\n", k);
+ break;
+ }
+ }
+ }
+
+ if (hw_type_cat) {
+ miiphy_register(bb_miiphy_buses[0].name, bb_miiphy_read,
+ bb_miiphy_write);
+ for (mux_ch = 0; mux_ch < MAX_MUX_CHANNELS; ++mux_ch) {
+ if ((mux_ch == 1) && !ch0_rgmii2_present)
+ continue;
+
+ setup_88e1514(bb_miiphy_buses[0].name, mux_ch);
+ }
+ }
+
+ /* give slave-PLLs and Parade DP501 some time to be up and running */
+ udelay(500000);
+
+ mclink_fpgacount = CONFIG_SYS_MCLINK_MAX;
+ slaves = mclink_probe();
+ mclink_fpgacount = 0;
+
+ print_fpga_info(0, ch0_rgmii2_present);
+ osd_probe(0);
+
+ if (slaves <= 0)
+ return 0;
+
+ mclink_fpgacount = slaves;
+
+ for (k = 1; k <= slaves; ++k) {
+ FPGA_GET_REG(k, fpga_features, &fpga_features);
+
+ print_fpga_info(k, false);
+ osd_probe(k);
+ if (hw_type_cat) {
+ miiphy_register(bb_miiphy_buses[k].name,
+ bb_miiphy_read, bb_miiphy_write);
+ setup_88e1514(bb_miiphy_buses[k].name, 0);
+ }
+ }
+
+ return 0;
+}
+
+/*
+ * provide access to fpga gpios (for I2C bitbang)
+ * (these may look all too simple but make iocon.h much more readable)
+ */
+void fpga_gpio_set(unsigned int bus, int pin)
+{
+ FPGA_SET_REG(bus, gpio.set, pin);
+}
+
+void fpga_gpio_clear(unsigned int bus, int pin)
+{
+ FPGA_SET_REG(bus, gpio.clear, pin);
+}
+
+int fpga_gpio_get(unsigned int bus, int pin)
+{
+ u16 val;
+
+ FPGA_GET_REG(bus, gpio.read, &val);
+
+ return val & pin;
+}
+
+void mpc8308_init(void)
+{
+ pca9698_direction_output(0x20, 4, 1);
+}
+
+void mpc8308_set_fpga_reset(unsigned state)
+{
+ pca9698_set_value(0x20, 4, state ? 0 : 1);
+}
+
+void mpc8308_setup_hw(void)
+{
+ immap_t *immr = (immap_t *)CONFIG_SYS_IMMR;
+
+ /*
+ * set "startup-finished"-gpios
+ */
+ setbits_be32(&immr->gpio[0].dir, (1 << (31-11)) | (1 << (31-12)));
+ setbits_be32(&immr->gpio[0].dat, 1 << (31-12));
+}
+
+int mpc8308_get_fpga_done(unsigned fpga)
+{
+ return pca9698_get_value(0x20, 19);
+}
+
+#ifdef CONFIG_FSL_ESDHC
+int board_mmc_init(bd_t *bd)
+{
+ immap_t *immr = (immap_t *)CONFIG_SYS_IMMR;
+ sysconf83xx_t *sysconf = &immr->sysconf;
+
+ /* Enable cache snooping in eSDHC system configuration register */
+ out_be32(&sysconf->sdhccr, 0x02000000);
+
+ return fsl_esdhc_mmc_init(bd);
+}
+#endif
+
+static struct pci_region pcie_regions_0[] = {
+ {
+ .bus_start = CONFIG_SYS_PCIE1_MEM_BASE,
+ .phys_start = CONFIG_SYS_PCIE1_MEM_PHYS,
+ .size = CONFIG_SYS_PCIE1_MEM_SIZE,
+ .flags = PCI_REGION_MEM,
+ },
+ {
+ .bus_start = CONFIG_SYS_PCIE1_IO_BASE,
+ .phys_start = CONFIG_SYS_PCIE1_IO_PHYS,
+ .size = CONFIG_SYS_PCIE1_IO_SIZE,
+ .flags = PCI_REGION_IO,
+ },
+};
+
+void pci_init_board(void)
+{
+ immap_t *immr = (immap_t *)CONFIG_SYS_IMMR;
+ sysconf83xx_t *sysconf = &immr->sysconf;
+ law83xx_t *pcie_law = sysconf->pcielaw;
+ struct pci_region *pcie_reg[] = { pcie_regions_0 };
+
+ fsl_setup_serdes(CONFIG_FSL_SERDES1, FSL_SERDES_PROTO_PEX,
+ FSL_SERDES_CLK_100, FSL_SERDES_VDD_1V);
+
+ /* Deassert the resets in the control register */
+ out_be32(&sysconf->pecr1, 0xE0008000);
+ udelay(2000);
+
+ /* Configure PCI Express Local Access Windows */
+ out_be32(&pcie_law[0].bar, CONFIG_SYS_PCIE1_BASE & LAWBAR_BAR);
+ out_be32(&pcie_law[0].ar, LBLAWAR_EN | LBLAWAR_512MB);
+
+ mpc83xx_pcie_init(1, pcie_reg);
+}
+
+ulong board_flash_get_legacy(ulong base, int banknum, flash_info_t *info)
+{
+ info->portwidth = FLASH_CFI_16BIT;
+ info->chipwidth = FLASH_CFI_BY16;
+ info->interface = FLASH_CFI_X16;
+ return 1;
+}
+
+#if defined(CONFIG_OF_BOARD_SETUP)
+void ft_board_setup(void *blob, bd_t *bd)
+{
+ ft_cpu_setup(blob, bd);
+ fdt_fixup_dr_usb(blob, bd);
+ fdt_fixup_esdhc(blob, bd);
+}
+#endif
+
+/*
+ * FPGA MII bitbang implementation
+ */
+
+struct fpga_mii {
+ unsigned fpga;
+ int mdio;
+} fpga_mii[] = {
+ { 0, 1},
+ { 1, 1},
+ { 2, 1},
+ { 3, 1},
+};
+
+static int mii_dummy_init(struct bb_miiphy_bus *bus)
+{
+ return 0;
+}
+
+static int mii_mdio_active(struct bb_miiphy_bus *bus)
+{
+ struct fpga_mii *fpga_mii = bus->priv;
+
+ if (fpga_mii->mdio)
+ FPGA_SET_REG(fpga_mii->fpga, gpio.set, GPIO_MDIO);
+ else
+ FPGA_SET_REG(fpga_mii->fpga, gpio.clear, GPIO_MDIO);
+
+ return 0;
+}
+
+static int mii_mdio_tristate(struct bb_miiphy_bus *bus)
+{
+ struct fpga_mii *fpga_mii = bus->priv;
+
+ FPGA_SET_REG(fpga_mii->fpga, gpio.set, GPIO_MDIO);
+
+ return 0;
+}
+
+static int mii_set_mdio(struct bb_miiphy_bus *bus, int v)
+{
+ struct fpga_mii *fpga_mii = bus->priv;
+
+ if (v)
+ FPGA_SET_REG(fpga_mii->fpga, gpio.set, GPIO_MDIO);
+ else
+ FPGA_SET_REG(fpga_mii->fpga, gpio.clear, GPIO_MDIO);
+
+ fpga_mii->mdio = v;
+
+ return 0;
+}
+
+static int mii_get_mdio(struct bb_miiphy_bus *bus, int *v)
+{
+ u16 gpio;
+ struct fpga_mii *fpga_mii = bus->priv;
+
+ FPGA_GET_REG(fpga_mii->fpga, gpio.read, &gpio);
+
+ *v = ((gpio & GPIO_MDIO) != 0);
+
+ return 0;
+}
+
+static int mii_set_mdc(struct bb_miiphy_bus *bus, int v)
+{
+ struct fpga_mii *fpga_mii = bus->priv;
+
+ if (v)
+ FPGA_SET_REG(fpga_mii->fpga, gpio.set, GPIO_MDC);
+ else
+ FPGA_SET_REG(fpga_mii->fpga, gpio.clear, GPIO_MDC);
+
+ return 0;
+}
+
+static int mii_delay(struct bb_miiphy_bus *bus)
+{
+ udelay(1);
+
+ return 0;
+}
+
+struct bb_miiphy_bus bb_miiphy_buses[] = {
+ {
+ .name = "board0",
+ .init = mii_dummy_init,
+ .mdio_active = mii_mdio_active,
+ .mdio_tristate = mii_mdio_tristate,
+ .set_mdio = mii_set_mdio,
+ .get_mdio = mii_get_mdio,
+ .set_mdc = mii_set_mdc,
+ .delay = mii_delay,
+ .priv = &fpga_mii[0],
+ },
+ {
+ .name = "board1",
+ .init = mii_dummy_init,
+ .mdio_active = mii_mdio_active,
+ .mdio_tristate = mii_mdio_tristate,
+ .set_mdio = mii_set_mdio,
+ .get_mdio = mii_get_mdio,
+ .set_mdc = mii_set_mdc,
+ .delay = mii_delay,
+ .priv = &fpga_mii[1],
+ },
+ {
+ .name = "board2",
+ .init = mii_dummy_init,
+ .mdio_active = mii_mdio_active,
+ .mdio_tristate = mii_mdio_tristate,
+ .set_mdio = mii_set_mdio,
+ .get_mdio = mii_get_mdio,
+ .set_mdc = mii_set_mdc,
+ .delay = mii_delay,
+ .priv = &fpga_mii[2],
+ },
+ {
+ .name = "board3",
+ .init = mii_dummy_init,
+ .mdio_active = mii_mdio_active,
+ .mdio_tristate = mii_mdio_tristate,
+ .set_mdio = mii_set_mdio,
+ .get_mdio = mii_get_mdio,
+ .set_mdc = mii_set_mdc,
+ .delay = mii_delay,
+ .priv = &fpga_mii[3],
+ },
+};
+
+int bb_miiphy_buses_num = sizeof(bb_miiphy_buses) /
+ sizeof(bb_miiphy_buses[0]);
diff --git a/board/gdsys/mpc8308/mpc8308.c b/board/gdsys/mpc8308/mpc8308.c
new file mode 100644
index 0000000..4338a33
--- /dev/null
+++ b/board/gdsys/mpc8308/mpc8308.c
@@ -0,0 +1,109 @@
+/*
+ * (C) Copyright 2014
+ * Dirk Eibach, Guntermann & Drunck GmbH, eibach@gdsys.de
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <command.h>
+#include <asm/processor.h>
+#include <asm/io.h>
+#include <asm/ppc4xx-gpio.h>
+#include <asm/global_data.h>
+
+#include "mpc8308.h"
+#include <gdsys_fpga.h>
+
+#define REFLECTION_TESTPATTERN 0xdede
+#define REFLECTION_TESTPATTERN_INV (~REFLECTION_TESTPATTERN & 0xffff)
+
+#ifdef CONFIG_SYS_FPGA_NO_RFL_HI
+#define REFLECTION_TESTREG reflection_low
+#else
+#define REFLECTION_TESTREG reflection_high
+#endif
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int get_fpga_state(unsigned dev)
+{
+ return gd->arch.fpga_state[dev];
+}
+
+void print_fpga_state(unsigned dev)
+{
+ if (gd->arch.fpga_state[dev] & FPGA_STATE_DONE_FAILED)
+ puts(" Waiting for FPGA-DONE timed out.\n");
+ if (gd->arch.fpga_state[dev] & FPGA_STATE_REFLECTION_FAILED)
+ puts(" FPGA reflection test failed.\n");
+}
+
+int board_early_init_f(void)
+{
+ unsigned k;
+
+ for (k = 0; k < CONFIG_SYS_FPGA_COUNT; ++k)
+ gd->arch.fpga_state[k] = 0;
+
+ return 0;
+}
+
+int board_early_init_r(void)
+{
+ unsigned k;
+ unsigned ctr;
+
+ for (k = 0; k < CONFIG_SYS_FPGA_COUNT; ++k)
+ gd->arch.fpga_state[k] = 0;
+
+ /*
+ * reset FPGA
+ */
+ mpc8308_init();
+
+ mpc8308_set_fpga_reset(1);
+
+ mpc8308_setup_hw();
+
+ for (k = 0; k < CONFIG_SYS_FPGA_COUNT; ++k) {
+ ctr = 0;
+ while (!mpc8308_get_fpga_done(k)) {
+ udelay(100000);
+ if (ctr++ > 5) {
+ gd->arch.fpga_state[k] |=
+ FPGA_STATE_DONE_FAILED;
+ break;
+ }
+ }
+ }
+
+ udelay(10);
+
+ mpc8308_set_fpga_reset(0);
+
+ for (k = 0; k < CONFIG_SYS_FPGA_COUNT; ++k) {
+ /*
+ * wait for fpga out of reset
+ */
+ ctr = 0;
+ while (1) {
+ u16 val;
+
+ FPGA_SET_REG(k, reflection_low, REFLECTION_TESTPATTERN);
+
+ FPGA_GET_REG(k, REFLECTION_TESTREG, &val);
+ if (val == REFLECTION_TESTPATTERN_INV)
+ break;
+
+ udelay(100000);
+ if (ctr++ > 5) {
+ gd->arch.fpga_state[k] |=
+ FPGA_STATE_REFLECTION_FAILED;
+ break;
+ }
+ }
+ }
+
+ return 0;
+}
diff --git a/board/gdsys/mpc8308/mpc8308.h b/board/gdsys/mpc8308/mpc8308.h
new file mode 100644
index 0000000..dc07d56
--- /dev/null
+++ b/board/gdsys/mpc8308/mpc8308.h
@@ -0,0 +1,10 @@
+#ifndef __MPC8308_H_
+#define __MPC8308_H_
+
+/* functions to be provided by board implementation */
+void mpc8308_init(void);
+void mpc8308_set_fpga_reset(unsigned state);
+void mpc8308_setup_hw(void);
+int mpc8308_get_fpga_done(unsigned fpga);
+
+#endif /* __MPC8308_H_ */
diff --git a/board/gdsys/mpc8308/sdram.c b/board/gdsys/mpc8308/sdram.c
new file mode 100644
index 0000000..0fce8cf
--- /dev/null
+++ b/board/gdsys/mpc8308/sdram.c
@@ -0,0 +1,82 @@
+/*
+ * Copyright (C) 2007 Freescale Semiconductor, Inc.
+ * Copyright (C) 2010 Ilya Yanok, Emcraft Systems, yanok@emcraft.com
+ *
+ * Authors: Nick.Spence@freescale.com
+ * Wilson.Lo@freescale.com
+ * scottwood@freescale.com
+ *
+ * This files is mostly identical to the original from
+ * board\freescale\mpc8315erdb\sdram.c
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <mpc83xx.h>
+#include <spd_sdram.h>
+
+#include <asm/bitops.h>
+#include <asm/io.h>
+
+#include <asm/processor.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+/* Fixed sdram init -- doesn't use serial presence detect.
+ *
+ * This is useful for faster booting in configs where the RAM is unlikely
+ * to be changed, or for things like NAND booting where space is tight.
+ */
+static long fixed_sdram(void)
+{
+ immap_t *im = (immap_t *)CONFIG_SYS_IMMR;
+ u32 msize = CONFIG_SYS_DDR_SIZE * 1024 * 1024;
+ u32 msize_log2 = __ilog2(msize);
+
+ out_be32(&im->sysconf.ddrlaw[0].bar,
+ CONFIG_SYS_DDR_SDRAM_BASE & 0xfffff000);
+ out_be32(&im->sysconf.ddrlaw[0].ar, LBLAWAR_EN | (msize_log2 - 1));
+ out_be32(&im->sysconf.ddrcdr, CONFIG_SYS_DDRCDR_VALUE);
+
+ out_be32(&im->ddr.csbnds[0].csbnds, (msize - 1) >> 24);
+ out_be32(&im->ddr.cs_config[0], CONFIG_SYS_DDR_CS0_CONFIG);
+
+ /* Currently we use only one CS, so disable the other bank. */
+ out_be32(&im->ddr.cs_config[1], 0);
+
+ out_be32(&im->ddr.sdram_clk_cntl, CONFIG_SYS_DDR_SDRAM_CLK_CNTL);
+ out_be32(&im->ddr.timing_cfg_3, CONFIG_SYS_DDR_TIMING_3);
+ out_be32(&im->ddr.timing_cfg_1, CONFIG_SYS_DDR_TIMING_1);
+ out_be32(&im->ddr.timing_cfg_2, CONFIG_SYS_DDR_TIMING_2);
+ out_be32(&im->ddr.timing_cfg_0, CONFIG_SYS_DDR_TIMING_0);
+
+ out_be32(&im->ddr.sdram_cfg, CONFIG_SYS_DDR_SDRAM_CFG);
+ out_be32(&im->ddr.sdram_cfg2, CONFIG_SYS_DDR_SDRAM_CFG2);
+ out_be32(&im->ddr.sdram_mode, CONFIG_SYS_DDR_MODE);
+ out_be32(&im->ddr.sdram_mode2, CONFIG_SYS_DDR_MODE2);
+
+ out_be32(&im->ddr.sdram_interval, CONFIG_SYS_DDR_INTERVAL);
+ sync();
+
+ /* enable DDR controller */
+ setbits_be32(&im->ddr.sdram_cfg, SDRAM_CFG_MEM_EN);
+ sync();
+
+ return get_ram_size(CONFIG_SYS_DDR_SDRAM_BASE, msize);
+}
+
+phys_size_t initdram(int board_type)
+{
+ immap_t *im = (immap_t *)CONFIG_SYS_IMMR;
+ u32 msize;
+
+ if ((in_be32(&im->sysconf.immrbar) & IMMRBAR_BASE_ADDR) != (u32)im)
+ return -1;
+
+ /* DDR SDRAM */
+ msize = fixed_sdram();
+
+ /* return total bus SDRAM size(bytes) -- DDR */
+ return msize;
+}